Samsung Computer Monitor STM 19LV User Guide

Professional Security LCD Monitor  
INSTRUCTION MANUAL  
SALES NETWORK  
SAMSUNG TECHWIN CO., LTD.  
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,  
Gyeonggi-do 462-703, Korea  
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.  
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China  
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514  
TEL : +82-31-740-8137~8141 FAX : +82-31-740-8145  
SAMSUNG OPTO-ELECTRONICS UK, LTD.  
Samsung House, 1000 Hillswood Drive, Hillswood Business Park  
Chertsey, Surrey KT16 OPS  
STM-19LV/17LV  
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325  
About this manual  
VAN 06. 03  
Please read this manual carefully before installing and using the camera. Be sure to keep the manual handy for later reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USER  
MANUAL  
USER  
MANUAL  
FCC RF INTERFERENCE STATEMENT  
NOTE  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures.  
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
- Consult the dealer or an experienced radio, TV technician for help.  
- Only shielded interface cable should be used.  
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or  
manufacturer could void the users authority to operate such equipment.  
CAUTION  
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed  
near the equipment and is easily accessible.  
CAUTION TO SERVICE PERSONNEL  
• DOC COMPLIANCE NOTICE  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set  
out in the radio interference regulation of Canadian Department of communications.  
POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT.  
UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING.  
CONNECTING WITH EXTERNAL EQUIPMENT  
CAUTIONS  
• NEVER REMOVE THE BACK COVER  
A. BOTTOM PANEL CONTROL  
Removal of the back cover should be carried out only by qualified personnel.  
1
2
3
4
5
6
7
8
9
10  
11  
• DO NOT USE IN HOSTILE ENVIRONMENTS  
To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in  
the office or home. Do not subject the unit to vibrations, dust of corrosive gases.  
• KEEP IN A WELL VENTILATED PLACE  
Ventilation holes are provided on the cabinet to prevent the temperature from rising. Do not cover the unit or  
place anything on the top of unit.  
VCR  
CAMERA A  
CAMERA B  
DVR  
• AVOID HEAT  
Avoid placing the unit in direct sunshine or near a heating appliance.  
• TO ELIMINATE EYE FATIGUE  
1. DC 12V IN  
2. D-SUB IN : PC Signal Input  
3. VIDEO 1(AV1) IN : Composite signal Input for AV1  
Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly  
on the monitor.  
4. VIDEO 1(AV1) OUT : Video looping output for AV1  
5. VIDEO 2(AV2) IN : Composite signal Input for AV2  
6. VIDEO 2(AV2) OUT : Video looping output for AV2  
7. AUDIO 1 IN : Stereo Audio Signal Input, This input is for AV1, S-VIDEO  
8. AUDIO 2 IN : Stereo Audio Signal Intput, This Output is for AV2  
9. S-VIDEO (Y/C) IN : Y/C separated signal input  
• BE CAREFUL OF HEAVY OBJECT  
Neither the monitor itself nor any other heavy object should rest on the power cord. Damage to a power cord  
can cause fire or electrical shock.  
10. S-VIDEO (Y/C) OUT : Y/C separated signal looping output 11. PC STEREO IN  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
USER  
MANUAL  
USER  
MANUAL  
7. IR Sensor  
Remote controller sensor.  
REMOTE FUNCTIONS  
8. POWER ON/OFF(  
)
1
Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED  
(next to the power switch) lights with green when the power is turned ON. The power is turned off by  
pressing the power switch again and the power LED goes Red.  
B. REMOTE CONTROLLER  
2
1. POWER( ) :  
Turns the power ON or OFF.  
There will be a few seconds delay before the display appears.  
3
• SELF-TEST DISPLAY  
2. SOURCE :  
When there is no connection at PC, the On Screen Display will show  
for 3 seconds.  
Select pc or video(PC / AV1 / AV2 / S-Video) sources.  
5
4
8
3. MUTE : Mute the sound.  
6
7
4. MENU : Activates and exits the On Screen Display.  
5. VOL(  
Increases or decreases the level of audio volume.  
6. UP/DOWN( ) : Move to OSD menu.  
) :  
• OSD MENU DESCRIPTION  
Input Source : Select PC or AV1, SVIDEO.  
7. AUTO : Auto geometry adjustment in PC Source.  
8. EXIT : Exit the On Screen Display.  
Screen :  
CONTROLS AND FUNCTIONS  
Brightness - Increase or decrease the intensity of the image.  
Contrast - Increase or decrease the intensity(lightness or  
dimness) of the image.  
H. position(PC Mode Only) - Move image horizontally on screen  
right or left.  
V. position(PC Mode Only) - Move image vertically on screen  
up or down.  
1
2
3
4
5
6
7
8
Clock(PC Mode Only) - Adjust the vertical noise of screen image.  
• Front Key Control  
Phase(PC Mode Only) - Adjust the number of horizontal picture elements.  
1. SOURCE  
Select input source, and move the previous menu.  
2. MENU  
Audio  
Volume : Adjust audio volume.  
Activates and exits the On Screen Display. This button can also be used to move previous menu or status.  
OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit.  
3/4. DOWN / UP  
This button allows user to enter the sub-menu of the activated function. when down key is pressed on the  
main menu.  
5/6. VOL< / VOL >  
Adjust the volume / Adjust menu settings.  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
USER  
MANUAL  
USER  
MANUAL  
OSD :  
MOUNTING GUIDE  
H. Position - Move the OSD position to right( ) or left( ).  
V. Position - Move the OSD position to up( ) or down( ).  
Transparency - Select the OSD background.  
Wall mountable using two methods:  
1) Using the 200 mm pre-cut holes  
2) Using the VESA standard wall mount design and the 100mm hole pattern on the back panel to install the LCD  
monitor to the wall.  
OSD Timer - Select the OSD display timing.  
Language - Select a language among  
English, Français, Deutsch, Español, Danish, Italiano.  
Color (PC Mode) :  
Wall  
Color Temp - Adjust color temperature to 9300, 6500, user.  
(note : 9300 is factory default)  
Pad  
Arm  
Red - Adjust red color for user.  
Green - Adjust green color for user.  
Blue - Adjust blue color for user.  
Monitor  
D-SUB CONNECTOR PIN ASSIGNMENTS  
• PIN ASSIGNMENTS  
Utility :  
Recall - Select to reset all setting to the factory default values.  
Lock - Select ON or OFF  
(ON : Control key lock. OFF : Control key unlock)  
Pin 1  
Pin 2  
Pin 3  
Pin 4  
Pin 5  
Pin 6  
Pin 7  
Pin 8  
RED VIDEO  
Pin 9  
GREEN VIDEO  
BLUE VIDEO  
GROUND  
Pin10  
Pin 11  
Pin 12  
Pin 13  
Pin 14  
Pin 15  
SIGNAL CABLE DETECT  
GROUND  
SAD(for DDC)  
D-SUB  
GROUND  
H-SYNC.(or H+V SYNC.)  
V-SYNC  
RED GROUND  
GREEN GROUND  
BLUE GROUND  
Exit : Turn off OSD Menu.  
SLC(for DDC)  
• ACCESSORY  
1. POWER CORD  
5. Remote Control  
2. USER’S MANUAL  
6. Batteries  
3. PC cable  
7. Wall mount (Option)  
4. Adaptor  
8. Rack mount (Option)  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
USER  
MANUAL  
USER  
MANUAL  
POWER MANAGEMENT  
SPECIFICATIONS  
This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The  
display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card  
performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an  
appropriate mode through identifying each of the three modes of the signaling system.  
Model Name  
Composite  
STM-19LV  
STM-17LV  
2ch input 1.0Vp-p, 75terminated, loop-through out  
1ch input (Y/C), loop-through out  
1ch input  
Video  
S-VIDEO  
VGA  
Resolution  
Frequency  
1280x1024@60Hz  
Horizontal(KHz)  
Vertical(Hz)  
31KHz ~ 82KHz  
• POWER CONSUMPTION  
50Hz ~ 77Hz  
720x480@60Hz, 720x576@50Hz, 800x600@60/75Hz  
1024x768@60/75Hz, 1280x1024@60/75Hz  
Max. 42W  
MODE  
ON  
POWER CONSUMPTION  
MODE  
SUSPEND  
ACTIVE OFF  
POWER CONSUMPTION  
VGAMode  
<50W  
<5W  
<5W  
<5W  
Power Consumption  
Dimensions  
(WxDxH)  
Max. 36W  
Net  
Packing  
Net Weight  
Gross Weight  
STANDBY  
430x428x200mm  
490x506x225mm  
6.61Kg  
382.4x390.5x200mm  
436x476x225mm  
5.96Kg  
Weight(kg)  
• LED INDICATOR  
8.43Kg  
7.67Kg  
Power Supply  
DC 12V / 4A  
50˚F~104˚F (10˚C~4˚C)  
10%~80%, Non-condensing  
-4˚F~113˚F (-20˚C~45˚C)  
5%~95%,Non-condensing  
The power management feature of the monitor is comprised of four stages : On(Green), Standby, Suspend,  
Active off(Red & Green) and Unsupported mode(Green).  
Operating Temperature  
Operating Humidity  
Storage Temperature  
Storage Humidity  
Size  
Active Display Area  
Pixel Pitch(mm)  
Brightness(cd/m2)  
Contrast Ratio  
Environmental  
Considerations  
MODE  
ON  
STANDBY  
SUSPEND  
ACTIVE OFF  
UNSUPPORTED MODE  
POWER OFF  
LED COLOR  
MONITOR OPERATION  
GREEN  
Normal Operation  
19" Diagonal AM-TFT  
376.32x301.056mm  
17" Diagonal AM-TFT  
337.92x270.336mm  
Screen blanks after preset ide time and some electronic circuits or all  
circuitry in the monitor shutdown.  
AMBER  
0.294mm(H) x 0.294mm(V)  
0.264mm(H) x 0.264mm(V)  
LCD Panel Spec  
300cd/m2  
700:1  
8ms  
GREEN  
RED  
Normal operation but the on screen display will show error massage.  
Not opreation  
Response Time(ms)  
Viewing Angle(L/R/ T/B)  
75/75/75/60  
TROUBLESHOOTING GUIDE  
DIMENSION  
TROUBLE  
TROUBLESHOOTING TIP  
No image on display screen  
1. Check that power cord of the monitor have been connected securely  
into wall outlet or grounded extension cable or strip.  
STM-19LV  
STM-17LV  
2. Power switch should be in the ON position and LED is lit.  
3. Check that the Brightness and / or the Contrast adjustments of the Display haver not  
been turned down to minimum levels.  
“Check Input Signal” message on  
screen  
1. The signal cable should be completely connected to the video card / computer  
2. The video card should be completely seated in its slot and the computer is  
switched ON.  
Display image is not centered, too small  
or toolarge in PC mode  
Push the down key in front side or Auto key in remocon.  
Adjust Clock and Phase in the OSD.  
Vertical or Horizontal noise is  
present in the picture  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  

QSC Audio Portable Speaker AD S282H User Guide
Radio Shack Cordless Telephone 24 GHz Digital Spread Spectrum Cordless Telephone with Caller ID Call Waiting Deluxe User Guide
Radio Shack Cordless Telephone 43 3870 User Guide
Raypak Boiler 42 180 User Guide
RCA Flat Panel Television HD61LPW163 User Guide
Renesas Computer Hardware M30830T EPBM User Guide
Ricoh Printer SP 311DNw User Guide
Rikaline GPS Receiver CF GPS GPS 6020 User Guide
Samsung Fax Machine SF 360 Series User Guide
Samsung Flat Panel Television 2433BW User Guide