SyncMaster 153V/173V/152V/172V/193V/192V/153S/173S/153B/173B
Download from Www.Somanuals.com. All Manuals Search And Download.
Notational
Power
Installation
Clean
Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Disconnect the plug from the outlet
Do not disassemble
Do not touch
Grounding to prevent an electric shock
Download from Www.Somanuals.com. All Manuals Search And Download.
When not used for extended periods of time, set your PC to DPMS. If using
a screen saver, set it to the active screen mode.
Notational
Power
Installation
Clean
Do not use a damaged or loose plug.
z
This may cause an electric shock or fire.
Other
Do not pull the plug out by the wire nor touch the plug with wet
hands.
z
This may cause an electric shock or fire.
Use only a properly grounded plug and reoeptacle.
z
An improper ground may cause electric shock or equipment
damage.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
z
Failure to do so may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or
if it is not used for a long period of time.
z
Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
This may cause a fire.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not cover the vents on the monitor cabinet.
Bad ventilation may cause a breakdown or fire.
z
Notational
Power
Installation
Clean
Put your monitor in a location with low humidity and a minimum of
dust.
Other
z
An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it.
This may cause damage to the product or human body.
z
Place the monitor on a flat and stable surface.
The monitor can cause injury by falling.
z
Set down the monitor carefully.
It could be damaged or broken.
z
Do not place the monitor face down.
The CDT surface may be damaged.
z
Download from Www.Somanuals.com. All Manuals Search And Download.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a
slightly moistened, soft fabric.
Notational
Power
Do not spray detergent directly on the monitor.
Installation
Clean
Other
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty,
clean it properly with a dry cloth.
z
A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects
on the monitor.
z
z
This may cause damage, electric shock or a fire.
If a foreign substance gets into the monitor, disconnect the plug
and then contact a service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not remove cover(or back). No user serviceable parts inside.
z
z
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
Notational
Power
Installation
Clean
If your monitor does not operate normally - in particular, if there
are any unusual sounds or smells coming from it - unplug it
immediately and contact an authorized dealer or service.
Other
z
This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor.
This may cause an electric shock or a fire.
z
For each hour of looking at the monitor, you should let your eyes
rest for 5 minutes.
z
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
This may cause an explosion or fire.
z
Do not try to move the monitor by pulling on the wire or the signal
cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
z
Keep all power adaptors apart.
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Possible fire hazard.
Keep power adaptor away from any other heat source.
Possible fire hazard.
z
Remove and discard vinyl bag from power adaptor before use.
Possible fire hazard.
z
Always keep power adaptor in well-ventilated area.
If you view a fixed screen for an extended period of time, residual
image or blurriness may appear.
z
Change the mode to energy save or set a screensaver to moving
picture when you need to be away from the monitor for an
extended period of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not remove cover(or back). No user serviceable parts inside.
z
z
This may cause an electric shock or a fire.
Refer servicing to qualified service personnel.
Notational
Power
Installation
Clean
If your monitor does not operate normally - in particular, if there
are any unusual sounds or smells coming from it - unplug it
immediately and contact an authorized dealer or service.
Other
z
This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor.
This may cause an electric shock or a fire.
z
For each hour of looking at the monitor, you should let your eyes
rest for 5 minutes.
z
This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor.
This may cause an explosion or fire.
z
Do not try to move the monitor by pulling on the wire or the signal
cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Do not move the monitor right or left by pulling only the wire or the
signal cable.
z
This may cause a breakdown, electric shock or a fire due to
damage to the cable.
Never insert anything metallic into the monitor openings.
This may cause an electric shock, fire or injury.
z
Keep all power adaptors apart.
Download from Www.Somanuals.com. All Manuals Search And Download.
z
Possible fire hazard.
Keep power adaptor away from any other heat source.
Possible fire hazard.
z
Remove and discard vinyl bag from power adaptor before use.
Possible fire hazard.
z
Always keep power adaptor in well-ventilated area.
If you view a fixed screen for an extended period of time, residual
image or blurriness may appear.
z
Change the mode to energy save or set a screensaver to moving
picture when you need to be away from the monitor for an
extended period of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/173V/152V/172V/193V/192V
Power Cord
Signal Cable
Monitor and Stand
Unpacking
Front
Rear
Quick Setup Guide
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Warranty Card
(Not available in all locations)
User's Guide and Driver Installation CD
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
Power Cord
DC-Adapter
Monitor and Pivot Stand
Unpacking
Front
Rear
Signal Cable
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide and Driver Installation CD
Pivot S/W CD(Option)
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
Power Cord
DC-Adapter
Monitor and Stand
Unpacking
Front
Rear
Signal Cable
Please make sure the following items are included
with your monitor. If any items are missing,
contact your dealer.
Audio Cable
Quick Setup Guide
Warranty Card
(Not available in all locations)
User's Guide and Driver Installation CD
Pivot S/W CD(Option)
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/173V/152V/172V/193V/192V
Unpacking
Front
Rear
1. Auto button /
Exit button
Use this button to auto adjustment direct access. /
Use this button to Exit the active menu or the OSD.
2. Menu button
These buttons allow you to highlight and adjust items in the menu.
Use this button to turn the monitor on and off.
3. Power button
4. Adjust buttons
a. Power indicator
These buttons allow you to highlight and adjust items in the menu.
This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments.
Note: See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
Unpacking
Front
Rear
1. Auto button /
Use this button to auto adjustment direct access. /
Use this button to Exit the active menu or the OSD.
Exit button
2. Menu button
3. Power button
4. Adjust buttons
a. Power indicator
These buttons allow you to highlight and adjust items in the menu.
Use this button to turn the monitor on and off.
These buttons allow you to highlight and adjust items in the menu.
This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments.
Note: See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
Unpacking
Front
Rear
1. Auto button /
Use this button to auto adjustment direct access. /
Use this button to Exit the active menu or the OSD.
Exit button
2. Menu button
3. Power button
4. Adjust buttons
These buttons allow you to highlight and adjust items in the menu.
Use this button to turn the monitor on and off.
These buttons allow you to highlight and adjust items in the menu.
When OSD is not on the screen, push the - or + button to adjust volume.
a. Power indicator
This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments.
b. PC sound connection Connect the audio cable for your monitor to the audio port on the back of
terminal
your computer.
c. Headphone
connection terminal
Note: See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it
unattended for long periods.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/173V/152V/172V/193V/192V
Unpacking
Front
Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
Connect the power cord for your monitor to the power port on the back
of the monitor.
2. Signal port
Connect the signal cable to the 15-pin, D-sub connector on the back of
your monitor.
Note: See Connecting Your Monitor for further information regarding cable connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
Unpacking
Front
Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
2. Signal port
3. Pin
Connect the DC Adapter for your monitor to the power port on the back
of the monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back of
your monitor.
Press the button on the bottom rear of the stand in order to lock down
the stand.
Note : Always have your monitor faced front side down on a level
surface (not resting on the stand) before locking it down. Pressing the
button while the monitor stand is resting on a flat surface may cause
your monitor to topple or fall and cause personal injury and/or damage
to the unit.
Note: See Connecting Your Monitor for further information regarding cable connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
Unpacking
Front
Rear
(The configuration at the back of the monitor may vary from product to product.)
1. Power port
2. Signal port
3. Pin
Connect the power cord for your monitor to the power port on the back
of the monitor.
Connect the signal cable to the 15-pin, D-sub connector on the back of
your monitor.
Press the button on the bottom rear of the stand in order to lock down
the stand.
Note : Always have your monitor faced front side down on a level
surface (not resting on the stand) before locking it down. Pressing the
button while the monitor stand is resting on a flat surface may cause
your monitor to topple or fall and cause personal injury and/or damage
to the unit.
Note: See Connecting Your Monitor for further information regarding cable connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/173V/152V/172V/193V/192V
English > Main > Setup > Connecting Your Monitor
Connecting
Your Monitor
Installing the
Monitor Driver
Installing VESA
compliant mounting
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
3. Connect the monitor to the Macintosh computer using the D-SUB connection cable.
4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adaptor.
5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
English > Main > Setup > Connecting Your Monitor
Connecting
Your Monitor
Installing the
Monitor Driver
Installing VESA
compliant mounting
1. Connect the DC Adapter for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
3. Connect the monitor to the Macintosh computer using the D-SUB connection cable.
4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adaptor.
5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
English > Main > Setup > Connecting Your Monitor
Connecting
Your Monitor
Installing the
Monitor Driver
Installing VESA
compliant mounting
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.
2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
3. Connect the audio cable for your monitor to the audio port on the back of your computer.
4. Connect the monitor to the Macintosh computer using the D-SUB connection cable.
5. In the case of an old model Macintosh, you need to connect the monitor using a special Mac
adaptor.
6. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
1. PC sound connection terminal (Input)
2. Headphone connection terminal (Output)
3. Volume
4. To listen in privacy,connect headphones here.
5. Connect a sound cable from the input source (sound card,computer,CD-ROM drive).
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing VESA
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
compliant mounting
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
http://www.sec.co.kr/monitor/ (Korea)
Windows ME
1. Insert CD into the CD-ROM drive.
2. Click "Windows ME Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.
Windows XP/2000
1. Insert CD into the CD-ROM drive.
2. Click "Windows XP/2000 Driver".
3. Choose your monitor model in the model list, then click the "OK" button.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click the "Install" button in the "Warning" window.
5. If you can see following "Message" window, then click the "Continue Anyway" button.
Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
6. Monitor driver installation is completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your
Monitor
Installing the
Monitor Driver
Installing VESA
When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions as appropriate for the operating system you
have.
compliant mounting
Prepare a blank disk and download the driver program file at the Internet web site shown
here.
z
http://www.sec.co.kr/monitor/ (Korea)
®
®
Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the
model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
Download from Www.Somanuals.com. All Manuals Search And Download.
This monitor driver is under certifying MS logo,and this installation don't damage your
system.The certified driver will be posted on Samsung Monitor Homepage
9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
®
®
Microsoft Windows 2000 Operating System
When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window.
2. Click the "Browse" button on the "File Needed" window.
3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install
1. Click "Start" , "Setting" , "Control Panel".
2. Double click the "Display" Icon.
3. Choose the "Settings" tab and then click "Advanced..".
4. Choose "Monitor".
Case1: If the "Properties" button is inactive, it means your monitor is properly configured.
Please stop installation
Case2: If the "Properties" button is active, click the "Properties" button then follow next
steps continually.
5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
6. Choose "Display a list of the known drivers for this device so that I can choose a
specific driver" then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver).
8. Click the "Open" button, then click "OK" button.
9. Choose your monitor model and click the "Next" button then click "Next" button.
10. Click the "Finish" button then the "Close" button.
If you can see the "Digital Signature Not Found" window then click the "Yes"button.
And click the "Finish" button then the "Close" button.
®
®
Microsoft Windows Millennium Operating System
1. Click "Start" , "Setting" , "Control Panel".
2. Double click "Display" icon.
3. Select the "Settings" tab and click "Advanced Properties" button.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Select the "Monitor" tab.
5. Click the "Change" button in the "Monitor Type" area.
6. Choose "Specify the location of the driver".
7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.
8. Click the "Have Disk" button
9. Specify A:\(D:\driver) then click "OK" button.
10. Select "Show all devices" and choose the monitor that corresponds to the one you
connected to your computer and click "OK".
11. Continue choosing "Close" button and "OK" button until you close the Display Properties
dialogue box.
(You can get some other screen for warning message or others, then click the appreciate
option for your monitor.)
®
®
Microsoft Windows NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon.
2. In Display Registration Information window, click Settings Tab and then click All Display
Modes.
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.
4. Click Apply button if you see the screen working normally after clicking Test. If the screen
is not normal, change to a different mode (lower mode of resolution, colors or frequency).
Note: If there is no Mode at All Display Modes, select the level of resolution and vertical
frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System
To execute X-Window, you need to make the X86Config file, which is a type of system setting
file.
1. Press Enter at the first and the second screen after executing the X86Config file.
2. The third screen is for setting your mouse.
3. Set a mouse for your computer.
4. The next screen is for selecting a keyboard.
5. Set a Keyboard for your computer.
6. The next screen is for setting your monitor.
7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency
directly.)
8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)
9. Enter the model name of your monitor. This information will not affect the actual
execution of X-Window.
10. You have finished setting up your monitor.
Execute X-Window after setting other requested hardware.
Download from Www.Somanuals.com. All Manuals Search And Download.
Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with
the four screws that came with the arm-type base, wall mount hanger or other base.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
Removing the base
Connecting Your
Monitor
Installing the
Monitor Driver
Installing VESA
compliant
mounting
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the
screen.
3. Remove the two screws and then remove the Stand from the LCD monitor.
Attaching a base
NOTE: This monitor accepts a 75mm x 75mm VESA-compliant mounting interface pad.
1. Rear cover mounting pad
2. Mounting interface pad
Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with
the four screws that came with the arm-type base, wall mount hanger or other base.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
Removing the base
Connecting Your
Monitor
Installing the
Monitor Driver
Installing VESA
compliant
mounting
1. Turn off your monitor and unplug its power cord.
2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the
screen.
3. Remove the two screws and then remove the Stand from the LCD monitor.
Attaching a base
NOTE: This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad.
1. Rear cover mounting pad
2. Mounting interface pad
Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with
the four screws that came with the arm-type base, wall mount hanger or other base.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/173V/152V/172V/193V/192V
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/173S
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B/173B
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling for service, check the information in this section to see if you can remedy any
problems yourself. If you do need assistance, please call the phone number on the warranty
card, the phone number on the Information section or contact your dealer.
Check List
Symptom
Check List
Solutions
Q & A
Self-Test Feature
Check
No images on the
screen. I cannot turn properly?
Is the power cord connected
Check the power cord connection
and supply.
on the monitor.
Can you see "No Connection,
Check the signal cable connection.
Check Signal Cable" on the
screen?
If the power is on, reboot the
computer to see the initial
screen(the login screen), which
can be seen.
If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows ME/XP/2000 ) and then
change the frequency of the video
card.
(Refer to the Preset Display Modes)
Note: If the initial screen (the login
screen) does not appear, contact a
service center or your dealer.
Can you see "Video mode not
supported" on the screen?
You can see this message when the
signal from the video card exceeds
the maximum resolution and
frequency that the monitor can
properly handle.
Adjust the maximum resolution and
frequency that the monitor can
properly handle.
There is no image on the
screen. Is the power indicator
on the monitor blinking at 1
second intervals?
The monitor is in PowerSaver mode.
Press a key on the keyboard or move
the mouse to activate the monitor
and restore the image on the screen.
I cannot see the On
Screen Display.
Have you locked the On Screen Unlock the OSD by pressing the
Display (OSD) Menu to prevent
MENU button for at least 5 seconds.
changes?
The screen shows
strange colors or
just black and white. screen through a cellophane
Is the screen displaying only
one color as if looking at the
Check the signal cable connection.
Make sure the video card is fully
inserted in it's slot.
paper?
Have the screen colors become
strange after running a program
or due to a crash between
applications?
Reboot the computer.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
The screen
suddenly has
become
Have you changed the video
card or the driver?
Adjust screen image position and
size using the OSD.
Download from Www.Somanuals.com. All Manuals Search And Download.
unbalanced.
Have you adjusted the
resolution or frequency to the
monitor?
Adjust the resolution and frequency
at the video card.
(Refer to the Preset Display Modes).
The screen can be unbalanced due to the cycle of the video card
signals. Readjust Position by referring to the OSD.
The screen is out of
focus or OSD
cannot be adjusted.
Have you adjusted the
resolution or frequency on the
monitor?
Adjust the resolution and frequency
of the video card.
(Refer to the Preset Display Modes).
LED is blinking but
no images on the
screen.
Is the frequency properly
adjusted when checking the
Display Timing on the menu?
Adjust the frequency properly by
referring to the video card manual
and the Preset Display Modes.
(The maximum frequency per
resolution may differ from product to
product.)
There are only 16
colors shown on the
screen. The screen
colors have
Have the Windows colors been
set properly?
For Windows ME/XP/2000 :
Set the colors properly at the
Control Panel, Display, Settings.
changed after
changing the video
card.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
There is a message
that reads
Have you installed the monitor
driver?
Install the monitor driver according to
the Driver Installation Instructions.
"Unrecognized
monitor, Plug & Play
(VESA DDC) monitor
found".
See the video card manual to
see if the Plug & Play (VESA
DDC) function can be
supported.
Install the monitor driver according to
the Driver Installation Instructions.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "Control Panel, System, Device Administrator" and then
reboot the computer to reinstall the adapter (video) driver.
Note: If problems repeatedly occur, contact an authorized service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
How can I change the frequency?
Frequency can be changed by reconfiguring the video
card.
Check List
Q & A
Self-Test Feature
Check
Note that video card support can vary, depending on the
version of the driver used.
(Refer to the computer or the video card manual for
details.)
How can I adjust the resolution?
Windows ME/XP/2000 : Set the resolution at the Control
Panel, Display, Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows ME/XP/2000 : Set the function at BIOS-SETUP
of the computer or the screen saver. (Refer to
Windows/Computer Manual).
How can I clean the outer case/LCD
Panel?
Disconnect the power cord and then clean the monitor
with a soft cloth, using either a cleaning solution or plain
water.
Do not leave any remains of the detergent nor scratch the
case. Do not allow any water to go inside the monitor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your monitor provides a self test feature that allows you to check whether your monitor is
functioning properly.
Check List
Q & A
Self-Test
Feature Check
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
If the monitor is functioning properly, you will see a box with a border and text inside as
shown in the following illustration:
The three boxes inside the border are red, green and blue.
Failure of any of the boxes to appear indicates a problem with your monitor. This box
also appears during normal operation if the video cable becomes disconnected or
damaged.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your
video controller and computer system; your monitor is functioning properly.
If there is something wrong with the input signal, a message appears on the screen or
the screen goes blank although the power indicator LED is still on. The message may
indicate that the monitor is out of scan range or that you need to check the signal cable.
The location and the position of the monitor may influence the quality and other
features of the monitor.
1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another
room.
2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3
Download from Www.Somanuals.com. All Manuals Search And Download.
feet (one meter) of the monitor.
z
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the
PC or the video card, this can cause the monitor to become blank, have poor coloring, noise,
Video mode not supported, etc. In this case, first check the source of the problem, and then
contact a service center or your dealer.
z
Judging the monitor's working condition
If there is no image on the screen or an "Video mode not supported" message comes up,
disconnect the cable from the computer while the monitor is still powered on.
{
If there is a message coming up on the screen or if the screen goes white, this means
the monitor is in working condition.
{
In this case, check the computer for trouble.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 153V
General
Size
15.0 inch diagonal
304.1 (H) x 228.1 (V)
0.297 (H) x 0.297 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 61 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1024 x 768@60Hz
1024 x 768@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, TTL level positive or negative
Maximum Pixel Clock
80 MHz
Power Supply
AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
32W (Maximum)
Dimensions (WxDxH)
353.5 x 57.0 x 280.5 mm (Without Stand)
353.5 x 150 x 345.0 mm (After folding the Stand)
Weight
3.4kg (With Simple Stand)
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
Download from Www.Somanuals.com. All Manuals Search And Download.
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the number of TFT LCD pixels that is contained in this product are 2.359.296.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 173V
General
Size
17.0 inch diagonal
337.92 (H) x 270.336 (V)
0.264 (H) x 0.264 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite,
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
40W (Maximum)
Dimensions (WxDxH)
382.0 x 61.0 x 319.0 mm (Without Stand)
382.0 x 175.0 x 388.0 mm (After folding the Stand)
Weight
4.8kg (With Simple Stand)
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 152V
General
Size
15.0 inch diagonal
304.1 (H) x 228.1 (V)
0.297 (H) x 0.297 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 61 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1024 x 768@60Hz
1024 x 768@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, TTL level positive or negative
Maximum Pixel Clock
80 MHz
Power Supply
AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
32W (Maximum)
Dimensions (WxDxH)
353.5 x 57.0 x 280.5 mm (Without Stand)
353.5 x 150 x 345.0 mm (After folding the Stand)
Weight
3.4kg (With Simple Stand)
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
Download from Www.Somanuals.com. All Manuals Search And Download.
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the number of TFT LCD pixels that is contained in this product are 2,359,296.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 172V
General
Size
17.0 inch diagonal
337.92 (H) x 270.336 (V)
0.264 (H) x 0.264 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite,
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
40W (Maximum)
Dimensions (WxDxH)
382.0 x 61.0 x 319.0 mm (Without Stand)
382.0 x 175.0 x 388.0 mm (After folding the Stand)
Weight
4.8kg (With Simple Stand)
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 193V
General
Size
19.0 inch diagonal
404.6 (H) x 330.0 (V)
0.294 (H) x 0.294 (V)
a-si TFT active matrix
85/85/85/85(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite,
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
45W (Maximum)
Dimensions (WxDxH)
428.0 x 59.5 x 356.0 mm (Without Stand)
428.0 x 204.0 x 433.0 mm (After folding the Stand)
Weight
6.7kg (With Basic Stand)
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 192V
General
Size
19.0 inch diagonal
404.6 (H) x 330.0 (V)
0.294 (H) x 0.294 (V)
a-si TFT active matrix
85/85/85/85(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,294,277 colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite,
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
45W (Maximum)
Dimensions (WxDxH)
428.0 x 59.5 x 356.0 mm (Without Stand)
428.0 x 204.0 x 433.0 mm (After folding the Stand)
Weight
6.7kg (With Basic Stand)
VESA Mounting Interface
100mm x 100mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 153S
General
Size
15.0 inch diagonal
304.1 (H) x 228.1 (V)
0.297 (H) x 0.297 (V)
a-si TFT active matrix
140/115(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 61 kHz
56 ~ 75 Hz
Vertical
Display Color
16,194,277 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1024 x 768@60Hz
1024 x 768@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite, Sync-on-Green
TTL level positive or negative
Maximum Pixel Clock
80 MHz
Power Supply
AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz
Signal Cable
15pin to 15pin D-sub cable, Detachable
Power Consumption
32W (Maximum)
Dimensions (WxDxH) / Weight
353.0 x 152 x 350.0 mm / 3.8kg
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the number of TFT LCD pixels that is contained in this product are 2,359,296.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 173S
General
Size
17.0 inch diagonal
337.92 (H) x 270.336 (V)
0.264 (H) x 0.264 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,194,277
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite, SOG
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
40W (Maximum)
Dimensions (WxDxH) / Weight
382.0 x 177.0 x 392.5 mm / 5.1kg
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 153B
General
Size
15.0 inch diagonal
304.1 (H) x 228.1 (V)
0.297 (H) x 0.297 (V)
a-si TFT active matrix
140/115(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 61 kHz
56 ~ 75 Hz
Vertical
Display Color
16,194,277 Colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1024 x 768@60Hz
1024 x 768@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite, Sync-on-Green
TTL level positive or negative
Maximum Pixel Clock
80 MHz
Power Supply
AC 90 ~ 264 VAC, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
36W (Maximum)
Dimensions (WxDxH) / Weight
353.9 x 152 x 360.0 mm / 3.8kg
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
Download from Www.Somanuals.com. All Manuals Search And Download.
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the number of TFT LCD pixels that is contained in this product are 2,359,296.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
General
Model Name
LCD Panel
SyncMaster 173B
General
Size
17.0 inch diagonal
337.92 (H) x 270.336 (V)
0.264 (H) x 0.264 (V)
a-si TFT active matrix
140/120(H/V)
PowerSaver
Preset Timing
Modes
Display area
Pixel Pitch
Type
Viewing Angle
Synchronization
Horizontal
31 ~ 81 kHz
56 ~ 75 Hz
Vertical
Display Color
16,194,277 colors
Resolution
Optimum resolution
Maximum resolution
Input Signal, Terminated
1280 x 1024@60Hz
1280 x 1024@75Hz
RGB Analog 0.7 Vpp positive at 75 ohms
Separate H/V sync, Composite, Sync-on-Green
TTL level positive or negative
Maximum Pixel Clock
135 MHz
Power Supply
AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable
Power Consumption
42W (Maximum)
Dimensions (WxDxH) / Weight
382.0 x 177.0 x 435.0 mm / 4.9kg
VESA Mounting Interface
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F(10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
Download from Www.Somanuals.com. All Manuals Search And Download.
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of
99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality
and you can use it without uneasiness.
z
For example, the number of TFT LCD pixels that is contained in this product are 2.359.296.
Note: Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/152V/153S
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Max 2W
Power Indicator
Green
Black
Power Consumption
Max 32.0W
Max 1W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product
®
meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153B
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Max 2W
Power Indicator
Green
Black
Power Consumption
Max 36.0W
Max 1W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product
®
meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 173V/172V/173S
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Max 2W
Power Indicator
Green
Black
Power Consumption
Max 40.0W
Max 1W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product
®
meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 173B
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Max 2W
Power Indicator
Green
Black
Power Consumption
Max 42.0W
Max 1W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product
®
meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 193V/192V
This monitor has a built-in power management system called PowerSaver. This system saves
energy by switching your monitor into a low-power mode when it has not been used for a certain
amount of time. The monitor automatically returns to normal operation when you move the
computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF
when it is not needed, or when leaving it unattended for long periods. The PowerSaver system
operates with a VESA DPMS compliant video card installed in your computer. Use a software utility
installed on your computer to set up this feature.
General
PowerSaver
Preset Timing
Modes
Power saving mode
State
Normal Operation
Power Switch off
EPA/ENERGY 2000
Green, Blinking
Max 2W
Power Indicator
Green
Black
Power Consumption
Max 45.0W
Max 1W
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant
when used with a computer equipped with VESA DPMS functionality.
®
As an ENERGY STAR Partner, SAMSUNG has determined that this product
®
meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153V/152V
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
General
PowerSaver
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
Preset Timing
Modes
IBM, 640 x 350
31,469
31,469
31,469
37,500
37,861
35,156
37,879
46,875
48,077
48,363
56,476
60,023
70,086
59,940
70,087
75,000
72,809
56,250
60,317
75,000
72,188
60,004
70,069
75,029
25,175
25,175
28,322
31,500
31,500
36,000
40,000
49,500
50,000
65,000
75,000
78,750
+/-
-/-
IBM, 640 x 480
IBM, 720 x 400
-/+
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
-/-
-/-
+,-/+,-
+/+
+/+
+/+
-/-
-/-
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 173V/172V/193V/192V
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
General
PowerSaver
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
Preset Timing
Modes
IBM, 640 x 350
31,469
31,469
31,469
37,500
37,861
35,000
49,726
35,156
37,879
46,875
48,077
48,363
56,476
60,023
63,981
79,976
70,086
59,940
70,087
75,000
72,809
66,667
74,551
56,250
60,317
75,000
72,188
60,004
70,069
75,029
60,020
75,025
25,175
25,175
28,322
31,500
31,500
30,240
57,284
36,000
40,000
49,500
50,000
65,000
75,000
78,750
108,00
135,00
+/-
-/-
IBM, 640 x 480
IBM, 720 x 400
-/+
VESA, 640 x 480
VESA, 640 x 480
MAC,, 640 x 480
MAC,, 832 x 624
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 1024
VESA, 1280 x 1024
-/-
-/-
-/-
-/-
+,-/+,-
+/+
+/+
+/+
-/-
-/-
+/+
+/+
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 173S/173B
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
General
PowerSaver
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
Preset Timing
Modes
IBM, 640 x 350
31,469
31,469
31,469
35,000
49,726
37,500
37,861
35,156
37,879
46,875
48,077
48,363
56,476
60,023
63,981
79,976
81,129
70,086
59,940
70,087
66,667
74,551
75,000
72,809
56,250
60,317
75,000
72,188
60,004
70,069
75,029
60,020
75,025
76,106
25,175
25,175
28,322
30,240
57,284
31,500
31,500
36,000
40,000
49,500
50,000
65,000
75,000
78,750
108,00
135,00
135,00
+/-
-/-
IBM, 640 x 480
IBM, 720 x 400
-/+
-/-
MAC, 640 x 480
MAC, 832 x 624
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 1024
VESA, 1280 x 1024
SUN, 1280 x 1024
-/-
-/-
-/-
+,-/+,-
+/+
+/+
+/+
-/-
-/-
+/+
+/+
+/+
-/-
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
SyncMaster 153S/153B
If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
General
PowerSaver
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
Display Mode
Preset Timing
Modes
IBM, 640 x 350
31,469
31,469
31,469
35,000
49,726
37,500
37,861
35,156
37,879
46,875
48,077
48,363
56,476
60,023
70,086
59,940
70,087
66,667
74,551
75,000
72,809
56,250
60,317
75,000
72,188
60,004
70,069
75,029
25,175
25,175
28,322
30,240
57,284
31,500
31,500
36,000
40,000
49,500
50,000
65,000
75,000
78,750
+/-
-/-
IBM, 640 x 480
IBM, 720 x 400
-/+
-/-
MAC, 640 x 480
MAC, 832 x 624
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
-/-
-/-
-/-
+,-/+,-
+/+
+/+
+/+
-/-
-/-
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of
the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S.A. :
Samsung Computer Products Customer Service
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856
Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864)
Fax. : (973)601-6001
Service
Terms
Regulatory
Natural Color
For Better Display
Authority
BRAZIL :
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421
CANADA :
Samsung Electronics Canada Inc.
7037 Financial Drive
Mississauga, Ontario L5N 6R3
Tel. : 1-800-SAMSUNG (1-800-726-7864)
Fax. : (905) 542-1199
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
e-mail : soporte@samsung-latin.com
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
PERU
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
GERMANY :
TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0,12/MIN.
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑA :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
THAILAND :
HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel +46 8 590 966 00
Fax +46 8 590 966 50
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
o
Rua Mário Dioniso, N 2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Download from Www.Somanuals.com. All Manuals Search And Download.
Free Line 800 220 120
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
MEXICO :
Samsung Electronics Mexico S.A. de C.V.
Saturno 44 Col. Nueva Industrial Vallejo
Del. Gustavo A. Madero C.P. 07700
Mexico D.F.
Tel. 01 57 47 51 00
Fax. 01 57 47 52 02
RFC: SEM950215S98
IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO S.A. DE C.V.
SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO
DEL. GUSTAVO A. MADERO C.P. 07700
MEXICO D.F. TEL. 5747-5100
RFC: SEM950215S98
EXPORTADO POR: SAMSUNG ELECTRONICS CO.,LTD.
JOONG-ANG DAILY NEWS BLDG.
7 SOON-WHA-DONG CHUNG-KU,
C.P.O BOX 2775, 1144 SEOUL, KOREA
Download from Www.Somanuals.com. All Manuals Search And Download.
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'.
Unit: mm
Service
Vertical Frequency
Terms
The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh
Rate. Unit: Hz
Regulatory
Natural Color
For Better Display
Authority
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this
case, flickering of the screen can be detected. To avoid this problem, there is a
Flicker-free Mode using a vertical frequency over 70 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is
called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the Non-
Interlace method while showing odd lines and then even lines in turn is called the Interlace
method. The Non-Interlace method is used for the majority of monitors to ensure a clear image.
The Interlace method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and
the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.
Example: If the resolution is 1280 X 1280, this means the screen is composed of 1280
horizontal dots (horizontal resolution) and 1280 vertical lines (vertical resolution).
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Terms
Regulatory
Natural Color
For Better Display
Authority
FCC Information
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the
following warning:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television receptions, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
z
z
z
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
z
User Information
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment. If necessary, consult your dealer or an
experienced radio/television technician for additional suggestions. You may find the booklet called
How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared
by the Federal Communications Commission. It is available from the U.S. Government Printing
Office, Washington, DC 20402, Stock Number 004-000-00345-4.
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Tel) 949-975-7310
Fax) 949-922-8301
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It
may be suitable for connection to any UL Listed personal computer with similar configuration.
Before making the connection, make sure the voltage rating of the computer convenience outlet is
the same as the monitor and that the ampere rating of the computer convenience outlet is equal to
or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-
15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable
power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.
IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations of ICES-003.
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les
Download from Www.Somanuals.com. All Manuals Search And Download.
équipements produisant des interférences au Canada.
MPR II Compliance
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic
fields.
European Notice(Europe Only)
Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC),
(93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the
European Community.
Compliance with these directives implies conformity to the following European Norms:
z
z
z
z
EN55022:1998+A1:2000 - Radio Frequency Interference
EN55024:1998 - Electromagnetic Immunity of Information Technology Equipment
EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics
EN61000-3-3:1995 - Voltage Fluctuations
PCT Notice
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in
a domestic environment, it may cause radio interference. Install and use the equipment according
to the instruction manual.
TCO'95-Ecological requirements for personal computers (TCO applied model only)
AB general requirements
AB2 Written Eco-document acompanying the products
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice
has provided you with a product developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and to the further development of
environmentally-adapted electronic products.
Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment.The main problem as far as monitors and
other electronic equipment are concerned is that environmentally harmful substances are used
Download from Www.Somanuals.com. All Manuals Search And Download.
both in the products and during their manufacture. Since it has not been possible so far for the
majority of electronic equipment to be recycled in a satisfactory way, most of these potentially
damaging substances sooner or later enter Nature.
There are also other characteristics of a monitor, such as energy consumption levels, that are
important from both the working and natural environment viewpoints. Since all types of
conventional electricity generation have a negative effect on the environment (acidic and climate-
influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment
in offices consumes an enormous amount of energy, since it is often routinely left running
continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme, which provides for international
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the
TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and
Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern among other things restrictions on the presence and use of
heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated
solvents. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan, which must be adhered to in each country where the company conducts its
operations policy. The energy requirements include a demand that the monitor after a certain
period of inactivity shall reduce its power consumption to a lower level, in one or more stages. The
length of time to reactivate the monitor shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example in respect of the
reduction of electric and magnetic fields, along with physical and visual ergonomics and good
usability.
TCO Development Unit 1996-11-29
On the page this folder you will find a brief summary of the environmental requirements met by
this product.
The complere environmental criteria document may be ordered from:
TCO Development Unit
S-11494 Stockholm
Sweden
Fax: +46 8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO'95-approved and labelled products may also
be obtained via the Internet, using the address:
TCO'95 is a co-operative project between(3 logos)
Environmental Requirements
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and
housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer
casing can consist of flame retardant substances. These are related to another group of
environmental toxins, PCBs, which are suspected to give rise to similar harm, including
reproductive damage in fish eating birds and mammals, due to the bioaccumulative processes.
Flame retardants have been found in human blood and researchers fear that disturbances in
foetus development may occur.
z
TCO'95 demand requires that plastic components weighing more than 25 grams must not
contain organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been
developed.
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous
system and is toxic in high doses.
Download from Www.Somanuals.com. All Manuals Search And Download.
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of mercury. It also demands that no mercury is present in any of the electrical or electronics
components concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in
the stratosphere, causing increased reception on Earth of ultraviolet light with consequent
increased risks of skin cancer (malignant melanoma).
z
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the
manufacturing of the product or its packaging.
TCO'99-Ecological requirements for personal computers (TCO applied model only)
Congratulations!
You have just purchased a TCO'99 approved and labelled product! Your choice has provided you
with a product developed for professional use. Your purchase has also contributed to reducing the
burden on the environment and also to the further development of environmentally adapted
electronics products.
This product meets the requirements for the TCO'99 scheme which provides for an international
environmental and quality labelling labelling of personal computers. The labelling scheme was
developed as a joint effort by the TCO(The Swedish Confederation of Professional Employees),
Svenska Naturskyddsforeningen(The Swedish Society for Nature Conservation), Statens
Energimyndighet(The Swedish National Energy Administration) and SEMKO AB.
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of
electric and magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment. The main problem, as far as computers
and other electronics equipment are concerned, is that environmentally harmful substances are
used both in the products and during their manufacture. Since it is not so far possible to
satisfactorily recycle the majority of electronics equipment, most of these potentially damaging
substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics
equipment in offices is often left running continuously and thereby consumes a lot of energy.
What does labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The
Swedish Society for Nature Conservation). These demands impose restrictions on the presence
and use of heavy metals, brominated and chlorinated flame retardants, CFCs(freons)and
chlorinated solvents, among other things. The product must be prepared for recycling and the
manufacturer is obliged to have an environmental policy which must be adhered to in each
country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The
length of time to reactivate the computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The
complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Download from Www.Somanuals.com. All Manuals Search And Download.
Current information regarding TCO'99 approved and labelled products may also be obtained via
the Internet, using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their
purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer
casing can consist of flame retardant substances. Most flame retardants contain bromine or
chloride, and those flame retardants are chemically related to another group of environmental
toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are
suspected of giving rise to severe health effects, including reproductive damage in fish-eating
birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found
in human blood and researchers fear that disturbances in foetus development may occur.
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams
must not contain flame retardants with organically bound bromine or chlorine. Flame retardants
are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses. The
relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens
and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and
is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any
mercury. It also demands that mercury is not present in any of the electrical or electronics
components associated with the labelled unit. There is however one exception. Mercury is, for the
time being, permitted in the back light system of flat panel monitors as today there is no
commercially available alternative. TCO aims on removing this exception when a Mercury free
alternative is available.
CFCs (freons)
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed
circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere,
causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer
(malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement
permits the inclusion of lead since no replacement has yet been developed.
Medical Requirement
Classifications:
In accordance with UL 2601-1/IEC 60601-1, the product is cssified as Continuous duty Class I
equipment, which is not protected against ingress of liquids. The product is not suitable for use in
the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide.
EMC
This equipment has been tested and found to comply with the limits for medical devices to the IEC
601-1-2:1994. These limits are designed to provide reasonable protection against harmful
interference in a typical medical installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to other devices in the vicinity. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to other devices, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
z
Reorient or relocate the receiving device.
Download from Www.Somanuals.com. All Manuals Search And Download.
z
z
Increase the separation between the equipment.
Connect the equipment into an outlet on a circuit different from that to which the other device
(s) are connected.
z
Consult the manufacturer or field service technician for help.
Video In / RS 232 / Video Out
Accessories equipment connected to the analog and digital interfaces must be certified to the
respective IEC standards (i.e. IEC 950 for data processing equipment and IEC 601-1 for medical
equipment.) Furthermore all configurations shall comply with the system standard IEC 601-1-1.
Everybody who connects additional equipment to the signal input part or signal output part
configures a medical system, and is therefore, responsible that the system complies with the
requirements of the system standard IEC 601-1-1. If in doubt, consult the technical services
department or your local representative.
Transport and Storage Limitations:
Temperature Range of -40°C to +70°C
Relative Humidity of 10 -95%, non-condensing
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Download from Www.Somanuals.com. All Manuals Search And Download.
Natural Color Software Program
Service
Terms
Regulatory
Natural Color
For Better Display
Authority
One of the recent problems in using a computer is that the color of the images printed out by a
printer or other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI). This system is available only for Samsung monitors and makes the
color of the images on the monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial
screen of the program installation will be executed. Click Natural Color on the initial screen to
install the Natural Color software. To install the program manually, insert the CD included with
the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then
select [Execute].
Enter D:\color\eng\setup.exe and then press the <Entrer> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a
program].
Select Natural Color from the list and then click the [Add/Delete] button.
Download from Www.Somanuals.com. All Manuals Search And Download.
For Better Display
1. Adjust computer resolution and screen injection rate (refresh rate) in control panel of
computer as described below to enjoy the best quality of picture. You can have an uneven
quality of picture in the screen if the best quality of picture is not provided in TFT-LCD.
Service
Terms
Regulatory
Natural Color
{
{
Resolution: 1280 x 1024
Vertical frequency (refresh rate): 60 Hz
For Better
Display
Authority
2. TFT LCD panel manufactured by using advanced semiconductor technology with
precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE
and WHITE color seem to be bright sometimes or some of black pixels could be seen.
This is not from bad quality and you can use it without uneasiness.
{
For example, the number of TFT LCD pixels that is contained in this product are
3,932,160.
3. When you clean the monitor and the panel outside, please apply the recommended small
amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced
but to be scrubbed out softly. If excessive force is applied, you can have a stain on it.
4. If you are not satisfied with the quality of picture, you can get better quality of picture by
executing "auto adjustment function" in display screen that is appeared as window
termination button is pressed. If there's still noise after automatic adjustment, use
FINE/COARSE adjustment function.
5. If you view a fixed screen for an extended period of time, residual image or blurriness may
appear.
Change the mode to energy save or set a screensaver to moving picture when you need
to be away from the monitor for an extended period of time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Information in this document is subject to change without notice.
© 2003 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.
Service
Terms
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Regulatory
Natural Color
For Better Display
Authority
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an
ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets
the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein
may be the trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Radio Shack Scanner Pro 71 User Guide
RCA CRT Television J13805CL User Guide
RCA TV VCR Combo T09082 User Guide
Remington Electric Shaver TA 4570 User Guide
Renesas Computer Hardware H8S 2169 Series User Guide
Ricoh Printer L4130 User Guide
Roadmaster GPS Receiver VRBT120P User Guide
Russell Hobbs Microwave Oven RHM2011 User Guide
Sears Air Compressor 91972197 User Guide
SEH Computertechnik Printer TPG60 User Guide