Samsung Computer Monitor 151X User Guide

SyncMaster 151x  
Install drivers  
Install programs  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not use a damaged or loose plug.  
This may cause an electric shock or fire.  
z
Do not pull the plug out by the wire nor touch the plug with wet hands.  
This may cause an electric shock or fire.  
z
Use only a properly grounded plug and receptacle.  
An improper ground may cause electric shock or equipment damage.  
z
Insert the power plug firmly so that it does not come loose.  
A bad connection may cause fire.  
z
Do not excessively bend the plug and wire nor place heavy objects upon  
them, which could cause damage.  
z
This may cause an electric shock or fire.  
Do not connect too many extension cords or plugs to an outlet.  
This may cause fire.  
z
Installation  
Be sure to contact an authorized Service Center when installing your set in a  
location with heavy dust, high or low temperatures, high humidity, and  
chemical substances, or where it will be operated for 24 hours continuously  
such as an airport, train station or etc.  
Failure to do so may cause serious damage to your set.  
Put your monitor in a location with low humidity and a minimum of dust.  
z
Failure to do so may cause an electric shock or fire inside the monitor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not drop the monitor when moving it.  
This may cause damage to the product or human body.  
z
Install the monitor base in a showcase or shelf so that the end of the  
base does not project beyond the showcase or shelf.  
z
Dropping the product may cause damage to the product or personal  
injury.  
Do not place the product on an unstable or small surface area.  
z
Place the product on an even, stable surface, as the product may fall  
and cause harm to someone walking by, specifically children.  
Do not place the product on the floor.  
Someone, specifically children could trip over it.  
z
Keep any flammable objects such as candles, insecticides or cigarettes  
away from the product.  
z
Otherwise, this may cause a fire.  
Keep any heating devices away from the power cable.  
A melted coating may lead to electric shock or fire.  
z
Do not install the product in places with poor ventilation, for instance, a  
bookshelf, closet, etc.  
z
Any increase in internal temperature may cause fire.  
Set down the monitor carefully.  
The monitor could be damaged or broken.  
z
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not place the monitor face down.  
The TFT-LCD surface may be damaged.  
z
Installing a wall bracket must be done by a qualified professional.  
z
z
Installation by unqualified personnel may result in injury.  
Always use the mounting device specified in the owner's manual.  
When installing the product, make sure to keep it away from the wall  
(more than 10cm/4inch ) for ventilation purposes.  
z
Poor ventilation may cause an increase in the internal temperature of  
the product, resulting in a shortened component life and degraded  
performance.  
Clean  
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with  
a slightly moistened, soft fabric.  
Do not spray water or detergent directly on the monitor.  
z
This may cause damage, electric shock or fire.  
Use the recommended detergent with a smooth cloth.  
If the connector between the plug and the pin is dusty or dirty, clean it  
properly with a dry cloth.  
z
A dirty connector may cause an electric shock or fire.  
Make sure to unplug the power cord before cleaning the product.  
Otherwise, this may cause electric shock or fire.  
z
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unplug the power cord from the power outlet and wipe the product using  
a soft, dry cloth.  
z
Do not use any chemicals such as wax, benzene, alcohol, thinners,  
insecticide, air freshener, lubricant or detergent.  
Contact the Service Center or Customer Center for interior cleaning  
once a year.  
z
Keep the product's interior clean. Dust which has accumulated in the  
interior over an extended period of time may cause malfunction or fire.  
Others  
Do not remove cover (or back).  
z
z
This may cause an electric shock or fire.  
Refer servicing to qualified service personnel.  
If your monitor does not operate normally - in particular, if there are any  
unusual sounds or smells coming from it - unplug it immediately and  
contact an authorized dealer or service.  
z
This may cause an electric shock or fire.  
Keep the product away from places exposed to oil, smoke or moisture;  
do not install inside a vehicle.  
z
z
This may cause malfunction, an electric shock or fire.  
Especially avoid operating the monitor near water or outdoors where the  
monitor could be exposed to snow or rain.  
If the monitor is dropped or the casing is damaged, turn the monitor off  
and unplug the power cord. Then contact the Service Center.  
z
The monitor may malfunction, causing an electric shock or fire.  
Disconnect the plug from the outlet during storms or lightening or if it is  
not used for a long period of time.  
z
Failure to do so may cause an electric shock or fire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not try to move the monitor by pulling only the wire or the signal  
cable.  
z
This may cause a breakdown, electric shock or fire due to damage to  
the cable.  
Do not move the monitor right or left by pulling only the wire or the  
signal cable.  
z
This may cause a breakdown, electric shock or fire due to damage to  
the cable.  
Do not cover the vents on the monitor cabinet.  
Bad ventilation may cause a breakdown or fire.  
z
Do not place water containers, chemical products or small metal objects  
on the monitor.  
z
z
This may cause malfunction, an electric shock or fire.  
If a foreign substance enters the monitor, unplug the power cord and  
contact the Service Center .  
Keep the product away from combustible chemical sprays or  
inflammable substances.  
z
This may cause an explosion or fire.  
Never insert anything metallic into the monitor openings.  
This may cause an electric shock, fire or injury.  
z
Do not insert metal objects such as chopsticks, wire and gimlet or  
inflammable objects such as paper and match into the vent, headphone  
port or AV ports.  
z
It may cause a fire or an electric shock. If an alien substances or water  
flows into the product, turn the product off, unplug the power connector  
from the wall outlet and contact Service Center.  
If you view a fixed screen for an extended period of time, residual image  
or blurriness may appear.  
z
Change the mode to energy save or set a screensaver to moving  
picture when you need to be away from the monitor for an extended  
period of time.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjust the resolution and frequency to the levels appropriate for the  
model.  
z
Inappropriate resolution may cause undesirable picture quality.  
15 inch - 1024 X 768  
Be careful that adapter should not be in contact with water and  
therefore not be wet.  
z
z
This may cause malfunction, an electric shock or fire.  
Do not use adapter by the waterside or outside particularly when it rains  
or snows.  
z
Be careful that adapter should not be wet while cleaning floor with  
water.  
Keep all power adapters apart.  
Failure to do so may cause fire.  
z
Keep power adapter away from any other heat source.  
Failure to do so may cause fire.  
z
Remove and discard vinyl bag from power adapter before use.  
Failure to do so may cause fire.  
z
Always keep power adapter in well-ventilated area.  
Watching the monitor continuously at a too close angle may result in  
eyesight damage.  
To ease eye strain, take at least a five-minute break after every hour of  
.
using the monitor  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not install the product on an unstable, uneven surface or a location  
prone to vibrations.  
z
Dropping the product may cause damage to the product or personal  
injury. Using the product in a location prone to vibrations may shorten  
the lifetime of the product or may catch fire.  
When moving the monitor, turn off and unplug the power cord.  
Make sure that all cables, including the antenna cable and cables  
connected to other devices, are disconnected before moving the  
monitor.  
z
Failure to disconnect a cable may damage it and lead to fire or an  
electric shock.  
Place the product out of children's reach, as they could damage it by  
hanging onto it.  
z
A falling product could cause physical damage even death.  
When not using the product for an extended time period, keep the  
product unplugged  
z
Otherwise, this may cause heat emission from the accumulated dirt or  
degraded insulation, leading to electric shock or fire.  
Do not place children's favorite objects (or anything else that may be  
tempting) on the product.  
z
Children may try to climb on the product to retrieve an object. The  
product could fall, causing physical damage or even death.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Please make sure the following items are included with your monitor.  
If any items are missing, contact your dealer.  
Contact a local dealer to buy optional items.  
Unpacking  
Monitor  
Manual  
User's Guide,  
Monitor Driver,  
Natural Color software,  
MagicTune™ software,  
Warranty Card  
(Not available in all  
locations)  
Quick Setup Guide  
Cable  
D-Sub Cable  
Power Cord  
DC-Adapter  
Bracket  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VESA Mounting Bracket  
Front  
Use this button to auto adjustment direct access.  
Auto button  
Use this button to Exit the active menu or the OSD.  
/ Exit button  
Menu button  
Use this button to open the OSD and activate a highlighted menu  
item.  
Use this button for turn the monitor on and off.  
Power button  
This light glows green during normal operation, and blinks green  
once as the monitor saves your adjustments.  
Power indicator  
MagicBright is a new feature providing optimum viewing  
environment depending on the contents of the image you are  
watching. Currently three different modes are available: Text,  
Internet, and Entertain. Each mode has its own pre-configured  
brightness value. You can easily select one of three settings by  
simply pressing MagicBright control buttons.  
MagicBright button  
[
]
1) User Adjusted  
Although the values are carefully chosen by our engineers, the  
pre-configured values may not be comfortable to your eyes  
depending on your taste.  
If this is the case, adjust the brightness and contrast by using  
the OSD menu.  
: Normal brightness  
2) Text  
For documentations or works involving heavy text.  
: Medium brightness  
3) Internet  
For working with a mixture of images such as text and  
graphics.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
: High brightness  
4) Entertain  
For watching motion pictures such as a DVD or VCD.  
>>Click here to see an animation clip  
These buttons allow you to highlight and adjust items in the menu.  
Adjust buttons [- / +]  
See PowerSaver described in the manual for further information regarding power saving  
functions. For energy conservation, turn your monitor off when it is not needed, or when  
leaving it unattended for long periods.  
Rear  
(The configuration at the back of the monitor may vary from product to product.)  
Connect the DC Adapter for your monitor to the power port on the  
back of the monitor.  
Power port  
Connect the signal cable to the 15-pin, D-sub connector on the back  
of your monitor  
D-sub 15-pin port  
See Connecting the Monitor for further information regarding cable connections.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connect the DC Adapter for your monitor to the power port on the back of the monitor.  
Plug the power cord for the monitor into a nearby outlet.  
1.  
2.  
Using the D-sub (Analog) connector on the video card.  
Connect the D-sub cable to the 15-pin, D-sub connector on the back of your monitor.  
Connected to a Macintosh.  
Connect the monitor to the Macintosh computer using the D-sub connection cable.  
3.  
4.  
5.  
In the case of an old model Macintosh, you need to connect the monitor using a special Mac  
adapter.  
Turn on your computer and monitor. If your monitor displays an image, installation is  
complete.  
Wall Mounting the Monitor  
Download from Www.Somanuals.com. All Manuals Search And Download.  
As shown in the figure above, you first fold the stand. You attach the VESA mounting brackets on  
the wall. You hang the monitor aligning its bottom grove with the bracket.  
Attaching a base  
NOTE: This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.  
Squeeze the folded monitor stand into the VESA mounting bracket. Then fasten it using four  
supplied nuts with the monitor, mounting pad and VESA mounting bracket aligned.  
1. VESA Mounting Brkt  
2. Mounting interface pad  
Installing the Monitor Driver (Automatic)  
When prompted by the operating system for the monitor driver, insert the CD-ROM  
included with this monitor. Driver installation is slightly different from one operating  
system to another. Follow the directions appropriate for the operating system you  
have.  
Prepare a blank disk and download the driver program file at the Internet web site shown  
here.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
z
Internet web site :  
Windows ME  
1. Insert CD into the CD-ROM drive.  
2. Click  
.
"Windows ME Driver"  
3. Choose your monitor model in the model list, then click the  
button.  
"OK"  
4. Click the  
button in the  
window.  
"Warning"  
"Install"  
5. Monitor driver installation is completed.  
Windows XP/2000  
1. Insert CD into the CD-ROM drive.  
2. Click  
"Windows XP/2000 Driver"  
3. Choose your monitor model in the model list, then click the  
button.  
"OK"  
4. If you can see following message window, then click the  
button.  
"Continue Anyway"  
Then click  
button.  
"OK"  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This monitor driver is under certifying MS logo,and this installation don't  
damage your system.The certified driver will be posted on Samsung  
Monitor Homepage  
5. Monitor driver installation is completed.  
Installing the Monitor Driver (Manual)  
Windows XP | Windows 2000 |Windows Me |Windows NT | Linux  
When prompted by the operating system for the monitor driver, insert the CD-ROM  
included with this monitor. Driver installation is slightly different from one operating  
system to another. Follow the directions appropriate for the operating system you  
have.  
Prepare a blank disk and download the driver program file at the Internet web site shown  
here.  
z
Internet web site :  
®
®
Microsoft Windows XP Operating System  
1. Insert CD into the CD-ROM driver.  
2. Click "  
" —> "  
" then click the "  
" icon.  
Appearance and Themes  
Start  
Control Panel  
3. Click "  
" icon and choose the "  
" tab then click "  
".  
Advanced..  
Display  
Settings  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Click the "  
" button on the "  
" tab and select "  
Monitor  
" tab.  
Driver  
Properties  
5. Click "  
" and select "  
" then click "  
" button.  
Next  
Update Driver..  
Install from a list or..  
6. Select "  
" then click "  
" and then click "  
Next  
".  
Have disk  
Don't search ,I will..  
7. Click the "  
" button then choose A:(D:\Driver) and choose your monitor model in the  
Browse  
model list and click the "  
" button.  
Next  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. If you can see following "  
" window, then click the " " button. Then  
Continue Anyway  
Message  
click "  
" button.  
OK  
This monitor driver is under certified MS logo,and this installation doesn't damage your  
system.The certified driver will be posted on Samsung Monitor homepage.  
9. Click the "  
" button then click "  
" button continually.  
OK  
Close  
10. Monitor driver installation is completed.  
®
®
Microsoft Windows 2000 Operating System  
When you can see "Digital Signature Not Found" on your monitor, follow these steps.  
1. Choose "  
" button on the "  
Browse  
" window.  
OK  
2. Click the "  
Insert disk  
" button on the "  
" window.  
File Needed  
3. Choose A:(D:\Driver) then click the "Open" button and then click "  
" button.  
OK  
How to install  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Click "  
2. Double click the "  
3. Choose the "  
4. Choose "  
" , "  
" , "  
".  
Control Panel  
Start  
Setting  
Display  
" tab and then click "  
" Icon.  
".  
Advanced..  
Settings  
".  
Monitor  
Case1:If the "Properties" button is inactive, it means your monitor is properly configured.  
Please stop installation  
Case2:If the "Properties" button is active, click the "Properties" button then follow next steps  
continually.  
5. Click "  
6. Choose "  
" and then click on "  
" then click on the "Next" button.  
Driver  
Update Driver..  
Display a list of the known drivers for this device so that I can choose a  
" then click "  
" and then click "  
".  
specific driver  
7. Click the "  
8. Click the "  
Next  
Have disk  
" button then choose A:(D:\Driver).  
Browse  
" button, then click " " button.  
Open  
OK  
9. Choose your monitor model and click the "  
" button then click "  
" button.  
Next  
Next  
10. Click the "  
" button then the "  
Finish  
" button.  
Close  
If you can see the "  
" window then click the "  
Digital Signature Not Found  
"button.  
Yes  
And click the "  
" button then the "  
" button.  
Close  
Finish  
®
®
Microsoft Windows Millennium Operating System  
1. Click "  
" , "  
Display  
" , "  
".  
Start  
2. Double click "  
Setting  
" icon.  
Control Panel  
3. Select the "  
4. Select the "  
" tab and click "  
" tab.  
" button.  
Advanced Properties  
Settings  
Monitor  
5. Click the "  
" button in the "  
" area.  
Change  
Monitor Type  
".  
6. Choose "  
7. Choose "  
Specify the location of the driver  
Display a list of all the driver in a specific location..  
" button  
" then click "  
" button.  
Next  
8. Click the "  
Have Disk  
9. Specify A:\(D:\driver) then click "  
" button.  
OK  
" and choose the monitor that corresponds to the one you  
10. Select "  
Show all devices  
connected to your computer and click "  
".  
OK  
" button and "  
11. Continue choosing "  
dialogue box.  
" button until you close the Display Properties  
Close  
OK  
®
®
Microsoft Windows NT Operating System  
1. Click  
,
,
, and then double-click  
icon.  
Display  
Start Settings Control Panel  
2. In Display Registration Information window, click Settings Tab and then click  
All Display  
.
Modes  
3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)  
and then click  
.
OK  
button if you see the screen working normally after clicking  
4. Click  
. If the screen is  
Apply  
not normal, change to a different mode (lower mode of resolution, colors or frequency).  
If there is no Mode at , select the level of resolution and vertical  
Test  
All Display Modes  
frequency by referring to the Preset Timing Modes in the user guide.  
Linux Operating System  
To execute X-Window, you need to make the X86Config file, which is a type of system setting file.  
1. Press Enter at the first and the second screen after executing the X86Config file.  
2. The third screen is for  
setting your mouse  
3. Set a mouse for your computer.  
.
4. The next screen is for  
.
selecting a keyboard  
5. Set a keyboard for your computer.  
6. The next screen is for  
.
setting your monitor  
for your monitor. (You can enter the frequency  
7. First of all, set a  
directly.)  
horizontal frequency  
8. Set a  
for your monitor. (You can enter the frequency directly.)  
vertical frequency  
9. Enter the  
. This information will not affect the actual execution  
model name of your monitor  
of X-Window.  
10. You have  
setting up your monitor.  
finished  
X-Window after setting other requested hardware.  
Execute  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Natural Color  
Natural Color Software Program  
One of the recent problems in using a computer is that the color of the images printed out by a  
printer or other images scanned by a scanner or a digital camera are not the same as those  
shown on the monitor.  
The Natural Color S/W is the very solution for this problem. It is a color administration system  
developed by Samsung Electronics in association with Korea Electronics &  
Telecommunications Research Institute (ETRI).  
This system is available only for Samsung monitors and makes the color of the images on the  
monitor the same as the printed or scanned images.  
For more information, refer to Help (F1) in the software program.  
How to install the Natural Color software  
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial  
screen of the program Natural Color will be executed. Click Natural Color on the initial screen  
to install the Natural Color software.  
To install the program manually, insert the CD included with the Samsung monitor into the CD-  
ROM Drive, click the [Start] button of Windows and then select [Execute].  
Enter D:\color\eng\setup.exe and then press the <Enter> key.  
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)  
How to delete the Natural Color software program  
Select  
program"  
on the  
menu and then double-click  
"Start" "Add/Delete a  
"Setting/Control Panel"  
.
Select Natural Color from the list and then click the  
button.  
"Add/Delete"  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUTO  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
AUTO  
Description  
When the '  
' button is pressed, the Auto Adjustment screen appears  
as shown in the animated screen on the center.  
Auto adjustment allows the monitor to self-adjust to the incoming video  
signal. The values of fine, coarse and position are adjusted automatically.  
AUTO  
To make the automatic adjustment function sharper, execute the 'AUTO'  
function while the AUTO PATTERN is on.  
z
z
If Auto Adjustment does not work properly, press Auto button again to  
adjust picture with more accuracy.  
If you change resolution in the control panel, Auto function will be  
executed automatically.  
OSD Lock & Unlock  
Menu  
Description  
After push the "MENU" button more than 5 seconds, OSD function is  
locked (unlocked).  
OSD Lock & Unlock  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MagicBright™  
Menu  
Description  
Then push the MagicBright button again to circle through available  
preconfigured modes.  
MagicBright™  
- four different modes(User Adjusted/Text/Internet/Entertain)  
Menu  
Description  
You can use the on-screen menus to change the brightness according to  
personal preference.  
Brightness  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
You can use the on-screen menus to change the contrast according to  
personal preference.  
Contrast  
Image Lock  
Menu  
Fine  
Description  
Play/Stop  
Removes noise such as horizontal stripes. If the noise  
persists even after Fine tuning, repeat it after adjusting the  
frequency (clock speed).  
Removes noise such as vertical stripes. Coarse  
adjustment may move the screen image area. You may  
relocate it to the center using the Horizontal Control menu.  
Coarse  
Position  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
Play/Stop  
Follow these instructions to change the horizontal position  
of the monitor's entire display.  
H-Position  
Follow these instructions to change the vertical position of  
the monitor's entire display.  
V-Position  
Reset  
Menu  
Description  
Play/Stop  
Geometry parameters are replaced with the factory default  
values.  
Geometry Reset  
Color parameters are replaced with the factory default  
values.  
Color Reset  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
Color temperature is a measure of the "warmth"of the image colors.  
Color Temperature  
Menu  
Description  
Adjusts individual R,G,B color balance.  
Color Control  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
You can choose one of the seven languages.  
Language  
:The language chosen affects only the language of the OSD. It has no  
Note  
effect on any software running on the computer.  
Menu  
Description  
Change the transparency of the background of the OSD.  
Half Tone  
Menu Position  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
Play/Stop  
You can change the horizontal position where the OSD  
menu appears on your monitor.  
H-Position  
You can change the vertical position where the OSD menu  
appears on your monitor.  
V-Positon  
Menu  
Description  
The menu will be automatically turned if no adjustments are made for a  
certain time period.  
Menu Display Time  
You can set the amount of time the menu will wait before it is turned off.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu  
Description  
You can see the frequency, the polarity of the operational signals and the  
resolution level.  
Note: These screens do not allow any changes to the settings, they  
are for information only.  
Display Mode  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
Overview  
What is MagicTune™?  
Monitor performance can vary due to the graphics card, host computer lighting conditions and other  
environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique  
setting. Unfortunately, the manual controls available to tune the image often prove to be challenging. Proper  
adjustment (tuning) requires an easy to use program that goes through a step-by-step process to obtain the  
best overall picture quality.  
In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, on-  
screen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist in  
correctly setting the controls of the monitor. MagicTune is a software utility that guides you through the tuning  
process with easy to understand instructions and back ground patterns designed for each monitor control. The  
display settings for each user can be saved, providing an easy way to select display characteristics in a multi-  
user environment, or having a single user have multiple defined presets based on content and ambient lighting.  
Basic Functionality  
MagicTune is a software utility that allows monitor adjustment and color tuning using the Display Data  
Channel Command Interface (DDC/CI) protocol. All adjustments to the display are controlled via software  
to eliminate the need to use the monitor on-screen display (OSD).  
MagicTune supports Windows 98SE, Me, 2000, XP Home, and XP Professional.  
MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor  
configurations that are best suited for you.  
OSD Mode  
The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the  
desired menu item to set with ease.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
Installation  
1. Insert the installation CD into the CD-ROM drive.  
2. Click the MagicTune™ installation file.  
3. Select installation Language, Click "Next".  
4. When the InstallationShield Wizard window appears, click "Next."  
5. Select "I agree to the terms of the license agreement" to accept the terms of use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Choose a folder to install the MagicTune program.  
7. Click "Install."  
8. The "Installationation Status" window appears.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Click "Finish."  
10. When the installation is complete, the MagicTune executable icon appears on your desktop.  
Double-click the icon to start the program.  
Magictune execution icon may not appear depending on specification of computer  
system or monitor. If that happens, press F5 Key.  
Installationation Problems  
The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network  
environment.  
See "Troubleshooting" if you have trouble during installation.  
System Requirements  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OS  
z
z
z
z
z
Windows 98 SE  
Windows Me  
Windows 2000  
Windows XP Home Edition  
Windows XP Professional  
Hardware  
z
z
32MB Memory above  
25MB Hard disk space above  
* For more information, visit the MagicTune website.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
MagicTune allows for quick accurate tuning of the display with the ability to easily save  
and use monitor configurations that are best suited for you.  
z
z
OSD mode may appear inconsistent with the explanation in guidance  
book depending on specification of each monitor.  
When Pivot is functioning, part of Magictune Program may not  
operate normally.  
z
MagicTune control mode will be different according to monitor models.  
OSD Mode  
The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the  
control window displays the general descriptions of the sub-menu items for adjustment.  
When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD mode  
allows easy and convenient access to all tabs and sub-menu items.  
Button Tab Definition  
OK  
Applies any changes made and exits MagicTune.  
Restores the display settings to the factory settings.  
Reset  
Exits MagicTune without applying the changes made. If you have not made any changes  
in the control window, clicking "Cancel" does not cause any actions.  
Cancel  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Tab Definition  
Allows the user to adjust the screen settings to the desired values.  
Brightness  
Contrast  
Resolution  
MagicBright  
nmlkj  
nmlkji  
nmlkj  
nmlkj  
Makes the entire screen brighter or darker. The detailed data of the images in the dark  
areas can be lost if the brightness is not adjusted to the proper level. Adjust the  
brightness for best viewing conditions.  
Brightness  
Adjusts the difference in brightness between the bright and dark areas on screen.  
Determines the crispness of the images.  
Contrast  
Resolution  
Lists all display resolutions supported by the program.  
MagicBright™ is a new feature providing the optimum viewing environment depending on  
the contents of the image you are watching. Currently four different modes are available:  
Text, Internet, Entertain and Custom. Each mode has its own pre-configured brightness  
value. You can easily select one of four settings by simply pressing the MagicBright™  
control button.  
MagicBright™  
1. Text: For documentations or works involving heavy text.  
2. Internet: For working with a mixture of images such as text and graphics.  
3. Entertain: For watching motion pictures such as a DVD or VCD.  
4. Custom: Although the values are carefully chosen by our engineers, the pre-  
configured values may not be comfortable to your eyes depending on your taste. If  
this is the case, adjust the Brightness and Contrast by using the OSD menu.  
Color Tab Definition  
Adjusts the "warmth" of the monitor background or image color.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color Tone  
Color Control  
Calibration  
nmlkj  
nmlkji  
nmlkj  
The tone of the color can be changed.  
Color Tone  
z
z
Warm - Normal - Cool  
Custom  
Adjusts of the monitor image color.  
You can change the monitor color to your desired color.  
Color Control  
z
R- G - B  
The process through which the colors of your choice are optimized and maintained. You  
will find MagicTune extremely useful if you are one of those who wish to view images with  
their full details accurately reproduced - including web images and ones produced by a  
digital camera or scanner.  
Calibration  
Image Tab Definition  
Adjusts the Fine , Coarse and Position values.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Setup  
Position  
nmlkj  
nmlkji  
z
z
z
Fine : Removes noise such as horizontal stripes.  
If the noise persists even after Fine tuning, repeat it after adjusting the frequency  
(clock speed).  
Coarse : Removes noise such as vertical stripes.  
Coarse adjustment may move the screen image area.  
You may relocate it to the center using the Horizontal Control menu.  
Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming  
video signal. The values of fine, coarse and position are adjusted automatically.  
Image Setup  
Position  
Adjusts the screen location horizontally and vertically.  
Option Tab Definition  
You can configure MagicTune using the following options.  
Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To  
turn on or off any Preference, position the cursor over the box and click.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
z
z
Enable task tray menu .  
- To access the MagicTune menus, click the icon on the [task tray menu].  
The menus are not displayed if the [Enable System Tray] is deselected in  
[Options] ' [Basic Settings].  
Preferences  
Select Language - The language chosen affects only the language of the OSD.  
Source Select will be shown only in dual monitor.  
In analog only model source select will not be shown.  
Source Select  
z
z
Analog  
Digital  
Support Tab Definition  
Shows the Asset ID and the version number of the program, and allows you to use the Help feature.  
Visit the MagicTune website or click to open the Help files (User Manual) if you need any  
Help  
help installing or running MagicTune. The User Manual opens within a basic browser  
window.  
Asset ID  
User Name  
Shows the client monitor's user name.  
Shows the client monitor's ID.  
User ID  
Server IP  
Enter the IP Address of server PC.  
Enter the department of the client monitor.  
Enter the location of the client monitor.  
Department  
Location  
Version  
Displays the version of MagicTune.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
Color Calibration  
1. Color Calibration  
Color Calibration guides you to get optimal color condition for your monitor.  
Proceed following 5steps for getting optimal monitor color condition .  
1. Control "Brightness control bar" for matching the brightness of control patch and the brightness of background  
pattern  
2. When you detect specific color tone on "Control patch", move the control cursor toward to the direction of the  
color tone referring to "Color reference Circle".  
=> Adjustment is finished properly, you won't detect any color tone on Control patch.  
3. When you finish adjustment for step1,Click "Next" button .  
4. Repeat 1), 2), 3) procedures for remaining step2 ~ step5.  
5. You can easily view the calibration effect through clicking "Preview " button!  
How multiple users can use adjusted color values  
Definition  
When monitor is used by multiple users, color values which are adjusted via Color calibration for each users can be  
saved and used. Up to 5 users can use the saved color values.  
1. How to save adjusted color values:  
Press Next to make it change into Apply and then you can save adjusted color values.  
As many as 5 values can be saved.  
2. How to apply the saved color values:  
Press Multi User button on main screen to select and use one of the saved color values.  
2. Preview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Press "Preview" button on the Color Calibration.  
The above picture will be shown.  
1. Press "View Calibrated" button to see the calibration effect which you adjusted.  
2. Press "View Uncalibrated" button to see the original image.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
Uninstall  
The MagicTune program can be removed only by using the "Add or Remove Programs" option of the  
Windows Control Panel.  
Perform the following steps remove MagicTune.  
1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on  
Windows XP, go to [Control Panel] in the [Start] menu.  
2. Click the "Add or Remove Programs" icon in Control Panel.  
3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune." Click on it to highlight it.  
4. Click the "Change/Remove" button to remove the program.  
5. Click "Yes" to begin the uninstall process.  
6. Wait until the "Uninstall Complete" dialog box appears.  
Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and  
software upgrades.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color  
Calibration  
Overview  
|
Installation  
|
OSD Mode  
|
|
Uninstall  
|
Troubleshooting  
Troubleshooting  
z
MagicTune may not work in case monitor is replaced or driver of graphic card is updated while  
MagicTune is operating. If so, please restart the system.  
Symptom  
Check List  
Solutions  
Check when  
MagicTune does not  
function properly.  
MagicTune feature is found  
only on PC (VGA) with  
Window OS that supports  
Plug and Play.  
* To check whether your PC is available for  
MagicTune feature, follow the  
steps below (When Windows is XP);  
Control Panel -> Performance and Maintenance  
-> System -> Hardware -> Device Manager ->  
Monitors -> After deleting Plug and Play  
monitor, find 'Plug and Play monitor' by  
searching new Hardware.  
MagicTune is an additional software for the  
monitor. Some graphic cards may not support  
your monitor. When you have a problem with  
the graphic card, visit our website to check the  
compatible graphic card list provided.  
MagicTune™ doesn't Have you changed your PC  
work properly. or video graphic card?  
Download the latest program. The program can  
be downloaded  
z
z
Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.  
Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and  
software upgrades.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before calling for service, check the information in this section to see if you can remedy any  
problems yourself. If you do need assistance, please call the phone number on the  
Information section or contact your dealer.  
Symptom  
Check List  
Solutions  
No images on the  
screen. I cannot turn  
on the monitor.  
Is the power cord  
connected properly?  
Check the power cord connection  
and supply.  
Can you see  
"No  
Connection, Check  
Check the signal cable connection.  
on the  
Signal Cable"  
screen?  
If the power is on,  
If the initial screen (the login screen)  
reboot the computer to appears, boot the computer in the  
see the initial screen  
(the login screen),  
which can be seen.  
applicable mode (the safe mode for  
Windows ME/XP/2000) and then  
change the frequency of the video  
card.  
(Refer to the Preset Timing Modes)  
Note: If the initial screen (the login  
screen) does not appear, contact  
the Service Center or your dealer.  
Can you see  
mode not supported"  
on the screen?  
You can see this message when the  
signal from the video card exceeds  
the maximum resolution and  
frequency that the monitor can  
handle properly.  
"Video  
Adjust the maximum resolution and  
frequency that the monitor can  
handle properly.  
There is no image on  
the screen.  
Is the power indicator  
The monitor is in PowerSaver mode.  
press a key on the keyboard to  
on the monitor blinking activate the monitor and restore the  
at 1 second intervals?  
image on the screen.  
I cannot see the On  
Screen Display.  
Have you locked the  
On Screen Display  
(OSD) Menu to  
Unlock the OSD by pressing the  
MENU button for at least 5 seconds.  
prevent changes?  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The screen shows  
strange colors or just  
black and white.  
Is the screen  
Check the signal cable  
connection.Make sure the video  
card is fully inserted in it's slot.  
displaying only one  
color as if looking at  
the screen through a  
cellophane paper?  
Have the screen colors Reboot the computer.  
become strange after  
running a program or  
due to a crash  
between applications?  
Has the video card  
been set properly?  
Set the video card by referring to the  
video card manual.  
The screen suddenly  
has become  
unbalanced.  
Have you changed the Adjust screen image position and  
video card or the  
driver?  
size using the OSD.  
Have you adjusted the Adjust the resolution and frequency  
resolution or frequency of the video card.  
on the monitor?  
(Refer to the Preset Timing Modes).  
The screen can be unbalanced due to the cycle of the video card signals.  
Readjust Position by referring to the OSD.  
The screen is out of  
focus or OSD cannot  
be adjusted.  
Have you adjusted the Adjust the resolution and frequency  
resolution or frequency of the video card.  
on the monitor?  
(Refer to the Preset Timing Modes).  
LED is blinking but no  
images on the screen. properly adjusted  
when checking the  
Is the frequency  
Adjust the frequency properly by  
referring to the video card manual  
and the Preset Timing Modes.  
Display Timing on the  
menu?  
(The maximum frequency per  
resolution may differ from product to  
product.)  
There are only 16  
colors shown on the  
screen.  
Have the Windows  
colors been set  
properly?  
Windows ME/2000/XP:  
Set the colors properly at the  
Control Panel  
Display  
The screen colors  
have changed after  
changing the video  
card.  
.
Settings  
Has the video card  
been set properly?  
Set the video card by referring to the  
video card manual.  
There is a message  
that reads  
Have you installed the Install the monitor driver according  
monitor driver?  
to the Driver Installation Instructions.  
"Unrecognized  
monitor, Plug & Play  
(VESA DDC) monitor  
found".  
See the video card  
manual to see if the  
Plug & Play (VESA  
DDC) function can be  
supported.  
Install the monitor driver according  
to the Driver Installation Instructions.  
Check when  
MagicTune does not  
function properly.  
MagicTune feature is  
found only on PC  
(VGA) with Window  
OS that supports Plug  
and Play.  
* To check whether your PC is  
available for MagicTune feature,  
follow the  
steps below (When Windows is  
XP);  
Control Panel -> Performance and  
Maintenance -> System ->  
Hardware -> Device Manager ->  
Monitors -> After deleting Plug and  
Play monitor, find 'Plug and Play  
monitor' by searching new  
Hardware.  
MagicTune is an additional software  
for the monitor. Some graphic cards  
may not support your monitor. When  
you have a problem with the graphic  
card, visit our website to check the  
Download from Www.Somanuals.com. All Manuals Search And Download.  
compatible graphic card list  
provided.  
MagicTune™ doesn't  
work properly.  
Have you changed  
your PC or video  
graphic card?  
Download the latest program. The  
program can be downloaded  
Visit our website and download the installation software for MagicTune MAC.  
Check the following items if there is trouble with the monitor.  
1. Check if the power cord and the video cables are properly connected to the computer.  
2. Check if the computer beeps more than 3 times when booting.  
(If it does, request an after-service for the main board of the computer.)  
3. If you installed a new video card or if you assembled the PC, check if the installed the adapter  
(video) driver and the monitor driver.  
4. Check if the scanning ratio of the video screen is set at 56Hz ~ 75Hz.  
(Do not exceed 75Hz when using the maximum resolution.)  
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,  
remove the Display Adapter at the "  
" and then  
Control Panel System Device Administrator  
reboot the computer to reinstall the adapter (video) driver.  
If problems repeatedly occur, contact an authorized service center.  
Q & A  
Question  
Answer  
How can I change the  
frequency?  
Frequency can be changed by reconfiguring the video card.  
Note that video card support can vary, depending on the version  
of the driver used. (Refer to the computer or the video card  
manual for details.)  
How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control  
PanelDisplaySettings.  
* Contact the video card manufacturer for details.  
How can I set the Power Saving Windows XP : Set the resolution at the Control  
function?  
Panel¡æAppearance and Themes¡æDisplay¡æScreen Saver . Set  
the function at BIOS-SETUP of the computer. (Refer to  
Windows/Computer Manual).  
Windows ME/2000 : Set the resolution at the Control  
Panel¡æDisplay¡æScreen Saver. Set the function at BIOS-SETUP  
of the computer. (Refer to Windows/Computer Manual).  
How can I clean the outer  
case/LCD Panel?  
Disconnect the power cord and then clean the monitor with a soft  
cloth, using either a cleaning solution or plain water.  
Do not leave any remains of the detergent nor scratch the case.  
Do not allow any water to go inside the monitor.  
Self-Test Feature Check  
Self-Test Feature Check | Warning Messages | Environment | Useful Tips  
Your monitor provides a self test feature that allows you to check whether your monitor is  
Download from Www.Somanuals.com. All Manuals Search And Download.  
functioning properly.  
Self-Test Feature Check  
1. Turn off both your computer and the monitor.  
2. Unplug the video cable from the back of the computer.  
3. Turn on the monitor.  
If the monitor is functioning properly, you will see a box in the illustration below.  
This box appears during normal operation if the video cable becomes disconnected or  
damaged.  
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the  
monitor.  
If your monitor screen remains blank after using the previous procedure, check your video  
controller and computer system; your monitor is functioning properly.  
Warning Messages  
If there is something wrong with the input signal, the message below appears on the screen  
or the screen goes blank although the power indicator LED is still on. The message may  
indicate that the monitor is out of scan range or that you need to check the signal cable.  
Environment  
The location and the position of the monitor may influence the quality and other  
features of the monitor.  
1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer  
to another room.  
2. Remove all electronic devices such as radios, fans, clocks and telephones that are  
within 3 feet (one meter) of the monitor.  
Useful Tips  
z
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with  
the computer or the video card, this can cause the monitor to become blank, have poor coloring,  
noise, unavailable video mode, etc. In this case, first check the source of the problem, and then  
contact the Service Center or your dealer.  
z
Judging the monitor's working condition  
If there is no image on the screen or a  
message comes up,  
"Video mode not supported"  
disconnect the cable from the computer while the monitor is still powered on.  
{
{
If there is a message coming up on the screen or if the screen goes white, this means the  
monitor is in working condition.  
In this case, check the computer for trouble.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
General  
General  
Model Name  
LCD Panel  
SyncMaster 151x  
Size  
15" Diagonal  
Display area  
Pixel Pitch  
304.1mm (H) x 228.1mm (V)  
0.297mm (H) x 0.297mm (V)  
a-si TFT active matrix  
Type  
Synchronization  
Horizontal  
31 ~ 60 kHz  
56 ~ 75 Hz  
Vertical  
Display Color  
16,194,277 Colors  
Resolution  
Optimum resolution  
Maximum resolution  
Input Signal, Terminated  
1024 x 768@60 Hz  
1024 x 768@75 Hz  
RGB Analog  
0.7Vp-p Positive at 75 ohms  
Separate H/V sync, SOG(Option), TTL level positive or negative.  
Maximum Pixel Clock  
80 MHz  
Power Supply  
AC 100 ~ 240VAC(+/- 10%), 60/50 Hz ± 3Hz  
Signal Cable  
15pin-to-15pin D-sub cable, detachable  
Power Consumption  
Less than 30W  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions (WxDxH)/ Weight  
326.3 x 49.5 x 267.1 mm / 12.8 x 1.9 x 10.5 inch (Without Stand)  
326.3 x 158.7 x 314.3 mm / 12,8 x 6,2 x 12,4 inch (with Basic Stand) / 2.5kg  
VESA Mounting Interface  
75mm x 75mm (for use with Specialty(Arm) Mounting hardware.)  
Environmental considerations  
Operating  
Temperature: 50°F ~ 104°F(10°C ~ 40°C)  
Humidity: 10% ~ 80%, non-condensing  
Storage  
Temperature: -4°F ~113°F (-20°C ~ 45°C)  
Humidity: 5% ~ 95%, non-condensing  
Plug and Play Capability  
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and  
computer systems will provide the best operating conditions and monitor settings. In most cases,  
monitor installation will proceed automatically, unless the user wishes to select alternate settings.  
Note: Design and specifications are subject to change without prior notice.  
PowerSaver  
This monitor has a built-in power management system called PowerSaver. This system saves energy  
by switching your monitor into a low-power mode when it has not been used for a certain amount of  
time. The monitor automatically returns to normal operation when you press a key on the keyboard. For  
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for  
long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in  
your computer. Use a software utility installed on your computer to set up this feature.  
Power saving mode  
State  
Normal Operation  
Power Switch off  
EPA/ENERGY 2000  
Green, Blinking  
Less than 2W  
Power Indicator  
Green  
Black  
Power Consumption  
Less than 30W  
Less than 1W  
®
This monitor is EPA ENERGY STAR compliant and ENERGY2000  
compliant when used with a computer equipped with VESA DPMS  
functionality.  
®
As an ENERGY STAR Partner, SAMSUNG has determined that this  
®
product meets the ENERGY STAR guidelines for energy efficiency.  
Preset Timing Modes  
If the signal transferred from the computer is the same as the following Preset Timing Modes, the  
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while  
the power LED is on. Refer to the video card manual and adjust the screen as follows.  
Table 1. Preset Timing Modes  
Horizontal  
Frequency  
(kHz)  
Vertical  
Frequency  
(Hz)  
Pixel Clock  
(MHz)  
Sync Polarity  
(H/V)  
Display Mode  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IBM, 640 x 350  
IBM, 640 x 480  
31.469  
31.469  
31.469  
35.000  
49.726  
37.500  
37.861  
35.156  
37.879  
46.875  
48.077  
48.363  
56.476  
60.023  
70.086  
59.940  
70.087  
66.667  
74.551  
75.000  
72.809  
56.250  
60.317  
75.000  
72.188  
60.004  
70.069  
75.029  
25.175  
25.175  
28.322  
30.240  
57.284  
31.500  
31.500  
36.000  
40.000  
49.500  
50.000  
65.000  
75.000  
78.750  
+/-  
-/-  
IBM, 720 x 400  
-/+  
-/-  
MAC, 640 x 480  
MAC, 832 x 624  
VESA, 640 x 480  
VESA, 640 x 480  
VESA, 800 x 600  
VESA, 800 x 600  
VESA, 800 x 600  
VESA, 800 x 600  
VESA, 1024 x 768  
VESA, 1024 x 768  
VESA, 1024 x 768  
-/-  
-/-  
-/-  
-/-  
+/+  
+/+  
+/+  
-/-  
-/-  
+/+  
Horizontal Frequency  
The time to scan one line connecting the right edge to the left edge of  
the screen horizontally is called Horizontal Cycle and the inverse  
number of the Horizontal Cycle is called Horizontal Frequency. Unit:  
kHz  
Vertical Frequency  
Like a fluorescent lamp, the screen has to repeat the same image  
many times per second to display an image to the user. The  
frequency of this repetition is called Vertical Frequency or Refresh  
Rate. Unit: Hz  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
The address and phone number of the company can be changed without prior notice.  
AUSTRALIA :  
Samsung Electronics Australia Pty Ltd.  
Customer Response Centre  
7 Parkview Drive, Homebush Bay NSW 2127  
Tel : 1300 362 603  
BRAZIL :  
Samsung Eletronica da Amazonia Ltda.  
R. Prof. Manoelito de Ornellas, 303, Terro B  
Chacara Sto. Antonio, CEP : 04719-040  
Sao Paulo, SP  
SAC : 0800 124 421  
CANADA :  
Samsung Electronics Canada Inc.  
Samsung Customer Care  
7037 Financial Drive  
Mississauga, Ontario  
L5N 6R3  
1-800-SAMSUNG (1-800-726-7864)  
CHILE :  
SONDA S.A.  
Teatinos 550, Santiago Centro, Santiago, Chile  
Fono: 56-2-5605000 Fax: 56-2-5605353  
56-2-800200211  
COLOMBIA :  
Samsung Electronics Colombia  
Cra 9 No 99A-02 Of. 106  
Bogota, Colombia  
Tel.: 9-800-112-112  
Fax: (571) 618 - 2068  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESPAÑA :  
Samsung Electronics Comercial Iberica, S.A.  
Ciencies, 55-65 (Poligono Pedrosa) 08908  
Hospitalet de Llobregat (Barcelona)  
Tel. : (93) 261 67 00  
Fax. : (93) 261 67 50  
FRANCE :  
SAMSUNG ELECTRONICS FRANCE Service  
Paris Nord 2  
66 rue des Vanesses  
BP 50116 Villepinte  
95950 Roissy CDG Cedex  
Tel : 08 25 08 65 65  
Fax : 01 48 63 06 38  
GERMANY :  
TELEPLAN Rhein-Main GmbH  
Feldstr. 16  
64331 Weiterstadt  
T. 06151/957-1306  
F. 06151/957-1732  
* EURO 0.12/Min  
HUNGARY :  
Samsung Electronics Magyar Rt.  
1039, Budapest, Lehel u. 15-17.  
Tel: 36 1 453 1100  
Fax: 36 1 453 1101  
ITALY :  
Samsung Electronics Italia S.p.a.  
Via C. Donat Cattin, 5  
20063 Cernusco s/Naviglio (MI)  
Servizio Clienti: 199.153.153  
MÉXICO :  
SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.  
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan  
Tultitlán, Estado de México, C.P. 54940  
Tel: 01-55-5747-5100 / 01-800-726-7864  
Fax: 01-55-5747-5202 / 01-800-849-1743  
RFC: SEM950215S98  
IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.  
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan  
Tultitlán, Estado de México, C.P. 54940  
Tel: 01-55-5747-5100 / 01-800-726-7864  
EXPORTADO POR: Samsung Electronics CO.,LTD.  
416, Mae tan-3dong, Yeongtong - gu,  
Suwon City, Gyeonggi-do Korea  
NETHERLANDS/BELGIUM/LUXEMBOURG :  
Samsung Electronics Benelux B. V.  
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS  
Service and informatielijn ;  
Belgium :0800-95214, http://www.samsung.be/  
Netherlands : 0800-2295214, http://www.samsung.nl/  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PANAMA :  
Samsung Electronics Latinoamerica( Z.L.) S.A.  
Calle 50 Edificio Plaza Credicorp, Planta Baja  
Panama  
Tel. : (507) 210-1122, 210-1133  
Tel : 800-3278(FAST)  
PERU :  
Servicio Integral Samsung  
Av.Argentina 1790 Lima1. Peru  
Tel: 51-1-336-8686  
Fax: 51-1-336-8551  
PORTUGAL :  
SAMSUNG ELECTRONICA PORTUGUESA S.A.  
o
Rua Mário Dioniso, N 2 - 1º Drt. 2795-140 LINDA-A-VELHA  
Tel. 214 148 114/100 Fax. 214 148 133/128  
Free Line 800 220 120  
SOUTH AFRICA :  
Samsung Electronics,5 Libertas Road, Somerset Office Park,  
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa  
Tel : 0027-11-549-1621  
Fax : 0027-11-549-1629  
SWEDEN/DENMARK/NORWAY/FINLAND :  
Samsung Electronics AB  
Box 713  
S-194 27 UPPLANDS VÄSBY  
SVERIGE  
Besöksadress : Johanneslundsvägen 4  
Samsung support Sverige: 020-46 46 46  
Samsung support Danmark : 8088-4646  
Samsung support Norge: 8001-1800  
Samsung support Finland: 0800-118001  
Tel +46 8 590 966 00  
Fax +46 8 590 966 50  
THAILAND :  
HAI SAMSUNG SERVICE CENTER  
MPA COMPLEX BUILDING,1st-2nd Floor  
175 SOI SUEKSA VIDHAYA SATHON SOI 12  
SILOM ROAD ,SILOM,BANGRAK  
BANGKOK 10500  
TEL : 0-2635-2567  
FAX : 0-2635-2556  
UKRAINE :  
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE  
4 Glybochitska str.  
Kiev, Ukraine  
Tel. 8-044-4906878  
Fax 8-044-4906887  
Toll-free 8-800-502-0000  
United Kingdom :  
Samsung Electronics (UK) Ltd.  
Samsung House, 225 Hook Rise South  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Surbiton, Surrey KT6 7LD  
Tel. : (0208) 391 0168  
Fax. : (0208) 397 9949  
< European Service Center & National Service >  
Stafford Park 12 Telford, Shropshire, TF3 3BJ  
Tel. : (0870) 242 0303  
Fax. : (01952) 292 033  
U.S.A :  
Samsung Electronics America  
Service Division  
400 Valley Road, Suite 201  
Mount Arlington, NJ 07856  
1-800-SAMSUNG (1-800-726-7864)  
Terms  
Dot Pitch  
The image on a monitor is composed of red, green and blue dots. The closer the dots, the  
higher the resolution. The distance between two dots of the same color is called the 'Dot  
Pitch'. Unit: mm  
Vertical Frequency  
The screen must be redrawn several times per second in order to create and display an image  
for the user. The frequency of this repetition per second is called Vertical Frequency or  
Refresh Rate. Unit: Hz  
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.  
Horizontal Frequency  
The time to scan one line connecting the right edge to the left edge of the screen horizontally  
is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal  
Frequency. Unit: kHz  
Interlace and Non-Interlace Methods  
Showing the horizontal lines of the screen from the top to the bottom in order is called the  
Non-Interlace method while showing odd lines and then even lines in turn is called the  
Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a  
clear image. The Interlace method is the same as that used in TVs.  
Plug & Play  
This is a function that provides the best quality screen for the user by allowing the computer  
and the monitor to exchange information automatically. This monitor follows the international  
standard VESA DDC for the Plug & Play function.  
Resolution  
The number of horizontal and vertical dots used to compose the screen image is called  
'resolution'. This number shows the accuracy of the display. High resolution is good for  
performing multiple tasks as more image information can be shown on the screen.  
Example: If the resolution is 1024 x 768 , this means the screen is composed of 1024  
horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).  
For Better Display  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described  
below to enjoy the best quality of picture. You can have an uneven quality of picture in the  
screen if the best quality of picture is not provided in TFT-LCD.  
{
{
Resolution: 1024 x 768  
Vertical frequency (refresh rate): 60 Hz  
2. When you clean the monitor and the panel outside, please apply the recommended small  
amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but  
to be scrubbed out softly.  
If excessive force is applied, you can have a stain on it.  
3. If you are not satisfied with the quality of picture, you can get better quality of picture by  
executing "auto adjustment function" in display screen that is appeared as window  
termination button is pressed.  
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.  
4. If you view a fixed screen for an extended period of time, residual image or blurriness may  
appear.  
Change the mode to energy save or set a screensaver to moving picture when you need to  
be away from the monitor for an extended period of time.  
Authority  
Information in this document is subject to change without notice.  
© 2005 Samsung Electronics Co., Ltd. All rights reserved.  
Reproduction in any manner whatsoever without the written permission of Samsung Electronics  
Co., Ltd. is strictly forbidden.  
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or  
consequential damages in connection with the furnishing, performance, or use of this material.  
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and  
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are  
registered trademarks of Video Electronics Standard Association; the ENERGY STAR® name and  
logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an  
ENERGY STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets  
the ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein  
may be the trademarks or registered trademarks of their respective owners.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Information | IC Compliance Notice | MPR II Compliance  
European Notice (Europe only) | PCT Notice | VCCI |  
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)  
TCO'99-Ecological requirements for personal computers (TCO'99 applied model only)  
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)  
TCO'03 Recycling Information (TCO'03 applied model only)  
Medical Requirement  
Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only)  
FCC Information  
User Instructions  
The Federal Communications Commission Radio Frequency Interference Statement includes  
the following warning:  
This equipment has been tested and found to comply with the limits for a Class B digital  
Note:  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television receptions, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
z
z
z
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
z
User Information  
Changes or modifications not expressly approved by the party responsible for compliance could  
void the user's authority to operate the equipment. If necessary, consult your dealer or an  
experienced radio/television technician for additional suggestions. You may find the booklet  
called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was  
prepared by the Federal Communications Commission. It is available from the U.S.  
Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4.  
The party responsible for product compliance:  
SAMSUNG ELECTRONICS CO., LTD  
America QA Lab of Samsung  
3351 Michelson Drive,  
Suite #290, Irvine, CA92612 USA  
Tel) 949-975-7310  
Fax) 949-922-8301  
Warning  
User must use shielded signal interface cables to maintain FCC compliance for the product.  
Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It  
may be suitable for connection to any UL Listed personal computer with similar configuration.  
Before making the connection, make sure the voltage rating of the computer convenience outlet  
is the same as the monitor and that the ampere rating of the computer convenience outlet is  
equal to or exceeds the monitor voltage rating.  
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration  
5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable  
power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.  
IC Compliance Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations of ICES-003.  
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur  
les équipements produisant des interférences au Canada.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPR II Compliance  
This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and  
magnetic fields.  
European Notice(Europe Only)  
Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC),  
(93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the  
European Community. Compliance with these directives implies conformity to the following  
European Norms:  
z
z
z
z
EN55022:1998+A1:2000 - Radio Frequency Interference  
EN55024:1998 - Electromagnetic Immunity  
EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics  
EN61000-3-3:1995 - Voltage Fluctuations  
PCT Notice  
VCCI  
This is a Class B product based on the standard of the Voluntary Control Council for  
Interference by Information Technology Equipment (VCCI). If this is used near a radio or  
television receiver in a domestic environment, it may cause radio interference. Install and use  
the equipment according to the instruction manual.  
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)  
AB general requirements  
AB2 Written Eco-document acompanying the products  
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your  
choice has provided you with a product developed for professional use. Your purchase has also  
contributed to reducing the burden on the environment and to the further development of  
environmentally-adapted electronic products.  
Why do we have environmentally-labelled monitors?  
In many countries, environmental labelling has become an established method for encouraging  
the adaptation of goods and services to the environment.The main problem as far as monitors  
and other electronic equipment are concerned is that environmentally harmful substances are  
used both in the products and during their manufacture. Since it has not been possible so far  
for the majority of electronic equipment to be recycled in a satisfactory way, most of these  
potentially damaging substances sooner or later enter Nature.  
There are also other characteristics of a monitor, such as energy consumption levels, that are  
important from both the working and natural environment viewpoints. Since all types of  
conventional electricity generation have a negative effect on the environment (acidic and  
Download from Www.Somanuals.com. All Manuals Search And Download.  
climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic  
equipment in offices consumes an enormous amount of energy, since it is often routinely left  
running continuously.  
What does labelling involve?  
This product meets the requirements for the TCO'95 scheme, which provides for international  
environmental labelling of monitors. The labelling scheme was developed as a joint effort by the  
TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The  
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and  
Technical Development in Sweden).  
The requirements cover a wide range of issues: environment, ergonomics, usability, emission  
of electrical and magnetic fields, energy consumption and electrical and fire safety.  
The environmental demands concern among other things restrictions on the presence and use  
of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated  
solvents. The product must be prepared for recycling and the manufacturer is obliged to have  
an environmental plan, which must be adhered to in each country where the company conducts  
its operations policy. The energy requirements include a demand that the monitor after a certain  
period of inactivity shall reduce its power consumption to a lower level, in one or more stages.  
The length of time to reactivate the monitor shall be reasonable for the user.  
Labelled products must meet strict environmental demands, for example in respect of the  
reduction of electric and magnetic fields, along with physical and visual ergonomics and good  
usability.  
TCO Development Unit 1996-11-29  
On the page this folder you will find a brief summary of the environmental requirements met by  
this product.  
The complere environmental criteria document may be ordered from:  
TCO Development Unit  
S-11494 Stockholm  
Sweden  
Fax: +46 8 782 92 07  
E-mail (Internet): [email protected]  
Current information regarding TCO'95-approved and labelled products may also  
be obtained via the Internet, using the address:  
TCO'95 is a co-operative project between(3 logos)  
Environmental Requirements  
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and  
housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer  
casing can consist of flame retardant substances. These are related to another group of  
environmental toxins, PCBs, which are suspected to give rise to similar harm, including  
reproductive damage in fish eating birds and mammals, due to the bioaccumulative processes.  
Flame retardants have been found in human blood and researchers fear that disturbances in  
foetus development may occur.  
z
TCO'95 demand requires that plastic components weighing more than 25 grams must not  
contain organically bound chlorine and bromine.  
Lead  
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the  
nervous system and in higher doses, causes lead poisoning.  
z
TCO'95 requirement Permits the inclusion of lead since no replacement has yet been  
developed.  
Cadmium  
Cadmium is present in rechargeable batteries and in the colour generating layers of certain  
computer displays. Cadmium damages the nervous system and is toxic in high doses.  
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per  
million) of cadmium. The colour-generating layers of display screens must not contain any  
cadmium.  
Mercury  
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous  
system and is toxic in high doses.  
z
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per  
million) of mercury. It also demands that no mercury is present in any of the electrical or  
electronics components concerned with the display unit.  
CFCs (freons)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing  
of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone  
layer in the stratosphere, causing increased reception on Earth of ultraviolet light with  
consequent increased risks of skin cancer (malignant melanoma).  
z
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during the  
manufacturing of the product or its packaging.  
TCO'99-Ecological requirements for personal computers (TCO'99 applied model only)  
Congratulations!  
You have just purchased a TCO'99 approved and labelled product! Your choice has provided  
you with a product developed for professional use. Your purchase has also contributed to  
reducing the burden on the environment and also to the further development of environmentally  
adapted electronics products.  
This product meets the requirements for the TCO'99 scheme which provides for an  
international environmental and quality labelling labelling of personal computers. The labelling  
scheme was developed as a joint effort by the TCO(The Swedish Confederation of Professional  
Employees), Svenska Naturskyddsforeningen(The Swedish Society for Nature Conservation),  
Statens Energimyndighet(The Swedish National Energy Administration) and SEMKO AB.  
The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction  
of electric and magnetic fields, energy consumption and electrical safety.  
Why do we have environmentally labelled computers?  
In many countries, environmental labelling has become an established method for encouraging  
the adaptation of goods and services to the environment. The main problem, as far as  
computers and other electronics equipment are concerned, is that environmentally harmful  
substances are used both in the products and during their manufacture. Since it is not so far  
possible to satisfactorily recycle the majority of electronics equipment, most of these potentially  
damaging substances sooner or later enter nature.  
There are also other characteristics of a computer, such as energy consumption levels, that are  
important from the viewpoints of both the work (internal) and natural (external) environments.  
Since all methods of electricity generation have a negative effect on the environment (e.g.  
acidic and climate-influencing emissions, radioactive waste), it is vital to save energy.  
Electronics equipment in offices is often left running continuously and thereby consumes a lot of  
energy.  
What does labelling involve?  
The environmental demands has been developed by Svenska Naturskyddsforeningen (The  
Swedish Society for Nature Conservation). These demands impose restrictions on the  
presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs(freons)  
and chlorinated solvents, among other things. The product must be prepared for recycling and  
the manufacturer is obliged to have an environmental policy which must be adhered to in each  
country where the company implements its operational policy.  
The energy requirements include a demand that the computer and/or display, after a certain  
period of inactivity, shall reduce its power consumption to a lower level in one or more stages.  
The length of time to reactivate the computer shall be reasonable for the user.  
Below you will find a brief summary of the environmental requirements met by this product. The  
complete environmental criteria document may be ordered from:  
TCO Development  
SE-114 94 Stockholm, Sweden  
Fax: +46 8 782 92 07  
Email (Internet): [email protected]  
Current information regarding TCO'99 approved and labelled products may also be obtained  
via the Internet, using the address: http://www.tco-info.com/  
Environmental requirements  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Flame retardants  
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.  
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a  
computer casing can consist of flame retardant substances. Most flame retardants contain  
bromine or chloride, and those flame retardants are chemically related to another group of  
environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the  
PCBs are suspected of giving rise to severe health effects, including reproductive damage in  
fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have  
been found in human blood and researchers fear that disturbances in foetus development may  
occur.  
The relevant TCO'99 demand requires that plastic components weighing more than 25 grams  
must not contain flame retardants with organically bound bromine or chlorine. Flame retardants  
are allowed in the printed circuit boards since no substitutes are available.  
Cadmium**  
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain  
computer displays. Cadmium damages the nervous system and is toxic in high doses. The  
relevant TCO'99 requirement states that batteries, the colour-generating layers of display  
screens and the electrical or electronics components must not contain any cadmium.  
Mercury**  
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system  
and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not  
contain any mercury. It also demands that mercury is not present in any of the electrical or  
electronics components associated with the labelled unit. There is however one exception.  
Mercury is, for the time being, permitted in the back light system of flat panel monitors as today  
there is no commercially available alternative. TCO aims on removing this exception when a  
Mercury free alternative is available.  
CFCs (freons)  
The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the  
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing  
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the  
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks  
of skin cancer (malignant melanoma) as a consequence.  
Lead**  
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the  
nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement  
permits the inclusion of lead since no replacement has yet been developed.  
TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)  
Congratulations!  
The display you have just purchased carries the TCO'03 Displays label. This means that your  
display is designed, manufactured and tested according to some of the strictest quality and  
environmental requirements in the world. This makes for a high performance product, designed  
with the user in focus that also minimizes the impact on our natural environment.  
Some of the features of the TCO'03 Display requirements:  
Ergonomics  
Good visual ergonomics and image quality in order to improve the working environment for the  
user and to reduce sight and strain problems. Important parameters are luminance, contrast,  
resolution, reflectance, colour rendition and image stability.  
Energy  
z
Energy-saving mode after a certain time ?beneficial both for the user and the environment  
Electrical safety  
z
Download from Www.Somanuals.com. All Manuals Search And Download.  
Emissions  
z
z
Electromagnetic fields  
Noise emissions  
Ecology  
z
The product must be prepared for recycling and the manufacturer must have a certified  
environmental management system such as EMAS or ISO 14 000  
z
Restrictions on  
o chlorinated and brominated flame retardants and polymers  
o heavy metals such as cadmium, mercury and lead.  
The requirements included in this label have been developed by TCO Development in  
cooperation with scientists, experts, users as well as manufacturers all over the world. Since  
the end of the 1980s TCO has been involved in influencing the development of IT equipment in  
a more user-friendly direction. Our labelling system started with displays in 1992 and is now  
requested by users and IT-manufacturers all over the world.  
For more information, Please visit  
TCO'03 Recycling Information (TCO'03 applied model only)  
For recycling information for TCO'03 certified monitors, for the residents in the following  
countries, please contact the company corresponding to your region of residence. For those  
who reside in other countries, please contact a nearest local Samsung dealer for recycling  
information for the products to be treated in environmentally acceptable way.  
[U.S.A. Residents Only]  
U.S.A.  
[European Residents Only]  
NORWAY  
SWEDEN  
GERMANY  
vfw AG  
Solid Waste Transfer &  
Recycling Inc  
COMPANY  
ADDRESS  
ELKRETSEN  
Elektronikkretur AS  
ELKRETSEN Box  
1357, 111 83  
Stockholm  
Barnhusgatan 3, 4  
tr.  
Max Plank Strasse  
6454 Etterstad 0602 Oslo 42  
442 Frelinghuysen Ave  
Newark, NJ 07114  
Fyrstikkalln 3B  
50858 Collogne  
Germany  
TELEPHONE 973-565-0181  
08-545 212 90  
08-545 212 99  
23 06 07 40  
23 06 07 41  
49 0 2234 9587 - 0  
FAX  
Fax: 973-565-9485  
none  
E-  
MAIL  
HOME  
PAGE  
Waste_Disposal.htm kretsen.se/  
Medical Requirement  
Classifications:  
In accordance with UL 2601-1/IEC 60601-1, the product is cssified as Continuous duty Class I  
equipment, which is not protected against ingress of liquids. The product is not suitable for use  
in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide.  
EMC  
This equipment has been tested and found to comply with the limits for medical devices to the  
IEC 601-1-2:1994. These limits are designed to provide reasonable protection against harmful  
interference in a typical medical installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in accordance with the instructions, may  
Download from Www.Somanuals.com. All Manuals Search And Download.  
cause harmful interference to other devices in the vicinity. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to other devices, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following measures:  
z
z
z
Reorient or relocate the receiving device.  
Increase the separation between the equipment.  
Connect the equipment into an outlet on a circuit different from that to which the other  
device(s) are connected.  
z
Consult the manufacturer or field service technician for help.  
Video In / RS 232 / Video Out  
Accessories equipment connected to the analog and digital interfaces must be certified to the  
respective IEC standards (i.e. IEC 950 for data processing equipment and IEC 601-1 for  
medical equipment.) Furthermore all configurations shall comply with the system standard IEC  
601-1-1. Everybody who connects additional equipment to the signal input part or signal output  
part configures a medical system, and is therefore, responsible that the system complies with  
the requirements of the system standard IEC 601-1-1. If in doubt, consult the technical services  
department or your local representative.  
Transport and Storage Limitations:  
Temperature Range of -40°C to +70°C  
Relative Humidity of 10 -95%, non-condensing  
* Bio-accumulative is defined as substances which accumulate within living organisms.  
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.  
Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only)  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR  
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS  
For details see lamprecycle.org, eiae.org, or call 1-800-Samsung  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT INFORMATION (Image Retention Free)  
LCD Monitors and TVs may have image retention when switching from one image to another  
especially after displaying a stationary image for a long time.  
This guide is to demonstrate correct usage of LCD products in order to protect them from Image  
retention.  
What is Image retention ?  
During normal operation of a LCD panel, pixel image retention doesn't occur. However,  
if the same image is displayed for a long time, a slight difference in electric charge  
accumulates between the two electrodes which encase the liquid crystal. This may  
cause the liquid crystal to build up in a certain areas of the display. Thus, the previous  
image is retained when switching to a new video image. All display products, including  
LCD,are subject to image retention. This is not a product defect.  
Please follow the suggestions below to protect your LCD from image retention  
Power Off, Screen Saver, or Power Save Mode  
Ex)  
z
Turn the power off when using a stationary pattern.  
- Turn the power off for 4 hours after 24 hours in use  
- Turn the power off for 2 hours after 12 hours in use  
Use a Screen saver if possible  
- Screen saver in one color or a moving image is recommended.  
Set the Monitor to power off with the PC Display Properties Power Scheme.  
z
z
Suggestions for specific applications  
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems  
We recommend that you follow set up of your display system program as below:  
Display Information together with Logo or Moving image cycle.  
Ex) Cycle : Display Information for 1 hour followed by a  
Display Logo or moving image for 1 minute.  
Change the Color Information periodically (Use 2 different colors).  
Ex) Rotate the Color Information with 2 colors every 30 minutes.  
Avoid using a combination of characters and background color with large  
difference in luminance.  
Avoid using Grey colors, which can cause Image retention easily.  
z
Avoid: Colors with big difference in luminance (Black & White, Grey)  
Ex)  
z
Recommended settings: Bright colors with little difference in luminance  
- Change the characters color and background color every 30 minutes  
Ex)  
- Every 30 minutes, change the characters with movement.  
Ex)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The best way to protect your monitor from Image retention is to set your PC or  
System to operate a Screen Saver program when you are not using it.  
Image retention may not occur when a LCD panel is operated under normal conditions.  
Normal conditions are defined as continuously changing video patterns. When the LCD  
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be  
slight difference in voltage between electrodes that work the liquid crystal (LC) in a  
pixel. The voltage difference between electrodes increases with time, forcing the liquid  
crystal to lean. When this occurs, the previous image may be seen when the pattern is  
changed.  
To prevent this, the accumulated voltage difference must be decreased.  
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Correct Disposal of This Product  
(Waste Electrical & Electronic Equipment) - Europe only  
(Applicable in the European Union and other European countries with  
separate collection systems)  
This marking shown on the product or its literature, indicates that it should not  
be disposed with other household wastes at the end of its working life. To  
prevent possible harm to the environment or human health from uncontrolled  
waste disposal, please separate this from other types of wastes and recycle it  
responsibly to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased this  
product, or their local government office, for details of where and how they  
can take this item for environmentally safe recycling.  
Business users should contact their supplier and check the terms and  
conditions of the purchase contract. This product should not be mixed with  
other commercial wastes for disposal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Surge Protector 61 189 User Guide
RCA Handheld TV F27718, F32718, F36718, MR68R718 User Guide
Renesas Computer Hardware M30263T 42SSB User Guide
Russound Speaker SUB85 User Guide
Salton Juicer JM1 User Guide
Salton Slow Cooker FSSC500 User Guide
Samsung MP3 Player YH 820 User Guide
Schumacher Battery Charger XC103 User Guide
Sears Snow Blower 486248463 User Guide
Sears Treadmill NTL190100 User Guide