ENFORCER PASSIVE PCI VIDEO BALUN HUB
Installation Manual
Specifications:
EVT-PC4-VT2Q (Video Balun Card)
Range*
®
EVT-PC4P-JTQ (Power Card)
B/W: 2,000 feet (610M)
Video Input
Power Input
Power Output
Power Indicator
Voltage output
Removable terminal block
Power jack (2.1mm jack)
Removable terminal block
3-color LED
ENFORCER
Color: 1,300 feet (400M)
RS170, NTSC, PAL, SECAM, CCIR
1vpp
<2dB per pair from DC ~ 5 Mhz
>-15dB from DC ~ 5 Mhz
DC ~ 5 Mhz
Video Format
Maximum Input
Insertion Loss
Return Loss
Frequency Response
Attenuation
Common Mode Rejection 60 dB, 15 KHz~5 MHz
Impedance
Coax, Male BNC
Terminal Block
Power
Temperature Range
Humidity Range
Wire Type
Wire Category
UTP Connection
No. of channel
12VDC (inc. power adapter)
EVT-PC4-VT2Q
EVT-PC4-VT2Q
Total Supply Current 4 Amp. (inc. power adaptor)
o
o
o
o
4-port PCI Passive Video Balun Hub
Range: Up to 2,000’ (610mm)
Temperature Range 14 ~165 F (-10 ~74 C)
Humidity Range
Wire Type
Wire Category
0 ~ 95%
UTP ( 16 - 24 AWG)
CAT2 or better, CAT5 ideal
DC ~ 5 Mhz, 1.5 dB max
EVT-PC4P-JTQ
4-port PCI Power Distributor Card
Range: See chart on page 4.
75 Ohms @ 1 MHz
100 Ohms @ 1 MHz
No power required
EVT-PC4P-JTQ
EVT-PC4KQ
o
o
o
o
14 ~165 F (-10 ~74 C)
0 ~ 95%
4-port PCI Video Balun Hub & Power Card Set
(Includes 4 Amp 12VDC Adapter)
UTP ( 16 - 24 AWG)
CAT2 or better, CAT5 ideal
Screwless Terminal Blocks
4
WHAT IT IS
*Note: Shorter range may result when baluns are used with DVR.
The ENFORCER EVT-PC4-VT2Q is a 4-port PCI Video Balun Hub specifically designed for PC based DVR cards . The
EVT-PC4-VT2Q is the most practical and cost efficient way of connecting video signals from CCTV cameras to PC
based DVR cards via Cat5 cables. It eliminates the need to install individual video baluns on the DVR card side, and is
equipped with a gold plated BNC connector for optimum video performance and a screwless terminal block for
convenient and organized wiring installations.
The EVT-PC4P-JTQ is an add-on power card for EVT-PC4-VT2Q. When installed with EVT-PC4-VT2Q it will allow power
to be transmitted from the PC side to CCTV camera side over the same UTP cables used by the video signal. It
centralizes the power suppy of CCTV cameras.
*
Minimum Distance Over UTP @ 12VDC
Current Draw 1 Pair 2 Pair 3 Pair
100mA
300mA
1 Amp
100’
30’
N/A
200’
60’
15’
300’
100’
30’
Installation
Installing the EVT-PC4-VT2Q and EVT-PC4P-JTQ
Note: Maximum distance depends on voltage, current, ambient temperature, and wire guage.
*
1. Shut down the computer, disconnect the power and remove the computer cover from its chasis. See Fig. 2.
(Maximize distance with 3 UTP pairs.)
2. Determine the location of the available card slots at the back panel of the computer, and remove the metal covering
of the desired slot.
3. Securely mount the EVT-PC4-VT2Q and/or EVT-PC4P-JTQ in their respective slots with the provided screw at the
back panel of the computer. Please note that the EVT-PC4-VT2Q and EVT-PC4P-JTQ boards do not need to be
inserted into the PCI (Peripheral Componet Interconnect) slots of the computer motherboard. Then replace the cover
of the computer.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
NOTE: For convenient wiring it is recommended that the DVR cards, EVT-PC4-VT2Q and EVT-PC4P-JTQ, be installed
adjacent to each other as shown on Fig. 2.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating
properly as a result of causes other than defects in material and workmanship.
EVT-PC4-VT2Q Wiring (see Fig. 3) - Video Balun Card
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind
to the purchaser or anyone else.
1. Make sure the maximum distance between the CCTV camera and the DVR card does not exceed 1,950 feet for
monochrome or 1,300 feet for color.
2. Run the UTP cable from the DVR card to where it will be connected to the CCTV camera. Follow the CCTV camera’s
wiring instructions for information on how to safely run and hide this wire.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
NOTE: 1. Individual separate passive video baluns such as SECO-LARM’s EVT-PB1 are required for each camera on the
camera side.
Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
2. The video baluns are polarity-sensitive. Take note of the colors of the positive & negative wires of the video
signal cables as this will be needed when connecting the other end of the UTP cables at the DVR card side.
without the written permission of SECO-LARM.
FILE: D\DTP\MANUAL\MiEVT-PC4_series_07A.pmd
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
3. Use the orange/ orange-white color wire pair of the UTP cable for the video signal. Connect the UTP cables
to the passive video baluns on the camera side and plug the video baluns into the BNC connector of the
CCTV cameras. The EVT-PC4-VT2Q can accomodate a maximum of 4 cameras.
Order Part # 764-027%
PITSW1
E-mail: sales seco-larm.com
@
Download from Www.Somanuals.com. All Manuals Search And Download.
|