OPERATOR’S MANUAL
18 vOLT SPOTLighT
P715
bATTERiES ANd ChARgERS SOLd
SEPARATELy
ACCEPTS ALL ONE+ bATTERy PACKS
Your spotlight has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNiNg: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAvE ThiS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
gENERAL SAFETy RULES
iMPORTANT SAFETy iNSTRUCTiONS
if wrapped or in contact with fabrics, the spotlight lens
can produce sufficient heat to melt some fabrics. To
avoid serious personal injury, never allow the spotlight
lens to come in contact with anything.
WARNiNg!
REAd ANd UNdERSTANd ALL iNSTRUCTiONS. Fail-
ure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
Keep light dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any strong
solvent to clean the spotlight.
don’t expose spotlight to rain. Water entering a power
tool will increase the risk of electric shock or malfunction.
do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the spotlight in unexpected situations. Do not
use on a ladder or unstable support.
WARNiNg!
When using electric appliances, basic precautions should
always be followed, including the following:
Read all the instructions before using the appliance.
To reduce the risk of injury, close supervision is
do not leave the spotlight unattended while in the ON
necessary when an appliance is used near children.
position.
To reduce the risk of electrical shock, do not put
spotlight or charger in water or other liquid. Do not
place or store appliance where it can fall or be pulled into
a tub or sink.
SPOTLighT USE ANd CARE
This product is of household type.
Store spotlight out of the reach of children and other
untrained persons. Spotlights are dangerous in the
hands of untrained users.
Use only the charger supplied by the manufacturer to
recharge.
Let spotlight cool for several minutes after use before
Use only recommended battery pack. Any attempt
to use another battery pack will cause damage to your
spotlight and could possibly explode, cause a fire, or
personal injury.
changing the bulb.
do not use or permit use of spotlight in bed or sleeping
bags. This spotlight lens can melt fabric and a burn injury
could result.
MOdEL
P715
bATTERy PACK
(P104) (Li-ion) 1304ꢀ9001 (P113) 140501001
1304ꢀ900ꢀ 140501005
(P100) (Ni-Cad) 130ꢀ55004 (P110) 14ꢀ3701
ChARgER
SAFETy RULES FOR bATTERy SPOTLighTS
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid gets
in your eyes, flush them with clean water for at least 10
minutes, then seek immediate medical attention.
batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
do not crush, drop or damage battery pack. do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately. Failure to heed this warning can
result in serious personal injury.
130ꢀꢀ40ꢀ8
140ꢀ370ꢀ1,
140ꢀ370ꢀ3
Remove battery pack from spotlight before replacing
bulb or performing any routine maintenance or cleaning.
Replace bulb with same type rated H3 6V55W.
do not disassemble the spotlight.
do not place spotlight or battery pack near fire or
heat. They may explode. Also, do not dispose of a worn
out battery pack by incinerating. Do not incinerate the
battery, even if it is severely damaged or completely worn
out. The battery may explode in fire.
do not operate spotlight or charger near flammable
liquids or in gaseous or explosive atmospheres.
Internal sparks may ignite fumes.
do not store your spotlight in a damp or wet location.
do not store in locations where the temperature is less
than 50°F or more than 100°F. Do not store in outside
sheds or in vehicles.
if the power supply cord is damaged, it must be re-
placed only by the manufacturer or by an authorized
service center to avoid risk.
Risk of burns-do not touch. Risk of fire-keep away
from combustible materials.
do not permit children to use spotlight unsupervised.
It is not a toy. The temperature of the bulb will become
hot after being on for only a short period of time. This hot
temperature can cause burn injury if touched and can
create sufficient heat to melt some fabrics.
The lens gets very hot during use. To reduce the risk of
burns, do not touch hot lens. To reduce the risk of fire, keep
away from combustible materials while in operation.
do not shine spotlight into the eyes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SyMbOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SyMbOL
NAME
dESigNATiON/EXPLANATiON
V
Volts
Voltage
A
Amperes
Minutes
Current
min
Time
Alternating Current
Direct Current
Type of current
Type or a characteristic of current
Rotational speed, at no load
n
o
No Load Speed
Class II Construction
Per Minute
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand operator’s
manual before using this product.
Read The Operator’s Manual
Safety Alert
Precautions that involve your safety.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Hot Surfaces
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SyMbOL
SigNAL
MEANiNg
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
dANgER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNiNg:
CAUTiON:
CAUTiON:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
WARNiNg:
To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely
the Operator’s Manual. If you do not understand the warnings and instructions in the Operator’s Manual, do not use
this product. Call Customer Service for assistance.
SAvE ThESE iNSTRUCTiONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PROdUCT SPECiFiCATiONS
Bulb ..................................................................6 V Halogen
Weight ..................................................................... 1.5 lbs.
LOCK-ON
BUTTON
SWITCH
TRIGGER
Fig. 1
KNOW yOUR SPOTLighT
LOCK-ON bUTTON
The lock-on button is convenient for continuous use for
extended periods of time.
See Figure 1.
Thesafeuseofthisproductrequiresanunderstandingofthe
information on the product and in this operator’s manual as
wellasaknowledgeoftheprojectyouareattempting.Before
use of this product, familiarize yourself with all operating
features and safety rules.
ASSEMbLy
UNPACKiNg
This product requires tag removal.
PACKiNg LiST
Spotlight
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Operator’s Manual
WARNiNg:
Inspect the product carefully to make sure no breakage
If any parts are damaged or missing do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-5ꢀ5-ꢀ579 for assistance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbLy
WARNiNg:
PULL TAB TO
REMOVE
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNiNg:
To prevent accidental starting that could cause serious
personal injury, always remove the battery pack from the
product when assembling parts.
REMOviNg ThE WARNiNg LAbEL
See Figure 2.
The spotlight has a cling-type attached warning label on
the lens. Remove this warning label before use as shown
in figure ꢀ.
Fig. ꢀ
OPERATiON
WARNiNg:
WARNiNg:
The lens gets very hot during use. To reduce the risk of
burns, do not touch hot lens. To reduce the risk of fire,
keep away from combustible materials while in opera-
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
tion
.
WARNiNg:
CAUTiON:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
Operate in a well ventilated area. Do not block vents.
Keep them clear to allow proper ventilation.
This product will accept Ryobi One+ 18 V lithium-ion battery
packs and Ryobi One+ 18 V nickel-cadmium battery packs.
Bothtypesofbatterypacksareshownonthispage.Following
pages will show the lithium-ion 18 V battery pack.
APPLiCATiONS
You may use this product for the purpose listed below:
To illuminate any areas requiring additional light
To illuminate distant objects
For complete charging instructions, refer to the operator’s
manual for the P113 or P110 charger. For battery pack
instructions, see the manual for the P104 lithium-ion battery
pack or the P100 nickel-cadmium battery pack.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATiON
TO iNSTALL bATTERy PACK
See Figures 3 - 4.
Place the switch trigger in the OFF position.
P104 18V LITHIUM-ION
Place the battery pack in the spotlight.
BATTERY PACK
Make sure the latches on each side of the battery pack
snap in place and that battery pack is secured in the
spotlight before beginning operation.
TO REMOvE bATTERy PACK
See Figures 3 - 4.
DEPRESS BOTH
LATCHES TO
RELEASE
Place the switch trigger in the OFF position.
Locate latches on side of battery pack and depress both
sides to release battery pack.
Remove battery pack from the spotlight.
ALIGN RAISED RIB ON
BATTERY PACK WITH
GROOVE IN BATTERY PORT
WARNiNg:
Battery tools are always in operating condition. Therefore,
switch should always be in the OFF position when not in
use or carrying at your side.
P100 18 V NICKEL
CADMIUM
BATTERY PACK
SWiTCh TRiggER
See Figure 4.
To turn the spotlight ON, depress and hold the switch trigger.
To turn it OFF, release the switch trigger.
LOCK-ON bUTTON
See Figure 4.
The spotlight is equipped with a lock-on feature, which
is convenient for continuous use for extended periods of
time.
Fig. 3
To lock-on:
Depress the switch trigger.
Push in and hold the lock-on button, located on the side
of the handle.
Release the switch trigger.
Release the lock-on button.
To release the lock, depress and release the switch
trigger.
WARNiNg:
Never leave the spotlight in the locked-on position and
unattended. Failure to heed this warning could result in
serious injury or property damage.
LOCK-ON
BUTTON
SWITCH
TRIGGER
Fig. 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAiNTENANCE
Install new bulb assembly.
WARNiNg:
Replace bulb retainer pin.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
Hold white connection terminal and reconnect white
lead.
Return the white connection point to its nest.
Align tabs on each side of lens seal with notches on
spotlight housing and seat lens seal in place.
WARNiNg:
Reattach bezel carefully by rotating clockwise.
To avoid serious personal injury, always remove the
battery pack from the product when cleaning or
performing any maintenance.
Tighten securely.
NOTE: Always ask for replacement bulb H3 6V55W,
number 0190ꢀ0001007.
gENERAL MAiNTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
REFLECTOR
LENS
LENS
SEAL
TO
REMOVE
WARNiNg:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
TO
REPLACE
NOTCHES
RIDGE
TABS
REFLECTOR
ASSEMBLY
GROOVE
WHITE
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an Authorized Service Center.
Fig. 5
BEZEL
REPLACiNg bULbS
See Figures 5 - 7.
CONNECTION
POINT
CONNECTION
TERMINAL
REFLECTOR
ASSEMBLY
Overtime, thebulbwillburnout. Whenthisoccurs, replacing
the bulb will be necessary. Be careful not to touch the bulb
glass. This will reduce the life of the bulb.
To replace a bulb:
Remove battery from the spotlight and let it cool for at
least 5 minutes.
Turn the bezel counterclockwise to remove.
Removethereflectorassemblyfromthespotlighthousing.
do not pull on the leads connected to the assembly.
RED
CIRCUIT
LEAD
Remove the white connection point from its nest in the
housing.
RETAINER
PIN
Removethewhiteconnectionterminalfromitsconnection
point.
NOTE: Do not pull white lead without holding the
connection point, as this may damage lead.
CONNECTION
POINT NEST
Remove the retainer pin from the reflector and remove
bulb assembly. Bulb assembly may be rotated in reflector
if needed to aid in removal.
Fig. 6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAiNTENANCE
CAUTiON:
BULB
ASSEMBLY
Do not use a higher rated fuse other than the specified
amperage. This could cause damage to the product.
REPLACEMENT FUSE
See Figure 8.
Ifthespotlightblowsitsfuse, youwillneedtoreplaceit. Look
for replacement fuses where you purchased this product.
Remove the battery pack from the spotlight to access
fuse housing.
RETAINER
PIN
Remove the current fuse and discard. Use a pair of
Fig. 7
fuse pullers if necessary.
Use 10 amp JAT blade type automotive fuse to replace
the blown fuse.
GOOD FUSE
NOTE: Only use 10 amp JAT blade type automotive fuses
for replacement. If second fuse blows, return to authorized
service center for repair. Always ask for replacement fuse
number 0190ꢀ0001013.
FUSE
bATTERiES
This product will accept 18 V lithium-ion batteries or 18 V
nickel-cadmium batteries. Length of service from each
charging will depend on the type of work you are doing.
BLOWN FUSE
The batteries for this product have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
Fig. 8
bATTERy PACK REMOvAL ANd PREPARATiON
FOR RECyCLiNg
To obtain the longest possible battery life, we suggest the
following:
To preserve natural resources, please
recycle or dispose of batteries
properly.
For lithium-ion batteries:
Li - Ion
This product uses nickel-cadmium and
lithium-ion batteries. Local, state or
federal laws may prohibit disposal of
Remove the battery pack from the charger once it is fully
charged and ready for use.
For battery pack storage longer than 30 days:
batteries in ordinary trash.
Store the battery pack where the temperature is below
Consult your local waste authority for
informationregardingavailablerecycling
and/or disposal options.
80°F and away from moisture.
Store battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as
normal.
For nickel-cadmium batteries:
WARNiNg:
Remove the battery pack from the charger once it is fully
Upon removal, cover the battery pack’s terminals with
heavy-duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its compo-
nents. Lithium-ion and nickel-cadmium batteries must
be recycled or disposed of properly. Also, never touch
both terminals with metal objects and/or body parts as
short circuit may result. Keep away from children. Failure
to comply with these warnings could result in fire and/or
serious injury.
charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F.
Store battery packs in a “discharged” condition.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
18 vOLT SPOTLighT
P715
WARNiNg:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
P715
• MODEL NUMBER
• SERIAL NUMBER
• HOW TO OBTAIN REPLACEMENT PARTS:
1-800-5ꢀ5-ꢀ579. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIzED SERVICE CENTER:
1-800-5ꢀ5-ꢀ579.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-5ꢀ5-ꢀ579.
RYOBI® is a registered trademark of Ryobi Limited used under license.
ONE WORLd TEChNOLOgiES, iNC.
14ꢀ8 Pearman Dairy Road, Anderson, SC ꢀ96ꢀ5
Phone 1-800-5ꢀ5-ꢀ579
987000-151
09-ꢀ4-07 (REV:01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|