225R/RD 227R/RD
232R/RD 235R
Operator's Manual
Read through the Operator‘s Manual carefully and
understand the content before using the machine.
101 89 79-26
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Husqvarna AB has a policy of continuous product
development and therefore reserves the right to modify the
design and appearance of products without prior notice.
List of contents
SYMBOL EXPLANATION
Symbols ............................................................................... 2
CONTENTS
List of contents .................................................................... 3
SAFETY INSTRUCTIONS
WARNING!
Under no circumstances may the design
of the machine be modified without the
permission of the manufacturer. Always
use genuine accessories. Non-authorised
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
Personal protective equipment ............................................. 4
The machine‘s safety equipment .......................................... 4
Control, maintenance and service of the machine‘s safety
equipment...................................................................... 7
Cutting equipment ............................................................ 10
General safety instructions ................................................. 11
General working instructions ............................................. 12
Basic clearing techniques.................................................... 13
WHAT IS WHAT?
!
What is what on the brushcutter?....................................... 17
ASSEMBLY
Assembling the handlebars
(225R/RD, 227R/RD, 232R/RD) ............................... 18
Assembling the handlebars (235R) ..................................... 18
Transport position, handlebars ........................................... 18
Assembly of the blade and trimmer head............................ 19
Assembling the blade guard and grass blade ....................... 19
Assembling the blade guard and clearing blade................... 19
Assembling the spray guard and trimmer head
Superauto II (225R/RD, 227R/RD, 232R/RD) ........... 20
Assembling the spray guard and trimmer head
Trimmy SII (235R) ...................................................... 20
Assembling other guards and cutting equipment................ 20
Assembling and dismantling the two-part shaft
(225RD, 227R/RD, 232RD) ....................................... 21
Adjusting the harness and clearing saw ............................... 21
FUEL HANDLING
Fuel ................................................................................... 22
Fuelling.............................................................................. 22
START AND STOP
Control before starting....................................................... 23
Start and stop..................................................................... 23
MAINTENANCE
Carburettor ........................................................................ 24
Muffler .............................................................................. 26
Cooling system .................................................................. 26
Air filter ............................................................................. 27
Angle gear .......................................................................... 27
Two-part shaft.................................................................... 27
Spark plug.......................................................................... 27
Filing the grass blade .......................................................... 27
Sharpening the clearing blade ............................................ 28
Maintenance schedule ........................................................ 28
TECHNICAL DATA
225R/RD........................................................................... 30
227R/RD........................................................................... 30
232R/RD........................................................................... 30
235R.................................................................................. 31
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Personal protective equipment
The machine‘s safety equipment
This section describes the machine‘s safety equipment, its
function and how checks and maintenance are carried out to
ensure that it operates correctly. (See the chapter “What is
what“ to locate where this equipment is positioned on your
machine.)
IMPORTANT INFORMATION
•
Incorrect or careless use of a clearing saw,
brushcutter or trimmer can turn it into a dangerous
tool that can cause serious or even fatal injury to
the operator or others. It is extremely important
that you read and understand the content of this
manual.
WARNING!
Never use a machine with defective safety
equipment. Follow the control,
maintenance and service instructions
described in this section.
•
When using a clearing saw, brushcutter or trimmer,
protective equipment approved by the appropriate
authorities must be used. Personal protective
equipment does not eliminate the risk of accidents,
however, it can reduce the effects of an injury in
the event of an accident. Ask your dealer for help
when choosing protective equipment.
!
1. Throttle trigger
lock
A
The throttle trigger lock is
designed to prevent the
throttle from accidentally
being engaged. When the
HELMET
A helmet should be worn if
trees to be cleared are higher
than 2 metres.
B
trigger lock (A) is pressed
into the handle (= when you
hold the handle) the throttle
(B) is released. When the
grip on the handle is
EAR PROTECTION
Ear protection offering
sufficient dampening effect
should be used.
released the throttle and the
A
throttle trigger lock return
to their original positions.
This takes place via two
independent return spring
systems. This means that the
throttle is automatically
locked in its “idling“
position.
EYE PROTECTION
Blows from branches or
objects thrown by the
rotating cutting equipment
can damage the eyes.
B
GLOVES
Gloves should be worn
when necessary, e.g., when
assembling cutting
equipment.
BOOTS
Use anti-slip and stable
boots.
CLOTHING
Wear clothes made of a
strong fabric and avoid loose
clothing that can catch on
shrubs and branches. Always
wear heavy-duty long pants.
Do not wear jewellery,
shorts, sandals or go
barefoot. Secure hair so it is
above shoulder level.
FIRST AID KIT
A first aid kit should be
carried by operators of
clearing saws, brushcutters
or trimmers.
4– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
2. Stop switch
4. Anti-vibration
system
The stop switch should be
used to stop the engine.
Your machine is equipped
with an anti-vibration system
that has been designed to
give as vibration-free and
comfortable usage as
possible.
The use of incorrectly
wound cord or blunt,
incorrect cutting equipment
(incorrect type or incorrectly
sharpened, see section “Filing
the blade”) increases the level
of vibration.
The machine’s vibration
damping system reduces the
transfer of vibrations
between the engine unit/
cutting equipment and the
machine’s handle unit.
WARNING!
Over exposure to vibrations can result in
!
blood-vessel or nerve injury to persons
suffering with blood circulation problems.
Seek medical attention if you experience
physical symptoms that can be related to
over exposure to vibrations. Examples of
such symptoms are “numbness“, lack of
feeling, “tickling“, “pricking“, “pain“, lack
of or a reduction in normal strength,
changes in the colour of the skin or its
surfaces. These symptoms normally
appear in the fingers, hands or wrists.
3. Cutting
attachment guard
This guard is intended to
prevent objects from being
thrown towards the operator
and to protect the operator
from unintentionel contact
with the cutting attachment.
5. Quick-release
There is an easily accessible,
quick-release catch fitted to
the chest as a safety
precaution in the event of a
fire in the engine or for any
other situation that requires
you to free yourself from the
machine and harness. See the
section “Adjusting the harness
and clearing saw“.
WARNING!
Do not attach any blade to the unit
without proper installation of all required
parts. Failure to use the proper parts can
cause the blade to fly off and seriously
injure the operator and/or bystanders.
!
Under no circumstances may the cutting
equipment be used without an approved
guard fitted. See the chapter “Technical
data”. If the wrong guard or a defective
guard is fitted this can cause serious
personal injury.
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
6. Muffler
7. Cutting
equipment
1
The muffler is designed to
give the lowest possible noise
level and to direct the
engine‘s exhaust fumes away
from the operator. Muffler
fitted with catalytic
1) Clearing blades are
intended for cutting wood.
converter is also designed to
reduce harmful exhaust
components.
2
2) Grass blades are
intended for brush cutting.
In countries that have a
warm and dry climate the
risk of fire is obvious. We
have therefore fitted certain
mufflers with a spark arrest
screen. Make sure that your
muffler is fitted with this
kind of screen.
3
3) The trimmer head is
intended for trimming
grass.
It is extremely important
that the instructions for
checking, maintaining and
servicing the muffler are
followed. (See the section
“Control, maintenance and
service of the machine‘s safety
equipment“.)
8. Locking nut
A locking nut is used to
secure some types of cutting
equipment on the output
shaft.
WARNING!
Mufflers fitted with catalytic converters
become extremely hot during use and
after stopping. This also applies at idling
speeds. Contact can result in burns to
the skin. Be observant to the risk of fire!
!
!
WARNING!
Bear in mind that exhaust fumes:
• contain carbon monoxide, which can
cause carbon monoxide poisoning.
Therefore never start or run the machine
indoors.
• are hot and can contain sparks that can
cause fires. Never start the machine
indoors or close to inflammable material.
6– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
• See section "Start". Start
the machine and apply full
throttle. Release the
Control, maintenance and service of
the machine‘s safety equipment
throttle and check that the
cutting equipment stops
and remains at a standstill.
If the cutting equipment
rotates with the throttle in
the idling position then
the carburettor‘s idling
setting must be checked.
See chapter
IMPORTANT INFORMATION
• All service and repairs to the machine require
special training.
• This applies especially to the machine‘s safety
equipment. If the machine does not meet any of the
controls listed below you should contact your
service workshop.
“Maintenance“.
• The purchase of one of our products guarantees
that professional repair and servicing will be
carried out on it. If the point of purchase is not one
of our servicing dealers, please ask for details of
the closest service workshop.
1. Throttle trigger
lock
• Check that the throttle is
locked in the “idling
position“ when the
throttle trigger lock is in
its original position.
• Press in the throttle
trigger lock and make sure
it returns to its original
position when released.
• Ensure that the throttle
and throttle trigger lock
move easily and that their
return spring systems
function.
2. Stop switch
• Start the engine and make
sure that the engine stops
when the stop switch is
moved to the stop
position.
The throttle trigger lock is
designed to prevent the
throttle from accidentally
being engaged. When the
trigger lock (A) is pressed
A
into the handle (= when you
hold the handle) the throttle
(B) is released. When the
grip on the handle is
B
released the throttle and the
throttle trigger lock return
to their original positions.
This takes place via two
independent return spring
systems. This means that the
throttle is automatically
locked in its “idling“
position.
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
3. Cutting
5. Muffler
attachment guard
1.Never use a machine that
has a defective muffler.
• Check that the guard is
undamaged and not
cracked.
2.Check regularly that the
muffler is secure.
• Replace the guard if it has
been exposed to impact or
is cracked.
3.If your muffler is fitted
with a spark arrest screen
then it should be cleaned
regularly. A blocked
screen leads to the engine
overheating with serious
damage as a result. Never
use a muffler with a
• Always use the prescribed
blade an guard
combination, see chapter
"Technical data".
defective spark arrest
screen.
4. Vibration
damping system
• Check the vibration
damping element
regularly for material
cracks and distortion.
• Check that the vibration
damping element is
undamaged and securely
attached.
8– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
6. Cutting equipment
7. Quick-release
This section describes how through correct maintenance and
through using the right type of cutting equipment you can:
• Reduce the machine‘s tendency to kickback
• Obtain maximum cutting capacity.
• Increase the service life of the cutting equipment.
• Check that the harness
straps are correctly
positioned. When the
harness and machine are
adjusted, check the harness‘
safety release catch to
ensure it works correctly.
Four basic rules:
1)Only use the cutting
and guard equipment
we recommend! See
chapter “Technical
data“.
2)Keep the blade‘s teeth
well and correctly
sharpened! Follow our
instructions and use the
recommended filing
gauge. An incorrectly
sharpened or damaged
blade increases the risk
of an accident.
8. Locking nut
• Protect your hand from
injury when assembling,
use the blade guard as
protection when tightening
with a socket spanner.
Tighten the nut by turning
against the direction of
rotation. Loosen the nut by
turning in the direction of
rotation. (NOTE! the nut
has a left-hand thread).
3)Keep the correct setting.
Follow our instructions
and use the
recommended setting
tool. An incorrectly set
blade increases the risk
of jamming and
• Tighten the nut using a
socket spanner, 35 - 50
Nm (3.5 - 5 kpm).
kickback.
NOTE!
The locking nut‘s nylon lock
must not be so worn that it
can be turned by hand. The
lock shall hold at least 1.5
Nm. The nut should be
replaced after it has been put
on approx. 10 times.
4)Check the cutting
equipment with regard
to damage and crack
formation. Damaged
cutting equipment
should always be
replaced.
WARNING!
Never use a machine with defective
!
safety equipment. The safety equipment
should be maintained as described in this
section. If your machine does not meet
any of these controls you should contact
your service workshop.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Sharpening the
grass blade
Cutting equipment
IMPORTANT INFORMATION
• See the cutting
equipment’s packaging for
correct filing instructions.
The section describes how through correct mainte-
nance and through using the right type of cutting
equipment you can reduce the machine‘s tendency to
kickback, obtain maximum clearing capacity and
increase the service life of the cutting equipment.
• The blades are sharpened
using a single cut flat file.
•
Only use the cutting and guard equipment we
recommend! See chapter “Technical data“.
• Sharpen all edges equally
to maintain the balance of
the blade.
•
Refer to the instructions for the cutting
equipment for the correct winding of cord
and for the selection of the right cord diameter.
•
•
Keep the blade’s teeht well and correctly
sharpened! Follow our recommendations. Also
refer to the instructions on the blade packaging.
Trimmer head
Maintain the correct setting. Follow our instruc-
tions and use the recommended filing gauge.
• Only use a trimmer head
and trimmer cord that is
recommended. These
have been tested by the
manufacturer to suit a
particular engine size.
This is especially
important when a fully
automatic trimmer head
is used. Only use the
cutting equipment we
recommend! See chapter
“Technical data“.
WARNING!
Incorrect cutting equipment or an
incorrectly sharpened blade increases
the risk of kickback.
!
Sharpening the
clearing blade
• See the cutting
equipment’s packaging for
correct filing instructions.
• Generally smaller machines require a small trimmer head
and vice versa. This is because when clearing using a cord
the engine must throw out the cord radially from the
trimmer head and also meet resistance from the grass being
cleared.
• A correctly sharpened
blade is a prerequisite for
working efficiently and to
avoid unnecessary wear to
the blade and clearing saw.
• Make sure that the blade is
well supported when you
use the file. Use a 5,5 mm
round file with a file
holder.
• The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of the
same diameter.
• Make sure the knife positioned on the trimmer guard is
intact. This is used to cut the cord to the correct length.
• The sharpening angle is
15°. Every other tooth is
sharpened to the right and
the intermediate tooth to
the left. When the blade
has been heavily pitted by
stones the upper side of
the teeth can, in
exceptional cases, need to
be dressed using a flat file.
In such cases this takes
place before sharpening
with the round file.
• To increase the life of the cord it can be soaked in water for
a few days. This will make the line tougher and it will keep
longer.
IMPORTANT INFORMATION
Always ensure the trimmer cord is wound tightly
and evenly around the drum, otherwise harmful
vibrations will occur.
WARNING!
Always stop the engine before starting
work on any part of the cutting equipment.
!
Dressing the top side must
be carried out equally for
all teeth.
This continues to rotate even after the
throttle has been released. Ensure that the
cutting equipment has stopped completely
and remove the cable from the spark plug
before you start to work on it.
• Adjust the setting. This
should be 1 mm.
10– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Fuel safety
General safety instructions
IMPORTANT INFORMATION
• Never fill the machine
while the engine is
running. Always stop the
engine and let it cool for a
few minutes before
refuelling.
•
The machine is only designed for trimming grass,
brush cutting and/or forestry clearing.
•
The only accessories to be used with the engine
unit as a drive source are the cutting units we
recommend in the chapter “Technical data“.
•
Never use the machine if you are tired, if you have
consumed alcohol, or if you are taking medicines
that can affect your sight, your judgement or the
control of your body.
• Provide good ventilation
when filling or mixing fuel
(petrol and 2-stroke oil).
Min. 3 m
(10 ft)
•
•
Use personal protective equipment. See the
section “Personal protective equipment“.
• Move the machine at least
3 m from the filling
position before starting.
Never use a machine that has been modified so
that it no longer corresponds with the original
design.
•
Never use a machine that is faulty. Follow the
maintenance, control and service instructions in
this Operator‘s Manual. Some maintenance and
service actions should be carried out by trained
and qualified specialists. See the chapter “Mainte-
nance“.
• Never start the machine:
a)If you have spilt fuel on it.
Wipe up all spillage.
b)If you have spilt fuel on
yourself or your clothes.
Change your clothes.
•
The machine operator shall ensure, while working,
that no persons or animals come closer than 15
metres (50 feet). When several operators are
working in the same area the safety distance
should be at least double tree length, however, at
least 15 metres (50 feet).
c)If there is a fuel leak.
Make regular checks for
leakage from the fuel cap
and the fuel supply pipes.
WARNING!
Faulty cutting equipment or an incorrectly
!
sharpened blade increases the risk of
accidents.
Transport and storage
Start
• Store and transport the machine and fuel so that any leakage
or fumes do not risk coming into contact with sparks or
naked flames. For example, electric machines, electric
motors, electrical switches/power switches, heaters or the
like.
WARNING!
When the engine starts with the choke lever
in the choke or starter throttle position the
cutting equipment starts to rotate
immediately.
!
• The complete clutch cover
with shaft must be fitted
• When storing and transporting fuel approved containers
intended for this purpose must be used.
before the machine is
started, otherwise the
clutch can become loose
and cause personal injury.
• When storing the machine for long periods the fuel tank
must be emptied. Contact your local petrol station to find
out how to dispose of excess fuel.
• Never start the machine
indoors. Bear in mind the
dangers of inhaling the
• Always keep the transport guard attached when transporting
and storing the machine.
engine‘s exhaust fumes.
• Observe your surroundings
and make sure that there is
no risk of people or
animals coming into
contact with the cutting
WARNING!
Exercise great care when handling fuel.
Bear in mind the risk of fire, explosions and
inhaling fumes.
!
equipment.
• Place the machine on the ground, ensure the cutting
equipment runs free of twigs and stones. Push the machine
body towards the ground using your left hand. (NOTE! Not
with your foot). Grip the starter handle with your right hand
and pull the starter cord.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
4.Take great care when
General working instructions
cutting a tree that is subject
to tension. A tree that is
under tension can spring
back to its original position
both before and after being
cut. Incorrect positioning
on your behalf or when
positioning the cut can
result in the tree hitting you
or the machine so that you
lose control. Both situations
can cause serious personal
injury.
IMPORTANT INFORMATION
•
•
This section takes up the basic safety precautions
for working with the clearing saw and trimmer.
If you encounter a situation where you are
uncertain how to proceed you should ask an
expert. Contact your dealer or your service
workshop.
•
•
Avoid all usage which you consider to be beyond
your capability.
You must understand the difference between
clearing, brush cutting and grass trimming before
using the machine.
5.The engine should be
switched off before moving.
When moving over longer
distances and transporting
the transport guard should
be used.
Basic safety precautions
1.Observe your surroundings:
6.Never put the machine
down with the engine
running unless you have
good sight of it.
• To ensure that people, animals or other things cannot affect
your control of the machine.
• To ensure that the above mentioned do not come into
contact with the cutting equipment or objects that can be
thrown by the cutting equipment.
• NOTE! Never use a machine without the possibility of
calling for help in the event of an accident.
2.Avoid usage in
unfavourable weather
conditions. For example,
thick fog, heavy rain,
strong winds or extreme
cold, etc. To work in bad
weather conditions is
tiring and can create
dangerous circumstances,
e.g. slippery surfaces,
affect a tree‘s direction of
fall, etc.
3.Make sure you can walk
and stand safely. Look out
for any obstacles with
unexpected movement
(roots, stones, branches,
pits, ditches, etc.). Take
great care when working
on sloping ground.
12– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Adjusting the harness and clearing saw
Basic clearing techniques
WARNING!
• Always carry out clearing and trimming at full throttle.
When working with the clearing saw it
should always be hooked in the harness. If
this is not done, you cannot control the
clearing saw safely and this can result in
injury to yourself or someone else. Never
use a harness with a defective quick
release catch.
!
• Always drop to idling speed after each working operation.
Longer periods running at full throttle without loading the
engine (that is without resistance, which the engine feels
from the cutting equipment when trimming) can lead to
serious engine damage.
Quick release
Designations
On the front is an easily
accessible, quick release
catch. Use this if the engine
should catch fire or in any
other emergency situation
when you quickly need to
take off the harness and
machine.
• Forestry clearing is a
general term for cutting
small trees where each
stem is cut individually.
A saw blade is used.
• Brush cutting is a general
term for clearing grass.
Grass blades are used for
this purpose.
Even load on the
shoulders
A well-adjusted harness and
clearing saw significantly
facilitates working. Adjust
the harness for the best
working position. Tension
the side straps so that the
weight is evenly distributed
across the shoulders.
• Grass trimming is a
general term for light
clearing, e.g. around
edges or around trees. A
trimmer head or plastic
blade is used.
Correct height
1) Forestry clearing
Adjust the carrier strap so
that the suspension hook
comes approximately 10
cm under the hip. The
blade should be angled
forward a little.
WARNING!
Sometimes branches, grass or wood can
get caught between the guard and cutting
equipment. Always stop the engine when
cleaning.
!
2)Grass clearing
The suspension hook
should hang
approximately 20 cm
under the hip so that the
blade is parallel to the
ground.
Correct balance
1)Forestry clearing
Move the suspension eye
forwards or backwards. If
the blade is balanced a 10-
20 cm above the ground it
is easier to avoid stones.
2)Grass clearing
Let the blade balance at a
comfortable clearing
height, i.e. close to the
ground.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Clearing‘s ABC
Forestry clearing
using a saw blade
A.
B.
C.
D.
E.
Always use the correct equipment.
Always have well adjusted equipment.
Follow the safety instructions.
Organise the work well.
Always use full throttle when applying the blade.
Always use a sharp blade.
• When applying the blade
to heavier stems the risk of
kickback increases. You
should therefore avoid
applying the blade on the
cutting area between 12
and 3 o‘clock.
F.
G.
H.
Avoid stones.
Guide the direction of fall (use the wind).
• To fell to the left, the
lower section of the tree
should carry to the right.
Angle the blade and move
it with a resolute
movement diagonally
down to the right. At the
same time press against the
stem using the blade
WARNING!
Avoid cutting in the cutting region
between 12 and 3 o‘clock on the blade.
Kickback can occur due to the blade‘s
rotation speed in this area of the blade
when applied on thick stems.
!
Working methods
• Before you start clearing, check the clearing area, its
condition, slopes, if there are stones, pits, etc.
guard. Apply the blade on
the area between 3-5
• Thereafter start at the end which is easiest, and make a good
start to the clearing.
o‘clock. Use full throttle
when applying the blade.
• Work systematically to
and from and across the
area. Each stroke should
encompass a working
area of 4-5 metres. This
then utilises the full
• To fell to the right, the
lower section of the tree
should carry to the left.
Angle the blade and move
it with a resolute
working area of the
machine in both
directions and provides
the operator with an easy
and variable working
area to work through.
movement diagonally up
to the left. Apply the blade
on the area between 3 and
5 o‘clock so that the
blade‘s direction of
• The length of the
pathway should be
approx. 75 m. Move the
fuelling station as work
progresses.
rotation carries the lower
section of the tree to the
left.
• On sloping ground the
pathway should run
parallel to the slope. It is
far easier to work along a
slope then up and down
a slope.
• The pathway should be
planned so that you
avoid going over ditches
or other obstacles. Also
adapt the pathway to the
wind conditions so that
the cleared stems fall on
the part of the stand that
has been cleared.
• To fell a tree forwards the
lower section of the tree
should be drawn
backwards. Draw the blade
backwards with a quick
and resolute movement.
14– English
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
• Large stems must be cut
from two sides.
Brush cutting using a grass blade
Determine in which
direction the stem
• A blade is used for all
types of high or thick
grass.
should fall. First apply
the saw to the felling
side. Then cut from the
other side to fell the
stem. The feed pressure
should be applied with
regard to the size of the
stem‘s hardness. Small
stems require more
pressure, while large
stems require less
• The grass is cut down
with a sideways, swinging
movement, where the
movement from right-to-
left is the clearing stroke
and the movement from
left-to-right is the return
stroke. Let the blade work
on the left-hand side
(between 8 and 12
pressure.
o’clock).
• If the stems are tightly
packed adapt the
through-speed with this
in mind.
• If the blade is angled to the left when clearing the grass will
collect in a line, which makes collection easier, e.g. when
raking.
• If the blade should jam in the stem, never jerk the
machine free. If you do this the blade, angle gear, shaft or
the handlebars can be damaged. Release the handlebars
and grip the shaft with both hands and slowly pull the
machine free.
• Try to work rhythmically. Stand firmly with your feet apart.
Move forward after the return stroke and stand firmly again.
• Let the support cup rest lightly against the ground. It is used
to protect the blade from hitting the ground.
• Reduce the risk of material wrapping around the blade by
following these instructions:
a) Always work at full throttle.
b) Avoid the previously cut material during the return
stroke.
Brush cutting
using the saw
blade
• Thin stems and brush are
mown down. Work by
swinging the machine
sideways.
• Stop the engine and remove the brushcutter from the
harness before you start to gather the cut material.
• Try to cut several stems in
one movement.
WARNING!
Neither the user of the tool or anyone else
may attempt to remove the cut material
!
• With groups of hardwood
stems, first clear around
the group. Cut high on
the stems around the
outside of the group to
avoid jamming. Now cut
the stumps to the
while the engine is running or with the
blade rotating as this can result in serious
injury.
Stop the engine and blade before you
remove material that has wound around the
blade as otherwise there is a risk of injury.
required height. Now try
to come in with the blade
and cut from the centre of
the group. If it is still
difficult to gain access, cut
long stumps and let the
stems fall down. This will
reduce the risk of
WARNING!
Beware of thrown objects. Always wear eye
protection. Never lean over the guard.
!
Stones, rubbish etc. can be thrown up into
the eyes resulting in blindness or other
serious injury.
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be outside the safety zone of 15
meters (50 feet). Stop the machine
immediately if anyone approaches.
jamming.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Trimming
Grass clearing
using the trimmer
head
• The trimmer is ideal to
cut grass that is difficult
to reach using a normal
lawn mower. Keep the
cord parallel to the
ground when cutting.
Avoid pressing the
trimmer head against the
ground as this can ruin
the lawn and damage the
tool.
• Hold the trimmer head
just above the ground at
an angle. It is the end of
the cord that carries out
the work. Let the cord
work at its own pace.
Do not press the cord
into the area to be cut.
• Do not allow the
trimmer head to
• The cord can easily
remove grass and weeds
up against walls, fences,
trees and borders,
however, it can also
damage sensitive bark on
trees and bushes and
damage fence posts.
constantly come into
contact with the ground
during normal cutting
procedures. Constant
contact can cause damage
and wear to the trimmer
head.
• Reduce the risk of
damaging plants by
shortening the cord to
10-12 cm and reducing
the engine speed.
Sweeping
• The rotating cord‘s
fanning effect can be
used for quick and easy
cleaning. Hold the cord
parallel to and above the
area to be swept and
move the trimmer from
side to side.
Clearing
• The clearing technique
removes all unwanted
vegetation. Keep the
trimmer head just above
the ground and tilt it.
Let the end of the cord
strike the ground around
trees, posts, statues and
the like. NOTE! This
technique increases the
wear on the cord.
• When cutting and
sweeping you should use
full throttle to obtain the
best results.
• The cord wears quicker
and must be fed forward
more often when
working against stones,
brick, concrete, metal
fences, etc. than when
coming into contact
with trees and wooden
fences.
WARNING!
Beware of thrown objects. Always wear eye
!
protection. Never lean over the guard.
Stones, rubbish etc. can be thrown up into
the eyes resulting in blindness or other
serious injury.
Keep unauthorised persons at a distance.
Children, animals, onlookers and helpers
should be outside the safety zone of 15
meters (50 feet). Stop the machine
immediately if anyone approaches.
• When trimming and
clearing you should use
less than full throttle so
that the cord lasts longer
and to reduce the wear
on the trimmer head.
16– English
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
23
27
28
30
What is what on the brushcutter?
17. Clutch cover
18. Handlebar adjustment
19. Locking nut
20. Support flange
21. Support cup
22. Drive disc
1. Blade
2. Grease filler cap
3. Angle gear
4. Blade guard
5. Shaft
6. Handlebars
7. Throttle
23. Trimmer head
24. Shaft coupling
25. Socket spanner
26. Operator‘s Manual
27. Transport guard
28. Allen key
8. Stop switch
9. Throttle trigger lock
10. Suspension for clearing saw
11. Cylinder cover
12. Starter handle
13. Fuel tank
30. Locking pin
31. Harness
14. Choke
32. Spray guard
15. Air purge
16. Air filter cover
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the handlebars
(225R/RD, 227R/RD, 232R/RD)
Assembling the handlebars (235R)
• Remove the screw at the
rear of the throttle handle.
• Remove the screw at the
rear of the throttle
handle.
• Slide on the throttle handle
on the right-hand side of
the handlebars, (see the
diagram).
• Slide on the throttle
handle on the right-hand
side of the handlebars,
(see the diagram).
• Align the hole in the
throttle handle for the
fixing screw with the hole
on the handlebars.
• Align the hole in the
throttle handle for the
fixing screw with the
hole on the handlebars.
• Refit the screw in the rear
of the throttle handle.
• Refit the screw in the
rear of the throttle
handle.
• Fit the screw through the
throttle handle and the
handlebars and tighten.
• Fit the screw through the
throttle handle and the
handlebars and tighten.
• Unscrew the bracket
components from the
handlebar bracket.
• Unscrew the handle
from the handlebar
bracket.
• Position the handlebars as
shown. Fit the bracket
components and tighten the
handle lightly.
• Position the handlebars
as shown. Fit the bracket
components and tighten
the handle lightly.
• Fit the cabling as shown.
• Put on the harness and
hang the machine in the
suspension hook. Now
finely adjust so that the
machine gives a
comfortable working
position when it‘s attached
to the harness. Tighten the
handle.
• Put on the harness and
hang the machine in the
suspension hook. Now
finely adjust so that the
machine gives a
comfortable working
position when it‘s
attached to the harness.
Tighten the handle.
Transport position, handlebars
• The handlebars can easily
be turned to fit along the
shaft for easy
transportation and storage.
• Loosen the knob. Turn the
handles clockwise so that
the throttle comes against
the engine.
• Thereafter fold the
handlebars around the
shaft. Tighten the handle.
• Attach the transport
guard.
18– English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly of the blade and trimmer
head
Assembling the blade guard and
clearing blade
It is extremely important that
the disc drive’s/support
flange’s guide engages
correctly in the cutting
equipment’s centre hole when
assembling the cutting
equipment. Cutting
equipment assembled
incorrectly can result in
serious and/or fatal personal
injury.
•Fasten the bracket(H)
using the four screws (I).
• The guard (A) is fitted
using 4 screws (L) as set
out in the diagram.
NOTE! Use the
recommended blade
guard.
I
H
• Fit the drive disc (B) on
the output axle.
WARNING!
Do not attach any blade to the unit
• Turn the blade axle until
one of the holes in the
drive disc aligns with the
hole in the gear housing.
!
without proper installation of all required
parts. Failure to use the proper parts can
cause the blade to fly off and seriously
injure the operator and/or bystanders.
L
Under no circumstances may the cutting
equipment be used without an approved
guard fitted. See the chapter “Technical
data”. If the wrong guard or a defective
guard is fitted this can cause serious
personal injury.
• Insert the locking pin (C)
in the hole so that the
axle is locked.
• Place the blade (D) and
A
support flange (F) on the
IMPORTANT INFORMATION
output axle.
The machine must be equipped with the correct
handlebars, blade guard and harness if either a
clearing blade or grass blade are to be used.
• Fit the nut (G). The
G
tightening torque of the
nut is 35-50 Nm (3.5 - 5
kpm). Use the socket
spanner in the tool kit.
Hold the handle of the
spanner as close to the
blade guard as possible.
The nut is tightened
when the spanner is
turned against the
F
Assembling the blade guard and
grass blade
D
• The guard (A) is fitted
using 4 screws (L) and the
support plate (M) as set
out in the diagram.
NOTE! Use the
recommended blade
guard.
• Fit the drive disc (B) on
the output axle.
• Turn the blade axle until
one of the holes in the
drive disc aligns with the
hole in the gear housing.
• Insert the locking pin (C)
in the hole so that the axle
G
F
B
E
D
direction of rotation (left-
hand thread).
C
A
B
• When slacking off and
tightening the saw blade
nut, the hands may be
injured by the blade
teeth. Always hold your
hand protected by the
blade guard. This is
facilitated by the use of a
long box spanner. The
illustration shows the area
in which you should keep
the box spanner.
C
L
M
is locked.
• Place the blade (D),
support cup (E) and
support flange (F) on the
output axle.
• Fit the nut (G). The
tightening torque of the
nut is 35-50 Nm (3,5 - 5
kpm). Use the socket spanner in the tool kit. Hold the
handle of the spanner as close to the blade guard as possible.
The nut is tightened when the spanner is turned against the
direction of rotation (left-hand thread).
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling the spray guard and
trimmer head Superauto II
Assembling the spray guard and
trimmer head Trimmy SII (235R)
(225R/RD, 227R/RD, 232R/RD)
• Fit the guard (A) intended
for use with the trimmer
head. Secure using four
bolts (L) and the support
plate (M) as shown in the
diagram.
• Fit the guard (A) intended
for use with the trimmer
head. Secure using the 4
bolts (L) and the support
plate (M) as set out in the
diagram.
A
L
B
• Fit the driver plate (B) on
the drive shaft.
K
• Fit the drive disc (B) on the
output axle.
J
• Rotate the drive shaft so
that one of the holes in the
driver plate lines up with
the corresponding hole in
the gear housing.
I
• Turn the blade axle until
one of the holes in the
drive disc aligns with the
hole in the gear housing.
C
M
K
• Insert the locking pin (C)
into the hole to lock the
shaft.
• Insert the locking pin (C)
H
in the hole so that the axle
is locked.
G
• Screw on the trimmer
head (H) in the opposite
direction to the normal
direction of rotation.
F
B
C
I
• The trimmer head must be
split to be fitted (see the
diagram). Proceed as
follows:
M
L
• Tighten the trimmer head
to a torque of 35-50 Nm
(3.5-5 kpm).
• Insert your finger into the
centre hole of the cover (I)
at the same time as you
hold the cover with your
other fingers. Press the two
catches (J) that extend from
the cut-out on the bottom
section (K) using the
• To remove the trimmer
head just reverse the
sequence.
A
Assembling other guards and
cutting equipment
thumb and index finger of
your other hand. Press
apart the trimmer head
using the fingers on the
cover.
• Fit the guard (A)
intended for use with
the trimmer head.
Secure using four bolts
(L) and the support plate
A
L
B
(M) as shown in the
diagram.
• Place the cover (I) and the
support flange (F) on the
output axle.
• Fit the disc drive (B) on
the output axle.
C
M
• Fit the nut (G). The
tightening torque of the
nut is 35-50 Nm (3,5-5
kpm). Use the socket
spanner in the tool kit.
Hold the handle of the
spanner as close to the trimmer guard as possible. The nut is
tightened when the spanner is turned against the direction of
rotation (left-hand thread).
• Turn the blade axle until
one of the disc drive’s
holes aligns with the
corresponding hole in
the gear housing.
H
• Insert the locking pin
(C) into the hole to lock
the axle.
• Screw on the trimmer
head (H) in the
direction of rotation.
• Fit the trimmer head‘s bottom section (K) on the cover (I)
by pressing the two sections together with the cut-outs on
the bottom section aligned with the catches on the cover.
• Dismantling takes place
in the reverse order.
• To dismantle follow the instructions in the reverse order.
20– English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembling and dismantling the
two-part shaft (225RD, 227RD,
232RD)
Adjusting the harness and clearing
saw
WARNING!
When working with the clearing saw it
should always be hooked in the harness.
Assembling:
!
If this is not done, you cannot control the
clearing saw safely and this can result in
injury to yourself or someone else. Never
use a harness with a defective quick
release catch.
• Make sure the handle is
loose.
• Guide the cut-out on the
lower section of the shaft
into the coupling‘s
Quick release
On the front is an easily
accessible, quick release
catch. Use this if the engine
should catch fire or in any
other emergency situation
when you quickly need to
take off the harness and
machine.
locking plate on the
upper section of the
shaft. The sections are
then locked together.
• Tighten the handle.
Even load on the
shoulders
A well-adjusted harness and
clearing saw significantly
facilitates working. Adjust
the harness for the best
working position. Tension
the side straps so that the
weight is evenly distributed
across the shoulders.
Dismantling
• Undo the handle (at least
three turns).
• Press the handle towards
the coupling.
• Carefully twist the lower
section out of the lock.
Correct height
1) Forestry clearing
Adjust the carrier strap so
that the suspension hook
comes approximately 10
cm under the hip. The
blade should be angled
forward a little.
• Hold both parts of the
shaft and pull out the
lower section from the
coupling.
2)Grass clearing
The suspension hook
should hang
approximately 20 cm
under the hip so that the
blade is parallel to the
ground.
Correct balance
1)Forestry clearing
Move the suspension eye
forwards or backwards. If
the blade is balanced a 10-
20 cm above the ground it
is easier to avoid stones.
2)Grass clearing
Let the blade balance at a
comfortable clearing
height, i.e. close to the
ground.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixture
Fuel
NOTE!
• Always mix petrol and oil in a clean container intended for
petrol.
The machine is fitted with a two-stroke engine and must
always be run on a mixture of petrol and two-stroke oil. It is
important to measure the quantity of oil accurately, to ensure
the correct mixture ratio. Small discrepancies in the amount of
oil have a great bearing on the proportions of the fuel mixture
when mixing small amounts of fuel.
• Always start by filling half the quantity of petrol required.
Then add the entire oil quantity. Mix (shake) the fuel
mixture. Fill the remaining quantity of petrol.
• Mix (shake) the fuel mixture carefully before filling in the
machine‘s fuel tank.
• Do not mix more than max. one month’s supply of fuel.
• If the machine is not used for a long period of time, the fuel
tank should be emptied and cleaned.
WARNING!
Always provide good ventilation when
handling fuel.
!
Petrol
WARNING!
The catalytic converter muffler gets very hot
during and after use.This also applies
during idling. Be aware of the fire hazard,
especially when handling the saw near
flammable substances or vapours.
!
NOTE!
Always use an oil-mixed
quality petrol (at least 90
octane). If your machine is
equipped with a catalytic
converter, (see “technical
data”) an unleaded, oil
mixed quality petrol should
always be used. A leaded
petrol will destroy the
catalytic converter.
Fuelling
WARNING!
The following precautions reduce the risk
of fire:
!
Do not smoke or place any sources of heat
in the vicinity of the fuel. Never refuel
when the engine is running. Always stop
the engine and let it cool for a few minutes
before refuelling. Open the fuel cap slowly
when fuelling so that any over pressure is
released slowly.Tighten the fuel cap
carefully after refuelling. Always move the
machine from the fuelling place before
starting.
• The lowest recommended
octane rating is 90. If you
run the engine on a petrol
with a lower octane rating
than 90 so-called
“knocking“ can occur.
This leads to an increased
engine temperature, which
can result in a serious
engine breakdown.
• Clean around the fuel
cap. Contamination in
the tank can disrupt
operations.
• When working at
continuous high revs a
higher octane rating is
recommended.
• Ensure that the fuel is
well mixed by shaking the
container before filling
the tank.
Two-stroke oil
Min. 3 m
(10 ft)
• For the best results use
HUSQVARNA two-stroke
oil, which has been
specially produced for
clearing saws and chain
saws.
Gasolin
Benzin
Essence
Gasolina
Lit.
Oil • Öl
Huile • Aceite
Lit.
Mixing ratio 1:50 (2%).
• If HUSQVARNA two-stroke oil is not available you can use
a high quality two-stroke oil intended for air cooled engines.
Contact your dealer when selecting an oil.
Mixing ratio: 1:33 (3%).
• Never use two-stroke oil intended for water cooled outboard
motors, so-called outboard motor oil.
2% (1:50)
3% (1:33)
0,15
0,10
0,20
0,30
0,40
5
0,30
10
15
20
0,45
0,60
US
gallon
US
fl. oz.
2% (1:50)
2 1/2
6 1/2
3% (1:33)
3 3/4
9 3/4
1
2 1/2
5
• Never use oil intended of four-stroke engines.
12 7/8
19 1/4
22– English
Download from Www.Somanuals.com. All Manuals Search And Download.
START AND STOP
Cold engine
IGNITION: Set the stop
Control before starting
switch to the start position.
CHOKE: Set the choke
control in the choke
position.
AIR PURGE: Press the air
purge diaphragm repeatedly
until fuel begins to fill the
diaphragm. The diaphragm
need not be completely
filled.
For reasons of safety follow
these recommendations!
• Check the blade to ensure
that no cracks have formed
at the bottom of the teeth
or by the centre hole. The
most common reason why
cracks are formed is that
sharp corners have been
formed at the bottom of
the teeth while sharpening
or that the blade has been
used with dull teeth.
Discard a blade if cracks
are found.
• Check that the support
flange is not cracked due
to fatigue or due to being
tightened too much.
Warm engine
Use the same starting
procedure as for the cold
engine, but do not set the
choke control in the choke
position. The start throttle
position is obtained by
setting the choke control in
the choke position and then
returning it to its original
position.
Discard the support flange
if it is cracked.
• Ensure the locking nut has
not lost its captive force.
The nut lock should have
a locking force of at least
1.5 Nm. The tightening
torque of the locking nut
should be 35-50 Nm.
Stop
The engine is stopped by
switching off the ignition.
• Check that the guard is
not damaged or cracked.
Replace the guard if it is
exposed to impact or is
cracked.
• Check that the trimmer
head and spray guard are
not damaged or cracked.
Replace the trimmer head
or spray guard if they are
exposed to impact or are
cracked.
WARNING!
When the engine is started with the choke
in the choke or start position the cutting
equipment starts to rotate immediately.
!
Start
Press the machine body
against the ground using
your left hand (NOTE! Not
your foot). Grip the starter
handle, slowly pull out the
cord with your right hand
until you feel some
• Never use the machine without a guard or spray guard nor
with a defective guard.
resistance (the starter pawls
grip), now quickly and
Start and stop
powerfully pull the cord.
Reset the choke control as
soon as the engine fires and
repeat until the engine starts.
When the engine starts
quickly apply full throttle
and the start throttle will
automatically disengage.
NOTE! Do not pull the
starter cord out completely
and do not release the starter
cord from the fully extended
position. This can damage
the machine.
WARNING!
The complete clutch cover with shaft must
be fitted before the machine is started,
otherwise the clutch can become loose
and cause personal injury.
Always move the machine from the filling
area before starting. Place the machine on
a flat surface. Ensure the cutting
equipment cannot come into contact with
any object. Make sure no unauthorised
persons are in the working area,
otherwise there is a risk of serious
personal injury.The safety distance is 15
metres.
!
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Basic setting
Carburettor
• The carburettor is set to its basic setting when test run at the
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
factory. The basic setting should be kept during the
machine‘s first working hours. Thereafter the carburettor
should be finely adjusted. Fine adjustment should be carried
out by a skilled technician.
After your unit has been run 8-10 tanks of fuel the engine
has broken in. To ensure that your unit is at peak
performance and producing the least amount of harmful
emissions after break in, have your authorized servicing
dealer, who has a revolution counter at his disposal, to adjust
your carburettor for optimum operating conditions.
NOTE! If the cutting attachment rotates/moves in the idling
position, turn the idling speed screw counter-clockwise until
the blade stops.
Rec. idling speed: 2700 rpm.
WARNING!
The complete clutch cover with shaft must
Recommended max. speed: See “technical data”.
!
be fitted before the machine is started,
otherwise the clutch can become loose
and cause personal injury.
WARNING!
Contact your servicing dealer, if the idle
speed setting cannot be adjusted so
that the cutting attachment stops. Do
not use the machine until it has been
properly adjusted or repaired.
!
Functioning
• The carburettor governs
the engine speed via the
throttle trigger. In the
carburettor, air/fuel is
mixed. This air/fuel
mixture is adjustable. If
you want to take
Fine adjustment
• When the machine has been ”run-in” the carburettor should
be finely adjusted. The fine adjustment should be carried
out by qualified person. First adjust the L-jet, then the
idling screw T and then the H-jet.
advantage of the
maximum output of the
engine, the setting must be
corret.
Conditions
• Before any adjustments are made the airfilter should be clean
and the airfilter cover fitted. Adjusting the carburettor while
a dirty airfilter is in use will result in a leaner mixture when
the filter is finally cleaned. This can give rise to serious
engine damage.
• The setting of the
carburettor means that the
engine is adjusted to local
conditions, for example
climate, altitude, petrol
and type of two-stroke oil.
• The carburettor has three
adjustment possibilities:
L= Low speed needle
H= High speed
• Carefully turn the L and H needle to the mid point between
fully turned in and fully turned out.
• Do not attempt to adjust the needles beyond the stops as
damage can occur.
• Now start the machine according to the starting instructions
and run it warm for 10 minutes.
NOTE! If the cutting attachment rotates/moves the T screw
should be turned anti-clockwise until the cutting attachment
stops.
adjustment screw
T= Idle speed adjustment
screw
• The fuel quantity required in proportion to the airflow the
throttle trigger level allows is adjusted by means of the L-
and H-needles. Turning the needles clockwise gives a leaner
fuel mixture (less fuel), turning them counter-clockwise gives
a richer fuel mixture (more fuel). A lean mixture gives higher
rpms and a rich one lower rpms.
• The idling speed screw T regulates the position of the
throttle lever in the idling speed position. Turn the idling
speed screw clockwise gives a higher idling speed, turn it
counter-clockwise a lower idling speed.
Low speed needle L
Try to find the highest idling
speed, turning the low speed
needle L clockwise
respectively counter-
clockwise. When the highest
speed has been found, turn
the low speed needle L 1/4
turn counter-clockwise.
+ 1/4
NOTE! If the cutting
attachment rotates/moves in
the idling position, turn the
idling speed screw T
counter-clockwise until the
cutting attachment stops.
L
24– English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Final setting of the idling speed T
Adjust the idling speed with
the screw T, If it is necessary
to readjust. First turn the
idle speed adjusting screw T
clockwise until the cutting
attachment starts to rotate/
move.
Correctly adjusted carburettor
A correctly adjusted carburettor means that the machine
accelerates without hesitation and the machine 4-cycles a
little at max speed. Furthermore, the cutting attachment
must not rotate/move at idling. A too lean adjusted low
speed needle L may cause starting difficulties and bad
acceleration.
A too lean adjusted high speed needle H gives lower power
= less capacity, bad acceleration and/or damage to the
engine.
A too rich adjustment of the two speed needles L and H
gives acceleration problems or too low working speed.
Then turn, counter-
clockwise until the cutting
attachment stops. A correctly
adjusted idle speed setting
occurs when the engine runs
smoothly in every position.
It should also be good
margin to the rpm when the
cutting attachment starts to
rotate/move.
CAUTION! Contact your servicing dealer, if the idle speed
setting cannot be adjusted so that the cutting attachment
stops. Do not use the machine until it has been properly
adjusted or repaired.
High speed needle H
The high speed needle affects
the machine’s power, speed,
temperature and fuel
consumption. A too lean
adjustment on the high
speed needle H (the high
speed needle H is screwed in
too much) gives a too high
speed resulting in engine
damage. Do not allow the
engine to run at full speed
for more than 10 seconds.
Apply full throttle and turn
the high speed needle H
slowly anticlockwise until
the engine runs unevenly.
The high speed needle H is
then turned slowly clockwise
a little until the engine runs
smoothly.
Note the engine should be
run unloaded when
adjusting the high speed
needle. Therefore dismantle
H
the cutting equipment, nut,
support flange and disc drive
before adjusting the high
speed needle. The high speed
needle is adjusted correctly when the machine ‘splatters’ a little
. If the machine smokes heavily at the same time as it ‘splatters’
heavily the adjustment is too rich.
NOTE! For optimum setting of the carburettor, contact a
qualified servicing dealer who has a revolution counter at his
disposal.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Muffler
Cooling system
NOTE!
To maintain as low opera-
ting temperature as possible
the engine is equipped with
a cooling system.
Some mufflers are fitted with a catalytic converter. See
“Technical data” to see whether you clearing saw is fitted with a
catalytic converter.
4
The muffler is designed to
dampen the noise level and
to direct the exhaust fumes
away from the user. The
exhaust fumes are hot and
can contain sparks, which
can result in fire if the
The cooling system consists
of:
1.An air intake on the
starter unit.
2.Cooling fins on the
flywheel.
3.Cooling fins on the
cylinder
3
exhaust fumes are directed
towards a dry and
4.Cylinder cover (leads cold
air onto the cylinder).
inflammable material. Some
mufflers are equipped with a
special spark arrest screen. If
your machine is fitted with
this type of screen it should
be cleaned regularly. This is
done using a wire brush. On
mufflers without a catalytic
converter the screen should
be cleaned weekly, or
2
1
Clean the cooling system
using a brush at least once a
week, in difficult conditions
more often.
A dirty or blocked cooling
system leads to the engine
overheating resulting in
damage to the cylinder and
piston.
replaced if necessary. On
mufflers fitted with a
catalytic converter the
screen should be checked
and cleaned monthly. If the
screen is damaged it should
be replaced. If the screen is
frequently blocked, this can
be a sign that the function
of the catalytic converter is
impaired. Contact your
dealer to inspect the muffler.
A blocked screen will cause
the engine to overheat
resulting in damage to the
cylinder and piston. Also see
under “Maintenance”.
NOTE!
Never use a machine with a
defective muffler.
WARNING!
Mufflers fitted with catalytic converters
become extremely hot during use and
after stopping. This also applies at idling
speeds. Contact can result in burns to
the skin. Be observant to the risk of fire!
!
26– English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Air filter
Spark plug
The air filter should be
cleaned regularly removing
dust and dirt to avoid:
• carburettor malfunction
• starting problems
• reduced engine power
• unnecessary wear to
engine parts
The condition of the spark
plug is affected by:
• An incorrect carburettor
setting.
• An incorrect fuel mixture
(too much or faulty oil).
• A dirty air filter.
0,5 mm
• abnormal fuel
consumption
These factors cause deposits
on the spark plug electrode
that may result in
Clean the filter after every
25 hours or more regularly
if operating conditions are
exceptionally dusty.
malfunction or starting
difficulties.
If the machine is low on power, difficult to start or runs
poorly while idling always check the spark plug first.
If the spark plug is dirty, clean it and at the same time check
that the electrode gap is 0.5 mm. The spark plug should be
changed after about one month of operation or earlier if
necessary.
NOTE! Always use the recommended type of spark plug. An
incorrect spark plug can damage the cylinder/piston.
Cleaning the air filter
Dismantle the air filter cover and remove the air filter. Wash in
clean, warm soapy water. Ensure that the filter is dry before
refitting. An air filter used for a long period of time can never
be cleaned completely. Therefore it is necessary to replace the
filter from time to time with a new filter. A damaged air filter
must always be replaced.
Filing the grass blade
Angle gear
WARNING!
Always stop the engine before starting
!
work on any part of the cutting equipment.
The angle gear is filled
with a sufficient quantity
of grease at the factory.
However, before using the
machine you should check
that the angle gear is filled
to 3/4 with grease. Use
HUSQVARNA special
grease.
This continues to rotate even after the
throttle has been released. Ensure that the
cutting equipment has stopped completely
and remove the cable from the spark plug
before you start to work on it.
• See the cutting
equipment’s packaging
for correct filing
instructions.
Normally, the grease does
not need to be changed
except when the angle gear
is repaired.
• The blades are sharpened
using a single cut flat file.
• Sharpen all edges equally
to maintain the balance
of the blade.
Two-part shaft
The end of the drive axle in
the lower shaft should be
lubricated with grease every
30 hours. There is a risk that
the drive axle ends (splined
coupling) on two-part shafts
jam if they are not lubricated
regularly.
WARNING!
Always discard a blade that is bent,
twisted, cracked, shattered or damaged in
any other way. Never attempt to straighten
a twisted blade for use again. Only use
original blades of the prescribed type.
!
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Sharpening the clearing blade
Maintenance schedule
Below follows some general maintenance instructions.
If you need further information please contact your service
workshop.
WARNING!
Incorrect cutting equipment or an
incorrectly sharpened blade increases
the risk of kickback.
!
Daily maintenance
• See the cutting
equipment’s packaging
for correct filing
instructions.
1
1.Clean the outside of the
machine.
2.Make sure the harness is
not damaged.
• A correctly sharpened
blade is a prerequisite for
working efficiently and to
avoid unnecessary wear to
the blade and clearing
saw.
2
3.Make sure the throttle
trigger lock and the
throttle function correctly
from a safety point of
view.
3
• Make sure that the blade
is well supported when
you use the file. Use a 5.5
mm round file with a file
holder.
4.Check that the stop
switch functions.
4
5.Check that the cutting
head does not rotate while
idling.
• The sharpening angle is
15°. Every other tooth is
sharpened to the right
and the intermediate
5
6.Clean the air filter.
Replace if necessary.
6
7.Check that the guard is
undamaged and not
cracked.
Replace the guard if it
tooth to the left. When
the blade has been heavily
pitted by stones the upper
side of the teeth can, in
exceptional cases, need to
be dressed using a flat file.
In such cases this takes
place before sharpening
with the round file.
has been exposed to
impact or is cracked.
7
8.Check that the blade is
well centred, is sharp, and
is not cracked. An
8
Dressing the top side
must be carried out
equally for all teeth.
uncentred blade causes
9
vibrations that can result
in damage to the
machine.
• Adjust the setting. This
should be 1 mm.
10
9.Check that the trimmer
head is undamaged and
not cracked. Replace the
trimmer head if necessary.
11
10.Check that the locking
nut is tight.
12
11.Check that the blade‘s
transport guard is intact
and that it can be secured
correctly.
12.Check that all nuts and
screws are tightened.
28– English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Weekly
maintenance
Monthly
maintenance
1
1
1.Check the starter, the
starter cord and the return
spring.
1.Clean the fuel tank.
2
2.Clean the carburettor and
the area surrounding it.
2
2.Make sure that the
vibration damping
elements are not damaged.
3.Clean the fan and the area
around it.
3
0,5 mm
3
3.Clean the outside of the
spark plug. Remove and
check the electrode gap.
Adjust the gap to 0.5 mm
or change the spark plug.
4.Check the fuel filter and the
fuel pipe, replace if
necessary.
4
5.Check all cables and
connections.
4
5
4.Clean the cooling fins on
the flywheel.
6.Check the clutch, clutch
springs and the clutch drum
with regard to wear.
5
5.Clean or replace the
muffler’s spark arrest
screen (not on mufflers
with a catalytic converter).
Replace if necessary.
6
6
7.Change the spark plug.
6.Clean the carburettor area.
8.Check and clean the
7
muffler’s spark arrest screen
if necessary (only mufflers
with a catalytic converter).
7.Clean the cooling fins on
the cylinder and check that
the air intake in the starter
unit is not blocked.
7
8
8.Check that the angle gear
is 3/4 filled with grease.
Fill if necessary using
special grease.
8
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
225R/RD
227R/RD
232R/RD
Engine
Cylinder capacity, cm3
Cylinder bore, mm
25,4
34
26,9
35
30,8
35
Stroke length, mm
28
28
32
Idling speed, rpm
2 700
2 700
2 700
Recommended max. speed, rpm
Speed of output axle, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
11 000-11 700
10 000
0,9 kW/9 000 rpm
Yes
Yes
11 000-11 700
10 000
1,0 kW/9 000 rpm
Yes
Yes
11 000-11 700
10 000
1,1 kW/8 400 rpm
Yes
Yes
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, mm
Walbro CD
Champion RCJ 7Y
0,5
Walbro CD
Champion RCJ 7Y
0,5
Walbro CD
Champion RCJ 7Y
0,5
Fuel lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, litres
Walbro WT
0,5
Walbro WT
0,5
Walbro WT
0,5
Weight
Weight without fuel, cutting tool and
guard, kg
6,0 (RD 6,3)
6,0 (RD 6,3)
6,5 (RD 6,7)
Noise levels
Equivalent noise pressure level at the user’s
ear, measured according to EN 11806 and
ISO 7917, dB(A), min/max:
93/99
93/99
90/100
Equivalent noise power level at the user’s
ear, measured according to EN 11806 and
ISO 10884, dB(A), min/max:
106/109
103/109
104/110
Vibration levels
Vibration levels on the handles, measured
according to EN 11806 and ISO 7916,
m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
2,0/2,2
2,2/3,0
1,8/2,1
2,5/3,6
1,6/2,2
1,8/3,0
2,0/3,1
3,1/6,0
2,5/2,5
3,0/3,5
2,0/2,0
5,1/4,9
NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values.
30– English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
235R
Engine
Cylinder capacity, cm3
Cylinder bore, mm
36,3
38
Stroke length, mm
32
Idling speed, rpm
2 700
Recommended max. speed, rpm
Speed of output axle, rpm
Max. engine output, acc. to ISO 8893
Catalytic converter muffler
Speed-regulated ignition system
11 000-11 700
10 000
1,3 kW/9 000 rpm
Yes
Yes
Ignition system
Manufacturer/type of ignition system
Spark plug
Electrode gap, mm
Walbro CD
Champion RCJ 7Y
0,5
Fuel lubrication system
Manufacturer/type of carburettor
Fuel tank capacity, litres
Walbro WT
0,5
Weight
Weight without fuel, cutting tool and
guard, kg
7,3
Noise levels
Equivalent noise pressure level at the user’s
ear, measured according to EN 11806 and
ISO 7917, dB(A), min/max:
92/101
Equivalent noise power level at the user’s
ear, measured according to EN 11806 and
ISO 10884, dB(A), min/max:
105/112
Vibration levels
Vibration levels on the handles, measured
according to EN 11806 and ISO 7916,
m/s
When idling, left/right handles, min:
When idling, left/right handles, max:
At max. speed, left/right handles, min:
At max. speed, left/right handles, max:
2,2/2,7
2,7/4,3
3,5/5,0
4,5/6,2
NOTE!
Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted.
The table indicates the highest and lowest values.
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Approved accessories 225R/RD, 225R/RD Type
Cutting attachment guard Art No.
Centre hole in blades Ø 20 mm
Threaded blade axle M10
Grass blade
Grass 255-4 (∅ 255 4-teeth)
Grass 255-8 (∅ 255 8-teeth)
Multi 255-3 (∅ 255 3-teeth)
503 74 40-01
503 74 40-01
503 74 40-01
Saw blade
Plastic knifes
Trimmer head
Maxi X 200-26 (∅ 200 26-teeth) 503 77 39-01
Tricut ∅ 300
Trimmy H II
Trimmy Hit
Trimmy Hit Pro
Trimmy Fix
Superauto II
Edger attachment ∅ 200
Fixed
503 74 50-01
503 74 50-04
503 74 50-04
503 74 50-04
503 74 50-04
503 74 50-04
-
Edger (RD)
Support cup
-
Approved accessories 232R/RD
Centre hole in blades Ø 20 mm
Threaded blade axle M10
Grass blade
Type
Cutting attachment guard Ref No.
Grass 255-4 ( ∅ 255 4-teeth)
Grass 255-8 ( ∅ 255 8-teeth)
Multi 255-3 ( ∅ 255 3-teeth)
Multi 275-4 ( ∅ 275 4-teeth)
503 74 40-01
503 74 40-01
503 74 40-01
503 74 40-01
Saw blade
Plastic knives
Trimmer head
Maxi X 200-26 (∅ 200 26-teeth) 503 77 39-01
Tricut ∅ 300
Trimmy H II
Trimmy Hit
Trimmy Hit Pro
Trimmy Fix
Superauto II
Edger attachment ∅ 200
Fixed
503 74 40-01
503 74 50-04
503 74 50-04
503 74 50-04
503 74 50-04
503 74 50-04
-
Edger (RD)
Support cup
-
Cutting attachment guard Ref No.
Approved accessories 235R
Centre hole in blades Ø 20 mm
Threaded blade axle M12
Grass blade
Type
502 26 34-01
502 26 34-01
502 26 34-01
502 27 22-01
502 26 34-01, 503 74 50-04
503 74 50-04
503 74 50-04
-
Multi 255-3 (∅ 255 3-teeth)
Multi 275-4 (∅ 275 4-teeth)
Multi 300-3 (∅ 300 3-teeth)
Maxi X 200-26 (∅ 200 26-teeth)
Tricut ∅ 300
Trimmy SII
Trimmy S
Fixed
Saw blade
Plastic knives
Trimmer head
Support cup
-
With bearing
32– English
Download from Www.Somanuals.com. All Manuals Search And Download.
EU declaration of conformity (Only applies to Europe)
(Directive 89/392/EEC, Annex II, A)
We, Husqvarna AB, S-561 82 Huskvarna, Sweden, tel: +46 36-146500, declare under sole responsibility that the
clearing saws Husqvarna 225R/RD/RJ, 227R/RD, 232R/RD and 235R from 1997’s serial numbers and onwards (the
year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following
standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:
-
-
of June 14 1989 “relating to machinery” 89/392/EEC and applicable supplements.
of May 3 1989 “relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.
The following standards have been applied: EN292-2, EN ISO 11806.
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, S-754 50 Uppsala, Sweden, has carried out voluntary type
approval for Husqvarna AB. The certificates are numbered: SEC/94/014 – 225R/RD/RJ, SEC/98/632 – 227R/RD,
SEC/94/022 – 232R/RD/RJ, SEC/94/055 – 235R.
Huskvarna October 21, 1997
Bo Andréasson, Development manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
´*2£|¶6ƨ
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
´*2£|¶6ƨ
Download from Www.Somanuals.com. All Manuals Search And Down1lo9ad9. 8W51
We hope you find the links below useful. For further gardening information visit
Also See
Download from Www.Somanuals.com. All Manuals Search And Download.
|