OPERATOR’S MANUAL
BLOWER/VACUUM
RY08552/RY09905
Your blower/vacuum has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
Never operate the unit without a spark arrestor screen;
this screen is located inside the muffler.
Product users on United States Forest Service land, and
in some states, must comply with fire prevention regu-
lations. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
the federal, state, or local authorities in your area.
Do not allow children or untrained individuals to use this
unit.
Never start or run the engine inside a closed area; breath-
ing exhaust fumes can kill.
Before storing, allow the engine to cool.
WeareyeprotectionwhichismarkedtocomplywithANSI
Z87.1 as well as hearing protection when operating this
equipment.
Use only Ryobi replacement parts and accessories. Fail-
ure to do so may cause poor performance or possible
injury.
Keep all bystanders, children, and pets at least 50 feet
away.
Maintain the unit per maintenance instructions in this
operator’s manual.
Wear heavy long pants, boots, and gloves. Do not wear
loose-fitting clothing, short pants, jewelry of any kind, or
go barefoot.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
SERVICE
To reduce the risk of injury associated with objects being
drawn into rotating parts, do not wear loose clothing,
scarves, neck chains, and the like. Secure long hair so it
is above shoulder level to prevent entanglement in any
rotating parts.
Before cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent starting.
Service on the blower/vacuum must be performed by
qualified repair personnel only. Service or maintenance
performed by unqualified personnel could result in injury
to the user or damage to the product.
Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
Do not operate in poor lighting.
Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
Use only identical replacement parts when servicing the
blower/vacuum. Use of unauthorized parts may create
a risk of serious injury to the user, or damage to the
product.
Wear a face filter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
Check theworkareabeforeeach use. Removeall objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
Always hold the blower in your right hand. Refer to the
OperatiOn instructions later in this manual for additional
information.
REFUELING
Fuel is highly flammable. Take precautions when using
to reduce the chance of serious personal injury.
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
Store fuel in a cool, well-ventilated area, safely away from
spark and/or flame-producing equipment.
To reduce the risk of injury associated with contacting
rotating parts, stop the engine before installing or
removing attachments. Do not operate without guard(s)
in place. Always disconnect the spark plug before
performing maintenance or accessing any movable
parts.
Store fuel in containers specifically designed for this
purpose.
Only refuel outdoors and do not smoke while refueling.
Add fuel before starting the engine. Never remove the cap
of the fuel tank or add fuel while the engine is running or
when the engine is hot.
Do not point the blower nozzle in the direction of people
or pets.
Do not smoke while handling fuel.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or flames.
Never run the unit without the blower tubes installed.
Never place objects inside the blower tubes.
Use only as directed in this operator’s manual.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Do not operate vacuum without vacuum bag installed;
flying debris could cause serious injury. Always close
vacuum bag completely before operating.
Tighten the fuel cap securely after refueling.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
Rotating impeller blades can cause severe injury. Stop
the engine before opening the vacuum door or installing/
changing tubes. Do not put hands or any other object into
the vacuum tubes while they are installed on the unit.
Never attempt to burn off spilled fuel under any circum-
stances.
To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
Neverruntheunitwithouttheproperequipmentattached.
When used as a blower, always install the blower tubes.
When used as a vacuum, always install the vacuum tubes
andvacuumbag.Makesurethevacuumbagiscompletely
zipped when the unit is running to avoid flying debris.
If fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
Avoid situations that could catch the vacuum bag on
fire. Do not operate near an open flame. Do not vacuum
warm ash from fireplaces, barbecue pits, brush piles, etc.
Do not vacuum discarded cigars or cigarettes unless the
cinders are completely cool.
Replace all fuel tank and container caps securely.
Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
Whendrainingthefueltank,useanapprovedfuelstorage
container in a well-ventilated area.
Select bare ground, stop engine, and allow to cool before
refueling.
Savetheseinstructions. Refertothemfrequentlyanduse
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
EXPLANATION
Safety Alert Symbol
Precautions that involve your safety.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read the Operator’s Manual
Wear Eye and Hearing Protection
Vacuum Door
Wear eye protection which is marked to comply with ANSI
Z87.1 as well as hearing protection when operating this
equipment.
Do not run unit while vacuum door is unsecured.
Risk of long hair being drawn into air inlet.
Long Hair
Loose Clothing
Risk of loose clothing being drawn into air intake.
Use unleaded gasoline intended for motor vehicle use with
an octane rating of 87 [(R + M) / ꢀ] or higher. This product is
powered by a ꢀ-cycle engine and requires pre-mixing gasoline
and ꢀ-cycle oil.
Gasoline and Oil
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand com-
pletely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Ryobi customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can re-
sult in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety
glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask
for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is
marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Weight .......................................................................................................................................................................10.4 lbs.
Engine Displacement....................................................................................................................................................ꢀ5.4cc
Air Velocity:
MPH..................................................................................................................................ꢀ05 (with high velocity nozzle)
CFM ..................................................................................................................................................375 (vacuum mode)
Shoulder STrap
cruiSe
conTrol
loWer
Vacuum Tube
Vacuum baG
upper
Vacuum Tube
Vacuum
Tube ScreW
upper handle
ThroTTle TriGGer
choke dial
primer bulb
STarTer Grip
Vacuum handle
Fig. 1a
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
enGine SWiTch
ThroTTle TriGGer
hiGh VelociTY noZZle WiTh
WeT leaf Scraper
cruiSe
conTrol
upper handle
SWeeper noZZle
door Tab
inleT coVer
door
upper bloWer Tube
Fig. 1b
KNOW YOUR BLOWER/VACUUM
ROTOCHOKE™ ZIP START™
The rotochoke zip start allows for easier and quicker
starting.
See Figures 1a - 1b.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
SWEEPER NOZZLE
The sweeper nozzle allows for more area to be covered
during blower operation.
THROTTLE TRIGGER
The blower can be operated at any speed between idle and
full throttle.
BLOWER TUBE AND NOZZLE
The blower tubes can be assembled and installed on the
blower using no tools.
VACUUM/MULCHER
Converting the blower to a vacuum/mulcher can be done
without using tools.
CRUISE CONTROL
The cruise control feature allows the user to operate the
blower without holding the throttle trigger. To slow the engine,
simply push the cruise control lever forward.
VACUUM BAG
The vacuum bag attaches to the blower easily by using the
vacuum bag adaptor.
HIGH VELOCITY NOZZLE WITH WET LEAF
SCRAPER
The high velocity nozzle is great for wet sticky leaves. It
allows you to scrape wet leaves or debris while operating
the blower.
VACUUM HANDLE
This feature allows user to perform vacuuming duties
comfortably.
VACUUM TUBES
The vacuum tubes can be installed on the blower without
using any tools.
MOTOR
The blower has a powerful ꢀ5.4cc engine with sufficient
power to handle tough blowing and vacuuming jobs.
MULCHER
The blower is equipped with a steel mulching blade that
efficiently reduces leaves at a 1ꢀ:1 ratio.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
ASSEMBLING THE BLOWER TUBES
See Figure 2.
Align raised tabs on main housing to the slots on upper
tube; slide together and tighten securely by twisting.
Check tightness after initial run and retighten if needed.
Inspect the product carefully to make sure no breakage
To remove the tubes, rotate the tubes to unlock them and
remove from the blower housing outlet.
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
INSTALLING THE VACUUM HANDLE
See Figure 3.
Lay unit on side as shown.
1-800-860-4050 for assistance.
Insert vacuum handle into the base of unit.
PACKING LIST
Blower
Upper Blower Tube
Sweeper Nozzle
Secure vacuum handle in place using two knobs as
shown.
High Velocity Nozzle
Vacuum Handle
Vacuum Handle Knobs (ꢀ)
Grounding Wire
Upper and Lower Vacuum Tubes
Vacuum Tube Screws (ꢀ)
Vacuum Bag Assembly
Vacuum Bag Adaptor
SWeeper noZZle
ꢀ-Cycle Engine Oil
Operator’s Manual
NOTE: Read and remove all hang tags and store with your
operator’s manual.
upper bloWer
Tube
Fig. ꢀ
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to heed
this warning could result in serious personal injury.
Vacuum
handle
WARNING:
Vacuum
handle
knobS
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
Fig. 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
GROUNDING INSTRUCTIONS
See Figure 4.
INSTALLING THE VACUUM BAG
See Figures 5 - 6.
Remove the nozzle and upper blower tube from the
blower.
After installing the vacuum handle, connect the grounding
wire as shown. This will help prevent static shock when using
the vacuum in low humidity conditions.
Unzip the vacuum bag and place the adaptor inside as
shown.
Align the raised slots on the bag adaptor with the raised
locking tabs on the blower housing outlet; push the bag
adaptor onto the housing. Twist to lock into place.
Rotate the vacuum bag until the shoulder strap is up-
right.
Make sure the vacuum bag is zipped and closed before
starting the unit.
adapTor
Vacuum baG
Fig. 5
adapTor inSTalled
in Vacuum baG
raiSed
SloT
Fig. 4
raiSed
lockinG Tab
Fig. 6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALLING THE VACUUM TUBES
See Figures 7 - 8.
Vacuum
inleT door
WARNING:
Vacuum baG
aSSemblY
Rotating impeller blades can cause severe injury. Always
stop the engine before opening the vacuum door or in-
stalling/changing tubes. Do not put hands or any other
object into the vacuum tubes while they are installed on
the unit.
NOTE: This vacuum/blower is equipped with a vacuum door
interlock. If vacuum door is open and vacuum tubes are not
installed, engine will not start.
door Tab
To install the vacuum tubes:
Secure the upper and lower vacuum tubes together by
aligning the raised locking tabs with the raised slots.
Vacuum
door hinGe
Fig. 7
Tap tube assembly on ground until the screw holes in
lower tube are in the raised slot of the upper tube. Secure
with supplied screws.
Vacuum
inleT door
Vacuum
openinG
Depress door tab and open vacuum inlet door.
Vacuum Tube
aSSemblY
Align tabs on housing with tube assembly. Insert tube
assembly into vacuum opening. Twist clockwise and lock
the upper vacuum tube into the blower housing.
To remove the vacuum tubes:
Twist to loosen the upper vacuum tube by turning coun-
terclockwise.
Remove the vacuum tube assembly from the blower
housing.
Close the vacuum inlet cover door securely.
upper
Vacuum Tube
lockinG Tab
lockinG Tab
Fig. 8
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
NOTE: Premium Exact Mix™ fuel mixture will stay fresh up
to 30 days. DO NOT mix quantities larger than can be used
in a 30 day period.
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
PREMIUM EXACT MIX™ (50:1)
GASOLINE
OIL
WARNING:
1 gallon (US)
1 liter
ꢀ.6 oz.
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
ꢀ0 cc (ꢀ0 ml)
FILLING THE TANK
WARNING:
Always stop the engine before filling the fuel tank.
Never add fuel to a machine with a running or hot
engine. Move at least 30 ft. from the refueling area
before starting engine. Do not smoke while filling the tank.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
Cleanthesurfacearoundthefuelcaptopreventcontami-
APPLICATIONS
You may use this product for the purposes listed below:
nation.
Loosen the fuel cap slowly, by turning it counter-
Clear leaves and other debris from your lawn
clockwise.
Keep decks and driveways free from leaves and pine
Pour the fuel mixture carefully into the tank.
needles
Clean and inspect the fuel cap gasket before replacing
the fuel cap.
WARNING:
Replace the fuel cap and tighten it by turning it clock-
Gasoline is extremely flammable and explosive. A fire or
explosion from gasoline will burn you and others.
wise.
Wipe spilled fuel from the product.
Move at least 30 ft. away from refueling area before
MIXING THE FUEL
starting the product.
This product is powered by a ꢀ-cycle engine and requires
pre-mixing gasoline and ꢀ-cycle oil. The mixture should be
at a 50:1 ratio, using Premium Exact Mix™ ꢀ-cycle engine
oil. If Premium Exact Mix™ ꢀ-cycle engine oil is not available,
use a high quality synthetic ꢀ-cycle engine oil, mixed at a
50:1 ratio. See chart later in this section.
NOTE: It is normal for smoke to be emitted from a new
engine during first use.
WARNING:
Check for fuel leaks. If you find any leaks, correct the
problem before using the product.
To mix the fuel:
Use a clean container that is approved for use with gaso-
line.
WARNING:
A leaking fuel cap is a fire hazard and must be replaced
immediately.
Mix the Premium Exact Mix™ ꢀ-cycle engine oil with
unleaded gasoline in the container, according to the
instructions on the oil package.
NOTE: This engine is certified to operate on unleaded gaso-
line intended for automotive use with an octane rating of 87
[(R + M) / ꢀ] or higher. Do not use automotive oil or ꢀ-cycle
outboard oil.
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING AND STOPPING
enGine SWiTch
ThroTTle
TriGGer
See Figures 9 - 10.
Starting the product differs depending on whether the engine
is cold or warm. Blower should be on a flat, bare surface
for starting.
To start an engine that is cold or has run dry:
choke
leVer
Fill the fuel tank, if necessary. Always use the proper
oil/gasoline mixture. See Mixing the Fuel on page 1ꢀ.
Engage the cruise control lever.
Slowly push the primer bulb seven times.
primer
bulb
Rotate the choke dial clockwise to the FULL CHOKE
position.
Pull the starter grip sharply until engine attempts to run
(no more than 4 pulls).
Rotate the choke dial to the counterclockwise HALF
STarTer
cord
CHOKE position.
Fig. 9
Pull the starter grip sharply until the engine runs.
Allow the engine to run for 10 seconds.
Rotate the choke dial counterclockwise to the RUN posi-
tion.
Engage the throttle trigger to operate.
To start a warm engine:
full
choke
Squeeze the throttle trigger.
half
choke
Rotate the choke dial counterclockwise to the RUN
position.
Slowly press the primer bulb seven (7) times.
run
poSiTion
Pull the starter grip sharply until the engine runs.
To stop the blower/vacuum:
Release the throttle trigger.
Fig. 10
Press and hold the engine switch to the “O” or STOP posi-
proper operaTinG poSiTion
tion.
OPERATING THE BLOWER
See Figures 11 - 12.
WARNING:
Never run the unit without the blower tubes installed or
the vacuum door securely closed. Failure to heed this
warning could result in serious personal injury.
Start the blower. Refer to Starting and Stopping earlier
in this manual. Hold the blower with the upper handle in
your right hand.
WARNING:
Keep away from all hot surfaces of the blower. Failure to
do so could result in possible serious personal injury.
Fig. 11
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
SWeeper noZZle
Operate power equipment at reasonable hours only - not
early in the morning or late at night when people might
be disturbed. Comply with the times listed in local ordi-
nances.
To reduce sound levels, limit the number of pieces of
equipment used at any one time.
hiGh VelociTY
noZZle
Conserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas
such as gutters, screens, patios, grills, porches, and
gardens.
Operate blower at the lowest possible throttle speed to
do the job.
Check your equipment before operation, especially the
muffler, air intakes, and air filters.
Use rakes and brooms to loosen debris before blowing.
Industyconditions, slightlydampensurfaceswhenwater
is available.
Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
Fig. 1ꢀ
ThroTTle TriGGer
Use the full blower nozzle extension so the air stream can
work close to the ground.
cruiSe
conTrol
After using blowers or other equipment, CLEAN UP!
Dispose of debris properly.
Use the sweeper nozzle for the everyday blowing opera-
tion.Thisnozzleallowsformoreareatobecoveredduring
the blowing operation.
The high velocity nozzle is specifically designed for wet
sticky leaves. It allows you to scrape wet leaves or debris
while operating the blower.
CRUISE CONTROL
See Figure 13.
The cruise control can be used to operate the blower without
holding the throttle trigger.
To engage the cruise control:
Pull cruise control lever back towards user, and stop at
the desired throttle setting.
Fig. 13
To release the cruise control, push cruise control lever all
the way towards the front of unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Remove the vacuum tubes and clear the debris from the
VACUUM OPERATION
blower fan housing. Remove the bag and clear the tube.
A small rod or stick may be required to clear the entire
tubelength.Ensurethatalldebrishasbeenclearedbefore
reassembling the vacuum tubes.
See Figure 14.
WARNING:
Never run the unit without the vacuum tubes, vacuum
bag, and vacuum handle installed. Failure to heed this
warning could result in serious personal injury.
proper operaTinG poSiTion
Install the vacuum tubes, vacuum handle, and bag. Refer
to the aSSembly section earlier in this manual.
Start the blower. Refer to Starting and Stopping earlier
in this manual.
Place the vacuum bag strap over your right shoulder.
Hold the upper handle in your left hand and the vacuum
handle in your right hand.
Move the blower/vacuum from side to side along outer
edge of the debris. To avoid clogging, do not place the
vacuum tube directly into the debris pile.
Hold the engine higher than the inlet end of the vacuum
tube.
Always point vacuum tube downhill when working on a
hillside.
To avoid injury to the operator or unit, do not pick up
rocks, broken glass, bottles, or other similar objects.
If the vacuum tubes should clog, stop the engine and
disconnect the spark plug wire before cleaning out the
obstruction.
Fig. 14
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
WARNING:
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a an Authorized Service Center.
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEANING THE AIR FILTER SCREEN
See Figure 15 - 16.
For proper performance and long life, keep the air filter
screen clean.
choke dial
coVer
Remove the hex nut, wavy washer, flat washer, and choke
dial cover.
Brush the air filter screen lightly to clean.
WaVY
WaSher
Reinstall the choke dial cover, flat washer, wavy washer,
and hex nut.
SPARK ARRESTOR
The muffler is equipped with a spark arrestor screen inside
muffler body. After extended use the screen can become
dirty, and you may need to have the screen replaced by an
authorized servicing dealer.
flaT
heX
nuT
WaSher
filTer
Screen
Fig. 15
WARNING:
To avoid a fire hazard, never run the blower without the
spark arrestor in place.
CLEANING THE EXHAUST PORT AND MUFFLER
Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port,
muffler, and/or spark arrestor screen may become blocked
with carbon deposits. If you notice a power loss with your
gas powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
bruSh
VACUUM BAG
filTer
Screen
A dirty bag will reduce performance. To clean the bag, turn it
inside out and shake. Wash the bag in soapy water at least
once a year. To obtain a replacement bag, see How to Order
Replacement Parts on the back page of this manual.
Fig. 16
FUEL CAP
STORING THE PRODUCT
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine per-
formance. If performance improves when the fuel cap is
loosened, the check valve may be faulty or filter clogged.
Replace the fuel cap if required.
Clean all foreign material from the product. Store it in a
well-ventilatedplacethatisinaccessibletochildren.Keep
away from corrosive agents such as garden chemicals
and de-icing salts.
Abide by all Federal and local regulations for the safe
storage and handling of gasoline.
WARNING:
WHEN STORING 1 MONTH OR LONGER:
A leaking fuel cap is a fire hazard and must be replaced
immediately.
Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
SPARK PLUG
This engine uses a Champion RCJ6Y with 0.63 mm
(0.0ꢀ5 in.) electrode gap. Use an exact replacement spark
plug and replace annually.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORIZED SERVICING DEALER.
PROBLEM
Engine fails to start
CAUSE
REMEDY
No fuel in tank
Fill tank.
Spark plug shorted or fouled
Replace spark plug.
Replace spark plug.
Spark plug is broken (cracked
porcelain or electrodes broken)
Ignition lead wire shorted, broken, or Replace lead wire or attach to spark
disconnected from spark plug
plug.
Ignition inoperative
Contact authorized service center.
Engine hard to start
Water in gasoline or stale fuel mixture Drain entire system and refill with fresh
fuel.
Too much oil in fuel mixture
Engine is under or over choked
Weak spark at spark plug
Air filter clogged
Drain and refill with correct mixture.
Adjust choke as necessary.
Contact authorized service center.
Engine lacks power
Engine overheats
Clean air filter. Refer to Cleaning the
Air Filter Screen earlier in this manual.
Insufficient oil in fuel mixture
Mix fuel as described in starting
instructions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTY STATEMENT
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
Techtronic Industries North America, Inc., warrants to the
original retail purchaser that this RYOBI® brand outdoor
product is free from defect in material and workmanship
and agrees to repair or replace, at Techtronic Industries
North America, Inc.’s, discretion, any defective product
free of charge within these time periods from the date of
purchase.
B. Wear items – Bump Knobs, Outer Spools, Cutting
Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts,Tines,FeltWashers,HitchPins,MulchingBlades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bag
and Straps, Guide Bars, Saw Chains
Techtronic Industries North America, Inc., reserves the
right to change or improve the design of any RYOBI® brand
outdoorproductwithoutassuminganyobligationtomodify
any product previously manufactured.
Two years if the product is used for personal, family or
household use;
90 days, if used for any other purpose, such as
commercial or rental.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-
DAY WARRANTY PERIOD. TECHTRONIC INDUSTRIES
NORTH AMERICA, INC.’S, OBLIGATION UNDER THIS
WARRANTYISSTRICTLYANDEXCLUSIVELYLIMITEDTO
THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS
AND TECHTRONIC INDUSTRIES NORTH AMERICA,
INC., DOES NOT ASSUME OR AUTHORIZE ANYONE
TO ASSUME FOR THEM ANY OTHER OBLIGATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. TECHTRONIC
INDUSTRIES NORTH AMERICA, INC., ASSUMES NO
RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,
OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED
TO, EXPENSE OF RETURNING THE PRODUCT TO AN
AUTHORIZED RYOBI SERVICE CENTER AND EXPENSE
OFDELIVERINGITBACKTOTHEOWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.
Any part of this product found in the reasonable judgment
ofTechtronicIndustriesNorthAmerica, Inc. tobedefective
in material or workmanship will be repaired or replaced
withoutchargeforpartsandlaborbyanauthorizedservice
center for RYOBI® brand outdoor products (Authorized
Ryobi Service Center).
Theproduct,includinganydefectivepart,mustbereturned
to an authorized Ryobi service center within the warranty
period.Theexpenseofdeliveringtheproducttotheservice
center for warranty work and the expense of returning it
back to the owner after repair or replacement will be paid
by the owner. Techtronic Industries North America, Inc.’s,
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach of
warrantyshallbecauseforcancellationorrescissionofthe
contractofsaleofanyRYOBI® brandoutdoorproduct.Proof
of purchase will be required by the dealer to substantiate
any warranty claim. All warranty work must be performed
by an authorized service dealer.
This warranty is limited to ninety (90) days from the date
of original retail purchase for any RYOBI® brand outdoor
product that is used for rental or commercial purposes, or
any other income-producing purpose.
This warranty does not cover any product that has been
subject to misuse, neglect, negligence, or accident, or that
has been operated in any way contrary to the operating
instructions as specified in this operator’s manual. This
warranty does not apply to any damage to the product that
is the result of improper maintenance or to any product
that has been altered or modified. The warranty does not
extendtorepairsmadenecessarybynormalwearorbythe
use of parts or accessories which are either incompatible
withtheRYOBI® brandoutdoorproductoradverselyaffect
its operation, performance, or durability. In addition, this
warranty does not cover:
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
ThiswarrantyappliestoallRYOBI® brandoutdoorproducts
manufacturedbyorforTechtronicIndustriesNorthAmerica,
Inc., and sold in the United States and Canada.
To locate your nearest Authorized Ryobi Service Center,
dial 1-800-860-4050.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUM-
BERS REqUIRED TO MEET THE CARB REqUIREMENTS.
TECHTRONIC INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL
AND CALIFORNIA EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board
(CARB), and Techtronic Industries North America, Inc., are pleased to explain the
Emissions Control System Warranty on your ꢀ007 model year non-road or small off-
road engine. In California, new equipment that uses small off-road engines must be
designed, built, and equipped to meet the state’s stringent anti-smog standards. In
other states, new ꢀ000 and later model year non-road engines must be designed,
built, and equipped at the time of sale to meet the U.S. EPA regulations for small
non-road engines. The non-road engine must be free from defects in materials and
workmanship which cause it to fail to conform with U.S. EPA standards for the first
two years of engine use from the date of sale to the ultimate purchaser. Techtronic
Industries North America, Inc., must warrant the emission control system on your
non-road or small off-road engine for the period of time listed above provided there
has been no abuse, neglect, or improper maintenance of your non-road or small
off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection
system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps,
connectors, and other associated components. Also included may be hoses, belts
and connectors, and other emission-related assemblies.
Where a warrantable condition exists, Techtronic Industries North America, Inc., will
repair your non-road or small off-road engine at no cost to you, including diagno-
sis, parts, and labor performed at an authorized service center for RYOBI® brand
outdoor products.
Techtronic Industries North America, Inc., shall remedy warranty defects at any
authorized RYOBI® Authorized Service Center, including any distribution center
that may be franchised to service the subject engines. Any diagnostic work done
at a RYOBI® Authorized Service Center shall be free of charge to the owner if such
work determines that a warranted part is defective. Any manufacturer-approved or
equivalent replacement part may be used for any warranty maintenance or repairs
on emission-related parts, and must be provided free of charge to the owner if the
part is still under warranty. Techtronic Industries North America, Inc., is liable for
damages to other engine components caused by the failure of a warranted part
still under warranty.
Add-on or modified parts that are not exempted by the California Air Resource Board
may not be used. The use of any non-exempted add-on or modified parts will be
grounds for disallowing a warranty claim. Techtronic Industries North America, Inc.,
will not be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
The California Air Resources Board’s Emission Warranty Parts List specifically defines
the emission-related warranted parts. (EPA’s regulations do not include a parts list,
but the EPA considers emission-related warranted parts to include all the parts listed
below.) Techtronic Industries North America, Inc., will provide any documents that
describe its warranty procedures or policies within five days upon request by the
California Air Resources Board.
EMISSIONS PARTS LIST
Emissions parts vary from product to product. Your emissions control system warranty
applies to any of the following components that may be included on your product:
MANUFACTURER’S WARRANTY COVERAGE:
This product’s emissions control system is warranted for two years. If any emis-
sion-related part on your engine is defective, the part will be repaired or replaced by
Techtronic Industries North America, Inc., free of charge.
(1) Fuel Metering System
(i) Carburetor and internal parts (and/or pressure regulator or fuel injection
system).
OWNER’S WARRANTY RESPONSIBILITIES
(a) As the non-road or small off-road engine owner, you are responsible for
the performance of the required maintenance listed in your operator’s manual.
Techtronic Industries North America, Inc., recommends that you retain all re-
ceipts covering maintenance on your non-road or small off-road engine, but
Techtronic Industries North America, Inc., cannot deny warranty solely for the
lack of receipts or for your failure to ensure the performance of all scheduled
maintenance. Any replacement part or service that is equivalent in performance
and durability may be used in non-warranty maintenance or repairs, and shall
not reduce the warranty obligations of Techtronic Industries North America, Inc.
(ii) Air/fuel ratio feedback and control system.
(iii) Cold start enrichment system.
(iv) Fuel Tank.
(ꢀ) Air Induction System
(i) Controlled hot air intake system.
(ii) Intake manifold.
(iii) Air filter.
(3) Ignition System
(b) As the non-road or small off-road engine owner, you should be aware, however,
that Techtronic Industries North America, Inc., may deny you warranty coverage if
your non-road or small off-road engine or a part has failed due to abuse, neglect,
improper maintenance, or unapproved modifications.
(c) You are responsible for presenting your non-road or small off-road engine to an
authorized service dealer as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you
should contact a Techtronic Industries North America, Inc., Customer Representa-
tive at 1-800-860-4050.
(i) Spark Plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system.
(4) Exhaust Gas Recirculation (EGR) System
(i) EGR valve body and carburetor spacer, if applicable.
(ii) EGR rate feedback and control system.
(5) Air Injection System
(i) Air pump or pulse valve.
(ii) Valves affecting distribution of flow.
(iii) Distribution manifold.
DEFECT WARRANTY COVERAGE REqUIREMENTS:
(a) The warranty period begins on the date the engine or equipment is delivered to
an ultimate purchaser.
(6) Catalyst or Thermal Reactor System
(i) Catalytic converter.
(b) General Emissions Warranty Coverage. Techtronic Industries North America,
Inc., warrants to the ultimate purchaser and each subsequent purchaser that your
non-road or small off-road engine is designed, built, and equipped at the time of sale
to conform with all applicable regulations adopted by the California Air Resources
Board or the United States Environmental Protection Agency; and that it is free from
defects in materials and workmanship which cause the engine to fail to conform with
applicable regulations for a period of two years from the date the non-road or small
off-road engine is purchased by the initial purchaser.
(ii) Thermal reactor.
(iii) Exhaust manifold.
(7) Particulate Controls
(i) Traps, filters, precipitators, and any other device used to capture particulate
emissions.
(8) Miscellaneous Items Used in Above Systems
(i) Electronic controls.
(c) The warranty on emissions-related parts will be interpreted as follows: Any
warranted part that is not scheduled for replacement as required in the Emissions
Maintenance Schedule and Warranty Parts List set forth below is warranted for two
years. If any such part (including any part that is scheduled only for regular inspection)
fails during the period of warranty coverage, it will be repaired or replaced at any
RYOBI® Authorized Service Center at no charge. Any such part repaired or replaced
under warranty will be warranted for the remaining warranty period. A statement to
the effect of “repair or replace as necessary” would not reduce the period of war-
ranty coverage. Any warranted part that is scheduled for replacement as required
maintenance in the Emissions Maintenance Schedule and Warranty Parts List is
warranted for the period of time prior to the first scheduled replacement point for
that part. Any such part repaired or replaced under warranty is warranted for the
remainder of the period prior to the first scheduled replacement point, and will be
repaired or replaced at any RYOBI® Authorized Service Center for no charge until
that replacement point is reached.
(ii) Vacuum, temperature, and time sensitive valves and switches.
(iii) Hoses, belts, connectors, and assemblies.
Techtronic Industries North America, Inc., will furnish with each new engine written
instructions for its maintenance and use by the owner.
The Emissions Compliance Period referred to on the Emissions Compliance label
indicates the number of operating hours for which the engine has been shown to
meet Federal emission requirements. Category C=50 hours, B=1ꢀ5 hours, and
A=300 hours.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts
Inspect Before
Each Use
Clean Every
5 Hours
Replace
Every 25 Hours
or Yearly
Clean Every
25 Hours
or Yearly
Replace Every
50 Hours
CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X
AIR FILTER ASSY
includes:
Filter ................................................................. X
SPARK SCREEN ..................................................................................................................X
CARBURETOR ASSY
includes:
Heat Dam
Gaskets
FUEL TANK ASSY
includes:
Fuel Lines........................ X
Fuel Cap.......................... X
Fuel Filter
IGNITION ASSY
includes:
Spark Plug........................................................................................ X
ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
make The moST of Your purchaSe!
Your product has been fully tested prior to shipment
to ensure your complete satisfaction.
For any questions about operating or maintaining
your product, call the Ryobi Help Line!
To register your Ryobi product or set up your eBox™ account by regular mail, please print the following in-
formation on a 3 in. x 5 in. card or standard postcard: your name, mailing address, phone numbers, email
address, Ryobi product(s) purchased with item number from package, and serial number for each product.
Mail the card to: Techtronic Industries North America, Inc., Attn. Ryobi Registration, 14ꢀ8 Pearman Dairy
Road, Anderson, SC ꢀ96ꢀ5.To receive information on our company and products, please include the following
statement on your registration card: “Send me information on your products and company using the contact
information I am providing with this product registration.”
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
BLOWER/VACUUM
RY08552/RY09905
WARNING:
The engine exhaust from this product contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
CALIFORNIA PROPOSITION 65
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
RY0855ꢀ/RY09905
• MODEL NUMBER
• SERIAL NUMBER
• HOW TO OBTAIN REPLACEMENT PARTS:
1-800-860-4050. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
1-800-860-4050.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-860-4050.
RYOBI® is a registered trademark of Ryobi Limited used under license.
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
14ꢀ8 Pearman Dairy Road
Anderson, SC ꢀ96ꢀ5
Phone 1-800-860-4050
987000-1ꢀ6
7-3-07 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|