Owner’s Manual
Thank you, and congratulations on your choice of the Roland Digital Piano RD-300SX.
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (p. 2; p. 4). These sections provide important information
concerning the proper operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new unit, Owner’s Manual
should be read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
202
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Download from Www.Somanuals.com. All Manuals Search And Download.
012b
101b
•
Immediately turn the power off, remove the AC
•
The unit and the AC adaptor should be located so
adaptor from the outlet, and request servicing by
your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on
the “Information” page when:
their location or position does not interfere with
their proper ventilation.
..........................................................................................................
101cThis (RD-300SX) for use only with Roland stand
KS-12. Use with other stands (or carts) is capable
of resulting in instability causing possible injury.
..........................................................................................................
102cAlways grasp only the plug on the AC adaptor
•
• The AC adaptor, the power-supply cord, or the
plug has been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
•
cord when plugging into, or unplugging from, an
outlet or this unit.
• The unit has been exposed to rain (or otherwise
has become wet); or
..........................................................................................................
103b
• The unit does not appear to operate normally
or exhibits a marked change in performance.
..........................................................................................................
013 In households with small children, an adult
•
At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor insulation
and lead to fire.
•
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014 Protect the unit from strong impact.
•
..........................................................................................................
104 Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106 Never climb on top of, nor place heavy objects on
(Do not drop it!)
•
..........................................................................................................
015 Do not force the unit’s power-supply cord to
•
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
•
the unit.
..........................................................................................................
107cNever handle the AC adaptor or its plugs with
•
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
016 Before using the unit in a foreign country, consult
108b
•
•
Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
..........................................................................................................
023 DO NOT play a CD-ROM disc on a conventional
109b
•
Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet (p. 11, p.
13).
•
audio CD player. The resulting sound may be of a
level that could cause permanent hearing loss.
Damage to speakers or other system components
may result.
..........................................................................................................
110b
•
Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
..........................................................................................................
..........................................................................................................
118a
•
Should you remove ground terminal screw, keep
them in a safe place out of children’s reach, so
there is no chance of them being swallowed
accidentally.
..........................................................................................................
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following:
Power Supply
Repairs and Data
301
452
• Do not connect this unit to same electrical outlet that is
• Please be aware that all data contained in the unit’s
being used by an electrical appliance that is controlled by an
inverter (such as a refrigerator, washing machine,
memory may be lost when the unit is sent for repairs.
Important data should always be backed up in another
MIDI device (e.g., a sequencer), or written down on paper
(when possible). During repairs, due care is taken to avoid
the loss of data. However, in certain cases (such as when
circuitry related to memory itself is out of order), we
regret that it may not be possible to restore the data, and
Roland assumes no liability concerning such loss of data.
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a power
supply noise filter between this unit and the electrical outlet.
302
• The AC adaptor will begin to generate heat after long
hours of consecutive use. This is normal, and is not a
cause for concern.
Additional Precautions
551
307
• Please be aware that the contents of memory can be
• Before connecting this unit to other devices, turn off the
irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against
the risk of loosing important data, we recommend that
you periodically save a backup copy of important data
you have stored in the unit’s memory in another MIDI
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Placement
351
device (e.g., a sequencer).
• Using the unit near power amplifiers (or other equipment
552
• Unfortunately, it may be impossible to restore the contents
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit;
or move it farther away from the source of interference.
of data that was stored in another MIDI device (e.g., a
sequencer) once it has been lost. Roland Corporation
assumes no liability concerning such loss of data.
352a
• This device may interfere with radio and television reception.
553
• Use a reasonable amount of care when using the unit’s
Do not use this device in the vicinity of such receivers.
352b
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initi-
ating a call, or while conversing.
Should you experience such problems, you should
relocate such wireless devices so they are at a greater
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
558a
distance from this unit, or switch them off.
• To avoid disturbing your neighbors, try to keep the unit’s
354a
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
559a
Excessive heat can deform or discolor the unit.
• When you need to transport the unit, package it in the box
355b
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
561
• Use only the specified expression pedal (EV-5, EV-7; sold
separately). By connecting any other expression pedals,
you risk causing malfunction and/or damage to the unit.
has completely evaporated.
358
Handling CD-ROMs
• Do not allow objects to remain on top of the keyboard.
801
This can be the cause of malfunction, such as keys ceasing
to produce sound.
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean
using a commercially available CD cleaner.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind,
to avoid the possibility of discoloration and/or deformation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel.................................................................................................................................................. 10
Adjusting the Volume.............................................................................................................................. 14
Basic Operation of the RD-300SX........................................................................................................... 16
Performing with Two Layered Tones ([DUAL])...................................................................... 21
Changing the Velocity When the Key Touch Is Set to “Fixed”.............................................. 26
Changing the Reverb Effect Type............................................................................................... 27
Changing the Depth of Reverb Effect (Reverb Depth) ............................................................ 27
Changing the Depth of Effect...................................................................................................... 28
Playing Rhythm ([RHYTHM]) ............................................................................................................... 32
Changing the Rhythm Pattern .................................................................................................... 32
Changing Rhythm Tempos.......................................................................................................... 33
Changing the Rhythm Volume ................................................................................................... 33
Selecting Stored Settings ([SETUP])....................................................................................................... 34
Storing Settings to Setups ([WRITE]) .................................................................................................... 35
Disabling the Buttons (Panel Lock)........................................................................................................ 36
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Parameters That Can Be Set.................................................................................................................... 37
Making System Settings (System).......................................................................................................... 37
Tuning to Other Instruments’ Pitches (Master Tuning).......................................................... 38
Adjusting the Tuning (Temperament, Key).............................................................................. 38
Using the Pedal to Switch Setup (Setup Pedal Shift)............................................................... 39
Changing the Pedal Function (Control Pedal Function)......................................................... 40
Setting the Pan............................................................................................................................... 43
Part On/Off (Part).................................................................................................................................... 43
Transferring Setups to External Devices (Setup Bulk Dump)................................................ 44
Selecting Sounds on an External MIDI Device ......................................................................... 47
Recording the Performance ......................................................................................................... 48
Switching Setups........................................................................................................................... 49
Connecting to Your Computer via USB (USB Mode).........................50
Switching USB Drivers ............................................................................................................................ 50
Exchanging MIDI Messages with Your Computer ............................................................................. 50
About V-LINK.........................................................................................51
How to Use the V-LINK............................................................................................................... 51
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Error Messages.....................................................................................59
Tone List................................................................................................60
Shortcut List..........................................................................................66
MIDI Implementation Chart ..................................................................67
Main Specifications ..............................................................................68
Index.......................................................................................................69
220
*
All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Features
Refined Design and a Compact,
Lightweight Body
The RD-300SX’s black alumite body not only looks great on
stage, it’s also compact and lightweight, for an instrument
that is easy to carry wherever you are performing.
High-Quality Effects
The RD-300SX also includes 78 types of multi-effects, for
example sympathetic resonance that simulates the resonance
of the piano strings when the pedal is pressed, a rotary
speaker effect, distortion, and more. The instrument also
provides a wide variety of tone adjustment capabilities
including a two-band digital equalizer and a Sound Control
function that helps check inconsistencies in the sound.
88-Key Multi-Sampled Piano
Those same piano sounds, created through 88-key sampling,
which won wide acclaim when they made their debut in the
Fantom-X series of instruments (the ultimate in synthesizers),
are provided onboard the RD-300SX. The only difference is
that they have been arranged so they more aptly suit their
new role as the sounds produced by a dedicated stage piano.
This gives you the kind of expressiveness available only with
88-key multisampled sounds, expressive power unequalled
by any other synthesizer.
A Variety of Functions Available
Only with a Stage Piano
This instrument features not only the standard controls you
would expect on a stage piano, such as the bender/
modulation lever, it also includes a [SETUP] button that
allows you to call up a variety of stored settings instantly and
a [MIDI TX] button that gives you simplified control of
external sound modules.
Additionally, you can take the piano wave forms that make
your band sound great and store them in the instrument, and
use two types of piano sounds to enjoy performances in a
variety of genres.
This stage piano provides rapid, intuitive control of your
sounds.
This instrument also features a full line of important stage
piano tones including electric piano, organ, strings, synth
pad, and more.
Rhythm Function
You can play rhythm patterns with the touch of a single
button. This enables you to back up your performances with
realistic drum sounds, improvise with a true jam session feel,
and use the metronome to practice grooves you are not yet
familiar with.
A Full 128 Voices
The RD-300SX features 128-voice polyphony, with all sounds
available in every performance mode. Enjoy natural
performances even when layering multiple sounds.
USB and GM/GM2 Compatible
The RD-300SX comes equipped with a USB port and GM2
sound module that can be utilized when you use the RD-
300SX as an input keyboard in composing songs with a
computer or when using the instrument as a sound module.
Compact Hammer Action Keyboard
and Half-Pedal Capability
The RD-300SX incorporates a hammer action keyboard using
absolutely no springs, which is even capable of reproducing
the subtle changes in touch that are normally experienced
when you move from the lower to the higher registers.
Additionally, a half-pedal capable pedal (DP-8) is also
included, enabling authentic pedal performance.
*
Only MIDI messages are handled with the USB function.
Convention Used in This Manual
• Words enclosed in square brackets [ ] indicate panel
buttons.
You can access Split and Dual modes and carry out other
main operations simply by pressing a single button (p. 20).
Furthermore, pressing the ONE TOUCH [PIANO] button lets
you immediately switch to the settings most suited for piano
performances, regardless of the mode or settings currently in
effect (p. 18).
Example: [SPLIT] indicates the SPLIT button.
• (p. **) indicates a reference page.
985
• The explanations in this manual include illustrations that
depict what should typically be shown by the display.
Note, however, that your unit may incorporate a newer,
enhanced version of the system (e.g., includes newer
sounds), so what you actually see in the display may not
always match what appears in the manual.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Descriptions
Front Panel
fig.00b-01
2
6
13
14
16
15
7 8
11
12
1
3 4 5
9 10
17
1. VOLUME slider
13. ONE TOUCH
Adjusts the overall volume that is output from the rear panel
OUTPUT jacks and PHONES jack (p. 14).
[PIANO]
[SETUP]
2. EQUALIZER/EFFECTS
[LOW] knob
Calls up the stored settings (Setup) (p. 34).
Adjusts the sound’s low-frequency range.
[HIGH] knob
14. MODE
[DUAL]
Adjusts the sound’s high-frequency range.
Switches the RD-300SX to “Dual Mode,” which enables
[SPLIT]
3. [SOUND CONTROL/V-LINK]
[SOUND CONTROL] switches SOUND CONTROL on/off (p. 30).
[V-LINK] switches the V-LINK function on/off (p. 51).
Puts the keyboard in “Split mode,” wherein you can use more
than one tone by having different tones play in different parts of
the keyboard (p. 22).
4. [REVERB]
Switches REVERB on/off (p. 27).
15. [LOWER SELECT/KEY TOUCH]
When this is switched to on, you can select the LOWER ZONE
tone with the TONE SELECT buttons (p. 24). This button is also
5. [MULTI EFFECTS]
Switches the multi-effects on/off (p. 28).
6. ZONE LEVEL sliders
16. FUNCTION
Adjusts the volume level in each zone (p. 24).
[EDIT]
7. [MIDI TX]
Press this button when you wish to adjust various settings (p. 37).
In addition, you can listen to the demo songs by simultaneously
pressing this button and [WRITE] (DEMO PLAY) (p. 17).
[WRITE]
Enables control of external MIDI sound modules from the RD-
300SX (p. 46, p. 47, p. 48).
8. [RHYTHM/TEMPO]
Stores the current settings to “Setup” (p. 35).
[RHYTHM] is used to turn the rhythm performance on and off (p. 32).
[TEMPO] is used to change the rhythm tempo (p. 33).
17. TONE SELECT buttons
Pressed to select a tone’s category (p. 19).
9. [SHIFT/EXIT]
[SHIFT] is pressed simultaneously with other buttons to execute
various functions.
[EXIT] is pressed to return to previous screens.
Pitch Bend/Modulation lever
fig.00b-02
10. [TRANSPOSE/ENTER]
[TRANSPOSE] sets the range of the keyboard to transposed (p. 25).
[ENTER] is used to finalize a value or execute an operation.
11. DISPLAY
This shows the Tone numbers and the values of various
settings, etc.
This allows you to control pitch bend or apply vibrato (p. 30).
12. [DEC], [INC]
This is used to modify values.
If you keep on holding down one button while pressing the
other, the value change accelerates.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Descriptions
Rear Panel
fig.00b-03
3
1
2
4 5
6 7 8 9
1. USB connector
6. Ground terminal
This connector lets you use a USB cable to connect your
computer to the RD-300SX (p. 50).
927
Depending on the circumstances of a particular setup, you may
experience a discomforting sensation, or perceive that the
surface feels gritty to the touch when you touch this device,
microphones connected to it, or the metal portions of other
objects, such as guitars. This is due to an infinitesimal electrical
charge, which is absolutely harmless. However, if you are
concerned about this, connect the ground terminal (p. 11) with
an external ground. When the unit is grounded, a slight hum
may occur, depending on the particulars of your installation. If
you are unsure of the connection method, contact the nearest
Roland Service Center, or an authorized Roland distributor, as
listed on the “Information” page.
2. PEDAL jacks (DAMPER, CONTROL)
Connecting the pedal switch (DP series) provided with the RD-
damper pedal.
With an optional expression pedal (such as the EV series or
other model) connected to the CONTROL jack, you can then
assign a variety of functions to the pedal (p. 39, p. 40).
3. MIDI connectors (IN, OUT)
Used for connecting external MIDI devices and for transmission
of MIDI messages (p. 12, p. 47).
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
4. OUTPUT L(MONO)/R jacks
Provide output of the audio signals. These are connected to an
amp or other device. For monaural output use the L/MONO
jack (p. 12).
• Telephone-line ground or lightning rod (may be
dangerous in the event of lightning)
7. [POWER]
Turns the power on/off (p. 13).
5. PHONES jack
A set of headphones can be connected to this jack (p. 12).
Even when headphones are connected, sound will still be
output from the output jacks.
8. DC In jack
Connect the included AC adaptor here (p. 11).
9. Cord hook
Anchor the included power cord here (p. 11).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Making Connections
1
Before you begin making connections, confirm the following.
Is the volume level of the RD-300SX turned all the way down?
Is the power to the RD-300SX turned off?
2
Connect the supplied power cord to the supplied AC adaptor.
fig.00c-01
AC adaptor
Power cord
Power outlet
3
4
Connect the supplied AC adaptor to the RD-300SX, and then plug its other
end into a power outlet.
Loop the AC adaptor cord around the cord hook to fasten it in place.
fig.00c-02
Rear Panel
ground terminal
cord hook
The cord of the
supplied AC Adaptor
To the Power Outlet
924
927
* To prevent the inadvertent disruption of power to your unit (should the plug be pulled out
accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power
cord using the cord hook, as shown in the illustration.
* Depending on the circumstances of a particular setup, you may experience a discomforting
sensation, or perceive that the surface feels gritty to the touch when you touch this device,
microphones connected to it, or the metal portions of other objects, such as guitars. This is
due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are
concerned about this, connect the ground terminal (see figure) with an external ground.
When the unit is grounded, a slight hum may occur, depending on the particulars of your
installation. If you are unsure of the connection method, contact the nearest Roland Service
Center, or an authorized Roland distributor, as listed on the “Information” page.
Unsuitable places for connection
• Water pipes (may result in shock or electrocution)
• Gas pipes (may result in fire or explosion)
• Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Connecting the RD-300SX to External Equipment
The RD-300SX is not equipped with an amplifier or speakers. In order to produce
sound, you need to hook up audio equipment such as a monitor speaker or a stereo
set, or use headphones.
To prevent malfunction and/
* Audio cables, MIDI cables, USB cables, headphones, and expression pedals are not included.
or damage to speakers or other
devices, always turn down the
volume, and turn off the
power on all devices before
making any connections.
921
Consult your Roland dealer if you need to purchase accessories such as these.
fig.00c-03
Stereo
headphones
MIDI IN
MIDI OUT
MIDI sound module etc.
Roland
MIDI sequencer etc.
Use Stereo headphones.
Expression pedal (EV-5, 7)
or Pedal switch (DP Series)
Use only the specified
expression pedal (EV-5, EV-7;
sold separately). By connecting
any other expression pedals,
you risk causing malfunction
and/or damage to the unit.
925
Monitor speakers
(powered)
Mixer etc.
Pedal switch
(DP series)
Power amp.
1
Before you begin making connections, confirm the following.
Set the switch on the included
pedal to “Continuous” when
the pedal is connected.
Is the volume level of the RD-300SX or connected amp turned all the way down?
Connecting Pedals
Connect the pedal included with the RD-300SX to one of the PEDAL jacks.
When connected to the DAMPER jack, the pedal can be used as a damper pedal.
Connecting the pedal to the CONTROL jack allows you to assign a variety of
functions to the pedal (p. 40).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Turning the Power On and Off
941
Once the connections have been completed, turn on power to your various devices
in the order specified. By turning on devices in the wrong order, you risk causing
malfunction and/or damage to speakers and other devices.
Turning On the Power
1
Before you switch on the power, turn the volume down all the way using the
VOLUME slider.
To prevent incorrect
functioning of the Pitch Bend
Lever (p. 30), refrain from
touching the lever when you
turn on the power.
Also completely turn down the volume of any connected audio device and other
equipment.
fig.00c-05
This unit is equipped with a
protection circuit. A brief
interval (a few seconds) after
power up is required before
the unit will operate normally.
942
2
Press the [POWER] switch on the back of the unit.
The power will turn on, and “Pno” appears in the display.
fig.00c-06
Rear Panel
Lower Position
ON
3
Turn on the power to connected external devices.
4
Adjust the volume of the connected external device.
5
Adjust the RD-300SX’s volume to obtain the proper volume level.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Turning Off the Power
1
Before you turn off the power, turn the volume down all the way using the
VOLUME slider.
Also completely turn down the volume of any connected audio device and other
equipment.
2
Turn off the power to connected external devices.
3
Press the [Power] switch on the back of the unit.
The power is switched off.
fig.00c-07
Rear Panel
Upper Position
OFF
Adjusting the Volume
fig.00c-05
1
Adjust the volume using the VOLUME slider.
Move the slider up to increase the volume, or down to lower it.
Also adjust the volume of the connected device to an appropriate level.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Ready
Tuning to Other Instruments’ Pitches (Master Tune)
For a cleaner ensemble sound while performing with one or more other instruments,
ensure that each instrument’s standard pitch is in tune with that of the other
instruments. In general, the tuning of an instrument is indicated by the pitch in Hertz
(Hz) of the middle “A” note.
This matching of other instruments’ basic reference pitches is called “tuning.”
When the instrument is turned on, the standard pitch is set to “440.0 Hz.”
fig.00c-10
2,6
2,4
3
1 5
1
2
Press [EDIT], getting the indicator to light.
The Edit Menu screen appears.
Press [INC] or [DEC] to select “System,” then press [ENTER].
The TONE SELECT button blinks.
fig.disp.SYS
3
4
Press [PIANO].
The parameter name (tun) appears in the display while [PIANO] is held down.
When the button is released, the last three digits of the currently set basic reference
pitch are shown in the display.
Press [INC] or [DEC] to change the standard pitch.
For faster value increases, keep
[INC] pressed down and press
[DEC]. For decreasing value
faster, keep [DEC] pressed
down and press [INC].
You can set the standard pitch anywhere in a range of 415.3 Hz to 466.2 Hz.
The pitch is lowered 0.1 Hz each time [DEC] is pressed. When the button is held
down, the pitch drops continuously.
The pitch is raised 0.1 Hz each time [INC] is pressed. When the button is held down,
the pitch rises continuously.
To return to the original pitch, press [DEC] and [INC] simultaneously.
5
6
If you want to save the settings, press [WRITE].
A confirmation screen appears.
fig.disp.Sur
If this setting has not been
saved, it is lost when the
power is turned off.
If you want to continue with the save, press [ENTER].
You can return to Step 2.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the RD-300SX
Basic Organization of the
RD-300SX
Units of Sound
Tone
The RD-300SX can be divided into two sections: a keyboard
The individual sounds used when playing the RD-300SX are referred
controller section and a sound generator section. The two sections
to as “Tones.”
are connected internally by means of MIDI.
fig.00d-01
The RD-300SX has 340 individual tones, and a variety of tones can be
used in performances.
Sound
Generator
Section
Part
A sound generator of this type which can control multiple sounds
using one device is referred to as a multitimbral sound generator.
The RD-300SX contains a multitimbral sound generator capable of
playing sixteen Tones simultaneously.
Play
“Parts” are where Tones that are created when the RD-300SX is used
as a sound generator are assigned. Different Tones can be assigned
to each of the Parts and controlled individually.
Keyboard Controller Section
(controllers such as keyboard, pitch bend lever, etc.)
*
external devices via MIDI or USB.
Keyboard Controller Section
Zone
This section includes the keyboard, the Pitch Bend/Modulation
lever, the panel knobs, and any pedal connected to the rear panel.
Actions such as pressing and releasing of keys on the keyboard,
depressing a pedal, and so forth, are converted to MIDI messages
and sent to the sound generator section, or to an external MIDI
device.
With the RD-300SX, you can freely control two of the above-
mentioned parts using the RD-300SX’s buttons and keys; these two
parts are referred to as the UPPER zone and LOWER zone. You can
layer each zone (Dual Play; p. 21) or play them in different ranges of
the keyboard (Split Play; p. 22).
Sound Generator Section
The sound generator section produces the sound. Here, MIDI
messages received from the keyboard controller section or external
MIDI device are converted to musical signals, which are then output
as analog signals from the OUTPUT and PHONES jacks.
Basic Operation of the RD-
300SX
Changing the Settings Values
When changing settings values, you can use [DEC] and [INC].
[DEC], [INC]
Pressing [INC] increases the value, and [DEC] decreases it. Keep the
button pressed for continuous adjustment. For faster value increases,
keep [INC] pressed down and press [DEC]. For decreasing value
faster, keep [DEC] pressed down and press [INC].
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Demo (Demo Play)
Here’s how to listen to the demo songs.
The RD-300SX comes with a total of eleven internal demo songs, including demo
All rights reserved.
songs that utilize and demonstrate the instrument’s special qualities, and others that
introduce you to the instrument’s tones.
Unauthorized use of this
material for purposes other
than private, personal
enjoyment is a violation of
applicable laws.
No. Song Name
d-1. Let's Hang Out
d-2. RD-300SX Piano
d-3. Stay Tuned
Composer/Copyright
Scott Tibbs © 2004 Roland Corporation
Scott Tibbs © 2004 Roland Corporation
Scott Tibbs © 2004 Roland Corporation
Scott Tibbs © 2004 Roland Corporation
981a
d-4. Tone Preview
* With d-4, there is one song in each of the tone categories for a total of eight demo songs.
fig.01-01
4
1
3
2
3
* The current settings are erased when demo song is played. Be sure that any settings you want
to keep are saved to a Setup (p. 35).
1
Hold down [EDIT] and press [WRITE].
The Demo screen appears.
fig.disp.d-1
No data for the music that is
played will be output from
MIDI OUT.
982
2
3
Press [INC] or [DEC] to select the song you want to hear.
Press [ENTER] to start the playback of the song.
While the demo songs are
playing back, playing the
keyboard will not produce
sound.
Playback of all the songs is repeated.
When you press the TONE SELECT button, d-4 is selected, and the demo song using
the tone from the category corresponding to the pressed button begins to play.
The selected TONE SELECT button lights up in red.
4
To stop a song while it is playing, press ONE TOUCH [PIANO].
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Piano Performances (ONE TOUCH [PIANO])
Now, try performing with the piano.
With the RD-300SX, you can call up the optimal settings for piano performances with
the press of a single button.
fig.01-04
1
1
Press ONE TOUCH [PIANO].
fig.disp.Pno
Pressing ONE TOUCH
[PIANO] restores all of the
settings to their status at the
If you want to save the
settings, store them to a Setup
(p. 35).
Pressing ONE TOUCH [PIANO] sets the entire keyboard to play with the piano
tone.
With the RD-300SX, you can adjust the keyboard touch to suit your own style of
piano performance. For more detailed information, refer to “Changing the
Keyboard’s Touch” (p. 26).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Performing with a Variety of Tones
The RD-300SX provides 340 types of Tones.
Each one of these individual sounds is called a tone.
For more on the RD-300SX’s
Tones are assigned to the TONE SELECT buttons according to the tone category
selected.
internal tones, refer to the
“Tone List” (p. 60).
Try selecting and performing with a number of different tones.
fig.01-06
1
2
3
1
Press ONE TOUCH [PIANO].
This selects a single tone to be played over the entire keyboard.
Tones selected with [RHY/
GM2] are registered in the
following order: “Rhythm
Sets,” “GM2 Rhythm Sets,”
and “GM2 Tones.” Refer to the
“Rhythm Set List” (p. 62).
2
3
Press any of the TONE SELECT buttons to select the tone category.
Press [INC] or [DEC] to select the tone.
The TONE SELECT button for the selected category lights.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Playing Multiple Tones with the Keyboard
The RD-300SX features four Internal zones (UPPER and LOWER), and one tone can
be assigned to each of these zones.
In each zone used, you can have multiple tones layered and played simultaneously
or have different tones played in the left and right parts of the keyboard.
These different ways of using tones are referred to as “keyboard modes.” There are
three keyboard modes.
• Single: One tone is played for the entire keyboard.
• Dual:
Two tones are layered and played together.
• Split:
The keyboard is divided into two separate ranges at a certain key (the
split point), with different tones played in the left and right ranges.
The two layered parts played in Dual mode are called the UPPER and LOWER parts.
In Split mode, UPPER refers to the part played in the right section of the keyboard,
while LOWER refers to the part played in the left section of the keyboard.
UPPER is played over the entire keyboard when the RD-300SX is set to Single mode.
fig.01-07
Dual mode
UPPER
LOWER
Split mode
Split point
LOWER
UPPER
Switching to Single Mode
and Split mode, to Single mode, in which a single tone is used throughout the entire
keyboard.
•
Pressing ONE TOUCH [PIANO]
This applies the piano tone to the entire keyboard, setting the optimal conditions for
piano performances.
However, pressing ONE TOUCH [PIANO] disables any settings made up to that
point. Be sure to save any settings you want to keep to a Setup (p. 35) before pressing
ONE TOUCH [PIANO].
•
Turning [DUAL] or [SPLIT] off (turning the indicator off)
In this case, the UPPER tone is applied to the entire keyboard.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Performing with Two Layered Tones ([DUAL])
fig.01-08
1, 2
1
“Changing the Tone for a
Press [DUAL], getting the indicator to light.
Zone” (p. 24)
Try fingering the keyboard.
fig.disp.tone1
“Adjust the Volume Level for
Individual Zones (ZONE
LEVEL sliders)” (p. 24)
The tones for UPPER and LOWER are layered and played.
When you press [DUAL], the [LOWER SELECT] indicator automatically light up,
and the LOWER tone number appears in the display. You can display the UPPER
TONE number by pressing [LOWER SELECT] so its indicator goes out.
2
Press [DUAL] once more, and the indicator light goes out.
The tone for UPPER played.
Pressing Two TONE SELECT buttons Simultaneously
You can layer two tones by pressing two TONE SELECT buttons simultaneously.
For example, if you want to layer a piano sound with strings, together press both
[PIANO] and [STRINGS].
[DUAL] starts to flash and when you begin playing the keyboard, the piano and
strings sounds are layered together.
When this is done, the tone for the button that is pressed down first (indicator lit in
red) is assigned to UPPER, and the other tone (indicator lit in orange) is assigned to
LOWER.
Once you have selected two TONE SELECT buttons, pressing either TONE SELECT
button then selects that tone as the [UPPER] tone, and the LOWER tone stops
playing.
* You cannot layer two tones when [SPLIT] is set to ON.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
([SPLIT])
Such a division of the keyboard into right- and left-hand sections is called a “Split,”
and the key where the division takes place is called the “Split Point.” The split-point
key is included in the LOWER section.
You can change the split point.
Please refer to “Changing the
The Split Point has been set at the factory to “B3.”
Keyboard’s Split Point” (p.
23).
fig.01-10
1, 2
1
“Changing the Tone for a
Press [SPLIT], getting the indicator to light.
Zone” (p. 24)
[LOWER SELECT] lights.
Try fingering the keyboard.
“Adjust the Volume Level for
Individual Zones (ZONE
LEVEL sliders)” (p. 24)
The UPPER tone plays in the right-hand section of the keyboard, and the LOWER
tone plays in the left-hand section.
fig.01-12
Split Point (B3)
LOWER
UPPER
2
To exit Split mode, press [SPLIT] once more, and the indicator light goes out.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Changing the Keyboard’s Split Point
You can change the point at which the keyboard is divided (the Split Point) in Split
mode.
1
2
Hold down [SPLIT] for several seconds.
You can also change the split
point by holding down [SPLIT]
and pressing [INC] or [DEC].
A screen such as the following appears, and the current value of the setting is
displayed.
fig.disp.b3
While holding down [SPLIT], press the key that you want to use as the split
point.
The key for the split point
appears in the display as
You can adjust the split point in semitone increments.
When you release [SPLIT], the previous display will reappear.
shown below.
fig.01-11
* The split-point key is included in the LOWER section.
fig.01-13
Display
Letter
B3 (when the power is turned on)
C
E
C
F
D
F
E
G
B
name
Display
Letter
name
A0
B7
Display
Range in which the split point can be set
Letter
name
A
A
B
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Changing the Tone for a Zone
When changing the tone assigned to a zone in Dual or Split mode, use [LOWER
SELECT] to specify the zone with the tone you want to change.
fig.01-14
1
2
2
1
2
If you want to select UPPER, press [LOWER SELECT] until the indicator is off.
When you want to select LOWER, press [LOWER SELECT] until the indicator
is green.
[LOWER SELECT] is disabled
when [DUAL] or [SPLIT] is
switched off.
fig.01-15
When selecting the UPPER zone
When selecting the LOWER zone
The TONE SELECT button indicators are red when the UPPER zone is selected and
green when the LOWER zone is selected. In either zone, if tones from the same
category are selected, the button's indicator lights in orange.
Select the tone category with a TONE SELECT button, then select the tone
with [INC] or [DEC].
Adjust the Volume Level for Individual Zones (ZONE LEVEL sliders)
fig.01-16
The RD-300SX features two parts you can freely control using the instrument’s
buttons and keys; these two parts are called the UPPER zone and LOWER zone.
You can adjust the volume for each zone using the ZONE LEVEL sliders.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Transposing the Key of the Keyboard ([TRANSPOSE])
You can transpose performances without changing the keys you are playing, as well
as change the pitch by an octave. This feature is called “Transpose.”
This is a convenient feature to use when you want to match the pitch of the keyboard
performance to a vocalist’s pitch, or perform using the printed music for trumpets or
other transposed instruments.
Note messages from MIDI IN
The reference Transpose setting is C4, and the setting can be adjusted in semitone
units in a range of -48-0- +48.
will not be transposed.
fig.01-17
1, 2, 3
1
Hold down [TRANSPOSE] for several seconds.
A screen such as the following appears, and the current value of the setting is
displayed.
fig.disp.0
Even when the Transpose
function is turned on, the Split
Point (p. 23) remains
unchanged.
2
Hold down [TRANSPOSE] and press a key.
For example, to have “E” sound when you play “C” on the keyboard, hold down
[TRANSPOSE] and press the E4 key. The degree of transposition then becomes “+4.”
You can also change a key by
holding down [TRANSPOSE]
When you release [TRANSPOSE], the previous display will reappear.
When the amount of transposition is set, the Transpose function switches on, and
[TRANSPOSE] lights up.
You can make different Key
Transpose settings for each
zone. Refer to “Changing the
pitch of the tone in semitone
steps (Key Transpose)” (p.
43).
3
To turn off Transpose, press [TRANSPOSE] so that its indicator goes off.
The next time [TRANSPOSE] is pressed, the sound is transposed by an amount
corresponding to the value set here.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Changing the Keyboard’s Touch
You can change the touch sensitivity, or response of the keys.
When the instrument is turned on, this is set to “M (Medium).”
fig.01-19
1, 3
1
2
1
2
Hold down [SHIFT] and press [LOWER SELECT].
With certain sounds, the touch
may not change.
[SHIFT] blinks.
The currently selected keyboard touch appears in the display.
fig.disp.-M-
Press [INC] or [DEC] to select the touch.
Indicate
Description
The sound plays at one set volume, regardless of the force used to
play the keys.
Fixed
Light
A light keyboard touch is selected. You can achieve fortissimo (ff)
play with a less forceful touch than usual, so the keyboard feels
lighter. This setting makes it easy to play, even for children.
This sets the standard keyboard touch. You can play with the
most natural touch. This is the closest to the touch of an acoustic
piano.
Here, a heavy keyboard touch is selected. You have to finger the
keyboard more forcefully than usual in order to play fortissimo
(ff), so the keyboard touch feels heavier. Dynamic fingering adds
even more feeling to what you play.
Medium
Heavy
3
Press [SHIFT], and the indicator light goes out.
Changing the Velocity When the Key Touch Is Set to “Fixed”
This sets the velocity the sound will have when the keyboard touch is set to “Fixed.”
1
When “OFF” is selected in Step 2 above, holding down [LOWER SELECT] and
pressing [INC] or [DEC] changes the velocity of the sound.
You can set this to any value from 1 to 127.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Adding Reverberation to Sounds ([REVERB])
You can apply a reverb effect to the notes you play on the keyboard. With the reverb
effect, you obtain a pleasant reverberation, making it sound as if you were
performing in a concert hall or similar space.
fig.01-21
1, 2
1
2
Press [REVERB], getting its indicator to light.
Try fingering the keyboard.
The reverb effect is applied to the entire tone.
To eliminate the Reverb effect, press [REVERB] once more, extinguishing the
indicator.
Changing the Reverb Effect Type
You can select from four different reverb effect types.
1
While holding down [SHIFT], press [REVERB].
2
Press [INC] or [DEC] to switch the reverb type.
Displayed
Description
Reverb present in normal rooms
ROOM
Reverb found in larger halls
Reverb of church cathedrals
Reverb for use with GM2
HALL
CATHEDRAL
GM REVERB
3
After determining the type, press [SHIFT] to return to the previous screen.
Changing the Depth of Reverb Effect (Reverb Depth)
You can select from 127 levels of depth for the reverb effect.
Reverb depth settings can be
made independently for each
zone (p. 41).
1
Hold down [REVERB] and press [INC] or [DEC] to change the depth of the
reverb effect.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Adding a Variety Effects to the Sound ([MULTI EFFECTS])
In addition to reverb (p. 27), you can apply a variety of changes to the RD-300SX’s
sounds. These are referred to as “multi effects.” With the RD-300SX, you can select
from 78 different effect types.
Effects may not be applied
with some of sounds.
With the factory default settings, effects have been preselected for each tone.
fig.01-23
1, 2
1
Press [MULTI EFFECTS], getting its indicator to light.
You can specify which zone is
Try fingering the keyboard.
to have priority when the
effects assigned to the Upper
zone and the Lower zone differ.
Refer to “Setting the Zone to
which Multi Effects are
The effect is applied to the currently selected tone.
2
To remove the effect, press [MULTI EFFECTS] once more, extinguishing the
indicator.
Added (MFX Zone)” (p. 40).
Changing the Depth of Effect
You can change the levels of depth for the effect.
The content and range vary according to the MFX type. For more detailed
information, refer to “Effects List” (p. 55).
You can change the effect type.
Refer to “Changing the Multi-
effects Type” (p. 29).
1
Hold down [MULTI EFFECTS] and press [INC] or [DEC].
The depth for the effect being applied to the currently selected tone appears in the
display.
The next time you choose the same tone, the effect with the depth you’ve selected
here is applied.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Changing the Multi-effects Type
1
While holding down [SHIFT], press [MULTI EFFECTS].
For more on the RD-300SX’s
internal effect types, refer to
the “Effects List” (p. 55).
The effect number appears in the display.
2
Press [INC] or [DEC] to select the effect type.
3
After determining the type, press [SHIFT] to return to the previous screen.
Adding a Spinning Sound to Organ Tones (Rotary Effect)
The Rotary effect is applied to some Organ tones you can select with the [ORGAN]
button. When one of these tones is selected, you can use the [MULTI EFFECTS]
To prevent the Rotary effect
button to change the speed of the rotary effect.
from being applied, select an
effect type other than the
Rotary effect and then remove
the effect (p. 29).
What the rotary effect does is to add a “spinning” effect similar to the sound of an
organ using a rotating speaker.
1
2
Press [ORGAN] and select the organ tone.
When a tone that has the Rotary effect added is selected, the [MULTI EFFECTS]
button’s indicator flashes.
You can apply the rotary effect
to tones other than the organ
tones as well.
Each time pressing [MULTI EFFECTS], switch the speed of the rotary effect
between fast and slow rotation.
When the [MULTI EFFECTS] button’s indicator flashes, a more fast rotary effect is
applied.
When the [MULTI EFFECTS] button’s indicator blinks, a slower rotary effect is
applied.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Changing the Sound’s Pitch in Real Time
(Bender/Modulation Lever)
While playing the keyboard, move the lever to the left to lower the pitch, or to the
right to raise the pitch. This is known as Pitch Bend.
The effect obtained when you
move the lever may differ
according to the tone being
used. Additionally, the effect
applied by moving the lever is
predetermined for each tone,
and cannot be changed.
You can also apply vibrato by manipulating the lever away from you. This is known
as Modulation.
If you move the lever away from you and at the same time move it to the right or left,
you can apply both effects simultaneously.
fig.01-25
Modulation
Pitch Bend
Making a More Consistent Sound ([SOUND CONTROL])
Switching on the Sound Control function suppresses differences in volume for a
more consistent sound.
Sounds may become distorted
with certain tones. In such
1
instances, lower the zone
Press [SOUND CONTROL], getting its indicator to light.
volume.
2
While holding down [SOUND CONTROL], press [INC] or [DEC] to change the
type.
Displayed
Description
Applies strong compression.
Hard Comp
Soft Comp
Low Boost
Mid Boost
High Boost
Applies mild compression.
Boosts the low end.
Boosts the midrange.
Boosts the high end.
3
To remove this function, press [SOUND CONTROL] once more, extinguishing
the indicator.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with the Keyboard
Adjusting the Level of the Sound’s Low and
High-Frequency Ranges (EQUALIZER)
The RD-300SX is equipped with a two-band equalizer.
You can adjust the levels of the low-frequency and high-frequency ranges using the
Equalization is applied to the
overall sound output from the
OUTPUT jacks.
EQUALIZER [LOW] and [HIGH] knobs, respectively.
fig.01-26
Sounds may distort at certain
knob settings. If this occurs,
lower the volume level in the
zones using the respective
ZONE LEVEL sliders.
1
Turn the EQUALIZER knobs to adjust the levels in each range.
Turning a knob towards the minus (-) sign cuts the level of that frequency range; turn
the knob towards the plus (+) sign to boost the level of that range.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Convenient Functions in Performances
Playing Rhythm ([RHYTHM])
The RD-300SX features internally programmed drum patterns in a variety of musical
genres, including jazz, rock, and more, that you can use as accompaniment for your
performances on the RD-300SX. These drum patterns are known as “rhythms.”
fig.02-01
1, 2
1
Press [RHYTHM] to make the button indicator light.
The Rhythm begins playing.
2
Press [RHYTHM] once more; the indicator goes out, and the Rhythm stops
playing.
Changing the Rhythm Pattern
You can select the way a Rhythm is played (the pattern) to match a variety of
different musical genres.
For more information about
the kind of Rhythm Patterns,
1
please refer to “Rhythm
Press [RHYTHM] to make the button indicator light.
Pattern List” (p. 65).
The Rhythm begins playing.
2
While holding down [RHYTHM], press [INC] or [DEC] to select a pattern.
The Rhythm’s pattern changes.
fig.disp_r1
Rhythm pattern performance
3
data is not output from the
MIDI OUT connector nor the
USB connector when MIDI Tx
Mode (p. 46) is set to Mode 1.
If you press [RHYTHM] once more, the indicator light goes out, and the
Rhythm stops playing.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Convenient Functions in Performances
Changing Rhythm Tempos
1
While holding down [SHIFT], press [RHYTHM].
The way Rhythm is played and
the tempo display may differ
with some Rhythm Patterns.
The rhythm tempo is displayed.
2
Press [INC] or [DEC] to change the tempo.
The Rhythm are played at the selected tempo.
3
Press [SHIFT] to return to the previous screen.
Changing the Rhythm Volume
1
While holding down [RHYTHM], move the ZONE LEVEL slider.
The volume of the rhythm changes.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Convenient Functions in Performances
Selecting Stored Settings ([SETUP])
The RD-300SX’s tone settings, effect settings, and other such settings are collectively
referred to as a “Setup.”
The current settings are erased
when a Setup is called up. Be
sure to save any Setup you
would like to keep first before
calling up another Setup (p.
35).
Once you’ve stored your preferred settings, and settings for the songs to be
performed as a Setup, you can then switch whole groups of settings during a
performance just by switching Setups.
You can store up to 32 different Setups.
The RD-300SX is shipped from the factory with recommended Setups already
prepared.
Now try actually calling up a Setup.
fig.02-02
1
2
2
1
2
Press [SETUP], getting the indicator to light.
“Setup List” (p. 66)
The Setup screen, shown below, appears in the display.
fig.disp.SUP
Press [INC] or [DEC], or TONE SELECT buttons to select a Setup.
fig.disp.S11
S.11 S.21 S.31 S.41 S.51 S.61 S.71 S.81
S.12 S.22 S.32 S.42 S.52 S.62 S.72 S.82
S.13 S.23 S.33 S.43 S.53 S.63 S.73 S.83
S.14 S.24 S.34 S.44 S.54 S.64 S.74 S.84
Setup
Number
When Selecting with the TONE SELECT Buttons
3
Try playing the keyboard.
The settings are switched to those of the Setup that has been called up.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Convenient Functions in Performances
Storing Settings to Setups ([WRITE])
If you want to use the changed content as a new Setup, use the following procedure
to save the settings to a Setup.
You can store 32 Setups on the RD-300SX.
fig.02-05
1
3, 4
2
2
1
Press [WRITE], getting the indicator to light.
The Setup screen appears.
fig.disp.S11
2
3
Select the save-destination Setup, either by pressing [INC] or [DEC], or TONE
SELECT buttons.
Press [ENTER].
fig.disp.Sur
A confirmation screen (Sure?) appears.
If you do not want to save the Setup, press [EXIT] or [WRITE].
The operation is cancelled, and you are returned to the Tone screen.
4
When [ENTER] is pressed, saving of the Setup begins.
When you have finished saving the Setup, the [WRITE] indicator goes out.
You are returned to the Tone screen.
The following settings cannot be saved to a Setup.
• System settings (p. 37)
• SOUND CONTROL settings (p. 30)
• EQUALIZER Knob Position (p. 31)
• V-LINK settings (p. 51)
• Transpose (p. 25)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Convenient Functions in Performances
Disabling the Buttons (Panel Lock)
Once Panel Lock is engaged, all buttons (except for the VOLUME slider, ONE
TOUCH [PIANO], and the [EXIT] button) will not function. This prevents settings
from being changed inadvertently on stage or in other such situations.
fig.02-06
2
2
1
1
2
While holding down [EDIT], press [ENTER].
Then, continue to hold down these two buttons by following display will appear.
fig.disp.—
Press ONE TOUCH [PIANO] or [EXIT] to cancel Panel Lock.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
The process of changing tone parameters to create the tones you like,
and changing the settings for various functions is known as
“editing.”
(System)
When [EDIT] is pressed and the indicator is lit, the RD-300SX
switches to “Edit mode.”
Functions that affect the RD-300SX’s overall operating environment
You can save edited settings to Setups.
are called “System functions.”
Edited settings are discarded when the RD-300SX’s power is turned
off, so be sure that any settings you want to keep are saved to a Setup.
For details, refer to “Storing Settings to Setups ([WRITE])” (p. 35).
How to Make Settings
However, you cannot save System content to the Setups. If you want
to save changes made to the system, perform the Write procedure
separately (p. 37).
1. Press [EDIT].
The indicator lights, and the RD-300SX switches to Edit mode.
2. Press [INC] or [DEC] to select “System,” then press
[ENTER].
fig.disp.SYS
Parameters That Can Be Set
You can set the following parameters in Edit mode.
System: Settings related to the functioning of the entire instrument
(p. 37)
Master Tune
Stretch Tune
Damper Pedal Polarity
Control Pedal Polarity
Setup Control Channel
Setup Pedal Shift
USB Driver
3. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned.
The parameter name appears in the display while the button is
held down. When the button is released, the value for the
parameter is shown in the display.
TONE
Indication
Parameter
SELECT
button
Common: Settings for pedal functions and other such functions
(p. 40)
PIANO
Master Tune (p. 38)
MFX Zone
Control Pedal Function
Tone: Tone settings (p. 41)
Cutoff
E.PIANO
ORGAN
Temperament, Key (p. 38)
Stretch Tune (p. 38)
Resonance
Attack Time
Decay Time
Release Time
Reverb Send Level
Fine Tune
STRINGS/
PAD
Damper Pedal Polarity (p. 38)
Control Pedal Polarity (p. 39)
Setup Control Channel (p. 39)
Setup Pedal Shift (p. 39)
USB Driver (p. 39)
GUITAR/
BASS
BRASS/
WINDS
Bend Range
Upper, Lower Zone: Zone settings (p. 42)
Key Transpose
VOICE/
SYNTH
Pan
RHY/GM2
Damper Pedal Switch
Control Pedal Switch
Bender Switch
4. Press [INC] or [DEC] to set the value.
Modulation Switch
Part: Part On/Off (p. 43)
1–16
5. If you want to save the setting, press [WRITE]. Then, press
[ENTER].
Utility: Settings for backing up, Factory Reset, etc. (p. 44)
Bulk Dump Temporary
Bulk Dump Setup
Factory Reset
You can return to Step 2 by pressing [EXIT].
TX Mode
Local Control
Unless they have been saved, these settings are lost when the
power is turned off.
*
Some tones are set so no effects are applied.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Selecting the Keynote
Tuning to Other Instruments’
Pitches (Master Tuning)
When playing with tuning other than equal temperament, you need
to specify the keynote for tuning the song to be performed (that is,
the note that corresponds to C for a major key or to A for a minor
key). (If you choose an equal temperament, there’s no need to select
a keynote.)
For a cleaner ensemble sound while performing with one or more other
instruments, ensure that each instrument’s standard pitch is in tune with
that of the other instruments. In general, the tuning of an instrument is
indicated by the pitch in Hertz (Hz) of the middle “A” note.
The last three digits of the current standard pitch setting appear in
the display.
Set the keynote by holding down [E.PIANO] and pressing [INC] or
[DEC].
The selected keynote appears in the display as shown below.
fig.03-01
Value
Display
Letter
name
415.3Hz – 466.2Hz (0.1 Hz increments)
C
D
D
E
E
F
F
G
A
A
B
B
*
When performing in ensemble with other instruments, be aware that
depending on the key, there may be some shifting of the pitch. Tune the
RD-300SX to the fundamental pitch of the other instruments.
Adjusting the Tuning
(Temperament, Key)
This sets the tuning and keynote (tonic) for entire parts.
fig.disp.1-C
Precise Modification of Chord
Sonorities (Stretch Tune)
Changes the pitch using the “stretch tuning” method typically used
on acoustic pianos. This makes high-range sounds slightly higher in
pitch, and low-range sounds slightly lower in pitch.
Temperament Keynote
Most modern songs are composed and played with the assumption
that equal temperament will be used, but when classical music was
composed, there were a wide variety of other tuning systems in
existence. Playing a composition with its original tuning lets you enjoy
the sonorities of the chords that the composer originally intended.
Indication
Value
OFF
ON
You can select from eight tunings.
Indi-
Tuning
Description
cation
Switching the Pedal’s Polarity
(Damper Pedal Polarity)
1
2
3
4
Equal
Temperament
This tuning divides an octave into 12
equal parts. Every interval produces
about the same amount of slight disso-
nance.
This scale eliminates dissonance in
fifths and thirds. It is unsuited to play-
ing melodies and cannot be transposed,
but is capable of beautiful sonorities.
The scales of the major and minor just
intonations are different. You can get
the same effect with the minor scale as
with the major scale.
This scale devised by the philosopher
Pythagoras eliminates dissonance in
fourths and fifths. Dissonance is pro-
duced by third-interval chords, but mel-
odies are euphonious.
This switches the polarity of the pedal connected to the PEDAL
(DAMPER) jack on the rear panel.
Just (Major)
Just (Minor)
Pythagorean
On some pedals, the electrical signal output by the pedal when it is
pressed or released is the opposite of other pedals. If your pedal has
an effect opposite of what you expect, set this parameter to REVERSE.
If you are using a Roland pedal (that has no polarity switch), set this
parameter to STANDARD.
Indication
Value
STANDARD
REVERSE
5
Kirnberger
This scale is a modification of the meantone
and just intonations that permits greater
freedom in transposition to other keys. Per-
formances are possible in all keys (III).
6
7
8
Mean Tone
Werckmeister
Arabic
This scale makes some compromises in
just intonation, enabling transposition
to other keys.
This is a combination of the mean tone
and Pythagorean scales. Performances are
possible in all keys (first technique, III).
Arabic Scale. This scale is suitable for
Arabic music.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Switching the Pedal’s Polarity
(Control Pedal Polarity)
Using the Pedal to Switch Setup
(Setup Pedal Shift)
This switches the polarity of the pedal connected to the PEDAL
(CONTROL) jack on the rear panel.
You can use the pedal which is connected to the PEDAL (CONTROL)
jack on the rear panel as a dedicated switch for selecting Setup in
order.
On some pedals, the electrical signal output by the pedal when it is
pressed or released is the opposite of other pedals. If your pedal has
an effect opposite of what you expect, set this parameter to REVERSE.
If you are using a Roland pedal (that has no polarity switch), set this
parameter to STANDARD.
Indication
Value
Description
OFF
You can use the pedal function
set with Control Pedal Func-
tion (p. 40).
ON
This becomes a dedicated
switch for switching Setups.
Indication
Value
STANDARD
The function set with Control Pedal Function (p. 40) cannot be
used when this is switched to ON.
REVERSE
Making the Settings for the USB
Driver
Using Program Change Messages
to Switch Setups
If you intend to connect to a computer using the USB connector, you
need to make the following setting before you make the connection.
(Setup Control Channel)
You can switch the RD-300SX’s Setups with MIDI messages from an
external MIDI device.
After changing settings, turn the power off and then on again.
Set the MIDI Receive channel for receiving the MIDI messages
(Program Changes) from the external MIDI device to be used for
switching Setups.
There is no need to use the Write procedure for the USB Driver
settings.
When not switching Setups from an external MIDI device, set this to
OFF.
Indication
Value
Description
Original
Select this when using the supplied
driver with a USB connection.
Value
1–16, OFF
Generic
Select this when using a gener-
ic USB driver included with the
OS with a USB connection.
When the Control Channel settings are transmitted along with
the part’s MIDI receive channel, switching of Setups takes
priority over the switching of tones. For more on program
changes for switching Setups, refer to “Switching Setups” (p.
49).
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Setting the Zone to which Multi
Effects are Added (MFX Zone)
Setup-Related Settings
(Common)
This specifies which zone is to have priority when the effects
assigned to the Upper Tone and Lower Tone differ in Split mode or
Dual mode (p. 20).
How to Make Settings
1. Press [EDIT].
Indication
Description
UPPER
The indicator lights, and the RD-300SX switches to Edit mode.
2. Press [INC] or [DEC] to select “Common,” then press
[ENTER].
fig.disp.Con
LOWER
*
If same effects are assigned to the Upper Tone and Lower Tone, the
same effects are added to both of Tones.
3. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned.
The parameter name appears in the display while the button is
held down. When the button is released, the value for the
parameter is shown in the display.
Changing the Pedal Function
This sets the function of the pedal switch or expression pedal (such
as the optional EV-5) connected to the CONTROL jack on the rear
panel.
TONE
Indication
Parameter
SELECT
button
PIANO
This function cannot be used when Setup Pedal Shift is
switched to ON (p. 39) .
MFX Zone (p. 40)
Indication
Description
Soft (Default)
E.PIANO
ORGAN
STRINGS/
PAD
Control Pedal Function (p. 40)
—
—
—
—
Sostenuto
GUITAR/
BASS
BRASS/
WINDS
VOICE/
SYNTH
RHY/GM2
—
—
—
—
—
—
—
—
Expression
Rhythm Start/Stop
Multi-effects ON/OFF
Modulation
Only the indicators of buttons to which a parameter is assigned
blink.
4. Press [INC] or [DEC] to set the value.
5. Press [EDIT] to turn off the indicator and quit editing.
You can return to Step 2 by pressing [EXIT].
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Changing Tone Elements
Tone Settings
(Cutoff/Resonance/Attack Time/
Decay Time/Release Time)
(Tone Parameter)
You can make changes in tones by adjusting the settings of the
following five elements.
How to Make Settings
Cutoff:
Adjusts how much the filter is opened.
1. Press [EDIT].
The indicator lights, and the RD-300SX switches to Edit mode.
Resonance: This boosts the portions in the region around the
cutoff frequency, lending a particular quality to the
sound. Excessively high settings can produce
2. Press [INC] or [DEC] to select “Tone,” then press [ENTER].
fig.disp.ton
oscillation, causing the sound to distort.
Attack Time: The time it takes after the key is pressed for a sound
to reach full volume.
Decay Time: The time it is to take following the attack for the
volume to decrease.
3. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned.
The parameter name appears in the display while the button is
held down. When the button is released, the value for the
parameter is shown in the display.
Release Time: The time it takes after the key is released for a sound
to become inaudible.
Making abrupt changes in the settings values may cause the
sound to become distorted or overly loud. Carefully monitor
volume levels while making the settings.
When setting the LOWER zone, set [LOWER SELECT] to ON.
Parameter
Value
Description
Cutoff
-64–0– +63
Higher values brighten the sound;
lower values make the sound seem
darker.
Higher value makes the special
quality of the sound stronger;
lower value reduce these charac-
teristics.
Higher values produce a milder at-
tack; lower values produce a sharper
attack.
The time it takes for the volume to
fall increases as the value is
raised; lowering the value de-
creases the decay time.
TONE
SELECT
button
Indication
Parameter
Resonance
-64–0– +63
PIANO
Cutoff (p. 41)
E.PIANO
ORGAN
Resonance (p. 41)
Attack Time (p. 41)
Decay Time (p. 41)
Release Time (p. 41)
Reverb Send Level (p. 41)
Fine Tune (p. 42)
Attack Time
Decay Time
-64–0– +63
-64–0– +63
STRINGS/
PAD
GUITAR/
BASS
Release Time
-64–0– +63
Higher values produce longer decay;
set lower values for a clear-cut sound.
BRASS/
WINDS
The effect may not be apparent with some tones, even when the
value is changed.
VOICE/
SYNTH
RHY/GM2
Bend Range (p. 42)
Setting the Amount of Reverb Applied
to Each Tone (Reverb Send Level)
This sets the depth of the reverb effect for each tone.
Only the indicators of buttons to which a parameter is assigned
blink.
When this value is set to “0,” no effect is applied even when
[REVERB] is pressed.
4. Press [INC] or [DEC] to set the value.
5. Press [EDIT] to turn off the indicator and quit editing.
You can also make the setting by holding down [REVERB] and
adjusting the ZONE LEVEL slider.
You can return to Step 2 by pressing [EXIT].
Value
0–127
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Changing the Pitch (Fine Tune)
Making the Settings for
Each Zone Individually
(Zone Parameter)
Adjusts the pitch of the tone’s sound up or down in 1-cent steps
(+/-50 cents).
Value
-50 – 50 (cent)
How to Make Settings
1. Press [EDIT].
One cent is 1/100th of a semitone.
The indicator lights, and the RD-300SX switches to Edit mode.
2. Press [INC] or [DEC] to select “U-L,” then press [ENTER].
Changing the Bend Range
(Bend Range)
fig.disp.U-L
This sets the amount of pitch change that will occur when you move
the Pitch Bend lever in semitone increments (+/-2 octaves).
3. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned.
The parameter name appears in the display while the button is
held down. When the button is released, the value for the
parameter is shown in the display.
Value
0–24
When setting the LOWER zone, set [LOWER SELECT] to ON.
TONE
Indication
Parameter
SELECT
button
PIANO
Key Transpose
Pan
E.PIANO
ORGAN
Damper Pedal Switch
Control Pedal Switch
Bender Switch
Modulation Switch
STRINGS/
PAD
GUITAR/
BASS
BRASS/
WINDS
VOICE/
SYNTH
RHY/GM2
—
—
—
—
Only the indicators of buttons to which a parameter is assigned
blink.
4. Press [INC] or [DEC] to set the value.
5. Press [EDIT] to turn off the indicator and quit editing.
You can return to Step 2 by pressing [EXIT].
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Changing the pitch of the tone in
semitone steps (Key Transpose)
Part On/Off (Part)
You can choose whether or not to have messages from external MIDI
devices be received by each individual part.
Value
-48—0— 48
1. Press [EDIT].
The indicator lights, and the RD-300SX switches to Edit mode.
2. Press [INC] or [DEC] to select “Part,” then press [ENTER].
fig.disp.Prt
Setting the Pan
The Pan setting localizes the sound image of each part when the
output is in stereo. With an increase in the value for L, more of the
sound will be heard as coming from the left side. Similarly, more of
the sound will originate at the right if the value of R is increased.
When set to 0, the sound is heard as coming from the center.
3. Referring to the following, press the TONE SELECT button
to which the part number you want to change is assigned.
Press [LOWER SELECT] so that the indicator lights to select
Part 9–16.
Value
The channel number appears in the display while the button is
held down. When the button is released, the status of the
channel (on/off) is shown in the display.
L64–0–R63
Turning Each Controller On and Off
TONE SELECT
button
PIANO
E.PIANO
ORGAN
STRINGS/PAD
GUITAR/BASS
BRASS/WINDS
VOICE/SYNTH
RHY/GM2
Part
Part
LOWER SELECT=OFF
LOWER SELECT=ON
These settings determine whether each individual part is controlled
(ON), or not (OFF) by the pedals connected to each PEDAL jack
(DAMPER, CONTROL), the Modulation lever, and the Bender.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Parameter
Value
Damper Pedal Switch
Control Pedal Switch
Pitch Bender Switch
Modulation Switch
OFF, ON
4. Press [INC] or [DEC] to switch the setting to ON or OFF.
The indicator for the currently selected part flashes, while the
indicator for a part that is ON lights steadily.
5. Press [EDIT] to turn off the indicator and quit editing.
You can return to Step 2 by pressing [EXIT].
On the RD-300SX, UPPER is fixed as Part 1 (Ch 1), while
LOWER is fixed as Part 2 (Ch 2). Note that the keyboard won’t
produce sound if Parts 1 and 2 are set to OFF.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Bulk Dump Temporary
The content of the currently selected Setup is transmitted.
5. Press [PIANO].
Utility Settings (Utility)
The following screen appears, and [PIANO] flashes.
fig.disp.bdt
Transferring Setups to External
Devices (Setup Bulk Dump)
You can transfer the contents of Setups to an external MIDI device.
This operation is called “bulk dump.”
Use this procedure to save the data to an external MIDI device in
situations such as when you want to perform by connecting another
RD-300SX with the same settings, or to prevent your Setups from
corruption.
6. Put the external sequencer in record mode.
7. Press [ENTER].
A confirmation screen (Sure?) appears.
If you do not want to transmit the settings, press [EXIT].
1. Connect the RD-300SX and the external sequencer, using
8. Press [ENTER] again to transmit the settings.
an optional MIDI or USB cable (sold separately).
When the transfer is completed, you can return to Step 3.
2. Press [EDIT].
9. Stop the external sequencer.
The indicator lights, and the RD-300SX switches to Edit mode.
3. Press [INC] or [DEC] to select “Utility,” then press [ENTER].
Bulk Dump Setup
fig.disp.Utl
The content of all Setups is transmitted.
5. Press [E.PIANO].
The following screen appears, and [E.PIANO] flashes.
fig.disp.bdS
4. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned,
then select the parameter.
TONE SELECT
button
Indication
Description
6. Put the external sequencer in record mode.
PIANO
Bulk Dump Temporary
(p. 44).
7. Press [ENTER].
A confirmation screen (Sure?) appears.
If you do not want to transmit the settings, press [EXIT].
E.PIANO
ORGAN
Bulk Dump Setup (p. 44).
Factory Reset (p. 45).
TX Mode (p. 46)
8. Press [ENTER] again to transmit the settings.
When the transfer is completed, you can return to Step 3.
STRINGS/
PAD
9. Stop the external sequencer.
GUITAR/
BASS
Local Control (p. 46)
BRASS/
WINDS
VOICE/
SYNTH
—
—
—
—
—
—
RHY/GM2
Only the indicators of buttons to which a parameter is assigned
light.
Stop the rhythms and do not touch the keys or controllers when
performing the Bulk Dump procedure.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Restoring Saved Settings to the RD-
300SX
factory condition (Factory Reset)
When returning settings saved to an external sequencer back to
the RD-300SX, an Exclusive message is transmitted from the
external sequencer, then the data is received by the RD-300SX.
The settings stored in the RD-300SX can be returned to their factory
settings.
Be aware that when you restore Setups data to the RD-300SX,
the data in the RD-300SX will be overwritten and lost.
Executing “Factory Reset” results in deletion of the Setups (p.
34) and the System (p. 37). If you want to keep any data you
have stored, use the “Bulk Dump Setup” operation to save the
data to an external sequencer (p. 44).
1. Connect the RD-300SX and the external sequencer, using
an optional MIDI or USB cable (sold separately).
2. Make sure that [EDIT] indicator is extinguished.
*
You cannot save the System settings by Bulk Dump.
If the [EDIT] indicator is lit, press [EDIT] to turn the indicator
light off and put the RD-300SX in normal performance mode.
1. Press [EDIT].
The indicator lights, and the RD-300SX switches to Edit mode.
3. Transmit (play back) the data from the external sequencer.
2. Press [INC] or [DEC] to select “Utility,” then press [ENTER].
fig.disp.Utl
After playback of the Bulk Dump Setup data, the RD-300SX
writes the data to the internal memory. Be sure never to turn off
the power while this data is being written.
For details on transmitting exclusive data, refer to the owner’s
manual for your sequencer.
3. Press [ORGAN].
fig.disp.Fctl
4. Press [ENTER].
A confirmation screen (Sure?) appears.
To cancel the Factory Reset, press [EXIT].
5. Press [ENTER] again to start the Factory Reset operation.
When the Factory Reset is completed, you can return to Step 2.
Never turn off the power during Factory Reset.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings for Each Function ([EDIT])
Setting the MIDI Tx Mode
Switching Local Control On and Off
By setting the MIDI Tx Mode, you can select to have a more suitable
(to the external MIDI device) selection of MIDI data be output from
the RD-300SX when you make tone changes on the RD-300SX.
“Mode 1” is the power-up default setting.
When connecting a MIDI sequencer, set Local Control to “Off.”
When the instrument is turned on, this is set to “On.”
As illustrated, information describing what has been played on the
keyboard is passed to the internal sound generator over two
different routes, (1) and (2). As a result, you hear overlapping or
intermittent sounds. To prevent this from happening, route (1) must
Indication
Value
Description
be severed, by setting the unit to what is known as “Local Off.”
fig.03-02
Mode1
This setting is suited for con-
necting to a sound module. The
MIDI information (for exam-
ple: Program change) is not
output from the RD-300SX
when you make a tone change
on the RD-300SX.
This setting is suitable for the
connection of sequencers. The
MIDI information (for example:
Bank select, Program Change,
Settings of Effects, and so on) is
output from the RD-300SX
when you make a tone change
on the RD-300SX.
Local On
(1)
Sequencer
Memory
MIDI
OUT
MIDI
IN
Sound
Generator
Mode2
MIDI
OUT
MIDI
IN
Thru function On
(2)
Each note played
is sounded twice
Local Control ON: The keyboard and the internal sound generator
are in a linked state.
fig.03-03
Sound is emitted
The MIDI Tx button is disabled in Mode 2.
Sound Generator
Local On
Local Control OFF: The keyboard and the internal sound generator
are in an unlinked state. No sound will be
produced by the keyboard when it is played.
fig.03-04
No sound produced
Sound Generator
Local Off
Indication
Value
OFF
ON
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting External MIDI Devices
What’s MIDI?
MIDI (Musical Instrument Digital Interface) is a standard
specification that allows musical data to be exchanged between
electronic musical instruments and computers. By using a MIDI
cable to connect devices that have MIDI connectors, you can create
an ensemble in which a single MIDI keyboard can play multiple
instruments, or change settings automatically as the song progresses.
Using the RD-300SX As a
Master Keyboard
By connecting an external MIDI device to the MIDI OUT connector
on the RD-300SX’s rear panel, you can then control the external MIDI
device with the RD-300SX.
Normally, the RD-300SX transmits Note messages from the MIDI
OUT connector, but you can control not only Note messages, but a
variety of other external MIDI device settings as well.
Make the following settings if you do not want to have MIDI
messages transmitted.
About MIDI Connectors
The RD-300SX has the following two types of MIDI connector. Their
1. Hold down [SHIFT] and press [MIDI Tx].
functions differ as described below.
fig.04-01
2. Press [INC] or [DEC] to switch the setting to ON or OFF.
*
To enable transmission, set this to ON.
This button is disabled when Tx Mode is set to Mode 2.
Selecting Sounds on an External
MIDI Device
To switch the tones of an external MIDI device, enter the program
number and the MSB/LSB of the Bank Select message as numerical
values on the RD-300SX.
For instructions on connecting the external devices, refer to
“Connecting the RD-300SX to External Equipment” (p. 12).
MIDI IN Connector
Performance messages from an external MIDI device are received
sounds or switch tones.
1. Press [MIDI Tx].
2. Referring to the following, press the TONE SELECT button
to which the parameter you want to change is assigned,
then select the parameter.
MIDI OUT Connector
If you want to change the sounds, press [ORGAN] first to send
the Program Change message.
MIDI messages are transmitted from this connector to external MIDI
devices. The RD-300SX’s MIDI OUT connector is used for sending
the performance data of the keyboard controller section as well as
data used for saving various settings and patterns (Bulk Dump
→p. 44).
TONE
Indication
Parameter
SELECT
button
PIANO
Bank Select MSB
Bank Select LSB
Program Change
Pan
Connecting to External MIDI Sound
Generators
E.PIANO
ORGAN
fig.04-02
STRINGS/
PAD
MIDI IN
GUITAR/
BASS
Reverb Send
Chorus Send
Key Transpose
MIDI Ch
Sound Generator A
MIDI OUT
RD-300SX
BRASS/
WINDS
VOICE/
SYNTH
RHY/GM2
If the RD-300SX transmits a Program number or a Bank number
for which no Tone has been assigned, an alternate Tone may be
selected, or in some cases, there may be no sound played. If you
do not want to transmit the Program number or Bank Select, set
the MSB/LSB to “--- (OFF).”
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting External MIDI Devices
3. Press [INC] or [DEC] to change the parameter values.
Pressing [INC] and [DEC] simultaneously switches the settings
value to “--- (OFF).” When this setting is “--- (OFF),” program
numbers or bank select messages will not be transmitted.
When recording to an external sequencer, it is convenient if you set
MIDI TX Mode to Mode2. When using this function, you can get the
most suitable settings for recording the RD-300SX’s data to an
external sequencer, without having to make all the Part and channel
settings.
When setting the LOWER zone, set [LOWER SELECT] to ON.
Parameter
Tx
Value
For more detailed information on how to make the settings, refer to
“Setting the MIDI Tx Mode” (p. 46).
Bank Select MSB
Bank Select LSB
Program Change
CC 00
CC 32
Program
Change
0–127, --- (OFF)
0–127, --- (OFF)
0–127, --- (OFF)
Pan
CC10
CC91
CC93
---
L64–0–63R, --- (OFF)
--- (OFF), 0–127
--- (OFF), 0–127
-48–0– +48
Reverb Send
Chorus Send
Key Transpose
MIDI Ch
Use the following procedure when recording to an external
sequencer.
---
1–16
1. Turn on the external sequencer’s Thru function and turn off
the RD-300SX’s local control.
For details, refer to the section “Switching Local Control On
and Off” (p. 46).
Recording RD-300SX
Performances to an
Refer to your sequencer owner’s manual for instructions on
how to carry out this procedure.
External MIDI Sequencer
2. Select the Setup for the performance to be recorded.
For instructions on selecting the Setup, refer to p. 34.
Now, try using an external sequencer to record your music onto
multiple tracks, and then play back the recorded performance.
3. Use the procedure described in the previous section
“Settings for Recording” to make the MIDI Tx Mode settings
to Mode2.
Connecting to an External
Sequencer
4. Begin recording with the external sequencer.
5. Bulk Dump the Setup.
fig.04-03
Transmit the contents of the selected Setup to the external
sequencer.
For instructions on carrying out this operation, refer to
“Transferring Setups to External Devices (Setup Bulk
Dump)” (p. 44).
MIDI IN
MIDI OUT
6. Perform on the RD-300SX.
7. When the performance is finished, stop recording with the
external sequencer.
MIDI Sequencer
MIDI OUT
MIDI IN
Recording is now complete.
RD-300SX
back on the external sequencer.
1. Before starting the connection procedure, make sure that
2. After reading “Connecting the RD-300SX to External
Equipment” (p. 12), connect an audio device/system or
headphones.
3. Connect the external MIDI sequencer with the MIDI cable as
shown in the figure above.
4. As described in “Turning On the Power” (p. 13), turn on the
power of each device.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting External MIDI Devices
Playing the RD-300SX’s
from an External MIDI Device
Transmitting Bank Select (Controller Number 0, 32) and Program
Change messages from the external MIDI device to the RD-300SX
allows you to switch Setups and Tones.
Internal Sound Generator
from an External MIDI Device
Try Playing the RD-300SX from an External MIDI Device.
Making Connections
Switching Tones (p. 19, p. 60)
fig.04-05
Switching Setups
MIDI OUT
The MIDI messages transmitted by the external MIDI device will be
received by the RD-300SX to select Setups as shown in the following
table.
Number
Bank Select
Program Change
Number
MIDI Sequencer
MIDI IN
MSB
LSB
1–32
85
0
1–32
must be matched to the RD-300SX’s controller channel (p. 39).
When switching individual parts, match the MIDI channel of the
transmitting device to the RD-300SX's receive channel. However, if
the same channel is set for both the control channel and receive
channel, the control channel takes priority, resulting in Setups being
RD-300SX
1. Before starting the connection procedure, make sure that
2. After reading “Connecting the RD-300SX to External
Equipment” (p. 12), connect an audio device/system or
headphones.
3. Connect the external MIDI device with the MIDI cable as
shown in the figure above.
4. As described in “Turning the Power On and Off” (p. 13),
turn on the power of each device.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Your Computer via USB (USB Mode)
4. Press [INC] or [DEC] to set the value.
Switching USB Drivers
Display
Value
Original
Description
Select this when using the sup-
plied driver with a USB connec-
tion.
Select this when using a generic
USB driver included with the OS
with a USB connection.
What is the USB MIDI Driver?
Generic
The USB MIDI Driver is a software which passes data between
the RD-300SX and the application (sequencer software, etc.) that
is running on the USB-connected computer.
5. After changing settings, turn the power off and then on
The USB MIDI Driver sends data from the application to the
RD-300SX, and passes data from the RD-300SX to the
again.
application.
fig.05-01
There is no need to use the Write procedure for the USB Driver
settings.
Exchanging MIDI Messages
with Your Computer
You can use a USB connector to connect the RD-300SX to your
computer. For more details, refer to the separate “USB Installation
Guide.”
Application
USB connector
USB
Driver
*
Connecting your computer to the RD-300SX for the first time requires
installation of the “USB Driver” (on the included CD-ROM) to the
computer. For more details, refer to the separate “USB Installation
Guide.”
USB cable
Computer
*
921
*
Only MIDI data can be transmitted using USB.
USB connector
To prevent malfunction and/or damage to speakers or other devices,
always turn down the volume, and turn off the power on all devices
before making any connections.
*
USB cables are not included. Consult your Roland dealer if you need
to purchase.
RD-300SX
*
*
Use a USB cable no longer than 3 meters.
Turn on the power to the RD-300SX before starting up MIDI
applications on the computer. Do not turn the RD-300SX on or off
while any MIDI application is running.
When a computer is connected to the USB connector, you can
determine the USB driver to be used as follows:
*
Do not connect or disconnect the USB cable while the RD-300SX’s
power is on.
1. Press [EDIT].
*
*
If not using USB, disconnect the USB cable from the RD-300SX.
The indicator lights, and the RD-300SX switches to Edit mode.
If, during the transmission/reception of data, the computer switches to
energy-saving mode or suspended mode, or if the RD-300SX’s power
is switched on or off, the computer may freeze, or the RD-300SX’s
operation may become unstable.
2. Press [INC] or [DEC] to select “System,” then press
[ENTER].
fig.disp.SYS
*
When using your computer’s sequencer software to record
RD-300SX performances, we recommend setting the sequencer
software’s Soft Thru to “OFF.”
3. Press [RHY/GM2].
50
Download from Www.Somanuals.com. All Manuals Search And Download.
About V-LINK
V-LINK (
) is a function that provides for the play of
music and visual material. By using V-LINK-compatible video
equipment, visual effects can be easily linked to, and made part of
the expressive elements of a performance.
(Examples)
By using the RD-300SX and Edirol DV-7PR together, you can:
•
Make Edirol DV-7PR playback settings remotely from the RD-
300SX.
•
Use the RD-300SX’s keyboard to switch the Edirol DV-7PR’s
images (clips/palettes).
*
In order to use V-LINK with the RD-300SX and Edirol DV-7PR, you
will need to make connections using an USB-MIDI Interface (sold
separately).
Before connecting this unit to other devices, turn off the power
to all units. This will help prevent malfunctions and/or damage
to speakers or other devices.
How to Use the V-LINK
1. Hold down [SHIFT] and press [SOUND CONTROL].
The display changes as shown below, and the RD-300SX
switches to image control mode.
fig.06-01
You can control images using the twelve keys at the left end of
the keyboard.
fig.06-03
A0~G#1
*
While V-LINK is switched on, no sound is produced when you press
any of the twelve keys at the left end of the keyboard.
2. Hold down [SHIFT] and press [SOUND CONTROL] once
again to exit.
The display returns to its normal state, and the V-LINK setting
is switched off.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If the RD-300SX does not function in the way you expect, first
check the following points. If this does not resolve the
problem, consult your dealer or a nearby Roland Service
Station.
Problem
Check/Solution
Is the device enabled to transmit MIDI
messages?
• Set [MIDI TX] to ON (p. 47). MIDI
messages cannot be transmitted if
[MIDI TX] is set to OFF.
Problem
Check/Solution
No Sound From the
Connected MIDI
Device
Power Not Coming
On
Is the power cord properly connected? (p.
11)
Is the RD-300SX’s keyboard controller
section MIDI Transmit channel matched
to the connected MIDI device’s MIDI
Receive channel?
14) or connected device turned all the
way down?
• Make the Ch settings screen (p. 47).
Are all connections properly made?
• When using the RD-300SX as a stand-
alone instrument, be sure to connect
with audio cables or use headphones
(p. 12).
Is the power to all devices turned on?
No Sound (With a
MIDI Device
Is the MIDI cable connected and plugged
in correctly?
Connected)
Does the MIDI channel match the
connected instrument? (p. 47)
Are sounds audible with headphones
connected?
Is V-LINK switched on (p. 51)?
When V-LINK is switched on, the twelve
keys at the left end of the keyboard are
used to control images, and no sounds
are played with these keys.
• If sounds are audible through
headphones, it may indicate that there
is a short in an audio cable or some sort
of amp or mixer problem. Check the
cables and equipment once again.
No Sound From the
Left Side
With certain Tones, for example Rhythm
Sets, bass Tones, Timpani, and other
Tones will not sound if a portion of the
Tone falls outside the recommended
range.
No Sound
Is a zone level turned off with the ZONE
LEVEL sliders? (p. 24)
No Sound in a
Specific Range
Is the Part setting set to OFF (p. 43)?
If the sound for a pressed key is not being
played, is the Local Switch set to OFF?
• Set the Local Control to ON (p. 46).
The RD-300SX has a maximum
polyphony of 128 voices. When playing
together with a song or Rhythm along
with heavy use of the damper pedal, the
performance data may exceed the
the keyboard may not sound.
Are the effect settings correct?
Not All Sounds Are
Played
• Check the ON/OFF settings for MULTI
EFFECTS [ON/OFF] (p. 28), MFX Zone
(p. 40) and level settings (p. 28).
Has the volume been lowered by pedal
operations or by MIDI messages (volume
messages or expression messages)
Did you call up a Setup?
• When a Setup is called up, the current
Tone, effect, and other settings are
disabled, and the selected Setup goes
settings to a Setup (p. 35).
received from an external MIDI device?
No Sound for
Specific Zone
Is the zone’s volume level turned down?
• Check the ZONE LEVEL sliders (p. 24).
Tones Are Altered
Did you press ONE TOUCH [PIANO]?
• When ONE TOUCH [PIANO] is
pressed, the current Tone, effect, and
other settings are disabled, and settings
for use in piano performances go into
effect (p. 18). Save the required settings
to a Setup (p. 35).
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check/Solution
Problem
Check/Solution
Is the RD-300SX in Dual Play? (p. 21)
Depending on the Tone selected, pitches
played in certain registers will be
Two Sounds are
When the RD-300SX is connected to an
external sequencer, set it to the Local OFF
mode (p. 46). Alternatively, set SOFT
THRU on the sequencer to “OFF.”
changed and played at other pitches.
Produced When the
Keyboard is Played
Have you set Transpose? (p. 25, p. 55)
Has the RD-300SX gone out of tune?
• Check the System Master Tune settings
in Edit mode (p. 38).
Pitch is Odd
Is [MIDI TX] set to ON?
• When [MIDI TX] is set to ON, the
external sound generator is controlled.
To change the RD-300SX’s tones, set
[MIDI TX] to OFF (p. 47).
Has the pitch been changed by pedal
operations or by Pitch Bend messages
received from an external MIDI device?
Tone Doesn’t
Change
Are the LOWER SELECT settings correct?
(p. 28)
When you try playing more than the
maximum 128 voices simultaneously,
sounds currently being played may be
cut out.
Sound is Cut Off
Could the Effect Type be set to 0? (p. 29)
Could the Effect Level be set to 0? (p. 28)
Effects Not Applied/
Effects Sound
Wrong
Sound Keeps
Playing When Key is
Pressed
Is the hold pedal polarity reversed?
• Check the System Damper Pedal
Polarity settings in Edit mode (p. 38).
When the zone to which the effects are
applied is assigned to the Lower Tone,
the effects are then not applied to the
Upper Tone (p. 40).
Is the pedal connected correctly?
• Connect the pedal securely to the
PEDAL jack (p. 12).
As the RD-300SX piano sounds faithfully
reproduce the depth and reverberation of
actual acoustic pianos, reverberation may
still be audible even after the reverb effect
is removed from sounds.
Are you using a pedal made by another
manufacturer?
Reverb Remains
Even After Reverb is
Lifted
• Use the pedal included with the RD-
300SX or an optional DP Series or
similar pedal.
With the acoustic piano settings, sounds
in the upper 1 1/2-octave range are
extended to the end regardless of the
damper pedal actions. The tone is also
different in this range. Roland’s pianos
faithfully reproduce the sonic qualities of
acoustic pianos. Furthermore, you can
use the instrument’s Key Transpose
setting to change that range over which
the damper pedal has no effect.
Pedal Has No Effect,
or Effect “Sticks”
Unplugging a pedal cord from the unit
pedal’s effect to be applied nonstop.
Be sure to switch off the power to the unit
before attempting to disconnect or
connect a pedal cord (p. 12).
Sound Suddenly
Changes at Key in
Upper Octaves
When Setup Pedal Shift is set to ON and
the pedal is being used as a dedicated
Setup switch (p. 39), the control pedal
function cannot be used (p. 40).
In some Tones, the settings are such that
sounds randomly play from the left or
right side (are panned) each time the keys
are pressed. These settings cannot be
changed.
Sounds Come From
Left or Right Each
Time Key is Pressed
(Panned)
Sounds can be distorted due to equalizer,
multi-effect, and Part volume settings.
Adjust the ZONE LEVEL sliders (p. 24).
Sound is Distorted
Is a distortion-type effect being applied to
the sound (p. 28)?
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check/Solution
When listening through headphones:
Certain piano tones that feature
vibrant, sparking sounds contain a
large high-frequency component,
which may make it appear that a
metallic reverberation has been
applied. This faithfully reproduces the
characteristics of acoustic pianos, and
does not indicate any malfunction.
Since this reverberation becomes
particularly audible when
High-Pitched Whine
is Produced
supplemented by heavy reverb, you
may be able to diminish the problem
by reducing the amount of reverb
applied to the sound.
When listening through speakers:
Here, a different cause (such as
resonance produced by the RD-300SX)
would be suspect. Consult your
Roland dealer or nearest Roland
Service Center.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects List
Indicated
number
Effect name
Overview
Effect parameter name when changed by holding down
[MULTI EFFECTS] and pressing [INC] or [DEC] (p. 29):
An overview thereof (Value)
00
01
THRU
EQUALIZER
Amplifies the low and high ends for a notice-
ably striking tone.
EQ Gain:
Gain of the low and high range (0–30)
02
03
04
05
06
07
MID CUT
Cuts the midrange for a clean, refreshing
tone.
Reduces the volume of the low end.
Mid Gain:
Gain of the middle range (0–30)
Low Gain:
Gain of the low range (0–64)
LOW CUT
LOW BOOST
Boosts the volume of the lower range, creat-
ing powerful lows.
This filter cuts specific frequencies.
Boost Gain:
Amount by which the lower range will be boosted (0–12)
Filter Cutoff:
Cutoff frequency of the filter (0–127)
Rate:
Rate of modulation (0–21)
Sens:
Sensitivity of the enhancer (0–127)
NOTCH
FILTER
STEP FILTER
This filter changes the cutoff frequency in a
stepped fashion.
Controls the overtone structure of the high
frequencies, adding sparkle and tightness to
the sound.
ENHANCER
08
AUTO WAH
Cyclically controls a filter to create cyclic
change in timbre.
Manual:
Adjusts the center frequency at which the effect is applied
(0–127)
09
10
11
HUMANIZER
Adds a vowel character to the sound, making
it similar to a human voice.
Simulates the large triple stack speaker
Rate:
Frequency at which the two vowels switch (0–21)
Direct Level:
Volume of the direct sound (0–127)
Rate:
SPEAKER
SIMULATOR
PHASER
This is a stereo phaser.
A phase-shifted sound is added to the origi-
nal sound and modulated.
Frequency of modulation (0–21)
12
13
14
STEP PHASER
This is a stereo phaser.
The phaser effect will be varied gradually.
Extremely high settings of the phase differ-
ence produce a deep phaser effect.
A phaser that continues raising/lowering the
frequency at which the sound is modulated.
Step Rate:
Frequency of modulation (0–21)
Rate:
Frequency of modulation (0–21)
Speed:
Speed at which to raise or lower the frequency at which the
sounds modulated (0–200)
MULTI
PHASER
INFINITE
PHASER
15
RING
MODULATOR
This is an effect that applies amplitude mod-
ulation (AM) to the input signal, producing
bell-like sounds.
Frequency:
Adjusts the frequency at which modulation is applied (0–127)
16
17
18
19
20
STEP RING
MODULATOR
A ring modulator that cyclically changes the
modulated frequencies.
Cyclically modulates the volume to add
tremolo effect to the sound.
Cyclically modulates the stereo location of
the sound.
Cyclically modulates the stereo location of
the sound.
By applying successive cuts to the sound, this
effect turns a conventional sound into a
sound that appears to be played as a backing
phrase. This is especially effective when ap-
plied to sustain-type sounds.
Rate:
Rate of modulation (0–21)
Rate:
Frequency of the change (0–21)
Rate:
Frequency of the change (0–21)
Rate:
Frequency of the change (0–21)
Rate:
TREMOLO
AUTO PAN
STEP PAN
SLICER
Frequency of the change (0–21)
21
22
ROTARY
The Rotary effect simulates the sound of the
rotary speakers often used with the electric
organs of the past.
This type provides modified response for the
rotary speaker, with the low end boosted fur-
ther.
Speed:
Rotational speed of the rotating speaker (0–1)
VK ROTARY
Speed:
Rotational speed of the rotating speaker (0–1)
23
24
CHORUS
This is a stereo chorus.
Depth:
Depth of modulation (0–127)
Depth:
Depth of modulation (0–127)
FLANGER
This is a stereo flanger.It produces a metallic
resonance that rises and falls like a jet air-
plane taking off or landing.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects List
Indicated
number
Effect name
Overview
Effect parameter name when changed by holding down
[MULTI EFFECTS] and pressing [INC] or [DEC] (p. 29):
An overview thereof (Value)
25
26
STEP
FLANGER
HEXA-
CHORUS
This is a flanger in which the flanger pitch
changes in steps.
Uses a six-phase chorus to give richness and
spatial spread to the sound.
Step Rate:
Rate of pitch change (0–21)
Balance:
Volume balance between the direct sound and the chorus
sound (0–100)
27
28
TREMOLO
CHORUS
This is a chorus effect with added Tremolo
(cyclic modulation of volume).
Balance:
Volume balance between the direct sound and the tremolo
chorus sound (0–100)
Balance:
Volume balance between the direct sound and the chorus
sound (0–100)
SPACE-D
This is a multiple chorus that applies two-
phase modulation in stereo. It gives no im-
pression of modulation, but produces a
transparent chorus effect.
29
30
31
32
33
34
3D CHORUS
3D FLANGER
This applies a 3D effect to the chorus sound.
The chorus sound will be positioned 90 de-
grees left and 90 degrees right.
This applies a 3D effect to the flanger sound.
The flanger sound will be positioned 90 de-
grees left and 90 degrees right.
This applies a 3D effect to the step flanger
sound. The flanger sound will be positioned
90 degrees left and 90 degrees right.
A chorus effect that lets you apply an effect
independently to the low-frequency and
high-frequency ranges.
A flanger that lets you apply an effect inde-
pendently to the low-frequency and high-fre-
quency ranges.
A step flanger that lets you apply an effect in-
dependently to the low-frequency and high-
frequency ranges.
Balance:
Volume balance between the direct sound and the chorus
sound (0–100)
Balance:
Volume balance between the direct sound and the flanger
sound (0–100)
Step Rate:
3D STEP
FLANGER
Rate of pitch change (0–21)
2BAND
CHORUS
Balance:
Volume balance of the original sound and chorus sound
(0–100)
Balance:
Volume balance of the original sound and flanger sound
(0–100)
Balance:
2BAND
FLANGER
2BAND STEP
FLANGER
Volume balance of the original sound and flanger sound
(0–100)
35
36
37
38
39
40
41
OVERDRIVE
Creates a soft distortion similar to that pro-
duced by vacuum tube amplifiers.
Produces a more intense distortion than
Overdrive.
This is an overdrive that provides heavy dis-
tortion.
This is a distortion effect that provides heavy
distortion.
This is an effect that simulates the sound of a
guitar amplifier.
Flattens out high levels and boosts low lev-
els, smoothing out fluctuations in volume.
Compresses signals that exceed a specified
volume level, preventing distortion from oc-
curring.
Level:
Output Level (0–127)
Level:
Output Level (0–127)
Level:
Output Level (0–127)
Level:
Output Level (0–127)
Pre Amp Master:
Volume of the entire pre-amp (0–127)
Threshold:
Adjusts the volume at which compression begins (0–127)
Threshold:
Adjusts the volume at which compression begins (0–127)
DISTORTION
VS OVERDRIVE
VS
DISTORTION
GUITAR AMP
SIMULATOR
COMPRESSOR
LIMITER
42
GATE
Cuts the reverb’s delay according to the vol-
ume of the sound sent into the effect. Use this
when you want to create an artificial-sound-
ing decrease in the reverb’s decay.
Threshold:
Volume level at which the gate begins to close (0–127)
43
44
45
46
DELAY
This is a stereo delay.
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
LONG DELAY
SERIAL DELAY
A delay that provides a long delay time.
This delay connects two delay units in series.
Adds modulation to the delayed sound.
MODULATION
DELAY
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects List
Indicated
number
Effect name
Overview
Effect parameter name when changed by holding down
[MULTI EFFECTS] and pressing [INC] or [DEC] (p. 29):
An overview thereof (Value)
47
48
49
50
51
52
53
54
3TAP PAN
DELAY
Produces three delay sounds; center, left and
right.
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
Balance:
Volume balance between the direct sound and the delay sound
(0–100)
4TAP PAN
DELAY
This effect has four delays.
MULTI TAP
DELAY
This effect provides four delays with feed-
back.
REVERSE
DELAY
This is a reverse delay that adds a reversed
and delayed sound to the input sound.
SHUFFLE
DELAY
Adds a shuffle to the delay sound, giving the
sound a bouncy delay effect with a swing
feel.
This applies a 3D effect to the delay sound.
The delay sound will be positioned 90 de-
grees left and 90 degrees right.
3D DELAY
TIMECONTROL
DELAY
A stereo delay in which the delay time can be
varied smoothly.
LONG TIME
CONTROL
DELAY
A delay in which the delay time can be varied
smoothly, and allowing an extended delay to
be produced.
55
56
TAPE ECHO
A virtual tape echo that produces a realistic
tape delay sound.
In addition to a Lo-Fi effect, this adds various
types of noise such as white noise and disc
noise.
Echo Level:
Volume of the echo sound (0–127)
Balance:
Volume balance between the direct sound and the effect sound
(0–100)
LOFI NOISE
57
58
59
60
LOFI
COMPRSSOR
This is an effect that intentionally degrades
the sound quality for creative purposes.
Balance:
Volume balance between the direct sound and the effect sound
(0–100)
Balance:
Volume balance between the direct sound and the effect sound
(0–100)
Balance:
Volume balance between the direct sound and the effect sound
(0–100)
Balance:
Volume balance between the direct sound and the effect sound
(0–100)
LOFI RADIO
TELEPHONE
PHONOGRAPH
In addition to a Lo-Fi effect, this effect also
generates radio noise.
This applies a telephone sound.
Simulates a sound recorded on an analog
record and played back on a record player.
61
62
PITCH
SHIFTER
2VOICE PITCH
SHIFTER
A stereo pitch shifter.
Fine:
Adjusts the pitch of the pitch shifted sound (0–100)
Balance:
Volume balance between the Pitch Shift 1 and Pitch Shift 2
sounds (0–100)
Shifts the pitch of the original sound. This 2-
voice pitch shifter has two pitch shifters, and
can add two pitch shifted sounds to the orig-
inal sound.
63
64
65
STEP PITCH
SHIFTER
REVERB
This pitch shifter changes the shift volume of
the pitch shift sound in a stepped fashion.
Adds reverberation to the sound, simulating
an acoustic space.
This is a special type of reverb in which the
reverberant sound is cut off before its natural
length.
Rate:
Rate of modulation (0–21)
Time:
Time length of reverberation (0–127)
Balance:
Volume balance between the direct sound and the reverb
sound (0–100)
GATED
REVERB
66
67
OVERDRIVE
→CHORUS
This effect connects an overdrive and a cho-
rus in series.
Chorus Balance:
Adjusts the volume balance between the sound that is sent
through the chorus and the sound that is not sent through the
chorus (0–100)
OVERDRIVE
→FLANGER
This effect connects an overdrive and a
flanger in series.
Flanger Balance:
Adjusts the volume balance between the sound that is sent
through the flanger and the sound that is not sent through the
flanger (0–100)
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects List
Indicated
number
Effect name
Overview
Effect parameter name when changed by holding down
[MULTI EFFECTS] and pressing [INC] or [DEC] (p. 29):
An overview thereof (Value)
68
69
70
71
72
73
74
75
76
77
78
OVERDRIVE
→DELAY
This effect connects an overdrive and a delay
in series.
Delay Balance:
Adjusts the volume balance between the sound that is sent
through the delay and the sound that is not sent through the
delay (0–100)
DISTORTION
→CHORUS
This effect connects a distortion and a chorus
in series.
Chorus Balance:
Adjusts the volume balance between the sound that is sent
through the chorus and the sound that is not sent through the
chorus (0–100)
DISTORTION
→FLANGER
This effect connects a distortion and a flanger
in series.
Flanger Balance:
Adjusts the volume balance between the sound that is sent
through the flanger and the sound that is not sent through the
flanger (0–100)
DISTORTION
→DELAY
This effect connects a distortion and a delay
in series.
Delay Balance:
Adjusts the volume balance between the sound that is sent
through the delay and the sound that is not sent through the
delay (0–100)
ENHANCER
→CHORUS
This effect connects an enhancer and a cho-
rus in series.
Chorus Balance:
Adjusts the volume balance between the sound that is sent
through the chorus and the sound that is not sent through the
chorus (0–100)
ENHANCER
→FLANGER
This effect connects an enhancer and a
flanger in series.
Flanger Balance:
Adjusts the volume balance between the sound that is sent
through the flanger and the sound that is not sent through the
flanger (0–100)
ENHANCER
→DELAY
This effect connects an enhancer and a delay
in series.
Delay Balance:
Adjusts the volume balance between the sound that is sent
through the delay and the sound that is not sent through the
delay (0–100)
CHORUS
→DELAY
This effect connects a chorus and a delay in
series.
Delay Balance:
Adjusts the volume balance between the sound that is sent
through the delay and the sound that is not sent through the
delay (0–100)
FLANGER
→DELAY
This effect connects a flanger and a delay in
series.
Delay Balance:
Adjusts the volume balance between the sound that is sent
through the delay and the sound that is not sent through the
delay (0–100)
CHORUS
→FLANGER
This effect connects a chorus and a flanger in
series.
Flanger Balance:
Adjusts the volume balance between the sound that is sent
through the flanger and the sound that is not sent through the
flanger (0–100)
Depth:
Depth of the effect (0–10)
SYMPATHETIC
RESONANCE
On an acoustic piano, holding down the
damper pedal allows other strings to reso-
nate in sympathy with the notes you play,
creating rich and spacious resonances. This
effect simulates these sympathetic resonanc-
es.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
Display
Meaning
Too much MIDI data was sent from the external MIDI instrument at one time,
and the unit could not process the data. Reduce the amount of MIDI data being
sent to the RD-300SX.
A problem such as a loose MIDI cable or computer cable occurred.
Make sure the MIDI cables and computer cables are correctly hooked up.
A system error has occurred.
Try performing the procedure over again. Should this message continue to ap-
pear even after repeated attempts, please consult the nearest Roland Service
Center.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone List
MSB: Bank Select MSB (Control Number: 0)
LSB: Bank Select LSB (Control Number: 32)
PC: Program Change
[PIANO]
[GUITAR/BASS]
<GM2 Tones>
No. Tone Name
MSB LSB PC
No. Tone Name
MSB LSB PC
No. Tone Name
MSB LSB PC
001
002
003
004
005
006
007
008
009
010
X-Ultimate
087
087
087
087
087
087
087
087
087
087
064
064
064
064
064
064
064
064
064
064
001
002
003
004
005
006
007
008
009
010
001
002
003
004
005
006
007
008
009
010
011
012
013
Dyna Nylon
087
087
087
087
087
087
087
087
087
087
087
087
087
068
068
068
068
068
068
068
068
068
068
068
068
068
001
002
003
004
005
006
007
008
009
010
011
012
013
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
071
072
073
074
075
Piano 1
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
000
001
002
000
001
000
001
000
001
000
001
002
003
000
001
002
003
004
000
001
002
003
000
001
000
000
000
000
001
000
001
000
000
001
002
000
000
001
002
003
000
001
002
000
000
001
002
000
001
000
001
000
000
000
001
002
003
000
001
002
003
001
001
001
002
002
003
003
004
004
005
005
005
005
006
006
006
006
006
007
007
007
007
008
008
009
010
011
012
012
013
013
014
015
015
015
016
017
017
017
017
018
018
018
019
020
020
020
021
021
022
022
023
024
025
025
025
025
026
026
026
026
Grand RD
Steel Gtr
Piano 1w
X-Pure Grand
Mellow Piano
X-PureMellow
Piano+Strings
Rock Piano
Jz Gtr Hall
Blusey OD
Punker
European Pf
Piano 2
Piano 2w
SX Ac.Bass
FingerMaster
SX Fretnot
Slap Bass
Bass+RideCym
Punch MG
101 Bass
Piano 3
Piano 3w
Honky-tonk
Honky-tonk
Honky-tonk 2
E.Piano 1
St.Soft EP
FM+SA EP
60's E.Piano
E.Piano 2
Detuned EP 2
St.FM EP
X-Pure Mono
GrandRD Mono
[E.PIANO]
Synth Bass
No. Tone Name
MSB LSB PC
001
002
003
004
005
006
007
008
009
010
Vintage EP 1
Vintage EP 2
70's E.Piano
60's E.Piano
FM E.Piano
Clav
087
087
087
087
087
087
087
087
087
087
065
065
065
065
065
065
065
065
065
065
001
002
003
004
005
006
007
008
009
010
[BRASS/WINDS]
No. Tone Name
MSB LSB PC
EP Legend
EP Phase
Harpsichord
Coupled Hps.
Harpsi.w
001
002
003
004
005
006
007
008
009
010
StackTp Sect
VoyagerBrass
Wood Symphny
Bigband Sax
Soprano Sax
Tenor Sax
087
087
087
087
087
087
087
087
087
087
069
069
069
069
069
069
069
069
069
069
001
002
003
004
005
006
007
008
009
010
Natural Hps.
Vibraphone
Marimba
Harpsi.o
Clav.
Morning Lite
Flute
Pulse Clav
Celesta
Bend SynBrs
Jump For KY
Afro Horns
[ORGAN]
Glockenspiel
Music Box
Vibraphone
Vibraphone w
Marimba
No. Tone Name
MSB LSB PC
001
002
003
004
005
006
007
Zepix Organ
FullDraw Org
X Perc Organ
Gospel Spin
Mellow Bars
Rock Organ
Massive Pipe
087
087
087
087
087
087
087
066
066
066
066
066
066
066
001
002
003
004
005
006
007
[VOICE/SYNTH]
No. Tone Name
MSB LSB PC
Marimba w
Xylophone
Tubular-bell
Church Bell
Carillon
001
002
003
004
005
006
007
008
Jazz Scat
087
087
087
087
087
087
087
087
070
070
070
070
070
070
070
070
001
002
003
004
005
006
007
008
Morning Star
Choir Aahs
Female Aahs
Galactic SX
Saw Lead
Santur
[STRINGS/PAD]
Organ 1
Square Lead
SuperSawSlow
No. Tone Name
MSB LSB PC
Trem. Organ
60's Organ 1
70's E.Organ
Organ 2
001
002
003
004
005
006
007
008
009
010
011
012
SX Strings
Studio Sect.
OrchestraPad
ChmbrStrings
Pizzicato
087
087
087
087
087
087
087
087
087
087
087
087
067
067
067
067
067
067
067
067
067
067
067
067
001
002
003
004
005
006
007
008
009
010
011
012
[RHYTHM/GM2]
No. Tone Name
MSB LSB PC
Chorus Or.2
Perc. Organ
Organ 3
001
002
003
004
005
SX Pop Kit
SX Rock Kit
SX Jazz Kit
SX R&B Kit
SX House Kit
086
086
086
086
086
064
064
064
064
064
001
002
003
004
005
JP Strings
Soft Pad
Church Org.1
Church Org.2
Church Org.3
Reed Organ
Puff Organ
Accordion Fr
Accordion It
Harmonica
Bandoneon
Nylon-str.Gt
Ukulele
Silky Way
Nu Epic Pad
Strings Pad
Flange Dream
InfinitePhsr
<GM2 Rhythm Sets>
No. Tone Name
MSB LSB PC
006
007
008
009
010
011
012
013
014
GM2 STANDARD 120
000
000
000
000
000
000
000
000
000
001
009
017
025
026
033
041
049
057
GM2 ROOM
GM2 POWER
GM2 ELECTRIC
GM2 ANALOG
GM2 JAZZ
120
120
120
120
120
120
Nylon Gt.o
Nylon Gt.2
Steel-str.Gt
12-str.Gt
GM2 BRUSH
GM2 ORCHESTRA 120
GM2 SFX 120
Mandolin
Steel + Body
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone List
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
Jazz Gt.
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
000
001
000
001
002
000
001
002
003
000
001
000
001
002
000
001
000
000
001
000
000
000
000
000
001
002
003
004
000
001
002
003
000
001
000
000
000
000
000
000
001
000
000
001
002
000
000
001
000
000
001
000
001
000
001
000
001
002
003
000
001
000
001
002
000
000
001
000
001
000
027
027
028
028
028
029
029
029
029
030
030
031
031
031
032
032
033
034
034
035
036
037
038
039
039
039
039
039
040
040
040
040
041
041
042
043
044
045
046
047
047
048
049
049
049
050
051
051
052
053
053
054
054
055
055
056
056
056
056
057
057
058
058
058
059
060
060
061
061
062
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
Brass 2
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
001
000
001
002
003
000
001
002
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
001
002
000
001
002
003
004
000
000
000
001
000
000
000
001
000
000
001
000
000
001
000
000
000
000
000
000
000
001
000
000
000
000
001
002
000
000
001
000
000
000
001
000
000
000
062
063
063
063
063
064
064
064
065
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
081
081
082
082
082
082
082
083
084
085
085
086
087
088
088
089
090
090
091
092
092
093
094
095
096
097
098
099
099
100
101
102
103
103
103
104
105
105
106
107
108
108
109
110
111
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
Shanai
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
121
000
000
000
000
000
001
000
001
000
001
000
001
002
000
000
001
002
000
001
000
001
002
003
004
005
000
001
002
003
000
001
002
003
004
005
000
001
002
003
004
005
006
007
008
009
000
001
002
003
004
005
000
001
002
003
112
113
114
115
116
116
117
117
118
118
119
119
119
120
121
121
121
122
122
123
123
123
123
123
123
124
124
124
124
125
125
125
125
125
125
126
126
126
126
126
126
126
126
126
126
127
127
127
127
127
127
128
128
128
128
Pedal Steel
Clean Gt.
Synth Brass1
Pro Brass
Oct SynBrass
Jump Brass
Synth Brass2
SynBrass sfz
Velo Brass 1
Soprano Sax
Alto Sax
Tinkle Bell
Agogo
Chorus Gt.
Mid Tone GTR
Muted Gt.
Steel Drums
Woodblock
Castanets
Taiko
Funk Pop
Funk Gt.2
Concert BD
Melo. Tom 1
Melo. Tom 2
Synth Drum
808 Tom
Elec Perc
Reverse Cym.
Gt.FretNoise
Gt.Cut Noise
String Slap
Breath Noise
Fl.Key Click
Seashore
Rain
Jazz Man
Overdrive Gt
Guitar Pinch
DistortionGt
Feedback Gt.
Dist Rtm GTR
Gt.Harmonics
Gt. Feedback
Acoustic Bs.
Fingered Bs.
Finger Slap
Picked Bass
Fretless Bs.
Slap Bass 1
Slap Bass 2
Synth Bass 1
SynthBass101
Acid Bass
Clavi Bass
Hammer
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
Pan Flute
Bottle Blow
Shakuhachi
Whistle
Thunder
Wind
Ocarina
Stream
Square Wave
MG Square
2600 Sine
Saw Wave
OB2 Saw
Doctor Solo
Natural Lead
SequencedSaw
Syn.Calliope
Chiffer Lead
Charang
Bubble
Bird
Dog
Horse-Gallop
Bird 2
Synth Bass 2
Beef FM Bass
RubberBass 2
Attack Pulse
Violin
Telephone 1
Telephone 2
DoorCreaking
Door
Slow Violin
Viola
Scratch
Wind Chimes
Helicopter
Car-Engine
Car-Stop
Car-Pass
Car-Crash
Siren
Cello
Wire Lead
Solo Vox
Contrabass
Tremolo Str
PizzicatoStr
Harp
5th Saw Wave
Bass & Lead
Delayed Lead
Fantasia
Yang Qin
Timpani
Warm Pad
Sine Pad
Train
Orche str
Jetplane
Orchestra
Polysynth
Space Voice
Itopia
Starship
60s Strings
Slow Strings
Syn.Strings1
Syn.Strings3
Syn.Strings2
Choir Aahs
Chorus Aahs
Voice Oohs
Humming
Burst Noise
Applause
Laughing
Screaming
Punch
Bowed Glass
Metal Pad
Halo Pad
Sweep Pad
Ice Rain
Heart Beat
Footsteps
Gun Shot
Machine Gun
Lasergun
Explosion
Soundtrack
Crystal
SynVox
Syn Mallet
Atmosphere
Brightness
Goblin
Analog Voice
OrchestraHit
Bass Hit
6th Hit
Echo Drops
Echo Bell
Echo Pan
Star Theme
Sitar
Euro Hit
Trumpet
Dark Trumpet
Trombone
Trombone 2
Bright Tb
*
Some tones sound for only one pressed key
(mono tones).
Sitar 2
Banjo
Tuba
Shamisen
Koto
MutedTrumpet
MuteTrumpet2
French Horns
Fr.Horn 2
Taisho Koto
Kalimba
Bagpipe
Brass 1
Fiddle
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Rhythm Set List
*
[EXC]: will not sound simultaneously with other percussion instruments of the same number.
SX Pop Kit
SX Rock Kit
SX Jazz Kit
SX R&B Kit
SX House Kit
21
23
24
26
28
29
31
33
35
36
38
40
41
43
45
47
Rock Kick
Pop Kick
Old Kick
Pop Kick
Analog Kick 1
Rock Kick
Rock CHH1
Rock Snare 1
Finger Snap
707 Claps
Hand Clap 1
Hand Clap 2
Hand Clap 3
Pop PHH
Hand Clap 4
Snare Roll
Old Kick
Old Kick
Jazz Kick 1
Analog Kick 1
Jazz Swish
Jazz Tap 1
Jazz Tap 2
Finger Snap
707 Claps
Hand Clap 1
Hand Clap 2
Hand Clap 3
Pop PHH
Gospel Hand Clap
Snare Roll
Analog Kick 2
TR909 Kick 1
TR909 Kick 2
R&B CHH 2
R&B CHH 3
R&B CHH 4
Finger Snap
707 Claps
Hand Clap 1
Gospel Hand Clap 2
Hand Clap 2
R&B CHH 5
Gospel Hand Clap
Lo-Bit CHH
Analog Kick 1
R&B Kick
R&B Side Stick 1
R&B Snare 1
R&B Snare 2
R&B Snare 3
Sharp Low Tom 6
R&B CHH 1
Sharp Low Tom 5
R&B CHH 1
Dance Kick
Lo-Bit CHH
22
[EXC1]
Analog Kick 1
Hush Kick
Pop CHH 1
Reg. Snare 1
Finger Snap
707 Claps
Hand Clap 1
Hand Clap 2
Hand Clap 3
Pop PHH
Hand Clap 4
Snare Roll
Techno Kick 2
Concert Snare
Snare Roll
Finger Snap
High-Q
[EXC1]
[EXC1]
[EXC1]
25
27
[EXC1]
[EXC1]
[EXC1]
[EXC1]
Slap
Scratch Push
Scratch Pull
Sticks
Square Click
Metro Click
30
32
34
[EXC1]
[EXC1]
[EXC1]
Metro Bell
Old Kick
Hush Kick
Reg.Stick
Pop Kick
Jazz Kick 2
House Kick 1
House Kick 2
R&B Side Stick 1
House Snare 1
House Snare 2
House Snare 3
House Low Tom 1
House CHH
House Low Tom 2
House PHH
Rock Kick
C2
37
39
Rock Side Stick
Rock Snare 1
Snare Ghost
Rock Snare 2
Rock Low Tom Flm
Rock CHH 1
Rock Low Tom
Rock CHH 2
Rock Mid Tom Flm
Rock OHH
Rock Mid Tom
Rock High Tom Flm
Rock Crash Cymbal
Rock HighTom
Pop Ride Cymbal 2
Rock Chinese Cymbal
Rock Ride Bell
Tambourine
Rock Splsh Cymbal
Cha Cha Cowbell
Rock Chinese Cymbal 2
Vibraslap
Jazz Snare Swing
Jazz Snare 1
Pop Snare Swing
Jazz Snare 2
Jazz Low Tom Flm
Pop CHH 1
Jazz Low Tom
Pop CHH 2
Jazz Mid Tom Flm
Pop OHH
Jazz Mid Tom
Jazz High Tom Flm
Jazz Crash Cymbal
Jazz HighTom
Jazz Ride Cymbal 1
Jazz Chinese Cymbal
Jazz Ride Cymbal 2
Tambourine
Pop Splsh Cymbal
Cha Cha Cowbell
Jazz Crash Cymbal 2
Vibraslap
Pop Ride Cymbal 1
Bongo Hi
Reg. Snare
Reg. Snare Ghost
Titan Snare
Reg. Low Tom Flm
Pop CHH 1
Reg. Low Tom
Pop CHH 2
Reg.Mid Tom Flm
Pop OHH
42
44
46
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
Sharp Low Tom 4
R&B OHH
House Mid Tom 1
House OHH
House Mid Tom 2
House High Tom 1
Reg. Mid Tom
Reg. High Tom Flm
Sharp High Tom 3
Sharp High Tom 2
R&B Crash Cymbal
Sharp High Tom 1
Pop Ride Cymbal 1
R&B Chinese Cym
R&B Ride Bell
Tambourine
TR909 Ride
Cha Cha Cowbell
House Crash Cymbal
Vibraslap
Pop Ride Cymbal 2
House Bongo Hi
House Bongo Lo
House Conga Hi
House Conga Mt
House Conga Lo
Timbale Hi
C3 48
50
49
51
Pop Crash Cymbal 1
Reg. High Tom
Pop RideCymbal 1
Pop Chinese Cymbal
Pop Ride Bell
Tambourine
Pop Splash Cymbal
Cha Cha Cowbell
Pop Crash Cymbal 2
Vibraslap
Pop RideCymbal 2
Bongo Hi
Bongo Lo
Conga Mute
Conga Hi
House Crash Cymbal
House High Tom 2
House Ride Cymbal
Reverse Cymbal
House Ride Bell
ShakeTambourine
House Splash Cymbal
House Cowbell
HouseCrash Cymbal
Vibraslap
Pop Ride Cymbal 2
House Bongo Hi
House Bongo Lo
House Conga Hi
House Conga Mt
House Conga Lo
Timbale Hi
52
53
54
56
58
55
57
59
Pop Ride Cymbal 1
Bongo Hi
Bongo Lo
Conga Mute
Conga Hi
Conga Lo
Timbale Hi
Timbale Lo
C4 60
62
61
63
Bongo Lo
Conga Mute
Conga Hi
Conga Lo
Timbale Hi
Timbale Lo
Agogo Bell Hi
Agogo Bell Lo
Shaker 2
64
Conga Lo
Timbale Hi
Timbale Lo
Agogo Bell Hi
Agogo Bell Lo
Shaker 2
65
66
68
70
Timbale Lo
Timbale Lo
Agogo Bell Hi
Agogo Bell Lo
Cabasa
Agogo Bell Hi
Agogo Bell Lo
Shaker 2
Agogo Bell Hi
Agogo Bell Lo
Cabasa
67
69
Shaker 3
Shaker 3
Shaker 3
House Maracas
House Maracas
71
Whistle Short
Whistle Long
Guiro Short
Guiro Long
Claves
Wood Block Hi
Wood Block Lo
Cuica Mute
Cuica Open
Triangle Mt
Triangle Op
Cabasa
Jingle Bell
Wind Chime
Castanets
Surdo Mute
Surdo Open
Cana
Flamenco Timbale Hi
Flamenco Timbale Lo
Flamenco Timbale Flam
Shaker 1
Shaker 2
Bongo Lo Mt
Grit Snare
Jungle Snare 1
Reg.Stick
Titan Snare
Old Kick
Pop Kick
[EXC2]
Whistle Short
Whistle Long
Guiro Short
Guiro Long
Claves
Wood Block Hi
Wood Block Lo
Cuica Mute
Cuica Open
Triangle Mt
Triangle Op
Cabasa
Jingle Bell
Wind Chime
Castanets
Surdo Mute
Surdo Open
Cana
Flamenco Timbale Hi
Flamenco Timbale Lo
Flamenco Timbale Flam
Shaker 1
Shaker 2
Bongo Lo Mt
LoFi Snare
Jungle Snare 1
Rock Side Stick
Rock Snare 2
Old Kick
Pop Kick
Rock Kick
[EXC2]
Whistle Short
Whistle Long
Guiro Short
Guiro Long
Claves
Wood Block Hi
Wood Block Lo
Cuica Mute
Cuica Open
Triangle Mt
Triangle Op
Cabasa
Jingle Bell
Wind Chime
Castanets
Surdo Mute
Surdo Open
Cana
[EXC2]
Whistle Short
Whistle Long
Guiro Short
Guiro Long
House Claves
Wood Block Hi
Wood Block Lo
Hoo Hi
Hoo Lo
Triangle Mt
Triangle Op
Shaker
Jingle Bell
[EXC2]
Whistle Short
Whistle Long
Guiro Short
Guiro Long
House Claves
Wood Block Hi
Wood Block Lo
Hoo Hi
[EXC2]
[EXC2]
[EXC3]
[EXC3]
[EXC2]
[EXC3]
[EXC3]
[EXC2]
[EXC3]
[EXC3]
[EXC2]
[EXC3]
[EXC3]
[EXC2]
[EXC3]
[EXC3]
C5 72
74
73
75
76
77
78
80
82
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
Hoo Lo
79
Electric Triangle Mt [EXC5]
Electric Triangle Op[EXC5]
Shaker
Jingle Bell
Wind Chime
81
83
Wind Chime
Castanets
C6 84
86
85
87
Castanets
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
Surdo Mute
Surdo Open
Tambourine
Tambourine
Cabasa Up
Cabasa Down
Shaker 1
Shaker 2
[EXC6]
[EXC6]
Surdo Mute
Surdo Open
Cana
Flamenco Timbale Hi
Flamenco Timbale Lo
Flamenco Timbale Flam
Shaker 1
Shaker 2
Bongo Lo Mt
LoFi Snare
Jungle Snare 1
R&B Side Stick 2
Analog Snare
TR808 Kick 1
TR808 Kick 2
Jungle Kick
[EXC6]
[EXC6]
88
Flamenco Timbale Hi
Flamenco Timbale Lo
Flamenco Timbale Flam
Shaker 1
89
90
92
94
91
93
Shaker 2
Bongo Lo Mt
Jazz Snare 1
Jazz Snare 2
Jazz Snare Swing
Jazz Swish
Old Kick
Jazz Kick 1
Jazz Kick 2
Analog Kick 1
Jazz Tap 1
Jazz Tap 2
Pop Snare Swing
Slappy
Wah Gtr Noise 1
Wah Gtr Noise 2
Bongo Lo Mt
Grit Snare
95
Jungle Snare 1
R&B Side Stick 2
Analog Snare
HipHop Kick
TR808 Kick 1
TR808 Kick 2
Techno Kick
Rock Snare Dry
Electric Snare
Jungle Snare 2
Vinyl Noise
96
98
C7
97
99
100
101
Rock Kick
102
104
106
Analog Kick 1
Rock Snare Dry
Electric Snare
Reg. Snare Ghost
Slappy
Analog Kick 1
Rock Snare Dry
Electric Snare
Rock Snare Ghost
Slappy
Techno Kick
103
105
Rock Snare Dry
Electric Snare
Jungle Snare 2
Slappy
Wah Gtr Noise 1
Wah Gtr Noise 2
107
108
Wah Gtr Noise 1
Wah Gtr Noise 2
Wah Gtr Noise 1
Wah Gtr Noise 2
Wah Gtr Noise 1
Wah Gtr Noise 2
C8
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Rhythm Set List
*
*
-----: No sound.
[EXC]: will not sound simultaneously with other percussion instruments of the same number.
GM2 STANDARD
GM2 ROOM
GM2 POWER
GM2 ELECTRIC
21
23
24
26
28
29
31
33
35
36
38
40
41
43
45
47
-----
-----
-----
-----
-----
-----
High-Q
Slap
-----
-----
-----
-----
-----
-----
High-Q
Slap
ScratchPush
ScratchPull
Sticks
SquareClick
Mtrnm.Click
Mtrnm. Bell
Mix Kick
Standard KK1
Side Stick
Standard SN2
909 HandClap
Elec Snare 7
Room Tom 5
Close HiHat2
Room Tom 6
Pedal HiHat2
Room Tom 2
Open HiHat2
Room Tom 2
Rock Tom 1
Crash Cym.1
Rock Tom 1
Ride Cymbal
ChinaCymbal
Ride Bell
Tambourine
Splash Cym.
Cowbell
Crash Cym.2
Vibraslap
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
-----
-----
-----
-----
-----
-----
High-Q
Slap
-----
-----
-----
-----
-----
-----
High-Q
Slap
22
25
27
ScratchPush
ScratchPull
Sticks
SquareClick
Mtrnm.Click
Mtrnm. Bell
Jazz Kick 1
Mix Kick
Side Stick
Standard SN1
909 HandClap
Elec Snare 3
Real Tom 6
Close HiHat2
Real Tom 6
Pedal HiHat2
Real Tom 4
Open HiHat2
Real Tom 4
Real Tom 1
Crash Cym.1
Real Tom 1
Ride Cymbal
ChinaCymbal
Ride Bell
Tambourine
Splash Cym.
Cowbell
Crash Cym.2
Vibraslap
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
[EXC7]
[EXC7]
[EXC7]
[EXC7]
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
30
32
34
SquareClick
Mtrnm.Click
Mtrnm. Bell
Standard KK1
Power Kick1
Side Stick
Dance Snare1
909 HandClap
Elec Snare 4
Room Tom 5
Close HiHat2
Room Tom 6
Pedal HiHat2
Room Tom 2
Open HiHat2
Room Tom 2
Rock Tom 1
Crash Cym.1
Rock Tom 1
Ride Cymbal
ChinaCymbal
Ride Bell
Tambourine
Splash Cym.
Cowbell
Crash Cym.2
Vibraslap
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
SquareClick
Mtrnm.Click
Mtrnm. Bell
Power Kick1
Elec Kick 1
Side Stick
Elec. Snare
909 HandClap
Elec Snare 2
Synth Drum 2
Close HiHat2
Synth Drum 2
Pedal HiHat2
Synth Drum 2
Open HiHat2
Synth Drum 2
Synth Drum 2
Crash Cym.1
Synth Drum 2
Ride Cymbal
ReverseCymbl
Ride Bell
Tambourine
Splash Cym.
Cowbell
Crash Cym.2
Vibraslap
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
C2
37
39
42
44
46
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
C3 48
50
49
51
52
53
54
56
58
55
57
59
C4 60
62
61
63
64
65
66
68
70
67
Agogo
Cabasa
Maracas
Agogo
Cabasa
Maracas
Agogo
Cabasa
Maracas
Agogo
Cabasa
Maracas
69
71
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
C5 72
74
73
75
76
77
78
80
82
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
79
81
83
C6 84
86
85
87
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
88
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Rhythm Set List
*
*
-----: No sound.
[EXC]: will not sound simultaneously with other percussion instruments of the same number.
GM2 ANALOG
GM2 JAZZ
GM2 BRUSH
GM2 ORCHSTRA
GM2 SFX
21
23
24
26
28
29
31
33
35
36
38
40
41
43
45
47
-----
-----
-----
-----
-----
-----
High-Q
Slap
-----
-----
-----
-----
-----
-----
High-Q
Slap
-----
-----
-----
-----
-----
-----
High-Q
Slap
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
22
25
27
Close HiHat2
Pedal HiHat2
Open HiHat2
Ride Cymbal3
Sticks
SquareClick
Mtrnm.Click
Mtrnm. Bell
Concert BD
Mix Kick
Side Stick
Concert Snr
Castanets
Concert Snr
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Timpani
Tambourine
Splash Cym.
Cowbell
Con.Cymbal2
Vibraslap
Concert Cym.
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
[EXC1]
[EXC1]
[EXC1]
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
30
32
34
SquareClick
Mtrnm.Click
Mtrnm. Bell
TR-808 Kick2
TR-808 Kick
808 Rimshot
808 Snare 1
909 HandClap
Elec Snare 6
808 Tom 2
TR-808 CHH
808 Tom 2
808__chh
808 Tom 2
TR-808 OHH
808 Tom 2
808 Tom 2
808 Crash
808 Tom 2
Ride Cymbal
ChinaCymbal
Ride Bell
Tambourine
Splash Cym.
808cowbe
Crash Cym.2
Vibraslap
Ride Cymbal4
Bongo High
Bongo Lo
808 Conga
808 Conga
808 Conga
High Timbale
Low Timbale
Agogo
SquareClick
Mtrnm.Click
Mtrnm. Bell
Jazz Kick 2
Jazz Kick 1
Side Stick
Standard SN3
909 HandClap
Elec Snare 5
Real Tom 6
Close HiHat2
Real Tom 6
Pedal HiHat2
Real Tom 4
Open HiHat2
Real Tom 4
Real Tom 1
Crash Cym.1
Real Tom 1
Ride Cymbal
ChinaCymbal
Ride Bell 3
Tambourine
Splash Cym.
Cowbell
SquareClick
Mtrnm.Click
Mtrnm. Bell
Jazz Kick 2
Jazz Kick 1
Side Stick
Brush Swirl
Brush Slap1
Brush Swirl
Brash Tom 2
Close HiHat3
Brash Tom 2
Pedal HiHat3
Brash Tom 2
Open HiHat3
Brash Tom 2
Brash Tom 2
Crash Cym.3
Brash Tom 2
Ride Cymbal2
ChinaCymbal
Ride Bell 2
Tambourine
Splash Cym.
Cowbell
C2
37
39
-----
-----
High-Q
Slap
ScratchPush
ScratchPull
Sticks
[EXC7]
[EXC7]
42
44
46
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
[EXC1]
SquareClick
Mtrnm.Click
Mtrnm. Bell
Gt.FretNoiz
Gt.CutNoise
Gt.CutNoise
String Slap
Fl.KeyClick
Laughing
Screaming
Punch
Heart Beat
Footsteps
Footsteps
Applause
Creaking
Door
Scratch
Wind Chimes
Car-Engine
Car-Stop
Car-Pass
Car-Crash
Siren
C3 48
50
49
51
52
53
54
56
58
55
57
Crash Cym.2
Vibraslap
Crash Cym.2
Vibraslap
59
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
Ride Cymbal4
Bongo High
Bongo Lo
Mute H.Conga
Conga Hi Opn
Conga Lo Opn
High Timbale
Low Timbale
Agogo
C4 60
62
61
63
64
65
66
68
70
67
Agogo
Cabasa
Agogo
Cabasa
Maracas
Agogo
Cabasa
Maracas
Agogo
Cabasa
Maracas
Train
69
Jetplane
Helicopter
Starship
Gun Shot
Machine Gun
Lasergun
Explosion
Dog
HorseGallop
Bird
Rain
Thunder
Wind
Seashore
Stream
Bubble
-----
808marac
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
808clave
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
71
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
-----
[EXC2]
[EXC2]
[EXC3]
[EXC3]
ShrtWhistle
LongWhistle
Short Guiro
Long Guiro
Claves
Woodblock
Woodblock
Mute Cuica
Open Cuica
MuteTriangl
OpenTriangl
Shaker
Jingle Bell
Bell Tree
Castanets
Mute Surdo
Open Surdo
Applause
[EXC2]
[EXC2]
[EXC3]
[EXC3]
C5 72
74
73
75
76
77
78
80
82
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
[EXC4]
[EXC4]
[EXC5]
[EXC5]
79
81
83
C6 84
86
85
87
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
[EXC6]
-----
-----
-----
88
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Rhythm Pattern List
No.
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
Rhythm Pattern
R&B Pop 1
R&B Pop 2
R&B 1
066
067
068
069
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
R&B 9
R&B 10
R&B 11
R&B 12
R&B 13
R&B 14
R&B 15
R&B 16
R&B 17
R&B 18
Funk 1
Funk 2
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
Rhumba
Mambo 1
Mambo 2
Merengue
Power Fusion 1
Power Fusion 2
Rock 3
Rock 4
Rock 5
Rock 6
Rock 7
Rock 8
Rock 9
Rock 10
Rock 11
Rock 12
Rock 13
Rock 14
Rock 15
R&B 2
Shuffle Pop 1
Shuffle Pop 2
Latin Pop 1
Latin Pop 2
Jazz Brush 1
Jazz Waltz
Ballad 1
Ballad 2
Rock 1
Rock 2
Back Beat 1
Back Beat 2
Elec Dance 1
Elec Dance 2
Pop 1
Pop 2
Pop 3
Pop 4
8Beat Pop 1
8Beat Pop 2
8Beat Pop 3
8Bt Fusion 1
8Bt Fusion 2
Pop Funk 1
Pop Funk 2
Pop Funk 3
Pop Funk 4
Pop Funk 5
Pop Funk 6
Pop Funk 7
Pop Funk 8
16Beat Pop 1
16Beat Pop 2
16Beat Pop 3
16Bt Fusion 1
16Bt Fusion 2
16Bt Fusion 3
Shuffle Pop 3
Shuffle Pop 4
Shuffle Pop 5
Shuffle Pop 6
Shuffle Pop 7
West Coast
Motown
R&B Pop 3
R&B Pop 4
R&B Pop 5
Back Beat 3
Back Beat 4
Back Beat 5
Back Beat 6
Back Beat 7
Back Beat 8
Back Beat 9
Back Beat 10
R&B 3
Funk 3
8Beat Rock 1
8Beat Rock 2
8Beat Rock 3
16Beat Rock 1
16Beat Rock 2
Ballad 3
Piano Ballad
Rockaballad
Blue Grass
Combo 1
Combo 2
Fast Swing 1
Fast Swing 2
Swing 1
Swing 2
Swing 3
Jazz Brush 2
Free Jazz
Jazz 1
Jazz 2
Jazz 3
Jazz 4
Jazz 5
Jazz 6
Jazz 7
Jazz 8
Jazz 9
Jazz 10
Blues 1
Blues 2
Gospel 1
Gospel 2
Polka 1
Rock 16
Rock 17
Rock 18
Rock 19
Rock 20
Progressive
Elec Dance 3
Elec Dance 4
Elec Dance 5
Elec Dance 6
Elec Dance 7
Elec Dance 8
Elec Dance 9
Elec Dance 10
Acid Jazz
Techno
Hip Hop
House
Jungle
Dance
Pop Waltz 1
Pop Waltz 2
Pop Waltz 3
Pop Waltz 4
Simple Waltz 1
Simple Waltz 2
3/4 Brush
5/4 Fusion
5/4 Swing
5/8 Progress
6/4 Fusion
6/8 Progress
6/8 Swing
7/4 Fusion
7/4 Swing
7/8 Progress
Polka 2
Latin Pop 3
Latin Pop 4
Latin Pop 5
Latin Pop 6
Latin Pop 7
Latin Pop 8
Latin Pop 9
Latin Pop 10
Latin Pop 11
Bossa Nova 1
Bossa Nova 2
Bossa Nova 3
Fast Bossa
Pop Bossa
Salsa 1
R&B 4
R&B 5
R&B 6
R&B 7
Salsa 2
Samba 1
Samba 2
R&B 8
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup List
Selecting Stored Settings ([SETUP]) (p. 34)
“RHY:”
These Setups let you enjoy performing with a session-like feel while playing a Rhythm.
Be sure to check it out. For more on Rhythms, refer to Playing Rhythm ([RHYTHM]) (p. 32).
[PIANO]
[STRINGS/PAD]
S.41 Phaser Pad
[VOICE/SYNTH]
S.71 RHY:Trance
S.72 Large Choir
S.73 RHY:Piano/EP
S.74 Humanizer
S.11 Piano&Pad 1
S.12 RHY:Jazz Trio1
S.13 Bright Pad
S.14 3D Effect
S.42 RHY:Bigband
S.43 Strings&Winds
S.44 RHY:Swing Vibe
[E.PIANO]
[GUITAR/BASS]
S.51 RHY: Rock
S.52 Synth Brass
S.53 RHY:Jazz Trio3
S.54 Warm Pad
[RHY/GM2]
S.21 RHY:Jazz Trio2
S.22 Harpsi/Strings
S.23 RHY:Latin
S.24 Piano&Pad 2
S.81 RD SETUP
S.82 RD SETUP
S.83 RD SETUP
S.84 RD SETUP
[ORGAN]
[BRASS/WINDS]
S.61 Orchestra
S.31 Organ Split
S.32 RHY:Jazz Funk
S.33 Cathedral
S.62 Flute/E.Piano
S.63 RHY:SwingPop
S.64 Comp Piano
S.34 RHY: R&B Groove
*
Setup No. 81–84 (RD SETUP) include the “Basic Setup.” Use this when creating Setups from scratch.
Shortcut List
You can easily change settings for the following functions using a number of related buttons.
*
“[A] + [B]” indicates that you are to hold down [A] and press [B].
What to do
Operation
Page
p. 30
p. 27
p. 41
p. 28
Changing the Sound Controller Type
Changing the Reverb Depth
Changing the Reverb Depth for Each Tone
[SOUND CONTROL] + [INC/DEC]
[REVERB] + [INC/DEC]
[REVERB] + [ZONE LEVEL SLIDER]
[MULTI EFFECTS] + [INC/DEC]
Changing the Amount of Multi-effects Ap-
plied
Changing the Amount of Transposition
p. 25
[TRANSPOSE] + [INC/DEC]
[TRANSPOSE] + Key
Changing Rhythm Patterns
p. 32
p. 33
p. 23
[RHYTHM] + [INC/DEC]
Changing the Rhythm Pattern Volume Level
Changing the Split Point Key
[RHYTHM] + [ZONE LEVEL SLIDER]
[SPLIT] + [INC/DEC]
[SPLIT] + Key
Switching V-LINK On and Off
Changing the Reverb Type
Changing the Multi-effects Type
Switching MIDI TX On and Off
Changing the Rhythm Tempo
Changing the Key Touch
p. 51
p. 27
p. 29
p. 47
p. 33
p. 26
[SHIFT] + [SOUND CONTROL]
[SHIFT] + [REVERB]
[SHIFT] + [MULTI EFFECTS]
[SHIFT] + [MIDI TX]
[SHIFT] + [RHYTHM]
[SHIFT] + [LOWER SELECT]
66
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI Implementation Chart
DIGITAL PIANO
Date : Oct. 20, 2004
Version : 1.00
Model RD-300SX
MIDI Implementation Chart
Transmitted
Recognized
Remarks
Function...
Basic
Channel
Default
Changed
1
1
1–16
1–16
–16
Default
Messages
Altered
Mode 3
x
Mode 3
Mode 3, 4(M=1)
* 1
Mode
**************
Note
Number :
0–127
**************
0–127
0–127
True Voice
Note ON
Note OFF
O
x
O
x
Velocity
8n v=64
After
Touch
Key’s
Ch’s
x
x
O
O
Pitch Bend
O
O
0, 32
1
Bank select
Modulation
Portamento time
Data entry
O
O
x
O
O
5
O
6, 38
7
x
O
Volume
O
O
O
O
x
O
10
11
64
65
66
67
71
72
73
74
75
76
77
78
84
91
93
Panpot
O
Expression
Hold 1
O
O
Portamento
Sostenuto
O
O
O
x
O
Control
Change
Soft
O
Resonance
Release time
Attack time
Cutoff
O
x
O
x
O
x
O
Decay time
Vibrato rate
Vibrato depth
Vibrato delay
Portamento control
Effect1 depth
Effect3 depth
NRPN LSB, MSB
RPN LSB, MSB
x
O
x
O
x
O
x
O
x
O
O
O
x
O (Reverb)
O (Chorus)
98, 99
100, 101
x
x
O
Prog
Change
0–127
**************
O
0–127
: True Number
Program number 1–128
System Exclusive
O
O
: Song Pos
: Song Sel
: Tune
x
x
x
x
x
x
System
Common
System
Real Time
: Clock
: Commands
x
x
x
x
x
x
x
x
O
x
O (120, 126, 127)
: All sound off
O
:
Reset all controllers
Aux
Message
x
: Local Control
: All Notes OFF
: Active Sense
: Reset
O (123–125)
O
x
* 1 Recognized as M=1 even if M≠1.
Notes
Mode 1 : OMNI ON, POLY
Mode 2 : OMNI ON, MONO
O : Yes
X : No
Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF, MONO
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
RD-300SX: Digital Piano (Conforms to General MIDI 2 System)
● Keyboard
● Dimensions
88 keys (Compact Progressive Hammer Action Keyboard)
1,408 (W) x 336 (D) x 134 (H) mm
55-7/16 (W) x 13-1/4 (D) x 5-5/16 (H) inches
● Part
● Weight
16 Parts
15.5 kg / 34 lbs 3 oz
● Maximum Polyphony
● Accessories
128 voices
Owner’s Manual
● Wave Memory
USB Installation guide
CD-ROM (Roland Digital USB Driver)
Damper Pedal (DP-8)
AC Adaptor (PSB-1U)
Power Cord
64 M bytes (16-bit linear equivalent)
● Tones
Normal Tones:
70
256
5
General MIDI 2 Tones:
Rhythm Sets:
● Options
General MIDI 2 Rhythm Sets:
9
Keyboard Stand: KS-12
Pedal Switch:
Damper Pedal:
Foot Switch:
DP-2
● Setups
DP-8
32
BOSS FS-5U,
FS-6 (TRS phone jacks cannot be used.)
● Effects
Expression Pedal: EV-5, EV-7
MIDI Implementation
Multi-Effects:
78 types
4 types
Reverb:
Sound Control
2-band Digital Equalizer
962a
*
In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
● Rhythm Pattern
185 styles
● Controllers
Zone Level slider x 2
Equalizer knobs
Pitch Bend/Modulation lever
● Display
7 segments, 3 characters (LED)
● Connectors
Headphones Jack: Stereo 1/4 inch phone type
Output Jacks (L/MONO, R): 1/4 inch phone type
Pedal Jacks (DAMPER, CONTROL): 1/4 inch TRS phone type
MIDI Connectors (IN, OUT)
USB Connector (MIDI)
DC IN Jack
● Power Supply
DC 9 V (AC adaptor)
● Power Consumption
11 W
68
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Attack Time .................................................................... 41
Fine Tune ........................................................................ 42
B
Bend Range .................................................................... 42
Bulk Dump
Ground Terminal ........................................................... 10
C
Connecting
Pedals ........................................................................ 12
Power Cord .............................................................. 11
D
Damper Pedal Switch ................................................... 43
DC In jack ....................................................................... 10
Decay Time ..................................................................... 41
M
Modulation Lever ...................................................... 9, 30
Depth ......................................................................... 28
Rotary Effect ............................................................. 29
Type ........................................................................... 29
E
Edit
Tone Parameter ........................................................ 41
Utility ......................................................................... 44
Zone Parameter ........................................................ 42
Effects List ...................................................................... 55
ENTER .............................................................................. 9
EQUALIZER .............................................................. 9, 31
Error Messages .............................................................. 59
EXIT ................................................................................... 9
O
ONE TOUCH ................................................................... 9
OUTPUT R/L(MONO) Jacks ...................................... 10
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
P
Part ............................................................................ 16, 43
Pitch ........................................................................... 30, 38
Pitch Bend Lever ............................................................. 9
Polarity
Tempo
TONE SELECT Buttons .................................................. 9
Tonic ................................................................................ 38
R
Restoring ......................................................................... 45
Reverb Effect
USB Driver ................................................................ 39, 50
USB Mode ....................................................................... 50
RHYTHM ................................................................... 9, 32
Rhythm
WRITE ......................................................................... 9, 35
S
Single Mode ................................................................... 20
SOUND CONTROL .................................................. 9, 30
Sound Generator Section .............................................. 16
SPLIT ........................................................................... 9, 22
Split Mode ................................................................ 20, 22
Split Point ....................................................................... 23
Stretch Tune ................................................................... 38
System ............................................................................. 37
70
Download from Www.Somanuals.com. All Manuals Search And Download.
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
For EU Countries
This product complies with the requirements of European Directive 89/336/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
RD-300SX
Digital Piano
Roland Corporation U.S.
5100 S. Eastern Avenue, Los Angeles, CA 90040-2938, U. S. A.
(323) 890 3700
Telephone :
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
COSTA RICA
TRINIDAD
NORWAY
JORDAN
AFRICA
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
JUAN Bansbach Instrumentos
Musicales
AMR Ltd
Roland Scandinavia Avd.
AMMAN Trading Agency
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
Ground Floor
Kontor Norge
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: (02) 899 9801
KUWAIT
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 2273 0074
SINGAPORE
SWEE LEE MUSIC
COMPANY PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
CURACAO
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
REUNION
TEL: 243-6399
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 16-
5857
Beirut, LEBANON
TEL: (01) 20-1441
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
PORTUGAL
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
CRISTOFORI MUSIC PTE LTD
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
That Other Music Shop(PTY)Ltd.
11 Melle St., Braamfontein,
Johannesbourg,
SOUTH AFRICA
TEL: (011) 403 4105
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
OMAN
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TALENTZ CENTRE L.L.C.
P.O. BOX 37, MUSCAT,
POSTAL CODE 113
TEL: 931-3705
FAX: (011) 403 1234
EUROPE
TEL:(593-4)2302364
TEL: (02) 2561 3339
TEL: (266) 364 609
Paul Bothner(PTY)Ltd.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
QATAR
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
THAILAND
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
TEL: (021) 674 4030
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
VIETNAM
Saigon Music
Suite DP-8
40 Ba Huyen Thanh Quan Street
Hochiminh City, VIETNAM
TEL: (08) 930-1969
TEL: 262-0788
SPAIN
ASIA
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
GUATEMALA
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
SWEDEN
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
TEL:(502) 599-2888
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
AUSTRALIA/
NEW ZEALAND
TEL: (014) 575811
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
AUSTRALIA/
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
TEL: (2) 666 10529
TEL: (010) 6426-5050
TEL: (011) 223-5384
DENMARK
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
TURKEY
Ant Muzik Aletleri Ithalat Ve
Ihracat Ltd Sti
Siraselviler Caddesi
Siraselviler Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2449624
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
CENTRAL/LATIN
AMERICA
UNITED KINGDOM
MEXICO
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
TEL: 2415 0911
TEL: (04) 3360715
UNITED KINGDOM
TEL: (01792) 702701
TEL: (55) 5668-6699
Parsons Music Ltd.
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
NORTH AMERICA
MIDDLE EAST
BARBADOS
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way
Richmond B. C., V6V 2M4
CANADA
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: (505)277-2557
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
PANAMA
TEL: (604) 270 6626
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE
PANAMA
TEL: 17 211 005
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
TEL: 315-0101
TEL: (23) 511011
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
TEL: (022) 66-9426
TEL: (905) 362 9707
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
IRAN
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
U. S. A.
KOREA
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
TEL: (021) 285-4169
TEL: (323) 890 3700
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
TEL: (574)3812529
Lima - Peru
TEL: (511) 4461388
As of January 15, 2005 (ROLAND)
03785945
’05-5-3N
Download from Www.Somanuals.com. All Manuals Search And Download.
|