®
®
c a r a u d i ofor
f a n a t i c s
2-Channel Amplifiers
Operation & Installation
®
Download from Www.Somanuals.com. All Manuals Search And Download.
S
– ii –
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear Customer,
Congratulations on your purchase of the world's finest brand of car audio amplifiers.
At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are
pleased you choseour product. Through years ofengineeringexpertise, hand craftsman-
ship and critical testing procedures, we have created a wide range of products that
reproduce music with all the clarity and richness you deserve.
For maximum performance we recommend you have your new Rockford Fosgate
product installed by an Authorized Rockford Fosgate Dealer, as we provide specialized
training through Rockford Technical Training Institute (RTTI). Please read your
warranty and retain your receipt and original carton for possible future use.
Great product and competent installations are only a piece of the puzzle when it comes
to your system. Make sure that your installer is using 100% authentic installation
accessories from Connecting Punch in your installation. Connecting Punch has
everything from RCA cables and speaker wire to Power line and battery connectors.
Insist on it! After all, your new system deserves nothing but the best.
To add the finishing touch to your new Rockford Fosgate image order your Rockford
wearables, which include everything from T-shirts and jackets to hats and sunglasses.
To get a free brochure on Rockford Fosgate products and Rockford accessories, in the
U.S. call 602-967-3565 or FAX 602-967-8132. For all other countries, call +001-602-
967-3565 or FAX +001-602-967-8132.
PRACTICE SAFE SOUND™
CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dB
MAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUND
SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER
130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.
If, after readin g your m an ual, you still h ave question s regardin g th is product,
we recom m en d th at you see your Rockford Fosgate dealer. If you n eed furth er
assistan ce, you can call us direct at 1-800-669-9899. Be sure to h ave your serial
n um ber, m odel n um ber an d date of purch ase available wh en you call.
Th e serial n um ber can be foun d on th e outside of th e box. Please record it in
th e space provided below as your perm an en t record. Th is will serve as
verification of your factory warran ty an d m ay becom e useful in recoverin g your
am plifier if it is ever stolen .
Serial Num ber: ________________________________
Model Num ber: ________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
T
ABL E O F
C
O N T E N T S
Specifications .............................................................................................. i
Introduction................................................................................................ 1
Punch Amplifier Accessory Pack ................................................................... 1
2-Channel Feature Chart .............................................................................. 2
Design Features .......................................................................................... 4
Installation Considerations ........................................................................... 6
Mounting Location ...................................................................................... 7
Battery and Charging .................................................................................. 8
Wiring the System ....................................................................................... 8
Using Passive Crossovers ........................................................................... 10
Table of Component Values........................................................................ 11
Installation ............................................................................................... 12
System Diagrams...................................................................................... 18
Troubleshooting ........................................................................................ 21
Dynamic Power Measurements................................................................... 23
Warranty Information ................................................................................ 25
International Information ............................................................................ 26
GETTING STARTED
Welcome to Rockford Fosgate! This manual is designed to provide information
for the owner, salesperson and installer. For those of you who want quick
information on how to install this product, please turn to the Installation
Section of this manual or refer to the icons listed below. Other information can
be located by using the Table of Contents. We, at Rockford Fosgate, have
worked very hard to make sure all the information in this manual is current. But,
as we are constantly finding new ways to improve our product, this information
is subject to change without notice.
I
N
S
T
A
L
L
A
T
I
®
®
TROUBLE-
S
H
O
O
T
I
a
d
v
a
n
c
e
d
O
p
e
r
a
t
i
o
n
N
G
O
N
Sections marked
INSTALLATION
include “slam dunk”
wiring connections
Sections marked
TROUBLESHOOTING
include recommendations for
curing installation problems
Sections marked
ADVANCED OPERATION
include in-depth
technical information
Download from Www.Somanuals.com. All Manuals Search And Download.
I
N T R O D U C T I O N
Rockford engineers designed the Punch 2-channel amplifiers to withstand
the rugged automotive environment while delivering superior sound quality
in a flexible, reliable, and efficient package. TRANS•ANA is a low voltage
circuit in the preamp stage of all Punch amplifiers that lets the music sound
crystal clear and very real, even when played at high volume levels. This is
matched with TOPAZ, a unique grounding circuit used to eliminate noise
problems associated with car audio systems and their installation. Flexibility
is accomplished with the use of a built-in crossover. The use of a protection
circuit called NOMAD, along with MOSFET and DSM (Discrete Surface
Mount) technologies improve amplifier efficiency. The result of these
components give the Punch amplifier awesome sound quality in a “Bullet
Proof” package. An explanation of these technologies, most of which are
exclusively designed and patented by Rockford, are described in the
Technical Design Features.
P
UNCH AM PLIFIER ACCESSO RY
P
ACK
The accessory pack shipped with the Punch 2-channel amplifiers includes
the mounting hardware necessary to secure the amp to the vehicle and to
attach the end caps to the amplifier.
Installation & Operation Manual
Punch Verification Certificate
(4) Amplifier mounting screws (#8 x 3/4" Phillips)
(1) ATC Inline Fuseholder
(1) ATC 15 Amp Fuse (Punch 100)
(1) ATC 20 Amp Fuse (Punch 150)
(1) ATC 30 Amp Fuse (Punch 250)
(1) ATC 40 Amp Fuse (Punch 360)
(1) AGU 50 Amp Fuse (Punch 500)
Note: Refer to the Specification section of this manual for recommended
Punch 800 fuse sizes.
– 1 –
Download from Www.Somanuals.com. All Manuals Search And Download.
PUNCH 2-CHANNEL AMPLIFIER FEATURE CHART
100
2
150
2
250
2
360
2
500
800
# of CHANNELS
2
2
RMS Power Mono (4Ω)
RMS Power Mono (2Ω)
RMS Power Bridged/Mono (4Ω)
Stable Into: (each channel)
Stable into: (bridged/mono)
25x2
50x2
100x1
2Ω
37.5x2
70x2
140x1
2Ω
62.5x2
125x2
250x1
2Ω
90x2
180x2
360x1
2Ω
125x2 200x2
250x2 400x2
500x1 800x1
2Ω
2Ω
4Ω
4Ω
4Ω
4Ω
4Ω
4Ω
1
CIRCUITRY
TRANS•ana – circuit topology
TRANS•nova – patented circuit topology2
Class-G – high efficiency topology
MEHSA – heat dissipating technology
TOPAZ– patented noise eliminating circuitry3
DSM – discrete surface mount
MOSFETS – power supply & output devices
NOMAD – protection circuit
x
–
–
–
x
x
x
x
x
–
–
x
x
x
x
x
x
–
–
x
x
x
x
x
x
–
–
x
x
x
x
x
x
–
–
x
x
x
x
x
x
–
–
x
x
x
x
x
FEATURES
Die Cast Heatsink4
x
x
x
–
–
–
x
–
–
x
x
x
–
–
–
x
–
–
x
x
x
–
–
–
–
x
–
x
x
x
–
–
–
–
x
–
x
x
x
–
–
–
–
x
–
x
x
x
–
–
–
–
x
–
Hi-Level Inputs – for factory radios
RCA Inputs – for aftermarket radios
Balanced Inputs
Input Switches – eliminates “Y” adaptors
Pass-Thru – feeds signal to aux. amp
Pwr/Spk Screw Terminals
Pwr/Spk Block Terminals
4 Gauge Pwr/Gnd
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
100
150
250
360
500
800
Adjustable Punch Bass
x
–
–
–
–
–
(0dB/+6dB/+12dB @ 45Hz)
Variable Punch Bass
–
x
x
–
x
–
x
–
x
–
(0dB ~+18dB @ 45Hz)
Adjustable Xover (80Hz)
HP/FULL/LP5 HP/FULL/LP5
Variable Xover (50Hz ~ 210Hz)
Crossover Slope (Butterworth)
–
–
HP/FULL/LP5 HP/FULL/LP5 HP/FULL/LP5 HP/FULL/LP5
12dB
12dB
12dB
-
12dB
-
12dB
-
12dB
-
Phase Warp (00 ~ 1800)
-
-
GENERAL
B+ Fuse Size
15A ATC 20A ATC 30A ATC
40A ATC 50A ATC 60A ATC
Dimensions (H x W x L)
2.60" x
9.60" x
6.70"
2.60" x
9.60" x
6.70"
2.60" x
9.60" x
7.70"
2.60" x
9.60" x
8.70"
2.60" x
9.60" x
9.70"
2.60" x
9.60" x
14.70"
(6.60cm x (6.60cm x (6.60cm x (6.60cm x (6.60cm x (6.60cm x
24.38cm x 24.38cm x 24.38cm x 24.38cm x 24.38cm x 24.38cmx
17.01cm) 17.01cm) 19.55cm)
22.04cm) 24.63cm) 37.33cm)
--INTERNAL USE ONLY--
Heatsink Type
#1
#1
#2
#3
#4
#6
1
Additional information on features, specifications and system designs can be
2
3
4
5
6
Trans•nova is patented under U.S. Patent 4,467,288
TOPAZ is patented under U.S. Patent 5,751,823
Diecast Heatsink is patent pending is patented under U.S. patent # D401,225
HP = 12dB/octave High-Pass / LP = 12dB/octave Low-Pass / FULL = Full Range
Recommended fuse not supplied with amplifier
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
D
ESIGN FEATURES
1
2
9
8
4
7
6
5
3
Punch 100
R+ L+
R– L–
LED
0dB
+6dB
+12dB
HP–Full–LP
80Hz
Crossover
REM
Gain
Left
Input
Right
Input
High
Level
Input
Punch
Bass
R+ L+
L–
R–
B+
GND
+
–
+
–
Left
Right
9
8
4
7
6
5
3
2
1
Punch 150
R+ L+
LED
R– L–
HP–Full–LP
80Hz
Crossover
REM
Left
Input
Right
Input
Punch
Bass
Gain
High
Level
Input
R+ L+
L–
R–
B+
GND
+
–
+
–
Left
Right
Punch 250 / Punch 360 / Punch 500
2
9
3
1
LED
REM
B+
GND
2
7
8
6
4
6
5
8
2
Hz
210
50
190
145
R+ L+
55
HP–Full–LP
R– L–
110
65
Crossover
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
Speaker
R
L–
R–
+
L
–
+
–
9
3
1
2
Punch 800
LED
REM
B+
GND
5
2
9
6
4
6
8
2
7
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
65
Crossover
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
High
Level
Input
R+ L+
Speaker
L
Speaker
R
L–
R–
+
–
+
–
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punch
amplifier dissipates heat generated by the amplifier's circuitry. The
inherent advantage of casting provides a 30% improvement of cooling
over conventional extrusion heatsink designs.
2. Speaker/Power Terminals – These gold-plated connectors are used for
the connection of speaker and power wire and are immune to corrosion
that can cause signal degradation. The Punch 100 and Punch 150
utilize a barrier strip that will accept #10 spade lugs or bare speaker and
power wires sized from 10-18 AWG. The Punch 250, Punch 360,
Punch 500, and Punch 800 utilize heavy duty terminal block connec-
tors that will accept bare wires size from 8-18AWG.
3. REM Terminal – This spade terminal is used to remotely turn-on and
turn-off the amplifier when +12V DC is applied.
4. RCA Input Jacks – The industry standard RCA jack provides an easy
connection for signal level input. They are gold-plated to resist the signal
degradation caused by corrosion.
5. High Level Inputs – The high level inputs use a detachable connector
terminated with 20 AWG leads. These inputs should be used if the source
unit has only speaker line (high level) outputs and not RCA outputs.
6. Gain Control – The input gain control is preset to match the output of
most source units. They can be adjusted to match output levels from a
variety of source units.
7. Punch Bass – The Punch Bass helps correct for acoustical deficiencies
in the listening environment. The Punch Bass allows a narrow band
adjustmentat45Hztohelpreproducefullrangesoundwithoutexcessive
boost. The Punch 100 utilizes a switch that is adjustable at 0dB/+6dB/
+12dB increments. The Punch 150, Punch 250, Punch 360, Punch
500, and Punch 800 utilize a control that is variable from 0dB to
+18dB.
8. InternalCrossover–Theinternalcrossoverisusedtodelegatea specific
range of frequencies to the speaker system for optimum performance.
The crossover can perform three functions: High-Pass (HP), Low-Pass
(LP), or Full Range (FULL). The Punch 100 and Punch 150 utilize a
12dB/octave Butterworth crossover fixed at 80Hz. The Punch 250,
Punch 360, Punch 500, and Punch 800 utilize a 12dB/octave
Butterworth crossover variable from 50Hz to 210Hz.
9. LED Power Indicator – The LED illuminates when the unit is turned on.
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
N STALLATI O N
C
O N SI D ERATI O N S
The following is a list of tools you will need for installing the Punch amplifier:
Allen wrenches 9/64" & 3/32" (included)
Wire strippers
Electric hand drill w/assorted bits
17' (518.16cm) Red Power Wire
12' (365.76cm) Remote Turn-On Wire
1.5' (45.72cm) Black Grounding Wire
Voltmeter
Battery post wrench
Wire cutters
Assorted connectors
Wire crimpers
This section focuses on some of the vehicle considerations for installing your
new Punch amplifier. Checking your battery and present sound system, as
well as pre-planning your system layout and best wiring routes will save
installation time. When deciding how to lay out your new system, be sure that
each component will be easily accessible for making adjustments.
Before beginning any installation, be sure to follow these simple rules:
1. Be sure to carefully read and understand the instructions before attempt-
ing to install the amplifier.
2. For safety, disconnect the negative lead from the battery prior to
beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting your
amplifier in place.
4. Route all of the RCA cables close together and away from any high
current wires.
5. Use high quality connectors for a reliable installation and to minimize
signal or power loss.
6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel
lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle.
7. Never run wires underneath the vehicle. Running the wires inside the
vehicle provides the best protection.
8. Avoid running wires over or through sharp edges. Use rubber or plastic
grommets to protect any wires routed through metal, especially the
firewall.
9. ALWAYS protect the battery and electrical system from damage with
proper fusing. Install a fuseholder and appropriate fuse on the +12V
power wire within 18” (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paint from the
metal to ensure a good, clean ground connection. Grounding connec-
tions should be as short as possible and always be connected to metal
that is welded to the main body, or chassis, of the vehicle.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
M
O UNTING LO CATIO N
The mounting location and position of your amplifier will have a great effect
on its ability to dissipate the heat generated during normal operation. The
design of our cast aluminum heatsink serves to easily dissipate the heat
generated over a wide range of operating conditions. However, to maximize
the performance of your amplifier, care should be taken to ensure adequate
ventilation.
Trunk Mounting
Mounting the amplifier vertically on a surface with the fin grooves running
up and down will provide the best cooling of the amplifier.
Mounting the amplifier on the floor of the trunk will work but provides less
cooling capability than vertical mounting.
Mounting the amplifier upside down to the rear deck of the trunk will not
provide proper cooling and will severely affect the performance of the
amplifier and is strongly not recommended.
Passenger Compartment Mounting
Mounting the amplifier in the passenger compartment will work as long as
you provide a sufficient amount of air for the amplifier to cool itself. If you
are going to mount the amplifier under the seat of the vehicle, you must have
at least 1" (2.54cm) of air gap around the amplifier's heatsink.
Mounting the amplifier with less than 1" (2.54cm) of air gap around the
amplifier's heatsink in the passenger compartment will not provide proper
cooling and will severely affect the performance of the amplifier and is
strongly not recommended.
Engine Compartment Mounting
Rockford Fosgate amplifiers should never be mounted in the engine
compartment. Not only will this void your warranty but could create an
embarrassing situation caused by the ridicule from your friends.
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY AN D
C
H ARG IN G
Amplifiers will put an increased load on the vehicle's battery and charging
system. We recommend checking your alternator and battery condition to
ensure that the electrical system has enough capacity to handle the
increased load of your stereo system. Stock electrical systems which are in
good condition should be able to handle the extra load of any Rockford
amplifier without problems, although battery and alternator life can be
reduced slightly. To maximize the performance of your Rockford Fosgate
amplifier, we suggest the use of a heavy duty battery and an energy storage
capacitor.
W
I RI N G T H E SYST EM
CAUTION: Avoid running power wires near the low level input cables,
antenna, power leads, sensitive equipment or harnesses. The power
wires carry substantial current and could induce noise into the audio
system.
• For safety, disconnect the negative lead from the battery prior to beginning
the installation.
1. Plan the wire routing. Take care when running signal level RCA cables
to keep them close together but isolated from the amplifier's power cables
and any high power auto accessories, especially electric motors. This is
done to prevent coupling the noise from radiated electrical fields into the
audio signal. When feeding the wires through the firewall or any metal
barrier, protect them with plastic or rubber grommets to prevent short
circuits. Leave the wires long at this point to adjust for a precise fit at a
later time.
2. Prepare the Power cable for attachment to the amplifier by stripping 1/
2" of insulation from the end of the wire. Insert the bared wire into the B+
terminal and tighten the set screw to secure the cable in place.
NOTE: The B+ cable MUST be fused 18" or less from the vehicle's
battery. Install the fuseholder under the hood and prepare the cable
ends as stated above. Connections should be
water tight.
Cut
here
X
Trim the power cable within 18" of the battery and
strip 1/2" of insulation from the end of the wire. Cut
the wire loop that is attached to the fuseholder in
half and splice the fuse into the power line using
appropriate inline connectors. Use the section of
cable that was trimmed earlier and connect it to the
other end of the fuseholder.
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Strip 1/2" from the battery end of the power cable and crimp a large ring
terminal to the cable. Use the ring terminal to connect to the battery
positive terminal. Do not install the fuse at this time.
4. Prepare the Ground cable for attachment to the amplifier by stripping 1/
2" of insulation from the end of the wire. Insert the bared wire into the GND
terminal and tighten the set screw to secure the cable in place. Prepare
the chassis ground by scraping any paint from the metal surface and
thoroughly clean the area of all dirt and grease. Strip the other end of the
wire and attach a ring connector. Fasten the cable to the chassis using a
non-anodized screw and a star washer.
5. Prepare the REM turn-on wire for connection to the amplifier by stripping
1/2" of insulation from the wire end. Insert the bared wire into the REM
terminal and tighten the set screw to secure the cable into place. Connect
the other end of the REM wire to a switched 12 volt positive source. The
switched voltage is usually taken from the source unit's auto antenna or
the accessory lead. If the source unit does not have these outputs
available, the recommended solution is to wire a mechanical switch in
line with a 12 volt source to activate the amplifier.
6. Securely mount the amplifier to the vehicle or amp rack. Be careful not
to mount the amplifier on cardboard or plastic panels. Doing so may
enable the screws to pull out from the panel due to road vibration or
sudden vehicle stops.
7. Connect the source signal to the amplifier by plugging the RCA cables/
high level inputs into the input jacks at the amplifier.
8. Connect the speakers. Strip the speaker wires 1/2" and insert into the
speaker terminal and tighten the set screw to secure into place. Be sure
to maintain proper speaker polarity. DO NOT chassis ground any of the
speaker leads as unstable operation may result.
9. Perform a final check of the completed system wiring to ensure that all
connections are accurate. Check all power and ground connections for
frayed wires and loose connections which could cause problems.
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
a
d
v
a
n
c
e
d
O
p
e
r
a
t
USING PASSIVE CROSSOVERS
i
o
n
A passive crossover is a circuit that uses capacitors and/or coils and is placed
on speaker leads between the amplifier and speaker. The crossover delegates
a specific range of frequencies to the speaker for optimum driver performance.
A crossover network can perform one of three functions: High-Pass (capaci-
tors), Low-Pass (inductors or coils) and Bandpass (combination of capacitor
and coil).
The most commonly used passive crossover networks are 6dB/octave
systems. These are easy to construct and require one component per filter.
Placing this filter in series with the circuit will reduce power to the speaker by
6dB/octave above or below the crossover point depending on whether it is a
high-pass or low-pass filter. More complex systems such as 12dB/octave or
18dB/octave can cause impedance problems if not professionally designed.
Passive crossovers are directly dependent upon the speaker's impedance and
component value for accuracy. When passive crossover components are
used in multiple speaker systems, the crossover's effect on the overall
impedance should be taken into consideration along with the speaker's
impedance when determining amplifier loads. CAUTION: The Punch ampli-
fiers are not recommended for impedance loads below 2Ωstereo and 4Ω
bridged (mono) loads.
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
a
d
v
a
n
c
e
d
O
p
e
r
a
t
TABLE OF CROSSOVER COMPONENT VALUES
i
o
n
C
L
6dB/Octave Low-Pass
6dB/Octave High-Pass
Speaker Impedance
Freq.
Hertz
2 OHMS
8 OHMS
4 OHMS
C
L
C
L
C
L
80
100
130
4.1mH
3.1mH
2.4mH
1000µF
800µF
600µF
8.2mH
6.2mH
4.7mH
500µF
400µF
300µF
16mH
12mH
10mH
250µF
200µF
150µF
200
260
400
1.6mH
1.2mH
.8mH
400µF
300µF
200µF
3.3mH
2.4mH
1.6mH
200µF
150µF
100µF
6.8mH
4.7mH
3.3mH
100µF
75µF
50µF
600
800
1000
.5mH
.41mH
.31mH
136µF
100µF
78µF
1.0mH
.82mH
.62mH
68µF
50µF
39µF
2.0mH
1.6mH
1.2mH
33µF
26µF
20µF
1200
1800
4000
.25mH
.16mH
.08mH
66µF
44µF
20µF
.51mH
.33mH
.16mH
33µF
22µF
10µF
1.0mH
.68mH
.33mH
16µF
10µF
5µF
6000
9000
12000
51µH
34µH
25µH
14µF
9.5µF
6.6µF
.10mH
68µH
51µH
6.8µF
4.7µF
3.3µF
.20mH
.15mH
100µH
3.3µF
2.2µF
1.6µF
L = Low-Pass (Inductor)
C = High-Pass (Capacitor)
For more information, see your Authorized Rockford Fosgate Dealer.
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
I
N STALLATIO N
Power Connections
Punch 100 / Punch 150
R+ L+
LED
R– L–
0dB
+6dB
+12dB
HP–Full–LP
80Hz
Crossover
REM
Gain
Left
Input
Right
Input
High
Level
Input
Punch
Bass
R+ L+
R– L–
B+
GND
+
–
+
–
Left
Right
Connect to remote
turn-on lead of
source unit
Connect to chassis
ground of vehicle*
P100
- 15A
P
150
- 20A
Less than 18"
Connect to B+ of battery with
appropriate fuse value
*Keep grounds as short as possible
Power Connections
Punch 250 / Punch 360 / Punch 500
LED
REM
B+
GND
Connect to remote
turn-on lead of
source unit
Connect to chassis
ground of vehicle*
P
250
- 30A
- 40A
P360
P500
–
50A
Less than 18"
Connect to B+ of battery
with appropriate fuse
*Keep grounds as short as possible
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
Power Connections
Punch 800
LED
REM
B+
GND
Connect to remote
turn-on lead of
source unit
P
800
- 60A1
–
Connect to chassis
ground of vehicle*
+
Less than 18"
Optional Energy
Storage Capacitor
Connect to B+ of battery
with appropriate fuse
*Keep grounds as short as possible
1 Fuse not supplied with amplifier
RCA Inputs
High Level Inputs
R
AUD
SEL
CLOCK
AUT
O
IL
L
UM
TUNE
VOL
PWR
D.SCN
SCAN
2
RPT
3
RDM
4
DIM
PAUSE
6
1
5
®
®
[L+]
[L-]
White
White/Black
[R+]Gray
[R-] Gray/Black
use these or these
High
Level
Inputs
RCA Inputs
Hz
50
210
190
145
110
R+ L+
55
R– L–
HP–Full–LP
65
Crossover
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
High
Level
Input
R+ L+
Speaker
L
Speaker
R
L–
R–
+
–
+
–
High Level
Inputs
R+
L+
L–
R–
•
•
High Level Inputs connect directly to radio's speaker outputs
RCA Inputs connect to radio's RCA preamp outputs
CAUTION: Use only one input configuration. Using both the High Level Inputs &
RCA Inputs may cause undesirable operation.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
Crossover Operation
Hz
80
210
50
190
R+ L+
145
55
R– L–
HP–Full–LP
Crossover
110
65
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
High
Level
Input
R+ L+
Speaker
L
Speaker
R
R– L–
+
–
+
–
2
1
Low-Pass (LP)
Operation
High-Pass (HP)
Operation
Hz
80
Hz
1
2
1
2
210
50
210
50
190
190
145
55
145
55
110
65
110
65
80
HP
–
Full
–
LP
HP
–
Full
–
LP
Crossover Frequency
Crossover Frequency
Crossover
Crossover
+3
+2
+1
0
+3
+2
+1
0
Ap
Ap
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
50
100
200
500
1k
2k
50 55 65 80 110145 210
500
1k
2k
Frequency in Hz
Frequency in Hz
Punch Bass Operation
Hz
80
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
High
Level
Input
R+ L+
L–
Speaker
Speaker
R
R–
+
L
–
+
–
+18
+12
+6
+3
0dB
33Hz 45Hz
67.5Hz
33Hz 45Hz
67.5Hz
Minimum
Flat
Maximum
Boost
•
•
Carefully increase potentiometer to add Punch to your bass frequencies
Exercise caution when increasing Punch Bass. Maximum boost can cause
potential woofer damage caused by overexcursion
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
Stereo Operation
Punch 100 / Punch 150
RCA Input
LED
0dB
+6dB
+12dB
HP–Full–LP
80Hz
Crossover
REM
High Level
Gain
Left
Input
Right
Input
Punch
Bass
+
–
B+
GND
+
–
Input
Left
Output
Right
Output
+
–
–
2Ω min. 2Ω min.
+
• RCA inputs are connected to both left and right channels
• Gain for left and right channels operate independently
• Impedance for each channel should be 2Ω minimum
• Crossover can be set for High-Pass, Low-Pass or Full Range
Stereo Operation
Punch 250 / Punch 360 / Punch 500 / Punch 800
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
L–
R–
+
–
+
–
+
–
–
2Ω min. 2Ω min.
+
• RCA inputs are connected to both left and right channels
• Gain for left and right channels operate independently
• Impedance for each channel should be 2Ω minimum
• Crossover can be set for High-Pass (HP), Low-Pass (LP) or Full Range (FULL)
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
Mono Operation
Punch 100 / Punch 150
RCA Input
LED
0dB
+6dB
+12dB
HP–Full–LP
80Hz
Crossover
REM
High Level
Gain
Left
Input
Right
Input
Punch
Bass
+
–
B+
GND
+
–
Input
Left
Right
Output
Output
+
–
4Ω min.
• RCA inputs are connected to both left and right channels
• Gain for left and right channels are set equally to balance the subwoofer
• Impedance for mono channel should be 4Ω minimum
• Crossover can be set for High-Pass, Low-Pass or Full Range
Mono Operation
Punch 250 / Punch 360 / Punch 500 / Punch 800
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
L–
R–
+
–
+
–
+
–
4Ω min.
• RCA inputs are connected to both left and right channels
• Gain for left and right channels are set equally to balance the subwoofer
• Impedance for mono channel should be 4Ω minimum
• Crossover can be set for High-Pass (HP), Low-Pass (LP) or Full Range (FULL)
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
I
®
®
N
S
T
A
L
L
A
T
I
O
N
Stereo/Mono Operation
Punch 100 / Punch 150
RCA Input
LED
0dB
+6dB
+12dB
HP–Full–LP
80Hz
Crossover
REM
High Level
Gain
Left
Input
Right
Input
Punch
Bass
+
–
B+
GND
+
–
Input
Left
Output
Right
Output
+
–
–
2Ω min.
2Ω min.
+
+
–
4Ω min.
• RCA inputs are connected to both left and right channels
• Gain for left and right channels are set equally to balance the subwoofer
• Impedance for each channel should be 2Ω minimum
• Impedance for mono channel should be 4Ω minimum
• Crossover is set for Full Range
• Passive Crossovers are needed for proper stereo/mono operation
Stereo/Mono Operation
Punch 250 / Punch 360 / Punch 500 / Punch 800
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
R– L–
+
–
+
–
+
–
2Ω min.
2Ω min.
–
+
+
–
4Ω min.
• RCA inputs are connected to both left and right channels
• Gain for left and right channels are set equally to balance the subwoofer
• Impedance for each channel should be 2Ω minimum
• Impedance for mono channel should be 4Ω minimum
• Crossover is set for Full Range
• Passive Crossovers are needed for proper stereo/mono operation
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
SYST EM
D
I AG RAM S
2-Way System
R
AUD
SEL
CLOCK
DSPL
AUTO
IL
L
UM
DISC
AMFM
Ch
P.SCN
LOUD
ST LD RDM RPT
TUNE
PWR
VOL
D.SCN
SCAN
2
RPT
3
RDM
4
DIM
5
PAUSE
6
1
®
Crossover
Crossover
Tweeter
Tweeter
Midrange
Midrange
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
3-Way System
Using single voice coil woofers
R
AUD
SEL
CLO
CK
AUTO
I
L
L
UM
DISC
AMFM
Ch
DSPL
SCAN
P.SCN
PT
L
O
UD
ST LD RDM RPT
TUNE
VOL
PWR
D.SCN
1
R
R
DM
DIM
PAUSE
2
3
4
5
6
®
®
Front
Crossover
Crossover
Rear
Tweeter
Tweeter
Midrange
Midrange
+
+
–
+
–
8Ω
8Ω
–
–
–
+
+
+
+
–
+
–
–
+
8Ω
–
8Ω
8Ω
+
+
+
–
–
–
+
–
4Ω
4Ω
4Ω
4Ω
– 19–
Download from Www.Somanuals.com. All Manuals Search And Download.
3-Way System
Using dual voice coil woofers
R
AUD
SEL
CLOCK
DSPL
AUT
O
IL
L
UM
DISC
AMFM
Ch
P.SCN
RPT
3
LOUD
ST LD RDM RPT
TUNE
VOL
PWR
D.SCN
SCAN
2
RDM
4
DIM
5
P
AUSE
1
6
®
®
Rear
Sub
Front
Crossover
Tweeter
Crossover
24dB/octave HP
Tweeter
Midrange
Midrange
Crossover
Crossover
Tweeter
Tweeter
Power 150 or
Power 200
Mono
Amplifier
Midrange
Midrange
–
–
+
+
–
–
+
+
4Ω x 2
+
–
+ – + –
–
+
+
+
–
4Ω x 2
4Ω x 2
–
+
–
+ – + –
–
–
–
+
+
+
+
4Ω x 2
4Ω x 2
4Ω x 2
– 20–
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-S
H
O
O
T
I
N
G
T
R O U BL E SH O O T I N G
Symptom
Diagnosis
Remedy
Amplifier does not
turn on
(Power LED is off)
VoltageappliedtotheREM Check the alternator, battery, fuse,
terminal of the amplifier is and wiring and repair as necessary.
not between 10.5 and If the voltage is above 15.5 volts,
15.5 volts or there is no have the electrical system inspected
voltage present.
by an authorized car service center.
Voltage to the B+ terminal Check the alternator, battery, fuse,
of the amplifier is not be- and wiring and repair as necessary.
tween10.5 and15.5 volts If the voltage is above 15.5 volts,
or there is no voltage have the electrical system inspected
present.
by an authorized car service center.
Check wiring and repair as neces-
sary.
Amplifier is not properly
grounded.
Amplifier has no
sound
Speaker leads are shorted
toeachotherortothechas-
sis of the vehicle.
Disconnect existing speakers and
test with known working speakers
and wires. If amplifier plays, check
and repair wiring and installation of
speakers as necessary.
(Power LED is on)
Speakers are defective.
Disconnect existing speakers and
test with known working speakers.
If amplifier plays, check and repair
speakers as necessary.
Input gain signal for amplifier
is incorrectly set.
Readjust input gains of amplifier.
Speaker Output
Low or Distorted
Source unit output too low or
source unit has no output.
Check system with known working
source and repair or replace origi-
nal source as needed.
Low battery voltage or large
voltage drops to the amplifier
under load.
Check the alternator, battery, fuse,
and power and ground wiring.
Repair as necessary.
Disconnect input signal to ampli-
fier and turn amplifier on and off. If
noise is eliminated, connect REM
lead of amplifier to source unit with
a delay turn-on module.
Voltage spike from output of
preceding component is en-
tering amplifier through in-
put signal.
Amplifier Noise
(Turn-on Pop)
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-S
H
O
O
T
I
N
G
Symptom
Diagnosis
Remedy
Amplifier Noise
Voltage spike from remote
turn-on lead is entering
through REM input terminal.
Use a different 12 volt source for
REM lead of amplifier (i.e., battery
direct). If noise is eliminated, use a
relay to isolate amplifier from noisy
turn-on output.
(Turn-on Pop)
Noise is radiating into RCA Check connections, run the RCA
Engine Noise
signal cable.
cables on a different route away
from sources of high current.
Bad component in the signal
chain.
Check connections, bypass addi-
tionalcomponents(crossoversand
equalizers) betweenthesourceunit
and the amplifier. Connect one
component at a time to determine
the culprit. Repair or replace com-
ponents as necessary.
Noiseisradiatingintospeaker
cables.
Disconnect existing speakers and
connect a test speaker to the output
terminals of the amplifier. If noise is
gone, reroute the speaker cables
away from sources of high voltage.
Multiple grounds in the
audio system.
Check ground connections and
connect amplifiers, signal proces-
sors, and other components to a
central location or try a different
grounding point on the chassis.
Ground loop between source
unit and antenna.
Check connections, disconnect
antenna from source unit. If noise is
gone, install an antenna ground
loop isolator.
Engine Noise when
using high level
inputs
TOPAZinputcircuitry(inRock-
ford amps) or floating input
circuitry (in non-Rockford
amps) does not have refer-
enceto“chassisground.”This
noise, if any, occurs at the
auxiliary amplifier whose in-
puts are fed from the pass-
thru output of the first amp.
Supply reference ground to the
TOPAZ input circuit (or floating in-
put circuit in non-Rockford amps).
Connect shield of RCA input from
auxiliary amp to chassis ground of
radio. An alternative method is to
connect the RCA shield to the
amplifier's power ground terminal.
• If noise persists, see your Authorized Rockford Fosgate Dealer.
Download from Www.Somanuals–.co2m2. A–ll Manuals Search And Download.
D
YN AM I C
P
O W ER
M
EASU REM EN T S
About the Dynamic Power Measurements
The Audio Graph PowerCube is a test instrument used to measure the output of
an amplifier in accordance with IHF-202 industry standards. The IHF-202
standard is a dynamic power measurement and was developed as a means of
measuring power in a manner that best represents the Real World operation of an
amplifier. Many manufacturers, including Rockford Fosgate, at times will measure
amplifier power into a fixed resistor (4 ohm, 2 ohm). While this method is useful
in some types of evaluation and testing, it is not representative of an amplifier that
is connected to a speaker and playing music.
Music
Music is dynamic; the sound waves are complex and constantly changing. In
order to simulate this, the IHF-202 standard calls for the input signal to the
amplifier to be a 1kHz bursted tone. This signal is input (on for 20 milliseconds)
and reduced 20dB for 480 milliseconds. The signal is gradually increased in level
until the amplifier's output exceeds 1% Total Harmonic Distortion (THD). At 1%
distortion becomes audible, therefore, any power produced above that level is
considered unusable. Many manufacturers represent their amplifiers' output
power in excess of 10% distortion. They use many names for this measurement,
such as Total Maximum Power or Maximum Output Power. This is not indicative
of the actual usable output power.
Listening to Loudspeakers - Not Resistors
A loudspeaker is not a resistor. A resistor's value (resistance measured in ohms)
isfixed. Aloudspeaker'simpedanceisdynamic. Itisconstantlychanginginvalue,
dependent upon the frequency of the input signal. Therefore, measuring power
with the amplifier loaded into a 4 ohm resistor is not the same as measuring power
with the amplifier connected to a 4 ohm speaker. Most people do not listen to
music through a resistor.
A 4 ohm speaker may experience a drop in impedance 4-6 times lower than its
nominal (printed) impedance. A speaker will also create phase shifts in the signal
that is passed through it. These phase shifts happen because a speaker is an
inductor(voicecoil) anda capacitor(complianceofthesurround/spider), aswell
as a resistor (voice coil wire).
To simulate a speaker the Audio Graph PowerCube measures output power into
20 different loads. It tests at 8 ohms, 4 ohms, 2 ohms and 1 ohm. Each of these
impedances is also tested at –60°, –30°, 0°, +30° and +60° phase angles.
These different impedances and phase angles represent the shifts in impedance
and phase that can occur in a typical loudspeaker.
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Cubed
The data acquired in the testing procedure is then graphed in the form of a
3-dimensional cube, hence the name PowerCube.
The Phase Angle is expressed on the horizontal axis, the Output Voltage is
presented on the vertical axis and the Impedance is displayed on the Z axis.
Output Power, in watts, is listed on the left hand side for each impedance at
each phase angle.
Audio Graph – The PowerCube™
MODEL BEING
TESTED
VOLTAGE FROM
BATTERY
x2 = STEREO
MONO = BRIDGED MONO
Amplifier: PUNCH 200.
2
14.4V x 2
Rated Power : 100 W @ 4 Ohms
Serial No:
Owner
:
ROCKFORD CORPORATION
8Ω –60° 85
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
*
–30° 84
0° 84
POWER
IN
50V
30V
30° 84
60° 86
WATTS
{
4Ω –60° 162
*
–30° 157
0° 156
30° 157
60° 162
10V
2Ω –60° 273
*
–30° 258
0° 251
8Ω
4Ω
30° 256
60° 271
2Ω
–60° (Cap)
0°
1Ω
1Ω –60° 390
*
{
(Ind) +60°
{
–30° 356
0° 346
Impedance
PHASE ANGLES
30° 352
60° 390
• Example of a Punch 200.2 PowerCube
What is an Amplifier?
An amplifier by definition is a voltage generating device, recreating the signal
which is input to it identically but with increased volume. It will be connected
to a reactive load (the speaker). The impedance of this load and phase of the
signal passing through the load will vary, dependent upon the frequency of
the input signal (music).
Therefore, a perfect amplifier will be able to maintain the same output voltage
regardlessofloadcharacteristicsandwillnotalterthesignalitisreproducing.
A perfect amplifier when measured by the Audio Graph PowerCube would
present data that forms a perfect cube. Unfortunately, amplifiers are not
perfect. The laws of physics generally prevent it. A great amplifier is about the
best one can hope to attain.
As you can see by the PowerCube and as you will experience by listening,
your Punch amplifier is a GREAT AMPLIFIER!
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED
W
AR R AN T Y
I
N FO R M AT I O N
Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following
terms:
•
Length of Warranty
3 years on electronics
2 years on source units
1 year on speakers
90 days on electronic B-stock (receipt required)
90 days on speaker B-stock (receipt required)
•
What is Covered
This warranty applies only to Rockford Fosgate products sold to consumers by Authorized
Rockford Fosgate Dealers in the United States of America or its possessions. Product
purchased by consumers from an Authorized Rockford Fosgate Dealer in another country
are covered only by that country’s Distributor and not by Rockford Corporation.
•
Who is Covered
This warranty covers only the original purchaser of Rockford product purchased from an
Authorized Rockford Fosgate Dealer in the United States. In order to receive service, the
purchaser must provide Rockford with a copy of the receipt stating the customer name,
dealer name, product purchased and date of purchase.
•
•
Products found to be defective during the warranty period will be repaired or replaced
(with a product deemed to be equivalent) at Rockford's discretion.
What is Not Covered
1. Damage caused by accident, abuse, improper operations, water, theft
2. Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate
Service Center
4. Any product which has had the serial number defaced, altered, or removed
5. Subsequent damage to other components
6. Any product purchased outside the U.S.
7. Any product not purchased from an Authorized Rockford Fosgate Dealer
•
•
Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and merchantability are
limited in duration to the period of the express warranty set forth above. Some states do not
allow limitations on the length of an implied warranty, so this limitation may not apply. No
person is authorized to assume for Rockford Fosgate any other liability in connection with
the sale of the product.
How to Obtain Service
Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA#
(Return Authorization number) to return any product to Rockford Fosgate. You are
responsible for shipment of product to Rockford.
Ship to: Speakers
Ship to: Electronics
Rockford Corporation
Warranty Repair Department
2055 E. 5th Street
Rockford Acoustic Design
(Receiving-speakers)
609 Myrtle N.W.
Grand Rapids, MI 49504
RA#:_________________
Tempe, AZ 85281
RA#:_________________
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTALACION DEL
PRODUCTO. EVITARA POSIBLES DAÑOS A VD., AL VEHICULO O AL PRODUCTO.
INTRODUCCION
Los ingenieros de Rockford han diseñado los amplificadores Punch para ofrecer
en el dificil entorno de un automóvil una calidad de sonido superior en un
producto flexible, fiable y eficiente. Trans•ana es un circuito de baja tensión en
la etapa de preamplificación de los amplificadores Punch que permite que la
musica suene limpia y cristalina y muy real, incluso a altos niveles de audicion.
Esto se complementa con el TOPAZ, un circuito exclusivo de masa utilizado
para eliminar los ruidos asociados con las instalaciones de car-audio. La
flexibilidad esta garantizada con el uso de la crossover incorporada. La
fiabilidad se refuerza con el uso de un circuito de proteccion llamado NOMAD,
mientras que los MOSFET y la tecnologia DSM (montaje discreto en superficie)
aumentan la eficiencia del amplificador. La combinacion de todos estos
componentes dan al amplificador Punch una impresionante calidad de sonido
en un chasis discreto. Mas adelante encontrará mas explicaciones de todas
estas tecnologías, la mayoria de ellas usados en exclusiva y patentadas por
Rockford.
UBICACIÓN PARA
EL
MONTAJE
Montaje en el Malatero
Monte el amplificador verticalmente con las lineas del radiador orientadas de
arriba hacia abajo. De esta manera conseguira la mejor ventilacion.
Montaje en el Compartimento de Pasajeros
El montaje en el compartimento de pasajeros sera eficiente en funcion de la
ventilacion que tenga el amplificador. Si va a instalar el amplificador bajo un
asiento deberá dejar al menos 2.5cm libres sobre la carcasa del amplificador.
Instalacion
Por seguridad, desconecte el terminal negativo de la bateria antes de comenzar
la instalacion.
Terminal B+
El cable B+ debe ir provisto de un fusible a una distancia no mayor de 45cm
de la bateria. Prepare el cable e instale el portafusibles en el compartimento del
motor. Las conexiones han de ser impermeables.
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal GND
Prepare un trozo de cable para usarlo como toma de masa. Prepare un
punto de masa en el chasis rascando y eliminando la pintura de la
superficie de metal y limpielo de toda suciedad asegure el cable al chasis
con un tornillo.
Terminal REM
Conecte el cable REM a un punto de +12V con mutable. La señal se suele
coger de la salida auto antena del radio cassette si este no tiene salida
remote.
Funcionamiento Estereo/Mono
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
R– L–
+
–
+
–
+
–
2Ω min.
2Ω min.
–
+
+
–
4Ω min.
• Las entradas RCA se conectan a ambos canales izquierdo y derecho
• Las ganancias izquierda y derecha han de ajustarse igual para ambos
canales
• La impedancia minima para cada canal debe ser 2Ω.
• La impedancia minima mono debe ser 4Ω.
• Crossover en Full Range
• Debe usarse un filtro pasivo para la configuracion estereo/mono
• No llevar a masa ningun cable de altavoz
• Crossovers pasivos se requieren para operar el amplificador en estereo/
mono
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION: Veuillez lire les instructions suivantes pour l'installation de cet
amplifcateur. Ne pas les suivre pourrait causer des blessures ou endommager le
véhicule.
INTRODUCTION
Les ingénieurs de Rockford Fosgate ont conçu l'amplificateur Punch pour
supporter l'environnement rude de l'automobile en délivrant une qualité de son
supérieure dans un ensemble efficace, fiable et flexible. Trans• ana est un circuit
de bas voltage dans l'étage de préamplification de tous les ampificateurs Punch
qui reproduit un son musical clair comme du cristal et très réel, même à très haut
volume. Ceci est accompagné du TOPAZ, un circuit unique employé pour
éliminer les problèmes de bruits parasites associés aux systémes audiomobile
et leur installation. La flexibilité est assurée par l'emploi d'une crossover
incorporée.
La fiabilité est garantie grâce au circuit de protection NOMAD, la technologie
MOSFET et DSM (Composants Montés en Surface) améliorent l'efficacité de
l'amplificateur.
L'ensemble de ces atouts donne à l'amplificateur Punch une qualité de son
inégalable sous une carrosserie “pare-balles.”
Voustrouverezdeplusamplesinformationssurcestechnologies, exclusivement
conçues et brevetées par Rockford, dans la rubrique technique.
MONTAGE
Montage dans le coffre
Monter l'amplificateur verticalement avec les rainures de haut en bas ce qui lui
permet de refroidir plus facilement.
Montage dans l'habitacle
Monter l'amplificateur dans l'habitacle ne pose aucun problème, du moment
qu'il y ait assez d'air pour le refroidir. Si vous montez l'ampli en dessous du
siège, prévoyez 3 cm d'air autour du radiateur.
Installation
Pour votre sécurité, déconnectez la borne négative de la batterie du véhicule
avant de commencer l'installation.
Terminal B+
Il est impératif qu'il y ait un fusible sur le câble pour la connexion à la masse.
Préparez le châssis en grattant la peinture de la surface métallique et nettoyez
la saleté et l'huile. Attachez le câble au châssis avec une vis.
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal GND
Préparezunelongueurdecâblepourla connexionà la masse. Préparezlechâssis
engrattantlapeinturedelasurfacemétalliqueetnettoyezlasaletéetl'huile.Attachez
le câble au châssis avec une vis.
Terminal REM
Connectez le fil REM à une commande 12 volts positive de la source. La
commande12 voltsesthabituellementprisesurla sortieantenneélectrique
de la source ou la commande accessoire. Si la source ne dispose pas de
ces sorties, nous vous recommandons d'installer un interrupteur qui
fournira un positif 12 volts au REM de l'amplificateur.
Opération stéréo/mono (tri
mode)
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
R– L–
+
–
+
–
+
–
2Ω min.
2Ω min.
–
+
+
–
4Ω min.
• Les entrées RCA sont connectées aux canaux gauche et droit
• Les Gains des canaux gauche et droit sont réglés de la même manière
pour équilibrer le subwoofer
• L'impédance de chaque canal devrait être de minimum 2Ω
• L'impédance du canal mono devrait être de minimum 4Ω
• Les crossover sont introduites sur full range
• Il est conseillé d'utiliser les filtres passifs lorsqu'on fait fonctionner
l'amplificateur en tri-mode
• NE connecter AUCUN des câbles HP à la masse au risque d'un
fonctionnement instable
• Des filtres passifs sont nécessaires pour un bon fonctionnement en
mode stéréo/mono
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
BITTE LESEN SIE DIESE GEBRAUCHSANLEITUNG ZUERST SORGFÄLTIG DURCH.
DAS KANN SIE VOR DEM FALSCHEN EINSATZ, AUSFALLEN ODER SOGAR
BESCHÄDIGUNG DES PRODUKTES ODER IHRES FAHRZEUGES SCHÜTZEN.
EINLEITUNG
Rockford Ingenieure haben die Punch Verstärker entwickelt. Mit höchstem
Technologie-Standart, hervorragender Klangqualität, einfacher Handhabung
und bester Servicefreundlichkeit Trans•ana ist eine Nieder-Volt Schaltung im
Vorverstärkerteil aller Punch Verstärker die für kristallklaren Klang auch bei sehr
hohen Lautstärken sorgt. TOPAZ, eine einzigartige Erdungsschaltung verhindert
und unterdrückt Einstreuungen und Störungen die nur allzu oft Car Audio
Systeme beeinträchtigen. Flexibilität durch die Vielfalt der Aktivweiche mit ihren
crossover, lange Lebensdauer durch die Schutzschaltung NOMAD und der
Einsatz von MOSFET Transistoren und DSM (Discrete Surface Mount), machen
diese Verstärker so effizient. Das Ergebnis all dieser Komponenten machen
Punch-Verstärker so einzigartig und in ihrer Klangqualität nahezu unschlagbar.
Eine genauere Beschreibung dieser Technologien, die gröbtenteils einzigartig
und von Rockford patentiert sind, finden Sie unter Technical Design Features.
EINBAUORT
Im Fahrzeugkofferraum
Der vertikale Einbau der Endstufen, das bedeutet, dab die Kühlrippen von oben
nach unten verlaufen, gibt dem Verstärker die beste Kühlung.
Auf der Beifahrerseite
SolltederVerstärkeraufderBeifahrerseitemontiertwerden, soistessehrwichtig,
für eine ausreichende Kühlung zu sorgen. Sollte der Verstärker z.B. unter dem
Beifahrersitz montiert werden, sollte dem Kühlkörper mindestens ein Luftspalt
von 3 cm bleiben, um so für eine ausreichende Kühlung zu sorgen.
Einbau
Zur Sicherheit klemmen Sie den Negativ-Pol der Batterie während des gesamten
Einbaues ab.
B+ Anschluβ
Die Plus-Leitung MUβ ca. 40 cm nach dem Plus-Pol der Batterie abgesichert
sein. Preparieren Si die Kabellängen und montieren Sie den Sicherungshalter im
Motorraum. ALLE Verbindungen müssen wasserdicht sein.
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
GND Anschluβ
Preparieren Sie Ihr Kabel für die Negativ Leitung (Erdung). Preparieren Sie
die Anschlubstelle des Erdungskabels, indem Sie das Metall gründlich
reinigen und vom Lack befreien. Befestigen Sie nun die Erdung an dieser
Stelle mit einer Schraube.
REM Anschluβ
Verbinden Sie das Ein-und Ausschaltungskontroll-Kabel mit Ihrem Radio
(12 Volt positiv). Normalerweise verwenden Sie hierfür die Ant.-Remote
Ihres Radios oder ein eigens dafür vorgesehenes Kabel (Amp-Remote).
Sollte Ihr Radio diesen Anschlub nicht besitzen, so verwenden Sie eine 12
Volt Spannung, die Sie durch einen Schalter ein- und ausschalten können.
Stereo/Mono Operation
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
R– L–
+
–
+
–
+
–
2Ω min.
2Ω min.
–
+
+
–
4Ω min.
• Chinch Eingänge des rechten- und linken-Kanales anschlieben
• Gain -Kontrolle gleich stellen um das Signal des Subwoofer
anzugleichen
• Die Impedanz für jeden Kanal sollte minimum 2 Ohm betragen.
• Die Impedanz des Mono Kanales sollte minimum 4 Ohm betragen
• Die Akltivweichen sollten auf jeden Fall im Stereo/Mono Betrieb
verwendet werden
• Vermeiden Sie auf jeden Fall eine Erdung der Lautsprecher-Kabel, da
sonst ein einwandfreier Betrieb nicht grantiert werden kann
• Passive Frequenzweichen werden für korrekte Stereo/Mono Operationen
benötigt
– 32 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENZIONE:SIPREGADILEGGERELESEGUENTIISTRUZIONIPERL'INSTALLAZIONE
DI QUESTO PRODOTTO. IL NON SEGUIRLE POTREBBE RISULTARE SERIAMENTE
DANNOSO PER LA PERSONA O PER IL VEICOLO.
INTRODUZIONE
Gli ingenieri Rockford hanno progettato la serie di amplificatori Punch per
resistereall'osticoambienteautomobilisticomentresuonanoconuna musicalitá
superiore, offrendo un insieme versatile, affidabile ed efficiente. Trans•ana é un
circuito a bassa tensione dello stadio preamplificatore del Punch che permette
al suono di essere cristallino e reale anche in presenza di volumi molto
elevati…tutto questo é accoppiato TOPAZ, un exclusivo circuito di massa
impiegato per eliminare i problemi di rumore comunemente presenti negli
impianti car audio. Il massimo della versatilitá é raggiunto con l'impiego delle
crossover. L'affidabilitá é completamente garantita dall'impiego di un circuito
diprotezionechiamatoNOMAD, mentrel'usodiMOSFETedella tecnologia DSM
(Discrete Surface Mount) permette di raggiungere efficienze elevatissime. Il
risultato finale di tutte queste tecnnologie moderne é che gli amplificatori Punch
suonano meravigliosamente e sono indistruttibili, a “prova di proiettile.” Una
spiegazione di queste tecnologie innovative, molte coperte da brevetti Rockford,
sono descritte in un'altra sezione di questo manuale.
DOVE POSIZIONARLO
Nel Bagagliaio
Montando l'amplificatore su una superficie in verticale con le alette direzionate
dall'alto verso il basso si garantirá un miglior raffreddamento dell'amplificatore.
Nell'abitacolo
Montare l'amplificatore nell'abitacolo si avrá un funzionamento regolare se si
garantisce un flusso d'aria sufficiente. Per l'installazione sotto un sedile, é
necessario avere uno spazio di almeno 3 cm attorno a tutto l'amplificatore.
Installazione
Per sicurezza, scollegare il polo negativo della batteria dell'auto prima di
iniziare l'installazione.
Terminale B+ (cavo positivo)
Il cavo positivo deve essere protetto da un fusibile a non piú di 45 cm dalla
batteria. Terminare il cavo e installare il fusibile nel vano motore. Tutte le
connessioni devono essere a prova d'acqua.
– 33 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminale GND (cavo negativo)
Deciderela lunghezza delcavoeterminarlo. Prepararela massa grattando
la vernice dal telaio dell'auto ed eliminando tracce di olio o sporco. Fissare
il cavo di massa al telaio con una vite.
Terminale REM (Consenso di accensione)
Collegare il cavo REM ad un positivo presente solo ad autoradio accesa
(normalmente il cavo pilota dell'antenna elettrica o il cavo accessori
dell'autoradio). Se la sorgente non dovesse essere equipaggiata con
queste uscite, la soluzione raccomandabile é di inserire un interruttore su
un cavo positivo e connettersi all'amplificatore.
Stereo/Mono Operation
RCA Input
Hz
210
50
190
145
110
R+ L+
55
R– L–
HP–Full–LP
Crossover
65
80
Right
Gain
Punch Crossover Left
Bass Frequency Gain
Left
Input
Right
Input
R+ L+
High
Level
Input
Speaker
L
Speaker
R
R– L–
+
–
+
–
+
–
2Ω min.
2Ω min.
–
+
+
–
4Ω min.
• Ingressi RCA collegati sia al canale destro sia al sinistro
• Gain (controllo di sensibilitá) regolati in modo identico per bilanciare il
subwoofer
• L'impedenza di ciascun canale deve essere minimo 2Ω
• L'impedenza per il canale mono deve essere minimo 4Ω
• La scheda crossover deve essere in posizione Full Range
• Nel funzionamento Stereo/Mono simultaneo devono essere impiegati i
crossover passivi
• Non cortocircuitare a massa nessun cavo degli altoparlanti, potrebbe
portare ad un funzionamento irregolare
• Crossover passivi sono indispensabili per un corretto funzionamento
stereo/mono
– 34 –
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDCRAFTED IN THE UNITED STATES OF AMERICA
This product is designed, developed and assembled in the USA by a dedicated group of
American workers. The majority of the components used in the construction of this product
are produced by American companies. However, due to the global nature of their
manufacturing facilities and the loudspeaker parts industry in general, some parts may be
manufactured in other countries.
Rockford Fosgate
Rockford Corporation
546 South Rockford Drive
Tempe, Arizona 85281 U.S.A.
In U.S.A., (602) 967-3565
In Europe, Fax (49) 8503-934014
In Japan, Fax (81) 559-79-1265
11/98
E.R.
MAN-2368-B
Download from Www.Somanuals.com. All Manuals Search And Download.
|