DAB / FM RDS / SD Digital Radio
Recorder with PausePlus
Please read this manual before use
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls (Front)
8
9
10
11
12
13
7
6
14
16
5
4
3
2
1
15
1. Preset 5 / Play Mode button
7. PausePlus / Record button
8. On / Off button
12. Select button
2. Preset 4 / Fast-forward button
3. Preset 3 / Rewind button
4. Preset 2 / Stop button
5. Preset 1 / Play / Pause button
6. Loudspeaker
13. Info / Advanced menu button
14. Volume control
15. Band button
9. On / Off indicator
10. LCD display
11. Tuning Up / Down buttons
16. Tone control
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
2
020 8758 0338 (Mon-Fri)
Controls (Rear)
Controls (Left hand side)
18
19
20
21
22
17
19. SD card slot
17. Battery compartment
18. Telescopic aerial
20. Headphone socket
21. Auxiliary input socket
22. DC in socket
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Battery operation
1. Remove the battery cover on the back of the unit by sliding the cover
in the direction of the arrow.
2. Insert four LR20 (D size) batteries into the spaces in the compartment.
Take care to ensure all batteries are inserted with the correct polarity
as shown inside the battery compartment. Replace the battery cover.
3. Reducedpower,yourradioswitchingoffautomatically,anda'stuttering'
sound are all signs that the batteries may need replacing.
1
4. If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
We would recommend for economy that the RecordR is used via the
AC adaptor whenever possible with battery operation for occasional
or standby use only.
IMPORTANT: The batteries should not be exposed to excessive heat
suchassunshine,fireorthelike.Afteruse,disposablebatteriesshould
if possible be taken to a suitable recycling centre. On no account
should batteries be disposed of by incineration.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
4
020 8758 0338 (Mon-Fri)
Using the AC adaptor
1. Place your radio on a flat surface.
2. Fully extend the telescopic aerial. The aerial should be fully extended
and positioned vertically for optimum reception.
3. Insert the adaptor plug into the DC socket located on the left hand side
of your radio. Plug the adaptor into a standard 13 amp mains socket
outlet. The display will show 'Welcome ROBERTS' for a few seconds.
IMPORTANT: The mains adaptor is used as the means of connecting
the radio to the mains supply. The mains socket used for the radio must
remain accessible during normal use. In order to disconnect the radio
from the mains completely, the mains adaptor should be removed from
the mains socket outlet completely.
CharactersappearingontheLCDdisplayindicatethattheradioisconnected
to and powered from the mains supply.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Operating your radio
1. Press the On / Off button to switch on your radio.
When first switched on, the radio will be in DAB mode. After each use
the radio will remember the mode used and then switch on in that
mode the next time that it is used.
1
2. If the radio has been used before, the last used station will be selected.
3. If this is the first time that the radio has been used a quick scan of the
BandIIIDABchannelswillbecarriedout. Duringthescanningprocess
the display will show progress of the station search.The number on
the right of the display is the number of stations that have been found.
4. When the scan is completed the first station (in numeric-alpha order
0....9, A....Z will be selected. The first station in the list of stations
found during scanning will be played. The display will show the station
name.
5. If no signals are found then 'OFF AIR' will be displayed and it may be
necessary to relocate your radio to a position giving better reception.
You should then carry out a scan to find stations as described on page
10.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
6
020 8758 0338 (Mon-Fri)
Selecting a station - DAB
1. Press the On / Off button to switch on your radio.
1
2
2. Press and release the Band button until the DAB mode is selected.
The display will show the name of the radio station currently selected.
3. Press the Tuning Up or Down buttons to step through the list of
available stations.
4. When the desired station name appears on the display, press and
release the Select button to select the station. The display will show
'Tuning' while your radio finds the new station.
5. Adjust the Volume and Tone controls to the required setting.
3
3
Note: If after selecting a station the display shows 'No Service' it may
be necessary to relocate your radio to a position giving better reception.
4
5
5
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Auto-Select - DAB
As an alternative to pressing the select button to select a station your radio
can be set so as to automatically select a station.
1,3
1. Press and hold the Select button until the display shows 'Auto-Select
On'.
2. Press the Tuning Up or Down buttons until the station you require is
visible on the display.After a few seconds your radio will automatically
select the station shown on the display.
2
2
3. To switch off auto-select, press and hold the Select button until the
display shows 'Auto-Select Off'.
Secondary services - DAB
1. Certainradiostationshaveoneormoresecondaryservicesassociated
with them. If a station has a secondary service associated with it then
the secondary service will then appear immediately after the primary
service as you press the Tuning Up button.
1
2. To tune to the secondary service, press and release the Select button.
Mostsecondaryservicesdonotbroadcastcontinuallyandiftheselected
service is not available, the radio will re-tune to the associated primary
service.
2
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
8
020 8758 0338 (Mon-Fri)
Display modes - DAB
Your radio has a range of display options when in DAB mode:-
a
b
c
d
e
f
1. Press and release the Info button to cycle through the various options.
1
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number,
etc.
b. Programme type
c. Time and date
d. Multiplex Name
e. Signal strength
Displays the type of station being
listened to e.g. Pop, Classic, News, etc.
Displays the current time (24 hour format)
and date.
Displays the name of the DAB multiplex
to which the current station belongs.
Displaysagraphshowingthesignalstrength
for the currently tuned DAB station. The
clear unfilled rectangle indicates minimum
signal level required for satisfactory
reception.
f. Frequency & channel
g. Bit rate/audio type
Displaysfrequencyandchannelnumber
for the currently tuned DAB station.
g
Displays the digital bit rate and audio type
for the currently tuned DAB station.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Finding new stations - DAB
As time passes new stations may become available. To find new stations
proceed as follows.
1
1. Press and hold the Info button.
2. Press the Tuning Up or Down buttons until 'Auto Tune' appears on
the display.
3. Press and release the Select button. Your radio will perform a scan
of the Band III DAB channels. As new stations are found, the station
counter on the right-hand side of the display will increase and stations
will be added to the list.
2
2
3
1
Signal strength display - DAB
1. Repeatedly press and release the Info button until the lower line of
the display shows signal strength.
2. Position your radio and try adjusting the aerial as to give maximum
number of black rectangles on the signal strength display. Normally,
the best reception will be found with the aerial fully extended.
3. The clear unfilled rectangle indicates minimum signal level required
for satisfactory reception.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
10
020 8758 0338 (Mon-Fri)
Manual tuning - DAB
Manual tuning allows you to tune your radio to a particular DAB frequency
in Band III. Any new stations found will be added to the station list. This
function can also be used to assist the positioning of the aerial or the radio
to optimise reception for a specific channel or frequency. Note that UK
DAB stations are located in the range of channels 11B to 12D.
1
1. Press and hold the Info button.
2. Press the Tuning Up or Down buttons until the display shows 'Manual
Tune'. Press and release the Select button to enter the manual tuning
mode.
2,3
2,3
3. Press the Tuning Up or Down buttons to select the desired DAB
channel.
2-5
4. Press and release the Select button. The open block in the signal
strength graph shows you the minimum signal strength needed for
good DAB reception. The signal blocks will go up and down showing
the changing signal strength as you adjust the telescopic aerial or
the radio position. Any new radio stations found on the tuned DAB
multiplex will be added to the list stored in the radio.
5. Press and release the Select button to return to the normal tuning
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Dynamic Range Control (DRC) - DAB
Dynamic range control (also known as DRC) can make quieter sounds
easier to hear when your radio is used in a noisy environment.
2
There are three levels of compression:
DRC 0 No compression applied. (default)
DRC 1 Maximum compression applied.
DRC 1/2 Medium compression applied.
3
1. Press the On / Off button to switch on your radio.
2. Press and release the Band button until the DAB band is selected.
3. Press and hold the Info button.
4,5
4,5
4. Press the Tuning Up or Down buttons until 'DRC Value' appears on
the display. Press and release the Select button. The display will show
the current DRC value.
4,6
5. PresstheTuningUporDownbuttonstoselecttherequiredDRCsetting
(default is 0) .
6. Press and release the Select button to confirm the setting. The display
will return to the normal radio display.
Note: Not all DAB broadcasts are able to use the DRC function. If the
broadcast does not support DRC, then the DRC setting in the radio will
have no effect.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
12
020 8758 0338 (Mon-Fri)
Operating your radio - FM Auto Tune
1. Fully extend the telescopic aerial. The aerial should be fully extended
and positioned vertically for optimum reception.
2. Press the On / Off button to switch on your radio.
3
3. Press and release the Band button until the FM band is selected.
4. Press and release the Tuning Up button to cause your radio to search
from low frequency to high frequency and to stop automatically when
it finds a station of sufficient strength.
7
4,6
Note: If your radio does not auto scan, press and release the Select
button until the display shows 'Auto Scan: ON'.
5. After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RDS data present then the radio will display the station name.
6. To find other stations press and release the Tuning Up button as
8
8
before.
7. Press and release the Tuning Down button to cause your radio to
search from high frequency to low frequency and to stop automatically
when it finds a station of sufficient strength. When the end of the
waveband is reached your radio will recommence tuning from the
opposite end of the waveband.
Note:
If you find that FM reception is poor, try repositioning the Telescopic aerial.
Fully extend and position vertically for optimum reception. If you find that
an FM broadcast has a lot of background hiss, this may often be reduced
by setting the radio into Mono reception mode for the current FM station.
Please refer to the section "Stereo / Mono setting - FM" on page 16 for
further details.
8. Adjust the Volume and Tone controls to the required setting.
9. To switch off your radio press the On / Off button.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Manual tuning - FM
1. Fully extend the telescopic aerial. The aerial should be fully extended
and positioned vertically for optimum reception.
2. Press the On / Off button to switch on your radio.
3
4
3. Press and release the Band button until the FM band is selected.
4. Press and release the Select button until the display shows 'Auto
Scan: Off'.
5. Repeatedly press and release the Tuning Up or Down buttons to
tune to a station. The frequency will change in steps of 50kHz.
If the radio is tuned to a station of sufficient signal strength with RDS
information present, then the display may change to show the station
name.
5
5
6. When the waveband end is reached the radio will recommence tuning
from the opposite waveband end.
7. Adjust the Volume and Tone controls to the required setting.
7
8. To switch off your radio press the On / Off button.
7
Note: If you find that FM reception is poor, try repositioning the Telescopic
aerial. Fully extend and position vertically for optimum reception.If you
find that an FM broadcast has a lot of background hiss, this may often
be reduced by setting the radio into Mono reception mode for the current
FM station. Please refer to the section "Stereo / Mono setting - FM" on
page 16 for further details.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
14
020 8758 0338 (Mon-Fri)
Display modes - FM
Your radio has a range of display options for FM mode:-
The Radio Data System (RDS) is a system in which inaudible digital
information is transmitted in addition to the normal FM radio programme.
RDSoffersseveralusefulfeatures.Thefollowingareavailableonyourradio.
1. Press and release the Info button to cycle through the various options.
a
b
c
a. Scrolling text
Displays scrolling text messages such
as artist/track name, phone in number,
etc.
1
b. Programme type
c. Signal strength
Displaystypeofstationbeinglistenedto
e.g. Pop, Classic, News, etc.
Displaysagraphshowingthesignalstrength
for the currently tuned FM station. The
clear unfilled rectangle indicates minimum
signal level required for satisfactory
reception.
d
e
d. Audio mode
Displays the audio mode for the currently
tuned FM station.
e. Time and date
Displays the current time (24 hour format)
and date.
Note: Your radio will display 'Radio Text' if there is no scrolling text and
'Program Type' if there is no programme type information.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Stereo / Mono setting - FM (headphones only)
Your radio will play stereo FM broadcasts in stereo (via headphones)
provided that the received signal is of adequate strength. However, as
a stereo signal becomes weaker the audio signal will become poorer. It
may be preferable to force the radio to play the station in mono in order
to reduce the level of backgound hiss.
3
1. Press the On / Off button to switch on your radio.
2. Tune to the required FM radio station as previously described (see
pages 13, 14).
4,5
3. Press and hold the Info button. The display will show 'FM Audio'.
4. Press and release the Select button. The current audio setting will
5
5
show on the display.
5. Press the Tuning Up or Down buttons until 'Mono' appears on the
display. Press and release the Select button. While this setting is
engaged, the radio will play the current station in mono.
TheMonooverrideisatemporarysettingandisappliedtothecurrently
tuned station only. It is cancelled automatically by tuning to another
radio station.
6. If you wish to cancel the Mono override while listening to the currently
tunedradiostation, followsteps3-5aboveandselect'Auto'.Theradio
will then play the current station in stereo if the signal is sufficiently
strong.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
16
020 8758 0338 (Mon-Fri)
Scan sensitivity setting - FM
Your radio will normally scan for FM broadcasts which are strong enough
to give good reception. However, you may wish the Auto-scan function
to also be able to find weaker signals, possibly from more distant radio
transmitters. Your radio includes a local / distant option for the Auto-scan
function.
2
1. Press the On / Off button to switch on the radio.
2. Press and release the Band button until the FM band is selected.
3. Press and hold the Info button.
3
4. Press the Tuning Up or Down buttons until 'Scan sensitivity' appears
on the display. Press and release the Select button.
4,5
4,5
5. Press the Tuning Up or Down buttons to switch between Local and
Distant options on the lower line of the display. The Distant option will
allow the radio to find weaker signals when scanning.
6. Press and release the Select button to confirm your selection. The
radio will then revert to the normal information display. The Local or
Distant setting is stored in the radio and remains in force until changed
or until a System Reset.
4,6
Note: The initial setting (out of the box, or after a System Reset) causes
the radio to ignore weaker (or more distant) signals.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Presetting stations
You may store your preferred DAB and FM radio stations to the preset
station memories. There are 10 memory presets in your radio, 5 for DAB
and 5 for FM. Presets are remembered by your radio in the event of a
power failure. The procedure for setting presets and using them to tune
stations is the same for FM and DAB modes, and is described below.
1. Press the On / Off button to switch on the radio.
2
2. Press and release the Band button to select the desired waveband.
3. Tune to the required station as previously described.
4. Press and hold the required Preset button 1-5 until the display shows,
for example, 'DAB 1 Preset saved'. The station will be stored under
the chosen preset. Repeat this procedure for the remaining presets.
4
5. Stationswhich havebeenstoredinpresetmemoriesmaybeoverwritten
by following the above procedure.
Recalling a preset station
1. Press the On / Off button to switch on the radio.
2
3
2. Press and release the Band button to select the desired waveband.
3. Press and release the required Preset button 1-5. The display will
show, for example, 'Preset empty' if no station has been stored to that
preset. If a preset has been stored, your radio will tune to the chosen
preset station stored in the preset memory.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
18
020 8758 0338 (Mon-Fri)
Using your radio's PausePlus feature - DAB and FM
How many times has your favourite radio station been interrupted by that
phone call from a double glazing firm or someone selling that must have
item? Sound familiar? With a single press of the PausePlus button you
can put your favourite station on hold while you answer that important call.
AfterthecallorotherimportanttaskisfinishedsimplypressthePausePlus
button to return to your favourite station exactly where you left off so that
you never miss a single word.
1
To use the PausePlus feature you must have an SD or SDHC card
inserted in the radio. Please see 'Using an SD memory card' page 21 for
more information.
Radio stations can effectively be put on hold for up to 60 minutes.
If there is insufficient free space or if the card is write-protected and the
rewind or record function is accessed then a warning message 'Space
Full' or 'SD Protected' will be displayed.
1. Insert an SD card into your radio. Push the card label side facing
towards you and gold contacts first into the card slot on the left hand
side of your radio until it clicks.
To remove the card push the card in so that it clicks once more. It will
then be pushed out slightly allowing removal.
2. Ensure your radio is playing. To use the PausePlus feature simply
press and release the PausePlus button. The radio will start buffering
the currently tuned DAB or FM radio station to the SD card and will
pause the playback. The sound from the loudspeaker will be muted.
The display shows that the radio is in Rewind/Pause mode and also
shows the current paused state. The numbers show the current
playback position in the pause buffer and the total time stored.
1
•
If the radio is paused and the buffer becomes full then the radio will
automatically start to play audio again.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
3. Press and release the PausePlus button a second time to start
playback with the current delay. The display will show the total buffer
time increasing, but the time delayed will remain constant.
4. To return to live listening simply press and hold the PausePlus button.
3,4
The radio will revert to the normal station name display.
Once PausePlus has been cancelled, it will not be possible to go back
to a previously stored part of the program.
The radio will no longer be using the SD/SDHC card to buffer the
current program.
PausePlus rewind and fast-forward - DAB and FM
1. Press the Rewind or Fast Forward button to scroll forward to the item
you wish to listen to. The display will show the amount of time you
have scrolled back together with the maximum time you can rewind
back to.
1,2
Ashort press steps through a few seconds, and a long press will wind
back more rapidly through the stored program.
2. To return to live listening press and hold the PausePlus button. (See
paragraph 4 above).
1,2
1,2
3. The rewind capacity is approximately 60 minutes.
Note: You must stop the PausePlus feature before you can access other
functions by pressing and holding the PausePlus button. If you attempt
to use other functions on your radio while using the PausePlus feature
a warning message 'Hold REWIND to stop rewinding' will be displayed.
REWIND refers to the PausePlus button on the radio.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
20
020 8758 0338 (Mon-Fri)
Using an SD memory card with your radio
This section describes how to use your radio to access and playback your
audio files via Secure Digital (SD, SDHC) cards. The RecordR can also
record DAB or FM radio stations to SD, SDHC media.
The RecordR has been tested with a wide range of SD/SDHC cards from
512MB to 32GB capacity. Note that cards of less than 512MB capacity
cannot be used. SD/SDHC memory must be formatted to use the FAT 16
or FAT 32 filing system in order to operate in the radio.
1
Please note that there are many different card variants available and it is
not possible to guarantee that all cards will work in the RecordR. In the
event that a particular card is not recognised, please try an alternative
brand or capacity.
Audio formats supported for playback are MP3, WMA, WAV and AAC.
PlaybackdoesnotsupportfilesencodedusingWMAlossless, WMAVoice,
WMA 10 professional, nor files of any format which have DRM protection.
For more details see 'Audio formats' page 44.
The SD card slot is located on the left hand side of the radio.
Cautions:
ToavoidpossibledamagetofilesonyourSDcard,placetheunitinStandby
mode before inserting and removing your SD card.
Inserting and removing SD cards
1. To insert an SD card into your radio push the card label side facing
towards you and gold contacts first into the card slot on the left hand
side of your radio until it clicks.
To remove the card push the card in so that it clicks once more. It will
then be pushed out slightly allowing removal.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Recording to SD/SDHC cards
Your RecordR radio has been designed to allow you to make recordings
to SD/SDHC cards. You may record a current radio programme or you
may use the timed record facility (see page 23).
It is possible to record onto SD/SDHC cards which already contain files
written by the radio or using your computer. The recorded files will be
added to those already present on the card.
3,5
4
Note: You must stop the recording before you can access other functions.
Ifyouattempttouseotherfunctionsonyourradiowhilerecordingawarning
message 'Hold RECORD to stop recording' will be displayed.
Recording a radio program
Long recordings are split into files of just over 30 minutes duration to
help protect recordings against power failure or accidental card removal.
Recordings may also be split to accommodate DAB configuration
changes made by the broadcaster.
1. Select the desired source for recording (DAB or FM radio). Set the
volume to the required listening level (the volume of the recording will
not be affected by this).
2. Insert the card on to which the recording is to be made (card label side
facing towards you and gold contacts first, see proceeding page).
Recording files are named using the radio station name or frequency and
the date and time at which the recording began. If the recording is split,
then the subsequent parts of the recording are given a sequence number
to allow the radio to play them as a set, as shown:
3. Press and hold the Record button. The display will show the record
symbol . Recording will then start with the recording source shown
on the display. Record duration may be up to 23 hours and 59 minutes.
Recording will stop if the SD/SDHC card becomes full.
BBC R4,21-09-2011,12-15.mp2
BBC R4,21-09-2011,12-15_01.mp2
BBC R4,21-09-2011,12-15_02.mp2
BBC R4,21-09-2011,12-15_03.mp2
4. While a recording is in progress the Play / Pause button may be used
to temporarily suspend recording. Asecond press of the Play / Pause
button will resume recording.
5. In order to stop the recording press and hold the Record button once
more. Recording will stop and a file will have been written to the SD
card. The recording will be stored and the display will show 'Saved'.
Recordings may be played in the radio in SD card mode, or using media
player programs on a computer (e.g. Windows Media Player).
If you need any further advice, please call our Technical Helpline on :-
020 8758 0338 (Mon-Fri)
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Making a recording cont.
Note: The SD card should only be removed when recording is stopped.
Removing the SD card while recording is in progress may corrupt data
on the card leading to the loss of files previously written.
Files that have been written to the SD/SDHC card are held in folders.
Recordings are held in sub-folders according to the source used for the
recording.'LAST'(Lastrecordingmade), 'DABRec'(DABrecordings),FM
Rec' (FM recordings) and 'REWIND' (used for files recorded to memory
using the PausePlus feature).
The illustration shows the folders as they may appear on a PC running
Windows.
Timed recording
Timed record is available on DAB and FM to SD/SDHC cards and is
provided for personal use only. When making recordings take care to
observe all legal requirements and ensure that the copyright of third
parties is not infringed.
Your radio has four record timers. Each timer can be set to different days
and times. Recording timers may be set when the radio is in use or when
it is in standby. Timers cannot be used when running on batteries as the
clock is set from the DAB broadcast and does not run in battery mode.
Recording duration may be up to 23 hours and 59 minutes.
1. Insert an SD/SDHC card with sufficient capacity for the required
recording. DAB recordings require approximately 64 megabytes per
hour at a DAB data rate of 128 kilobits per second.
FM recordings require approximately 128 megabytes per hour.
Note: If you do not insert an SD card your recording will not take place
and a warning 'No SD Card' will be shown on the display.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Timed recordings cont.
2. Press and hold the Info button.
3. Press the Tuning Up or Down buttons until 'Recorder Set' appears
on the display. Press and release the Select button to enter the timer
record setup.
2
4. 'REC 1' flashes on the display.
5. Press the Tuning Up or Down buttons to select the desired record
timer 1, 2, 3 or 4.
3-7
3-7
6. Press and release the Select button to enter the setting for the chosen
timer. You will need to select the record source. Press the Tuning Up
or Down buttons to select DAB, FM or OFF. If OFF is selected any
current setting for that record timer will be cancelled.
3-8
7. Press and release the Select button. The first preset station in
the list will appear on the display. Press the Tuning Up or Down
buttons to select the desired preset 1-5.
Note:Youcanonlysetuparecordtimerifapresethasbeenpreviously
stored when in DAB and FM modes. Please see 'Presetting stations'
page 18.
8. Press and release the Select button, the timer day option will flash
on the display.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
24
020 8758 0338 (Mon-Fri)
9. Press the Tuning Up or Down buttons to choose the desired timer
day option:
Daily
- will record everyday
Date
- will record on a set date
Weekdays
Weekends
Weekly
Once
- will record only on weekdays
- will record only on weekends
- will record on a set day of the week
- will record at one time only
9-14
9-14
If setting the record timer to the date option, continue with step 10
below. If setting the record timer to Weekly skip to step 14. Otherwise
skip to step 15 on the next page.
10-14
10. Press and release the Select button. The year will flash on the display.
11. Press the Tuning Up or Down buttons to choose the year. Press and
releasetheSelectbuttontoentertheyearsetting.Themonthwillflash
on the display.
12. Press the Tuning Up or Down buttons to choose the month. Press
and release the Select button to enter the month setting. The day will
flash on the display.
13. Press the Tuning Up or Down buttons to choose the day. Skip to step
15 on the next page.
14. Press and release the Select button. The day of the week will flash
on the display. Press the Tuning Up or Down buttons to choose the
day.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
15. Press and release the Select button. The record start hour will flash
on the display. To set the hour, press the Tuning Up or Down buttons.
Press and hold the Tuning Up or Down buttons to advance the time
quickly.
15-20
16. Press and release the Select button. The minute digits will flash on the
display. To set the minutes, press the Tuning Up or Down buttons.
17. Press and release the Select button. The record end hour will flash on
the display. To set the hour, press the Tuning Up or Down buttons.
15-19
15-19
18. Press and release the Select button. The minute digits will flash on the
display. To set the minutes, press the Tuning Up or Down buttons.
19. Press and release the Select button to confirm your record timer
settings. The display will show 'Exit with saving'.
20. Press and release the Select button to save your settings.
Note: Once the timed record function has been set the timer record icon
will appear in the display when the unit is in standby. If the SD card is
absent or write-protected then the radio will display instead of
.
If your radio is in the standby mode it will switch on at the selected record
time and the radio will tune to the station specified for the timed recording.
If your radio is already playing it will tune to the station specified for the
timed recording.
The record icon
will appear on the display while the radio is recording.
The radio will go to Standby after the recording is completed.
If the SD card is absent, the radio will still switch on and play the specified
radio station for the duration required.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
26
020 8758 0338 (Mon-Fri)
View record timers
1. Press and hold the Info button.
2. Press the Tuning Up or Down buttons until 'Recorder Set' shows on
the display. Press and release the Select button to enter the timed
record setup.
1
3. Press the Tuning Up or Down buttons to view timer 1, 2, 3 or 4.
4. Press and release the Select button to cycle through each of the
2,4
settings for the chosen timer.
2,3
2,3
You may use theTuning Up and Down buttons to modify any particular
setting if desired, using the Select button to enter the modification.
Disabling record timers
1. To disable a record timer enter the timed record setup (see page
24, step 2 to 4) and press the Tuning Up or Down buttons until the
desired record timer is highlighted on the display. Press and release
the Select button.
1,2
1,2
2. Press the Tuning Up or Down buttons until 'OFF' is shown on the
display. Press and release the Select button. The chosen timer will
now be disabled.
1,2
Cancelling a recording
1. To cancel a timed recording whilst recording is in progress press and
hold the Record button. The recording will be stored and 'Saved' will
show on the display.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Playing files - SD
1. Press the On / Off button to switch on your radio.
2. To select the SD mode press and release the Band button until the
SD mode is shown on the display. Your radio will start playing from
the SD card. It may take several seconds to read the data on the SD/
SDHC card.
2
3
4
3. To pause playing, press the Play / Pause button. To resume playing,
press the Play / Pause button again.
4. To Stop play, press the Stop button. The total number of files and
folders on the media and the stop symbol will be displayed.
If you put the unit into standby mode without pressing the Stop button,
then the next time the unit is switched on it will resume playback from the
beginning of the previously played track.
Ifadifferentcardisinserted,theradiowillplaybackfilesinthefollowingorder.
- LAST folder *
- DAB Rec folder *
- FM Rec folder *
- User added folders in numeric-alpha order
*
Thesefoldersarecreatedbytheradioifithasmadeanyrecordings
to the card.
Display modes - SD
1. Your radio has a range of display options when in SD mode. Press
and release the Info button to cycle through the various options.
1
MP3, WMA, AAC - title, album, artist, genre, folder, audio type, bit rate
DAB/FMfiles-filename,scrollingtext,foldername,audiotypeandbitrate.
Note: The information displayed will vary according to the file type.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
28
020 8758 0338 (Mon-Fri)
File navigation
1. WhiletheSDcardisplaying, presseitherthe Fast-forwardorRewind
buttons to change to the desired file. The file number will be updated
in the display. If there is more than one folder, when all files in the
current folder have been played the next folder will be played.
1
1
1
1
Search function
1. While the SD card is playing, press and hold the Fast-forward or
Rewind buttons. Release the button when the desired part of the
current file is reached.
Folder navigation
You may choose to organise your music files using folders for artist and
album selection. See page 44 for folder and file name information.
1. Press and hold the Play / Mode button to access the folders on your
SD/SDHC card. The top line shows the current folder and the lower
line shows the folders/or files contained within this folder. Your folders/
or files will be in numeric-alpha order.
1
Pressing the Play / Mode button if you are in a sub folder will take
you to the folder at a higher level.
2. Press the Tuning Up or Down buttons to navigate through the folder/
or file list.
2
2
3. To enter a lower level folder press the Select button.
When the file you want to play is displayed, press the Select button
to play your chosen file.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Repeat a single file
1. While the SD file is playing, press the Play / Mode button until the
repeat single file symbol
appears in the display. The current file
will be repeated.
1-5
Repeat Folder
2. While the SD file is playing, press the Play / Mode button until the
repeat folder symbol appears in the display. All of the files in the
folder will be played repeatedly.
Repeat all files
3. While the SD file is playing, press the Play / Mode button until the
repeat all files symbol
appears in the display. All of the files on
the SD card will be played repeatedly.
Shuffle tracks
4. While the SD file is playing, press the Play / Mode button until the
shuffle symbol
appears in the display. The files will be shuffled.
Play file introduction
5. While the SD card is playing, press the Play / Mode button until
the file introduction symbol
appears in the display. The first 10
seconds of each file will be played. When the desired file is reached,
press the Play / Mode button to revert to normal play mode.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
30
020 8758 0338 (Mon-Fri)
SD memory card information - DAB or FM
InDABorFMmodeyoucandisplaythecapacityavailableonanSD/SDHC
card. This is useful if you wish to use the card for recordings.
1. Ensure you have the SD/SDHC card inserted into the radio and that
your radio is switched on.
2
2. Press and hold the Info button.
3. Press the Tuning Up or Down buttons until 'SD Information' appears
3,5
3,5
on the display.
4. Press and release the Select button to view the SD card information.
4
5. Press the Tuning Up or Down buttons to view the total space on the
SD card or to view the free space remaining.
SD memory card information - SD
In SD mode you can display the number of files and folders that are
present on an SD card.
1. Ensure your radio is SD mode.
2. Follow steps 2-4 above to view SD memory card information.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Setting alarm times
Your radio has four alarms which can be set to wake you to DAB, FM radio,
SD card or beep type alarm. Each alarm can be set to sound once, daily,
on a specific date, weekdays, weekends or weekly. The alarms may be set
while the unit is in Standby mode or while playing. Alarms cannot be used
when running on batteries as the clock is reset from the DAB broadcast
and does not run in battery mode.
1
Note: If no buttons are pressed for several seconds, your radio will exit
the alarm setup.
1. Press and hold the Info button. Press the Tuning Up or Down buttons
1-7
1-7
until 'Alarm Set' shows on the display.
2. Press and release the Select button to enter the alarm setup. Alarm
1' flashes on the display.
2,6
3. Press the Tuning Up or Down buttons to select the desired alarm
timer 1, 2, 3 or 4.
4. Press and release the Select button. The alarm status will flash on
the display.
5. Press the Tuning Up or Down buttons to select On or Off. If 'Off' is
selected any current setting for that alarm will be cancelled.
6. Press and release the Select button. The alarm hour will flash on the
display.
7. Press the Tuning Up or Down buttons to set the alarm hour. Press
and hold the Tuning Up or Down buttons to advance the time quickly.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
32
020 8758 0338 (Mon-Fri)
8. Press and release the Select button. The minute digits will flash on
the display.
9. Press the Tuning Up or Down buttons to set the alarm minute.
8-15
10. Press and release the Select button. The alarm day option will show
on the display.
11. Press the Tuning Up or Down buttons to select the required day
option.
9-14
9-14
Daily
- will sound everyday
Date
- will sound on a set date
Weekdays
Weekends
Weekly
Once
- will sound only on weekdays
- will sound only on weekends
- will sound on a set day of the week
- will sound at one time only
•
•
If setting the alarm to the date option, continue with step 12 below.
If setting the alarm to Weekly skip to step 17 otherwise skip to step
18 overleaf.
12. Press and release the Select button. The year will flash on the display.
13. Press the Tuning Up or Down buttons to choose the year. Press and
release the Select button to enter the year setting. The alarm month
will flash on the display.
14. Press the Tuning Up or Down buttons to choose the month.
15. Press and release the Select button to enter the month setting. The
alarm day will flash on the display.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
16. Press the Tuning Up or Down buttons to choose the alarm day. Skip
to step 18 below.
17. Press and release the Select button. The day of the week will flash
on the display. Press the Tuning Up or Down buttons to choose the
desired day of the week.
16-19
16-19
18. Press and release the Select button. The alarm source option will
show on the display.
17-20
19. Repeatedly press the Tuning Up or Down buttons to choose the
desired alarm source (DAB, FM, SD or Buzzer).
If setting the alarm to the radio option, the radio alarm may be set to
any of the stations which have been stored as presets.
Press the Tuning Up or Down buttons to choose from preset 1-5 on
the display.
Note: That you can only set the alarm to use a preset which has
already been stored. Please see 'Presetting stations' page 18.
20. Press and release the Select button to confirm your alarm settings.
The display will show 'Exit with saving'. Press and release the Select
button to save your settings.
Active alarms are indicated in the display by the alarm symbol.
When the alarm activates it will start softly and gradually increase in level.
The final volume is set by the volume control.
Note: It is not possible to lower the volume of your radio fully while playing
analarm.Thisisbecauseyourradiomodifiesthevolumecontrolbehaviour
during an alarm so that an alarm can still be heard even if the control was
accidentally set to minimum.
Important: If using the SD card for the source for the alarm, then be sure
to have inserted an SD card see page 21.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
34
020 8758 0338 (Mon-Fri)
To view the alarm settings
1. Press and hold the Info button.
2. Press the Tuning Up or Down buttons until 'Alarm Set' shows on the
display. Press and release the Select button to enter the alarm setup.
1
3. Press the Tuning Up or Down buttons to view alarms 1, 2, 3 or 4.
4. Press and release the Select button to cycle through each of the
settings for the chosen alarm.
2,3
2,3
You may use theTuning Up and Down buttons to modify any particular
setting if desired, using the Select button to enter the modification.
2,4
Cancelling alarms
1. While an alarm is sounding it can be cancelled by pressing the On / Off
1
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Snooze function
1. When the radio, SD or buzzer alarm sounds, pressing any button
(except the On /Off button) will silence the alarm for 5 minutes.
The Snooze symbol
and the alarm symbol will flash on the display.
This sequence can be repeated during the 60 minute alarm period.
2
2. To cancel the Snooze function, press the On / Off button.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
36
020 8758 0338 (Mon-Fri)
Sleep function
Your radio can be set to turn off after a preset time has elapsed. The sleep
settingcanbeadjustedbetween5and120minutesin5minuteincrements.
Ensure your radio is switched On.
1
1. When using your radio, press and hold the Info button.
2. Press the Tuning Up or Down buttons until 'Sleep Set' shows on the
display.
3. Press and release the Select button to enter sleep menu.
2,4
2,4
4. Press the Tuning Up or Down buttons to select desired sleep time.
The sleep setting will increase in 5 minute increments from 5 minutes
up to 120 minutes. A further press will cause the sleep timer to be set
to OFF which will cancel the sleep function.
3,5
5. Press and release the Select button. The display will exit the sleep
options. The sleep symbol will show on the display.
6. Your radio will switch off after the preset sleep time has elapsed.
7. To cancel the sleep timer and switch off your radio before the chosen
sleep time has elapsed, press the On / Off button.
7
To cancel the sleep timer without switching off your radio, choose the
'OFF' setting in step 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Nap timer
The Nap timer facility allows you to set the radio to wake you after a
pre-determined interval (up to 2 hours) without needing to set the alarms.
You may set the nap timer while the unit is in standby or while playing.
The nap timer cannot be used when running on batteries.
1
1. Press and hold the Info button.
2. Press the Tuning Up or Down buttons until 'Nap Set' shows on the
display.
2,4
2,4
3. Press and release the Select button to enter setup menu.
4. Press the Tuning Up or Down buttons to select desired nap time.
The nap setting will increase in 5 minute increments from 5 minutes
up to 120 minutes. A further press will cause the nap timer to be set
to OFF which will cancel the nap function.
3,5
5. Press and release the Select button. The display will exit the nap
options. The nap symbol will show on the display when the unit is
in Standby.
7
6. When the selected nap timer has elapsed, the radio buzzer will sound.
7. To cancel the buzzer when it sounds press the On / Off button.
To cancel the nap timer without switching off your radio, choose the
'OFF' setting in step 4.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
38
020 8758 0338 (Mon-Fri)
Contrast / viewing angle control
The contrast of the display can be adjusted while the unit is playing. The
adjustmentalsochangestheanglefromwhichthedisplaycanbestbeseen.
1. Ensure your radio is switched on.
2
2. Press and hold the Info button.
3. Press the Tuning Up or Down buttons until 'Contrast' appears on the
display.
3,5
3,5
4. Press and release the Select button.
5. Press the Tuning Up or Down buttons to adjust the contrast. The
contrast level indication on the screen will change at the same time.
4,6
6. Press and release the Select button to confirm the setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Display backlight dimmer
The brightness of the display can be adjusted when the radio is in use and
when it is in standby. If you use the unit in a bedroom, you may prefer a
lowerbrightnesslevelthanthestandardsetting.Therearethreebrightness
levels and an almost off 'night time' setting.
1,2
1. When the radio is in standby press and release the Info button to
adjust the brightness level.
2. To adjust the display brightness when the radio is in use, press and
hold the Info button.
3,4
3,4
3. Press the Tuning Up or Down buttons until 'Backlight' appears on
the display. Press and release the Select button.
3,5
4. Press theTuningUpbuttontoincreasethebrightnessandtheTuning
Down button to the decrease brightness.
5. Press and release the Select button to confirm the setting.
Note:Whenusingtheradiopoweredbythebatteries, thedisplaybacklight
willbeswitchedonforapproximately10secondswhenanybuttonispressed.
Clock display
1. Whenyourradioisinstandbymodethetimeanddatewillbedisplayed.
The time is always shown using a 24 hour clock format.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
40
020 8758 0338 (Mon-Fri)
System reset
If your radio fails to operate correctly, or some digits on the display are
missing or incomplete carry out the following procedure.
1. Ensure your radio is switched on. Press and hold the Info button.
1
2. Press and release the Tuning Up or Down buttons until 'Factory
Reset' appears on the display. Press and release the Select button.
3. Press and release the Tuning Up or Down buttons until 'Yes' appears
on the display. If you do not wish to carry out a system reset, highlight
'No' and then press the Select button. The display will revert to the
previous display.
2,3
2,3
4. With 'Yes' displayed, press and release the Select button. A full reset
will be performed. The station list and presets will be erased. Timers
and alarms will be cancelled and sleep and nap timer settings will be
set to their default values. The display will show 'Welcome ROBERTS'
and after a few seconds a station scan search will be performed
automatically. The display will show progress of the station search.
The number on the right of the display is the number of stations that
have been found.
2,4
In case of malfunction due to electrostatic discharge, reset the product as
above to resume normal operation.
It may be necessary in some cases to disconnect the mains power and
remove batteries, then reconnect power after 10 seconds.
If a problem persists our technical staff would be pleased to offer any
assistance on operating the radio. Our technical helpline number is
020 8758 0338.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Headphone socket
A 3.5mm stereo Headphone Socket located on the left hand side of your
radio is provided for use with either headphones or an earpiece. Inserting
a plug automatically mutes the internal loudspeaker.
Please be aware that the sensitivity of headphones can vary widely. We
therefore recommend setting the volume to a low level before connecting
headphones to the radio.
IMPORTANT:Excessivesoundpressurefromearphonesandheadphones
can cause hearing loss.
Auxiliary Input (Line in) socket
A3.5mm stereo Auxiliary Input socket is provided on the left hand side of
your radio to permit an audio signal to be fed into the unit from an external
audio device such as iPod, MP3 or CD player.
1. Connect a stereo or mono audio source (for example, iPod, MP3 or
CD player) to the Auxiliary Input socket (marked "Aux In").
2. Press and release the Band button until 'AUX' is selected on the
display. Auxiliary In mode is only available when a plug is inserted
into the Auxiliary Input socket.
2
3. Adjust the Volume control on your iPod, MP3 or CD player to ensure
an adequate signal and then adjust the volume on the radio for
comfortable listening.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
42
020 8758 0338 (Mon-Fri)
Software version
The software display cannot be altered and is just for your reference.
Ensure your radio is switched on.
1. Press and hold the Info button.
1
2. Press the Tuning Up or Down buttons until 'SW Version' appears on
the display.
3. Press and release the Select button to view the software information.
2
2
4. After several seconds your radio will exit the menu.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Audio formats
Bit-Rates
The following table summarises the maximum supported bit-rates for the various audio formats that are playable on your radio. Higher rates may be
playable in some cases but performance of the product may be affected.
Codec
AAC (LC)
MP3
Maximum supported rate
320 kbits/sec
320 kbits/sec
WAV (1)
WMA (2)
1536 Mbits/sec
320 kbits/sec
All codecs support 2-channel (stereo) coded files only.
All codecs support sample rates up to 48 kbits/sec (includes 32 and 44.1 kbits/sec).
SD/SDHC playback supports MP3 and WMA formats only.
Files which have Digital Rights Management (DRM) protection applied will not be playable on your radio.
(1) The maximum supported bit-rate is for 48 kHz sampling, 2 channels and 16-bits per sample.
There are many variants of WAV format. 16 bit PCM stereo is supported. Most other variants are not supported.
(2) WMA Lossless, WMA Voice, WMA 10 Professional, and files which have DRM protection are not supported.
SD/SDHC card information
Listed here are guidelines for SD/SDHC cards to be used in your radio.
1. Card capacity must be between 512MB and 32GB.
2. Card must be FAT16 or FAT32 formatted.
3. We recommend less than 500 files or folders are placed in the root folder.
4. We recommend less than 10,000 files are placed on a card.
5. We recommend that folders are nested less than 10 levels deep.
6. We recommend that file and folder names are less than 128 characters long.
7. Actual limits (points 3, 4, 5, 6) are higher and are set by the card format.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
44
020 8758 0338 (Mon-Fri)
Cautions
Do not allow this radio to be exposed to water, steam or sand. Do not
leave your radio where excessive heat could cause damage such as in
a parked car where the heat from the sun can build up even though the
outside temperature may not seem too high. It is recommended that the
DAB band be used wherever possible as better results in terms of quality
and freedom from interference will usually be obtained than on the the
FM band.
•
•
Your radio should not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on the radio.
It is recommended to operate the product such that there is a minimum
distance (10cm recommended) to adjacent objects in order to ensure
good ventilation.
•
The ventilation of the product should not be restricted by covering it or
its ventilation openings with items such as newspapers, tablecloths,
curtains etc.
•
The name plate is located on the rear of the unit.
•
•
No naked flame sources such as lighted candles should be placed on
the product.
It is recommended to avoid using or storing the product at extremes
of temperature.Avoid leaving the unit in cars, on window sills, in direct
sunlight etc.
Specifications
Circuit Features
Power Requirements
Loudspeaker
Output Power
75mm
Mains
AC 100
240V 50/60Hz (Adaptor)
0.8 Watts
Batteries
4 x LR20 (D size)
Headphone socket
3.5mm dia
3.5mm dia
Battery Life
Auxiliary Input socket
Up to 120 hours of listening for 4 hours a day at normal volume using
alkalinecellsaccordingtotheoperatingmode.Longerplaybacktime
may be achieved when using SD playback orAuxiliary input modes.
Aerial System
FM
DAB
Telescopic aerial
Telescopic aerial
Frequency Coverage
FM
87.5-108MHz
DAB
174.928 - 239.200MHz
The Company reserves the right to amend the specification without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Guarantee
This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty workmanship or component
breakdown, subject to the procedure stated below. Should any component or part fail during this guarantee period it will be repaired or replaced free
of charge.
The guarantee does not cover:
1. Damage resulting from incorrect use.
2. Consequential damage.
3. Receivers with removed or defaced serial numbers.
N.B. Damaged or broken telescopic aerials will not be replaced under guarantee.
Procedure:
Any claim under this guarantee should be made through the dealer from whom the instrument was purchased. It is likely that your Roberts' dealer
will be able to attend to any defect quickly and efficiently but should it be necessary the dealer will return the instrument to the Company’s service
department for attention. In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact
Roberts Radio Technical Services at the address shown overleaf.
These statements do not affect the statutory rights of a consumer.
If you need any further advice, please call our Technical Helpline on :-
Download from Www.Somanuals.com. All Manuals Search And Download.
46
020 8758 0338 (Mon-Fri)
ROBERTS RADIO TECHNICAL SERVICES
97-99 Worton Road
Isleworth
Middlesex
TW7 6EG
Technical Helpline :- 020 8758 0338 (Mon-Fri during office hours)
Issue 1
© 2011 Roberts Radio Limited
Download from Www.Somanuals.com. All Manuals Search And Download.
|