Rimage Pet Fence RAS10 User Guide

Rimage AutoPrinter™  
User Guide  
This manual provides the information needed to operate the AutoPrinter and identify the parts.  
To setup and install your AutoPrinter, refer to the Setup and Installation Guide included with your  
product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Corporate Headquarters:  
Rimage Corporation reserves the right to make  
improvements to the equipment and software  
described in this document at any time without any  
prior notice. Rimage Corporation reserves the right to  
revise this publication and to make changes from  
time to time in the content hereof without obligation of  
Rimage Corporation to notify any person or  
Rimage Corporation  
7725 Washington Avenue South  
Minneapolis, MN 55439  
USA  
800 553 8312 (toll free US)  
Service: +1 952 946 0004  
(International)  
organization of such revisions or changes.  
This document may contain links to web sites that  
were current at the time of publication, but may have  
moved or become inactive since. This document may  
contain links to sites on the Internet that are owned  
and operated by third parties. Rimage Corporation is  
not responsible for the content of any such third-party  
site.  
Fax: +1 952 944 6956  
European Headquarters:  
Rimage Europe GmbH  
Hans-Böckler-Straße 7  
63128 Dietzenbach, Germany  
Tel: +49-(0) 6074-8521-0  
Fax: +49-(0) 6074-8521-21  
©2006, Rimage Corporation  
CD and DVD Recording Software  
Disclaimer  
Rimage™ is a trademark of the Rimage Corporation.  
AutoPrinter™ is a trademark of the Rimage  
Corporation. Dell® is registered trademark of Dell  
This Product, Software, or Documentation may be  
designed to assist you in reproducing material in  
which you own the copyright or have obtained  
permission to copy from the copyright owner.  
Unless you own the copyright or have permission  
to copy from the copyright owner, you may be  
violating copyright law and be subject to payment  
of damages and other remedies. If you are  
uncertain about your rights, you should contact  
your legal advisor. If you are neither in possession  
of the copyright nor have authorization from the  
owner of the copyright, unauthorized copying of  
CDs violates national and international legislation  
and can result in severe penalties.  
Computer Corporation. FireWire® is a registered  
trademark of Apple Computer, Inc.  
All other trademarks and registered trademarks are  
the property of their respective owners.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Support information  
US, Asia/Pacific, Mexico/Latin America  
Europe  
Rimage Corporation  
7725 Washington Avenue South  
Minneapolis, MN 55439  
USA  
Rimage Europe GmbH  
Hans-Böckler-Straße 7  
63128 Dietzenbach, Germany  
Tel: +49-(0) 6074-8521-0  
Attn: Rimage Services  
FAX: +49-(0) 6074-8521-21  
Service:  
North America: 800-553-8312  
Asia/Pacific, Mexico/ Latin America: 952-946-0004  
Select the appropriate Support link to  
learn more. If you cannot find a solution  
on our website, email Rimage Services,  
Europe at [email protected].  
FAX: 952-946-6956  
When you contact Rimage Services, please provide:  
Unit serial number and software version.  
Functional and technical description of the problem.  
Exact error message received.  
Learn more online  
At www.rimage.com/support.html, you can experience Rimage’s world-class Support and  
Services.  
1. Select your product family.  
2. Select your product.  
3. Learn more on your  
product page.  
From your product page you can access:  
Information about the latest software and firmware updates  
Product specifications  
Troubleshooting tips and FAQs  
The latest documents  
Printing tips  
Current firmware and driver downloads  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Contents  
110656_H  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rimage AutoPrinter™ User Guide  
.
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Introduction  
This manual provides the information needed to operate the AutoPrinter and identify the parts. To  
setup and install your AutoPrinter, refer to the Setup and Installation Guide included with your  
product.  
Note: The term AutoPrinter applies to both the AutoEverest and the AutoPrism. AutoEverest  
and AutoPrism will be used only to refer to either AutoPrinter specifically.  
AutoEverest  
AutoPrism  
Operating system requirements  
AutoEverest  
Windows-based PC  
The AutoEverest will run only on Windows 2000 Professional with SP4, Windows XP Professional  
with SP1 or SP2, and Windows Server 2003.  
Macintosh  
The AutoEverest will run only on Macintosh OS X v10.3/10.4.  
AutoPrism  
The AutoPrism will run only on Windows 2000 Professional with SP4, Windows XP Professional  
with SP1 or SP2, and Windows Server 2003.  
Media requirements  
Refer to your Everest Printer User Guide or PrismPlus! Printer User Guide for the correct media  
requirements.  
Ribbon requirements  
Refer to your Everest Printer User Guide or PrismPlus! Printer User Guide for the correct printer  
ribbons.  
Label design requirements  
Refer to your Everest Printer User Guide or PrismPlus! Printer User Guide for label design  
requirements.  
110656_H  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Rimage AutoPrinter  
Identify the parts of the AutoPrinter  
Front view  
Lift Arm  
Lift Arm  
Prism  
Printer  
Everest  
Printer  
Control  
Panel  
Control  
Panel  
Operator  
Panel  
Operator  
Panel  
Carousel  
Carousel  
AutoEverest  
AutoPrism  
2
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Identify the parts of the AutoPrinter  
Operator panel  
The operator panel has four indicator lights and an operator button.  
Operator button  
Each time you press the operator button, the carousel rotates to the next bin.  
Operator panel  
The indicator lights on the operator panel provide the following operational information:  
Name  
Functionality  
Carousel  
Present  
The carousel present indicator light illuminates when the  
carousel is absent.  
Active  
Power  
The active indicator light illuminates when the computer is  
communicating with the AutoPrinter.  
The power indicator light illuminates when the AutoPrinter is  
powered on.  
Fault  
The fault indicator light, located on the operator button,  
illuminates if an error is detected.  
110656_H  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rimage AutoPrinter  
Rear view  
Printer Control Cable  
Everest Printer  
USB  
Cable  
Printer Control Cable  
USB  
Cable  
Prism  
Printer  
Prism Power  
Switch  
Serial Cable*  
Power  
Switch  
Power  
Switch  
AutoEverest  
AutoPrism  
*Serial cable is used only for updating the firmware. Do not connect a serial cable during normal  
operation.  
4
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operate the AutoPrinter  
Operate the AutoPrinter  
Installing the carousel  
- Important: To prevent errors, the carousel should be installed before operating the software  
or powering on the AutoPrinter.  
1. Slide the carousel into the unit so that  
the shaft slides in the slot opening of  
the bearing guide.  
Top Support Bearing  
Bearing Guide  
2. Lower the carousel with the top  
support bearing dropping in to the  
bearing guide.  
Shaft  
3. If necessary, rotate the carousel to seat  
the carousel securely.  
Powering on and off  
Before you begin:  
The carousel must be installed before you power on the system. For more information about  
installing the carousel, refer to Installing the carousel on page 5.  
Note: The Prism printer power switch must be in the ‘on’ position. The Everest printer does  
not have a power switch. The Everest printer is powered on when the AutoPrinter is powered  
on.  
The Everest printer takes 1 to 2 minutes to complete the initialization.  
1. To power on the AutoPrinter, press the power  
switch on the rear of the AutoPrinter.  
Power Switch  
2. To power off the AutoPrinter, press the power  
switch.  
110656_H  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Rimage AutoPrinter  
Loading and unloading discs  
You can load up to 100 discs per carousel bin. You may load discs in the bins before installing  
the carousel.  
When the carousel is installed in the AutoPrinter, discs can be installed one bin at a time by  
following the procedure below.  
Load the discs  
1. Press the operator button to rotate the carousel and place a bin in position to load blank  
discs.  
2. Remove any completed discs from the carousel bins.  
3. Place blank discs in bins 1–3 of the carousel. The AutoPrinter will pick discs from the next  
bin once the first bin is empty. Bin 4 is only used for outputting completed discs.  
- Important! Place the discs into the bins with the recording side facing down.  
#Tip: Hold the discs by the outer edge so you do not put fingerprints on either the top or  
the bottom surface of the discs. Fingerprints on the top of the disc can affect printing  
quality. Rimage recommends wearing lint free gloves.  
4. Repeat steps 1–2 until the required bins are filled.  
Unload the discs  
1. Press the operator button to rotate the carousel and place a bin in position to unload discs.  
2. Remove the discs from the desired bin.  
Reset the AutoPrinter to pick discs from bin 1  
After the AutoPrinter starts picking discs from bin 2 or 3, it continues picking discs from that bin  
until the AutoPrinter is powered off, or the AutoPrinter is reset.  
1. To reset the AutoPrinter to start picking discs from bin 1, lift the carousel up and down so the  
carousel present indicator light turns on and off.  
2. Add discs to bin 1. The next print job will start picking from bin 1.  
Setting printing preferences  
Printing preferences allows you to set and run your AutoPrinter to produce the best possible label  
on your discs. Refer to your Everest Printer User Guide or PrismPlus Printer User Guide for  
specific printing preferences instructions.  
6
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Maintain the AutoPrinter  
Maintain the AutoPrinter  
Installing ribbons  
Before installing ribbons in the printer, stop any operations.  
To change ribbons in a Prism printer, refer to the PrismPlus Printer User Guide.  
To change ribbons in an Everest II printer, refer to the Everest II Printer User Guide.  
Cleaning method and schedule  
Task  
Frequency  
Cleaning the AutoPrinter  
Once a week. Remove dust from the AutoPrinter and  
surrounding work area.  
Aligning the printer  
Upon installation and again if the discs are not picked  
correctly from the printer tray. Refer to the procedures below  
for more information.  
Aligning the printer  
Everest printer  
To align your Everest printer, use the following instructions.  
#Required tools:  
T25 Torx screwdriver  
5/32” Allen wrench  
1. Power on the AutoPrinter.  
2. Wait for the unit to complete initialization. When initialization is complete, the active indicator  
light on the Everest printer illuminates.  
Note: The Everest printer takes 1 to 2 minutes to complete the initialization.  
Lift  
Arm  
3. Prepare the unit for alignment.  
a. Manually slide the lift arm to the top of  
the AutoPrinter.  
b. To place a disc in the gripper, press  
the disc up into the gripper while  
pressing the disc release button.  
c. Release the disc release button. The  
gripper holds the disc.  
d. Press the printer button to open the  
printer tray.  
Disc Release Button  
Gripper  
110656_H  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Rimage AutoPrinter  
4. Align the printer.  
a. Slowly slide the lift arm down  
until the disc just touches the  
print pad.  
Lift  
Arm  
Printer  
Button  
b. If the disc is not centered  
on the print pad, align the  
printer side to side.  
Side to Side  
Alignment  
Print  
Pad  
Holding Pins  
Front to Back  
Alignment Screw  
i. Using the T25 Torx screwdriver,  
loosen the two side to side  
alignment screws.  
ii. Slide the printer, not the printer  
tray, until the side edges of the  
disc and printer pad are aligned.  
iii. Tighten the two side to side  
alignment screws.  
#Tip: Tighten each screw in  
Side to Side  
Alignment Screws  
increments to prevent shifting.  
c. Using either a T25 Torx driver or a  
5/32” Allen wrench, turn the front to  
back alignment screw until there is  
a 1/16” (1.5mm) gap between the  
front edge of the disc and the raised  
edge of the disc retainer.  
Gap  
Disc  
Retainer  
5. When the printer is aligned, slide the lift arm to the top of the unit.  
6. Press the printer button to close the printer tray.  
7. Press the disc release button to release the disc from the gripper.  
#Tip: Place your hand under the disc to catch it.  
8
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintain the AutoPrinter  
Prism printer  
To align your Prism printer, use the following instructions.  
#Required tools:  
T25 Torx screwdriver  
5/32” Allen wrench  
1. Power on the AutoPrinter.  
Note: If the Prism power switch is in the on position, power on both the printer and the  
AutoPrinter by pressing the AutoPrinter power switch.  
2. Wait for the unit to complete initialization.  
3. Prepare the unit for alignment.  
Lift  
Arm  
a. Manually slide the lift arm to the top of  
the AutoPrinter.  
b. To place a disc in the gripper, push  
the disc up into the gripper while  
pressing the disc release button.  
c. Release the button. The gripper holds  
the disc.  
d. Press the printer button to open the  
printer tray.  
Gripper  
Disc Release Button  
4. Align the printer.  
Printer  
Button  
a. Slowly slide the lift arm  
down until the disc just  
touches the print pad.  
Lift  
Arm  
Side to Side  
Alignment  
Print  
Pad  
Holding Pins  
110656_H  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rimage AutoPrinter  
Side to Side Alignment Screws  
b. If the disc is not centered on the print  
pad, align the printer side to side.  
i. Using the T25 Torx screwdriver,  
loosen the two side to side  
alignment screws.  
ii. Slide the printer, not the printer  
tray, until the side edges of the  
disc and printer pad are aligned.  
iii. Tighten the two side to side  
alignment screws.  
Front to Back  
Alignment Screw  
c. Using either a T25 Torx driver or a  
5/32” Allen wrench, turn the front to  
back alignment screw until the disc  
hangs over the edge of the print pad by  
0.010” – 0.015” (0.25mm – 0.38mm).  
Print Pad  
5. When the printer is aligned, slide the lift arm to the top the unit.  
6. Press the printer button to close the printer tray.  
7. Press the disc release button to release the disc from the gripper.  
#Tip: Place your hand under the disc to catch it.  
10  
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Learn More  
Learn More  
AutoPrinter specifications  
Note: Specifications for the printer are in the printer user guide.  
Standard System  
AutoPrinter autoloader, a Rimage Everest or Prism printer, and  
CD Designer software suite.  
CD Designer or other graphics application  
300 Discs  
Software requirements  
Input bin capacity  
Output capacity  
Physical size  
300 Discs  
Width: 15.063” (38.4 cm)  
Height: 22.375” (56.8 cm)  
Depth: 22.625” (57.5 cm)  
Weight with Everest printer: 97 lb (44.1 kg)  
Weight with Prism printer: 73 lb (33.2 kg)  
Minimum PC  
requirements  
If you do not understand these  
requirements, ask your computer  
technician for help or refer to your  
PC documentation.  
Processor: Pentium II, 450 MHz or higher  
RAM/memory: 256MB  
One USB 1.0 port (used by Everest or Prism printer)  
One parallel port (used by Prism printer)  
Minimum Macintosh  
requirements  
G4  
256 MB  
If you do not understand these  
requirements, ask your computer  
technician for help or refer to your  
computer documentation.  
One USB 1.0 port (Everest printer only)  
Supported Operating  
Systems  
Windows 2000 Professional with SP4, Windows XP Professional  
with SP1 or SP2, and Windows Server 2003  
Macintosh OS X v10.3/10.4 (Everest printer only)  
100 – 240 VAC, 1.5 A, 60/50 Hz  
60°– 80°F (16° – 27°C)  
Power  
Operating Temperature  
Humidity  
40% – 80% non-condensing  
Storage Temperature  
5°– 95°F (-15° – 35°C)  
110656_H  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Rimage AutoPrinter  
Technical support and product updates  
Support for the Rimage AutoPrinter is available through your authorized reseller.  
- Important! Register your Rimage AutoPrinter online or complete and return the registration  
card so that Rimage can notify you of upgrades as they become available.  
Safety information  
This manual and the indications on the product allow for proper and safe operation. The  
indication marks below help protect you and other persons from injury, and the equipment from  
damage.  
nWarning! According to ANSI (American National Standards Institute) standards, a warning is  
used to indicate situations that could result in bodily injury to personnel operating or  
maintaining the equipment.  
p Caution: Indicates that failure to observe this guideline could result in loss or damage to the  
equipment, product, software, or data.  
Safety precautions  
To ensure safety, please read the precautions in the User Guide and familiarize yourself with their  
meaning before using the equipment.  
nWarning: Please observe all warning and caution labels to ensure safety of personnel.  
nWarning: Replace all fuses with the same voltage and current ratings to maintain UL safety  
approvals.  
nWarning: Use the supplied AC power cord, or use a safety agency-approved power cord.  
p Caution: Any equipment that has AC line voltage, or low DC voltages, such as switches,  
power supplies, fuses, fans, non-stepper motors, must be replaced with Rimage–approved  
components to maintain the safety approval issued by UL.  
12  
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Learn More  
Safety testing  
Product name: AutoPrinter  
Model: RAS10  
Notice for USA  
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This product complies with UL 60950 3rd Edition.  
Notice for Canada  
Canadian Department of Communications (DOC) Statement  
This digital apparatus does not exceed the Class B limits for radio noise for digital  
apparatus specified in the Radio Interference Regulations of the Canadian Department of  
Communications.  
C
Product Safety Statement  
This product is in compliance with CSA C22.2 No.60950.  
Notice for Europe  
This product is in conformity with the EMC Directive (89/336/EEC) and the Low-Voltage  
Directive (73/23/EEC) through compliance with the following European standards:  
EN 60950, EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3. The CE mark has been  
affixed in accordance with the CE Marking Directive 93/68/EEC.  
110656_H  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Rimage AutoPrinter  
Rimage AutoPrinter II Limited One Year Warranty  
Rimage warrants, to the original end user only, that all non-consumable parts of the AutoPrinter III will be  
free from defects in material or workmanship for 12 months, according to the following terms:  
Rimage will replace or repair, at Rimage's discretion, any non-consumable parts found defective within  
the Warranty period.  
The 12 month warranty period begins on the date the product ships to you.  
Factory depot repair: Equipment requiring service should be shipped to:  
ƒ
ƒ
ƒ
ƒ
Rimage in Minnesota from a location within the US or Canada with a typical response of 15  
business days from the date of receipt.  
Rimage in Germany from a location in Europe with a typical response of 15 business days from the  
date of receipt.  
Rimage in Japan from a location in Asia / Pacific with a typical response of 15 business days from  
the date of receipt.  
Rimage in Minnesota from a location that is not in the US or Canada with a typical response of 25  
business days from the date of receipt.  
Advanced Exchange replacement or other Maintenance Contracts are available to enhance your  
warranty service.  
Rimage will pay ground service freight charges for components shipped to you.  
The use of non-Rimage certified parts may void this warranty.  
This Warranty does not include the following:  
Work done at the customer's location, or customer's loss of data.  
Shipment costs for equipment or components returned to the Rimage factory.  
Equipment malfunctions as a result of repairs made by persons who are not authorized or certified by  
Rimage.  
Equipment or parts that were tampered with, misused, neglected, or modified in any respect without the  
written consent of Rimage.  
Equipment or parts that have been damaged due to shipping or accidents, or damaged by lightning,  
storms, water, or power surges.  
Printer consumables including ribbons, retransfer ribbons, or print head.  
YOU MAY NOT ASSIGN THIS WARRANTY WITHOUT RIMAGE'S WRITTEN CONSENT. RIMAGE IS THE  
INTENDED BENEFICIARY OF THIS WARRANTY; IF THERE IS ANY INCONSISTENCY BETWEEN THIS  
WARRANTY AND ANY OTHER AGREEMENT INCLUDED WITH OR RELATING TO RIMAGE  
PRODUCTS, THIS WARRANTY SHALL GOVERN. IF ANY TERM OF THIS WARRANTY IS ILLEGAL OR  
UNENFORCEABLE, THE LEGALITY AND ENFORCEABILITY OF THE REMAINING PROVISIONS ARE  
NOT AFFECTED OR IMPAIRED. This Warranty is to be interpreted under the laws of the State of  
Minnesota, without giving effect to conflict of law rules. The provisions of the United Nations Convention on  
Contracts for the International Sale of Goods or the United Nations on the Limitation Period in the  
International Sale of Goods, as amended from time to time, shall not apply.  
Rimage must receive written notice of any claimed defect or failure to perform within five (5) days after such  
failure or defect is first observed. For warranty service, call Rimage US at +952-946-0004,  
Rimage Asia/Pacific at +81-3-5283-8465, or Rimage Europe at +49-0-6074-8521-0.  
THE LIMITED WARRANTY SET FORTH ABOVE IS RIMAGE'S ONLY WARRANTY IN CONNECTION  
WITH THE RIMAGE PRODUCER III FAMILY OF PRODUCTS. ALL OTHER WARRANTIES, WHETHER  
WRITTEN OR ORAL, EXPRESS OR IMPLIED, CONTRACTUAL OR STATUTORY, INCLUDING, BUT NOT  
LIMITED TO ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR  
PURPOSE ARE SPECIFICALLY EXCLUDED AND DISCLAIMED. IN NO EVENT SHALL RIMAGE'S  
LIABILITY UNDER THIS WARRANTY EXCEED THE OBLIGATION TO REPAIR OR REPLACE, AT  
RIMAGE'S DISCRETION, A WARRANTED PRODUCT, AND, WITHOUT LIMITING THE FOREGOING,  
RIMAGE'S LIABILITY UNDER THIS WARRANTY SHALL NOT EXCEED THE COST OF THE COVERED  
PRODUCT.  
14  
110656_H  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Q See Home Security System Q25DVR4ES User Guide
QVS Network Card UR100 User Guide
Reebok Fitness Treadmill RBTL19980 User Guide
Reliable Sewing Machine MSK 755 User Guide
Samsung Air Conditioner AXHM260VE User Guide
Samsung Air Conditioner Model AW089AB User Guide
Samsung Printer STP 103P User Guide
Samsung VCR SV J162P User Guide
Sangean Electronics Portable Radio ATS 606 User Guide
Scientific Atlanta Flat Panel Television Explorer HDTV Setup Wizard User Guide