8900 Series
8900 8920 8905
8955 8925
O w n e r ’ s M a n u a l
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
IMPORTANT SAFETY INSTRUCTIONS
Polarization instructions
2
3
4
5
Thermal fuse protection
Description of the vacuum
Assembly & Operation
Attaching the handle
6
6
Install hose assembly
Release the power cord
On/Off switch
6
6
Handle adjustments
7
Replacing vacuum bag
Replacing secondary filter
Replacing post filter
7
8
8
Replacing headlight bulb
Removing and reinstalling bottom plate
Edge cleaning feature
9
9
9
Automatic self adjusting rug nozzle
Carpet floor selector
9
9
Replacing agitator belt
Unclogging nozzle and hose
Full bag indicator light
ꢀ0
ꢀ2
ꢀ2
Tools
On-board cleaning tools
Suction control dial
Optional cleaning tools
ꢀ3
ꢀ3
ꢀ4
Warranty
ꢀ5
ꢀ7
Owner’s information
Download from Www.Somanuals.com. All Manuals Search And Download.
Polarization instructions
IMPORTANT SAFETY INSTRUCTIONS
Power Cord - 2-Wire Polarized
When using an electrical appliance, basic precautions should always be followed, including
the following:
Household models 8955, 8905, 8900 Only
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
To reduce the risk of electric shock this product is equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician
to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.
The manufacturer cannot accept responsibility for damage
WARNING:
caused when the appliance is not used according to the
instructions, or for uses other than those for which it
was intended.
To reduce the risk of fire, electric shock or injury:
• Do not leave appliance when plugged in.
Unplug from outlet when not in use and
before servicing.
• Do not put any object into openings. Do
not use with any opening blocked; keep
free of dust, lint, hair and anything that
may reduce air flow.
• WARNING: ELECTRIC SHOCK COULD
OCCUR IF USED OUTDOORS OR ON
WET SURFACES.
• Keep hair, loose clothing, fingers and all
parts of body away from openings and
moving parts.
• Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
Grounding Instructions
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches or
hot ashes.
Model 8925 and 8920 Only
• Use only as described in this manual.
Use only manufacturer’s recommended
attachments.
This vacuum cleaner must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock.
This vacuum cleaner is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
• Do not use without vacuum bag and/or
filters in place.
• Do not use with damaged cord or plug. If
appliance is not working as it should, has
been dropped, damaged, left outdoors,
or dropped into water, return it to your
Authorized Retailer for service.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
This vacuum cleaner is for use on a nominal ꢀ20-volt circuit and has a ground plug
(see illustration). Make sure that the vacuum is connected to an outlet having the same
condiagramuration as the plug. No adapter should be used with this vacuum.
• Do not use to pick up flammable or
combustible liquids such as gasoline or
use in areas where they may be present.
• Do not pull or carry by cord, use cord as
a handle, close a door on the cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
WARNING – Improper connection of
• Do not attempt to service the unit while
appliance is plugged in.
Grounded
Outlet
the equipment-grounding conductor
can result in the risk of electric shock.
Check with a qualified electrician or
service person if you are in doubt
as to whether the outlet is properly
grounded. Do not modify the plug
provided with the vacuum – if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use vacuum to pick up water or
any wet materials.
• Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Grounded
Outlet Box
• Use extra care when cleaning on stairs. To
avoid injury and damage, vacuum should
remain at base of stairs while in use.
• Do not handle plug or appliance with
wet hands.
Grounding
SAVE THESE INSTRUCTIONS.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Thermal fuse protection
Description of the vacuum
Your Riccar vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector.
This thermal protector is designed to protect your vacuum cleaner from overheating due to
a restriction in airflow (i.e. clogged hose, operating the vacuum without a bag). Should this
situation occur, the thermal fuse protector will safely shut off the vacuum cleaner to avoid
any potential damage.
(On-board tools
select models only)
Handle grip
On/Off switch
(Models 8920,
8925, 8955)
NOTE: To determine it was the thermal fuse protector that turned off your vacuum
cleaner, please refer to the vacuum cleaner's headlight. If the headlight is on while the motor
is off, then the thermal fuse protector did safely shut down the motor. If both the headlight
and motor are off, then there is some reason other than the thermal protector (i.e. pulled
plug) your vacuum is off.
Handle tube
Quick cord release
Power cord
Bag compartment
cover release button
Easy-carry handle
To reset the thermal fuse:
Accessory
attachment
ꢀ. Unplug the vacuum cleaner
2. Check for problem – over–filled bag, clog in hose, clogged filters, etc.
3. Correct problem
Bag compartment
cover
Telescopic wand
opening
Crevice tool
4. Locate "tripped" fuse – the small white button located on the bottom of the back side of
the main body (roughly one inch to the right of the left wheel)
5. Using a pencil, paper clip or other pointed object, push the reset button in
6. Plug vacuum cleaner in and resume use
Upholstery tool
Dusting brush
Stretch hose
Nozzle inlet
Headlight
Please contact your Authorized Riccar Retailer with any questions.
Rug/floor selector
(select models)
Furniture guard
Foot pedal release
Thermal reset button
Self adjusting nozzle
Riccar Replacement Parts
Vacuum Agitator Belt
Genuine Riccar High Flow
HEPA Vacuum Bags
Post Filter
RF89-2
2 per pkg
Models 8900, 8905,
8920, 8925
A20-R2P
2 per pkg
Cꢀ5H-6
6 per pkg
Secondary Charcoal Filter
RCFT89-2
Models 8905, 8925, 8955
Genuine Riccar Eco Pure
Vacuum Filter Bags
RF8900P-ꢀ
ꢀ per pkg
Model 8955
Cꢀ5-6
6 per pkg
RCF89-2
Models 8900, 8920
Light Bulb Xenon
A350-0000
Wedge Base, 0.9ꢀ7 amp
T 3 ꢀ/4 Xenon
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Operation
Operation
1
2
Handle adjustments
6
7
Attaching the handle
• The handle of this vacuum cleaner can be set
to one of three positions: Upright, Middle or
Low. To release the handle, step on the pedal
at the left rear corner of the vacuum cleaner
(diagram 6).
• Upright position: Handle locks in this position
for vacuum cleaner storage. The handle
should always be in an upright position when
cleaning tools are used (diagram 7).
• Middle position: This position, the front of the
nozzle can be raised by lowering the handle
in order to cross room thresholds.
• Low position: This position is used for
cleaning under furniture (diagram 8).
The cleaner and the handle are packed separately.
• After first removing the handle screw, insert
handle into the hole on top of the vacuum
cleaner. Make sure that the switch on the handle
is positioned to the front of the vacuum cleaner
(diagram ꢀ).
• Line up the small hole on the handle with the
small hole on the vacuum cleaner and insert
the screw. Make sure the screw is tightened
securely.
• Attach the power cord at the clip located on the
upper cord hook (diagram 2).
• Turn the upper cord storage hook to the upright
position and wind the power cord around the
cord storage hooks when storing the vacuum
cleaner (diagram 3).
8
3
4
How to change the vacuum bag
How to Install Hose Assembly
9
10
Genuine Riccar vacuum bags should
be used for best performance and air filtration.
Always operate the vacuum cleaner with a
vacuum bag installed.
• Install hose cuff in nozzle inlet (diagram 4).
How to Release the Power Cord
• The upper cord storage hook has a quick-
release action. To release the cord, rotate the
hook downward and the cord will drop off the
handle for immediate use (diagram 5).
• Return the hook to the upright position before
attempting to rewind the cord (diagram 2).
NOTE: If secondary or post filters need to be
replaced, see page 8 before replacing the
vacuum bag.
5
ꢀ. Remove the used vacuum bag by pulling
bag collar off the bag holder [Fig. ꢀ0]. Do
not re-use filled vacuum bags.
11
On/Off Switch
• To start the vacuum cleaner, slide the switch on
the handle to the ON position.
• To stop the vacuum cleaner, slide the switch on
the handle to the OFF position.
• Turn the vacuum off before unplugging from the
electrical outlet.
2. Attach the new vacuum bag onto the
bag holder.
3. Re-insert the tab on bottom edge of bag
compartment cover into the groove on the
bag compartment housing [Fig. ꢀꢀ]. Press it
into place and close the bag compartment
cover tightly.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Operation
Operation
CAUTION:
15
First, disconnect the vacuum cleaner from the
electrical outlet.
Replacing secondary filter
The secondary filter protects the motor from
dust and dirt. Before installing a new filter bag,
check the filter. Accumulated dirt in the dust
compartment will be collected on this filter and
may restrict motor performance, when the filter
becomes dirty (diagram ꢀ2).
12
Replacing headlight bulb
Remove the headlight bracket screw (diagram ꢀ5). Slide
bracket back and lift bracket upward and out of nozzle. To
remove the light bulb, pull straight out of socket. To install
new bulb, simply push bulb straight into socket for
a secure fit.
Cleaning secondary filter: Remove bag supporter
(some models only) by releasing the right tab on
the underside of bag supporter. Lift and rotate to
remove bag supporter. Now, remove secondary
filter from bottom of dust compartment. Replace
with new filter. Reinstall bag supporter.
Removing and reinstalling bottom plate
Removing bottom plate: To replace any of the following
parts, place vacuum cleaner in the low position by using
the handle release pedal. Then, turn the vacuum cleaner
over, exposing the underside. Remove the two screws
holding the lower plate in place. Now remove the bottom
plate.
Note: Riccar exhaust filters cannot be washed
or re-used.
Installing bottom plate: install bottom plate making sure
bottom plate hinges are in place on front of housing
(diagram ꢀ6) before securing screws.
16
Replacing post filter
Your Riccar vacuum cleaner is equipped with an
auxiliary post filter to capture fine dust particles
and purify the air before it exits the machine. It
is important to change the post filter regularly -
approximately every third filter bag change, or as
needed.
13
14
Edge cleaning feature
The edge cleaning feature provides for improved cleaning of
carpets near wall and stationary furniture.
Automatic self adjusting rug nozzle
To change the Post Filter:
Your Riccar upright vacuum cleaner is designed with
an Automatic Self Adjusting Rug Nozzle. No manual
adjustments are required. The height of the rug nozzle is
instantly and automatically adjusted to carpet pile height.
This self adjusting feature allows the rug nozzle to float
evenly over all carpet pile surfaces.
• Depress handle release pedal and move
vacuum to lower position (diagram ꢀ3).
• Remove exhaust filter by pressing the two
upper tabs and pulling filter away from vacuum
(diagram ꢀ4).
• Insert a new exhaust filter by inserting the lower
portion of the filter first and snap the upper
portion into the vacuum.
Carpet/Floor selector
(models 8900, 8925 & 8955 only)
17
Note: Post filters cannot be washed.
When vacuuming bare floors or tile, or when using
attachments, disengage the brush roll by moving the
switch located on the nozzle housing to the floor setting
(diagram ꢀ7).
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
Operation
Operation
Replacing agitator belt
(Models 8900, 8925 & 8955 only)
Replacing agitator belt
How to Replace Agitator Belt (All Other Models)
18
19
20
23
• Disconnect the vacum cleaner from the
electrical outlet.
• Disconnect the vacum cleaner from the
electrical outlet.
• Turn the unit over and remove the bottom plate as
described in the preceding section.
• Turn the unit over and remove the bottom plate as
described in the preceding section.
• Move carpet/floor selector to floor position.
24
1
• Remove the vented support fitting (diagram 23).
• Remove the vented support fitting (diagram ꢀ8).
Note the position of the support fitting before it is
removed so that it can be reinstalled properly.
• Take out the agitator and remove the worn or broken
belt from the agitator pulley and the motor drive shaft
(diagram 24).
• Rotate belt so that the linkage rod can be removed
(diagram ꢀ9). Slide linkage rod out and move the
carpet/floor selector to carpet position and let rod
rest behind brush roll compartment (diagram 20).
• Loop the new belt around the agitator pulley and the
motor drive shaft (diagram 25).
25
Motor
• Re-insert the agitator back into the housing (diagram 26).
Drive
Shaft
• Remove agitator and worn or broken belt
(diagram 2ꢀ).
• Turn the agitator by hand, making sure the belt is not
twisted and all rotating parts move smoothly (diagram 27).
Agitator Pulley
• Loop the new belt around the motor drive shaft
and the agitator pulley.
• Re-insert the vented support fitting. Be sure that the
vented support fitting is in place before fastening the
bottom plate to the two ribs at the front end of the
housing (See "How To Install Bottom Plate").
• Reinstall the agitator into the housing while making
sure that the positioning fork faces down and
straddles the support guide (diagram 22).
• Check to see if the belt is stretched, cracked or if
excessive slipping has occurred. Replace if needed.
• Reinstall linkage rod by moving carpet/floor
selector to the floor position.
26
21
• Rotate belt away from linkage rod, then install
linkage rod into brush roll.
27
• Rotate agitator pulley, making sure that the belt is
not twisted (diagram 24).
22
• Reinsert the vented support fitting. Reinstall
bottom plate (See "How to Install Bottom Plate").
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ0
ꢀꢀ
Operation
Tools
CAUTION:
28
29
On-board cleaning tools
(Models 8905, 8925 & 8955)
First, disconnect the vacuum cleaner from the
electrical outlet.
Select models are equipped with on-board cleaning tools
including 4-to-ꢀ stretch hose, 3 piece telescopic wand,
crevice tool, dusting tool, upholstery tool.
Unclogging nozzle and hose
The nozzle hose, located on the back of the vacuum
cleaner, carries the dirt from the nozzle to the filter bag. The
hose also functions as the attachment cleaning hose. If the
hose should become clogged:
• Pull out and turn the lid of the cleaning attachment
opening. Remove the clog or blockage.
• If the above step is not enough, remove hose cuff from
the nozzle inlet (diagram 28). Turn the vacuum over and
unscrew the bottom plate and remove plate (see "How
To Remove Bottom Plate"). Check nozzle inlet tube for
obstructions. Clear tube and re-install the bottom plate
(diagram 29).
• Remove hose cuff from the nozzle inlet (diagram 29).
30
31
32
33
Nozzle
Inlet
• Remove the telescopic wand from the body of the
vacuum and connect it to the hose cuff (diagram 30).
Unlock wand collars, extend wand and re-lock
wand collars.
Tube
29
Note: Wand collar locking rotation is marked with arrows
on the wand. Cleaning tools can be used with the wand
extended or compressed or the tools can be used without
the wand by connecting the tools directly to the hose cuff
(diagram 3ꢀ).
Full bag indicator light
The warning light is located on top of the bag compartment
(see diagram 30). The light will trigger if the vacuum bag
is full or if there is a clog in the vacuum cleaner. If the
light indicator turns on, check the vacuum bag. If it is not
full, check the vacuum cleaner for clogs by inspecting
the agitator area (see “Removing and re-installing bottom
plate”), hose and/or attachment inlet.
28
• Select the proper tool for your cleaning situation and
connect the tool to the end of the wand or cuff (diagram
32). NOTE: Tools store conveniently in vacuum body by
snap-fit.
Suction control dial
(Models 8905, 8925 & 8955)
The lid on the attachment port is a suction control dial
(Diagram 33). This feature is useful when less suction is
needed, for example, to clean drapes, throw rugs, etc. To
use, simply turn the dial to reduce the suction to desired
level. Close the dial for normal vacuum operation.
Please disregard the indicator light during attachment
cleaning. The light is designed to indicate air flow restriction
during carpet cleaning. When using cleaning attachments,
the indicator will light periodically due to normal attachment
air flow restrictions.
Note: When using an optional attachment hose with the
suction control dial feature, do NOT insert the attachment
hose into the attachment port. Doing so will bypass the
suction control dial features. Instead, attach the optional
hose to the hose cuff (located at the bottom back side of
the vacuum). Simply insert the hose cuff from the vacuum
cleaner into the cuff of the attachment hose. The hose cuff
is designed to fit into the optional attachment hose, thereby
allowing use of the suction control dial.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ2
ꢀ3
Tools
Warranty
Optional cleaning tools
What is Covered:
This warranty covers any defects in material and workmanship in your new
Riccar vacuum.
All Riccar upright vacuum cleaners offer an attachment port that enables you to insert
optional cleaning tools (available through your Riccar Retailer). Should you have carpeted
stairs, for example, it is highly recommended to use one of the two kits pictured, since each
offers either a ꢀ2 - or ꢀ5 - foot hose for safe stair cleaning. These kits are effective cleaning
tools to address some of the hard to reach areas of your home or car. Talk to your Riccar
Retailer to see which tools might be beneficial for your home.
How Long Coverage Lasts:
Warranty coverage for Riccar 8900 Premier Series household model vacuums
lasts five years and one year for 8900 Premier Series commercial model vacuums.
Household models used commercially are only warranted for 90 days.
For models without on-board tools
For models with on-board tools
Deluxe Attachment Set (diagram 34)
Attachment Set (diagram 35)
ꢀ. ꢀ2-foot hose
2. Curved wand
3. Extension wand (2 pieces)
4. Dusting brush
5. Crevice tool
6. Upholstery tool
7. Upholstery brush insert
8. Deluxe floor brush
ꢀ. ꢀ5-foot hose
2. Curved wand
3. Deluxe floor brush
What is Not Covered:
• Damage to the vacuum which occurs from neglect, abuse, alterations, accident,
misuse or improper maintenance.
• Normal replacement items: agitator brushes, belts, light bulbs, disposable bags
and disposable filters.
What Riccar Will Do:
This warranty provides, at no cost to you, all labor and parts to place this vacuum
in correct operating condition during the warranted period.
Diagram 35
How to Get Service:
Warranty service can only be obtained by presenting the vacuum to an Authorized
Riccar Retailer. A proof-of-purchase and product serial number will be required
before service is rendered. To locate your nearest Riccar Retailer, please call
Diagram 34
ꢀ. How to connect the hose assembly to the
vacuum cleaner:
Pull out and open the suction control dial by turning the
lid located on the back of the vacuum cleaner. Insert the
soft, rubber end of the hose assembly into the cleaning
attachment opening. Push in while twisting the hose end to
ensure the hose is fastened securely (diagram 36).
2. How to connect the tool: You can connect any of the
cleaning tools to the end of the extension wand(s) or
curved wand and twist for a secure fit. To remove the
cleaning tool from the extension wand(s) or curved wand,
simply twist and pull apart.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER
WARRANTIESWHETHERWRITTEN,ORAL,EXPRESSEDORIMPLIED,(INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE). THIS WARRANTY DISCLAIMS LIABILITY FOR INCIDENTAL, OR
CONSEQUENTIAL DAMAGES.
Diagram 36
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
WARNING: There is no way to turn this vacuum’s brushroll off. Therefore, when using the cleaning
tools it is important to keep your Riccar vacuum from running in the same spot for a period of time, as
carpet or flooring damage could result. If you need to keep the vacuum in the same spot for a period
of time, such as at the base of the stairs when cleaning the stairs, place something, like a flattened
cardboard box, under the vacuum to prevent damage to the floor.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ4
ꢀ5
Owner’s information (keep this for your records)
Notes
The model and serial number of this product may be found on the back side of the unit. You
should note the model and serial number of your unit in the spaces provided below, and
retain this book as a permanent record of your purchase.
Date of purchase ____________________________________________________
Serial number _______________________________________________________
Model number ______________________________________________________
Purchased from:
Store name _______________________________________________________
Address
City, State, Zip ______________________________________________________
Telephone _______________________________________________________
_______________________________________________________
Your Riccar vacuum cleaner is a product of high quality materials and superior workmanship.
Your new Riccar vacuum cleaner will work on carpets, floors and for many other cleaning
needs in your home. We urge you to read these operating instructions carefully before you
use this vacuum cleaner, in order to obtain the full performance and satisfaction it can
offer you.
For Best Performance
•
Before you plug in your Riccar vacuum cleaner, make sure that the voltage indicated
on the rating plate (located near the bottom on the back of the vacuum) is the same
as your local supply.
•
•
•
Keep machine and all accessories clean and in good operating condition.
Store machine carefully in a dry area.
Always use genuine Riccar vacuum bags and filters. Use of other products may result
in poor cleaning or filtration performance. Riccar filtration products are designed for
maximum performance.
•
•
•
Have machine checked periodically by an Authorized Riccar Vacuum Service Center.
Use only Riccar Vacuum Cleaner Authorized Service Centers for parts and service.
For optimum cleaning performance and safety, follow your Owner’s Manual and keep it
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ6
ꢀ7
|