VPAP™ ST
VPAP™ S
POSITIVE AIRWAY PRESSURE DEVICE
Welcome Guide
English
Download from Www.Somanuals.com. All Manuals Search And Download.
3
2
5
4
1
Setup
1. Connect the DC plug of the power supply unit to the rear of the VPAP.
2. Connect the power cord to the power supply unit.
3. Plug the other end of the power cord into the power outlet.
4. Connect one end of the air tubing firmly onto the air outlet.
5. Connect the assembled mask system to the free end of the air tubing.
Notes:
•
•
For more information on assembling your mask see your mask user guide.
under Service & Support.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD screen
Displays the menus,
treatment screens and
reminders.
Start/Stop button
Starts or stops
treatment.
Key:
Home
Humidity level
Ramp
Setup menu
Allows you to
make changes
to settings or
exit from the
menu.
Heated tube
Climate
Control
Info menu
Allows you to
view your sleep
statistics or exit
from the menu.
Start/Stop
Push dial
Push dial
Turning the dial
allows you to
Setup menu
Info menu
scroll through the
menu and change
settings. Pushing the
dial allows you to
enter into a menu and
confirm your choice.
VPAP basics
The control panel of your VPAP device includes
an LCD screen as well as a Start/Stop button,
Push dial and the Info and Setup menu keys.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Adjusting ramp time
Designed to make the beginning of treatment more comfortable, ramp time is the period during which
the pressure increases from a low start pressure to the treatment pressure. To adjust your ramp time:
2. Press
.
1. From your HOME
screen, turn
3. Turn
until
4. Press
confirm your
choice.
to
The selection is
highlighted in
orange.
the ramp time
you require is
displayed.
until the RAMP
screen is displayed
in blue.
Using mask-fit
You can use mask-fit to help you fit your mask properly. This feature delivers treatment pressure for a
three-minute period, prior to starting treatment, during which you can check and adjust your mask-fit to
minimise leaks.
1. Fit your mask as described in the mask user guide.
2. From your home screen, push and hold
for three seconds. One of the following MASK FIT
screens is displayed:
3. If necessary, adjust your mask, mask cushion and headgear until you have a Good mask-fit.
After three minutes, the pressure reverts to the set pressure and treatment will begin. You can end
mask-fit at any time by pressing
.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the mask type
To select your type of mask:
1. Press . The SETTINGS
2. Turn
until Mask is
3. Press
.
screen is displayed.
displayed in blue.
The selection is highlighted
in orange.
4. Turn
until the mask
5. Press
to confirm your
6. Push
to return to the
setting that you require is
displayed.
choice.
HOME screen.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Getting started
1. Make sure the power is connected.
2. Adjust the ramp time if required.
3. Fit your mask as described in your mask user guide.
4. To start therapy, simply breathe into the mask and/or press
.
5. Lie down and arrange the air tubing so that it is free to move if you
turn in your sleep.
6. To stop treatment at any time, remove your mask and/or press
.
Notes:
•
If your clinician has enabled SmartStart your device will start
automatically when you breathe into the mask and stop automatically
when you remove the mask.
•
If power is interrupted during treatment, the device automatically
restarts therapy when power is restored.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the treatment screens
Depending on how the system has been configured, you will see one of the following example screens
(shown in the ST mode) once therapy has started:
9 H5i humidifier
9 H5i humidifier
9 H5i humidifier
9 ClimateLine or ClimateLineMAX 9 ClimateLine or ClimateLineMAX
heated air tube
9 Climate Control – Auto
heated air tube
9 Climate Control – Manual
9 Standard VPAP without
9 Oximetry data via the
optional accessories
oximeter adapter
In S and ST modes, the fixed lines on the pressure bar indicate the expiratory and inspiratory pressures.
In CPAP mode, only a set pressure is shown. While the treatment is ramping (indicated by an orange
ramp icon below the pressure bar), the pressure values appear in orange. When a set pressure is reached
these values are displayed in white.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
English
To toggle between treatment screens 1 and 2, press
from your HOME screen.
9 Treatment with device trigger 9 Treatment with spontaneous
(Timed) and cycle (Timed,
Ti Max orTi Min) breath
indicators
trigger and cycled breaths
Viewing the Info menu
The Info menu has a series of screens showing your sleep quality, sleep report and service information.
To view the Info menu, push
from your HOME screen.
9 In the Sleep Quality screen,
you can always view your
usage hours during the last
session and if enabled by
your clinician, data on mask-
fit and AHI is displayed.
9 In the Sleep Report, only the 9 In the Service information,
period can be changed—
other values are for display
only.
the device run hours
(includes warm-up/cool-down
times for the humidifier) and
the software identifications
are displayed.
To return to the HOME screen, push
.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and maintenance
Refer to your mask and humidifier user guides for detailed instructions regarding the care of these
devices.
Daily
Remove the air tubing by pulling on the finger grips on the cuff. Hang it in a clean, dry place until next
use.
Weekly
1. Remove the air tubing from the VPAP device and the mask.
2. Wash the air tubing in warm water using mild detergent.
3. Rinse thoroughly, hang, and allow to dry.
4. Before next use, reconnect the air tubing to the air outlet and mask.
Monthly
1. Wipe the exterior of the VPAP with a damp cloth and mild detergent.
2. Check the air filter for holes and blockage by dirt or dust. Replace the air filter if necessary.
Replacing the air filter
Replace the air filter every six months (or more often if necessary).
1. Remove the air filter cover from the back of the VPAP device.
2. Remove and discard the old air filter.
3. Insert a new ResMed air filter ensuring that it is
sitting flat in the air filter cover.
4. Replace the air filter cover.
Air filter cover
Air filter
9
Download from Www.Somanuals.com. All Manuals Search And Download.
English
SD card
An SD card has been supplied
to gather therapy data from
your VPAP device and provide
settings updates from your
clinician. When instructed to do
so, disconnect the VPAP device
from the power outlet, remove
your SD card, insert it in the
protective folder and send it to
your clinician.
Removing the card
1. Push in the SD card to
release it.
2. Remove the card.
3. Insert the card into the
protective folder.
4. Send the protective folder
back to your clinician as
instructed.
For more information on
removing and inserting your
card refer to the S9 SD Card
Protective Folder provided with
your device. Please retain the
S9 SD Card Protective Folder
for future use.
Notes:
•
ForTroubleshooting information
refer to the Information Guide.
For more product information
•
1.
2.
3.
4.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
368698/1 2012-02
S9 VPAP ST / S9 VPAP S
WELCOME
EUR1
Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center
Boulevard San Diego CA 92123 USA.
ResMed locations worldwide.
S9 VPAP, H5i, ClimateLine, SlimLine and SmartStart are trademarks of ResMed Ltd and S9, ClimateLine, SmartStart and VPAP are registered
in U.S. Patent and Trademark Office.
© 2012 ResMed Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|