HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
848-D3Z-93A0 (005)
U
S
OWNER'S/OPERATOR'S
MANUAL
HEDGE TRIMMER
HTZ2460
HTZ2460L
CHTZ2460
CHTZ2460L
WARNING
The engine exhaust from this
product contains chemicals
known to the State of California to
cause cancer, birth defects or
other reproductive harm.
WARNING
Before using our products,
please read this manual carefully
to understand the proper use of
your unit.
This spark ignition system complies with
the Canadian standard ICES-002.
US-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
1. Parts location
U
S
1. Front handle
2. Rear handle
3. Ignition switch
4. Throttle lever
5. Safety lock
6. Blade
9. Starter knob
10. Primer pump
11. Fuel tank
12. Fuel tank cap
13. Choke lever
14. Air cleaner cover
15. Spark plug cap
7. Gear case
8. Spark arrester
2. Specifications
Model
Type
HTZ2460
HTZ2460L
CHTZ2460
Reciprocating
double-sided dual blades
CHTZ2460L
Reciprocating
single-sided dual blades
Dry weight
Blade size
Blade pitch
Transmission
Reduction ratio
5.8(kg)/12.6(lbs)
750(mm)/30(in)
35(mm)/1.38(in)
6.4(kg)/14.1(lbs)
1080(mm)/42.5(in)
34(mm)/1.34(in)
5.8(kg)/12.8(lbs)
600(mm)/24(in)
6.0(kg)/13.2(lbs)
750(mm)/30(in)
35(mm)/1.38(in)
Centrifugal clutch, Cam-crank
4.5
Air-cooled 2-stroke gasoline
GZ23N
Engine
Type
Mode
3
Displacement
Max. output
Idle speed
Fuel
23.6(cm )/1.44(cu-in)
-1
1.15Hp(0.85kW)/8000min (rpm)
-1
3000 200/min (rpm)
:
mixture(Gasoline 50 Oil 1)(when using RedMax genuine oil)
Carburetor
Spark plug
Walbro Diaphragm type
NGK CMR7H
Fuel tank capacity
Durability period
0.47(litter)/15.9(fl.oz)
300(hrs.)
Specifications are subject to change without notice.
US-3
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
3. Warning labels on the machine
(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Handling this machine improperly could result in
accidents causing serious injury or death. Read this
manual carefully and practice using the hedge-trimmer
until you are fully acquainted with all operations and have
learned to use it correctly.
(4) This is extremely sharp and can easily cause cuts.
IMPORTANT
If warning label peel off or become soiled and impossible to read,
you should contact the dealer from which you purchased the
product to order new labels and affix them in the required
location(s).
WARNING
Never modify your machine.
We won’t warrant the machine, if you use the remodeled
hedge-trimmer or you don’t observe the proper usage written
in the manual.
4. Symbols on the machine
For safe operation and maintenance, symbols
■ EMISSION CONTROL
are carved in relief on the machine. According
to these indications, please be careful not to
take a mistake.
An emission control label is located on the engine.
EMISSION CONTROL INFORMATION
THIS ENGINE MEETS U.S. EPA AND CALI-
1
FORNIA EXH / EVP REGS FOR 2010* S.O.R.E.
(a) The port to refuel the "MIX GASOLINE"
Position:
FUEL TANK CAP
2
ENGINE FAMILY : AHQZS.0244XY* DISPL.: 24cc
3
EMISSION CONTROL SYSTEM : EXH;EM/EVP;SP*
COMPLIANCE PERIOD : 300 HOURS
REFER TO OPERATOR'S MANUAL FOR MAINTE-
NANCE, SPECIFICATIONS AND ADJUSTMENTS.
MANUFACTURED:
(b) The direction to close the choke
Position:
USE JASO FD OR ISO L-EGD GRADE 50:1 OIL
AIR CLEANER COVER
*1: The year will be changed every year of manufacturing.
*2: The initial will be changed every year of manufacturing.
*3: SP : Sealed tank made of HDPE or PE.
(c) The direction to open the choke
Position:
AIR CLEANER COVER
US-4
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
5. For safe operation
other times when your field of vision
might be limited and it would be difficult
to gain a clear view of the working area.
c. During rain, during storms at times of
strong or gale-force winds, or at any
other times when weather conditions
might make it unsafe to use the
product.
1. THIS MACHINE CAN CAUSE
SERIOUS INJURIES. Read this manual
carefully until you completely
understand and follow all safety and
operating instructions. Also, know how
to stop the machine quickly in an
emergency.
2. Keep this manual handy so that you
may refer to it later whenever any
questions arise. Also note, if you have
any questions which cannot be
answered herein, contact the dealer
from whom you purchased the product.
3. Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this
product.
U
S
■ WORKING PLAN
1. You should never use the product when
under the influence of alcohol, when
suffering from exhaustion or lack of sleep,
when suffering from drowsiness as a result
of having taken cold medicine or at any
other time when a possibility exists that
your judgment might be impaired or that
you might not be able to operate the
product properly and in a safe manner.
2. When planning your work schedule, allow
plenty of time to rest. Limit the amount of
time over which the product is to be used
continuously to somewhere around 30 ~ 40
minutes per session, and take 10 ~ 20
minutes of rest between work sessions.
Also try to keep the total amount of work
performed in a single day under 2 hours or
less.
4. Never allow children or anyone unable
to fully understand the directions given
in the manual to use the machine.
■ WORKING CONDITION
1. When using the product, you should wear
proper clothing and protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
WARNING
1. If you don’t observe the working time,
or working manner (See “USING THE
PRODUCT”), Repetitive Stress Injury
(RSI) could occur.
If you feel discomfort, redness and
swelling of your fingers or any other
part of your body, see a doctor before
getting worse.
2. To avoid noise complaints, in general,
operate product between 8 a.m. and 5
p.m. on weekdays and 9 a.m. to 5 p.m.
on weekends.
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area
(rope, warning signs)
(5) Whistle (for collaboration or emergency)
(6) Hatchet or saw (for removal of
obstacles)
(7) First-aid kit
NOTE
3. Do not wear loose clothing, jewelry, short
trousers, sandals, or go barefoot. Do not
wear anything which might be caught by a
moving part of the unit. Secure hair so it is
above shoulder length.
Check and follow the local regulations as to
sound level and hours of operations for the
product.
■ BEFORE STARTING THE ENGINE
1. The area within a perimeter of 15 m (50 ft)
of the person using the product should be
considered a hazardous area into which no
one should enter. If necessary, yellow
warning rope, warning signs should be
placed around the perimeter of the area.
When work is to be performed
■ WORKING CIRCUMSTANCE
1. Never start the engine inside a closed
room or building. Exhaust gases contain
dangerous carbon monoxide.
2. Never use the product,
a. when the ground is slippery or when
you can’t maintain a steady posture.
b. At night, at times of heavy fog, or at any
simultaneously by two or more persons,
US-5
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
5. For safe operation
care should also be taken to constantly
manufacturer. And use only for tasks
explained in the manual.
look around or otherwise check for the
presence and locations of other people
working so as to maintain a distance
between each person sufficient to ensure
safety.
2. Check the condition of working area to
avoid any accident by hitting hidden
obstacles such as stumps, stones, cans, or
broken glass.
1. Grip the handles firmly with both hands
using your whole hand. Place your feet
slightly apart (slightly further apart than the
width of your shoulders) so that your
weight is distributed evenly across both
legs, and always be sure to maintain a
steady, even posture while working.
2. Maintain the speed of the engine at the
level required to perform cutting work, and
never raise the speed of the engine above
the level necessary.
IMPORTANT
Remove any obstacle before beginning work.
3. If the unit starts to shake or vibrate, turn off
the engine and check the whole unit. Do
not use it until the trouble has been
properly corrected.
4. Keep all parts of your body away from
moving cutting attachment and hot
surfaces.
3. Inspect the entire unit for loose fasteners
and fuel leakage. Make sure that the
cutting attachment is properly installed and
securely fastened.
■ STARTING THE ENGINE
1. Keep bystanders especially children, and
animals at least 15 m (50 ft) away from the
operating point. If you are approached,
immediately stop the engine.
2. The product is equipped with a centrifugal
clutch mechanism, so the cutting
attachment begins to move as soon as the
engine is started by putting the throttle into
the start position. When starting the
engine, place the product onto the ground
in a flat clear area and hold it firmly in
place so as to ensure that neither the
cutting part nor the throttle come into
contact with any obstacle when the engine
starts.
5. Never touch the muffler, spark plug, or
other metallic parts of the engine while the
engine is in operation or immediately after
shutting down the engine. Doing so could
result in serious burns or electrical shock.
6. While operating the machine be always
sure of a safe and secure operating
position especially when using steps or a
ladder.
• IF SOMEONE COMES
1. Guard against hazardous situations at all
times. Warn adults to keep pets and
children away from the area. Be careful if
you are approached. Injury may result from
flying debris.
2. If someone calls out or otherwise interrupts
you while working, always be sure to turn
off the engine before turning around.
WARNING
• Never place the throttle into the high-
speed position when starting the
engine.
■ MAINTENANCE
• Never start the engine at the cutting
attachment side.
1. In order to maintain your product in proper
working order, perform the maintenance
and checking operations described in the
manual at regular intervals.
2. Always be sure to turn off the engine
before performing any maintenance,
checking procedures or working on the
machine.
3. After starting the engine, check to make
sure that the cutting attachment stops
moving when the throttle is moved fully
back to its original position. If it continues
to move even after the throttle has been
moved fully back, turn off the engine and
take the unit to your authorized RedMax
servicing dealer for repair.
(1) Check ok!
WARNING
■ USING THE PRODUCT
The metallic parts reach high
temperatures immediately after stopping
the engine.
IMPORTANT
Cut only materials recommended by the
US-6
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
5. For safe operation
3. When replacing the cutting attachment or
If doing so, fuel might leak from the tank
during transport.
any other part, or when replacing the oil or
any lubricant, always be sure to use only
RedMax products or products which
have been certified by RedMax for use
with the RedMax product.
U
S
4. In the event that any part must be replaced
or any maintenance or repair work not
described in this manual must be
performed, please contact a representative
from the store nearest RedMax authorized
servicing dealer for assistance.
5. Do not use any accessory or attachment
other than those bearing the RedMax mark
and recommended for the unit.
6. Under no circumstances should you ever
take apart the product or alter it in any
way. Doing so might result in the product
becoming damaged during operation or the
product becoming unable to operate
properly.
■ HANDLING FUEL
1. The engine of the RedMax product is
designed to run on a mixed fuel, which
contains highly flammable gasoline. Never
store cans of fuel or refill the tank of the
unit in any place where there is a boiler,
stove, wood fire, electrical sparks, welding
sparks, or any other source of heat or fire
which might ignite the fuel.
2. Never smoke while operating the unit or
refilling its fuel tank.
3. When refilling the tank, always turn off the
engine and allow it to cool down. Take a
careful look around to make sure that there
are no sparks or open flames anywhere
nearby before refueling.
(1) Refill after cooling the engine.
4. Wipe spilled fuel completely using a dry
rag if any fuel spillage occurs during
refueling.
5. After refueling, screw the fuel cap back
tightly onto the fuel tank and then carry the
unit to a spot 3 m or more away from
where it was refueled before turning on the
engine.
6. Do not inhale fuel fumes as they are toxic.
■ TRANSPORTATION
1. When hand-carrying the product, cover
over the cutting part if necessary, lift up the
product and carry it paying attention to the
blade.
2. Never transport the product over rough
roads over long distances by vehicle
without removing all fuel from the fuel tank.
US-7
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
6. Fuel
FUEL
lines or fuel tank of the engine.
WARNING
NOTE
• Gasoline is very flammable. Avoid smoking or bringing any
flame or sparks near fuel. Make sure to stop the engine and
allow it cool before refueling the unit. Select outdoor bare
ground for fueling and move at least 10 ft (3 m) away from
the fueling point before starting the engine.
• Failures caused by operating engines on gasoline with octane
rating lower than 89 are not covered by the RedMax Two-
Stroke engine warranty.
WARNING
• Alternative Fuels (Not Gasoline)
Alternative fuels, such as E-15 (15% ethanol), E-20 (20%
ethanol), E-85 (85% ethanol) are NOT classified as gasoline
and are NOT approved for use in RedMax 2-stroke gasoline
engines. Use of alternative fuels will cause major engine
performance and durability problems such as: improper
clutch engagements, overheating, vapor lock, power loss,
lubrication deficiency, deterioration of fuel lines, gaskets
and internal carburetor components, etc... Alternative fuels
cause high moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
■ GASOLINE REQUIREMENTS
• All 2-Stroke RedMax Products are powered by RedMax
Professional-Commercial Duty, Hi-Performance, Hi-RPM, Air
Cooled 2-Stroke engines.
RedMax – Hi-Performance 2-stroke engines produce higher HP
outputs as compared to standard Home Owner Duty or Light
Commercial Duty production engines offered by most
manufacturers.
• Exhaust emission are controlled by the fundamental engine
parameters and components (eq., carburation, ignition timing
and port timing) without addition of any major hardware or the
introduction of an inert material during combustion.
• The RedMax Engines are registered and certified with CARB
(California Air Resources Board) and EPA (Environmental
Protection Agency) to operate on CLEAN Mid-grade 89 octane
or Premium, unleaded (lead-free) gasoline and RedMax Air-
Cooled "Max Life", Synthetic blend Premium two-stroke engine
oil mixed at 50:1 ratio.
■ OIL REQUIREMENTS
• Use only RedMax "Max Life", Synthetic blend Premium Air-
Cooled two-stroke engine oil or oil certified to ISO-L-EGD
(ISO/CD1378) standard AND one that is JASO-FD registered.
RedMax Air-Cooled "Max Life", Synthetic blend Premium two
stroke engine oil and ISO-L-EGD (ISO/CD1378) AND JASO-FD
oils are fully compatible with gasoline's containing 10% Ethanol.
RedMax Air-Cooled "Max Life", Synthetic blend Premium two
stroke engine oil and ISO-L-EGD (ISO/CD1378) AND JASO-FD
oils are Universal and should be mixed at 50:1 ratio for all 2
stroke air cooled engines sold in the past regardless of mixing
ratios specified in those manuals.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health and the
environment.
• If the oil is registered with JASO, the JASO Logo with FD and
registration number will be displayed on the container. The
highest JASO rating is "FD", which equals the ISO-L-EGD
rating. Lower ratings are "FC", "FB", and "FA".
• This Hi-Performance Air Cooled 2-stroke Engine requires the
[ R+M ]
use of Minimum 89 Octane
(Mid grade or Premium)
2
clean gasoline. Gasoline may contain maximum of 10% Ethanol
(grain alcohol) or up to 15% MTBE (Methyl tertiary-butyl ether).
Gasoline containing Methanol (Wood Alcohol) is NOT
approved.
NOTE
• Engine problems due to inadequate lubrication caused by
failure to use ISO-L-EGD certified and JASO FD registered oil
such as "MaxLife", RedMax Synthetic blend Premium 2-stroke
oil WILL VOID THE REDMAX TWO-STROKE ENGINE
WARRANTY.
• IF octane rating of the Mid Grade gasoline in your area is lower
than 89 Octane use Premium Unleaded Gasoline. The majority
of all 2-stroke engine manufacturers in the USA and Canada
recommend using gasoline with 89 Octane or higher.
WARNING
WARNING
• Gasoline with an octane rating lower than 89 will greatly
increase the engines operating temperature. Low octane
gasoline will cause detonation (knock) resulting in piston
seizures and major internal engine components damage.
• Poor quality gasolines or oils may damage sealing rings, fuel
• Do not use NMMA (National Marine Manufacturers
Association), BIA (Boating Industry Association), and TCW (two
cycle water cooled) oils designed for MoPeds or Outboard,
water cooled Marine Engines. Do not use API (American
Petroleum Institute), TC (Two Cycle) labeled oils. The API-TC
US-8
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
6. Fuel
test standard has been discontinued by API in 1995 and it no
longer exists.
WARNING
1. Select flat and bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fueling point
before starting the engine.
3. Stop the engine before refueling the unit. At that time, be
sure to sufficiently agitate the mixed gasoline in the
container.
IMPORTANT
U
S
• Gasoline/Oil mixture Storage Recommendations
Store your gasoline or gasoline/oil mixture in a cool dry area in
a tightly sealed approved container to limit the entry of moisture
and additional air (oxygen). Moisture and air cause the
development of varnish and gum, making the fuel stale. Stored
gasoline and gasoline/oil mixture ages and loses its octane
rating and volatility. Do not mix more gasoline/oil than you
intend to use in 30 days, and 60 days when fuel stabilizer is
added. RedMax Air-Cooled "Max Life" Synthetic blend
Premium two-stroke engine oil "Contains fuel stabilizer" and
will automatically extend your gasoline/oil mixture life up to 60
days.
■ FOR YOUR ENGINE LIFE, AVOID
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe
damage to the internal engine parts very quickly.
2. GASOHOL – It can cause deterioration of rubber and/or plastic
parts and disruption of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug
fouling, exhaust port blocking, or piston ring seizure.
4. Mixed fuels which have been left unused for a period of
one month or more may clog the carburetor and result in the
engine failing to operate properly.
5. In the case of storing the product for a long period of time,
clean the fuel tank after rendering it empty. Next, Start the
engine and run the carburetor dry residual fuel.
6. In the case of scrapping the used mixed oil container, scrap it
only at an authorized depository site.
■ HOW TO MIX FUEL
RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(when using RedMax Air-Cooled "Max
Life")
50:1 MIXING CHART
NOTE
GASOLINE
gal.
1
2
3
4
5
• As for details of quality assurance, read the description in the
section Limited Warranty carefully. Moreover, normal wear and
change in product with no functional influence are not covered
by the warranty. Also, be careful that, if the usage in the
instruction manual is not observed as to the mixed gasoline,
type of oil or fuel to be used. described therein, it may not be
covered by the warranty.
2-CYCLE OIL fl.oz
2.6
5.2
7.8 10.4 13
GASOLINE
liter
ml
1
2
3
4
5
2-CYCLE OIL
20
40
60
80
100
WARNING
• Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be mixed.
2. Put some of the gasoline into a clean, approved fuel container.
3. Pour in all of the oil and agitate well for 10seconds.
4. Pour in the rest of gasoline and agitate again for at least one
minute. As some oils may be difficult to agitate depending on oil
ingredients, sufficient agitation is necessary. Be careful that, if
the agitation is insufficient, there is an increased danger of early
piston seizure due to abnormally lean mixture.
5. Place a clear indication on the outside of the container to avoid
mixing up with gasoline or other containers that dont contain oil.
6. Indicate the contents on outside of container for easy
identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a clean
surface.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel spillage
around the unit.
US-9
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
7. Operation
■ STARTING ENGINE
pulling the rope, or remove the spark
plug and dry it.
WARNING
■ STOPPING ENGINE (OP3)
1. Release the throttle lever and run the
engine for a half minute.
• The cutting head will start moving
upon the engine starts.
2. Shift the ignition switch to the “STOP”
position.
1. Feed fuel into the fuel tank and tighten
the cap securely.
OP1
2. Rest the unit on a flat, firm place. Keep
the cutting head off the ground and
clear of surrounding objects as it will
start moving upon starting of the
engine.
IMPORTANT
• Except for an emergency, avoid
stopping the engine while pulling the
throttle lever.
3. Push the primer pump several times
until overflown fuel flows out in the
clear tube. (OP1)
4. When the engine is cool, move the
choke lever to the closed position.
(OP2)
NOTE
OP2
• If the engine won't stop when setting
the ignition switch to the stop position,
close the choke lever and stop the
engine.
(1) primer pump
(2) choke lever
(3) close
In this case, please repair the machine
at your nearest servicing dealer.
(4) open
■ RUNNING IN THE ENGINE
(5) ignition switch
(6) RUN
(7) STOP
IMPORTANT
OP3
(8) throttle lever
• During the first 20 working hours, do
not use the hedge-trimmer at maximum
power for long periods.
5. Set the ignition switch to the “RUN”
position. Release the throttle lever and
make sure it is fully back. (OP3)
6. While holding the unit firmly, pull out
the starter rope quickly until engine
fires. (OP4)
OP5
■ ADJUSTING IDLING SPEED
• Before adjusting the carburetor, clean
the air filter and warm up the engine.
(OP5)
(1) air filter
IMPORTANT
• Avoid pulling the rope to its end or
returning it by releasing the knob. Such
actions can cause starter failures.
• Idle screw is adjusted in order to
ensure a good safety margin between
idle running and clutch engagement.
(OP6)
OP6
OP4
7. Move the choke lever to the open
position. And pull out the starter rope
quickly to restart engine.
8. Allow the engine to warm up for a
several minutes before starting
opertion.
[HTZ2460]
[HTZ2460L]
(1) Idle screw
WARNING
• With the engine idling (3000 rpm),
the blade should not move. We
recommend that you have the dealer
or an authorised mechanic carry out
any carburetor adjustments.
NOTE
[CHTZ2460]
[CHTZ2460L]
1. When restarting the engine
immediately after stopping it, leave the
choke open.
2. Overchoking can make the engine hard
to start due to excess fuel. When the
engine failed to start after several
attempts, open the choke and repeat
WARNING
• Weather conditions and altitude may
effect carburation.
US-10
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
7. Operation
• Do not allow anyone to stay close to
the hedge-trimmer while working or
while adjusting the carburetor.
Horizontal cut:
OP11
• In order to get the best cutting results,
slightly tilt the blade (5°–10°) towards
the cutting direction (OP11, OP12).
Cut slowly, specially with thick hedges.
■ HOW TO USE
U
S
OP7
HANDLE (CHTZ2460/CHTZ2460L only)
To reduce fatigue when trimming hedges,
the handle can be swivelled through 90°
to the left or right. (OP7, OP8).
Do not press the throttle during this
operation !
WARNING
Always follow the safety precautions.
• The hedge-trimmer must only be
used to trim hedges or small
bushes. It is forbidden to cut other
types of material. Do not use the
hedge-trimmer as a lever to lift,
move or break objects, nor lock it on
fixed supports. It is forbidden to
apply tools or applications that are
not the ones indicated by the
manufacturer onto the hedge-
trimmer’s power take-off. Do not use
it for pruning trees or cutting grass.
Proceed as follows:
1. Free the handle by pressing the locking
lever; (OP7)
2. Turn the handle until the locking lever
clicks into place;
3. When the handle is locked in its new
position, you can apply the throttle
again.
OP8
OP12
(1) handle
(2) locking lever
• Use only as much throttle as is needed
to do the job. Excessive engine speed
is unnecessary.
• Avoid cutting thick branches, for which
will damage the blades and shorten the
life of drive systems.
You can swivel the handle even with the
engine idling because the hedge-trimmer
is equipped with a blade brake that
maintains the blades at a standstill.
• Always keep your body to the
carburetor side of your trimmer, never
on the muffler side.
• When a new machine is first operated,
in the first few minutes grease may
come out of the gear case. But, since
this is excess grease, there is no cause
for alarm. Just wipe it off with the
engine stopped for next use.
■ HEDGE TRIMMING TECHNIQUES
Trim sides of a hedge first, and then the
top.
OP9
Vertical cut:
• With the single-sided blade hedge-
trimmer, model HTZ2460/HTZ2460L
always cut from the bottom up (OP9).
• Always remember that the TIP of the
line does cutting. You will achieve
better results by not crowding the line
into the cutting area. Allow the unit to
trim at its own pace.
OP10
• With the 2-sided blade model
CHTZ2460/CHTZ2460L use an arcing
cut from the bottom upwards, then
downwards to use both sides of the
blades (OP10).
US-11
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
8. Maintenance
Maintenance, replacement, or repair of the emission control device and
systems may be performed by any non-road engine repair establishment or
individual.
■ MAINTENANCE CHART
Every Every Every
25
50
Before hours hours hours
100
System/components
Procedure
Note
use
after
after
after
fuel leaks, fuel spillage
wipe out
✔
✔
fuel tank, air filter, fuel filter
inspect/clean
see adjusting
idling speed
clean and readjust
plug gap
✔
replace, if necessary
replace carburetor
if necessary
idle adjusting screw
✔
GAP : .026 in (0.65 mm)
replace, if necessary
spark plug
✔
cylinder fins, intake air cooling vent
clean
✔
muffler, spark arrester, cylinder exhaust port clean
✔
✔
throttle lever, ignition switch
check operation
✔
✔
replace if
cutting parts
something’s wrong
grease
gear case
✔
screws/nuts/bolts
debris guard
tighten/replace
make sure to attach
✔
✔
not adjusting screws
• REPLACEMENT PLUG IS NGK
CMR7H OR CHAMPION RZ7C.
MA3
WARNING
• Make sure that the engine has
stopped and is cool before
performing any service to the
machine. Contact with moving
cutting head or hot muffler may
result in a personal injury.
IMPORTANT
• Note that using any spark plug other
than those designated may result in the
engine failing to operate properly or in
the engine becoming overheated and
damaged.
• To install the spark plug, first turn the
plug until it is finger tight, then tighten it
a quarter turn more with a socket
wrench.
.026 in
0.65 mm
■ AIR FILTER
MA1
• The air filter, if clogged, will reduce the
engine performance. Check and clean
the filter element. If the element is
broken or clogged, replace with a new
one. (MA1)
TIGHTENING TORQUE:
87~121 in-lbs
(1) air filter
(9.8~13.7 N.m.)
■ INTAKE AIR COOLING VENT
■ FUEL FILTER
MA2
• When the engine runs short of fuel
supply, check the fuel cap and the fuel
filter for blockage. (MA2)
WARNING
• Never touch the cylinder, muffler, or
spark plugs with your bare hands
immediately after stopping the
engine. The engine can become very
hot when in operation, and doing so
could result in severe burns.
(1) fuel filter
MA4
(1)
■ SPARK PLUG
• Starting failure and mis-firing are often
caused by a fouled spark plug. Clean
the spark plug and check that the plug
gap is in the correct range. For a
replacement plug, use the correct type
specified by RedMax. (MA3)
• Clean the cylinder fins with
compressed air or a brush. (MA4)
US-12
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
8. Maintenance
■ SAFETY LOCK (MA8)
IMPORTANT
WARNING
• If waste gets stuck and causes
blockage around the intake air cooling
vent or between the cylinder fins, it may
cause the engine to overheat, and that
in turn may cause mechanical failure
on the part of the hedge-trimmer.
• Stop operation when the safety lock
is defective.
U
S
• Safety lock is the device not to
accelerate the throttle lever without
intention. While pushing the safety lock,
you can accelerate the throttle lever.
■ BLADES
Oil blades each gas tank filling (MA5).
MA8
MA5
1. Check if the throttle lever does not
move when you do not push the safety
lock.
2. Check if the throttle lever moves when
you grasp or release it while pushing
the safety lock.
3. Check if the safety lock returns to its
original position when you release your
hand from safety lock.
• If you find any defects at the checks
above, contact your nearest servicing
dealer for repair.
WARNING
• Make sure that the blade bolts are
well tightened.
• The blade assembly is designed to
automatically compensate for any
play between the blades.
Check the cutting edges and reform with
a flat file. (MA6)
Point :
MA6
1. Keep the end corner sharp.
2. Round the root of the edge.
3. Do not use water when using a grinder.
(1) Safety lock
■ REDUCTION GEARBOX
MA9
Refill gear housing every 50 working
hours (MA9). Use greese pump. Feed
greese until it comes out of the base of
blades.
IMPORTANT
• When mounting the blade, make sure
to fasten the spacer, washer and bolt,
then fasten the nut.
Grease nipple: A type
(1) Bolt
(2) Plate
(3) Spacer
(4) Nut
■ ANTI-VIBRATION SYSTEM
WARNING
• The deformed or damaged anti-
vibration system may cause of the
breakages like getting rickety or
falling off of engine and/or blade.
■ SHARPENING (MA7)
Always keep the file or sharpener at an
angle of 45° to the blade, and:
• Always grind in the direction of the
cutting edge;
• Note: files cut only in one direction; lift
the file from the blade when returning
to start a new pass;
MA7
MA10
• [HTZ2460/HTZ2460L] Check
periodically if the rubber cushions are
not deformed or damaged.
• [CHTZ2460/CHTZ2460L] Check
periodically if the springs are not
deformed or damaged.
• Remove all burr from the edge of the
blade with a slip stone;
• Remove as little material as possible;
• Before refitting the sharpened blades,
remove filings and then apply grease.
Do not try to sharpen a damaged blade:
change it or take it to a Service dealer.
US-13
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
8. Maintenance
■ PROCEDURES TO BE PERFORMED
AFTER EVERY 100 HOURS OF USE
1. Remove the muffler, insert a
MA11
screwdriver into the vent, and wipe
away any carbon buildup. Wipe away
any carbon buildup on the muffler
exhaust vent and cylinder exhaust port
at the same time.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has
worked its way in between the clutch
lining and drum, and if it has, wipe it
away using oil-free, lead-free gasoline.
■ MUFFLER
WARNING
• Inspect periodically, the muffler for
loose fasteners, any damage or
corrosion. If any sign of exhaust
leakage is found, stop using the
machine and have it repaired
immediately.
• Note that failing to do so may result
in the engine catching on fire.
MA12 [HTZ]
■ SPARK ARRESTER
• The muffler is equipped with a spark
arrester to prevent red hot carbon from
flying out of the exhaust outlet.
Periodically inspect and clean as
necessary with a wire brush.
In the State of California it is required
by law (Section 4442 of the California
Public Resources Code) to equip a
spark arrester when a gas powered tool
is used in any forest covered, brush
covered, or grass covered unimproved
land. (MA12)(MA13)
MA13 [CHTZ]
(1) Bolt
(2) Spark arrester
US-14
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
9. Storage
1. Oil the blade to prevent rust.
2. Empty the fuel tank and put the cap
back on.
3. Remove the spark plug, pour a small
amount of oil into the cylinder.
4. Rotate the crankshaft several times
using the starting rope in order to
distribute the oil. Put the spark plug
back in.
U
S
5. Wrap the engine with a plastic sheet.
6. Store the trimmer in a dry place,
preferably not in direct contact with the
floor and away from heat sources.
10. Disposal
• When disposing your machine, fuel or
oil for the machine, be sure to allow
your local regulations.
11. Troubleshooting guide
Case 1. Starting failure
CHECK
PROBABLE CAUSES
incorrect fuel
ACTION
fuel tank
fuel filter
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
drain it and with correct fuel
clean
fuel filter is clogged
out of normal range
spark plug is fouled/wet
plug gap is incorrect
disconnected
carburetor adjustment screw
sparking (no spark)
adjust to normal range
clean/dry
correct (GAP: .026 in (0.65 mm))
retighten
spark plug
Case 2. Engine starts but does not keep running/Hard re-starting.
CHECK
PROBABLE CAUSES
incorrect fuel or staled fuel
out of normal range
carbon is built-up
ACTION
drain it and with correct fuel
adjust to normal range
wipe away
fuel tank
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
carburetor adjustment screw
muffler,cylinder (exhaust port)
air cleaner
clogged with dust
replace
cylinder fin, fan cover
clogged with dust
clean
When your unit seems to need further service, please consult with our service shop in your area.
US-15
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY
STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS
The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment
Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later
small off-road engine. In U.S. and Canada, new equipment that use small off-road engines must be designed,
built, and equipped to meet the applicable Federal or Californian stringent anti-smog standards. RedMax must
warrant the emissions control system on your small off-road engine for the period listed below provided there
has been no abuse, neglect or improper maintenance of your equipment. Your emissions control system may
include parts such as carburetor, ignition system, catalytic converter, fuel tank, filters and other associated
components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies.
Where a warrantable condition exists, RedMax will repair your small off-road engine at no cost to you including
diagnosis, parts and labor.
MANUFACTURER'S WARRANTY COVERAGE
This emissions control system is warranted for two years or if the product qualifies for a longer warranty period
resulting from the type of use, that period shall prevail. If any emissions-related part on your equipment is
defective, the part will be repaired or replaced by RedMax.
OWNER'S WARRANTY RESPONSIBILITIES
As the small off-road engine owner, you are responsible for performance of the required maintenance listed in
your Owner's Manual. RedMax recommends that you retain all receipts covering maintenance on your small off-
road engine, but RedMax cannot deny warranty solely for the lack of receipts or your failure to ensure the
performance of all scheduled maintenance. As the small off-road engine owner, you should however be aware
that the RedMax may deny you warranty coverage if your small off-road engine or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to a RedMax distribution center or service center
as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to
exceed 30 days. If you have any questions regarding your warranty coverage, you should contact RedMax at 1-
800-291-8251 or via e-mail at [email protected].
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.
LENGTH OF COVERAGE
RedMax warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is
designed, built, and equipped so as to conform with all applicable regulations adopted by EPA and CARB, and
is free from defects in materials and workmanship that causes the failure of a warranted part for a period of two
years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty
must be performed at no charge to the owner at a warranty station. Warranty services or repairs will be provided
at all RedMax distribution centers that are franchised to service the subject engines. Throughout the emissions
warranty period of two years, RedMax must maintain a supply of warranted parts sufficient to meet the expected
demand for such parts.
WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance
schedule, is warranted for the period of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired or replaced by RedMax at no cost.
Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first
scheduled replacement point for the part. Any warranted part that is not scheduled for replacement as required
in the maintenance schedule, is warranted for two years or if the product qualifies for a longer warranty period
resulting from the type of use, that period shall prevail. If any such part fails during the period of warranty
coverage, it will be repaired and replaced by RedMax at no cost. Any such part repaired or replaced under the
US-16
Download from Www.Somanuals.com. All Manuals Search And Download.
HTZ2460/HTZ2460L/CHTZ2460/CHTZ2460L
warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular
inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written
instructions to the effect of "repair or replace as necessary" will not reduce the period of warranty coverage. Any
such part repaired or replaced under warranty will be warranted for the remaining warranty period.
U
S
DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a
warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station.
CONSEQUENTIAL DAMAGES RedMax is liable for damages to other engine components proximately caused
by a failure under warranty of any warranted part.
EMISSION WARRANTY PARTS LIST
1. Air-induction system*
2. Fuel system*
3. Ignition system*
4. Fuel tank, cap and lines as applicable*
*some components only covered up to point specified by maintenance schedule
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper maintenance are not covered.
ADD-ON OR MODIFIED PARTS
Add-on or modified parts that are not exempted by CARB or EPA may not be used. The use of any non-
exempted add-on or modified parts will be grounds for disallowing a warranty claim. RedMax will not be liable to
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest
authorized servicing dealer or contact RedMax at 1-800-291-8251 or via e-mail at [email protected].
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all RedMax authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Any replacement part may be used in the performance of any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required maintenance, as defined in the operator's manual.
US-17
Download from Www.Somanuals.com. All Manuals Search And Download.
|