Owner’s Manual
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: E100/125/150 must be traveling
Item Numbers
E100
E125
3mph before motor will engage. Kick start to
13100E-BL
13125E-BK Black
13111110 Red
13111612
3mph then twist the throttle to start motor.
E150
E200
13200E-SL
13201S-SL
13112850
13300E-SL
13301S-SL
13116390
E200S
E225S
E300
E300S
E325S
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Remove contents from box. Remove the foam separators that protect the components from damage during
shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there
should not be any problems, even if the box has a few scars or dents.
WARNING:
DO NOT USE NON-
RAZOR PRODUCTS WITH
YOUR RAZOR ELECTRIC
SCOOTER. The scooter has
been built to certain Razor design
specifications. The original
equipment supplied at the time of
sale was selected on the basis of
its compatibility with the frame,
fork and all other parts. Certain
aftermarket products may or may
not be compatible.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult with experience in bicycle mechanics.
Allow up to 20 minutes for assembly, not including initial charge time.
Allow up to 12 hours for initial charge (see page 3 for charging information.
Brake Lever
Speed Control
Brake Lever
Adjuster
T-tube
Handlebar height adjust
quick-release
Charger
Extension Tube
Charger
Port
Charger
Plug
Folding System
Locking Knob
Headset
On/off switch
and charging port
Front Fork
Battery pack
and motor
controller
Tire
Wheel
Required Tools
Some tools may be supplied; however, we recommend the use of mechanic’s grade tools. Use the supplied
tools only as a last resort.
6mm hexagonal
key wrench
(included)
Inflation valve
adapter/extender
(with E200 & E300
only)
Bicycle-style tire pump
for Schrader valve
tires, with pressure
gauge
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND SET-UP
q Charging the Battery
WARNING: Always
disconnect your scooter from
the charger before cleaning with
liquid.
Your electric scooter may not have a fully charged battery. Therefore it is a good idea to charge the battery
prior to use.
• Initial charge time: 12 hours
• Recharge time: up to 8 hours,
Battery should be recharged
a minimum of 8 hours after
each use. When the vehicle
is not in regular use, recharge
the battery at least once a
month until normal use
• Run time: up to 40 minutes
• Average battery life: 250 charge/discharge cycles
Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.
is resumed.
The charger has a small window
with one LED or two LEDs to
indicate the charge status.
Refer to the illustration on
the charger unit for the actual
“charging” and “charged” status
indications for your model
charger.
Charger
Port
1 Plug the charger port into the
2 Plug the charger plug into a
port on the scooter. The charger
works with the power switch
in either the on or off position.
The charging input, on/off
switch and overload breaker are
located under the deck at the
front left-hand side.
wall outlet.
Charger
Plug
Chargers have built-in over-
charge protection to prevent
battery from being over-charged.
Be sure to properly align the
groove on the charger input
plug with the corresponding
socket on the case;
otherwise, no charging
action will occur.
q Attaching the Handlebars
WARNING: Failure
to recharge the battery at least
once a month may result in
a battery that will no longer
accept a charge.
1 Loosen the locking knob
and swing to the 6 o’clock po-
sition to unfold the handlebar.
2 Remove the plastic protector
3 Slide the quill into the
fork until it bottoms on the
headset.
covering the base of the handle-
bar assembly. Insert the “quill”
part of the handlebar assembly
into the fork. You may have to
loosen the wedge to allow it to
slip into the fork.
WARNING: Failure
to properly tighten the wedge
may allow the handlebars to
dislodge while riding and may
cause you to lose control and
fall. When correctly tightened,
the handlebars will not rotate
out of alignment with the
front wheel under normal
circumstances.
WARNING: Keep your
fingers clear of the pivoting
mechanism when folding or
unfolding the scooter, and make
sure others are standing clear.
6 Swing the locking knob to
the 12 o’clock position and
tighten by hand as firmly as
possible.
5 Pivot the handlebar assembly
4 Using a 6mm hexagonal
key wrench, tighten the
wedge by turning the bolt
clockwise. The wedge is
properly tightened when the
handlebars cannot be twisted
out of alignment with the
front wheel.
Note: The cable and wire
assembly from the handlebar
must not wrap around the
steering tube or handlebar
as shown in step 3. Sharp
bends or twisting of the brake
cable can cause the brakes to
malfunction.
upright.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY AND SET-UP
q Adjusting the Handlebar Height (E100/E200/E300 only)
WARNING: Failure
to properly engage the quick-
release clamp may cause the
T-tube to move up or down
while riding, which may cause
you to lose control and fall.
With the quick-release properly
adjusted and engaged, the
handlebars will not move up or
down.
Note: Be careful not to over-
tighten. You should be able
to open and close the quick-
release lever by hand, and the
T-tube should move up and
down freely with the quick-
release open.
1 Pull the quick-release lever
2 Slide the T-tube to the
3 The tension of the quick-
release clamping mechanism
can be adjusted by tightening
or loosening the bolt with
your fingers.
outward.
desired position and secure by
pushing the quick-release lever.
q Riding Your Scooter
Testing the Brakes – To use the brakes, squeeze the front and back brake levers to increase the
pressure on the brake. The brake lever is fitted with a cable adjuster to compensate for cable stretch
and/or to fine-tune the lever movement to brake engagement. If brake is not engaging properly, follow
instructions for adjusting the brakes on page 5.
Note: The E100 must be going 3 mph before the motor will start. Kick to 3 mph then activate the speed
control while simultaneously pressing the green“go” button to engage the motor.
REPAIR AND MAINTENANCE
Check the Razor web site for any updates on the latest repair and maintenance procedures.
Turn power switch off before conducting any maintenance procedures.
q Adjusting the Brakes
1 To adjust the brake cable
play, thread the brake lever
adjuster in or out 1/4 to 1/2 turn
until the desired brake adjust-
ment is attained. Most
adjustments are complete at
this step. If brake still needs
further adjustment, proceed to
step 2.
2 (E100)
2 (E125, E200 & E300)
If the brake lever adjuster is
threaded outward and the brake
still has too much slack, use the
rear brake adjuster for additional
adjustment.
WARNING: The
brake is capable of skidding
the tire and throwing an
unsuspecting rider. Practice
in an open area free from
obstacles until you are familiar
with the brake function. Avoid
skidding to a stop as this can
cause you to lose control or
damage the rear tire.
Inspect the brake pads (A)
for proper alignment against
the wheel or excess wear. To
realign brake pads, loosen the
fixing nut (B) and adjust the pad
to contact the rim. Retighten
and test the function, readjust
as needed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
q Inflating the Tires
Tires are inflated when shipped, but they invariably lose some pressure between the point of
manufacturing and
your purchase.
WARNING: Failure
to remove the valve adapter
after inflating will cause the
inner tube and/or adapter to
be severed by the rear drive
sprocket.
E150 / E200 / E300 Rear Tire
Note: If you lose the adapter,
a valve stem extender can be
purchased at almost any auto
parts store.
1 Use the special valve
extender/adapter supplied.
The valve adapter is located
in the bag with the owners
manual supplied at the time
of purchase.
2 Align the access hole in
the drive sprocket with the
tire valve. Thread the adapter
completely onto the valve and
attach the pump. Inflate to
the PSI indicated on the tire
sidewall.
3 Remove valve adapter
Note: The pressurized air
supplies found at gasoline
stations are designed to inflate
high-volume automobile tires.
If you decide to use such an air
supply to inflate your electric
scooter tires, first make sure
the pressure gauge is working,
then use very short bursts to
inflate to the correct PSI. If you
inadvertently over-inflate the
tire, release the excess pressure
immediately.
immediately after inflating.
E150 / E200 / E300 Front Tire and E100 Tires
1 Using a bicycle style tire
pump equipped for a Schrader-
type valve, inflate the front
tire to the PSI indicated on the
sidewall of the tire.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
q Adjusting the Chain
Tools required: 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches.
Note: This system of adjusters
is common to motorcycles and
BMX bicycles. If you are not
familiar with it or do not feel
comfortable performing the ad-
justment, consult an authorized
Razor service center or a quali-
fied BMX bike or motorcycle
mechanic.
The chain should be “just taut”
– in other words snug, but not
piano-wire tight. The tension
should be similar to the fan
chain on an automobile. BE
CAREFUL NOT TO ADJUST TOO
TIGHT. The tensioning system
can easily impart too much ten-
sion and snap the chain or bend
the motor shaft. Adjust 1/8 to
1/4 turn at a time and check the
tension each time.
1 Using two 17mm wrenches,
loosen the rear axle bolts by
turning the wrenches counter
clockwise.
2 Using two 8mm wrenches,
loosen the brake housing anchor
which is located in the long slot
on the left side of the rear fork.
3 Using a 10mm wrench,
tighten the tension adjusters on
the axle 1/8 to 1/4 turn to fine-
tune the chain tension. Both
adjusters must be tightened the
exact same amount to maintain
wheel alignment.
4 Once the tension is correct,
tighten the axle and brake an-
chor bolt. Test run the scooter.
Readjust as needed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
q Chain and Rear Tire Replacement
Tools required: Phillips screwdriver, 10mm wrench, two (2) 8mm wrenches, and two (2) 17mm wrenches.
1 With a Phillips screwdriver,
loosen the two screws and
remove the chain guard.
2 With a 10mm wrench,
loosen the brake cable anchor
and disconnect the cable.
3 With two 8mm wrenches,
loosen brake housing anchor
and disconnect. Keep the spacer
and washers together.
4 With a 10mm wrench, loosen
both axle adjusters an equal
amount, about five turns.
5 With two 17mm wrenches,
loosen the axle. Push the wheel
forward in the slots to loosen
the chain.
6 Pull the wheel out. Note the
arrangement of the hardware
sequence. The spacer order is
small, medium and large, with
the small spacer between the
brake and frame, the medium
between the brake and wheel
and the long between the wheel
and frame.
7 Install new chain or wheel by
maneuvering the chain onto the
sprocket and slipping the axle
into the slots on the frame.
8 To hook up the brake housing
anchor, align the cable guide
adjuster and install the spacer
and bolt. Do not tighten until
final step.
9 Install the brake spring and
thread the cable wire into the
cable anchor. Thread the cable
to its original position and
tighten securely.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
10 Install the axle adjusters
and axle nuts. Tighten until they
just barely hold the hardware
in place.
11 Tighten both axle adjust-
ers the same number of turns
to fine-tune the tension on the
chain and to approximately
maintain the centering of the
wheel.
12 Tighten the brake housing
anchor securely. Test ride and
check. Readjust as needed.
13 Replace the chain guard.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
q Front Tire Replacement
Tools required: 10mm wrench, two (2) 17mm wrenches and a flathead screwdriver.
1 (E100 only, other
models go to Step 2)
Loosen the brake pad bolt and
remove one brake pad.
2 Using two 17mm wrenches,
loosen the front axle bolts by
turning the wrenches counter
clockwise.
3 Remove wheel and replace
tire. To reinstall wheel, reverse
these steps. Helpful hint: You
may need to use a flathead
screwdriver to center the axil
and the bolts.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR AND MAINTENANCE
WARNING: If a
battery leak develops, avoid
contact with the leaking acid
and place the damaged battery
in a plastic bag. Refer to the
disposal instructions at left. If
acid comes into contact with
skin or eyes, flush with cool
water for at least 15 minutes
and contact a physician.
q Battery Care and Disposal
Do not store the battery in temperatures above 75° or below -10° F.
CONTAINS SEALED LEAD BATTERY. BATTERY MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in
an environmentally sound manner. Do not dispose of a lead-acid battery in a fire. The battery may explode
or leak. Do not dispose of a lead-acid battery in your regular household trash. The incineration, land filling
or mixing of sealed lead-acid batteries with household trash is prohibited by law in most areas. Return
exhausted batteries to a federal or state approved lead-acid battery recycler or a local seller of automotive
batteries. If you live in Florida or Minnesota, it is prohibited by law to throw away lead-acid batteries in the
municipal waste stream.
q Charger
The transformer/charger supplied with the scooter should be regularly examined for damage to the cord,
plug, enclosure and other parts, and, in the event of such damage, the scooter must not be charged until it
has been repaired
or replaced.
Use ONLY with the recommended charger.
q Replacement Parts
The most frequently requested replacement parts (wheels, tires, tubes, batteries and chargers) are
contact an authorized Razor repair center.
q Repair Centers
For a list of authorized Razor repair centers:
• Send e-mail to [email protected] or call 866-467-2967 for the center nearest you.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
Solution
Scooter does not run
Undercharged battery
Charge the battery. A new battery should have been charged for at
least 12 hours before using the scooter for the first time and up to 8
hours after each subsequent use.
Check all connectors. Make sure the charger connector is tightly
plugged into the charging port, and that the charger is plugged into
the wall.
Charger is not working
Make sure power flow to the wall outlet is on.
Loose wires or connectors
You may check to see if your charger is working by using a volt meter
or asking your local Razor authorized service center to test your
charger for you.
E100 only - Scooter must be
traveling 3mph before motor will
engage.
Kick start to 3mph then twist the throttle to start motor.
Scooter was running but
suddenly stopped
Tripped circuit breaker
Check all wires and connectors to make sure they are tight.
The circuit breaker (next to on/off switch) will automatically shut off
the power if the motor is overloaded.
An excessive overload, such as too heavy a rider or too steep a hill,
could cause the motor to overheat. If the scooter suddenly stops
running, wait a few seconds and then push the breaker to reset the
circuit. Correct the conditions that caused the breaker to trip and
avoid repeatedly tripping the breaker.
Short run time (less than
30 minutes per charge)
Undercharged battery
Charge the battery. A new battery should have been charged for at
least 12 hours before using the scooter for the first time and up to 8
hours after each subsequent use.
Check all wires and connectors. Make sure the battery connector is
tightly plugged into the charger connector, and that the charger is
plugged into the wall.
Battery is old and will not accept
full charge
Make sure power flow to the wall outlet is on.
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 1 to 2 years depending on scooter use and
conditions. Replace only with a Razor replacement battery.
Brakes are not adjusted properly
Driving conditions are too stressful
Refer to adjusting the brakes instructions on page 4.
Scooter runs sluggishly
Use only on solid, flat, clean and dry surfaces such as pavement or
level ground.
Tires are not properly inflated
The tires are inflated when shipped, but they invariably will lose
some pressure between the point of manufacturing and your
purchase. Refer to instructions on page 5 of this manual to properly
inflate tires.
Scooter is overloaded
Make sure you do not overload the scooter by allowing more than
one rider at a time, exceeding the E100 120 lb. or E200 and E300 220
lb. maximum weight limit, going up a hill or towing objects behind
the scooter. If the scooter is overloaded, the circuit breaker may trip
and shut off power to the motor. Correct the driving conditions that
caused the overload, wait a few seconds, and then push the breaker
to reset the circuit. Avoid repeatedly tripping the circuit breaker.
Brake dragging
E100: Use your fingers to twist the adjuster in either direction until
wheel is centered between pads.
E200/E300: Adjust brake at lever (page 4) to allow wheel to spin
without brake contact.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Problem
Possible Cause
Solution
Refer to adjusting the brakes instructions on page 4.
Sometimes the scooter
doesn’t run, but other
times it does
Brakes are not adjusted properly
Check all wires around the motors and all connectors to make sure
they are tight.
Loose wires or connectors
Contact your local Razor authorized service center for diagnosis and
repair.
Charger gets warm
during use
Motor or electrical switch
damage
No action required. This is normal for some chargers and is no cause
for concern. If your charger does not get warm during use, it does not
mean that it is not working properly.
Scooter does not stop
when applying the brake
Normal response to charger use
Refer to adjusting the brakes instructions on page 4.
Scooter makes loud
noises or grinding
sounds
Brakes are not adjusted properly
Chain is too dry
Apply a lubricant such as 3 in 1TM or Tri-FlowTM to the chain.
Use your fingers to twist the caliper adjuster in either direction until
rotor is centered between pads.
Brake rotor is dragging on brake
pads
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
E100 PARTS
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
10 Front caliper brake
11 Battery tray
01 Handlebar grip (right/left)
02 Single speed twist grip throttle
02-1 Sleeve
12 On/ Off switch
13 Charger port w/ wires
14 Reset button w/ wire
15 Control module
16 Battery (2- 12V/ 4.5Ah)
17 Kickstand
03 Handlebar stem/ T-bar
03-1 Black folding knob
03-2 6mm stem bolt
03-3 Washer
03-4 Wedge
18 Motor (24V / 100W)
19 Rear wheel complete
20 Chain
04 Brake lever assemble complete
05 Headset (upper)
06 Frame
20 Chain guard
07 Headset (lower)
08 Front fork
20 Deck plate w/ grip take set
09 Front wheel complete
13
Download from Www.Somanuals.com. All Manuals Search And Download.
E100 PARTS
14
Download from Www.Somanuals.com. All Manuals Search And Download.
E150 PARTS
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
09 Front wheel complete
10 Battery tray
01 Handlebar grip (right/left)
01-1 Valve stem extender/ inflator
01-2 Handlebar end cap/ Extender holder
02 Brake lever assemble complete
03 Handlebar stem/ T-bar
03-1 Black folding knob
03-2 6mm stem bolt
11 On/ Off switch
12 Reset button w/ wire
13 Charger port w/ wires
14 Control module
15 Battery (2- 12V/ 4.5Ah)
16 Motor (24V/ 100W)
17 Kickstand
03-3 Washer
03-4 Wedge
18 Rear wheel complete
19 Chain
04 Speed controller w/ LEDs
04-1 Sleeve
20 Chain guard
05 Headset (upper)
21 Deck, Upper plate
22 Main deck board
06 Frame
07 Headset (lower)
08 Front fork
15
Download from Www.Somanuals.com. All Manuals Search And Download.
E150 PARTS
16
Download from Www.Somanuals.com. All Manuals Search And Download.
E200 PARTS
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
11 Front wheel complete
12 Battery tray
01 Handlebar Grip (right/left)
01-1 Valve stem extender/ inflator
01-2 Handlebar end cap, Extender holder
02 Speed controller w/ LEDs
02-1 Sleeve
13 Reset button w/ wire
14 On/ Off switch
15 Charger port w/ wires
16 Control module
17 Motor (24V/ 200W)
18 Kickstand
03 T-bar
04 Brake lever assemble complete
05 Quick release
19 Battery (2- 12V/ 7Ah)
20 Rear wheel complete
21 Chain
06 Extension tube/ Folding system
06-1 Black folding knob
06-2 6mm stem bolt
22 Chain guard
06-3 Washer
23 Rear fender
06-4 Wedge
24 Deck
07 Headset (upper)
08 Frame
25 Seat post
26 Seat
09 Headset (lower)
10 Fork front
17
Download from Www.Somanuals.com. All Manuals Search And Download.
E200 PARTS
Only used on E200S
18
Download from Www.Somanuals.com. All Manuals Search And Download.
E300 PARTS
Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.
(Specifications subject to change without notice.)
09 Front wheel complete
10 Battery tray
01 Handlebar grips (right/left)
01-1 Valve stem extender/ inflator
01-2 Handlebar end cap, Extender holder
02 Single speed twist grip throttle
02-1 Sleeve
11 Reset button
12 On/ off switch
13 Charger port w/ wires
14 Control module
15 Battery (2- 12V/ 7Ah)
16 Motor (24V/ 250W)
17 Kickstand
03 Handlebar Stem/ T-bar
03-1 Black folding knob
03-2 6mm stem bolt
03-3 Washer
18 Rear wheel complete
19 Chain
03-4 Wedge
04 Brake lever assemble complete
05 Headset (upper)
20 Chain guard
21 Deck plate w/ grip tape
22 Seat post
06 Frame
07 Headset (lower)
23 Seat
08 Front fork
19
Download from Www.Somanuals.com. All Manuals Search And Download.
E300 PARTS
Only used on E300S
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SB 1918 (CALIFORNIA) DECLARATION
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR
ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC
VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD
CONTACT YOUR INSURANCE COMPANY OR AGENT.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY REMINDERS
PRE-RIDE CHECKLIST
Loose Parts
Tire Inflation
Check and secure all fasteners before every
ride. Make sure steering stem clamp bolts are
locked properly in place. There should not be any
unusual rattles or sounds from loose parts or
broken components. If you are not sure, ask an
experienced mechanic to check.
Periodically inspect the tires for excess wear,
q and regularly check the tire pressure and re-
q
inflate as necessary. If you get a flat tire, the
inner tube can be patched or a new tube can be
purchased from Razor or an authorized repair
center.
Safety Gear
Brake
Always wear proper protective equipment such
q
Check the brakes for proper function. When
you squeeze the lever, the brake should provide
positive braking action. When you apply the
brake with the speed control on, the brake cut-
off switch will stop the motor.
q
q
as an approved safety helmet, elbow pads and
kneepads. Always wear athletic shoes (lace-up
shoes with rubber soles), never drive barefooted
or in sandals, and keep shoelaces tied and out of
the way of the wheels, motor and drive system.
Frame, Fork and Handlebars
Check for cracks or broken connections.
Although broken frames are rare, it is possible
for an aggressive driver to bash into a curb or
wall and wreck and bend or break a frame. Get
in the habit of inspecting yours regularly.
DO NOT RETURN TO STORE
Do not use this vehicle for the first time until you have inflated the
tires to the correct PSI and charged the battery for at least 12 hours.
Failure to follow these instructions may damage
your vehicle and void your warranty.
WARRANTY
Razor Limited Warranty
For your records, save your original sales receipt with this manual and
write the serial number below.
The manufacturer warranties this product to be free of manufacturing
defects for a period of 90 days from date of purchase. This Limited
Warranty does not cover normal wear and tear, tires, tubes or
cables, or any damage, failure or loss caused by improper assembly,
maintenance, or storage or use of the Razor electric chopper.
__________________________________________
Item Numbers
E100
13100E-BL
13125E-BK Black
13111110 Red
13111612
13200E-SL
13201S-SL
13112850
13300E-SL
13301S-SL
13116390
E125
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation or transportation
• modified in any way;
E150
E200
E200S
E225S
E300
• rented.
The manufacturer is not liable for incidental or consequential loss or
damage due directly or indirectly to the use of this product.
E300S
E325S
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.
Community Design No. 130919-0001
U.S. Design Patent D497,397 S
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
© Copyright 2007 Razor USA. All rights reserved.
12102007
Download from Www.Somanuals.com. All Manuals Search And Download.
|