Ramsey Electronics Radio FR6 User Guide

6 METER FM  
RECEIVER KIT  
Ramsey Electronics Model No.  
FR6  
Check out the 6 meter action with this simple and fun to build  
FM receiver. Receive crystal-clear signals from thousands of  
miles away! Six meters is a fascinating band! Tune the entire 6  
Meter band or the VHF low Police and Fire band.  
Tunes any 5 MHz portion of the 40 to 60 MHz band.  
Excellent performance, less than 1 uV sensitivity.  
Tuned input, low noise preamp stage.  
True Dual-conversion superhet design with 2 pole  
Ceramic High IF and 6 pole Ceramic low IF filters!  
Front Panel Volume, Squelch, and Tuning controls.  
Excellent receiver for beginners and seasoned pros!  
Informative manual answers questions on theory, hook-  
ups, and uses - enhances resale value, too!  
Add our case set for a finished ‘Pro’ look. Cases match  
all Ramsey products.  
Clear, concise assembly instructions carefully guide  
you to a finished kit that works the FIRST time!  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Ramsey Publication No. MFR6  
Price $5.00  
KIT ASSEMBLY  
AND INSTRUCTION MANUAL FOR  
FR6 6 METER  
FM RECEIVER KIT  
TABLE OF CONTENTS  
Introduction to the FR6.................. 4  
Circuit Description ......................... 5  
Parts List........................................ 6  
Simplified Block Diagram .............. 8  
Parts Layout Diagram.................... 9  
Schematic Diagram....................... 10  
FR6 Assembly Instructions ........... 11  
Testing and Alignment................... 18  
Enclosure Ideas............................. 20  
Troubleshooting Guide.................. 21  
Notes for Advanced Users ............ 22  
Ramsey Kit Warranty .................... 23  
FR6 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
FM and repeaters on 6 meters? You bet!  
There's not a lot to say about using the FR6 receiver once its been correctly  
built and aligned. If 6 meters is "dead”, it resembles the usual 2 meter action.  
If 6 meters is "hot", you’ll find an amazing variety of crystal-clear FM signals  
from many thousands of miles away! If there are local 6 meter repeaters in  
your area, the FR6 will be just as active as the local repeater gang.  
Since the FR6 “hears” only FM, the various SSB and CW signals on the band  
will not be properly demodulated as to be intelligible.  
This receiver is a good project for amateurs wishing to become more familiar  
with 6 meter FM before choosing a transceiver, or for those active on 6 who  
want an inexpensive receiver to take on trips, keep in a briefcase or to watch  
for band openings.  
Most Ramsey Electronic Kits can be classified as "Skill Level 1" if we use the  
old Heathkit guidelines for ease of assembly. That means that our kits are  
intended to be successful for first-time kit builders. This FR6 FM Receiver is  
best regarded as a "Skill Level 2" project, (or least Level 1.46!) and should  
not be taken lightly, even by experienced, licensed radio amateurs.  
Still, this step-by-step manual is written with the beginner in mind, because  
we are well aware of the fascination that Six Meters and its maze of  
repeaters holds for newcomers, which means this could be your very first kit  
project. The same holds true for those who just want to peek in on LOW VHF  
public service communications without the cost of a scanner. To be honest,  
we'd like to see first-time builders start out with an easier kit such as the  
Ramsey HR40 Forty Meter receiver before assembling the FR6, but we are  
confident that you can construct the FR6 successfully if you follow this  
manual carefully and patiently.  
Before beginning the project or even studying the circuit description, it is  
worthwhile to develop some prior respect for how much receiver is packed  
onto the circuit board. The nine semiconductor devices (diodes, transistors  
and IC chips) give the equivalent of about 30 or more transistors diodes. And,  
in addition to four inductors, a crystal and two ceramic filters, there are nearly  
60 capacitors and resistors. Surely, all that should result in a decent receiver!  
You could easily spend twice the money plus hours of time trying to gather  
the equivalent parts from catalogs and still need to make your own circuit  
board.  
FR6 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BUILDING YOUR FR6 KIT  
There are just over 200 solder connections on the FR6 printed circuit board.  
That means your work could be 99% excellent and you could STILL have 2  
or 3 cold solder points or solder bridges. Since this circuit is more  
sophisticated than a direct-conversion HF receiver or a simple transmitter, a  
beginner or casual amateur could have a harder time tracing a problem due  
to a poor solder connection. Therefore, PLEASE take us seriously when we  
say that good soldering is essential to the proper operation of your receiver!  
ˆ Use a 25-watt soldering pencil with a clean, sharp tip.  
ˆ Use only rosin-core solder intended for electronics use.  
ˆ Use bright lighting. A magnifying lamp or bench-style magnifier may be  
helpful.  
ˆ Do your work in stages, taking breaks to check your work.  
ˆ Carefully brush away wire cuttings so they don't lodge between solder  
connections.  
FR6 CIRCUIT DESCRIPTION  
VHF signals from the antenna are amplified through the tuned input circuit  
(L1,C3 and L2,C4) by Q1, a microwave bipolar transistor. Q1's output is fed  
to the input of the SA602 IC, an efficient single-package (8-pin DIP) mixer-  
product detector-oscillator. The tuneable oscillator section of the SA602 is  
aligned to operate at 10.7 MHz higher than the signal fed and amplified by  
Q1. For example, to receive 50-54 MHz signals, the oscillator must tune 60.7  
to 64.7 MHz in order for the SA602's mixing capability to produce a steady  
10.7 MHz output signal to the rest of the circuit. The oscillator frequency is  
determined by L3 and its associated capacitors, and varied by the varactor  
tuning network using D1 and varied by R1.  
The output from pin 4 of the SA602 passes through a ceramic 10.7 MHz filter,  
amplified by transistor Q2 and applied to input pin 18 of U2.  
Q3 provides AFC (Automatic Frequency Control) by keeping the local  
oscillator of U1 from drifting away from an incoming signal. This is  
accomplished by tuning the varactor circuit in the direction opposite the drift.  
The MC3359 IC has an internal oscillator controlled by the 10.24 MHz crystal.  
The 10.24 MHz signal is mixed with the 10.7 MHz input from U1 to convert  
down to the low IF of 450 KHz. The 450 KHz IF is filtered by FL2 and then  
amplified by a limiting amplifier in U2. Audio demodulation takes place in the  
quadrature detector, with L4 adjusting the detector.  
The audio modulation is detected in U2, and the background noise is used to  
control the squelch. U3 amplifies the audio output from pin 10 of U2 to a  
FR6 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
practical level for speaker or headphone operation. Pin 16 of U2 will ground  
the input of U3 when the squelch is closed.  
L4, a 450 KHz IF coil, permits adjustment of the 90-degree voltage-current  
phasing ("quadrature") of FL2's output to the FM detector demodulator (pin 8  
of the MC3359).  
PARTS LIST  
Inductors  
ˆ 2 .15 uH inductors [looks like a resistor with brown-green-silver  
bands] (L1,L2)  
ˆ 1 slug-tuned turn coil [blue color] (L3)  
ˆ 1 shielded transformer coil [marked LB 53303] (L4)  
Semiconductors and IC's  
ˆ 1 2SC2498 or 2SC2570A transistor (Q1)  
ˆ 3 2N3904 transistor (Q2,Q3,Q4)  
ˆ 1 SA602 8-pin IC (U1)  
ˆ 1 MC3359 18-pin FM receiver IC (U2)  
ˆ 1 LM386 8-pin audio amplifier IC (U3)  
ˆ 1 Varactor diode, BB505 [orange body marked BB505] (D1)  
ˆ 1 1N4148 signal diode (D2)  
Special Components  
ˆ 1 10.24 MHz Crystal (Y1)  
ˆ 1 10.7 MHz ceramic filter [brown, molded, 3 leads] (FL1)  
ˆ 1 450 KHz ceramic filter [black, square] (FL2)  
Fixed Resistors  
ˆ 1 2 ohm [red-black-gold] (R22)  
ˆ 3 270 ohm [red-violet-brown] (R6,9,20)  
ˆ 1 470 ohm [yellow-violet-brown] (R5)  
ˆ 2 1K ohm [brown-black-red] (R11,12)  
ˆ 3 10K ohm [brown-black-orange] (R7,17,19)  
ˆ 1 18K ohm [brown-gray-orange] (R18)  
ˆ 1 33K ohm [orange-orange-orange] (R14)  
ˆ 4 47K ohm [yellow-violet-orange] (R4,8,13,21)  
ˆ 1 100K ohm [brown-black-yellow] (R16)  
ˆ 1 470K ohm [yellow-violet-yellow] (R15)  
ˆ 1 1 megohm [brown-black-green] (R10)  
Capacitors  
ˆ 1 4.7 or 5 pF (C2)  
ˆ 2 10 pF (C1,5)  
ˆ 1 22 pF (C19)  
FR6 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ˆ 4 62 pF (C3,4,9,10)  
ˆ 4 100 pF [marked 100, 101, or 101K] (C6,11,12,22)  
ˆ 1 220 pF [marked 220 or 221] (C18)  
ˆ 6 .001 uF [marked .001 or 102 or 1 nF] (C7,8,20,23,24,25)  
ˆ 8 .01 uF [marked .01 or 103 or 10 nF] (C13,16,17,21,26,28,29,31)  
ˆ 1 .1 uF [marked .1 or 104] (C34)  
ˆ 1 1.0 uF electrolytic (C27)  
ˆ 3 4.7 or 10 uF electrolytic (C15,30,36)  
ˆ 4 100 to 220 uF electrolytic (C14,32,33,35)  
Controls and Hardware  
ˆ 1 Printed circuit board  
ˆ 3 10K ohm potentiometer (R1,R2,R3)  
ˆ 1 DPDT push switch (S1)  
ˆ 1 PC mount RCA jack (J1)  
ˆ 1 PC mount subminiature speaker jack (J2)  
ˆ 1 9-volt battery bracket  
ˆ 1 9-volt battery snap-on clip  
REQUIRED, NOT SUPPLIED  
ˆ 1 9-volt alkaline battery  
ˆ 1 VHF antenna with cable terminated in RCA-style plug or adapter  
ˆ 1 Speaker or headphones  
NOTE CONCERNING THE AUDIO OUTPUT JACK  
Your receiver kit is supplied with a standard subminiature 2.5 mm (3/32")  
audio output jack, which mates with commonly available earphone plugs and  
adapters available at Radio Shack, such as 274-290 (plug) or 274-327  
(adapter for 1/8" mono plug). If you prefer to use another size and style jack,  
we suggest that you still install the original jack and then wire your own jack in  
parallel with it rather to rough up the PC board to accommodate your jack.  
FR6 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FR6 BLOCK DIAGRAM  
U2, 3359  
FR6 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FR6 PARTS LAYOUT DIAGRAM  
FR6 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FR6 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RAMSEY “Learn-As-You-Build” KIT ASSEMBLY:  
We have a twofold "strategy" for the order of the following kit assembly steps.  
First, we install parts in physical relationship to each other, so there's minimal  
chance of inserting wires into wrong holes. Second, whenever possible, we  
install in an order that fits our "Learn-As-You Build" Kit building philosophy.  
FOR EACH PART, OUR WORD "INSTALL" ALWAYS MEANS THESE  
STEPS:  
1. Pick the CORRECT part value to start with.  
2. Insert it into the CORRECT PC board location.  
3. ORIENT it correctly, which means: PLEASE follow the PC board drawing  
and the written directions for ALL parts where there's a right way AND a  
wrong way to solder it in. (Diode bands, electrolytic capacitor polarity,  
transistor shapes, dotted or notched ends of IC's, and so forth.)  
4. Solder ALL connections unless directed otherwise. Use enough heat and  
solder flow for clean, shiny, completed connections. Don't be afraid of  
ANY pen-style soldering iron having enough heat to damage a  
component.  
5. Trim or "nip" excess wire lengths after soldering.  
NOTE: Save some of the longer wire scraps nipped from resistors and  
capacitors. These will be used to form wire jumpers (JMP1, etc.) to be  
soldered in just like parts during these construction steps.  
Now, let's start building!  
ˆ 1. Press S1 firmly into its six holes and solder all six pins. The switch fits  
the board only one way. Ignore the other set of six solder connectors on  
the switch.  
ˆ 2. Install J1, the RCA-style antenna jack. Solder all 4 points.  
ˆ 3. Install J2, the subminiature phone jack. Solder all three points. Be  
gentle and patient in inserting, so as not to damage the solder tabs.  
ˆ 4. Install controls R1, R2 and R3. Insert the three PC mounted controls  
into their positions. Check that the controls are pressed in firmly and  
straight against the top of the board. Solder the three center pins and  
then the two larger mechanical mounting tabs. Use enough solder for a  
solid connection.  
Also, if you plan to use an enclosure other than the custom Ramsey enclosure  
and knob kit, you may wish to locate the controls differently than provided by  
FR6 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the PC board. In this case, the control lugs are wired to the PC board using  
your own insulated hookup wire, kept as short as possible for neat installation.  
All "directions" on the PC board (ie: right, left, above, below and so forth)  
assume orientation of your board as shown in the parts layout diagram.  
Therefore the rear of the board (connectors) is the lower end, and the front  
(controls) is the upper end.  
1. ANTENNA INPUT AND TUNED RF PREAMPLIFIER  
5. Install C1, 10 pF disc capacitor.  
6. Install C2, 4.7 or 5 pF.  
7. Install C3, 62 pF.  
8. Install L1, .15 uH inductor [looks like a resistor with a green colored  
body with brown, green, and silver bands].  
9. Install C4, 62 pF.  
10. Install L2, just like L1 above.  
11. Install C5, 10 pF.  
12. Clearly identify Q1, the 2SC2498 or 2SC2570A transistor. Do not  
confuse it with the other transistors supplied.  
13. Position Q1 as shown on the PC board layout, with the flat side facing  
to the right, toward the middle of the board. Press the transistor snugly  
into the PC board so that only a minimum amount of wire lead is exposed  
above the board. In soldering, don't be afraid to use enough heat to make  
good clean connections.  
14. Install R4, 47K. [yellow-violet-orange] just to the left of Q1.  
15. Install C6, 100 pF [marked 100, 101, or 101K].  
16. Install R5, 470 ohms [yellow-violet-brown].  
2. SA602 OSCILLATOR-MIXER and VARACTOR TUNING  
17. Install R6, 270 ohms [red-violet-brown].  
18. Install C7, a .001 uF bypass capacitor [marked .001, 102, or 1 nF].  
In installing the SA602 IC, you may wish to use an 8-pin DIP socket rather  
than soldering the IC directly to the board. Reasons for doing this might  
include the peace of mind of beginners afraid of damaging the IC, or  
experienced builders testing the merits of the SA602's cousin, the SE602.  
However, please be aware that we have seen more service problems with  
FR6 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
improper socket insertion than from soldering heat damage to IC's. Even if this  
is your first IC, don't be afraid to use enough heat to make 8 clean  
connections, but DO be sure to correctly orient the end marked by a band,  
dot, or notch. Before soldering, make sure that the IC or socket is perfectly flat  
against the top of the PC board.  
19. Install U1, the SA602 in accord with the preceding directions.  
20. Install the FL1 ceramic filter. This component looks like a capacitor  
with 3 leads and may be installed either way.  
21. Install jumper wire JMP4. Use a scrap component lead wire bent into  
a small loop that connects the two PC board holes. Jumpers act as  
"bridges" over PC board traces underneath.  
22. Install C8, .001 uF [marked .001, 102, or 1 nF].  
23. Install C10, 62 pF.  
24. Install R7, 10K [brown-black-orange].  
25. Install C9, 62 pF.  
26. Install C11, 100 pF [marked 100, 101, or 101K].  
27. Installation of L3. It is important that the body of this coil be snug  
against the PC board for mechanical stability, which directly affects the  
frequency stability of the receiver. Make good, solid solder connections!  
28. Install C12, 100 pF [marked 100, 101, or 101K].  
29. Install varactor diode D1, marked BB505. It is important to orient this  
part as shown in the parts layout diagram.  
31. Install R8, 47K ohms [yellow-violet-orange].  
32. Install R9, 270 ohms [red-violet-brown].  
33. Install C13, .01 uF (marked .01 or 103 or 10 nF).  
34. Installation of C14. This is the first of the electrolytic or "polarized"  
capacitors that you will install. This means these capacitors have a  
positive (+) and negative (-) side and therefore a right way and wrong way  
of installation. Ordinarily, only the negative side is marked on the capacitor  
body, a dark band with the (-) sign clearly shown. The value of C14 is not  
critical and may be any value from 100 to 220 uF.  
35. Install C14, 100 to 220 uF, observing correct polarity.  
36. Install C15, 4.7 or 10 uF, observing correct polarity.  
FR6 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37. Install jumper JMP1.  
38. Install jumper JMP3.  
PROGRESS SUMMARY  
So far, you have wired the tuned input from the antenna, the RF preamplifier,  
and the SA602 mixer-oscillator, including the varactor tuning circuit. The work  
you have done so far has actually formed a simple receiver capable of tuning  
in VHF signals of all kinds and converting them to a low-level 10.7 MHz output  
to be amplified by Q2. This is a good time to review the steps completed so far  
before proceeding. Due to the many functions of the MC3359 FM receiver IC,  
further assembly steps will be in the order of easiest parts installation.  
3. TRANSISTOR COUPLING & AFC CIRCUITS, VOLUME & SQUELCH  
CONTROLS  
39. Install Q2, a 2N3904 transistor. Observe correct positioning of the flat  
side.  
40. Install R13, 47K ohms [yellow-violet-orange].  
41. Install C20, .001 uF [marked .001, 102, or 1 nF].  
42. Install R12, 1K ohms [brown-black-red].  
43. Install Q3, 2N3904 transistor.  
44. Install R10, 1 megohm [brown-black-green].  
45. Install R11, 1K ohms [brown-black-red].  
46. Install R22, 2 ohms [red-black-gold].  
47. Install C29, .01 uF [marked .01, 103, or 10 nF].  
48. Install C30, 4.7 or 10 uF electrolytic, observe correct polarity.  
49. Install R18, 18K ohms [brown-gray-orange].  
FR6 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50. Install C28, .01 uF [marked .01, 103, or 10 nF].  
51. Install R19, 10K ohms [brown-black-orange]  
52. Install jumper wire, JMP2.  
53. Install C34, .1 uF [marked .1 or 104].  
54. Install R21, 47K ohms [yellow-violet-orange].  
55. Install C35, 100 to 220 uF electrolytic, observe polarity.  
56. Install R20, 270 ohms [red-violet-brown].  
57. Install Q4, 2N3904 transistor.  
4. MC3359 FM IC and ASSOCIATED COMPONENTS  
58. Install R17, 10K ohms [brown-black-orange].  
59. Install R14, 33K ohms [orange-orange-orange].  
60. Install C24, .001 uF [marked .001, 102, or 1 nF].  
61. Install C25, .001 uF [marked .001, 102, or 1 nF].  
62. Install C26, .01 uF [marked .01, 103, 10 nF].  
63. Install L4, the 455 KHz quadrature coil [marked LB53303], soldering  
the two pins and the two mounting tabs.  
64. Installation of MC3359 IC. As in the case of the NE602 IC, you could  
choose to install an 18-pin IC socket rather than soldering the IC directly.  
Re-read the discussion of IC sockets offered for the installation of U1.  
Larger IC's such as the MC3359 require considerably more care in socket  
insertion. Notice that the end of the IC marked by a band, dot, or notch  
must be oriented correctly as shown on the parts layout diagram. Solder  
each of the 18 connections carefully. Make sure you have good lighting as  
well as good technique to make sure that no solder "bridges" flow between  
the connections.  
65. Install C22, 100 pF (marked 100, 101, or 101K).  
66. Install C16, .01 uF [marked .01 or 103 or 10 nF].  
67. Install C17, .01 uF [marked .01 or 103 or 10 nF].  
68. Install C21, .01 uF [marked .01 or 103 or 10 nF].  
69. Install C18, 220 pF [marked 220 or 221].  
FR6 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
70. Install C19, 22 pF.  
71. Install Y1, the 10.24 MHz. crystal. No special procedure is required.  
Simply press the crystal firmly into its holes as far as it will go, and make  
good solder connections.  
72. Install FL2, the 450 KHz filter. Its three leads are delicate and fit in  
only one way.  
73. Install C23, .001 uF [marked .001, 102, or 1 nF].  
74. Install C27, 1 uF electrolytic, observe correct polarity.  
75. Install D2, the 1N4148 signal diode, observe correct orientation of the  
banded cathode end. Be sure you correctly identified D2 and did not  
confuse it with the varactor diode already installed.  
76. Install R16, 100K ohms [brown-black-yellow].  
77. Install R15, 470K ohms [yellow-violet-yellow].  
5. FINAL CONNECTIONS: THE LM386 AUDIO IC STAGE  
You now have a working FM receiver ready for adjustment. The output of the  
MC3359 FM IC simply needs to be boosted to listening level. A few more  
connections, and your receiver will be ready for adjustment and testing! Now  
would be a good time to review some of your previous work and also to make  
sure you have on hand what you'll need for testing: antenna, fresh battery,  
earphone or speaker with correct plug or adapter.  
78. Review the instructions for installing U1 and U2. Insert the LM386 IC  
(U3) with the band or dot oriented correctly. Solder the 8 connections.  
79. Install C32, a 100 to 220 uF electrolytic, observe correct polarity.  
80. Install C31, .01 uF (marked .01, 103, or 10 nF).  
81. Install C36, 4.7 or 10 uF electrolytic, observe polarity.  
82. Install C33, 100 to 220 uF electrolytic, observe polarity.  
FR6 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
83. Install the battery snap terminal in the two holes below S1, making  
sure that the positive (red) lead is inserted into the (+) hole on the PC  
board.  
84. The battery bracket may be attached in a variety of ways. A wire  
jumper can be passed through the two holes on the PC board, then both  
ends soldered on the underside of the board. You may prefer to use very  
small screws or even a double-sided mounting adhesive strip or glue. In  
using such methods, make sure that the battery will not block the PC  
board's mounting hole in its vicinity.  
Wiring of the PC board is now complete. If you have the the patience, we  
suggest a short break. Then take a magnifying lens and a bright light and  
examine all your solder joints, touching up any connection which appears less  
than perfect. Make sure all excess leads have been trimmed, and that one is  
not bent back flat against the board, possibly causing a short. Brush the solder  
side of the board with a stiff brush to make sure that no loose wire trimmings  
or solder drippings (tsk tsk) are lodged between connections.  
FR6 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TESTING, ALIGNMENT AND ADJUSTMENT  
To prepare the FR6 FM VHF Receiver for reliable monitoring operation, you  
will need these basic tools:  
ˆ 1. A useful 6 meter signal source.  
ˆ 2. Hexagonal, non-metallic coil slug alignment tool for L3.  
ˆ 3. Small screwdriver to adjust L4.  
1. Signal source: This signal can be from your test bench equipment or from  
a "live" source such as a local repeater. The "live" signals are best for fine-  
tuning, but they also have that VHF communications character of being fast  
and to the point. Good test bench signal sources include your own 6-meter  
tranceiver, if you are licensed to use it, a signal generator or grid-dip oscillator.  
If TV channel 2 (54-60 MHz) is active in your area, you may use its  
characteristic video sync “buzz” as an indicator of receiver operation. Do not  
expect to hear the audio portion clearly, since TV sound signals are fairly  
wideband FM (75 KHz) which is too much for our narrow-band FM ceramic IF  
filter.  
2. L3 Alignment Tool: If you do not already have a set of plastic or nylon coil  
alignment tools and do expect to try further Ham radio or electronic hobby  
projects, such tools are worth having and can be found inexpensively at any  
electronics store including Radio Shack. While a metal Hex key wrench can fit  
the coil slug, the metal itself would damage the coil inductance drastically and  
therefore should not be used. With patience and sandpaper, a useable tool  
might be formed from a wood or plastic rod.  
ALIGNMENT PROCEDURE  
ˆ 1. Make sure the power switch is off.  
ˆ 2. Connect the antenna, earphone or speaker and battery.  
ˆ 3. Turn the slug of L3 until it is even with the top of coil the form.  
ˆ 4. Now, turn the slug of L3 clockwise 1 1/2 turns back into the form.  
ˆ 5. Turn the slug of L4 until it is flush with the top of the coil and then turn it  
2 turns back into the coil.  
ˆ 6. Turn all three controls to the left, fully counterclockwise.  
FR6 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ˆ 7. Turn the power ON.  
ˆ 8. Turn R2 (Volume control) until you hear some noise.  
ˆ 9. Adjust L4 for maximum noise in the speaker.  
Further alignment now consists of adjusting the oscillator coil L3 to permit the  
tuning control (R3) to cover the 5 MHz. segment between 50 and 54 MHz of  
primary interest to you. Assuming you wish to adjust for the Six Meter  
Amateur Band, adjust L3 until you hear your intended test signal.  
If you are a beginner with no license or other equipment, any Ham operator  
with a 6-meter transceiver should be willing to give you the test signal and  
extra help that you need. The FR6 is very sensitive, so operate the transceiver  
on low power on a simplex frequency from a distance of at least across the  
room. An 8" piece of wire will be a sufficient receiving antenna for such tests.  
If you don't know any Hams, visit a friendly two-way radio service center to  
get close to the test signal you need!  
RECEIVER SENSITIVITY  
Your FM receiver features sensitivity under 1 uv. Radio Hams constantly  
marvel at how an FR6 displayed at hamfests tunes in dozens of hand-held  
QSO's on the premises without an antenna connected! You can expect to  
monitor local repeater and simplex transmissions easily, using a simple  
groundplane style antenna. The receiver also responds very well to the  
addition of a low-noise pre-amplifier such as the Ramsey SA7/PR2. A new  
and versatile receiver accessory is the Ramsey AA7 HF-VHF Active Antenna,  
which doubles as a preamplifier with other antennas in addition to the  
excellent performance of its own whip.  
Six meters is generally a daylight hours band. If you finish building your FR6  
at midnight, please wait until sunrise before you expect to hear much of  
anything. Quite frankly, if there are no local 6 meter operators, you may have  
to wait days until the band opens up. However, whenever 6 meters is “hot”,  
especially during the summer months, you’ll be amazed at how many stations  
will “boom” in from great distances, many running very low power!  
ADDING AN LED POWER "ON" INDICATOR  
For many people, a pilot lamp to indicate "power on" is more than a nice  
touch. They expect it and depend on it, reminding us that "real radios glow in  
the dark!" Adding a simple LED power-on indicator to your Ramsey kit  
receiver is easy. All you need is the LED itself and a small 1K to 2.2K resistor.  
FR6 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Study the PC traces between the positive battery supply wire and the on-off  
switch. The unused connectors on top of your switch are an ideal point to get  
the + DC voltage needed for the anode (longer lead) of the LED. Plan where  
and how you wish to install the LED in your enclosure.  
Locating the LED immediately above the on-off switch is logical and ideal. The  
simplest way to make a good installation is to drill a neat hole just slightly  
smaller than the diameter of the LED. Then, enlarge the hole a little bit at a  
time, just enough to let the LED be pressed in and held firmly. The resistor  
may be connected to either the anode or cathode of the LED, but the anode  
MUST go to + DC, with the cathode connected to the nearest common ground  
point. If you are wondering why we did not include these pennies worth of  
parts with your kit, you can believe any of the following reasons:  
(1) We wanted to stretch your battery budget: with the LED drawing about 6  
ma, how long will your battery last if you leave your receiver on for a few days,  
just like we leave our computers and Ham or computer accessories on all the  
time?  
(2) We thought you'd have more fun planning and installing your own lamp  
that glows in the dark!  
(3) We could not decide which color you would like best!  
THE RAMSEY ELECTRONICS CASE, KNOB & HARDWARE OPTION  
Your finished receiver can be installed in a variety of enclosures of your own  
design and choosing. You might be planning to combine several Ramsey  
circuit boards in a single enclosure. Use of the inexpensive and attractive  
Ramsey case and knob kit will give your unit that finished look and increase its  
resale value. These sturdy black instrument cases are supplied with neatly-  
lettered front and rear panels, knobs, rubber feet and mounting screws.  
OTHER ENCLOSURE RECOMMENDATIONS  
While we believe that the Ramsey enclosure and knob option is a fine value  
for finishing off your Ramsey receiver or transmitter, we are happy to give you  
a couple of additional suggestions. If your first goal is economy and rugged  
portability, you will find that the circuit board can be mounted nicely in a  
standard VHS videotape storage box, which also gives room for a speaker, or  
earphone storage, and even a roll of antenna wire. The controls are easily  
mounted at one end of such a box. It may be necessary to cut away the  
molded posts which secure the tape cassette itself. These storage boxes  
come in several styles, so pick one that looks truly practical as a project  
enclosure.  
To accomplish RF shielding, the most economical metal enclosure nicely  
FR6 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
suited for Ramsey amateur kit boards is Radio Shack No. 270-253A. This  
metal utility cabinet can accommodate both a receiver and transmitter board,  
plus speaker, with room for various refinements you might like to add.  
FR6 TROUBLESHOOTING GUIDE  
The Ramsey FR-series FM receivers are among our most widely-used and  
popular kits. The circuit itself, assembly and use are "cut-and-dried." If your  
receiver does not work, there is probably either an error in assembly or a  
defective part. Following is some help in case you experience difficulty.  
Problem: Receiver completely "dead"- no sound at all.  
Check the following:  
ˆ First, the cable or plug adapter leading to speaker or phones!  
ˆ Battery condition and battery wire polarity and soldering at S1.  
ˆ Connections associated with U3, the LM386 audio output IC.  
Problem: Receiver "hisses", but NO signals are heard, not even a signal  
generator 2 inches away.  
First, you need to verify that the local oscillator (SA602, L3, etc.) is operating.  
Use another VHF receiver or a frequency counter to verify oscillator operation.  
Next, make sure that the 10.24 MHz. crystal oscillator is running by tuning a  
general purpose HF ("shortwave") receiver to that frequency. If either  
oscillator is not running, re-check correctness of parts and solder joints  
associated with both oscillator circuits. Further signal-path tracing may be  
necessary to find your problem.  
Problem: Very weak signals  
If Q1 is defective or incorrectly installed, very little signal energy will reach the  
SA602. If Q2 is defective or installed incorrectly, very little of the SA602's 10.7  
MHz output is getting to the MC3359. Also, be sure that L4 is peaked  
correctly.  
Problem: Considerable frequency drift or shifting  
First, make sure that L3 is soldered securely to the PC board. If you plan to  
use the receiver "on the go", you may wish to secure the base of the coil to  
the board with reinforcing glue. If the receiver drifts, check all wiring and  
components associated with AFC Q3 and pin 11 of the MC3359.  
Problem: Squelch does not function  
Re-check all connections and components associated with pins 10 through 16  
of the MC3359. Check polarity of C27 and D2. C27 sets the time constant for  
the squelch circuit.  
FR6 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOME NOTES FOR ADVANCED USERS  
Unlike Ramsey HF receivers and transmitters, the FR-series of VHF receivers  
do not offer much PC board space or real need for customization or other  
modifications. These receivers do what they are intended to do at the lowest  
price that we are aware of for a tuneable VHF FM receiver with squelch, AFC  
and generous audio output. Therefore, while we are certainly interested in  
hearing about significant performance improvements, we do not recommend  
casual modification attempts.  
However, there is one practical customization which could be undertaken by  
experienced VHF experimenters who wish to take advantage of the SA602's  
ability to accept a crystal resonator instead of the existing L-C tank circuit. The  
goal would be a one channel repeater monitor or dedicated packet receiver.  
Inductor L3 and associated capacitors would be replaced by the appropriate  
crystal tank components. Remember that the crystal oscillator should be  
planned to operate 10.7 MHz. above the desired receiving frequency. Please  
do not attempt such a project unless you have a clear knowledge of oscillator  
design and have reviewed and understood the terms of your Ramsey Kit  
Warranty. We regret that the factory cannot offer any assistance in performing  
this or any other modification, so... you're on your own; but that's what  
experimenting is all about!  
A helpful article on the Signetics NE602 IC, including a discussion of crystal-  
controlled oscillator configurations, was written by Michael A. Covington with  
acknowledged assistance from Signetics personnel, published with good  
circuit illustrations in Radio-Electronics magazine for April 1990 (Vol 61, No  
4). This will help you understand your SA602 IC.  
A less complex approach to the same general goal, eliminating the expense of  
a crystal and the logistics of adding it to the PC board, is to "undo" the  
excellent tuning range we designed into your receiver! This would require  
selecting appropriate values for C9,C10 and C12 and reducing the effect of  
the varactor tuning to perhaps a 100 KHz swing for fine tuning purposes only.  
Try reducing C12 to 1 or 2 pF for starters.  
Finally, the only pin of the MC3359 not used in our circuit is pin 15, for scan  
control. Perhaps you will come up with some fascinating idea for it!  
Again, please be sure that you understand your warranty, and that you  
understand your receiver and how to keep it working, before attempting any  
modifications.  
If you've enjoyed this kit, be sure to check out the entire Ramsey kit line. Call  
or write for our catalog.  
FR6 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Ramsey Kit Warranty  
Please read carefully BEFORE calling or writing in about your kit. Most  
problems can be solved without contacting the factory.  
Notice that this is not a "fine print" warranty. We want you to understand your rights and ours too! All  
Ramsey kits will work if assembled properly. The very fact that your kit includes this new manual is  
your assurance that a team of knowledgeable people have field-tested several "copies" of this kit  
straight from the Ramsey Inventory. If you need help, please read through your manual carefully, all  
information required to properly build and test your kit is contained within the pages!  
1. DEFECTIVE PARTS: It's always easy to blame a part for a problem in your kit, Before you conclude  
that a part may be bad, thoroughly check your work. Today's semiconductors and passive components  
have reached incred bly high reliability levels, and it’s sad to say that our human construction skills  
have not! But on rare occasions a sour component can slip through. All our kit parts carry the Ramsey  
Electronics Warranty that they are free from defects for a full ninety (90) days from the date of  
purchase. Defective parts will be replaced promptly at our expense. If you suspect any part to be  
defective, please mail it to our factory for testing and replacement. Please send only the defective part  
(s), not the entire kit. The part(s) MUST be returned to us in suitable condition for testing. Please be  
aware that testing can usually determine if the part was truly defective or damaged by assembly or  
usage. Don't be afraid of telling us that you 'blew-it', we're all human and in most cases, replacement  
parts are very reasonably priced.  
2. MISSING PARTS: Before assuming a part value is incorrect, check the parts listing carefully to see  
if it is a critical value such as a specific coil or IC, or whether a RANGE of values is suitable (such as  
"100 to 500 uF"). Often times, common sense will solve a mysterious missing part problem. If you're  
missing five 10K ohm resistors and received five extra 1K resistors, you can pretty much be assured  
that the '1K ohm' resistors are actually the 'missing' 10 K parts ("Hum-m-m, I guess the 'red' band  
really does look orange!") Ramsey Electronics project kits are packed with pride in the USA. If you  
believe we packed an incorrect part or omitted a part clearly indicated in your assembly manual as  
supplied with the basic kit by Ramsey, please write or call us with information on the part you need  
and proof of kit purchase  
3. FACTORY REPAIR OF ASSEMBLED KITS:  
To qualify for Ramsey Electronics factory repair, kits MUST:  
1. NOT be assembled with acid core solder or flux.  
2. NOT be modified in any manner.  
3. BE returned in fully-assembled form, not partially assembled.  
4. BE accompanied by the proper repair fee. No repair will be undertaken until we have received the  
MINIMUM repair fee (1/2 hour labor) of $25.00, or authorization to charge it to your credit card  
account.  
5. INCLUDE a description of the problem and legible return address. DO NOT send a separate letter;  
include all correspondence with the unit. Please do not include your own hardware such as  
non-Ramsey cabinets, knobs, cables, external battery packs and the like. Ramsey  
Electronics, Inc., reserves the right to refuse repair on ANY item in which we find excessive  
problems or damage due to construction methods. To assist customers in such situations,  
Ramsey Electronics, Inc., reserves the right to solve their needs on a case-by-case basis.  
The repair is $50.00 per hour, regardless of the cost of the kit. Please understand that our technicians  
are not volunteers and that set-up, testing, diagnosis, repair and repacking and paperwork can take  
nearly an hour of paid employee time on even a simple kit. Of course, if we find that a part was  
defective in manufacture, there will be no charge to repair your kit (But please realize that our  
technicians know the difference between a defective part and parts burned out or damaged through  
improper use or assembly).  
4. REFUNDS: You are given ten (10) days to examine our products. If you are not satisfied, you may  
return your unassembled kit with all the parts and instructions and proof of purchase to the factory for  
a full refund. The return package should be packed securely. Insurance is recommended. Please do  
not cause needless delays, read all information carefully.  
FR6 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FR6 6 Meter FM Receiver Kit  
Quick Reference Page Guide  
Introduction to the FR6 ..................... 4  
Circuit Description............................. 5  
Parts List........................................... 6  
Simplified Block Diagram.................. 8  
Parts Layout Diagram....................... 9  
FR6 Assembly Instructions............... 11  
Testing and Alignment...................... 18  
Enclosure Ideas................................ 20  
Troubleshooting Guide ..................... 21  
Notes for Advanced Users................ 22  
Ramsey Kit Warranty........................ 23  
TOTAL SOLDER POINTS  
REQUIRED TOOLS  
232  
Soldering Iron: Ramsey #RTS06  
ESTIMATED ASSEMBLY  
TIME  
Beginner.............. 6.8 hrs  
Intermediate ........ 3.9 hrs  
Advanced ............ 2.9 hrs  
Thin Rosin Core Solder: Ramsey #RTS12  
Needle Nose Pliers: Ramsey #RTS05  
Small Diagonal Cutters: Ramsey #RTS04  
<OR> Complete Soldering Tool Set: (Radio Shack  
RS64-2801)  
ADDITIONAL SUGGESTED ITEMS  
Soldering Iron Holder/Cleaner: (RS64-2078)  
Holder for PC Board/Parts: Ramsey #RTS13  
Desoldering Braid: Ramsey #RTS08  
Digital Multimeter: Ramsey #M133  
Price: $5.00  
Ramsey Publication No. FR6  
Assembly and Instruction manual for:  
RAMSEY MODEL NO. FR6 6 METER FM RECEIVER KIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Telephone 02A01 User Guide
RCA Universal Remote RCU410MSL User Guide
RCA VCR VR628HF User Guide
Reebok Fitness Treadmill RBTL22920 User Guide
Rosewill Work Light RSL 113 User Guide
Ryobi Trimmer 725rE User Guide
Samsung Cell Phone GH68 03401A User Guide
Samsung DVR SPC 6000 User Guide
Sceptre Technologies Computer Monitor X24 User Guide
Sennheiser Headphones HD 414 User Guide