43-784.fm Page 1 Monday, August 16, 1999 7:47 AM
Cat. No. 43-784
OWNER’S MANUAL
Please read before using this equipment.
TAD-1024
Digital Telephone Answering System
with Dual-Announcement
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 3 Monday, August 16, 1999 7:47 AM
Toll Saver — lets you avoid unneces-
sary long-distance charges when you
call by long-distance to check your mes-
sages.
This TAD is ETL listed to UL standards
and meets all applicable FCC standards.
WARNING: To reduce the risk of
fire or shock hazard, do not ex-
pose this product to rain or mois-
ture.
Room Monitor — lets you listen from a
remote phone to the room where you in-
stalled the TAD.
ANSWER Button — lets you turn the
TAD on or off without disconnecting it.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
Call/Message Counter — shows the
number of messages the TAD has re-
corded.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
DELETE Button — lets you quickly de-
lete messages individually or all at once.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
Remote On/Off — lets you turn the TAD
on or off when you are away from your
home or office.
Phone Pick-Up Detection — stops re-
cording when you pick up any phone on
the same line as the TAD, and resets to
answer the next call.
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
!
Memo Recording — lets you leave
messages for yourself or others in your
home or office.
Note: Your TAD-1024 requires a 9V
battery for memory backup.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 4 Monday, August 16, 1999 7:47 AM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
Your TAD complies with Part 68 of FCC
Rules. You must, upon request, provide
the FCC Registration Number and the
REN to your phone company. Both num-
bers are on the label on the bottom of the
TAD.
Your TAD conforms to federal regula-
tions, and you can connect it to most
telephone lines. However, each device
you connect to the phone line draws
power from the phone line. We refer to
this power draw is the device’s ringer
equivalence number, or REN. The REN
is on the label on the bottom of the TAD.
You must not connect the TAD to any of
the following:
• Coin-operated systems
• Party-line systems
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (or
three in rural areas), your phone(s)
might not ring and your TAD might not
answer. If ringer operation is impaired,
remove a device from the line.
• Most electronic key phone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 5 Monday, August 16, 1999 7:47 AM
CONTENTS
Installation ....................................................................................................... 6
Selecting a Location ................................................................................... 6
Connecting to the Telephone Line ............................................................. 6
Connecting Power ...................................................................................... 6
Installing the Backup Battery ..................................................................... 7
Preparation ...................................................................................................... 8
Setting the Day and Time ........................................................................... 8
Recording the Outgoing Messages ............................................................ 9
Recording the Outgoing Messages ..................................................... 9
Setting the Number of Rings .................................................................... 10
Basic Operation ............................................................................................. 11
Setting the TAD to Answer Calls ............................................................... 11
To Answer and Record ....................................................................... 11
To Announce Only .............................................................................. 11
Recording Incoming Messages ................................................................. 11
Screening Calls ........................................................................................ 12
Playing Messages .................................................................................... 12
Deleting Messages .................................................................................. 13
Recording a Memo ................................................................................... 14
Recording a Conversation ....................................................................... 14
Using Call Break-Through ........................................................................ 15
Changing the CBT Code ................................................................... 15
Changing the Remote Operation Security Code ...................................... 16
Remote Operation ........................................................................................ 17
Remote Answer-On ................................................................................. 17
Using Remote Commands ....................................................................... 18
Troubleshooting ........................................................................................... 19
Resetting the TAD .................................................................................... 19
Care and Maintenance ................................................................................. 20
The FCC Wants You to Know .................................................................. 21
Lightning .................................................................................................. 21
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 6 Monday, August 16, 1999 7:47 AM
INSTALLATION
TEL. LINE Jack
SELECTING A LOCATION
Select a location that is near both a mod-
ular telephone jack and an AC outlet.
Your TAD connects directly to a modu-
lar phone line jack. If the phone line jack
is not a modular jack, you must update
the wiring. You can convert the wiring
yourself, using jacks and adapters avail-
able at your local RadioShack store. Or,
you can let the phone company update
the wiring for you. The USOC number of
the jack to be installed is RJ11C.
You can also connect a telephone to the
TEL. jack on the back of the TAD using a
second modular phone cord (not sup-
plied).
TEL. Jack
CONNECTING TO THE
TELEPHONE LINE
To connect the TAD to the phone line,
plug one end of the supplied modular
cord into the TEL. LINE jack on the back
of the TAD. Then plug the cord’s other
end into a modular phone line jack.
CONNECTING POWER
Insert the supplied adapter’s barrel plug
into the DC 9V jack on the back of the
TAD. Then plug the adapter’s other end
into a standard AC outlet.
DC 9V Jack
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 7 Monday, August 16, 1999 7:47 AM
Caution: The supplied adapter supplies
9 volts AC, delivers at least 400 milli-
amps, and has a plug which properly fits
1. Use a flat-blade screwdriver to lift
the battery compartment cover.
DC 9V
the TAD’s
jack. Using an adapter
that does not meet these specifications
might damage the TAD or the adapter.
When you first connect power, the TAD
beeps once and the message counter
counts up from 0 to 10. Then the TAD
beeps. A1, A2, Lo, CLand 0alternately
appear to indicate that no outgoing mes-
sages are recorded, and the day/time
stamp is not set.
2. Snap the battery’s contacts firmly to
the battery connector, then place
the battery into the compartment.
INSTALLING THE
BACKUP BATTERY
The TAD requires AC power to operate.
However, if AC power fails or you unplug
the TAD-1024, a 9V backup battery (not
supplied) saves the messages and the
settings for the day, time, and security
code. We recommend you use an alka-
line battery, such as RadioShack Cat.
No. 23-553.
3. Replace the cover.
When the battery is low and needs re-
placing, Loappears on the display. Be
sure the AC adapter’s cord is plugged in
so you do not lose the TAD’s stored in-
formation, then replace the battery. After
the battery is installed, A1, A2, CL, and
0alternately appear.
Caution: Always use a fresh battery of
the required size and recommended
type.
Caution: Dispose of old batteries
promptly and properly.
Follow these steps to install the backup
battery.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 8 Monday, August 16, 1999 7:47 AM
PREPARATION
SETTING THE DAY
AND TIME
The TAD records the day and time of the
call with each phone message. Follow
these steps to set the current day and
time.
VOLUME
2. To change the day of the week, re-
peatedly press MEMO/REPEAT to
move backward or CODE/SKIP to
move forward until the TAD an-
nounces the desired day of the
week.
Notes:
• To avoid having to reset the time if
AC power is lost, we recommend
you install a backup battery before
you set the day and time.
• If you do not complete each step
within 8 seconds, the TAD stops
setting and announces the day and
time. Start again from Step 1.
3. Press STOP/TIME SET. The TAD an-
nounces the preset hour.
4. To change the hour, repeatedly
press MEMO/REPEAT to move back-
ward or CODE/SKIP to move forward
to the desired hour.
1. Hold down STOP/TIME SET until the
TAD announces, “Sunday.” CL
(clock) then 01appears on the dis-
play.
5. Press STOP/TIME SET. The TAD an-
nounces the preset minute.
6. To change the minutes, hold down
MEMO/REPEAT to move backward
or CODE/SKIP to move forward to
the desired minute.
7. Press STOP/TIME SET to confirm the
settings. The TAD announces the
day and time and CLdisappears.
VOLUME on the right
side of the TAD to the desired lis-
tening level.
Note: Adjust
To check the current day/time at any
time, press STOP/TIME SET.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 9 Monday, August 16, 1999 7:47 AM
Recording the Outgoing
Messages
RECORDING THE
OUTGOING MESSAGES
1. To record an OGM 1 message, hold
Before you can set the TAD to answer
calls and record messages, you must
record the outgoing message (OGM) the
caller hears when the TAD answers a
call. The TAD-1024 lets you record two
separate messages and it operates dif-
ferently based on which message you
select (see “Setting the TAD to Answer
Calls” on Page 11).
OGM 1
down
until the TAD beeps
and A1(Announcement 1) appears.
OGM 1
•
plays the message you re-
corded, and lets the caller leave a
message of up to 60 seconds.
To record an OGM 2 message, hold
OGM 2
down
until the TAD beeps
OGM 2
•
(announcement only) plays
and A2(Announcement 2) appears.
the message you recorded, but
hangs up without letting the caller
leave a message. This is useful for
announcing information about an
upcoming event. Be sure the
announcement clearly states that
the caller cannot leave a message.
If
the
TAD-1024’s
memory
2. Speak in a normal voice about 8
inches away from the microphone
(located on the front of the TAD). If
you recording the OGM 1 message,
ask for the caller’s name, phone
number, and message.
becomes full, it will automatically
switch from OGM 1 to OGM 2 and
play that message for any new
calls.
Note: The maximum length for each out-
going message is 32 seconds. As you
record, the display counts down the re-
maining recording time.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 10 Monday, August 16, 1999 7:47 AM
Important: Do not tell callers that
you are not home. Instead, say that
you cannot come to the phone right
now.
SETTING THE NUMBER
OF RINGS
The ring select switch on the back of the
TAD controls how long the TAD waits
before it answers a call. Slide the switch
to the appropriate position.
3. When you finish recording, press
STOP/TIME SET.
The TAD automati-
cally plays back the outgoing mes-
sage.
To play back your outgoing OGM 1 mes-
OGM 1
sage at any time, press
. A1ap-
pears, the TAD beeps, and the outgoing
message plays.
To play back your OGM 2 message at
2
4
7
— The TAD answers after two rings.
— The TAD answers after four rings.
— The TAD answers after seven rings.
OGM 2
any time, press
, A2appears, the
TAD beeps, and the announcement-only
message plays.
T.S.
(Toll Saver) — If there are new mes-
sages, the TAD answers after two rings.
Otherwise, the TAD answers after four
rings. This lets you avoid unnecessary
charges when calling by long-distance to
check your messages. If you hear more
than two rings, you know you can hang
up because the TAD has no new mes-
sages.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 11 Monday, August 16, 1999 7:47 AM
BASIC OPERATION
To turn off the TAD so it does not answer
calls, press ANSWER again. OFappears
for a few seconds and the power indica-
tor turns off.
SETTING THE TAD TO
ANSWER CALLS
To Answer and Record
To turn on the TAD and set it to answer
calls and record messages, press AN-
SWER once. The TAD beeps, and briefly
displays On, and the power indicator
lights. The TAD is now set to answer
calls using the OGM 1 message and
record callers’ messages.
RECORDING INCOMING
MESSAGES
The maximum incoming message re-
cording length is 60 seconds. When a re-
cording reaches 55 seconds, the TAD
beeps once to notify the caller that time
will soon be up. When the recording
reaches 60 seconds, the TAD sounds a
long beep, then hangs up.
Power
Indicator
The TAD hangs up and resets to answer
the next call when:
• The caller hangs up.
To Announce Only
• The maximum message length (60
seconds) is reached.
To turn on the TAD and set it to answer
calls, but not record messages, press
ANSWER so the power indicator lights.
Then hold down ANSWER until the TAD
beeps. Ao(announcement only) and the
number of recorded messages alter-
nately appear. The TAD is now set to an-
swer calls using the OGM 2 message
without recording callers’ messages.
• There are more than 8 seconds of
silence.
• You pick up any phone on the same
line as the TAD (see “Screening
Calls” on Page 12).
If the TAD’s memory is full (FLappears),
the TAD answers the call after 8 rings
and plays the announcement-only mes-
sage (OGM 2).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 12 Monday, August 16, 1999 7:47 AM
message number and the day and time
the message was recorded, and then
plays the message.
SCREENING CALLS
To screen calls, let the TAD answer
them, then listen to the caller’s message
through the TAD’s speaker. If you de-
cide to answer the call, pick up any
phone on the same phone line as the
TAD. The TAD stops recording and re-
sets to answer the next call.
To play only new messages, hold down
PLAY
for 2 seconds. (If there are no new
messages stored, the TAD says, “You
have no new messages.”)
Note: If you pick up the phone just as the
TAD answers, the TAD might not stop
playing the outgoing message. If this
STOP/
happens, press on the phone or
TIME SET
on the TAD.
VOLUME
To adjust the volume, rotate
on the side of the TAD.
If you do not want to take the call, do not
pick up the phone, and let the TAD finish
recording the caller’s message.
After all messages play, the TAD says,
“End of message(s)” and saves all the
messages.
VOLUME
To adjust the volume, rotate
on the side of the TAD.
To replay a message while you are lis-
MEMO/REPEAT
tening to it, press
. The
current message starts again from the
beginning.
PLAYING MESSAGES
The display shows the total number of
messages. If there are new messages,
the power indicator also flashes until all
new messages have been played.
To play all the messages (old and new),
PLAY
press
. The TAD announces the
number of messages recorded, each
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 13 Monday, August 16, 1999 7:47 AM
To return to the previous message dur-
ing playback, press MEMO/REPEAT
twice. The previous recorded message
plays.
To stop playback at any time, press
STOP/TIME SET. The TAD beeps and re-
sets to answer calls.
To skip to the next message during play-
back, press CODE/SKIP once. The next
recorded message plays.
DELETING MESSAGES
To delete a specific message, press DE-
LETE once while the message is playing.
The TAD beeps once and dL (delete)
briefly appears. The TAD deletes the
current message, then plays the next.
To pause while listening to messages,
press PLAY. PS(pause) appears on the
display. To resume playback, press
PLAY again within 60 seconds. Other-
wise, the TAD beeps twice, stops play-
back and displays the total number of
messages.
To delete all messages, hold down DE-
LETE while playback is stopped. The
TAD sounds a long beep and dL ap-
pears. The TAD deletes all messages
except those that have not been played.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 14 Monday, August 16, 1999 7:47 AM
RECORDING A MEMO
RECORDING A
CONVERSATION
A memo is a message you can record by
speaking directly into the TAD, without
having to call in on the phone.
You can record both sides of a conver-
sation on any phone connected to the
same phone line as the TAD.
Follow these steps to record a memo up
to 60 seconds long.
Note: It is illegal in some areas to record
a conversation without the consent of all
parties to the conversation, including the
phone company. Check the laws in your
area before you use the two-way record-
ing feature.
MEMO/REPEAT
1. Press
until oo ap-
pears. The TAD sounds a long beep
and 60appears. Speak into the mi-
crophone in a normal voice. The
display shows how much time is left
for recording.
MEMO/REPEAT
Hold down
until the TAD
sounds a long beep. 2R (two-way re-
cording) appears and recording begins.
STOP/
The TAD records until you press
TIME SET
, or there is 30 seconds of si-
lence, or 8 seconds of a busy signal.
2. The TAD automatically stops re-
cording after 60 seconds or you can
STOP/TIME SET
press
when you fin-
ish the memo. The TAD beeps
once, and the message number in-
dicator increases by one.
To play back a recorded call, simply play
back your messages.
The memo is stored along with the in-
coming messages. To hear the memo,
simply play back your messages.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 15 Monday, August 16, 1999 7:47 AM
MEMO/REPEAT.
2. Press
Cc appears
USING CALL BREAK-
THROUGH
followed by the digits of the preset
CBT code in sequence, then the
first digit reappears. For example,
when the security code is 168, the
If you screen your calls but want to be
sure to know when calls come in from
certain people, give those people your
call breakthrough (CBT) code. Tell them
to enter the code during the outgoing
message.
–
display shows Cc, 1, –6, 8, then
–
–
1reappears.
SKIP/CODE
3. Repeatedly press
or
MEMO/REPEAT
to set the first digit,
. The second
ANSWER
then press
When a caller enters the CBT code, the
TAD alerts you with two beeps, then it
pauses for 40 seconds. Then the TAD
sounds one beep every second for 5
seconds. To answer the call within the
45-second alert, pick up the handset. If
you do not answer, the caller can leave
a message after a long beep sounds.
digit appears.
Note: If you enter an incorrect digit,
STOP/TIME SET
press
, then repeat
the procedure.
SKIP/CODE
MEMO/REPEAT
or
4. Press
to set the second digit, then press
ANSWER
. The third digit appears.
SKIP/CODE MEMO/REPEAT
5. Press
or
Note: CBT works only when you use the
OGM 1 message.
AN-
to set the third digit, then press
SWER
. The TAD sounds a long
beep.
Changing the CBT Code
The CBT code is preset to 168, but you
can change it by following these steps.
CODE/SKIP
1. Hold down
until the TAD
beeps once. Coappears.
Note: If you do not complete each
of the following steps within 8 sec-
onds, the TAD stops setting the
code. Start again from Step 1.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 16 Monday, August 16, 1999 7:47 AM
Note: If you enter an incorrect digit,
CHANGING THE REMOTE
OPERATION SECURITY
CODE
STOP/TIME SET
press
the procedure.
, then repeat
SKIP/CODE
MEMO/REPEAT
or
4. Press
to set the second digit, then press
ANSWER
The remote operation security code is
preset to 784, but you can change it by
following these steps.
. The third digit appears.
SKIP/CODE MEMO/REPEAT
5. Press
or
AN-
to set the third digit, then press
SWER
beep.
Note: Be sure to set each digit within 8
seconds. Otherwise, you must start over
from Step 1.
. The TAD sounds a long
CODE/SKIP
1. Hold down
until the TAD
To check the remote operation security
code at any time, follow Steps 1 and 2,
beeps once. Coappears.
STOP/TIME SET
then press
to exit.
CODE/SKIP
2. Press
again. Sc(securi-
ty code) and the digits of the current
code appear in sequence, then the
first digit reappears.
For example, when the security
code is 784, the display shows Sc
–
–
(security code), 7, –8, 4, then
7reappears.
–
SKIP/CODE
3. Repeatedly press
or
MEMO/REPEAT
to set the first digit,
. The second
ANSWER
then press
digit appears.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 17 Monday, August 16, 1999 7:47 AM
REMOTE OPERATION
You can operate the TAD from almost
any touch-tone phone, or from a rotary
phone using a pocket tone-dialer (avail-
able at your local RadioShack store).
REMOTE ANSWER-ON
Note: An outgoing message must be re-
corded before you can remotely set the
TAD to answer calls.
Notes:
To set the TAD to answer calls, dial your
phone number. The TAD answers the
call after 10 rings and sounds two beeps.
• When the memory is full, the TAD
answers the call after eight rings
and plays OGM 2 (the announce-
ment-only message).
Enter the remote operation security
code within 8 seconds. The TAD sounds
one long and one short beep and plays
the OGM 1 message.
• To bypass the outgoing message
and begin recording a message im-
mediately when you call the TAD
from a remote phone, you can
press # during the announcement.
The TAD skips the rest of the an-
nouncement, beeps once, and be-
gins recording.
You can hang up at this point and the
TAD is set to answer calls. Or, you can
now enter other remote command(s).
If the TAD records over 8 seconds of si-
lence, it automatically disconnects.
• If the TAD is set to toll saver, it an-
swers after two rings if you have
new messages (ones you have not
played). If there are no new mes-
sages, the TAD waits for four rings
before it answers. This gives you
time to hang up before the TAD an-
swers so you can avoid unneces-
sary long-distance charges. See
“Setting the Number of Rings” on
Page 10.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 18 Monday, August 16, 1999 7:47 AM
USING REMOTE
COMMANDS
Press:
To:
82
91
92
#1
Play OGM 1.
Change OGM 2.
Play OGM 2.
To use the remote commands, you must
enter the remote operation security code
within 8 seconds after the TAD answers
the call. After the TAD beeps once to
verify you entered the code correctly,
enter the number(s) for the function(s)
you want the TAD to perform.
Change remote operation secu-
rity code.
#2
#
Change CBT Code.
Skip OGM 1 during playback.
After you press 2 or 3:
Press:
To:
Turn the TAD off.
Press:
To:
00
01
5
Delete the current
message.
Turn the TAD on. The TAD beeps
and plays OGM 1. (TAD is set to
play OGM 1.)
1 while message Replay the previous
number and day/ message.
time is playing
02
Set TAD to answer with OGM 2
announcement.
1 during message Replay the current
2
3
4
Play all messages.
Play new messages.
playback
message.
3
Skip forward to the
next message.
Monitor the room where the TAD
is installed. The room is moni-
tored for 15 seconds. Press 4
again for another 15 seconds.
You can repeat this for as long as
you like.
6
Stop message play-
back.
51
6
Delete all messages (except new
messages).
Stop playback and message
recording.
7
Record a memo.
Change OGM 1.
81
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 19 Monday, August 16, 1999 7:47 AM
TROUBLESHOOTING
If you experience problems with your TAD, try the suggestions in this section. If
you still have problems, contact your local RadioShack store for assistance.
Problem
Remedy
The incoming message is incomplete. Be sure the memory is not full.
The incoming message is unclear.
Be sure VOLUME is set to the desired sound
level.
The TAD does not answer after two,
four, or seven rings.
Be sure the TAD is set to answer calls.
Lo flashes on the display.
The backup battery is weak. Replace the bat-
tery (see “Installing the Backup Battery” on
Page 7).
The TAD does not respond to the
remote operation security code.
Make sure the phone you used to dial the TAD
is a touch-tone phone.
Re-enter your remote operation security code,
pressing each button for 2 seconds.
The remote operation security code might have
reset to the default code due to a power failure.
Make sure the remote operation security code
you entered is correct.
RESETTING THE TAD
If your TAD stops working properly, use a
straightened paper clip to press RESET on
the left side of the TAD to reset the answer-
ing machine.
Note: The outgoing message and all information stored in memory are erased
when you press RESET.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 20 Monday, August 16, 1999 7:47 AM
CARE AND MAINTENANCE
Your RadioShack TAD-1024 Digital Telephone Answering System with Dual-An-
nouncements is an example of superior design and craftsmanship. The following
suggestions will help you care for the TAD so you can enjoy it for years.
Keep the TAD dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Handle the TAD gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the TAD to work improperly.
Use and store the TAD only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices
and distort or melt plastic parts.
Keep the TAD away from dust and dirt, which can cause prema-
ture wear of parts.
Wipe the TAD with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong de-
tergents to clean the TAD.
Modifying or tampering with the TAD’s internal components can cause a mal-
function and might invalidate your TAD’s warranty. If your TAD-1024 is not per-
forming as it should, take it to your local RadioShack store for assistance. If the
trouble is affecting the telephone lines, the phone company can ask you to dis-
connect your TAD-1024 until you have resolved the problem.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 21 Monday, August 16, 1999 7:47 AM
To eliminate interference, you can try
one or more of the following corrective
measures:
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your TAD caus-
es problems on the telephone line, the
telephone company attempts to notify
you in advance. If advance notice is not
practical, the telephone company noti-
fies you as soon as possible and advises
you of your right to file a complaint with
the FCC.
• Reorient or relocate the receiving
radio or TV antenna.
• Increase the distance between the
TAD and the radio or TV.
• Use outlets on different electrical
circuits for the TAD and the radio or
TV.
Also, the telephone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this TAD. The telephone
company notifies you of these changes
in advance so you can take the neces-
sary steps to prevent interruption of your
telephone services.
Consult your local RadioShack store if
the problem still exists.
LIGHTNING
Your TAD has built-in protection circuits
to reduce the risk of damage from surg-
es in telephone and power line current.
These protection circuits meet or exceed
the FCC requirements. However, light-
ning striking the telephone or power
lines can damage your TAD.
Your TAD complies with the limits for a
Class B digital device as specified in
Part 15 of FCC Rules. These limits pro-
vide reasonable protection against radio
and TV interference in a residential area.
However, your TAD might cause TV or
radio interference even when it is oper-
ating properly.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug the TAD during storms
to reduce the possibility of damage.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 22 Monday, August 16, 1999 7:47 AM
NOTES
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 23 Monday, August 16, 1999 7:47 AM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-784.fm Page 24 Monday, August 16, 1999 7:47 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RADIOSHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
10A7
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|