Indoor IR Dome Cameras
Manual
Model No.
Resolution
Lens Size
NTSC
EV-2221-N3BQ
EV-2221-NKBQ
EV-2801-N3BQ
EV-2801-NKBQ
420 TV lines
3.6mm
420 TV lines 2.8~11mm DC auto iris
540 TV lines 3.6mm
540 TV lines 2.8~11mm DC auto iris
PAL
EV-2221-P3BQ
EV-2221-PKBQ
EV-2801-P3BQ
EV-2801-PKBQ
420 TV lines
420 TV lines 2.8~11mm DC auto iris
540 TV lines 3.6mm
540 TV lines 2.8~11mm DC auto iris
3.6mm
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM Indoor IR Dome Cameras
Overview:
Latch
Arrow
Important:
Do not cut the DC jack or the female BNC
connector as this will void the warranty.
To remove the
mounting base,
release the latch.
Mounting base
Camera
Camera cover
Dome cover
Mounting
screws
Punch-out
Female BNC
connector
DC plug with
terminal block
Varifocal models only
Focus
Zoom
DC jack
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
6. Do not open or disassemble the camera. There are no
user-serviceable parts inside.
2. Use the camera within given temperature and
electrical limits.
7. Do not drop the camera or subject it to strong vibrations.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.*
Note: Many video monitors produce strong
electromagnetic fields close to the display CRT, especially
when the monitor is turned on or during de-gaussing,
which occurs automatically with many monitors when the
monitor is turned on.
Installation:
7. Mount the mounting base by using the three included
mounting screws to secure it to the wall. If the wall is
made of drywall, brick, or similar material, it may be
necessary to also use the three included screw anchors.
8. Secure the camera by lining it up with the base and turning
the camera clockwise. To line up, make sure the gap in the
mounting base is aligned with the wiring notch. The
camera will click when locked into place.
1. Run hidden cables from the video source and 12VDC
power supply to the camera. Connect to the DC jack
and female BNC connectors. Do not cut the DC jack
or the female BNC connector as this will void the
warranty. If needed, use the included SECO-LARM
DC plug with terminal block.
2. Test to make sure the voltage is correct.
Use only 12VDC.
9. Adjust camera angle as shown on page 2, Adjusting the
Camera Angle.
10. Test the video signal.
11. Varifocal models only: Adjust the zoom and focus by
hand or with a small screwdriver to loosen the knob, and
then sliding the knob left or right. IMPORTANT: Do not
use power tools. Lens damage may result.
12. Reattach the dome to the camera by giving the dome a
slight twist. The dome will click when locked into place.
13. Do a final test of the video camera and monitor.
3. Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location
with a pencil.
4. Remove the dome from the camera by twisting it
counterclockwise.
5. Remove the mounting base by releasing the latch
indicated by white arrow on the inner rim of the
camera.
6. If flush mounting, remove the punch-out in the base
and run the wires through the center of the base.
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM Indoor IR Dome Cameras
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
IMPORTANT
Check that the correct power supply is in use.
Check that the correct power supply is in use.
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for
a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
E-mail: [email protected]
PICSN4
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
MiEV-2xx1-NxBQ_1012.docx
4
SECO-LARM U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|