Radio Shack Speaker 40 4091 User Guide

3
7 16/+PEJ"4/9C["%GKNKPI"5RGCMGT  
40-4091  
OWNER’S MANUAL — Please read before using this equipment.  
1
4
Your RadioShack 5 / -Inch 2-Way Ceiling  
your speaker flush with the ceiling or wall,  
making it ideal for unobtrusive use in a  
surround-sound system. The frame and grille  
can also be painted to match the room’s  
decor.  
"+/2146#06"  
#
#
1
4
Speaker features a crossover, a 5 / -inch  
woofer for rich lows, and a / -inch tweeter  
for crisp highs. The speaker can handle up to  
40 watts of music power. The wing-type  
mounting system makes it easy to mount  
1
If an icon appears at the end of a paragraph, go  
to the box on that page with the corresponding  
icon for pertinent information.  
2
— Warning  
— Important  
#
Rý  
. — Caution  
° — Hint  
± — Note  
+056#..#6+10  
24'2#4+0)"6*'".1%#6+10  
To mount your speaker, you need the  
following items (not supplied, available at  
your local RadioShack or online at  
RadioShack.com).  
24'2#4+0)"6*'"52'#-'4  
If you choose to paint the frame and grille,  
paint them and let them dry before you  
connect the speaker wire or mount the  
speaker.  
• drywall or keyhole saw  
• wire stripper  
To remove the grille for painting, insert a  
paper clip into one of the grille openings, then  
pull up. Or, you can carefully twist the plastic  
frame back and forth until the grille edge  
becomes exposed, then lift the grille to  
remove it.  
• Phillips screwdriver  
• pencil or marker  
• 18–20 gauge speaker wire  
1. Be sure the mounting surface is between  
3
1
8
4-  
/ inch and 1 / inch thick, with at least a  
4
3
2 / -inch clearance behind the mounting  
surface and no wall studs or other  
objects to block the back of the speaker.  
2. Remove the inner cardboard disc from  
the supplied template/paint mask and  
keep it for later. Use the outer portion as  
a template to mark the cutout hole size  
and location for mounting the speaker.  
Carefully remove the dust cloth from behind  
the grill and replace it after you are finished  
painting.±  
±"016'"±"  
Do not paint the speaker element. We  
recommend you spray-paint the grille so paint  
does not block the holes.  
You can also paint the frame to match your  
wall or ceiling. To prevent paint from entering  
the speaker, remove the grille and insert the  
supplied cardboard paint mask. After the  
paint is dry, remove the paint mask and  
replace the grille.  
Paint Mask  
3. Use a drywall or keyhole saw to cut the  
."%#76+10".  
Be sure not to cut into any existing wiring or  
hole..  
plumbing hidden behind the wall.  
%100'%6+0)"6*'"52'#-'4"9+4'5  
Your local RadioShack store sells a wide  
selection of speaker wire. We recommend  
you use wire that is color-coded or marked on  
one side to help you connect the wire  
correctly.  
2. Separate about 4 inches of speaker wire  
at each end.  
±"016'5"±"  
1
/4 inch  
Avoid routing the speaker wire near electrical  
wires.  
1. Route the speaker wire to the speaker  
from the receiver.±  
4 inches  
Do not nail or staple the speaker wire.  
© 2002 RadioShack Corporation.  
All Rights Reserved.  
RadioShack and RadioShack.com are trademarks  
used by RadioShack Corporation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ricoh Network Card BB HPL10A R User Guide
RIDGID Saw 122XL User Guide
Roadmax GPS Receiver VMAX361 User Guide
Rockford Fosgate Stereo Amplifier 3606 User Guide
Russell Hobbs Microwave Oven RHM2011 User Guide
Saab Patio Heater B205 User Guide
Samsung Stereo System MAX DC20800 User Guide
Scion Car Stereo System AM FM CD Player User Guide
Sears Cooktop 790428 User Guide
Sears Elliptical Trainer 831239530 User Guide