Radio Shack Flat Panel Television 16 3011 User Guide

Rod Antenna — provides  
adequate reception in most  
metropolitan areas  
EXT. ANT. Jack - Lets you  
connect an external antenna  
for optimum reception in  
weak signal areas.  
Optional Accessories  
Flat LCD - makes the TV more  
compact and uses less power  
than a standard picture tube.  
2.5” TFT LCD TV  
16-3011  
Tuning Ý /Þ - Press the  
control to adjust the TV to the  
desired channel.  
TV/Sound — lets you listen to  
audio only when TV reception  
is poor, or to conserve battery  
6V Vehicle DC Adapter  
Earphones  
Power  
BATTERY POWER  
Stand - Use the stand to lean  
the TV against flat surfaces.  
Your TV requires four AAA batteries (not supplied).  
You may purchase alkaline batteries from your local  
RadioShack store.  
Volume - Turn the dial to  
adjust the volume level.  
Size B Adaptaplug  
6V AC to DC Adapter  
1. Slide off the battery compartment cover.  
2. Insert the batteries into the compartment  
as indicated by the polarity symbols (+ and –)  
marked inside.  
Bright - Turn dial to adjust  
the brightness level.  
Ear Jack - Lets you enjoy  
private listening with an  
optional earphone.  
3. Replace the cover.  
Notes:  
Alkaline Batteries  
• The TV can operate for about 2 hours (3.5 for audio only mode) with alkaline  
batteries. When the sound level lowers or the picture becomes unstable, replace the  
batteries.  
Using Your TV  
1. Extend the rod antenna and slide UHF/VHF/OFF to VHF or UHF. The TV starts scanning and  
• The TV’s internal batteries automatically disconnect when you connect an adapter.  
stops at the next active channel in the selected band.  
AC POWER  
2. Press  
TUNING  
to tune to a different channel. The tuning line on the screen aligns with  
You can power the TV using a regulated 6V AC adapter of at  
least 400 mA, and a size B Adaptaplug™ adapter (neither  
supplied). Both are available at your local RadioShack store.  
TV/SOUND  
VOLUME  
the selected channel number below the screen.  
3. To adjust the volume, rotate VOLUME located on the right side of the TV.  
4. To adjust the picture to the desired brightness, rotate BRIGHT located on the right side of the  
TV. The brightness also changes with the screen’s angle.  
5. To save battery power, turn off the display and listen to audio only by setting TV/SOUND to  
SOUND.  
UHF/VHF/OFF  
Set the adapter’s voltage switch to 6V. Insert the Adaptaplug into  
the adapter’s cord, aligning + with TIP. Plug the Adaptaplug’s  
barrel plug into the TV’s DC IN 6V jack. Then, plug the other end  
of the AC adapter cord into a standard AC outlet.  
AUDIO/VIDEO  
DC IN 6V Jack  
BACKLIGHT  
In low temperatures, the TV screen takes a few seconds to light, or it might be slightly red in color.  
This is not a malfunction. Normal operation resumes after a few seconds.  
BRIGHT  
Note: The adapter might become warm after extended periods  
of use.  
EAR Jack  
USING AN EARPHONE  
For private listening, you can connect an optional earphone with a /8-inch plug to the EAR jack.  
This automatically mutes the built-in speaker.  
USING VEHICLE BATTERY POWER  
1
You can power the TV from a vehicle’s 12V power source (such as a cigarette-lighter  
socket) using a 6V, 400-mA DC adapter and a size B Adaptaplug™ adapter (neither  
supplied).  
Cautions:  
• Set VOLUME to the lowest setting before you begin listening. Then adjust the volume to a comfortable level.  
• Do not use an earphone when operating a vehicle or riding a bicycle. This can cause a traffic hazard and can be illegal in  
some areas.  
Set the adapter’s voltage switch to 6V. Insert the Adaptaplug into the adapter’s cord,  
aligning + with TIP. Plug the Adaptaplug’s barrel plug into the TV’s DC IN 6V jack. Unplug  
the vehicle’s cigarette lighter and plug the large end of the DC adapter cord into the  
cigarette-lighter socket.  
USING THE TV AS A MONITOR  
You can play back the signal from an audio/video component connected to your TV’s AUDIO/VIDEO jack. You will need a  
Y-adapter cable (not supplied), available at your local RadioShack store. Connect the cable’s red plug to the component’s video  
output jack, and its white plug to the component’s audio output jack. Then, plug the cable’s mini plug into the TV’s AUDIO/VIDEO  
jack.  
Note: If the TV does not operate properly when you use DC power, be sure the cigarette-  
lighter socket is clean and that the adapter’s plug is properly connected to the socket.  
Note: Connecting an audio/video component disables the TV’s antenna.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

PYLE Audio TV Receiver PLTVATSC1 User Guide
Radio Shack Stereo Amplifier MPA 125 User Guide
Raritan Computer Marine Radio CC WSAPI 0B v510 E User Guide
RCA Universal Remote RCU800B User Guide
Roland Electronic Keyboard RP201 User Guide
Rolls Music Mixer MX442 User Guide
Royal Consumer Information Products Outdoor Fireplace U19023 User Guide
Ryobi Saw CSB132L User Guide
Sanyo Digital Camera VPC S1415 User Guide
Senco Air Compressor PC2002 User Guide