43-1099.fm Page 1 Tuesday, August 17, 1999 4:19 PM
Cat. No. 43-1099
OWNER’S MANUAL
Please read before using this equipment.
ET-929
900 MHz Cordless Telephone
with Caller ID/Call Waiting ID
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 3 Tuesday, August 17, 1999 4:19 PM
Important Caller ID Information
Autotalk — you can set the ET-929 so
you can answer a call simply by lifting
the handset from the base.
To use the phone’s Caller ID and Call
Waiting with Caller ID features, you
must be in an area where those services
are available and you must subscribe to
those services through your local phone
company.
Tone or Pulse Dialing — lets you use
your phone with tone or pulse (rotary) di-
aling and lets you switch from pulse to
tone dialing for long-distance, bank-by-
phone, or other special services.
Where Caller ID is offered, one or more
options are generally available:
Super CCT Noise-Reduction Circuitry
— provides clear telephone conversa-
tions with sound clarity comparable to
that of a corded phone.
• caller’s number only
• caller’s name only
• caller’s name and number
Redial — lets you quickly redial the last
number dialed.
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
Flash — sends an electronic switch-
hook signal for use with special phone
services, such as Call Waiting.
Hearing-Aid Compatibility — lets you
use the ET-929 with hearing aids that
have a T (telephone) switch.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
Serial Number: __________________
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 4 Tuesday, August 17, 1999 4:19 PM
Important:
FCC STATEMENT
• Cordless phones such as this one
require AC power to operate. When
the power is off, you cannot make or
receive calls using your ET-929. To
be safe, you should also have a
phone that does not need AC power
to operate (not a cordless phone),
so you can still make and receive
calls if there is an AC power failure.
Your ET-929 complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC registration number
and the REN to your phone company.
These numbers are on the bottom of the
base.
Note: You must not connect your phone
to any of the following:
• Your phone operates on standard
radio frequencies as allocated by
the FCC. It is possible for other ra-
dio units operating nearby on similar
frequencies to unintentionally inter-
cept your conversation or cause in-
terference. This possible lack of
privacy can occur with any cordless
phone.
• coin-operated systems
• party-line systems
• most electronic key phone systems
The ET-929 complies with the limits for
a Class B digital device as specified in
Part 15 of FCC Rules. These limits pro-
vide reasonable protection against ra-
dio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly. To elimi-
nate interference, you can try one or
more of the following corrective mea-
sures:
READ THIS BEFORE
INSTALLATION
Your ET-929 conforms to federal regula-
tions, and you can connect it to most
telephone lines. However, each device
that you connect to the telephone line
draws power from the line. We refer to
this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the bottom of the base.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical cir-
cuits for the equipment and the ra-
dio or TV.
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five, your
phones might not ring. In rural areas, a
total REN of three might impair ringer
operation. If ringer operation is impaired,
remove a device from the line.
Consult your local RadioShack store if
the problem still exists.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 5 Tuesday, August 17, 1999 4:19 PM
CONTENTS
Installation ............................................................................................................ 6
Mounting the Phone ........................................................................................ 6
On a Desk ................................................................................................. 6
On a Wall Plate ......................................................................................... 7
Directly On a Wall ..................................................................................... 8
Connecting and Charging the Battery Pack .................................................... 9
Setting the Dialing Mode ............................................................................... 11
Setting the Ringer’s Tone and Volume .......................................................... 12
Turning Autotalk On/Off ................................................................................. 12
Storing Your Area Code ................................................................................ 13
Setting Caller ID with Call Waiting ................................................................. 13
Operation ............................................................................................................ 14
Making Calls .................................................................................................. 14
Answering Calls ............................................................................................. 14
Setting the Handset Volume .......................................................................... 14
Changing the Channel ................................................................................... 14
Using REDIAL ............................................................................................... 15
Using FLASH ................................................................................................. 15
Using Tone Services on a Pulse Line ............................................................ 15
Paging ........................................................................................................... 16
Memory Dialing ............................................................................................. 16
Storing a Number and Name in Memory ................................................ 16
Editing or Deleting a Memory Number .................................................... 18
Entering a Pause .................................................................................... 18
Dialing a Memory Number ...................................................................... 18
Chain-Dialing Service Numbers .............................................................. 19
Testing Stored Emergency Numbers ...................................................... 19
Using a Headset ............................................................................................ 19
Caller ID Operation ............................................................................................ 20
Reviewing Caller ID Records ........................................................................ 20
Caller ID Messages ................................................................................ 21
Dialing from a Caller ID Record ..................................................................... 21
Storing a Caller ID Record to Memory .......................................................... 22
Deleting Caller ID Records ............................................................................ 22
Troubleshooting ................................................................................................. 23
Care and Maintenance ....................................................................................... 25
Replacing the Battery Pack ........................................................................... 26
The FCC Wants You to Know ........................................................................ 27
Lightning ........................................................................................................ 27
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 6 Tuesday, August 17, 1999 4:19 PM
INSTALLATION
On a Desk
MOUNTING THE PHONE
Follow these steps when you place the
base on a desk or table.
You can place the phone on a desk or
table, mount it on a standard wall plate,
or mount it directly on a wall.
1. Insert the bracket’s tabs into the
base’s upper tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
Select a location that is:
• near an AC outlet
• near a telephone line jack
• out of the way of normal activities
Clip Slots
Clips
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
Upper Tab Slots
The base’s location affects the hand-
set’s range. If you have a choice of sev-
eral locations, try each to see which
provides the best performance.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
Caution: The supplied AC adapter was
designed specifically for your ET-929.
Use only the supplied adapter.
Notes:
• Your telephone connects directly to
a modular phone line jack. If your
phone line jack is not a modular
jack, you can update the wiring
yourself, using jacks and adapters
available from your local Ra-
dioShack store. Or, you can let the
telephone company update the wir-
ing for you.
3. Plug the modular cord’s other end
into a modular phone line jack.
• The USOC number of the jack to be
installed is RJ11C, or RJ11W for a
wall plate jack.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 7 Tuesday, August 17, 1999 4:19 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
Lower
Tab
Slots
Tabs
Clip Slots
5. Route the adapter’s cord through
the strain relief slot on the bracket.
2. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base.
Strain
Relief Slot
6. Plug the adapter into a standard AC
outlet.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
7. Lift the base’s antenna to a vertical
position.
4. Route the adapter’s cord through
the narrow groove on the bottom of
the bracket.
On a Wall Plate
1. Insert the bracket’s tabs into the
base’s lower tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
Narrow
Groove
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 8 Tuesday, August 17, 1999 4:19 PM
5. Plug the modular cord into the wall
plate jack, then align the bracket’s
keyhole slots with the wall plate
studs and slide the base downward
to secure it.
Directly On a Wall
For this mounting method, you need two
screws (not supplied) with heads that fit
into the keyhole slots on the bottom of
the base.
5/16"
1. Drill two holes 315/16
inches (100 mm)
apart. Then thread a
15/16"
screw into each hole,
letting the heads ex-
tend about /16 inch (8
3
5
mm) from the wall.
6. Plug the adapter into a standard AC
outlet.
2. Insert the bracket’s tabs into the
base’s lower tab slots as shown,
then press down on the bracket’s
clips and insert them into the clip
slots.
Lower
Tab
Slots
Tabs
7. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place.
Clip Slots
3. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
8. Lift the base’s antenna to a vertical
position.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 9 Tuesday, August 17, 1999 4:19 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
8. Plug the adapter into a standard AC
outlet.
5. Route the modular and adapter
cords through the grooves on the
bottom of the bracket.
9. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place.
Grooves
6. Align the keyhole slots with the
mounting screws and slide the base
downward to secure it.
10. Lift the base’s antenna to a vertical
position.
CONNECTING AND
CHARGING THE BATTERY
PACK
The ET-929 comes with a rechargeable
nickel-cadmium battery pack in the
handset, but not connected. Before us-
ing your phone, you must connect the
battery pack, then charge it for about 14
hours.
7. Plug the modular cord into a modu-
lar phone line jack.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 10 Tuesday, August 17, 1999 4:19 PM
1. Press down and slide off the battery
pack compartment cover as shown.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone (5
TALK
short beeps) when you press
.
If this happens, return the handset
to the base for about 5 seconds.
This resets the security access-
protection code.
2. Unfasten the retainer strap and lift
the battery pack out of the compart-
ment.
• If the CHARGE indicator does not
light when you place the handset on
the base, be sure the battery pack
and AC adapter are correctly and
securely connected.
Also, check the charging contacts
on the handset and base. If the con-
tacts are dirty or tarnished, clean
them with a pencil eraser.
3. Plug the battery pack’s connector in-
to the socket in the compartment
(the connector fits only one way),
then replace the battery pack and
fasten the retainer strap.
4. Replace the cover.
To charge the battery pack, place the
handset either faceup or facedown on
the base. The CHARGE indicator on the
base lights.
CHARGE
Indicator
• If the battery pack becomes com-
pletely discharged or the base loses
power while the handset is away,
the security access-protection code
needs to be reset. To reset the code,
return the handset to the base for
about 5 seconds. If it was the hand-
set that lost power, leave the hand-
set on the base to recharge the
battery pack
Recharge the battery pack when RE-
CHARGE NOWand
play.
flash on the dis-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 11 Tuesday, August 17, 1999 4:19 PM
DIAL MODE
T
• If the battery pack becomes weak
during a call, the handset beeps ev-
ery 30 seconds, and RECHARGE
1. Set
to (tone).
NOWand
flash on the display. If
this happens, you must recharge the
battery pack before you can make
another call.
TALK
2. Press
tone.
and listen for a dial
• About once a month, fully discharge
the battery by keeping the handset
off the base until RECHARGE NOW
and
flash on the display. Other-
wise, the battery pack loses its abili-
ty to fully recharge.
• If you are not going to use your
phone for an extended period of
time, disconnect the battery pack.
This increases the battery pack’s
usable life.
0
3. Press any number other than .
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not dial the access code
either.
• The supplied battery pack should
last for about a year. When it loses
its ability to fully recharge, order a
replacement battery pack from your
local RadioShack store (see “Re-
placing the Battery Pack” on
Page 26).
If the dial tone stops, you have
DIAL
touch-tone service. Leave
MODE
T
set to .
If the dial tone continues, you have
DIAL MODE
P
pulse service. Set
(pulse).
to
SETTING THE DIALING
MODE
TALK
4. Press
or place the handset on
the base to hang up.
DIAL MODE
Set
on the back of the base
for the type of service you have. If you
are not sure which type you have, after
you charge the handset battery pack, do
this simple test.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 12 Tuesday, August 17, 1999 4:19 PM
Follow these steps to turn auto talk on or
off.
SETTING THE RINGER’S
TONE AND VOLUME
talk
1. Lift the handset. If
appears,
TALK
to turn it off.
Follow these steps to set the handset
ringer’s tone and volume.
press
FUNCTION
2. Press
4 times. The cur-
talk
1. Lift the handset. If
appears,
rent autotalk setting and ON-
1OFF-0appear.
TALK
press
to turn it off.
VOLUME
2. Press
. The phone dis-
plays and sounds the current ringer
tone and volume.
1
3. Press to turn on the autotalk fea-
0
ture, or to turn it off.
Note: To exit the autotalk display
without changing the setting, press
VOLUME
3. Repeatedly press
hear the desired ringer tone and vol-
VOLUME
until you
CANCEL
.
ume. Each time you press
,
the ringer setting changes in the fol-
lowing order:
Ring Type A High
Ring Type A Low
Ring Type B High
Ring Type B Low
MEM
4. Press
to store the new setting.
The handset beeps and briefly dis-
plays the new setting.
TURNING AUTOTALK
ON/OFF
Your phone is preset so you must press
TALK
when you lift the handset from the
base to answer a call. With auto talk
turned on, you can answer a call by just
lifting the handset from the base.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 13 Tuesday, August 17, 1999 4:19 PM
To delete an area code, follow Steps 1
MEM
a new area code. DELETINGappears.
STORING YOUR AREA
CODE
and 2, then press
without entering
To quickly dial a number from a Caller
ID record (see “Dialing from a Caller ID
Record” on Page 21) or to correctly
store a number from a record into a
memory dialing location (see “Storing a
Caller ID Record to Memory” on
Page 22), you must store your local area
code in the ET-929’s memory. Then,
when you dial from a Caller ID record,
the ET-929 skips the area code if it
matches the one you stored.
SETTING CALLER ID WITH
CALL WAITING
If you subscribe to Caller ID with Call
Waiting, you can set the ET-929 to show
Caller ID information for an incoming call
even while you are already on the
phone.
Follow these steps to turn Caller ID with
Call Waiting on or off.
Follow these steps to store your area
code.
talk
1. Lift the handset. If
appears,
talk
TALK
1. Lift the handset. If
appears,
press
to turn it off.
TALK
press
to turn it off.
FUNCTION
2. Press
three times.
FUNCTION
and 1-appear.
2. Press
twice. AREACODE
CIDCW (Caller ID Call Waiting), the
current setting, and ON-1 OFF-0
appear.
Note: If an area code is already
1
0
stored, it appears after the 1–.
3. Press to turn this feature on, or
DELETE
Press
three times to erase
to turn it off.
it.
MEM
4. Press
. The handset beeps and
briefly displays the new setting.
5. Return the handset to the base to
store the new setting.
3. Enter your 3-digit area code, then
MEM
press
. The handset beeps and
STORINGbriefly appears.
4. Return the handset to the base to
store the new area code.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 14 Tuesday, August 17, 1999 4:19 PM
OPERATION
MAKING CALLS
ANSWERING CALLS
1. Lift the handset and press TALK so CALLING appears on the handset
talk
appears.
when a call comes in. If you subscribe to
Caller ID service, the Caller ID informa-
tion appears by the second ring (see
“Caller ID Operation” on Page 20).
To answer the call, lift the handset and
press TALK. Or, if auto talk is on, just lift
talk
the handset from the base.
ap-
pears, and the display briefly shows the
channel number, then the call’s elapsed
time.
The IN USE indicator on the base
lights and the currently selected
channel number appears.
2. Dial the number. You see the num-
ber as you dial, then (after 5 sec-
onds) the elapsed time for this call.
To end a call, place the handset on the
base or press TALK.
You can also dial the number when
SETTING THE HANDSET
VOLUME
talk
is not on the display. The number
appears as you dial. When you finish di-
aling, press TALK. (The phone does not
dial the number until you press TALK.)
The ET-929’s handset has two volume
settings, normal and high. To change
the volume during a call, press VOLUME.
VOLNORMALor VOLHIGHappears.
Note: If you make a mistake dialing, re-
peatedly press DELETE to erase the er-
ror, then enter the correct number. To
erase the entire phone number, press
CANCEL.
The handset resets to normal volume af-
ter each call.
CHANGING THE
CHANNEL
The ET-929 has 40 channels (frequency
pairs used between the base and hand-
set). It automatically selects a clear
channel each time you make or receive
a call.
To end a call, place the handset on the
base or press TALK.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 15 Tuesday, August 17, 1999 4:19 PM
If you hear other conversations or ex-
cessive noise during a call, press CHAN-
NEL to select a different channel. The
new channel number briefly appears.
USING FLASH
FLASH performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
: If the handset is too far from the
Note
base, the channel might not change.
Move closer to the base and try again.
For example, if you have Call Waiting,
press FLASH to answer an incoming call
without disconnecting the current call.
Press FLASH again to return to the first
call.
USING REDIAL
If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
Note:
You can quickly dial the last number di-
aled. When you hear a dial tone, simply
press REDIAL.
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse dialing, you can still use these spe-
cial tone services by following these
steps.
Notes:
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
1. Be sure DIAL MODE is set to P
(pulse).
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 18.
2. Dial the service’s main number.
• The redial memory does not store a
flash entry or any digits you enter af-
ter you press FLASH (see “Using
Flash”).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 16 Tuesday, August 17, 1999 4:19 PM
3. When the service answers, press
TONE ( ). Any additional numbers
you dial are sent as tone signals.
To have the handset beep for 1 minute,
hold down PAGE/FIND for at least 2 sec-
onds. To stop the handset’s beeping,
press TALK twice.
MEMORY DIALING
You can store up to 20 phone numbers
and names in memory, then dial a stored
number by entering a two-digit memory
location number.
4. After you complete the call, return
the handset to the base or press
TALK. The phone automatically re-
sets to the pulse mode.
Each number can be up to 16 digits, and
each name can be up to 12 characters.
When you dial a number before
Note:
you press TALK, you can enter a tone
signal as part of the number (the display
shows ). When you press TALK, the
phone automatically adds a 1-second
pause after the tone entry, allowing time
for the service to answer (for example).
Storing a Number and Name in
Memory
:
Notes
• An error tone sounds and the phone
exits the storing process if you wait
more than 20 seconds between
each key press.
PAGING
To send a page from the base to the
handset, when the phone is not in use,
press PAGE/FIND on the base. The
handset beeps five times and PAGING
appears.
• If you receive a call during memory
entry, the phone exits the storing
process.
talk
1. Lift the handset. If
appears,
press TALK to turn it off.
2. Press FUNCTION. DIAL MEMORY?
and MEM-1EDIT-0appear.
3. Press 1 to store a new number.
PHONENO.?appears.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 17 Tuesday, August 17, 1999 4:19 PM
4. Enter the number and any tone and
pause entries (see “Using Tone Ser-
vices on a Pulse Line” on Page 15
Notes:
• Press s to see the characters in
reverse alphabetical order.
and “Entering
Page 18).
a
Pause” on
• You can hold down s or t to scroll
rapidly through the characters.
Note: Each tone or pause entry us-
es one digit of memory.
• If you make a mistake, move the
cursor over the error, then enter
the correct character, or press
MEM.
5. Press
NAME?appears. If you
do not want to put in a name, skip to
Step 7.
DELETE
to delete a character.
MEM
7. Press
. LOCATION?appears.
8. Enter the memory location number
(01–20) where you want to store the
number. The handset beeps and
STORINGbriefly appears.
For each stored number, write the per-
son’s or company’s name next to the ap-
propriate location number on the
supplied memory directory sticker. (Use
a pencil in case you need to change the
number later.) Peel the backing from the
sticker and attach it to the phone as
shown.
6. To enter a name, use t or s to select
the characters and
the cursor.
or
to move
Repeatedly press t to see the char-
acters in alphabetical order. (The
display shows uppercase letters
first, then lowercase letters, num-
bers, and special characters.)
To replace a stored number, simply store
a new one in its place.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 18 Tuesday, August 17, 1999 4:19 PM
Editing or Deleting a Memory
Number
Entering a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect.
talk
1. Lift the handset. If
press TALK to turn it off.
appears,
2. Press FUNCTION. DIAL MEMORY?
and MEM-1EDIT-0appear.
3. Press 0 to select EDIT. LOCA-
TION?appears.
4. Enter the memory location number
(01-20) for the number you want to
edit or delete. The display shows
the location number, name, and
phone number.
To enter a 2-second pause while storing
a phone number, press PAUSE. P ap-
pears. You can add more pause entries
for a longer pause.
Note: You can scroll through the
memory locations by pressing s or t.
5. To delete the selected number, hold
down DELETE until the handset
beeps and Nomemoryappears.
To edit the number, press MEM. Re-
peatedly press DELETE to delete
some or all of the number, then en-
ter the new number (in reverse or-
der) and press MEM again.
Dialing a Memory Number
1. Lift the handset and press TALK, so
talk
appears.
2. Press MEM and enter the memory
location number (01-20) for the
number you want to dial.
Note: To edit the name without edit-
ing the number, simply press MEM
twice.
To edit the name, use the s, t,
and keys as described in Step 6
of “Storing a Number and Name in
Memory” on Page 17.
,
You can also select a memory number
before you press TALK. Press MEM,
then enter the desired location number,
or use s and t to scroll through the mem-
ory locations. The display shows the lo-
cation number, name, and phone
number. Then press TALK.
6. Press MEM. STORING briefly ap-
pears.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 19 Tuesday, August 17, 1999 4:19 PM
Chain-Dialing Service Numbers
When calling special services (such as
alternate long distance or bank-by-
phone), dial the service’s main number
first. Then, at the appropriate place in
the call, press MEM and enter the num-
ber for the location where the additional
information is stored.
Testing Stored Emergency
Numbers
Notes:
• Connecting a headset disconnects
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
the handset’s earpiece and micro-
phone.
• VOLUME on the handset also con-
trols the connected headset’s vol-
ume.
• If you place the handset on the base
to recharge while the headset is
connected, be sure the handset
seats properly.
USING A HEADSET
With a headset connected, you can
make or answer calls as usual using the
keys on the handset.
You can talk on the phone with hands-free
convenience using an optional headset
that has a 3/32-inch (2.5-mm) plug. Contact
your local RadioShack store for a suit-
able headset.
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for greater
convenience.
To connect the headset, pull open the
rubber cover marked
on the side of
the handset, then insert the headset’s
plug into the jack.
When you finish using the headset, dis-
connect it from the handset and close the
rubber cover to protect the jack.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 20 Tuesday, August 17, 1999 4:19 PM
CALLER ID OPERATION
If you subscribe to Caller ID service, the
phone company sends information
about the call, as well as the time and
date, between the first and second rings
of every call you receive.
To scroll through the Caller ID records,
repeatedly press s or t.
call id
The ET-929 displays this information
when it receives a call, and it stores up
to 30 Caller ID records for later review. It
also shows if the name or number were
unavailable or blocked by the caller (see
“Caller ID Messages” on Page 21).
The first line of the record shows the
caller’s name, and the second line
shows the caller’s phone number. If the
name or number is longer than 12 char-
acters, the display shows the first 12
characters, then, after about four sec-
onds, the rest of the name or number
scrolls onto the display.
If you subscribe to Call Waiting with
Caller ID, you hear a tone through the
handset when a call comes in, then the
Caller ID record appears. To answer the
new call, press FLASH. To resume the
previous call, press FLASH again.
To see the date and time of a call, press
(8) while the Caller ID record is on the
display. The date, time, and record num-
ber appear. To return to the record,
press again.
If the phone’s Caller ID memory be-
comes full, any new call replaces the
oldest call record.
REVIEWING CALLER ID
RECORDS
To review Caller ID records, press CALL
ID. The display shows the total number
of records and the number of new
records, if any.
To see how many times a caller has
called, press TC (9) while the Caller ID
record is on the display. The name and
the total number of calls from that per-
son appear. To return to the record,
press TC again.
call id
Note: When
is blinking, the ET-
929 is busy. Wait for the blinking to stop
before you press a button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 21 Tuesday, August 17, 1999 4:19 PM
Caller ID Messages
DIALING FROM A CALLER
ID RECORD
Display
Description
To dial a local number stored in a Caller
ID record, recall the record, then press
TALK. To dial a long distance number,
recall the record and press 1 (1appears
before the displayed number), then
press TALK.
TOTALCALLS Appears when there
are no new Caller
ID records (ones
you have not re-
viewed).
xx
NEW TOTAL NEWis the number
of new Caller ID
records. TOTALis
the total of all Caller
ID records.
xx
xx
Appears when the
Caller ID informa-
tion was garbled, or
if there was an error
during the transmis-
sion.
Error
Notes:
• If a Caller ID record does not con-
tain a phone number (if it was
blocked by the caller, for example)
you cannot dial from that record.
Appears if the call-
er chose to block
sending Caller ID
information. Either
the name, the num-
ber, or both were
blocked.
UNAVAILABLE
OUT-OF-AREA
END
• If the stored number is longer than
16 digits, the phone sounds five
quick beeps when you press 1 and
does not dial it.
Appears if the call-
er is not within a
Caller ID service ar-
ea, or during opera-
tor-assisted calls or
calls made with a
credit card.
Appears when you
scroll before the first
or after the last Call-
er ID record.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 22 Tuesday, August 17, 1999 4:19 PM
STORING A CALLER ID
RECORD TO MEMORY
To store the name and number in a Call-
er ID record into the phone’s memory,
MEM
recall that record, then press
. LO-
CATION? appears. Enter a two-digit
memory location number (01–20), then
MEM
press
again. STORING briefly ap-
pears.
DELETING CALLER ID
RECORDS
You can delete Caller ID records individ-
ually, or all at once.
To delete a single record, recall the
DELETE
record, then hold down
least 2 seconds.
for at
CALLER
To delete all call records, press
ID
to display the total number of records,
DELETE
then hold down
until the hand-
set beeps and END appears (about 5
seconds).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 23 Tuesday, August 17, 1999 4:19 PM
TROUBLESHOOTING
We do not expect you to have any problems with your ET-929, but if you do, these
suggestions might help.
Problem
Suggestion
The phone does not work or
works poorly.
Be sure the base’s phone line cord and AC
adapter are correctly and securely connected.
Be sure the battery pack in the handset is con-
nected and charged.
Return the handset to the base for 5 seconds
to reset the security access-protection code.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical posi-
tion.
Be sure the handset’s battery pack is charged.
(If the battery pack power is too low, it does not
have enough power to light
on the display.)
Low volume or unusual
sounds.
Someone has picked up another phone on the
same line. Hang up the other phone.
Severe noise interference.
Keep the handset away from computers,
remote control toys, wireless microphones,
alarm systems, intercoms, room monitors, fluo-
rescent lights, and electrical appliances.
Move to another location or turn off the source
of interference.
Press CHANNEL to change the channel.
Hang up and redial the number.
The phone cannot be oper-
ated at a useful distance from
the base because the signal
becomes weak or noisy
(handset’s range has
Lift the base’s antenna to a vertical position.
Be sure neither the handset’s nor base’s
antenna is touching a metal surface.
Return the handset to the base and recharge
the battery pack.
decreased).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 24 Tuesday, August 17, 1999 4:19 PM
Problem
Suggestion
The handset battery pack
does not charge.
Check the charging contacts on the handset
and base. If they are dirty, clean them with a
pencil eraser.
Be sure the battery pack is connected cor-
rectly.
Replace the battery pack (see “Replacing the
Battery Pack” on Page 26).
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift base’s antenna to a vertical position.
Be sure the battery pack in the handset is con-
nected and charged.
Move the base away from other electrical
devices and sources of noise.
You hear an error tone (five
short beeps) when you press
TALK.
Check that the AC adapter is securely con-
nected.
Return the handset to the base for 5 seconds
to reset the security access-protection code.
If you still have problems, disconnect the ET-929. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take the ET-929 to your local RadioShack store for assistance.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 25 Tuesday, August 17, 1999 4:19 PM
CARE AND MAINTENANCE
Your RadioShack ET-929 900 MHz Cordless Telephone is an example of superior
design and craftsmanship. The following suggestions will help you care for your cord-
less telephone so you can enjoy it for years.
Keep the ET-929 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the ET-929 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age battery packs, and distort or melt plastic parts.
Keep the ET-929 away from dust and dirt, which can cause premature
wear of parts.
Handle the ET-929 gently and carefully. Dropping it can damage circuit
boards and cases and can cause the ET-929 to work improperly.
Use only a battery pack of the required size and recommended type.
Batteries can leak chemicals that damage your ET-929’s electronic
parts.
Wipe the ET-929 with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong detergents to
clean the ET-929.
Modifying or tampering with the ET-929’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it. If
your ET-929 is not performing as it should, take it to your local RadioShack store for
assistance. If the trouble is affecting the telephone lines, the phone company can ask
you to disconnect your ET-929 until you have resolved the problem.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 26 Tuesday, August 17, 1999 4:19 PM
REPLACING THE
BATTERY PACK
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 9, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
4. Replace the cover.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in
a fire because it might explode.
Install the new battery pack as de-
scribed below, then charge it for about
14 hours.
• Do not open or mutilate the battery
pack.
Note: To avoid losing phone numbers
stored in memory, try to install and begin
charging the new battery pack within 3
minutes.
• Be careful not to short the battery
pack by touching it with conducting
materials, such as rings, bracelets,
and keys. The battery pack or con-
ductor might overheat and burn.
1. Press down and slide off the battery
pack compartment cover as shown.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important: This product contains a re-
chargeable nickel cadmium battery. At
the end of the battery pack’s useful life,
it must be recycled or disposed of prop-
erly. Contact your local, county, or state
hazardous waste management authori-
ties for information on recycling or dis-
posal programs in your area. Some
options that might be available are: mu-
nicipal curb-side collection, drop-off box-
es at retailers such as your local
RadioShack store, recycling collection
centers, and mail-back programs.
2. Unfasten the plastic retainer strap
and lift the battery pack out of the
compartment, then gently pull on the
battery connector to disconnect it.
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment, place the battery pack into
the compartment, and refasten the
retainer strap.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 27 Tuesday, August 17, 1999 4:19 PM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Some cordless phones operate at fre-
quencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
LIGHTNING
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in phone line and power line
current. This lightning protection meets
or exceeds FCC requirements. Howev-
er, lightning striking the telephone or
power lines can damage your phone.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
you unplug your phone during storms to
reduce the possibility of damage.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it.
Try to eliminate the interference by:
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1099.fm Page 28 Tuesday, August 17, 1999 4:19 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
UCZZ01201ZZ
8A8N
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|