3. Use the codes in the accompanying code list to locate the
brand name and enter the first four-digit code for your
combo device (for example, TV/VCR). If you perform this
procedure correctly, the DVD/VCR key will blink twice.
NOTE: If a code digit is 0, the selected mode key will
not blink.
4. Repeat step 3 three more times for the remaining digits.
Use 2 for the second digit, 3 for the third digit, and 4 for
the fourth digit. Finish writing down the code in the TV
Code boxes.
Navigation keys move the cursor in the program guide and
Programming Device Control
Before you can start using this remote, you must program it
to control your components.
Cable Replacement Remote
RCRP05B Universal Remote Control
Owner’s Manual
menu screens and navigate within the interactive service.
OK chooses options, PPV events, and tunes to programs
from the program guide.
NOTE: If the DVD/VCR key did not blink twice after
entering the codes last digit, repeat steps 2 and 3 and
try entering the same code again. If you’ve located
a setup code that works for your combo device (for
example, a TV/VCR Combo) and a separate TV code
is also listed, you’ll need to program this code into
the remote control to access volume control (see the
“Programming Device Control” section).
GUIDE displays the program guide.
NOTES:
EXIT leaves (or clears) your device’s menu or guide.
The RCRP05B Cable Replacement Remote is preprogrammed
to operate an RCA TV, a Toshiba DVD player, an RCA VCR,
a Pioneer audio receiver, and a Motorola cable box. If you
own these brands of these devices, test the remote with
them. If they work, you do not have to program the remote
to operate them.
Manual del Propietario (parte posterior)
5. To check for other device codes, repeat steps 1 through 4,
but substitute the appropriate key (e.g., DVD/VCR, DVR/
AUX, AUD, or CBL/SAT) for the device you are checking.
Write down the codes in the appropriate boxes in the
“Programming Device Control” section.
DAY +/- moves a day forward (or back) on your device’s
program guide.
PAGE +/- moves up or down one screen at a time through
menu screens and the program guide.
Features and Functions
Introduction
Use the illustration below to locate features on the
RCRP05B Cable Replacement Remote and then study the
key descriptions below to learn how they function.
A,B,C,D (red, green, yellow, blue) access additional
features on your cable box, satellite receiver, or Blu-ray disc
player (see your device manual for details).
The RCRP05B Cable Replacement Remote by RCA is our
latest generation universal remote control. Its sophisticated
technology allows you to consolidate up to five of your
original home entertainment remote controls into one
easy-to-use product. Moreover, its packed with advanced
features such as:
4. Aim the remote control at your combo device (for
example, TV/VCR Combo) and press POWER once. The
device should turn off. If it does not respond, repeat
steps 2 and 3, trying each code listed for your brand until
you find one that works. If it still does not respond, try
searching for the code (see the “Searching for Your Code”
section).
For control of a Combo device (for example, a TV/VCR
combo), skip this section and perform the instructions
in the “Setting Up a Combo Unit” section. Also refer
to the “Device Table” to find out which devices can be
programmed onto each device key.
Using Learning
The RCRP05B Cable Replacement Remote includes a
Learning feature so you can add functions that are unique
to your home entertainment devices (e.g., VCR tracking up
or down).
VOL +/- raises (or lowers) the audio volume.
To find out what type of devices can be controlled by each
device key after programming, see the “Device Table”
section.
ON DEMAND accesses your program provider’s Video on
Demand services. The ON DEMAND key may not work with
your program provider. Test the key, and if it doesn’t take
you to your program provider’s On Demand service, you can
program the ON DEMAND key to access the service. See the
“Programming Macro Keys” section later in this manual for
more information.
1. Turn on a device and, if applicable, insert video media,
•
Dedicated keys to control popular functions on your
DVR/PVR (Digital/Personal Video Recorder)
TV, DVR/AUX, CBL/SAT,
DVD/VCR, and AUD select
a home entertainment
device to control. Also see
the “Device Table” section.
Each device key has an
embedded LED (red light)
that blinks upon selection
and indicates the remote
control is working and (after
programming) is sending
signals.
(e.g., cassette or disc).
5. For future reference, write down each working device
code in the boxes below:
Learning Precautions
NOTE: Please read steps 2 through 5 completely before
proceeding. Highlight or write down the codes and
device you wish to program before moving on to step 2.
•
•
•
•
•
Your original remote controls must be in working order
for learning to work properly.
Learned keys are mode-specific, so each one can store a
unique function for each mode.
Do not use the following keys for learning: device keys,
SETUP, (Record), Macro keys.
Learning capacity is up to a total of 50 keys, depending
on the code being learned.
Certain device functions are not learnable including
multi-frequency types, some high frequency ones, and
other unusual formats.
For optimum learning, avoid high levels of ambient light
such as natural sunlight or energy-efficient fluorescent
lights.
•
Programmable MASTER POWER key for master on/off
control of your home entertainment equipment with a
single keypress
TV/VCR or TV/DVD Code:
TV Code (if used):
CH+/- selects the next higher (or lower) channel. For DVD
players, use these keys to skip forward (or reverse) through
chapters. For amplifiers/receivers, use these keys to select
the next higher (or lower) preset station.
2. On the remote control, press a device key once (i.e., DVD/
VCR, DVR/AUX, AUD, TV, or CBL/SAT); it will blink once.
•
•
•
•
•
•
Programmable Macro Keys to consolidate multi-step
actions into a single keypress
Searching For Your Code
3. Press and hold SETUP until the selected mode key blinks
twice, then release SETUP.
Channel Lock to lock channel selection only to the cable
If your home entertainment device does not respond to the
RCRP05B Cable Replacement Remote after trying all of the
codes listed for your brand, or if your brand is not listed at
all, try searching for your code.
For example, to search for a code for your TV:
1. Turn on your TV.
2. On the remote control, press TV once; it will blink once.
Then press and hold SETUP until the TV key blinks twice.
3. Enter 9 9 1. The TV key will blink twice.
box or satellite receiver
NOTE: By default, the CH+/- keys change channels on
the CBL/SAT device regardless of what mode you’re
in. To change the way the CH+/- keys work, see the
“Programming Channel Control Lock” section.
4. Use the codes in the accompanying code list to locate
the type of device and brand name and then enter
the first four-digit code for your device. If performed
correctly, the selected mode key will blink twice.
Volume Lock to lock volume controls to one mode or
individual modes
NOTE: If you have a digital
TV converter, you can
program it to the CBL/SAT or
DVR/AUX keys.
Code Search to help program control of older or
•
discontinued components
MUTE turns the sound off or on.
NOTE: If the selected mode key emits a long blink,
the entry is invalid. Repeat steps 2 through 4 and try
entering the same code again.
Color-coded keys to quickly locate popular functions for
FAV cycles through your favorite channels on your cable
box or satellite receiver.
cable and satellite
NOTE: Please have your original remote controls handy
before programming learning.
POWER/MASTER POWER
turns on or off a home
entertainment device. For
MASTER POWER control, see
the “Using the Master Power
Key” section.
Code library for popular video and audio devices
LAST recalls the last channel.
5. Aim the remote control at the device and press POWER
once. The device should turn off. If it does not, repeat
steps 2 through 4, trying each code for your brand until
you find one that works. If it still does not respond,
try searching for the code (see the “Searching for Your
Code” section).
Before using the product, you will need to install batteries
and also perform some programming to operate the
specific home entertainment devices you wish to control.
Number keys (1-9, and 0) tune directly to channels (e.g.,
09). For amplifiers/receivers, use the keypad numbers to
select inputs 1 through 10.
4. Aim the remote control at the TV and press POWER once.
5. Press and release the CH+ key continuously, then stop
Programming a Learned Key
NOTE: If more than 15 seconds pass between key
presses, the remote exits programming.
when the TV turns off.
– accesses digital sub-channels (for example, 8.1 or 8.2).
NOTE: In the search mode, the remote control will send
IR codes from its library to the selected device, starting
with the most popular code first.
1. Press and hold SETUP until the last-selected mode key
blinks twice, then press 9 7 5.
ASPECT changes the aspect ratio of the show you are
watching. (Not available on all devices).
SETUP is used in all
programming sequences.
NOTE: If the device does not have a POWER key (e.g.,
DVD and VCR), press the
(Play) key.
6. Press POWER. The TV should turn on, then press SETUP
once to lock in the code. The LED will blink twice to
indicate that the code is saved.
NOTE: If the LED displays one long flash instead,
either your batteries are low, or the RCRP05B Cable
Replacement Remote has a memory fault.
Installing Batteries
1. On the back of the remote control, push the tab and lift
PIP turns the Picture-In-Picture feature on or off (if
available on your device).
LIVE commands your PVR/
DVR to return to watching
live TV.
6. Once you’ve found a code that turns your device on and
off, test other remote commands for that device (e.g.,
volume, channel, menu, etc.).
SWAP switches PIP images and sound between the main
and window pictures.
off the battery cover.
NOTE: If the TV does not turn on during step 6, then
slowly press and release CH- to go back through the
codes, then press SETUP when the TV turns on.
2. Press a mode key once (i.e., DVD/VCR, DVR/AUX, AUD,
TV, or CBL/SAT) to assign a mode for learning.
LIST displays a list of
recorded shows on your PVR/
DVR.
NOTE: By default, the CH+/- keys change channels on
the CBL/SAT device regardless of what mode you’re in.
So, you should only use these keys to test for CBL/SAT
device codes at this point.
MOVE moves the PIP window to different positions on your
TV screen.
3. Press the desired key on the RCRP05B once to store the
feature to be learned.
7. Test other remote commands for the TV (e.g., volume,
menu, etc.). If the commands you want to use with your
TV work, you’ve finished programming for your TV. If
they don’t, repeat steps 1-4 above. In step 5, don’t stop
when your TV turns off the first time—keep pressing
CH+ until it turns off again.
PIP CH +/- are used to select the next higher or lower
channel and is displayed on your PIP window.
(replay) commands your
PVR/DVR set-top box to
instantly replay the last 7
seconds of a program you
are watching.
4. Place the RCRP05B Remote Control head-to-head (about
2” apart) from your original remote control. Also locate
the key (on your original remote control) that you want
the RCRP05B Cable Replacement Remote to learn.
7. Repeat steps 1 through 6 for each device you want the
remote control to operate. For future reference, write
down each working device code in the boxes below.
2. Insert two (2) AA batteries (not included). Match the +
and - marks with those in the battery case, then insert
them.
INPUT in CBL/SAT mode is used to view other video sources
(A or B). In other modes, use INPUT to switch between the
source inputs on the device you are controlling.
NOTE: By default, the CH+/- keys change channels on
the CBL/SAT device regardless of what mode you’re in.
So, you should only use these keys to test for CBL/SAT
device codes at this point.
3. Align the covers keys with the cases holes and press the
cover back into place. The tab should click when the
cover is locked.
MACRO1 and MACRO2 are reserved for use as macro keys
(skip
forward, reverse, play,
forward, stop, pause,
record) In all modes
except CBL/SAT, use these
keys to control a VCR, DVD
player, or a PVR (after
selecting a desired device).
To record in DVD/VCR
mode, press twice. In CBL/
SAT mode, use these keys
to control the DVR/PVR
functions of the cable box or
satellite receiver.
DVD/VCR Code:
DVR/AUX Code:
AUD Code:
(see the “Programming Macro Keys” section).
4. Test the remote control by pressing any mode key (e.g.,
TV). If the batteries are inserted correctly, the LED (red
light) will blink once.
Device Table
NOTE: Please refer to the table below when performing
the instructions in the “Programming Device Control” or
“Setting Up a Combo Unit” sections.
2"
8. To search for the codes of your other devices, repeat steps
1 through 7, but substitute the appropriate key (e.g.,
DVD/VCR, DVR/AUX, AUD, or CBL/SAT) for the device
you’re searching for.
CBL/SAT Code:
TV Code:
NOTE: When batteries need replacement, the remote
control will cease to operate. Replace the batteries
and the unit will be restored to its full functionality,
complete with your favorite settings.
After programming, the RCRP05B Cable Replacement Remote
will be able to control the following types of devices:
5. On the original remote, press and hold the key to be
learned. The device key’s LED will blink rapidly, then turn
off. Continue holding the key on the original remote
until the device key LED blinks twice.
Checking the Codes
If you have set up your remote control by searching for your
device code, you may need to find out which four-digit code
is operating your equipment.
For example, to find out which code is operating your TV:
1. On the remote control, press TV once; it will blink once.
Then press and hold SETUP until the TV key blinks twice.
Setting Up a Combo Unit
If you own a combo unit such as a TV/VCR Combo or a TV/
DVD Combo, you need to follow special steps to set it up.
Perform the following instructions to control combo device:
Television
TV
Battery Precautions:
• Do not mix old and new batteries.
NOTE: If the LED displays one long blink, a learning
error has occurred. Try repeating this step again until
a successful capture occurs. If the function is still not
captured, press and hold SETUP to exit programming and
review the “Learning Precautions” earlier in this section. If
needed, also see “Troubleshooting” later in this manual.
After review, start programming again at step 1.
DVR, PVR, or auxiliary TV, DVD player, VCR,
or digital TV converter
DVR/AUX
1. For a TV/VCR Combo, turn on your TV/VCR Combo and
insert a video cassette. (For a TV/ DVD Combo, insert a
DVD).
• Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly
and recycle or dispose of them in accordance with Local
and National Regulations.
MENU displays the active
device’s menu system.
Cable box, satellite receiver, or digital TV
converter
CBL/SAT
DVD/VCR
AUD
2. Enter 9 9 0. The TV key will blink twice.
INFO displays the current
channel and program
information.
2. On the remote control, press DVD/VCR once; it will blink
once. Then press and hold SETUP until the DVD/VCR key
blinks twice.
DVD player, VCR, TV/VCR combo, or TV/DVD
combo
3. To view the code for the first digit, press 1 once. Count
the number of times the TV key blinks (e.g., 3 blinks = 3)
and write down the number in the left-most TV Code box
in the “Programming Device Control” section.
Audio amplifier, tuner, or receiver
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Repeat steps 2 through 5 for another mode and/or key
or press and hold SETUP until the active mode key LED
blinks twice to exit programming.
DVR/AUX, TV, and CBL/SAT). This can be an advantage if, for
example, you always listen to home entertainment devices
through your receiver’s speakers.
This product is covered by one or more of the following U.S.
patents:
5,515,052, 6,014,092, 5,255,313, 5,414,761, 5,552,917,
6,097,309, 6,522,262, 5,568,367, 6,330,091, 6,701,091
Programming a Macro Key
1. On the remote control, press and hold the SETUP key
until it blinks twice.
2. Enter 9 9 5. The SETUP key blinks twice.
Re-Assigning Device Keys
The RCRP05B Cable Replacement Remote can be set up to
control a second device of an already-assigned type.
For example, to have the unit control a TV, a set-top box,
and two audio devices (for example, two audio receivers),
re-assign the unused DVD/VCR key to operate the second
audio device as follows:
NOTE: Performing the steps below will overwrite the
device you’ve programmed for the device key.
1. On the remote control, press DVD/VCR once; it will blink
once. Then press and hold SETUP until the DVD/VCR key
blinks twice.
Troubleshooting
Device key does not blink when you press a key.
Replace the batteries with two (2) new AA batteries (see
the “Installing Batteries” section).
Deleting a Single Learning Key
Unlocking Volume Control for a Single
Device (Individual Volume Unlock)
1. Assuming Global Volume Lock is active, select a mode on
the remote control that you want to unlock (e.g., CBL/
SAT) and press it once. Next, press and hold SETUP until
the device key blinks twice.
3. Select a macro key (for example, MACRO1) and press it
This process returns the key to its original programming
for the mode you select. You can also delete learned
programming by teaching a different function to the key
(see the “Programming a Learned Key” section)
NOTE: If more than 15 seconds pass between key
presses, the remote exits programming.
1. Press and hold SETUP until the last-selected mode key
blinks twice, then press 9 7 6.
2. Press a mode key once (i.e., DVD/VCR, DVR/AUX, AUD,
TV, or CBL/SAT). The LED on the selected mode key will
blink once.
once.
Device key blinks when you press a key, but home
entertainment device does not respond.
Make sure you are aiming the remote control at your home
entertainment device and that you are within 15 feet of the
device you are trying to control.
4. Press the key sequence you want to program into
the macro. For example, to turn on your TV and raise
its volume, press the TV mode key once, followed by
pressing the VOL+ key once.
Care and Maintenance
• Keep the remote dry. If it gets wet, wipe it dry
immediately.
2. Enter 9 9 3. The last-selected device key will blink twice.
3. Press VOL- once. The last-selected device key will blink
• Use and store the remote only in normal temperature
environments.
• Handle the remote gently and carefully. Don’t drop it.
• Keep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to
keep it looking new.
• Modifying or tampering with the remote’s internal
components can cause malfunction and invalidate its
warranty.
NOTE: You can program up to 15 key presses into one
macro.
5. Press and hold SETUP until it blinks twice.
The remote control does not control devices or
commands are not performing properly.
Try all listed codes for the device brand being set up. Make
sure all devices can be operated with an infrared remote
control.
four times.
2. Enter 9 9 2. The DVD/VCR key will blink twice.
3. Press AUD once, then press DVD/VCR once. The DVD/VCR
4. Repeat steps 1 through 3 for each device you want
volume to be unlocked.
6. To add another macro, repeat steps 1 through 5,
substituting the new key sequence to be added in step 4.
NOTE: Programming more than five macros on the
same macro key overwrites previous settings.
key will blink twice.
Now, after you select a device that has volume unlocked
(e.g., CBL/SAT), pressing VOL+, VOL-,or MUTE, will control
only that device’s volume.
3. Press the key containing the learned function to be
deleted twice. The active mode key will blink twice.
4. Repeat steps 2 through 3 for another key or press and
The DVD/VCR key is now ready to be programmed for
your second audio device. See the “Programming Device
Control” section. To re-assign other device keys, repeat
these and substitute the key sequence using the following
chart:
NOTE: Only one device can be assigned to an unused
device key at a time.
DVD/VCR as 2nd AUD key
TV/VCR Combo does not respond properly.
Use the VCR codes for your brand. Some combo units may
require both a TV code and a VCR code for full operation
(see the “Setting Up a Combo Unit” section).
Clearing a Macro Key
1. On the remote control, press and hold the SETUP key
until it blinks twice.
2. Enter 9 9 5. The SETUP key blinks twice.
3. Press once on the macro key you want to clear.
4. Press and hold SETUP until the active mode key blinks
hold SETUP to exit programming.
Unlocking All Volume Control (Global
Volume Unlock)
NOTE: Performing these instructions will set independent
volume control for all programmed devices.
Deleting All Learned Keys in a Specific Mode
Limited Lifetime Warranty
No volume on a second TV.
Follow instructions in the “Changing Volume Lock” section.
NOTE: If more than 15 seconds pass between key
presses, the remote exits programming.
1. Press and hold SETUP until the last-selected mode key
blinks twice, then press 9 7 6.
2. Press a mode key twice (i.e., DVD/VCR, DVR/AUX, AUD,
TV, or CBL/SAT) to clear all the learned keys for that
mode. The mode key LED blinks twice.
Audiovox Electronics Corporation (the “Company”) warrants
to you the original retail purchaser of this product that should
it, under normal use and conditions, be proven defective in
material or workmanship during its lifetime while you own it,
such defect(s) will be repaired or replaced (at the Company’s
option) without charge for parts and repair labor. To obtain
repair or replacement within the terms of this Warranty,
the product is to be delivered with proof of warranty
coverage (e.g. dated bill of sale), specification of defect(s),
transportation prepaid, to the Company at the address shown
below. Do not return this product to the retailer.
(Play) and (Stop) keys do not work on a
Motorola DCT-2000 cable converter.
Re-program the CBL/SAT key for cable code 0476 (see the
“Programming Device Control” section).
1. On the remote control, press and hold SETUP until the
DVD/VCR—>SETUP—>9—>9—>2—>AUD—>DVD/VCR
twice.
last-selected device key blinks twice.
DVD/VCR as 2nd TV key
DVD/VCR—>SETUP—>9—>9—>2—>TV—>DVD/VCR
This macro key is now clear and ready for reprogramming
(see “Programming a Macro Key” earlier in this section). If
desired, repeat these to clear another Macro key.
2. Enter 9 9 3. The last-selected device key will blink twice.
3. Press VOL+ once. The last-selected device key will blink
DVD/VCR as 2nd CBL/SAT key
DVD/VCR—>SETUP—>9–>9–>2–>CBL/SAT—>DVD/VCR
four times.
Tried Search Method and still could not find a
working code.
Try the Search Method again after clearing out the device
key as follows:
a. Press and hold SETUP until device key blinks twice.
b. Enter 9 9 2.
c. Press and release the device key to be cleared twice.
3. Repeat step 2 for another mode or press and hold SETUP
to exit programming.
Using The Master Power Key
The RCRP05B Remote Control has a unique feature that
allows you to sequentially turn on or off up to five of your
home entertainment devices with a single key press.
NOTE: MASTER POWER (POWER) only works in the CBL/SAT
mode. If it is not programmed, only the cable box or satellite
receiver will turn on or off. In any other mode, pressing
MASTER POWER (POWER) once will turn the selected device
on or off.
Locking Volume Control To One Mode
(Global Volume Lock)
DVD/VCR back to DVD/VCR
DVD/VCR—>SETUP–>9–>9–>2–>DVD/VCR—>DVD/VCR
Programming Channel Control Lock
This Warranty does not cover product purchased, serviced
or used outside the United States or Canada. This Warranty
is not transferable and does not extend to costs incurred for
installation, removal or reinstallation of the product. This
Warranty does not apply if in the Company’s opinion, the
product has been damaged through alteration, improper
installation, mishandling, misuse, neglect, accident, or the
simultaneous use of different battery types (e.g. alkaline,
standard or rechargeable).
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE
COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or
liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION
OF THIS WARRANTY. IN NO CASE SHALL THE COMPANY BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER. No person or representative is authorized to
assume for the Company any liability other than expressed
herein in connection with the sale of this product.
Some states/provinces do not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of
incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you
specific legal rights and you may also have other rights, which
vary from state/province to state/province.
NOTE: The audio mode’s volume controls are active
regardless of Volume Lock settings. However, if you lock
the volume controls to the AUD mode, you will control the
audio device’s volume in all other modes (i.e., DVD/VCR,
DVR/AUX, TV, or CBL/SAT). This can be an advantage if, for
example, you always listen to home entertainment devices
through your receiver’s speakers.
1. On the remote control, press and hold SETUP until the
last-selected device key blinks twice.
2. Enter 9 9 3. The last-selected device key will blink twice.
To re-assign another unused device key, substitute it for the
DVD/VCR key above and then perform the sequence. For
example, to re-assign an unused AUD key as a second DVD
key, perform:
By default, in TV mode the remote control’s channel-control
capabilities are locked to the cable box or satellite receiver.
The affected keys are 1 through 0, CH+, CH-, and LAST.
This will guarantee that you do not inadvertently change
a channel on your TV. However, you can deactivate this
feature to allow full access to these keys in TV mode.
Remote control does not turn on Sony or Sharp
TV/VCR Combo.
For power on, these products require programming TV
codes on the remote control. For Sony, use TV code 0000
and VCR code 0032. For Sharp, use TV code 0093 and VCR
code 0048.
AUD—>SETUP—>9—>9—>2—>DVD—>AUD.
When a re-assignment is done, the selected device key
(e.g., AUD) will blink twice to confirm your choice. At that
time, you will need to program device control (see the
“Programming Device Control” section).
Programming the Master Power Key
1. On the remote control, press and hold SETUP until the
last-selected device key blinks twice.
2. Enter 9 9 5. The last-selected device key blinks twice.
3. Press POWER once.
4. For the first device you want in the power on sequence,
press a device key (e.g., CBL/SAT) once. Then press
POWER once. For the second device in the power
sequence, press its key once (e.g, TV). Then press
POWER.
5. Repeat step 4 up to four more times to add the second,
third, fourth, and fifth device.
Unlocking Channel Control
1. On the remote control, press CBL/SAT once; it will blink
once. Press and hold SETUP until the CBL/SAT key blinks
twice.
2. Enter 9 7 3. The CBL/SAT key will blink twice.
3. Press CH- once. The CBL/SAT key will blink four times.
For more information, please visit
3. Select a mode (e.g., TV or AUD) which you want to use
to control the volume. The selected device key will blink
twice.
Clearing Custom Programming
The RCRP05B Remote Control contains a Custom
Programming Reset program. You can use it to remove
all custom programming, except your setup codes and
reassigned device keys.
Consumer Help Line: 1-800-420-7968
Now, when you press VOL+, VOL-,or MUTE, the volume
of the selected device (e.g., TV) is controlled regardless of
mode.
FCC Notice
Now the remote control will provide TV and VCR channel-
control capabilities while in the TV or VCR mode.
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
Locking Channel Control to CBL/SAT
1. On the remote control, press CBL/SAT once; it will blink
once. Press and hold SETUP until the CBL/SAT key blinks
twice.
2. Enter 9 7 3.The CBL/SAT key will blink twice.
3. Press CH+ once. The CBL/SAT key will blink twice.
IMPORTANT: Executing this program will erase all custom
settings for Volume Lock, learned keys, Macro keys, and
Channel Lock. However, your device programming remains.
Programming Macro Keys
6. To save the settings and exit the program:
a. Press CBL/SAT once.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been verified to comply with the limits for a class B
computing device, pursuant to FCC Rules. In order to maintain compliance
with FCC regulations, shielded cables must be used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to
result in interference to radio and TV reception. The user is cautioned that
changes and modifications made to the equipment without the approval
of manufacturer could void the user’s authority to operate this equipment.
The RCRP05B Cable Replacement Remote includes two
macro keys (located directly below the SWAP and MOVE
keys). Macro keys allow you to set up key macros to activate
certain keys in a specific order. For example, you can set up
a key macro to change the channels on your TV, raise or
lower the volume, and start recording on your VCR, all with
the touch of one key. If you want to change the macros
stored in a previously-programmed macro key, you’ll need
to clear the key first (see “Clearing a Macro Key” later in
this section).
1. On the remote control, press and hold SETUP until the
last-selected device key blinks twice.
b. Press and hold SETUP until the CBL/SAT key blinks twice.
2. Enter 9 8 0. The last-selected device key blinks twice,
pauses, and blinks twice again to confirm that all custom
programming is cleared.
Now, regardless of what mode you select (except AUD), the
channel keys will only change channels on your set-top box.
Using the Master Power Key
1. After programming, point the remote control at the
devices. Press CBL/SAT once.
2. Press POWER once to sequentially turn the programmed
home entertainment devices on or off.
You will see the devices turn on or off according to the
programmed sequence.
Changing Volume Lock
Volume Lock allows you to control the volume through the
device identified as having your primary speaker(s), regardless
of which mode you are using. On the RCRP05B Remote
Control, Global Volume Lock is set to TV, so you can control TV
volume while in the DVD/VCR, DVR/AUX, TV or CBL/SAT mode.
You can perform Individual Volume Unlock on a selected
device to set its volume control for independent operation.
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,
Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy
Road, Unit 3, Door 16, Mississauga, Ontario L5T 3A5
Clearing the Master Power Key
1. On the remote control, press and hold SETUP until the
last-selected device key blinks twice.
2. Enter 9 9 5. The last-selected device key blinks twice.
3. Press and release POWER.
4. Press and hold SETUP until the CBL/SAT key blinks twice.
NOTE: The audio mode’s (AUD) volume controls are active
regardless of Volume Lock settings. However, if you lock the
volume controls to the AUD mode, you will have control of
the audio device’s volume in all other modes (i.e., DVD/VCR,
©2009 Audiovox Accessories Corporation
Trademark(s) ® Registered
RCRP05B US IB 01
Download from Www.Somanuals.com. All Manuals Search And Download.
AVISO: Si el LED muestra un parpadeo continuo, ha
ocurrido un error de aprendizaje. Repita este paso hasta
lograr grabar la función. Si aún no se graba la función,
oprima y sostenga SETUP para abandonar el procedimiento
de programación, y revise la sección “Precauciones Relativas
a la Función de Aprendizaje”. Si es necesario, consulte
también la sección “Resolución de Problemas” de este
manual. Después de revisarla, reinicie el procedimiento de
programación desde el paso 1.
1. Oprima y sostenga SETUP en el control remoto hasta
que parpadee dos veces la tecla del último dispositivo
seleccionado.
4. Para el primer dispositivo de la secuencia de encendido,
oprima una tecla de dispositivo (p. ej., CBL/SAT) una vez.
Seguidamente, oprima POWER una vez. Para el segundo
dispositivo de la secuencia de encendido, oprima su tecla
correspondiente una vez (p. ej., TV). Seguidamente, oprima
POWER.
Una vez finalizada la reasignación, la tecla de dispositivo
seleccionada (p. ej., AUD) debe parpadear dos veces para
confirmar su elección. Entonces será necesario programar el
control del dispositivo (consulte la sección “Programación del
Control de Dispositivos”).
Cambio de Canal sólo a través del Aparato de
Cable o del Receptor de Satélite
1. Oprima una vez la tecla CBL/SAT del control remoto, la cual
deberá parpadear una vez. Oprima y sostenga SETUP hasta
que la tecla CBL/SAT parpadee dos veces.
Aviso de la FCC
Este equipo ha sido probado, y se consideró que cumple con los límites
de los aparatos digitales de clase B, de acuerdo con las especificaciones
de la parte 15 de las Reglas de la FCC. El objetivo de estos límites es
ofrecer una protección razonable contra interferencias nocivas en una
instalación residencial. Este equipo genera, utiliza y puede radiar energía de
radiofrecuencia y, si no se instala y utiliza de acuerdo con estas instrucciones,
puede generar interferencia perjudicial para las radiocomunicaciones.
Sin embargo, no se garantiza que no se producirá interferencia en una
instalación en particular. Si su equipo causa interferencia perjudicial
para la recepción de radio o televisión, que puede averiguar apagando y
encendiendo el equipo, intente corregirla mediante uno o varios de los
siguientes procedimientos:
2. Ingrese 9 9 3. La tecla correspondiente al último dispositivo
seleccionado deberá parpadear dos veces.
3. Seleccione el modo (p. ej., TV o AUD) que le interese
usar para regular el volumen. La tecla del dispositivo
seleccionado deberá parpadear dos veces.
5. Repita el cuarto paso hasta cuatro veces más para incorporar
2. Ingrese 9 7 3. La tecla CBL/SAT deberá parpadear dos veces.
Eliminación de Programas Personales
el segundo, el tercero, el cuarto y el quinto dispositivo.
3. Oprima CH + una vez. La tecla CBL/SAT deberá parpadear
El Control Remoto modelo RCRP05B contiene un programa
de eliminación de programas personales. Puede usarlo para
eliminar todos sus programas personales, excepto sus códigos de
configuración y las teclas de dispositivo que haya reasignado.
6. Para guardar la configuración y salir del programa:
dos veces.
Ahora, puede regularse el volumen del dispositivo seleccionado
(p. ej., el televisor) mediante las teclas VOL+, VOL- o MUTE sin
importar el modo.
6. Repita los pasos 2 al 5 para otro modo o tecla, y oprima
y sostenga SETUP hasta que el LED del modo activo
parpadee dos veces para abandonar el procedimiento de
programación.
a. Oprima CBL/SAT una vez.
Ahora, sin importar en qué modo se encuentre (excepto AUD),
podrá usar las teclas de canales para cambiar solamente el canal
del aparato.
b. Oprima y sostenga SETUP hasta que la tecla CBL/SAT
IMPORTANTE: Este programa elimina todas las configuraciones
personales de bloqueo de volumen, teclas con funciones
aprendidas, teclas de macro y bloqueo de canales. Sin embargo,
permanece la programación de todos los dispositivos.
• Vuelva a orientar o cambie de lugar la antena receptora.
• Aumente la separación entre el equipo y
el receptor.
• Conecte este equipo a un tomacorriente en un circuito diferente al que esté
conectado el receptor.
• Consulte al distribuidor o a un técnico experimentado de radio y televisión
para solicitar asistencia.
Este equipo ha sido verificado y se sabe que cumple con los límites para un
dispositivo de computación de clase B, de acuerdo con las especificaciones
de las Reglas de la FCC. Para garantizar el cumplimiento con las reglas de la
FCC, se deben utilizar cables blindados con este equipo. El funcionamiento
con equipo no aprobado o cables no blindados podría ocasionar interferencia
en la recepción de radio y TV. Se le advierte al usuario que los cambios y
modificaciones realizados al equipo sin la aprobación del fabricante podrían
anular la autoridad del usuario conferida para utilizar este equipo.
parpadee dos veces.
Programación de las Teclas Macro
Modificación del Bloqueo de Volumen
Uso de la Tecla Master Power
1. Una vez programado, apunte el control remoto a los
dispositivos. Oprima CBL/SAT una vez.
Eliminación de una Función Aprendida
El Control Remoto Sustituto modelo RCRP05B contiene dos
teclas macro (situadas directamente debajo de las teclas
SWAP y MOVE). Las teclas macro permiten programar macros
para accionar ciertas teclas en una secuencia específica. Por
ejemplo, puede programarse una macro para cambiar el canal
del televisor, subir o bajar el volumen y empezar a grabar en
la VCR, todo oprimiendo una sola tecla. Si le interesa cambiar
las macros grabadas anteriormente en una tecla macro, debe
borrar antes el programa de esa tecla (consulte “Eliminación de
la Programación de una Tecla Macro” en esta sección).
El bloqueo de volumen permite regular el volumen a través
del dispositivo que se haya identificado como portador de los
altavoces principales, sin importar el modo que esté usándose.
En el Control Remoto modelo RCRP05B, el Bloqueo General de
Volumen se ha programado para funcionar con el televisor, de
manera que pueda regularse el volumen del televisor en los
modos DVD/VCR, DVR/AUX, TV o CBL/SAT. Se puede desbloquear
el volumen de los dispositivos seleccionados si interesa regular
su volumen de forma independiente.
Este proceso permite restituir la programación original de una
tecla para el modo seleccionado. También puede eliminar una
función aprendida programando otra función en esa tecla
(consulte la sección “Programación de Teclas con Funciones
Aprendidas”).
1. Oprima y sostenga SETUP en el control remoto hasta
que parpadee dos veces la tecla del último dispositivo
seleccionado.
2. Oprima POWER una vez para encender o apagar
secuencialmente los dispositivos de entretenimiento en el
hogar programados.
2. Ingrese 9 8 0. La tecla del último dispositivo seleccionado
deberá parpadear dos veces, hacer una pausa y volver a
parpadear dos veces para confirmar que se ha borrado toda
la programación personal.
AVISO: Si tarda más de 15 segundos en oprimir una
tecla después de la otra, el control remoto abandona el
procedimiento de programación.
Verá encenderse o apagarse los dispositivos en la secuencia
programada.
Eliminación de la Programación
de la Tecla Master Power
1. Oprima y sostenga SETUP en el control remoto hasta
que parpadee dos veces la tecla del último dispositivo
seleccionado.
1. Oprima y sostenga SETUP hasta que parpadee dos veces la
tecla del último modo seleccionado y, después, oprima 9 7 6.
AVISO: Los controles de volumen del modo de audio (AUD)
están activos sin importar la configuración del bloqueo de
volumen. Sin embargo, si se programan los controles de
volumen para funcionar sólo en el modo AUD, se podrá regular
el volumen de los dispositivos de audio en todos los demás
modos (p. ej., DVD/VCR, DVR/AUX, TV y CBL/SAT). Esto puede
resultar ventajoso si, por ejemplo, uno siempre escucha sus
dispositivos de entretenimiento en el hogar a través de los
altavoces del receptor.
Resolución de Problemas
Este producto está cubierto por una o más de las siguientes
patentes: 5,515,052, 6,014,092, 5,255,313, 5,414,761, 5,552,917,
6,097,309, 6,522,262, 5,568,367, 6,330,091, 6,701,091
La tecla de dispositivo no parpadea cuando usted oprime
una tecla.
2. Oprima una vez una de las teclas de modo (p. ej., DVD/VCR,
DVR/AUX, AUD, TV o CBL/SAT). El LED correspondiente al
modo seleccionado deberá parpadear una vez.
Programación de las Teclas Macro
1. Oprima y sostenga SETUP en el control remoto hasta que
Sustituya las baterías por dos (2) baterías AA nuevas (consulte la
sección “Instalación de Baterías”).
parpadee dos veces.
Cuidado y Mantenimiento
• Mantenga el control remoto seco. Si se moja, séquelo inmediatamente.
• Utilice y almacene el control remoto únicamente en entornos de
temperatura normal.
• Maneje el control remoto de forma cuidadosa. No lo deje caer.
• Mantenga el control remoto resguardado del polvo y la suciedad.
• Limpie el control remoto con un paño húmedo de vez en cuando para
mantenerlo en buenas condiciones de operación.
• Modificar o sabotear los componentes internos del control remoto
podría ocasionar desperfectos y anular la garantía.
3. Para eliminar la función aprendida, oprima dos veces la tecla
correspondiente. La tecla correspondiente al modo activo
deberá parpadear dos veces.
2. Ingrese 9 9 5. La tecla correspondiente al último dispositivo
seleccionado deberá parpadear dos veces.
La tecla de dispositivo parpadea cuando usted oprime
una tecla, pero el dispositivo de entretenimiento no
responde.
Asegúrese de apuntar el control remoto al dispositivo
de entretenimiento en el hogar que pretende manejar y
compruebe que no haya más de 4,6 metros de separación entre
ellos.
2. Ingrese 9 9 5. La tecla SETUP deberá parpadear dos veces.
3. Seleccione una tecla macro (p. ej., MACRO1) y oprímala una
vez.
3. Oprima y suelte POWER.
4. Repita los pasos 2 y 3 con otra tecla u oprima y sostenga
4. Oprima y sostenga SETUP hasta que la tecla CBL/SAT
4. Oprima la secuencia de teclas que le interesa programar
en la macro. Por ejemplo, para encender el televisor y
subir el volumen, oprima una vez la tecla de modo TV y,
seguidamente, oprima una vez la tecla VOL+.
SETUP para abandonar el procedimiento de programación.
parpadee dos veces.
Desbloqueo del Control de Volumen de un
Dispositivo (Desbloqueo de Volumen Individual)
1. Suponiendo que está activo el bloqueo general de volumen,
seleccione en el control remoto el modo que le interesa
desbloquear (p. ej., CBL/SAT) y oprímalo una vez. Seguida-
mente, oprima y sostenga SETUP hasta que la tecla de
dispositivo parpadee dos veces.
Eliminación de Todas las Funciones
Aprendidas para un Modo Específico
Reasignación de las Teclas de Dispositivo
Control Remoto Sustituto para TV por Cable modelo RCRP05B
puede configurarse para manejar un segundo dispositivo de un
tipo ya asignado.
El control remoto no permite manejar los dispositivos o
los comandos no se cumplen correctamente.
Pruebe con todos los códigos de la lista que correspondan a la
marca del dispositivo que se configura. Verifique que todos los
dispositivos puedan manejarse mediante un control remoto de
infrarrojos.
AVISO: En una macro se puede programar secuencias de
hasta 15 teclas.
AVISO: Si tarda más de 15 segundos en oprimir una
tecla después de la otra, el control remoto abandona el
procedimiento de programación.
Garantía Limitada Durante
la Vida Útil del Producto
5. Oprima y sostenga SETUP hasta que parpadee dos veces.
6. Para añadir otra macro, repita los pasos 1 al 5 usando en el
Por ejemplo, para manejar con la unidad un televisor, un
aparato y dos dispositivos de audio (p. ej., dos receptores de
audio), reasigne la tecla ociosa DVD/VCR al segundo dispositivo
de audio siguiendo este procedimiento:
Audiovox Electronics Corporation (la “Compañía”) le garantiza a usted,
el comprador original de este producto que si, bajo condiciones y uso
normales, se encontrara que presenta defectos materiales o de mano de
obra durante su vida útil mientras sea de su propiedad, tales defectos
serán reparados o reemplazados (a opción de la Compañía) sin cargo
alguno por las piezas y labores de reparación. Para obtener los servicios
de reparación o reemplazo dentro de los términos de esta Garantía, el
producto se entregará con prueba de cubierta de garantía (por ejemplo,
factura fechada de venta), especificación de los defectos, transporte
prepagado, a la Compañía a la dirección indicada abajo. No devuelva este
producto al distribuidor.
2. Ingrese 9 9 3. La tecla correspondiente al último dispositivo
seleccionado deberá parpadear dos veces.
cuarto paso la nueva secuencia de teclas que interesa.
1. Oprima y sostenga SETUP hasta que parpadee dos veces la
tecla del último modo seleccionado y, después, oprima 9 7 6.
La combinación de TV/VCR no responde correctamente.
Use los códigos de VCR correspondientes a su marca. Para
poder manejar plenamente algunas unidades de combinación
es necesario usar tanto el código de TV como el código de
VCR (consulte la sección “Configuración de Unidades de
Combinación”).
AVISO: Programar más de cinco macros en la misma tecla
macro anula la configuración anterior.
3. Oprima VOL- una vez. La tecla del último dispositivo
seleccionado deberá parpadear cuatro veces.
2. Oprima dos veces una de las teclas de modo (p. ej., DVD/
VCR, DVR/AUX, AUD, TV o CBL/SAT) para borrar todas las
funciones aprendidas para ese modo. El LED de la tecla de
modo parpadea dos veces.
AVISO: Este procedimiento anulará la programación que se
haya hecho de la tecla de dispositivo.
4. Repita los pasos 1 al 3 para cada dispositivo cuyo volumen le
interese desbloquear.
Eliminación de la Programación de una Tecla Macro
1. Oprima y sostenga SETUP en el control remoto hasta que
1. Oprima una vez la tecla DVD/VCR del control remoto, la
cual deberá parpadear una vez. Seguidamente, oprima y
sostenga SETUP hasta que la tecla DVD/VCR parpadee dos
veces.
El segundo televisor no tiene volumen.
Siga las instrucciones de la sección “Modificación del Bloqueo
de Volumen”.
3. Repita el paso 2 para otro modo u oprima y sostenga SETUP
Ahora, una vez seleccionado el dispositivo con volumen
bloqueado (p. ej., CBL/SAT), cuando se oprima VOL+, VOL- y
MUTE, sólo se regulará el volumen de ese dispositivo.
parpadee dos veces.
para abandonar el procedimiento de programación.
2. Ingrese 9 9 5. La tecla SETUP deberá parpadear dos veces.
3. Oprima una vez la tecla macro que le interesa borrar.
Esta Garantía no cubre un producto adquirido, mantenido o utilizado
fuera de los Estados Unidos o Canadá. Esta Garantía no es transferible y
no incluye los costos incurridos en la instalación, remoción o reinstalación
de este producto. Esta Garantía no aplica si, es opinión de la Compañía
que, este producto ha sufrido daños debido a alteraciones, instalación
inadecuada, abuso, uso indebido, negligencia, accidente o el uso
simultáneo de diferentes tipos de baterías (por ejemplo, alcalinas,
típicas o recargables). EL ALCANCE DE LA RESPONSABILIDAD DE LA
COMPAÑÍA BAJO ESTA GARANTÍA ESTÁ LIMITADO A LA REPARACIÓN
O EL REEMPLAZO PROVISTO ARRIBA Y, EN NINGÚN CASO, DEBERÁ LA
RESPONSABILIDAD DE LA COMPAÑÍA EXCEDER EL PRECIO DE COMPRA
PAGADO POR EL COMPRADOR DE ESTE PRODUCTO.
Las teclas
y
no funcionan con
2. Ingrese 9 9 2. La tecla DVD/VCR deberá parpadear dos veces.
Programación del Bloqueo
de Control de Canales
De forma predeterminada para el modo TV, el control remoto
sólo permite cambiar el canal del aparato de cable o del
receptor de satélite. Las teclas relacionadas con esta restricción
son las teclas numéricas del 0 al 9, CH+, CH- y LAST. Con ello
se impide cambiar accidentalmente el canal del televisor. No
obstante, puede desactivarse esta característica para dar acceso
pleno a estas teclas en el modo TV.
un aparato de cable Motorola DCT-2000.
Vuelva a programar la tecla CBL/SAT con el código de cable 0476
(consulte la sección “Programación del Control de Dispositivos”).
Desbloqueo del Control de Volumen de Todos los
Dispositivos (Bloqueo General de Volumen)
AVISO: Estas instrucciones permiten independizar el control de
volumen de todos los dispositivos programados.
4. Oprima y sostenga SETUP hasta que la
3. Oprima AUD una vez y, seguidamente, DVD/VCR una vez. La
tecla DVD/VCR deberá parpadear dos veces.
tecla del modo activo parpadee dos veces.
Ahora esta tecla macro está vacía y puede reprogramarse
(consulte “Programación de las Teclas Macro” en esta sección).
Si le interesa, repita este procedimiento para borrar la
programación de otra tecla macro.
Ahora la tecla DVD/VCR se puede programar para un segundo
dispositivo de audio. Consulte la sección “Programación
del Control de Dispositivos”. Para reasignar otras teclas
de dispositivo, repita este procedimiento usando la
correspondiente secuencia de teclas que se indica en este
diagrama:
He seguido el procedimiento de búsqueda pero sigo sin
encontrar un código que funcione.
Vuelva a intentar el procedimiento de búsqueda después de
borrar la programación de las teclas de dispositivo como se
indica:
a. Oprima y sostenga SETUP hasta que la tecla de dispositivo
parpadee dos veces.
b. Ingrese 9 9 2.
c. Oprima y suelte dos veces la tecla de dispositivo cuya
programación interesa borrar.
1. Oprima y sostenga SETUP en el control remoto hasta
que parpadee dos veces la tecla del último dispositivo
seleccionado.
Uso de la Tecla Master Power
2. Ingrese 9 9 3. La tecla correspondiente al último dispositivo
seleccionado deberá parpadear dos veces.
AVISO: A cada tecla de dispositivo ociosa se le puede asignar
sólo un dispositivo a la vez.
Esta Garantía reemplaza cualesquiera otras responsabilidades
o garantías expresas. CUALESQUIERA GARANTÍAS IMPLÍCITAS,
INCLUYENDO CUALQUIER GARANTÍA IMPLÍCITA DE COMERCIABILIDAD
O ADAPTABILIDAD PARA UN PROPÓSITO EN PARTICULAR ESTARÁN
LIMITADAS A LA DURACIÓN DE ESTA GARANTÍA. EN NINGÚN CASO
LA COMPAÑÍA SERÁ RESPONSABLE POR DAÑOS EMERGENTES O
INCIDENTALES. Ninguna persona ni representante está autorizado a
asumir, a nombre de la Compañía, ninguna responsabilidad salvo la
expresada aquí en conexión con la venta de este producto. Algunos
estados/provincias no permiten limitaciones sobre la duración de una
garantía implícita o la exclusión o la limitación de daños incidentales o
emergentes, de modo que es posible que las limitaciones o exclusiones
anteriores no apliquen en su caso. Esta Garantía le confiere derechos
legales específicos; según el estado/provincia, puede disfrutar además de
otros derechos.
El Control Remoto modelo RCRP05B tiene una característica
única que permite encender o apagar secuencialmente hasta
cinco dispositivos de entretenimiento en el hogar oprimiendo
una sola tecla.
3. Oprima VOL+ una vez. La tecla del último dispositivo
seleccionado deberá parpadear cuatro veces.
Desbloqueo del Control de Canales
1. Oprima una vez la tecla CBL/SAT del control remoto, la cual
deberá parpadear una vez. Oprima y sostenga SETUP hasta
que la tecla CBL/SAT parpadee dos veces.
DVD/VCR como tecla de 2.º AUD
DVD/VCR—>SETUP—>9—>9—>2—>AUD—>DVD/VCR
DVD/VCR como tecla de 2.º TV
El control remoto no hace encender una combinación de
TV/VCR marca Sony o Sharp.
Para encender estos productos, es necesario programar el
código de TV en el control remoto. Para productos Sony, use
el código de TV 0000 y el código de VCR 0032. Para productos
Sharp, use el código de TV 0093 y el código de VCR 0048.
AVISO: MASTER POWER (POWER) funciona sólo en el modo
CBL/SAT. Si no se ha programado, sólo se encenderán o
apagarán el aparato de cable o el receptor de satélite. En
cualquier otro modo, al oprimir MASTER POWER (POWER) una
vez, se enciende o apaga el dispositivo seleccionado.
Control del Volumen Sólo en un Modo (Bloqueo
General de Volumen)
DVD/VCR—>SETUP—>9—>9—>2—>TV—>DVD/VCR
DVD/VCR como tecla de 2.º CBL/SAT
2. Ingrese 9 7 3. La tecla CBL/SAT deberá parpadear dos veces.
3. Oprima CH- una vez. La tecla CBL/SAT deberá parpadear
AVISO: Los controles de volumen del modo de audio están
activos sin importar la configuración del bloqueo de volumen.
Sin embargo, si se programan los controles de volumen para
funcionar sólo en el modo AUD, se podrá regular el volumen
de los dispositivos de audio en todos los demás modos (p.
ej., DVD/VCR, DVR/AUX, TV o CBL/SAT). Esto puede resultar
ventajoso si, por ejemplo, uno siempre escucha sus dispositivos
de entretenimiento en el hogar a través de los altavoces del
receptor.
cuatro veces.
DVD/VCR—>SETUP—>9–>9–>2–>CBL/SAT—>DVD/VCR
DVD/VCR de nuevo como DVD/VCR
Ahora el control remoto permitirá cambiar el canal del televisor
o de la VCR en los modos TV y VCR.
Programación de la Tecla Master Power
1. Oprima y sostenga SETUP en el control remoto hasta
que parpadee dos veces la tecla del último dispositivo
seleccionado.
Para obtener mayor información, visite
Línea de Ayuda para el Cliente: 1-800-420-7968
DVD/VCR—>SETUP—>9–>9–>2–>DVD/VCR—>DVD/VCR
Para reasignar otra tecla de dispositivo ociosa, úsela en lugar de
la tecla DVD/VCR y realice la secuencia de pasos. Por ejemplo,
para reasignar una tecla AUD ociosa a un segundo DVD:
AUD—>SETUP—>9—>9—>2—>DVD—>AUD.
EE.UU.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,
New York 11788
CANADÁ: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit 3,
Door 16, Mississauga, Ontario L5T 3A5
2. Ingrese 9 9 5. La tecla correspondiente al último dispositivo
seleccionado deberá parpadear dos veces.
3. Oprima POWER una vez.
Marca(s) Registrada(s)
RCRP05B US IB 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|