Model: SPS36123
15.4” Kitchen LCD TV / DVD Combo
OWNER’S MANUAL
RCA SPS36123 Eng IB W011.indd
1
8/18/2009 4:29:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SAfETy PRECAUTiONS
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
WARNiNG:Changesormodificationstothisunitnotexpresslyapprovedbythepartyresponsibleforcompliance
could void the user’s authority to operate the equipment.
Warnings:
•
The mains plug is used as disconnect device and it should remain readily operable during intended used. In
order to disconnect the apparatus from the mains completely, the main plug should be disconnected from
the mains socket outlet completely.
•
•
Minimum 10 cm (4 inches) distances around the apparatus for sufficient ventilations.
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper,
table-cloths, curtains, etc.
•
The use of apparatus in moderate climates.
On Placement
•
•
Do not use the unit in places which are extremely hot, cold, dusty, or humid.
Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or
by placing it on carpeting.
On Safety
•
When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord
may damage it and create a hazard.
On Condensation
•
When left in a heated room where it is warm and damp, water droplets or condensation may form inside the
unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1
to 2 hours before turning the power on, or gradually heat the room and allow the unit to dry before use.
Note on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and 5,583,936 licensed
for limited viewing uses only.
ThisproductincorporatescopyrightprotectiontechnologythatisprotectedbyU.S.patentsandotherintellectual
property rights.Use of this copyright protection technology must be authorized by Macrovision, and is intended
forhomeandotherlimitedviewingusesonlyunlessotherwiseauthorizedbyMacrovision. Reverseengineering
or disassembly is prohibited.
2
RCA SPS36123 Eng IB W011.indd
3
8/18/2009 4:29:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
iMPORTANT SAfETy iNSTRUCTiONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufac-
turer, or sold with the apparatus.When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods
of time.
Portable Cart Warning
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord or plug is damaged, liquid has spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
•
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on apparatus.
•
Always leave sufficient space around the product for ventilation. Do not place product in or on a bed, rug,
in a bookcase or cabinet that may prevent air flow through vent openings.
•
•
•
•
Do not place lighted candles, cigarettes, cigars, etc. on the product.
Connect power cord only to AC power source as marked on the product.
Care should be taken so that objects do not fall into the product.
Do not attempt to disassemble the cabinet. This product does not contain customer serviceable
components.
IF YOUR PRODUCT OPERATES ON BATTERIES, adhere to the following precautions:
A. Do not mix old and new batteries.
B. Do not mix alkaline, standard (carbon-zinc), or rechargeable (NiCd, NiMH, etc) batteries.
C. Any battery may leak electrolyte or explode if disposed of in fire or an attempt is made to charge a battery
not intended to be recharged.
D. Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.When
discarding batteries, be sure to dispose of them in the proper manner, according to your state/provincial
and local regulations.
E. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
3
RCA SPS36123 Eng IB W011.indd
4
8/18/2009 4:29:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TAbLE Of CONTENTS
Safety Precautions .......................................... 1-2
Repeat Playback ................................................19
Programmable memory ....................................20
DVD programmed Memory...............................20
CD programmed Memory...............................20
viewing jPeg Files ...........................................21
Viewing jpeg Files ...........................................21
Customizing the Function Settings............ 21-22
Language Setup.............................................21
Video Setup...................................................22
System Setup.................................................22
Using the Tv .................................................23-24
Important Safety Instructions ............................ 3
Table of Contents ................................................ 4
Disc Formats........................................................ 5
Accessories ......................................................... 6
Remote Control.................................................... 6
Control Reference guide ................................7 - 9
mounting Instructions.................................. 10-11
Connections.................................................. 12-13
Connecting the TV Antenna ......................... 12
Connecting the Unit to a TV or Other Video
Equipment..................................................... 12
Scanning for TV Channels Automatically (Only
AppearstotheFirstTimePowerOn).....................23
Connecting the AM LOOP Antenna..................... 12
Plugging in the Unit....................................... 13
monitor Operation ............................................ 13
Unit Operation ................................................... 14
Sound System ................................................... 14
Setting the Clock .............................................. 15
Setting the Cooking Timer................................ 15
Playing a Disc ............................................... 16-18
Playing a Disc................................................ 16
Pausing Playback(StillMode).............................16
Stopping Playback......................................... 16
Skipping to a Different Chapter/Track............ 16
Fast Forward/Fast Reverse ........................... 16
Angle Selection ............................................. 17
Subtitle Selection .......................................... 17
Audio Selection ............................................. 17
Display Function ........................................... 18
Special Function ..........................................18
Locating a Specific Title/Chapter(DVD)......... 18
Locating a Specific Time. .............................. 18
TV Channel Setting............................................23
Channel Skip ...................................................24
Channel Label ...................................................24
Watching Television.....................................24
Tv Setup .......................................................25-28
Picture Setting...............................................25
Audio Setting..................................................25
Time Setting...................................................26
Setup Menu.................................................26-27
OSD Language............................................26
Closed Caption.......................................26-27
Restore Setting...........................................27
Parental Setup............................................27-28
Password...................................................27
Parental Control....................................27-28
Listening to the Radio ......................................29
Troubleshooting guide......................................30
maintenance ......................................................31
Specifications ...................................................31
4
RCA SPS36123 Eng IB W011.indd
5
8/18/2009 4:29:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
DiSC fORMATS
The unit can play
DVDs
[8cm/12cm disc]
Compatible
Audio CDs
[8cm/12cm disc]
Region management Information
RegionManagementInformation:ThisunitisdesignedandmanufacturedtorespondtotheRegionManagement
Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the
region number of this unit, this unit cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the “
” symbol appears on the screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD manufacturer determines the specific functions. Certain
functions may not be available on some discs. Be sure to read the documentation provided with the DVD.
Icons Used on DvDs
Language selections for audio
Sample Icons
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator
NOTE:
When playing a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images
will not be shown.
Titles, Chapters and Tracks
•
DVDs are divided into “titles” and “chapters”. If the disc
has more than one movie on it, each movie would be a
separate “title”. “Chapters” are sections of titles.
•
Audio CDs are divided into “tracks”. A “track” is usually
one song on an Audio CD.
NOTE: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded
on them, but some do not.
Note on Unauthorized Discs
You may not be able to play back some DVDs on this unit if they were purchased from outside your
geographic area or made for business purposes.
5
RCA SPS36123 Eng IB W011.indd
6
8/18/2009 4:29:44 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORiES
Please Check and Identify the Included Accessories.
Remote control ..............................................................................................................................x 1
AAA 1.5V battery...........................................................................................................................x 2
Mounting template.........................................................................................................................x 1
1.06” (27mm) spacers....................................................................................................................x 4
.57” (14.4mm) spacers...................................................................................................................x 4
#M 5 x 69 mm screws....................................................................................................................x 4
AM LOOP antenna ........................................................................................................................x 1
REMOTE CONTROL
Using the Remote Control
•
This remote control is magnetic and can be attached to most refrigerators. Some refrigerators panels are
not metallic. In this case, try attaching the magnetic remote control to the side of the refrigerator.
Point the remote control at the REMOTE SENSOR located on the unit.
When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be
degraded, causing unreliable operation.
•
•
•
The recommended effective distance for remote operation is about 16 feet (5 meters).
To Install Batteries
1. Open the battery door.
2. Insert two AAA batteries.
Battery Replacement
When the batteries become weak, the operating distance of the remote control is greatly reduced and you
will need to replace them.
Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
NOTE:
•
•
Do not place the remote control near magnetic devices or magnetic cards.
If the remote control is not going to be used for a long time, remove the batteries to avoid corrosion damage
caused by battery leakage.
•
Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries.
•
•
•
Always remove batteries as soon as they become weak.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
Weak batteries can leak and severely damage the remote control.
WARNING: Do not dispose of batteries in a fire. Batteries may explode or leak.
CAUTiON: When discarding batteries, environmental problems must be considered and local rules or laws
governing the disposal of these batteries must be strictly followed.
6
RCA SPS36123 Eng IB W011.indd
7
8/18/2009 4:29:44 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL REfERENCE GUiDE
Remote Control
1) MUTE
button
Press to turn off the sound.
2) STANDby/ON button
Turns on the unit and puts it in standby
mode.
1
2
3
4
5
6
3) DiSPLAy button
Changes disc status information displayed
on the screen.
4) PiCTURE button
Selects from preset screen display settings to
match the type of show you are watching.
5) RETURN/ EXiT
button
7
Press to exit theTV menu and return directly
to normal viewing.
6) ANGLE button
8
During DVD playback, switch the camera
angle of the video presentation when scenes
with multiple camera angles are recorded on
a DVD.
9
10
7) DVD MENU button
Press to enter the main menu of the DVD
you are watching.
8) CURSOR (
,
,
,
) buttons
11
12
13
Use to highlight selections on a screen and
make adjustments to certain settings.
CH+ / CH- buttons
Use to change TV channels.
ENTER button
Confirm selections on a menu screen.
9) VOLUME (+/-) buttons
Adjusts the volume.
10) STOP/bAND button
Stops playback.
Switches between AM and FM.
11)
PREV button
Selects previous title, chapter or track on a
disc.
Selects previous preset station in radio
mode.
12) Number (0-9) buttons
13) fORMAT button
Press to set size of LCD display (LCD Off,
full, 4:3).
7
RCA SPS36123 Eng IB W011.indd
8
8/18/2009 4:29:45 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL REfERENCE GUiDE
Remote Control
14) fUNCTiON button
Use to select DVD, TV or RADIO mode.
15) GOTO button
Goes directly to a programmed location on a
DVD/CD.
16) SUbTiTLE button
Selects one of the subtitle languages
programmed on a DVD.
17) AUDiO button
14
15
16
17
18
Selects audio soundtracks of a DVD or
changes the output mode of a CD.
MTS button
Press to select MONO sound, STEREO
sound or Secondary Audio Program (SAP).
18) SOUND button
19
Press to select from preset sound settings to
match the type of show you are watching.
19) TV MENU button
Press to display the on-screen TV menu.
20) PAUSE button
Pauses playback, frames advance.
21) PLAy button
Starts playback.
22)
23)
NEXT button
Selects next title, chapter or track on a disc.
Selects next preset station in radio mode.
20
21
22
TUNiNG
buttons
Scans all available radio stations.
: Fast reverse playback.
23
24
: Fast forward playback.
24) LAST CH button
25
Press to switch repeatedly between the last
two channels displayed.
25) MEMORy button
Sets title/chapter/track in a favorite order.
Enters the number of a selected station.
• [dot] button
26
Press to enter digital sub-channels (i.e.11.3,
12.7).
26) SETUP button
Enters and exits the SETUP menu of the DVD
in STOP mode.
REPEAT button
Repeats chapter or title of a DVD.
Repeats single track or whole CD.
8
RCA SPS36123 Eng IB W011.indd
9
8/18/2009 4:29:46 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL REfERENCE GUiDE
Unit
1
2
3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
1) Disc Tray
Usetosearchforastationautomaticallyorselect
presetted stations.
Press OPEN/CLOSE button to open or close
the tray.
10)
/CH
button
Place a disc on the disc tray, label side up.
2) Display Window
Press to advance to chapters / tracks in DVD
mode.
Displays system information.
3) Remote Sensor
Press to change TV channel in TV mode.
Usetosearchforastationautomaticallyorselect
presetted stations.
Receives the remote control unit signals.
11) VOL+ / button
4)
5)
6)
ON/Off button
Turns the unit on and off.
PLAy button
Press to start or resume playback of a disc.
/AM/fM button
Stops playing a disc.
Increases the volume level.
Makes adjustments to certain settings.
12) VOL- / button
Decreases the volume level.
Makes adjustments to certain settings.
13) TV MENU button
Switches between AM and FM.
Opens and closes the TV menu.
14) SET CLOCK button
Use to set the current time.
15) DVD/TV/RADiO button
Use to select DVD, TV or RADIO mode.
7) TiMER button
Use to set the cooking timer.
8) ENTER button
Usetoenterthesub-menuandconfirmselections
on a menu screen.
16)
OPEN/CLOSE button
9)
/CH
button
Use to open / close the disc tray.
17) Screen
Press to go back to previous chapters / tracks
in DVD mode.
Press to change TV channel in TV mode.
9
RCA SPS36123 Eng IB W011.indd 10
8/18/2009 4:29:47 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTiNG iNSTRUCTiONS
TOOLS NEEDED: 1) Electric drill with 1/4” bit; 2) Phillips-head (cross style) screwdriver.
STEP 1
STEP 3
If your cabinet does NOT have an overhang:
If your cabinet does NOT have an overhang:
a) Place the Mounting Template in the desired
location inside or underneath the cabinet
(whichever has less obstructions, and will be
easier for you to reach to drill holes), flush with
the front edge of the cabinet and tape it down.
Go to STEP 2.
If your cabinet DOES have an overhang:
a) Measure the thickness “T” of the cabinet
overhang (see Figure 1).
a) Eight screws are included with this unit, but you
will only need four of them. Select the screw
length which will go completely through your
cabinet bottom, and provide at least 3/8”of thread
to screw into the main unit.
b) Insert the four selected screws through each hole
from the inside of the cabinet going down (see
Figure 4).
Mounting
Screw
Cabinet Bottom
Front
Edge
T
Figure 1
b) Fold the Mounting Template along the guideline
that is closest to the thickness of your cabinet
overhang.
Figure 4
c) Tape Mounting Template to the underside of the
cabinet with the folded portion of the Mounting
Template flush up against the cabinet overhang
(see Figure 2). Go to STEP 2.
c) Hold the unit up against the bottom of the cabinet,
and align the four holes on the top of the unit with
the screws. Partially tighten each screw, but do
not fully tighten the screws until all of them have
been started.
d) Gently tighten each screw until they are firmly
holding the unit in place.
Cabinet Bottom
Front
If your cabinet DOES have an overhang:
a) Four screws are included with this unit. Make
sure the screws will go completely through your
cabinet bottom, and extend at least 3/8” past the
bottom of your cabinet overhang.
Edge
Template
Figure 2
STEP 2
b) This unit includes two sets of four spacers of
various lengths.The spacers can be put together
to form longer spacers to accommodate various
cabinet overhang thicknesses. Determine the
best combination of spacers which is equal to or
longer than the cabinet overhang thickness.
Use an electric drill with a ¼” drill bit (not included) to
drill all four holes marked on the Mounting Template
(see Figure 3). To reduce splintering, place a small
piece of masking tape over each hole location before
drilling. Go to STEP 3.
Template
Figure 3
(Continued on next page)
10
RCA SPS36123 Eng IB W011.indd 11
8/18/2009 4:29:48 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTiNG iNSTRUCTiONS
(Continued from previous page)
c) Insert the four selected screws through each
hole from the inside of the cabinet going down
(see Figure 5).
e) Partially tighten each screw, but do not fully
tighten the screws until all of them have been
started (see Figure 6).
Cabinet
Bottom
Mounting
Screw
Cabinet
Overhang
Spacers
Spacer
(optional)
Minimum
Equal to or
Longer than
Cabinet
Overhang
Figure 6
Figure 5
d) Hold each screw head down and push the unit
and spacers onto the screws, then hold the unit
up until spacers are firmly against the bottom
of the cabinet (and fully nested within each
other if you are using multiple spacers for each
screw).
f) Gently tighten each screw until they are firmly
holding the unit in place. The top front edge of
the unit should clear the overhang.
CAUTiON
TO REDUCE THE RiSK Of fiRE, DO NOT PLACE ANy HEATiNG OR COOKiNG
APPARATUS bENEATH THiS UNiT.
Mounting Suggestions
1) If your cabinet has obstructions inside it which prevent you from using the template, cut out the corresponding
area on the template, but do NOT cut out or through the screw holes.
2) If your cabinet has obstructions underneath it, which will interfere with the mounting of the unit, remove
the obstruction before mounting the unit, or find another location to mount the unit.
3) It is recommended that you wear safety glasses while drilling to prevent eye injuries.
4) For wood cabinets, you may want to mark the hole locations with a nail, pressed gently but firmly into
the wood so that a slight impression is made. This will also help keep the drill bit centered in the right
location.
5) Hold the drill firmly against the cabinet to keep the drill from “walking”.
11
RCA SPS36123 Eng IB W011.indd 12
8/18/2009 4:29:48 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTiONS
Connecting the Tv Antenna
Connect a TV antenna or CATV cable or Satellite system to the TV antenna terminal.
TV antenna
To the TV ANT IN
terminal
2
FM ANT
1
VIDEO
OUT
TV
ANT IN
AM
LOOP ANT
Connecting the Unit to a Tv or other video equipment
Use the Video cable (not supplied). Connect the VIDEO OUT on the rear of the unit to the VIDEO IN on your
TV or other video equipment.
FM ANT
VIDO
OT
TV
ANT IN
AM
LOOP ANT
TV or other video
Equipment
(yellow)
VIDEO
IN
Video cable (not supplied)
Connecting the Am LOOP Antenna
Connect the AM LOOP antenna (included) to the AM LOOP ANT terminal.
FM: Fully unwind the antenna wire and position it for the best reception.
AM: Fully unwind and rotate the loop antenna, then position it for the best reception.
FM ANT
VIDEO
OUT
TV
ANT IN
AM
LOOP ANT
12
RCA SPS36123 Eng IB W011.indd 13
8/18/2009 4:29:49 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTiONS
Plugging in the Unit
Plug the AC power cord into the wall outlet
a) Before plugging in the power cord, make sure the voltage of the unit matches your local voltage.
b) Plug the power cord directly into the nearest wall outlet, and wrap the remaining cord around the cord
storage knob at the rear of the unit.
CAUTiON:
TO PREVENT ELECTRiC SHOCK, MATCH WiDE bLADE Of PLUG TO WiDE SLOT Of WALL OUTLET,
THEN fULLy iNSERT.
FM ANT
AC power cord
VIDEO
OUT
TV
ANT IN
AM
LOOP ANT
To AC outlet
MONiTOR OPERATiON
Follow the illustrations below to open the monitor.
1. Gently pull the monitor down from the back, and twist it clockwise so the screen is visible.
2. The screen can be turned up to 270o. Do NOT force the screen once it stops turning.The screen does
NOT turn completely around.
13
RCA SPS36123 Eng IB W011.indd 14
8/18/2009 4:29:50 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
UNiT OPERATiON
Turning the Unit On
While the power cord is connected and the unit is on standby, power will be consumed and only the clock
display will flash.
•
Press the ON/Off button to turn the unit on, “DVD” will appear on the front display.
After a short period of time, the DVD logo (start-up picture) will appear on the screen.
•
Press the DVD/TV/RADiO button (the fUNCTiON button on the remote control) to TV mode, “TV” will
appear on the front panel display.
After a short period of time, and the TV program will begin on the screen.
•
Press the DVD/TV/RADiO button (the fUNCTiON button on the remote control) to RADIO mode, FM
frequency will appear on the front panel display.
After a short period of time, the station will begin.
SOUND SySTEM
Dolby Digital (for DvD)
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-
channel listening.An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel
soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
‘Dolby’ and
the double-D symbol are trademarks of Dolby Laboratories.
14
RCA SPS36123 Eng IB W011.indd 15
8/18/2009 4:29:50 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTiNG THE CLOCK
To adjust the clock, the unit must be in standby mode. To enter standby mode, make sure that the unit is
plugged in, but not turned on.
•
Check that the rated voltage of the unit matches your local voltage.
1. When the AC power cord is plugged in, the clock
display will blink.
3. Press the
/
buttons to set the current
hours then press the SET CLOCK button once
to confirm. The MINUTES will now blink.
2. Press the SET CLOCK button until the HOUR
4. Press the
/
buttons to set to desired time
blinks.
then press the SET CLOCK button once to start
the clock.
SETTiNG THE COOKiNG TiMER
1. Press the TiMER button. The “TIMER” indicator
3. When the preset time elapses, the ALARM will
sound.
appears and the cooking time “10” blinks.
4. To turn OFF the ALARM, press the TiMER button
once. Otherwise, the ALARM will automatically
turn off after 60 minutes if no button is pressed.
2. Press the
/
buttons to select your desired
time from 1-99 minutes.
•
Press the TiMER button repeatedly to select
following preset times: 10, 15, 30, 45, 60, 75, 90
minutes. You can then “fine-tune” your time by
using the
Press and hold the
forward/reverse to desired time.
/
buttons on the unit.
•
/
buttons to fast
Cancelling the Cooking Timer
•
Press the TiMER button until the time of the cooking timer shows “OF F ”. The “TIMER” indicator will
disappear.
15
RCA SPS36123 Eng IB W011.indd 16
8/18/2009 4:29:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAyiNG A DiSC
This owner’s manual explains the basic instructions of this unit. Some DVDs are produced in a manner
that allows specific or limited operation during playback. Such as, the unit may not respond to all
operating commands. This is not a defect in the unit. Refer to the instruction notes of discs.
“
” may appear on the screen during operation. A “
”means that the desired operation is not
permitted by the unit or disc.
Playing a Disc
1. Press the ON/Off button to turn on the unit.
2. Press the DVD/TV/RADiO button (the fUNCTiON button on the remote) to select DVD mode.
See CUSTOMiZiNG THE fUNCTiON SETTiNGS (page 21 to 22) before proceeding to step 3.
3. Press the OPEN/CLOSE button. The disc tray opens.
4. Place a disc onto the disc tray with the label side up.
5. Press the OPEN/CLOSE button. The disc tray closes.
It takes a short while for your unit to load the disc. After loading, the unit will automatically either bring you
to the main menu of the DVD or start playback of the disc.
6. If the unit does not automatically start playing the DVD, press the PLAy button.
•
When MUTE is pressed, the sound is mute and the “L O”
indicator always blinks on the LCD display until MUTE is pressed
again or VOL is pressed.
Pausing Playback (Still mode)
Press the PAUSE button on the remote control.To resume normal playback, press the PLAy button.Each
time you press the PAUSE button, the picture advances one frame.
Stopping Playback
Press the button at the location where you want to interrupt playback. To resume playback at the position
where the disc was stopped, press the PLAy button.
If you press the button twice, the unit’s memory will be cleared and pressing the PLAy button will reset
the disc to the beginning.
Skipping to a Different Chapter/Track
•
•
•
Press the
Press the
PREV button repeatedly to skip to the start of the current or previous chapter/track.
NEXT button to skip to the next chapter/track.
For an audio CD, use the number buttons (remote control only) to go directly to that track number.
Fast Forward/Fast Reverse
1. Press the TUNiNG
or
TUNiNG button on the remote control when a disc is playing.
•
The disc begins fast scan at x2 speed.
•
Six speeds are available. Each time the TUNiNG
fast scan changes in the following sequence:
or
TUNiNG button is pressed, the speed of
2. Press the
speed.
PLAy button when you have reached the desired point to resume playback at normal
NOTE:
•
The DVD player mutes sound during reverse and forward scan of DVD video discs.
•
The fast playback speed may differ depending on the disc.
16
RCA SPS36123 Eng IB W011.indd 17
8/18/2009 4:29:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAyiNG A DiSC
Angle Selection
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the
same scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles
recorded, press the ANGLE button to view the number
Sequence of angle shots
of current angles available.
(Example)
2. Press the ANGLE button repeatedly to change the
scene to the next angle in those recorded.
•
About two seconds later, playback continues from
the new angle selected.
•
If no button is pressed within 10 seconds, playback
continues without changing the current angle.
NOTE:
•
This function can only be used for discs on which scenes shot from multiple angles have been recorded.
•
If only one angle is recorded, “ ” is displayed.
Subtitle Selection
1. While a DVD is playing, press the SUbTiTLE button to display the current language setting, as shown in
the example below.
2. Press the SUbTiTLE button repeatedly to select the desired subtitle language.
Subtitle: English 1/3
NOTE:
•
•
•
•
•
•
If only one language is recorded, the language does not change.
About two seconds later, playback continues with the new subtitle selected.
The number of languages recorded differs depending on the disc.
If no button is pressed within a few seconds, playback continues without changing the current subtitle.
This function can only be used for discs on which subtitles have been recorded in multiple languages.
On some DVDs, subtitles are activated from the main menu of the DVD. Press the DVD MENU button to
activate the main menu.
Audio Selection
On some discs, the sound is recorded in two or more formats. Follow the directions below to select the type
of playback.
1. While a disc is playing, press the AUDiO button to show the current audio format number.
2. Press the AUDiO button repeatedly to select the desired audio format.
English 1/3
NOTE:
•
If only one audio format is recorded, the number does not change.
•
Some DVD discs allow you to change audio selections only via the disc menu. If this is the case, press the
DVD MENU button and choose the appropriate language on the disc menu.
You can select different audio channels (Left, Right or Stereo) on an audio CD by pressing the AUDiO
button repeatedly.
•
17
RCA SPS36123 Eng IB W011.indd 18
8/18/2009 4:29:54 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAyiNG A DiSC
Display Function
While the disc is playing, press the DiSPLAy button on the remote control repeatedly to display information
on operation status.
DVD
CD
Single Elapsed
Single
Elapsed
Total
SPECiAL fUNCTiON
Locating a Specific Title/Chapter
If a DVD contains title/chapter numbers, you can locate a specific title/chapter by directly selecting a title/
chapter number.
1. In STOP/PLAY mode, press the GOTO button.
2. Press the
press the
or
or
button to highlight a specific field and
button button to select the title/chapter
you want.
3. Press the ENTER button to confirm. Playback starts from
the selected title/chapter.
Locating a Specific Time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button twice for DVD (once for CD), a
screen shown as right will be displayed on the screen.
2. Enter the corresponding number buttons for the setting point
you want.
3. Press the ENTER button to confirm. Playback starts from
the selected location.
NOTE:
•
If the time numbers you entered is not permited by the disc, after you press the ENTER button,
appear on the screen.You should reset and enter correct numbers.
Some discs may not respond to this process.
Some scenes may not be located as precisely as specified.
This method for accessing specific locations is available only within the current title of the disc.
will
•
•
•
18
RCA SPS36123 Eng IB W011.indd 19
8/18/2009 4:29:55 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
REPEAT PLAybACK
You can play a specific title, chapter or track repeatedly. (Title repeat, chapter repeat, entire DVD repeat)
Repeating a Chapter
You can play the same chapter repeatedly.
While the disc is playing, press the REPEAT button repeatedly until the
indicator displays on the
screen. The current chapter is played repeatedly.
Repeating a Title
You can play the same title repeatedly.
While the disc is playing, press the REPEAT button repeatedly until the
screen. The current title is played repeatedly.
indicator displays on the
indicator displays on the screen.
indicator displays on the
Repeating an entire DISC
While the disc is playing, press the REPEAT button repeatedly until the
The entire disc is played repeatedly.
To Resume Normal Playback
While the disc is playing, press the REPEAT button repeatedly until the
screen.
You can play a single track or an entire disc repeatedly.
Repeating a Single Track
You can play the same track repeatedly.
While the disc is playing, press the REPEAT button repeatedly until the indicator
displays on the
screen. The current track is played repeatedly.
Repeating an entire DISC
While the disc is playing, press the REPEAT button repeatedly until the
indicator displays on the screen.
The entire disc is played repeatedly.
To Resume Normal Playback
Press the REPEAT button repeatedly until the
indicator displays on the screen.
19
RCA SPS36123 Eng IB W011.indd 20
8/18/2009 4:29:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMAbLE MEMORy
DvD Programmed Playback
You can combine your favorite titles/chapters and play them in the order you determine.
1. Press the MEMORy button in PLAY/STOP mode. A screen will be
shown as right.
2. Press the button to highlight the Title. Press the
chooseadesiredtitle.Pressthe buttonagaintohighlightaChapter.
Press the or button to choose the desired Chapter. Press the
or
button to
ENTER button to confirm.The highlight bar will move to the next item
automatically.
3. Repeat step 2 to add additional titles and chapters.
4. Press the PLAy button to start the programmed playback.
To Change the programmed selections
PROGRAM
1. Press the MEMORy button.
Title
Chapter
2. Press the button to clear one item, then press the button to clear
them one by one.
3. Followabovestep2ofTitle/ChapterProgrammedPlaybacktoprogram
the new title and chapter.
4. Press the PLAy button to start the programmed playback.
Select
Play
Clear
To Resume Normal Playback from Programmed Playback
1. Press the MEMORy button.
2. Press the button to clear, then press the
items one by one.
button to clear all the
3. Press the PLAy button twice to resume normal playback.
NOTE:
•
•
•
Some discs may not permit memory playback operation.
To exit the Program menu, press the MEMORy button.
The programmed selections will be cleared when you open the disc tray or turn off the DVD player.
CD Programmed Playback
Track
1. Press the MEMORy button in PLAY/STOP mode. A screen will be
shown as right.
2. Press the
button to highlight track. Press the
or
button to
choose the desired track.
3. Press the ENTER button to confirm. The highlight bar will move to
the next item automatically.
PROGRAM
Track
4. Repeat step 2 to add additional tracks.
Play
Clear
Select
20
RCA SPS36123 Eng IB W011.indd 21
8/18/2009 4:29:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ViEWiNG JPEG fiLES
This unit can play JPEG files written to CD-R/RW discs.
viewing jPeg Files
1. Open the disc tray.
2. Place a disc onto the disc tray with the label side up.
3. Close the disc tray. Slide show starts automatically.
4. Press the button to display a folder list. Press the or button to
select your desired file, the selected picture will appear in the lower
left corner.
File Number:
ROOT
5. Press the PLAy button to start playback.
634x476 2009/07/01
NOTE:
•
You can press the PAUSE button to freeze the picture, and press the PLAy button to resume slide
show.
•
•
•
•
You can press the button to quit playback.
You can use the number buttons on the remote control to jump immediately to the desired picture.
You can press the ANGLE button on the remote control to rotate direction of the picture by 90o.
Some discs may not permit this operation.
Repeating
Track
1. While the picture is playing, press the REPEAT button until the
The current track is played repeatedly.
2. While the picture is playing, press the REPEAT button again, the
The folder is played repeatedly.
indicator displays on the screen.
indicator displays on the screen.
Folder
All
3. While the picture is playing, press the REPEAT button once more, the
screen. All tracks is played repeatedly.
indicator displays on the
4. To resume normal playback, press REPEAT button once again, the
screen.
indicator displays on the
Picture mode
While the picture is playing, press the Picture button repeatedly to select your preferred option (Standard,
Movie, Dynamic, Soft, Personal).
CUSTOMiZiNG THE fUNCTiON SETTiNGS
Language Setup
1. In STOP mode, press the SETUP button.
2. Use the
or
button to select the option Language Setup.
3. Press the
Language.
or ENTER button to move the highlight bar on OSD
4. Use the or ENTER button to move the highlight bar, then use the
or button to select your preferred language, and press the ENTER
button to confirm.
5. Press the button to go back to the previous menu. Repeat steps
3 and 4 to adjust other options.
Enter:
6. To exit the SETUP MENU and return to the normal screen, simply
press SETUP button or press the or button to highlight the Exit
Setup Mode and press the ENTER button.
NOTE:
•
Some DVDs may not play in the audio language selected. A prior language may be programmed on the disc.
•
Some DVDs may not include your pre-selected language.In this case, the DVD player automatically displays
disc menus consistent with the disc’s initial language setting.
21
RCA SPS36123 Eng IB W011.indd 22
8/18/2009 4:29:57 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMiZiNG THE fUNCTiON SETTiNGS
video Setup
1. In STOP mode, press the SETUP button.
2. Use the or button to select Video Setup.
3. Press the /ENTER button to highlight TV Type.
4. Press the /ENTER button to enter.
5. Use the
or
button to select the desired TV type and press the
ENTER button to confirm.
6. Press the button to go back to the previous menu.
7. To exit the SETUP MENU and return to the normal screen, simply
press SETUP button or press the or button to highlight the Exit
Setup Mode and press the ENTER button.
Enter:
Cut off when a wide-screen
video image is played.
TV Type
Pan Scan
•
When wide-screen video is played, this mode clips the right and
left sides of the image so that it can be viewed on a conventional
screen.
•
Some wide-screen DVDs that do not permit Pan Scan mode playback
are automatically played in letterbox mode (black bands that appear
at the top and bottom of the screen).
Letter box
When wide-screen video is played in this mode on a conventional
screen, black bands appear at the top and bottom of the screen.
Wide screen
•
•
This is the correct mode for playing wide-screen videos on the unit or
other external wide-screens.
NOTE:
•
•
•
The displayable picture size is preset on the DVD. Therefore the
playback picture of some DVDs may not conform to the picture size
you select.
When you play DVDs recorded in the 4:3 aspect ratio, the playback
picture will always appears in the 4:3 aspect ratio regardless of the
TV TYPE setting.
If the screen mode is still not correct, press the ENTER button
repeatedly to adjust it.
System Setup
1. In STOP mode, press the SETUP button.
2. Use the
3. Press the /ENTER button to enter.
4. Use the or button to select Default item.
or
button to select System Setup.
5. Press the /ENTER button to enter.
6. Use the or button to select the desired setup option and press
the ENTER button to confirm.
NOTE: If set as Yes, it takes 3-5 seconds to reset the DVD settings
to the factory default.
Enter:
7. Press the button to go back to the previous menu.
8. To exit the SETUP MENU and return to the normal screen, simply
press SETUP button or press the
or
button to highlight the
Exit Setup Mode and press the ENTER button.
22
RCA SPS36123 Eng IB W011.indd 23
8/18/2009 4:29:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
USiNG THE TV
Connect a TV antenna or CATV cable or Satellite system to the TV antenna terminal before scanning
for TV channels
Scanning for Tv Channels Automatically (Only appears to the first time power on)
1. Connect the TV antenna.
2. Connect the AC power cord.
3. Press the ON/Off button to turn on the unit.
4. Press the DVD/TV/RADiO button (the fUNCTiON button on
the remote control) to select TV mode.
5. Press the button to select “Yes”.
6. Press the ENTER button.
7. Press the
or button to select Antenna.
8. Press the or button to select Air.
Picture
Audio
Time
Setup
Parental
TV
9. Press the
or button to select Auto Scan.
10.Press the button to enter.
11.Press the /ENTER button.
RF CH
11
0
Found
12.The unit will immediately search all channels for those with
adequate signal strength and store those channels with
signals in memory. The unit will take a short minutes to finish
auto scan and after this is completed, the unit will switch to
the first channel found.
Select
Adjust
MENU Return
"ENTER"
Tv Channel Setting
1. Press the TV MENU button.
2. Use the or button to select TV.
3. Use the or button to select the options (Antenna / Auto
Scan / Auto Scan Add CH / Channel Skip / Channel No. /
Channel Label / DTV Signal).
4. Use the or button to make adjustment. The screen will
change to your selected mode immediately. Press the TV
MENU button to return to the previous menu.
5. Repeat steps 2 to 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press
the EXiT button on the remote control.
Picture
Audio
Time
Setup
Air
Parental
TV
Antenna
Auto Scan
Auto Scan Add CH
Channel Skip
Channel No.
Channel Label
DTV Signal
Select
Adjust
MENU Return
NOTE: Channel No. : 2-69 Channel for Air, 1-135 Channel for
Cable.
Antenna :
Select “Cable” to receive cable signals. Select “Air” to receive “over the air” (broadcast)
signals.
Auto Scan :
Automatically scan all channels for those with adequate signal strength.
Auto Scan Add CH: The already-stored channels will not be cleared and the newly-scanned channels will
be added.
If you have selected Cable in Antenna, then you can select Cable System (AUTO / STD / HRC / IRC) in the
submenu. We recommend you pick “AUTO”. “HRC” and “IRC” are custom station frequencies used by some
Cable Service Providers. “STD” refers to the standard frequencies used by many Cable Service Providers.
“AUTO” will cause the product to scan all frequencies.
Channel Skip:
You may switch ON/OFF the skip function of each stored channel by selecting the
channel with or button (and using or button to select page if the amount
of stored channels is more than 1 page), and followed with pressing the ENTER
button.
Channel No.:
Select a different TV channel.
DTV Signal:
Display the signal strength (for digital TV channels only).
23
RCA SPS36123 Eng IB W011.indd 24
8/18/2009 4:29:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
USiNG THE TV
Channel Skip
1. Press TV MENU button.
2. Use the or button to select TV.
Picture
No.
Audio
Time
Setup
Parental
Skip
TV
Program Name
3. Use the
4. Press the button to enter.
5. Press the or button to select a channel.
6. Press the button to select the last channel of the page;press
again to go to the next page. Press the button to select the
or
button to select Channel Skip.
2.0
3.0
4.0
5.0
6.0
7.0
8.0
xxx
On
Off
Off
On
Off
On
On
xxxxx
xxx
xxxxxx
xxxx
xxx
xxxxx
first channel of the page; press again to return the previous
page.)
Select
Adjust
MENU Return
7. Press the ENTER button to shift between On / Off. (Select On to skip the selected channel. )
8. Press the TV MENU button to return to the previous menu.
9. To exit the MAIN MENU and return to the normal screen, press the EXiT button on the remote control.
Channel Label
You can edit a label for each channel.
Picture
Audio
Time
Setup
Parental
TV
1. Press TV MENU button.
2. Use the or button to select TV.
3. Use the
or
button to select Channel Label.
X
4. Press the
button.
5. Use the or button to select the number or letter. Use the
or button to move and edit the next character.
6. Press the ENTER button to confirm.
Select
Adjust
MENU Return
7. After editing, the Channel and Channel Label will be shown on the screen when you press the DiSPLAy button.
Watching Television
Viewing a television station after the auto/manual search for channels.
1. Press the fUNCTiON button to TV mode.
2. Press the CH buttons to select a channel, or press the number
button on the remote control to select the channel you want
to watch. Or you may press the ENTER button to show the
Channel List, then use the or button to select a previous
or next channel.
Channel List
NO.
xxx
xxx
NAME
xxxxx
xxxxx
xxx
xxxxx
• For channels 1 to 9, enter one-digit channel number.
• For channels 10 to 99, enter the two-digit channel number.
• For channels 100 or over, enter three-digit channel number.
NOTE:
Prev
Next
• When a channel is selected, the channel number is displayed in the top right corner of the screen. This
number will disappear after a few seconds.
• When MUTE is pressed, the sound is mute and the “L O” indicator always blinks on the LCD display until
MUTE is pressed again or VOL is pressed.
ATSC TV mode:
Press the DiSPLAy button, the upper window will pop up, then press the DiSPLAy button again, the lower
window will pop up. Press the DiSPLAy button once to exit.
5.1
CC OFF
xxxxxxxxxxxxxxxxx
xxxxxxxx
HD 1920xX1080i Audio 1/2
2009/07/31 07:00 AM 07:00 AM-07:30 AM
TV-PG/
Bad
Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
NTSC TV mode:
Press the DiSPLAy button, the below window will pop up, then press the DiSPLAy button once to exit.
4.0
CC OFF
720x480I Stereo
Canada Eng C8+
24
RCA SPS36123 Eng IB W011.indd 25
8/18/2009 4:30:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
Picture Setting
1. Press the TV MENU button.
2. Use the or button to select Picture.
3. Use the or button to select the options (Picture Mode
/ Contrast / brightness / Color / Tint / Sharpness / Color
Mode).
Picture
Audio
Time
Setup
Parental
TV
Picture Mode
Contrast
Brightness
Color
Standard
50
50
50
0
4. Use the or button to make adjustment. The screen will
change to your selected mode immediately. Press the TV
MENU button to return to the previous menu.
Tint
Sharpness
Color Mode
50
Normal
Select
Adjust
MENU Return
5. Repeat steps 2 and 3 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press
the EXiT button on the remote control.
Picture Mode: Select from preset screen display settings to match the type of show you are watching
(Standard, Movie, Dynamic, Soft & Personal).
Contrast:
Adjust to sharpen the picture quality.The black portions of the picture become richer in darkness
and the white become brighter.
brightness:
Color:
Adjust to brighten or darken the whole picture.
Adjust the color of the picture.
Tint:
Sharpness:
Adjust natural skin tones in the picture quality.
Adjust the sharpness level to improve detail in the picture.
Color Mode: Adjust the three color temperature of the picture.Select Normal (balanced) / Warm (red white)
/ Cool (blue white) mode.
Audio Setting
1. Press the TV MENU button.
2. Use the or button to select Audio.
3. Use the or button to select the options (Sound Mode /
Picture
Audio
Time
Setup
Parental
TV
bass / Treble / balance / Audio Language/ MTS).
4. Use the or button to make adjustment. Press the TV
Sound Mode
Base
Standard
50
50
0
Balance
Treble
MENU button to return to the previous menu.
AudioLanguage
English
Mono
5. Repeat steps 2 to 4 to adjust other options.
MTS
6. To exit the MAIN MENU and return to the normal screen, press
Select
Adjust
MENU Return
the EXiT button on the remote control.
Sound Mode:
Select from preset sound settings (Standard, Music, Movie, Theatre, Personal) to match
the type of show you are watching.
bass:
Adjust the bass range.
Treble:
balance:
Adjust the treble range.
Adjust the balance level toward the left or right speakers.
Audio Language: Use the or button to select English, French or Spanish (Available for Digital TV
system only).
MTS(Multi Channel
Television Sound):
Use the or button to select Stereo/SAP(Secondary Audio Program)/Mono.
25
RCA SPS36123 Eng IB W011.indd 26
8/18/2009 4:30:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
Time Setting
1. Press the TV MENU button.
2. Use the or button to select Time.
Picture
Audio
Time
Setup
Parental
TV
3. Press the
4. Use the or button to make adjustment.
5. Use the or button to select the options (Time Zone,
Daylight Saving Time or Clock). Adjust them using the or
button.Press the TV MENU button to return to the previous
menu.
button to enter the time settings.
Time Zone
Eastern
Daylight Saving Time
Clock
Off
2009/12/31 07:00PM
Select
Adjust
MENU Return
6. Repeat step 3 to adjust other options.
7. To exit the MAIN MENU and return to the normal screen, press
the EXiT button on the remote control.
NOTE: Only for DTV/ATSC input source mode, thus it is not available in other input source mode.
Time Zone:
Select the time zone from Eastern / Central / Mountain / Pacific /
Alaska / Hawaii.
Daylight Saving Time:
Select On to activate daylight savings time.
Display the current time.
Clock:
Setup menu
OSD Language
Picture
Audio
Time
Setup
Parental
TV
1. Press the TV MENU button.
OSD Language
Closed Caption
Restore Setting
English
2. Use the or button to select Setup.
3. Use the or button to select OSD Language.
4. Use the or button to make adjustment.
5. Press the TV MENU button to go back to previous menu.
Select
Adjust
MENU Return
6. To exit the TV SETUP MENU and return to the normal screen,
press the EXiT button on the remote control.
Closed Caption
1. Press the TV MENU button.
Picture
Audio
Time
Setup
Parental
TV
2. Use the or button to select Setup.
3. Use the or button to select Closed Caption.
CC Mode
Off
Analog Closed Caption
Digital Closed Caption
CC1
Service1
4. Press the
button to enter.
Digital Capton Style
5. Press the or button to make adjustment.
6. Press the or button to move the highlight bar.
7. Press the TV MENU button to go back to previous menu.
Select
Adjust
MENU Return
8. To exit the TV SETUP MENU and return to the normal screen, press the EXiT button on the remote
control.
NOTE:
This function only works on ATSC programs broadcast with captions.
26
RCA SPS36123 Eng IB W011.indd 27
8/18/2009 4:30:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
CC Mode:
Select closed caption On, Off, CC on Mute.
Analog Closed Caption: Select the analog closed caption or turn it off.
Digital Closed Caption: Select the digital closed caption or turn it off.
Digital Caption Style:
Select As Broadcaster to use the default digital caption style of the broadcaster.
Select Custom to activate the caption style items and set your desired detailed
settings.
Restore Setting
1. Press the TV MENU button.
Picture
Audio
Time
Setup
Parental
TV
2. Use the or button to select Setup.
3. Use the or button to select Restore Setting.
4. Press the
button to enter.
Are you sure?
5. Press the or button to select “Yes”.
6. Press ENTER to confirm.
No
Yes
7. Press the TV MENU button to go back to previous menu.
Select
Adjust
MENU Return
8. To exit the TV SETUP MENU and return to the normal screen,
press the EXiT button on the remote control.
Parental Setup
Password
1. Press the TV MENU button.
2. Use the or button to select Parental.
3. Use the
button to select Enter Password. Enter a 4-digit
Picture
Audio
Time
Setup
_ _ _ _
Parental
TV
password. Once entered, the screen will enter the Parental
menu.
Enter Password
4. Press the
button to enter. Use the or button to make
adjustment. Press the TV MENU button to return to the
previous menu.
5. Repeat steps 2 to 4 to adjust other options.
6. To exit the MAIN MENU and return to the normal screen, press
Select
Adjust
MENU Return
the EXiT button on the remote control.
NOTE: If you forget the password, enter “8888” to unlock parental control.
Parental Control
1. Press the TV MENU button.
2. Use the or button to select Parental.
3. Use the
password.
button to select Enter Password. Input 4-digit
Picture
Audio
Time
Setup
Parental
TV
Change Password
System Lock
US
4. Use the
or button to select various Parental settings.
On
Adjust them using the or button, or press the button to
Canada
go into the detailed settings.
RRT Setting
Reset RRT
5. Press the TV MENU button to return to the previous menu.
6. Repeat steps 1 - 2 to adjust other options.
Select
Adjust
MENU Return
7. To exit the MAIN MENU and return to the normal screen, press
the EXiT button on the remote control.
27
RCA SPS36123 Eng IB W011.indd 28
8/18/2009 4:30:02 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SETUP
Change Password: Enter new password and confirm it. (Remember your password!)
System Lock:
US:
Select On to edit the following parental items. Select Off to disable parental control.
Set TV and MPAA ratigns.
Canada:
Set Canada English and Canada French ratings.
Set Rating Region Table.
RRT Setting:
Reset RRT:
Reset Rating Region Table to the default settings.
U.S. TV Ratings
TV-Y:
Recommended for all children.
TV-Y7: Recommended for all children age 7 and above.
TV-G: General Audience.
TV-PG: PARENTAL GUIDANCE Suggested.
TV-14: PARENTAL STRONGLY CAUTIONED.
TV-MA: Mature Audience Only.
U.S. MPAA Ratings
N/A:
G:
Not rated.
General Audiences, Suitable for all ages.
PG:
Parental Guidance Suggested - Some material may not be suitable
for children.
PG-13: Parents Strongly Cautioned - Some material may be inappropriate
for children under 13.
R:
Restricted, Under 17 requires accompanying parent or adult guard-
ian for viewing in movie theaters.
NC-17: No one 17 or under admitted in movie theaters,
X:
Adults Only.
Canadian English Ratings E:
C:
Exempt.
Children.
C8+:
Recommended for children age 8 and older.
General Audiences, Suitable for all ages.
G:
PG:
Parental Guidance Suggested - Some material may not be suitable
for children.
14+:
18+:
Viewers 14 years and older.
Adult Programming.
Canadian French Ratings
E:
Exempt.
G:
General Audiences, Suitable for all ages.
8 ans+: Not recommended for young children.
13 ans+: Not suitable for children under the age of 13.
16 ans+: Not suitable for children under the age of 16.
18 ans+: Adult Programming.
28
RCA SPS36123 Eng IB W011.indd 29
8/18/2009 4:30:02 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
LiSTENiNG TO THE RADiO
Tuning in to a Station manually
1. Press the DVD/TV/RADiO button (the fUNCTiON button on the remote
control) until the radio frequency appears on the front panel display.
2. Press the /AM/fM button to select AM or FM.
3. Press the
TUNiNG
buttons on the remote control to tune in to
a desired station.
•
When MUTE is pressed, the sound is mute and the “L O” indicator
always blinks on the LCD display until MUTE is pressed again or VOL
is pressed.
Fm Stereo
Press the MTS button on the remote control until “
” appears on the
front panel display.
Weak Fm stations
Press the MTS button on the remote control until “
” appears on the
front panel display. Background noise will be reduced. To restore stereo
reception, press the MTS button on the remote control to select “
”.
Searching for a Station Automatically
•
Press and hold the
CH
/
CH
button on the front panel or the
TUNiNG
buttons on
the remote control until the tuner starts searching for a station, then release. After tuning in a station, the
search stops.
•
The search may not stop at a station with a very weak signal.
Presetting Stations
The unit can store a total of 60 stations in memory (30 FM, 30 AM). Presetting allows you to tune in to a
station directly.
1. Press the DVD/TV/RADiO button (the fUNCTiON button on the remote control) to RADIO.
2. Press the /AM/fM button to select AM or FM.
3. Press the number button on the remote control to select the preset number.
•
•
For preset numbers 1 to 9, simply press the number button on the remote control.
For preset numbers 10 to 30, enter the two-digit numbers.
For example, to enter 18 by pressing “1” & “8”.
4. Press the
TUNiNG
buttons to tune in to a desired station.
5. Press the MEMORy button twice on the remote control.
6. Repeat steps 2-5 to store other stations.
Tuning in to a Preset Station
1. Press the DVD/TV/RADiO button (the fUNCTiON button on the remote control) to RADIO.
2. Press the /AM/fM button to select AM or FM.
3. Press the
PREV/
NEXT button repeatedly to select the number of the preset station or use the
numeric buttons to enter the number of the preset station.
For Better Reception
FM: Fully unwind the FM antenna wire. Then extend the FM antenna wire and place it in the position that
sounds best.
AM: Fully unwind and rotate the loop antenna then position it for the best reception.
NOTE: Do not connect the FM antenna to an outside antenna.
29
RCA SPS36123 Eng IB W011.indd 30
8/18/2009 4:30:03 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUbLESHOOTiNG GUiDE
SYmPTOm
CAUSe (AND RemeDY)
•
•
Ensure the AC power cord is connected.
The unit is not turned on.
No power.
•
Remove any obstacles between the remote control and
the unit.
•
•
Use the remote control near the unit.
Point the remote control at the remote sensor on the
The remote control does not function.
unit.
•
Replace all batteries in the remote control with new
ones.
•
•
Make sure that you’ve selected DVD mode.
The system is in pause mode. Press the PLAy button
to return to normal play mode.
•
•
•
Fast forward or fast reverse is performed. Press the
PLAy button to return to normal play mode.
The DTS DVD cannot be decoded to have speaker
output.
This unit is too hot. Shut off the unit for 30 minutes to
allow it to cool down.
DVD
No sound or only a very low-level sound is heard.
•
The region number of the disc doesn’t match the region
number of this unit.
No picture
•
•
Clean the disc.
The disc is scratched.
The picture is not clear
Severe hum or noise is heard.
•
•
Clean the disc.
There is no disc inside (“No Disc” appears on the
screen).
•
Insert the disc correctly with the label side facing up on
the disc tray.
•
•
Clean the disc.
A non-NTSC disc has been inserted. The unit and disc
region number are incompatible.
The disc does not play.
•
Condensation may have formed inside the unit due to a
sudden change in temperature. Wait about an hour for
it to clear and try again.
TV
Snowy picture, multiple image, picture distorted,
picture blurred and noisy sound.
•
•
Check antenna location, direction or connection.
Check the PICTURE SETTING in the TV SETUP
MENU.
No color of picture.
•
•
•
•
•
•
•
Not plugged into AC outlet.
Make sure that you’ve selected TV mode.
Try a new channel to check for possible station trouble.
Make sure the antenna is connected to properly.
Increase the volume.
The antenna is broken.
Check for local interference.
No picture and sound.
Colored patches of picture.
•
•
Magnetic interference from unshielded equipment.
Turn OFF the unit for 30 minutes, then turn ON again.
30
RCA SPS36123 Eng IB W011.indd 31
8/18/2009 4:30:03 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MAiNTENANCE
Cleaning the Disc
A defective or soiled disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
•
•
•
•
Do NOT touch the surface of the unlabeled side of the disc.
Do NOT stick paper or tape on the surface.
Do NOT expose the disc to direct sunlight or excessive heat.
Clean the disc before playback.Wipe the disc from the center outward
with a cleaning cloth.
•
•
NEVER use solvents such as benzine or alcohol to clean the disc.
Do NOT use irregular shaped discs (example:heart shaped, octagonal,
etc.). They may cause malfunctions.
Cleaning the Unit
Clean plastic cover over screen if it becomes dirty with oil, grease, dust, etc while cooking. Please follow
below steps.
•
•
Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit.
Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been
dipped in a weak soap-and-water solution and wrung out thoroughly. Then wipe with a dry cloth.
•
Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to
remove dust.
Important Note
Before transporting the unit, remove the disc from the disc compartment.
SPECifiCATiONS
Power source:
AC 120V ~ 60Hz
Specifications and external appearance are subject to change without notice.
Printed in China
811-391591W011
31
RCA SPS36123 Eng IB W011.indd 32
8/18/2009 4:30:03 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|