Amplified Indoor ·Outdoor Antenna
VHF · UHF
10 dB Amplification
fixed 10 dB amplification
for improved reception of
weak signals
Paintable
customize your antenna
color to match your interior
or exterior décor
Versatile
install your antenna indoors
or out, just about anywhere
TERRESTRIAL
HDTV
BROADCAST COMPATIBLE
Limited One-DYoewanrloWadafrroramnWtyww.Somanuals.com. All Manuals Search And Download.
ANT711
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ANT711 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Important Antenna Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Pre-installation Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ANT711 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Mounting the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Lightning Protection for Exterior Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connecting the Antenna to Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Coaxial Cable Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Limited One-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
Many do-it-yourself and professional antenna installers are injured or killed each year by electric
shock. While anyone can see the obvious danger of falling from a ladder, the most resourceful people
sometimes fail to recognize overhead wires as being potentially lethal. Touching any part of the
antenna mast or guy wire to these overhead wires results in the same shock you would receive if you
touched these wires directly with your bare hands. A very serious shock is almost sure to result when
contacting an electrical wire and, in the case of primary wires on the top of poles, the shock is similar
to being struck by a bolt of lightning. Many power wires are within 20 to 25 feet of the ground and
could easily be touched by an assembled antenna and mast.
ANT711 Amplified Indoor · Outdoor Antenna
VHF · UHF
Congratulations on your purchase of the ANT711 Amplified Indoor · Outdoor Antenna by RCA. This
antenna makes bulky, unmanageable antennas a thing of the past. The ANT711 not only provides great
reception, its new streamlined design is so attractive, you can use it just about anywhere inside and out.
The ANT711 can be installed on your rooftop, under your eaves, in your attic, outside an apartment
window, or on a wall above your TV. It’s lightweight, compact and HDTV ready. And, because the
ANT711 is paintable, it can match either its interior or exterior setting.
Please read and follow these important safety precautions.
• Be sure to select an antenna site well away from all overhead wires.
• Do not try to determine which overhead wires carry high voltage. Check with the power company.
• If you notice anything making contact with the overhead wires, call the power company to have it
removed safely.
ANT711 Features
• Do not run the downlead cable over power wires.
• Obtain help from a qualified professional when removing the old antenna if there is any doubt
clearing overhead wires.
The ANT711 Amplified Indoor · Outdoor Antenna is packed with features that make it as
functional as it is attractive.
• Never install an antenna by yourself. Be sure to have at least two people available for help.
• Never install the antenna when it is windy.
• VHF/UHF/HDTV Antenna
• Built-in amplifier
• Be sure to do all assembly work on the ground; then raise the antenna.
• Make sure the antenna mast downlead cable is connected to a suitable lightning arrester.
• Use 8 (or larger) AWG ground wire between the mast and the ground.
• Make sure the installation is secure with the use of guy wires or other mounting hardware.
• 10 dB average gain
• Paintable housing
• Multiple mounting methods, indoor or outdoors
• Easy to mount and install
• If you lose your grip on the antenna, let it fall to the ground. Do not attempt to catch it as it may touch
power lines as it falls.
• Terrestrial HDTV ready
• Lightweight and compact
• CALL THE POWER COMPANY TO REMOVE THE ANTENNA IF IT FALLS AND TOUCHES
POWER LINES. DO NOT ATTEMPT TO REMOVE IT YOURSELF.
• Integrated cable track and recessed coax cable
• Integrated diplexer for ultimate performance
Important Antenna Notes
WARNING! Use EXTREME CAUTION when installing an outdoor antenna close to overhead
wires. If any part of the antenna makes contact with overhead power lines, touching the antenna,
masting, cable or guy wires can cause electrocution and death.
The ANT711 antenna system is designed to work properly when the power injector is connected to the
antenna through a 75-ohm coaxial cable, such as RG6 or RG59.
The power injector has an indicator light to point out that
• DC power is being supplied to the antenna.
• There are no shorts in the connection between the power injector and antenna.
The coaxial cable between the power injector and the antenna is used for
• Carrying DC power from the power injector to the amplifier board in the antenna.
Before You Begin
Please read the Important Safety Precautions (page 4) prior to installation. For your safety and
convenience, plan each step of the installation and purchase the necessary hardware in advance.
The hardware required and the order in which you perform the steps depend on the mounting
and connection method you choose. If mounting on a mast, we recommend two people
assemble the entire antenna on the ground. Then mount the assembled antenna on the mast
for easier installation.
• Carrying the amplified TV signal from the antenna through the power injector to the
video equipment.
If any devices are used in your home cabling system, such as amplifiers, splitters, combiners,
matching transformers or 300-ohm cable, they must be connected only between the power injector and
your video equipment. Any devices connected between the power injector and the antenna might cause
a short in the amplifier power source. If this happens, the injector's indicator will not light and the signals
to your video equipment (multiple TVs or VCRs) may be significantly degraded.
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-installation Test
Mounting the Antenna (Continued)
Perform this test before installing your antenna to ensure that the unit is working properly.
Exterior or Attic Mounting To a Mast
Place both 1/4-20 bolts through the holes in the mast bracket. Thread into the back of the antenna.
Slide the bracket over the top of the mast and tighten bolts to secure. (To prevent damage to the
antenna, do not over tighten the bolts.) Raise the mast and secure it at the desired location. Then,
connect the cable.
1. Connect a temporary 75-ohm cable between the power injector's F-connector and the
antenna’s F-connector.
NOTE: If installing new lead-in cable, use the actual cable to be used in the installation.
2. Connect the power injector’s TV cable to your TV’s VHF/UHF 75-ohm F-connector.
3. Insert the supplied AC adapter’s small plug into the DC 12V jack on the power injector.
Lightning Protection for Exterior Mounting
4. Plug the supplied AC adapter into a standard AC outlet. If the power injector’s indicator lights up,
the antenna is properly working.
• Mount a grounding block (not supplied) as close as possible to the point where the downlead enters
the house.
5. Hold the antenna as close as possible to the area where it is to be mounted to check
TV reception.
• The downlead wire from the antenna to the grounding block and the mast ground wire should be
secured to the house with stand-off insulators, spaced four to six feet apart.
NOTE: Reception may change if mounted in a different location than the testing site.
• For a “ground-up” antenna installation, you may not need to ground the mast if it extends four or
more feet into the earth.
Connecting the Antenna to Your TV
To connect the antenna to your TV, follow these steps:
1. Connect the coax downlead from the antenna to the ANT jack on the power injector.
2. If your TV has an F-connector, connect the short coaxial cable on the power injector to your TV’s
VHF/UHF 75-ohm F-connector.
If your TV has screw terminals for the VHF/UHF connection, connect a 75-ohm to a 300-ohm
transformer (not supplied) between the power injector and the VHF/UHF terminals.
If your TV has a 75-ohm VHF connection and a 300-ohm UHF connection, connect a signal
splitter (not supplied) between the power injector and the TV’s VHF/UHF connections.
ANT711 Hardware
The ANT711 antenna package includes the following items:
3. Insert the supplied AC adapter’s small plug into the power injector’s DC 12V jack. Then plug the
adapter into a standard 120V AC outlet. The LED on the power injector lights to indicate that the
antenna is properly connected.
• ANT711 Antenna (1)
• Screws, #10 x 3", SS Phillips pan head (2)
• Mounting spacers (2)
• Power injector (1)
• AC adapter (1)
• Mast bracket (1)
Coaxial Cable Installation Precautions
• Adjustable wall mounting brackets (2)
• Screws, #8 x 1-1/2", SS Phillips pan head (4)
• Bolts, 1/4-20 x 1-1/2 SS hex head (2)
• Coaxial cable, 6ft RG6 (1)
• Do not bend the coaxial cable into less than a three-inch radius. Tighter bends can cause shorts and
can change the cable’s impedance.
Mounting the Antenna
• Do not install the coaxial cable where it will have a pulling tension greater than 15 pounds during
installation. After installation, make sure there is no tension on the cable.
Interior or Exterior Mounting To a Wall Using the Adjustable Wall Brackets
• Use only round-headed staples. Any clamps or securing devices used with coax should grip the cable
evenly about the circumference without crushing the cable. Flat staples can damage the coaxial cable.
Determine the desired mounting location. Attach the adjustable brackets, and mark the wall to indicate
mounting location. Attach the brackets by placing them into the slots on the rear of the antenna at the
desired location. Turn counter-clockwise to tighten brackets. Attach one end of the coaxial cable to the
rear F-connector of the antenna. Secure the antenna to the wall using the #8 x 1 1/2" self-tapping screws.
• Do not expose the coaxial cable to a temperature greater than 176 degrees Fahrenheit. Keep the cable
away from heating vents and water heaters.
Interior or Exterior Mounting To a Wall Using the Spacers
• The cable jacket withstands most outdoor environments. However, you must seal the connections
and splices against water entry.
Determine the desired mounting location. Mark the wall to indicate placement of antenna. Attach one
end of the coaxial cable to the rear F-connector of the antenna. Secure the antenna to the wall using the
#10 x 3" screws and spacers.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Dimensions: 46.9"w x 5.75"h x 3"d
Operational bandwidth: VHF @ 54-88, 174-216MHz, UHF @ 470-806MHz
FM trap: Fixed @ 88-108MHz
Amplifier gain: 10 dB Average
Output impedance: 75 Ohms
Power requirement: 12V DC/120V AC, 60Hz (with supplied adapter)
Weather resistance: amplifier is conformal coated
Limited One-Year Warranty
THOMSON INC. warrants that, for one year from date of purchase, it will replace this product
if found to be defective in materials or workmanship. Return it postage paid to the Product
Exchange Center, 11721 Alameda Ave., Socorro, TX 79927 for prompt, no-charge replacement with
a current equivalent. This replacement is THOMSON INC.’s sole obligation under this warranty.
THOMSON INC. will not be responsible for any incidental or consequential damages or for any
loss arising in connection with the use or inability to use this product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty excludes defects or damages due to misuse, abuse, or neglect.
This warranty gives you specific legal rights, and you may also have other rights, which vary from
state to state.
© 2003 THOMSON INC.
10330 N. Meridian Street,
Indianapolis, IN 46290
Trademark(s) ® Registered
Marca(s) Registrada(s)
www.rca.com
All other brands and product names
are trademarks or registered trademarks
of their respective owners.
Product specifications subject to change.
Download from Www.Somanuals.com. All Manuals Search And Download.
|