Concert Stage Monitor
Loudspeaker User Manual
CSM10 – 10" Full-range loudspeaker
CSM12 – 12" Full-range loudspeaker
CSM15 – 15" Full-range loudspeaker
TD-000279-00-A
*TD-000279-00*
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty (USA only; other countries, see your dealer or distributor)
Disclaimer
QSC Audio Products, LLC is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and/
or use of this loudspeaker product.
QSC Audio Products 3-Year Limited Warranty
QSC Audio Products, LLC (”QSC”) guarantees its products to be free from defective material and/or workmanship and will replace defective parts and
repair malfunctioning products under this warranty when the defect occurs under normal installation and use-provided the unit is returned to our factory,
one of our authorized service stations or an authorized QSC International Distributor via pre-paid transportation with a copy of proof of purchase (i.e.,
sales receipt). This warranty provides that the examination of the return product must indicate, in our judgment, a manufacturing defect. This warranty
does not extend to any product which has been subjected to misuse, neglect, accident, improper installation, or where the date code has been removed
or defaced. QSC shall not be liable for incidental and/or consequential damages. This warranty gives you specific legal rights. This limited warranty is
freely transferable during the term of the warranty period. The warranty on QSC products is NOT VALID if the products have been purchased from an
unauthorized dealer/online e-tailer, or if the original factory serial number has been removed, defaced, or replaced in any way. Damage to, or loss of any
software or data residing on the product is not covered. When providing repair or replacement service, QSC will use reasonable efforts to reinstall the
product’s original software configuration and subsequent update releases, but will not provide any recovery or transfer of software or data contained on
the serviced unit not originally included in the product.
Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is
void, prohibited or superseded by local laws, the remaining provisions shall remain in effect.
The QSC limited warranty is valid for a period of three (3) years from date of purchase in the United States and many (but not all)
other countries.
For QSC warranty information in countries other than the United States, contact your authorized QSC international distributor. A list of QSC International
swered by calling, e-mailing or contacting your authorized QSC distributor.
© 2009, QSC Audio Products, LLC.
Patents may apply or be pending.
QSC is a registered trademark of QSC Audio Products, LLC.
“QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office.
All trademarks are the property of their respective owners.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The CSM Series of stage monitors is a very low profile, high output wedge speaker that provides the highest output to size ratio of any premium
brand. These high performance speakers use a high power, 3" neodymium magnet compression driver, coupled with a 4" voice coil woofer on the
CSM12 and CSM15 and a 3" voice coil woofer on the CSM10. The CSM series features a selectable pattern control “shutter” system that by opening
the shutter, converts the vertical coverage to an asymmetrical pattern of +45° and -75° relative to the baffle, while maintaining a nominal 50° pattern
in the horizontal. As a result, the user is able to limit the amount of sonic HF energy spilling over into the audience, while increasing its upstage
coverage angle.
In addition, the CSM Series features integral hardware that provides up to an additional 15° (in 1° increments) of angle to the enclosure as well as a
recessed connector pocket that allows the user to dress the cable a full 360° in any direction.
Signal Processing
The CSM Series is designed as a “Best in Class” stage monitor system package. The amazing performance of the CSM models is a result of extensive
and sophisticated application of digital signal processing. The algorithms have been developed using QSC processing products and can not be readily
replicated on other DSP platforms. In order to enjoy all the performance that your QSC CSM speakers can deliver, it is important to use the correct
to “Technical Support” - “Software Downloads” to obtain the correct settings for your monitor model, QSC processor and application. Note that
application specific settings for full-range, bi-amp, stage monitor and utility applications are available.
QSC will, from time to time introduce new digital signal processing platforms so check the “CSM Series” section of the QSC website for the latest
processor recommendations.
Power
In order to take full advantage of CSM Series capabilities abundant and clean amplifier power is required. Recommended amplifiers and power levels:
CSM10
•
•
LF amplifier: QSC PL340 or other amplifier capable of at least 800 W @ 8Ω; 1250 W @ 4Ω & 2000 W @ 2Ω.
HF amplifier: QSC PL325 or other amplifier capable of at least 500 W @ 8Ω; 850 W @ 4Ω & 1250 W @ 2Ω.
CSM12 and CSM15
•
•
LF amplifier: QSC PL380 or other amplifier capable of at least 1500 W @ 8Ω; 2500 W @ 4Ω & 4000 W @ 2Ω.
HF amplifier: QSC PL325 or other amplifier capable of at least 500 W @ 8Ω; 850 W @ 4Ω & 1250 W @ 2Ω.
CSM Loudspeaker
1. Grille
5
6
2
2. Deco Plate
1
7
3. Shutter Switch
3
4. M10 Yoke and Suspension
Points (QTY:12)
8
5. Handle
6. Hard Rubber Feet
7. Full-Range/Bi-amp Switch
8. Input Plate
4
9. Tilt Release Mechanism
10. Skids
5
10
9
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Coverage Pattern
On the side of the speaker you will find the shutter switch which will
allow the lip extension to be engaged in either an Asymmetric (ASYM) or
Symmetric (SYM) configuration. (Figure 1)
To select coverage pattern, insert a standard flat blade screw driver into
the slot provided and push to release shutter. Turn clockwise a quarter
turn to change from SYM to ASYM. Turn counterclockwise a quarter turn
for ASYM to SYM.
In monitor position, symmetric coverage will allow for 150° vertical
coverage, 50° horizontal coverage. Asymmetric coverage will allow for 120°
vertical coverage, 75° down and 45° up, with a 50° horizontal coverage.
In utility position (side oriented), symmetric coverage is 150° horizontal
coverage, 50° vertical coverage. Asymmetric coverage is 120° horizontal
coverage, 50° degree vertical coverage.
– Figure 1 –
NOTE: Shutter actuator must be fully depressed or shutter will not engage and turn.
NOTE: Shutter should move smoothly if fully engaged. Do not use excessive force or non-standard screw driver when activating
shutter actuator button.
NOTE: Speaker will come from the factory engaged in ASYM position.
Adjusting Tilt Mechanism
Located in the rear bottom side of the speaker you will find the Tilt
Mechanism. (Figure 2)
To activate the tilt mechanism, insert fingertips underneath the enclosure,
locate the grab bar and pull bar towards you to release the mechanism. Lift
speaker to desired height and release grab bar. This will lock the legs into
the desired angle.
To disengage tilt mechanism, insert fingertips underneath the enclosure and
pull grab bar toward you lifting slightly to disengage teeth.
– Figure 2 –
While supporting the weight of the speaker slowly lower to the desired angle.
NOTE: Make sure the teeth are fully seated at the desired angle and locked evenly before leaving unattended.
NOTE: Do not grab legs or any other surface of box while raising or lowering.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Connections
The input connector for the CSM is mounted on the bottom side of the enclosure. To gain access to the connectors use the front handle to tilt the
speaker onto the skids located on the flat back side allowing full access to the recessed connector pocket and mode selection switch.
MODE Selection Switch
Mode Selection Switch
Located on the input plate housing is the Mode selection switch (Figure 3). This will
allow the speaker to go from bi-amp to full-range.
BI AMP
FULL RANGE
To select the mode, orient speaker so the back side is facing you. Insert a standard flat
screwdriver into available slot and slide left for full-range and right for bi-amp.
– Figure 3 –
NOTE: Speaker will come from the factory in bi-amp setting.
Input Connectors
The CSM input/output connectors are a pair of Neutrik NL4’s wired in parallel which allows for multi speaker mixes. See (Table 1) for bi-amp
connection. See (Table 2) for full-range connection.
Table 1: Bi-amp Connector Pinout
PIN
1+
1-
Connection
Low-frequency Transducer + (8 Ohms)
Low-frequency Transducer - (8 Ohms)
High-frequency Transducer + (8 Ohms)
High-frequency Transducer + (8 Ohms)
2+
2-
Table 2: Full-Range Connector Pinout
PIN
1+
1-
Connection
Full-range
Full-range
Thru
2+
2-
Thru
Pinout Table as printed on CSM input plate label
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications | Dimensions
CSM10
CSM12
CSM15
Configuration
2-way wedge
2-way wedge
2-way wedge
Transducers
Low-frequency
10"/3" voice coil woofer
3" diaphragm/1.4 exit
80 Hz – 20 kHz
12"/4" voice coil woofer
3” diaphragm/1.4 exit
65 Hz – 20 kHz
15"/4" voice coil woofer
3” diaphragm/1.4 exit
55 Hz – 20 kHz
High-frequency
Frequency Response ( 3 dB)
Frequency Range (-10 dB)
Nominal Coverage (-6 dB)
Wedge
70 Hz – 20 kHz
55 Hz – 20 kHz
45 Hz – 20 kHz
50° H x +45°/-75° V
150° H x 50° V
50° H x +45°/-75° V
150° H x 50° V
50° H x +45°/-75° V
150° H x 50° V
Multipurpose
Power Handling (Continuous)
Passive
450W
450W
110W
550W
550W
110W
650W
650W
110W
Low-frequency
High-frequency
Sensitivity (SPL 1 W at 1 m)
Passive
95 dB
97.5 dB
98.5 dB
108 dB
96.5 dB
97 dB
Low-frequency
96 dB
High-frequency
Max Calculated Output (SPL at 1 m)
Passive
108.5 dB
108.5 dB
127 dB
130.5 dB
130.6 dB
Low-frequency
128 dB
131.5 dB
131.1 dB
High-frequency
Cabinet Type
134.9 dB
134.9 dB
134.9 dB
Ported wedge
Ported wedge
Ported wedge
Enclosure
15 mm Birch plywood
Heavy-duty, powder coated steel
11.87” x 14.7” x 24”
(301.5 mm x 373.4 mm x 310.6 mm)
15 mm Birch plywood
Heavy-duty, powder coated steel
11.87” x 19.7” x 24”
(301.5 mm x 500 mm x 610.6 mm)
15 mm Birch plywood
Heavy-duty, powder coated steel
12.87” x 21.7” x 26”
(326.9 mm x 551 mm x 662 mm)
89 lb / 40.3 kg
Grille
Dimensions (HWD)
Weight (Net)
60 lb / 27.2 kg
79 lb / 35.8 kg
Optional Attachment
Yoke/pole mount
Yoke/pole mount
Yoke/pole mount
CSM10
24"
14.7"
373 mm
Side
with
610 mm
Angle
15.3"
389 mm
15°
12.1"
307 mm
Side
Top
Front
CSM12
Side
with
19.7"
500 mm
24"
610 mm
Angle
15.3"
12.1"
389 mm
307 mm
15°
Side
Top
Front
CSM15
26.1"
663 mm
Side
with
21.7"
551 mm
Angle
16.9"
429 mm
13.1"
333 mm
15°
Side
Top
Front
Specifications subject to change without notice.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Mailing Address:
QSC Audio Products, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626-1468 USA
Telephone Numbers:
Main Number: (714) 754-6175
Sales & Marketing: (714) 957-7100 or toll free (USA only) (800) 854-4079
Customer Service: (714) 957-7150 or toll free (USA only) (800) 772-2834
Facsimile Numbers:
Sales & Marketing FAX: (714) 754-6174
Customer Service FAX: (714) 754-6173
World Wide Web:
E-mail:
© 2009 QSC Audio Products, LLC. All rights reserved. QSC, and the QSC logo are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries.
Neutrik is a trademark of Neutrik. All other trademarks are the property of their respective owners. Patents may apply or be pending.
Download from Www.Somanuals.com. All Manuals Search And Download.
|