P Z R 3 0 0 0
A m p l i f i e r
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL, PZR3000
Stereo/Mono Switch
Lets you select conventional
stereo operation with a
stereo input signal or bridged
mono input mode.
Fan Cooling
Input Jacks
Cooling system is automatically activated
whenever amplifier is turned on. This forced
air cooling system rapidly exhausts interior
heat, reducing operating temperature and
aiding performance.
Let you connect a variety of audio
input sources via the balanced
(XLR/6.35mm phone jack
combinations) or unbalanced (RCA)
inputs.
PYLE PRO PZR3000 Amplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
1
INSTALLATION GUIDELINES
Stereo or Mono Inputs
Your Pyle Pro amplifier can be operated in Stereo, Mono or
Bridged mode, depending on the input source. If the input
signal is mono, slide the Stereo/Mono/Bridged selector
switch to MONO and the signal will be routed through both
channels. If you wish to run the amplifier in bridged output
mode, slide the switch to Bridged.
Connecting the GND (Ground) screw terminal
Connecting a mixer or preamplifier may cause excessive
noise or hum in the amplifier output. To prevent this,
connect one end of a low-capacitance shielded wire to the
amplifier’s ground screw (on the rear panel). Then connect
the other end of this wire to the ground terminal on the
mixer or preamplifier enclosure.
Speaker connections
PREAMP OR MIXER
You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to
Channel 1 and/or Channel 2 of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
GROUND
SCREW
LOW CAPACITANCE SHIELDED WIRE
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
Input connections
These amplifiers accept a broad range of input sources,
including Compact Disc (CD) players; DVD, Cassette, Reel-
to-Reel or other tape players; Radio Tuners; Equalizers;
Signal Processors.
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of the speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
Connecting a CD or DVD or tape player or tuner
In a normal installation, one would use the RCA JACKS for
connecting a CD player, DVD, tape player or tuner.
2. Connect the speaker wires to the speaker's positive and
negative terminals.
CD PLAYER, DVD , TAPE PLAYER
OR TUNER
use RCA jacks
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
Connecting an equalizer or external signal processor
Connect the processor’s OUT to the amplifier’s INPUT
connectors.
STEREO OPERATION
SWITCH IN “STEREO” POSITION
EQ OR MIXER
CH 2
CH 1
-OR–
STEREO SIGNAL SOURCE
EQ OR MIXER
use XLR/6.35 mm
combo jacks
2 – PYLE PRO PZR3000 Amplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to standard AC power
MONO OPERATION
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
SWITCH IN “MONO” POSITION
Mounting the amplifier
This amplifier is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
CH 2
CH 1
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
Turning the amplifier on
1. Turn on the audio input source equipment which is
connected to the amplifier INPUT jacks.
MONO SIGNAL SOURCE
2. Set the amplifier’s Channel 1 and Channel 2 output level
gain controls to the minimum level settings.
USE
CHANNEL 1
INPUT ONLY
3. Push in the power switch to turn the amplifier on.
Using the power blue LED meters
The meter pointer position indicates the amplifier output
power. For ease of reading in dark environments, the meter
is illuminated.
Bridged Mode Operation
This amplifier can operate in a mono bridged output mode, if
your speakers can handle the following power output levels:
PZR3000:
3000 watts
Using the Channel 1 and Channel 2 Output Level controls
Rotate output level gain clockwise to increase, or counter-
clockwise to decrease the output power. To get the best
performance with the least sound distortion, always adjust
the output level gain so the meter's pointer does not
continuously exceed the extreme right of the meter's scale.
As shown in the diagram below, connect the speaker's positive
(+) to the amplifier's red speakers left (1/2) terminals and
negative (-) to red speakers right (1/2) terminals.
The speaker right (+) on the amplifier is used as a negative (-)
terminal for a bridged connection.
About the internal clip circuitry
Special clip circuitry incorporated into your Pyle Pro
amplifier’s design protects the amplifier and speaker system
from being damaged from overdriving power.
MONO BRIDGED OPERATION
SWITCH IN “BRIDGED” POSITION
Under normal conditions, the amplifier’s clip indicator will
flicker as the output power momentarily exceeds the level
as set by the output level gain selector.
However, under excessive output conditions, the clip
indicator lights remain on continuously, alerting you that
the special clip circuitry has become active. When this
occurs, you should simply reduce the output power level
by rotating the Master Volume control counterclockwise.
USE
CHANNEL A
INPUT ONLY
MONO SIGNAL SOURCE
PYLE PRO PZR3000 Amplifier
- 3
Caring for your Pyle Pro Amplifier
Limited Warranty
Your Pyle Pro Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier gently and carefully - do not drop!
• Keep the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking
new. Do not use harsh chemicals, solvents or
detergents!
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
Resetting the circuit breaker
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
•
•
A copy of your sales receipt or other proof of purchase
A brief letter, indicating the problem you are experiencing with the
product
Include in your letter your return address, daytime phone number and
R.A. number
Also include a check or money order for $20.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Resetting the circuit breaker
•
•
This amplifier employs a circuit breaker for protection from
power surges and short circuits. If the amplifier suddenly
turns off or will not turn on, check the circuit breaker. If
it is tripped, check and correct for a short or overload
condition. Wait for the amplifier to cool, then press the
circuit breaker RESET button on the back of the amplifier.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
Amplifier Specifications
PZR3000
Input Impedance, balanced (unbalanced)
20 k-Ohms (10 k-Ohms)
Continuous Output Power
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
200W x 2
300W x 2
230W x 2
320W x 2
1500W x 2
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
Peak Power, 8 Ohms
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 8 Ohms
600W x 1
600W x 1
3000W x 1
Peak Power
THD at rated output power
0.1%
10 Hz to 50 kHz
1.0V
Frequency Response +/– 3 dB
Input Sensitivity for rated output power
Signal-to-Noise Ratio A-Weighted
100 dB
Speaker Impedance
Stereo
Bridged
4-16 Ohms
8-16 Ohms
Power Requirement
120 VAC, 60 Hz
Dimensions H x W x D, inches
(mm)
5 3/16 x 19 x 15 3/8
(132 x 482 x 390)
Weight, lbs (kg)
31.9 Ibs (14.5)
4 – PYLE PRO PZR3000 Amplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
PYLE PRO PZR3000 Amplifier
- 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|