Model No. 831.24745.3
Serial No.
TREADMILL EXERCISER
Write the serial number in the
space above for future reference.
User’s Manual
Serial
Number
Decal
• Assembly
• Operation
• Maintenance
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. Sears as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over the age of 35 or persons
with pre-existing health problems.
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local Sears store or call the telephone
number on the back cover of this manual and
order part number 146148, or see your local
electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 19 if the treadmill is
not working properly.)
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons 16. Read, understand, and test the emergency
weighing 300 lbs. (136 kg) or less.
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. When connecting the power cord (see page
11), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
24. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 18.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
XP 615 TRAINER treadmill. The XP 615 TRAINER
treadmill offers an impressive array of features de-
signed to make your workouts at home more enjoyable
and effective. And when you’re not exercising, the
unique XP 615 TRAINER treadmill can be folded up,
requiring less than half the floor space of other tread-
mills.
ing this manual, call 1-800-4-MY-HOME® (1-800-469-
4663).To help us assist you, please note the product
model number and serial number before contacting us.
The model number and the location of the serial num-
ber decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Book Holder
Console
Accessory Tray
Handrail
Pulse Sensor
Key/Clip
Upright
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Make sure that the power cord is unplugged. Assembly requires two persons. Set the treadmill in a cleared
area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note:
The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small
amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal con-
dition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the
lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
adjustable wrench
and
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one
of the parts to be assembled. Extra hardware may be included. If a part is missing, call 1-888-533-1333. To
avoid damaging plastic parts, do not use power tools for assembly.
3/4" Screw (10)–5
3/8" Star
Washer (9)–4
5/16" Star
Washer (7)–4
3/8" Nut (8)–2
Base Pad Spacer
(25)–2
1" Tek Screw (56)–4
5/16" x 1" Bolt (5)–4
3/8" x 2" Bolt (4)–2
3/8" x 4" Bolt (6)–4
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (53) so that the treadmill is more stable;
do not fully fold the Frame yet.
1
B
A
78
Hole
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
80
53
79
Cut the tie securing the Upright Wire (78) to the
Base (80). Locate the tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
56
Tie
Attach a Base Pad (79) to the Base (80) in the
location shown with a Base Pad Spacer (25) and
a 1" Tek Screw (56). Then, attach another Base
Pad (79) with only a 1" Tek Screw (56).
25
79
56
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (80).
Attach a Base Wheel (81) with the Bolt and the
Nut that you just removed. Do not overtighten
the Nut; the Wheel must turn freely. Discard
the shipping bracket.
2
Tie
78
80
4
Cut the tie off the Upright Wire (78).
81
C
8
3. Identify the Right Upright (72) and the Right
Upright Spacer (74), which are marked with
stickers. Insert the Upright Wire (78) through the
Right Upright Spacer as shown.
3
Tie
72
See the inset drawing. Tie the wire tie in the
Right Upright (72) securely around the end of
the Upright Wire (78). With the help of a second
person, hold the Right Upright near the Base
(80). Then, pull the other end of the wire tie until
the Upright Wire is routed completely through
the Right Upright.
78
78
74
80
72
Wire
Tie
78
4
4. Hold a Bolt Spacer (3) inside the lower end of
the Right Upright (72). Insert a 3/8" x 4" Bolt (6)
with a 3/8" Star Washer (9) into the Right
Upright and the Bolt Spacer. Repeat this step
with a second Bolt Spacer (3), 3/8" x 4" Bolt (6),
and Star Washer (9).
6
72
9
78
3
Hold the Right Upright Spacer (74) and the
Right Upright (72) against the Base (80). Be
careful not to pinch the Upright Wire (78).
Finger tighten the 3/8" x 4" Bolt (6); do not fully
tighten the Bolts yet.
80
3
75
74
Press a Base Endcap (75) into the Base (80).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (53) so the treadmill is more stable; do
not fully fold the Frame yet.
5
A
B
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
80
79
53
Attach a Base Pad (79) to the Base (80) in the
location shown with a Base Pad Spacer (25)
and an 1" Tek Screw (56). Then, attach another
Base Pad (79) with only a 1" Tek Screw (56).
4
56
25
Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4),
and the shipping bracket (C) from the Base (80).
Attach a Wheel (81) with the Bolt and the Nut
that you just removed. Do not overtighten the
Nut; the Wheel must turn freely. Discard the
shipping bracket.
81
79
56
C
8
6. With the help of a second person, hold a Bolt
Spacer (3) inside the lower end of the Left
Upright (71). Insert a 3/8" x 2" Bolt (6) with a
3/8" Star Washer (9) into the Left Upright and
the Bolt Spacer. Repeat this step with a second
Bolt Spacer (3), 3/8" x 2" Bolt (6), and 3/8" Star
Washer (9).
6
6
71
73
9
3
3
Orient the Left Upright (71) and the Left Upright
Spacer (73) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(80). Finger tighten the 3/8" x 2" Bolts (6); do
not fully tighten the Bolts yet.
75
80
Press a Base Endcap (75) into the Base (80).
With the help of a second person, tip the tread-
mill so that the Base (80) is flat on the floor.
7. Have a second person hold the console assem-
bly near the Right Upright (72). Remove the wire
tie from the Upright Wire (78).
7
Connect the Upright Wire (78) to the console
wire. The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF THE CON-
NECTORS ARE NOT CONNECTED PROP-
ERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON. Then, in-
sert the connectors into the Right Upright (72).
Console
Wire
Console
Assembly
78
7
5
Set the console assembly on the Right Upright
(72) and the Left Upright (not shown). Attach the
console assembly with four 5/16" x 1" Bolts (5)
and four 5/16" Star Washers (7); start all four
Bolts and then tighten them.
7
78
72
5
Wire Tie
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Insert the Book Rack (84) into the console as-
sembly; it may be helpful to rock the Book Rack
up and down as you insert it. Attach the Book
Rack with five 3/4" Screws (10); start all five
Screws and then tighten them.
8
84
Console Assembly
See steps 4 and 6. Tighten the 3/8" x 4" Bolts
(6).
10
10
10
9. If necessary, press the Left Tray (86) and the
Right Tray (85) into the top of the console as-
sembly.
9
86
Console
Assembly
85
10. Identify the Latch Assembly (55). Remove the
tie from the end of the tube. Make sure that the
sleeve has been slid over hole 1 and that the
Latch Knob (54) is locked into hole 1. Pull on
the sleeve to make sure that it is locked into
place.
10
54
Hole 1
55
Tube
Sleeve
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Raise the Frame (53) to the position shown.
Have a second person hold the Frame until
this step is completed.
11
53
Orient the Latch Assembly (55) so that the large
barrel and the Latch Knob (54) are in the posi-
tions shown. Attach the lower end of the Latch
Assembly to the bracket on the Base (80) with a
3/8" x 2" Bolt (4) and a 3/8" Nut (8).
8
4
55
54
Attach the upper end of the Latch Assembly
(55) to the bracket on the Frame (53) with a 3/8"
x 2" Bolt (4) and a 3/8" Nut (8). Note: It may be
necessary to move the Frame back and forth to
align the Latch Assembly with the bracket.
Large
Barrel
80
Lower the Frame (53) (see HOW TO LOWER
THE TREADMILL FOR USE on page 18).
8
4
12. Plug the indicated end of the power cord into
the socket on the front of the treadmill.
12
Socket
Power
Cord
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt (see
pages 20 and 21).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Grounding Pin
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local Sears store or call the telephone number
on the back cover of this manual and order part
number 146148, or see your local electronics store.
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Clip
Key
FEATURES OF THE CONSOLE
To use the manual mode of the console, follow the
steps beginning on page 13. To use a preset work-
out, see page 15.
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable.
Note: If there is a sheet of clear plastic on the console,
remove the plastic. To prevent damage to the walking
platform, wear clean athletic shoes while using the
treadmill. The first time the treadmill is used, observe
the alignment of the walking belt, and center the walk-
ing belt if necessary (see page 20).
When the manual mode of the console is selected, you
can change the speed and incline of the treadmill with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even mea-
sure your heart rate using the handgrip pulse sensor.
In addition, the console offers twelve preset workouts.
Each workout automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive exercise session.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
3. Start the walking belt.
To start the walking belt, press the Start button, the
Go button, the speed increase button, or one of the
speed buttons numbered 2 through 10.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
If the Start button, the Go button, or the speed in-
crease button is pressed, the walking belt will begin
to move at 1 mph. As you exercise, change the
speed of the walking belt as desired by pressing
the speed increase and decrease buttons. Each
time a button is pressed, the speed setting will
change by 0.1 mph; if a button is held down, the
speed setting will change in increments of 0.5 mph.
Note: After the buttons are pressed, it may take a
moment for the walking belt to reach the selected
speed setting.
Plug in the power cord (see
page 11). Next, locate the
Reset
reset/off circuit breaker on
the treadmill frame near the
power cord. Switch the cir-
cuit breaker to the reset po-
sition.
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
17 to turn off the demo mode.
If one of the numbered speed buttons is pressed,
the walking belt will gradually increase in speed until
it reaches the selected speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Go button, the speed increase button, or one of the
speed buttons numbered 2 through 10.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 12)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase and de-
crease buttons or one of
the numbered incline but-
tons. Each time you
press the incline increase or decrease button, the
incline will change by 0.5%. If you press one of the
numbered incline buttons, the treadmill will adjust
to the selected incline setting. Note: After you
press the buttons, it may take a moment for the
treadmill to reach the selected incline setting.
HOW TO USE THE MANUAL MODE
5. Monitor your progress with the matrix and the
displays.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER above.
2. Select the manual mode.
The matrix—When the
manual mode is selected,
the matrix will display a
1/4-mile track. As you ex-
ercise, the indicators
When the key is in-
serted, the manual
around the track will light
in succession until the
entire track is lit. The track will then darken and the
indicators will again begin to light in succession.
mode will be selected
and a track will appear
in the matrix. If a preset
workout has been
selected, remove the
key and then reinsert it.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Time display—When
6 . Measure your heart rate if desired.
the manual mode is se-
lected, this display will
show the elapsed time.
When a workout is se-
Before using the handgrip pulse sensor, first re-
move the sheets of clear plastic from the metal
contacts on the pulse bar. In addition, make sure
that your hands are clean.
lected, the display will
show the time remaining in the workout rather than
the elapsed time.
To use the hand-
grip pulse sen-
sor, stand on
the foot rails
and hold the
pulse bar with
your palms on
the metal con-
tacts. Avoid
moving your hands. When your pulse is detected,
two dashes (– –) will appear in the Calories/Pulse
display, and then your heart rate will be shown.
For the most accurate heart rate reading, con-
tinue to hold the contacts for about 15 sec-
onds.
Distance/Incline dis-
play—This display
shows the distance that
you have walked or run.
Note: Each time the in-
cline changes, the dis-
play will show the incline setting for several sec-
onds.
Contacts
Calories/Pulse
display—This display
shows the approximate
number of calories you
have burned. The dis-
play will also show your
heart rate when you use the handgrip pulse sen-
sor.
7. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
Speed display—This
display shows the
speed of the walking
belt.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical compo-
nents may wear prematurely.
which unit of measure-
ment is selected, see
THE INFORMATION MODE on page 17. Note:
For simplicity, all instructions in this manual
refer to miles.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A PRESET WORKOUT
1. Insert the key into the console.
incline setting are programmed for each segment.
Note: The same speed setting and/or incline set-
ting may be programmed for two or more consecu-
tive segments.
See HOW TO TURN ON THE POWER on
page 13.
During the workout, the
profile will show your
Current Segment
progress. The flashing
segment of the profile
represents the current
segment of the workout.
The height of the flashing
segment indicates the
speed setting for the cur-
2. Select a preset workout.
To select a preset workout, press the Select
Workout button repeatedly.
When a preset workout
is selected, the mini-
rent segment. At the end of each segment, a series
of tones will sound and the next segment of the pro-
file will begin to flash. If a different speed or incline
setting is programmed for the next segment, the
speed or incline setting will flash in the display to
alert you.
mum speed setting of
the workout will appear
in the Distance/Incline
display, the maximum
speed setting will ap-
pear in the Calories/Pulse display, and the workout
time will appear in the Time display. In addition, a
profile of the speed settings of the workout will
scroll across the matrix.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
3. Customize your workout if desired.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons. Note: When the next segment of the
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
You can change the length of the workout, the min-
imum speed setting of the workout, and/or the
maximum speed setting of the workout before you
begin. To customize your workout, press the Set
Time, the Set Min Speed, and/or the Set Max
Speed increase and decrease buttons. The new
workout settings will appear in the displays.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Go button. The walking belt will begin to
move at 1 mph. When the next segment of the
workout begins, the treadmill will automatically ad-
just to the speed and incline settings for the next
segment.
4. Press the Start button or the Go button to start
the workout.
A moment after the button is pressed, the treadmill
will automatically adjust to the first speed and in-
cline settings of the workout. Hold the handrails
and begin walking.
Each workout is divided into 30 one-minute seg-
ments, unless you have changed the length of the
program (see step 3). One speed setting and one
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Monitor your progress with the matrix and the
displays.
7. When you are finished exercising, remove the
key from the console.
See step 5 on pages 13 and 14.
6. Measure your heart rate if desired.
See step 6 on page 14.
See step 7 on page 14.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
The Time display will show
the total number of hours the
treadmill has been used.
The console features an information mode that keeps
track of the total distance that the walking belt has
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to switch the console from miles to kilometers. In addi-
tion, the information mode allows you to turn on and
turn off the display demo mode.
Note: The console features a display demo mode, de-
signed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the circuit breaker to the reset position, and in-
sert the key into the console. However, when you re-
move the key, the displays will remain lit, although the
buttons will not function. If the demo mode is turned on,
a “d” will appear in the Speed display while the informa-
tion mode is selected. To turn on or turn off the demo
mode, press the speed decrease button.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
An “E” for English miles or
an “M” for metric kilometers
will appear in the
Calories/Pulse display.
Press the speed increase
button to change the unit of
measurement if desired.
To exit the information mode, remove the key from the
console.
The Distance/Incline display
will show the total number of
miles (or kilometers) that the
walking belt has moved.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in
the storage position.
Frame
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° F (30° C).
Latch Knob
HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
knob is locked in the storage position.
Handrail
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheels
Base
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your left hand. Pull the latch knob to the left and hold it. It may be nec-
essary to push the frame forward as you pull the knob to the left. Pivot the frame downward and release the
latch knob.
2. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your legs and keep your back straight.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call the telephone number listed on
the back cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 11. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the back cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
a
THE POWER CORD. Remove the three 3/4"
10
Screws (10) and carefully pivot the Hood (57) off.
57
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate the Reed Switch (64) and the Magnet (42)
on the left side of the Pulley (43). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If neces-
sary, loosen the Reed Switch Screw (12), move the
Reed Switch slightly, and then retighten the Screw.
Reattach the Hood, and run the treadmill for a few
minutes to check for a correct speed reading.
1/8 in.
12
42
43
64
Top
View
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 17 to turn off the demo mode.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
rear roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
2–3 in.
Rear Roller Bolts
c. If the walking belt still slows when walked on, see the back cover of this manual.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left rear roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is centered.
a
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clock-
wise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side
of the walking belt 2 to 3 in. (5 to 7 cm) off the
walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert
the key, and carefully walk on the treadmill for a
few minutes. Repeat until the walking belt is prop-
erly tightened.
b
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over the age of 35 or persons with pre-exist-
ing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.24745.3
R0607A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
7
9
4
2
4
4
4
6
4
22
1
1
2
2
2
2
1
1
2
8
8
2
2
1
2
4
2
2
1
4
3
2
2
3
4
2
1
2
2
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1/2" Screw
3/4" Tek Screw
Bolt Spacer
3/8" x 2" Bolt
5/16" x 1" Bolt
3/8" x 4" Bolt
5/16" Star Washer
3/8" Nut
3/8" Star Washer
3/4" Screw
Latch Endcap
Reed Switch Screw
5/16" x 1 1/4" Bolt
5/16" x 3 5/8" Bolt
1" Lift Frame Bolt
Rear Roller Bolt
3/8" x 1 3/4" Bolt
3/8" x 1 1/2" Bolt
3/8" x 1" Bolt
1/2" Ground Screw
1 1/4" Screw
1/4" Motor Bolt
3/8" x 3/4" Bolt
3/8" x 4" Bolt
Base Pad Spacer
Belt Guide Screw
1/4" Flat Washer
1/4" Lock Washer
3/8" Star Washer
U-nut
3/8" Motor Pivot Nut
3/8" Motor Nut
5/16" Nut
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
*
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
4
1
2
2
7
1
1
1
1
1
1
1
1
1
1
1
1
1
3
2
–
–
–
–
–
–
–
–
–
1" Tek Screw
Hood
Lift Frame Ground Wire
Drive Motor Bracket
Drive Motor
Lift Frame
Filter Wire
Rear Roller Ground Wire
Reed Switch
Reed Switch Clip
Belly Pan
Reset/Off Circuit Breaker
Receptical
Power Cord
Controller
Left Upright
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Right Upright
Left Upright Spacer
Right Upright Spacer
Base Endcap
Caution Decal
Incline Motor
Upright Wire
Base Pad
Base
Base Wheel
Releasable Tie
Cable Tie
Book Rack
Right Tray
Left Tray
Console
Key/Clip
Hood Clip
Incline Motor Spacer
Console Ground Wire
Console Back
Left Grip Bracket
Access Door
Right Grip Bracket
Latch Warning Decal
15.5" Wire Tie
Lift Frame Wire Tie
Wire Tie
8" Green Wire, F/Ring
6" Green Wire, F/Ring
10" Red Wire, M/F
8" Black Wire, M/F
4" Black Wire, 2F
10" Blue Wire, M/F
10" Blue Wire, 2F
4" White Wire, 2F
User’s Manual
Isolator Fastener
ProShox Decal
Left Foot Rail
Isolator
Belt Guide
Frame Spacer
Front Roller Spacer
Magnet
Front Roller/Pulley
Motor Belt
Right Foot Rail
Walking Belt
Walking Platform
Rear Roller
Rear Roller Bracket
Left Rear Foot
Hex Key
Right Rear Foot
Frame
Latch Knob
Latch Assembly
*
*
*
*
*
*
*
*
*These parts are not illustrated
Specifications are subject to change without notice.
If a part is missing, call 1-888-533-1333.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. 831.24745.3
R0607A
4
8
0
4
9
3
3
3
6
2
1
3
5
4
1
5
5
3
1
2
5
4
8
3
5
3
4
4
4
6
3
3
4
2
4
1
2
1
3
4
0
5
8
4
3
5
1
4
1
2
3
1
3
2
9
4
1
2
2
6
5
2
4
9
1
3
2
6
4
6
1
3
2
0
2
5
7
7
3
2
3
8
7
3
8
4
2
1
6
2
1
5
9
0
5
8
4
2
1
5
1
4
2
1
0
7
2
2
9
8
4
2
6
1
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. 831.24745.3
R0607A
10
34
10
34
10
34
57
23
29
97
32
23
20
58
22
59
15
60
24
61
31
62
15
63
1
70
64
69
2
12
65
2
68
2
67
2
66
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. 831.24745.3
R0607A
7
5
7
5
17
31
71
78
77
18
6
7
31
5
89
75
6
73
9
7
8
5
19
72
76
3
80
25
79
56
8
19
75
4
78
6
8
79
56
79
56
81
74
96
76
8
3
3
9
6
9
25
79
56
81
4
83
82
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. 831.24745.3
R0607A
88
86
84
87
10
85
98
20
91
30
10
10
90
10
92
10
10
10
10
93
1
10
10
1
10
30
10
10
1
94
1
10
1
10
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222 Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
®
1-888-SU-HOGAR (1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
ONE YEAR FULL WARRANTY
If this Sears Treadmill Exerciser fails due to a defect in material or workmanship within 1 year of the date
of purchase, call 1-800-4-MY-HOME® (1-800-469-4663) to arrange for free repair (or replacement if re-
pair proves impossible). The incline motor is warranted for 1 year from the date of purchase; the drive
motor is warranted for 12 years from the date of purchase.
This warranty does not apply when the Treadmill Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Part No. 255359 R0607A
Printed in USA © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|