Patent Pending
Model No. PFEL03010
Serial No.
USER’S MANUAL
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future
reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the PROFORM® 515S elliptical trainer.
1. Read all instructions in this manual before
using the elliptical trainer.
9. Wear appropriate clothing when using the
elliptical trainer. Always wear athletic shoes
for foot protection.
2. Use the elliptical trainer only as described in
this manual.
10. When mounting and dismounting the ellipti-
cal trainer, always hold the handlebars or
the T-handle and step onto and off the pedal
that is in the lowest position.
3. It is the responsibility of the owner to ensure
that all users of the elliptical trainer are ade-
quately informed of all precautions.
11. Each time you stop exercising on the
elliptical trainer, allow the pedals to come to
a complete stop before dismounting.
4. The elliptical trainer is intended for in-home
use only. Do not use the elliptical trainer in a
commercial, rental, or institutional setting.
12. Always keep your back straight when using
the elliptical trainer. Do not arch your back.
5. Place the elliptical trainer on a level surface,
with a mat beneath it to protect the floor or
carpet. Keep the elliptical trainer indoors,
away from moisture and dust.
13. The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
6. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
7. Keep children under the age of 12 and pets
away from the elliptical trainer at all times.
14. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
8. The elliptical trainer should not be used by
persons weighing more than 250 pounds.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health
problems. Read all instructions before using. ICON assumes no responsibility for personal injury
or property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the PROFORM® 515S
elliptical trainer. The 515S is an incredibly smooth
exerciser that moves your feet in a natural elliptical
path, minimizing the impact on your knees and ankles.
And the unique 515S features adjustable resistance,
upper-body and stationary handlebars, and a multi-
mode console to help you get the most from your
exercise. Welcome to a whole new world of natural,
elliptical-motion exercise from PROFORM.
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is PFEL03010. The
serial number can be found on a decal attached to the
elliptical trainer (see the front cover of this manual for
the location of the decal).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
you use the elliptical trainer. If you have questions
after reading the manual, call our Customer Service
Water Bottle Holder
(Bottle not included)
Book Holder
Resistance Knob
T-Handle/Pulse Sensor
Handlebar
Upright
FRONT
Side Shield
Pedal Disk
Pedal
Pedal Arm
LEFT SIDE
BACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Use the chart below to identify the small parts used in
assembly. The number in parenthesis below each part
refers to the key number of the part, from the PART
LIST on page 14. The number after the dash indicates
the quantity needed for assembly. Note: Some parts
may have been pre-attached for shipping. If a part
is not in the parts bag, check to see if it has been
pre-attached.
M4 x 16mm Screw
(34)—5
M4 x 19mm Flange
Screw (16)–6
M6 x 16mm Screw (54)—2
M6 Black Nylon Locknut (55)—2
M10 Nylon Locknut (29)—4
Weld Spacer (49)—2
3/4” Axle Cap (43)—4*
5/8” Axle Cap (57)—2*
Rear Pedal Arm Bushing (11)—8
Handlebar Spacer (39)—2
Pedal Arm Spacer (41)—2
* Extra parts may be included.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Place all parts of the elliptical trainer in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires that you have a phillips screwdriver
rubber mallet , and a pair pliers
, two adjustable wrenches
, a
.
1. While another person holds the Console (6) near the
Upright (3), insert the Resistance Cable (26) down
through the Upright.
1
6
26
3
2. While another person holds the Upright (3) near the
Frame (1) as shown, connect the Extension Wire
(61) to the Sensor Wire (25).
2
29
3
Next, connect the Resistance Cable (26) to the
Lower Cable (59) in the following way:
• Refer to drawing A. Pull up on the metal bracket,
and insert the tip of the Resistance Cable (26) into
the wire clip on the Lower Cable (59) as shown.
• Refer to drawing B. Firmly pull the Resistance
Cable (26) and slide it into the metal bracket on the
Lower Cable (59) as shown.
26
59
61
1
• Refer to drawing C. Using pliers, squeeze the
prongs on the upper end of the metal bracket
together.
25
Slide the Upright (3) onto the welded bolts on the
Frame (1). Make sure that the Lower Cable (59)
doesn’t become caught on the Upright or the
Frame. Be careful to avoid pinching the Lower
Cable, the Resistance Cable (26), the Sensor
Wire (25), or the Extension Wire (61) between the
Upright and the Frame. Tighten an M10 Nylon
Locknut (29) onto each welded bolt.
Welded
Bolts
A
B
C
Metal
Bracket
26
26
59
26
59
59
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert the pulse wires beneath the indicated bracket
on the Upright (3) and up out of the hole in the top of
the Upright. Attach the T-Handle (10) to the Upright
with two M6 x 16mm Screws (54) and two M6 Black
Nylon Locknuts (55).
3
Pulse
Wires
Hole
Bracket
54
3
10
55
4. While another person holds the Console (6) near the
Upright (3), attach the ground wire to the Upright with
an M4 x 16mm Screw (34). Connect the Extension
Wire (61) to the corresponding console wire. Connect
the pulse wires to the corresponding console wires.
4
50
6
26
Console
Wires
Pull any slack Resistance Cable (26) up out of the
Upright (3) and push it into the Console (6). Feed the
slack Extension Wire (61) down into the Upright.
Attach the Console to the Upright with four M4 x
16mm Screws (34). Be careful to avoid pinching
the wires or pinching or kinking the Resistance
Cable.
26
Pulse Wires
61
34
Ground
Wire
Press the Resistance Knob (50) onto the upper end
of the Resistance Cable (26).
34
3
5. Find the Left Pedal (31), which has a ridge on the
right side. Attach the Left Pedal to one of the Pedal
Arms (12) with three M4 x 19mm Round Head
Screws (16) as shown.
5
Ridge
31
Repeat this step to attach the Right Pedal to the other
Pedal Arm (not shown).
12
16
6. Locate the Left Handlebar (8) (there is an “L” sticker
on the Left Handlebar for identification). Apply a thin
film of the included grease to the axle at the lower
end of the Left Handlebar.
6
62
8
12
Slide a Handlebar Spacer (39) and the Pedal Arm
(12) with the Left Pedal (31) onto the Left Handlebar
(8) as shown. Make sure that there are two Pedal
Arm Bushings (11) in the Pedal Arm. (Note: These
parts fit tightly; it may be helpful to use a rubber mal-
let). Next, refer to the PART IDENTIFICATION
CHART on page 5 and identify the 3/4” Axle Caps
(43). Tap a 3/4” Axle Cap onto the Left Handlebar.
39
11
43
Grease
12
Repeat this step to attach the other Pedal Arm (12) to
the Right Handlebar (62).
31
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Slide a Weld Spacer (49) onto the left axle on the
Upright (3). Make sure that the open side of the Weld
Spacer is facing the Upright.
7
Apply a thin film of the included grease to the axles
and the Crank Arms (59) in the locations indicated.
Slide a Pedal Arm Spacer (41) onto the left Crank
Arm (59). Make sure that there are two Rear Pedal
Arm Bushings (11) in the Pedal Arm (12) attached to
the Left Handlebar (8).
Grease
57
8
With the help of another person, slide the Left
Handlebar (8) onto the left axle on the Upright (3)
while sliding the left Pedal Arm (12) onto the left
Crank Arm (59). Note: These parts fit tightly; it may be
helpful to use a rubber mallet. In addition, it may be
helpful to rotate the left Crank Arm (59) to a different
position.
49
Grease
3
Grease
59
Tap a 5/8” Axle Cap (57) onto the left axle on the
Upright (3). Tap a 3/4” Axle Cap (43) onto the left
Crank Arm (59).
41
12
Repeat this step to attach the Right Handlebar and
the right Pedal Arm (not shown).
11
43
8. The Console (6) requires four “AA” batteries (not
included). Alkaline batteries are recommended.
8
6
To install batteries, look under the Console (6) and
locate the two Battery Covers (9) (there is one Battery
Cover on each side). Remove the Battery Covers by
sliding them in the direction shown by the arrows on
the Battery Covers. Insert two batteries into each bat-
tery compartment; make sure that all four batteries
are turned so the negative ends (marked “–”) are
touching the springs in the battery compartments.
Then, reattach the Battery Covers by sliding them in
the opposite direction.
Batteries
9
9. Make sure that all parts of the elliptical trainer are properly tightened. Place a mat under the elliptical
trainer to protect the floor or carpet from damage.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL TRAINER
HOW TO EXERCISE ON THE ELLIPTICAL TRAINER
DESCRIPTION OF THE CONSOLE
To mount the elliptical trainer, firmly hold the handle-
bars or the T-handle and carefully step onto the pedal
that is in the lowest position. Next, step onto the other
pedal. Push the pedals until they begin to move with a
continuous motion. Note: The pedal disks can turn
in either direction. It is recommended that you
turn the pedal disks in the direction shown below;
however, to give variety to your exercise, you may
choose to turn the pedal disks in the opposite
direction.
Pedal Disk
The innovative console offers a manual mode and
three personal coach pace programs. The pace pro-
grams are designed to help you achieve specific exer-
cise goals by pacing your exercise. You can choose
from a stamina-building interval program, an aerobic
program, and a special fat burning program. The con-
sole also features six modes that display instant exer-
cise feedback. The modes are described below:
Calories—This mode shows the approximate number
of calories you have burned.
Pedal
Fat Calories—This mode shows the approximate
number of fat calories you have burned (see Burning
Fat on page 12).
To dismount the elliptical trainer, allow the pedals to
come to a complete stop. CAUTION: The elliptical
trainer does not have a free wheel; the pedals will
continue to move until the flywheel stops. When
the pedals are stationary, step off the highest pedal
first. Then, step off the lowest pedal.
Time—If you select the manual mode, this mode will
show the elapsed time. If you select one of the three
pace programs, this mode will count down the time
remaining in the program. Note: When you stop exer-
cising, the time will flash when it is displayed.
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS
Distance—This mode shows your total distance, in
miles.
As you exercise,
you can adjust
the resistance of
the pedals with
the resistance
knob on the
Speed—This mode shows your exercise pace, in
miles per hour.
Resistance Knob
Scan—This mode displays the other five modes, for
seven seconds each, in a repeating cycle.
console. To
increase the
resistance,
Pulse—This mode shows your heart rate when the
pulse sensor is used.
turn the knob
clockwise; to
decrease the
resistance, turn the knob counterclockwise.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW THE PACE PROGRAMS OPERATE
Select one of the three pace programs or the
manual mode
2
When you use a
pace program, two
columns of bars will
appear in the upper
display. The left col-
umn represents a
To select one of
the pace
programs,
repeatedly press
the program
select button. A
Indicator
Target Pace Actual Pace
target pace, and the
right column shows
1, 2, or 3 will
your actual exercise
appear in the upper display to show which pro-
gram you have selected. To select the manual
mode, press the program select button until no
number appears in the upper display. The pro-
grams will be selected in the following order: pro-
gram 1 (interval), program 2 (aerobic), program 3
(fat burn), manual mode.
pace. The target pace will change periodically during
the program; as the target pace changes, simply
adjust your pace to keep both columns at the same
height. Important: The target pace is a goal pace.
Your actual pace may be slower than the target
pace, especially during the first few months of
your exercise program. Be sure to exercise at a
pace that is comfortable for you.
Begin your workout
3
The three graphs
on the console
If you selected
the manual
show how the target
pace will change
during the
programs. During
mode, go to
step 4. If you
selected one of
the pace pro-
the Aerobic
Actual Pace
grams, two
Target Pace
program (program 2), for example, the target pace will
gradually increase during the first half of the program,
and gradually decrease during the last half of the pro-
gram. Each program will last for twenty minutes.
columns of bars
will appear in
the upper display. The left column will show a
target pace. The right column will show your
actual exercising pace. Adjust your pace until the
same number of bars appear in both columns.
The arrows on the right side of the upper display
will show whether you need to increase or
decrease your pace. Each time the target pace
changes during the program, adjust your pace to
keep both columns at the same height.
STEP-BY-STEP CONSOLE OPERATION
Before the console can be operated, batteries
must be installed. See assembly step 8 on page 8.
Follow the steps below to operate the console.
Turn on the power
Follow your progress with the six feedback
modes
1
4
To turn on the
power, press
The scan
the on/reset
mode—
button or
simply begin
Repeatedly
press the mode
Bar
exercising.
button until a
The entire dis-
bar appears
play will appear for two seconds; the console will
then be ready for use. Note: If batteries were just
installed, the power will already be on.
above the scan
symbol. When the scan mode is selected, the con-
sole will display the calories, fat calories, time,
distance, and speed modes, for seven seconds
each, in a repeating cycle.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
the upper contacts and your fingers must be
touching the lower contacts. Avoid moving your
hands. After a moment, the heart-shaped indica-
tor in the display will begin to flash and your
heart rate will be shown. For the most accurate
heart rate reading, continue to hold the contacts
for about 15 seconds.
The calories,
fat calories,
time, distance,
or speed
mode—
Repeatedly
press the
mode button until a bar appears below or above
the name of the desired mode. (Note: When the
time mode is selected, no bar will appear; when
the speed mode is selected, the letters MPH will
appear instead of a bar.) Make sure that there is
not a bar above the word “scan.”
Make sure that your hands are positioned as
described above, and that you are not moving
your hands excessively or squeezing the metal
contacts too tightly.
If desired, press the on/reset button to reset the
lower display.
WARNING:
The pulse sensor is
not a medical device. Various factors, includ-
ing the user’s movement, may affect the accu-
racy of heart rate readings. The pulse sensor
is intended only as an exercise aid in deter-
mining heart rate trends in general.
Measure your heart rate if desired
5
Note: If the
metal contacts
on the pulse
sensor are cov-
ered by thin
sheets of plas-
tic, peel off the
plastic.
Turn off the power
6
Metal
Contacts
To turn off the power, simply wait for about
six minutes. If the pedals are not turned and the
buttons are not pressed for six minutes, the
power will turn off automatically.
To use the pulse sensor, place your hands on the
metal contacts. Your palms must be resting on
MAINTENANCE
Inspect and tighten all parts of the elliptical trainer
regularly. Replace any worn parts immediately.
• Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
The elliptical trainer can be wiped clean with a soft
cloth and mild detergent. Do not use abrasives or
solvents. To prevent damage to the console, keep
liquids away from the console. Use only a sealable
water bottle in the console.
• For the most accurate heart rate reading, hold the
metal contacts for about 15 seconds.
• For optimal performance of the pulse sensor, keep
the metal contacts clean. The contacts can be
cleaned with a soft cloth—never use alcohol,
abrasives, or chemicals.
CONSOLE TROUBLE-SHOOTING
If the console does not function properly, the batteries
should be replaced. To replace the batteries, refer to
assembly step 8 on page 8.
STORAGE
When storing the elliptical trainer, remove the batter-
ies from the console. Keep the elliptical trainer in a
clean, dry location, away from moisture and dust.
PULSE SENSOR TROUBLE-SHOOTING
• Avoid moving your hands while using the pulse sen-
sor. Excessive movement may interfere with heart
rate readings.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
the first few minutes of exercise, your body uses easi-
ly accessible carbohydrate calories for energy. Only
after the first few minutes of exercise does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the intensity of your exercise until
your heart rate is near the smallest number in your
training zone as you exercise. For maximum fat burn-
ing, adjust the intensity of your exercise until your
heart rate is near the middle number.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over the age of 35 or persons with pre-exist-
ing health problems.
Aerobic Exercise
The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
To strengthen your cardiovascular system, your exer-
cise must be “aerobic.” Aerobic exercise is activity
that requires large amounts of oxygen for prolonged
periods of time. This increases the demand on the
heart to pump blood to the muscles, and on the lungs
to oxygenate the blood. For aerobic exercise, adjust
the intensity of your exercise until your heart rate is
near the largest number in your training zone.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
Each workout should include the following three parts:
A Warm-up
Begin each workout 5 to 10 minutes of stretching and
light exercise (see page 13). A proper warm-up
increases your body temperature, heart rate, and cir-
culation in preparation for exercise.
Training Zone Exercise
After warming up, exercise for 20 to 30 minutes with
your heart rate in your training zone. (During the first
few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.)
A Cool-down
Finish each workout with 5 to 10 minutes of stretching.
This will increase the flexibility of your muscles and
will help to prevent post-exercise problems.
To find the proper heart rate, first find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The smallest number is the recommended heart rate
for fat burning; the middle number is the heart rate for
maximum fat burning; the largest number is the heart
rate for aerobic exercise.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three work-
outs each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may plan up to five workouts each week, if desired.
Burning Fat
Remember, the key to success is make exercise a
regular and enjoyable part of your everyday life.
To burn fat effectively, you must exercise at a low
intensity level for a sustained period of time. During
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
3
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFEL03010
R1101A
Key
Key
No. Qty.
Description
No. Qty.
Description
1
2
3
4
5
6
7
8
1
2
1
1
1
1
2
1
2
1
8
2
11
1
1
6
2
2
2
2
1
2
1
1
1
1
4
1
4
1
1
1
2
12
Frame
Pulse Grip
Upright
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
#
2
2
2
4
2
1
2*
1
4*
1
1
4
1
1
2
1
4
1
2
2
2
4*
2*
1
1
1
1
1
1
1
2
1
1
1
5/16” Zinc Bolt
Pulley Bearing
Pedal Disk
M4 x 16mm Round Head Screw
Handlebar Spacer
Side Shield Bracket
Pedal Arm Spacer
Console Back
3/4” Axle Cap
M4 x 16mm Flat Head Screw
Right Pedal
#8 Flat Washer
Clamp Nut
Clamp Bolt
Right Side Shield
Left Side Shield
Console
Foam Handlebar Grip
Left Handlebar
Battery Cover
T-Handle
Pedal Arm Bushing
Pedal Arm
M5 x 16mm Screw
Resistance Strap
Strap Buckle
M4 x 19mm Flange Screw
M6 Nut
Adjustment Bracket
M6 Eyebolt
M8 Nylon Jam Nut
Flywheel Axle
Flywheel Bearing
Flywheel
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Weld Spacer
Resistance Knob
M4 x 25mm Screw
Return Spring
M8 Washer
M6 x 16mm Button Screw
M6 Black Nylon Locknut
Pivot Bushing
5/8” Axle Cap
M4 x 64mm Screw
Lower Cable
3/4” Plastic Spacer
Extension Wire
Right Handlebar
Nylon Washer
User’s Manual
Side Shield Decal
Warning Decal
Magnet
Sensor Wire/Reed Switch
Resistance Control/Cable
Stabilizer Endcap
Tension Spring
M10 Nylon Locknut
Belt
Left Pedal
Pulley w/Shaft
Crank Arm
#
#
#
#
Hardware Kit
Grease Packet
M4 x 16mm Screw
Note: “#” indicates a non-illustrated part. “ ” indicates that an extra part may be included. Specifications are
*
subject to change without notice. See the back cover of this manual for information about ordering replacement
parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFEL03010
R1101A
13
58
4
50
6
13
9
34
62
13
34
42
51
38
57
61
26
56
34
56
5
34
38
7
38
34
49
30
45
43
11
54
3
8
49
56
29
12
10
16
17
11
43
56
39
57
55
41
20
18
11
31
27
19
22
22
23
2
53
17
18
53
39
24
47
11
28
1
13
19
21
20
48
46
52
35
43
12
59
34
36
60
41
33
40
13
36
11
27
25
32
16
37
33
11
63
44
43
15
27
14
35
27
37
13
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
• The MODEL NUMBER of the product (PFEL03010)
• The NAME of the product (PROFORM® 515S elliptical trainer)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see page 14).
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service cen-
ters with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to
a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center, to products used for commercial or rental pur-
poses, or to products used as store displays. No other warranty beyond that specifically set forth above
is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 175920 R1101A
Printed in China © 2001 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|