Model No. PFB38031
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis-
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
11. Always set both barbell guides and both
safety spotters at the same height.
12. Make sure that the set screws attaching the
Olympic weight adapters are properly tight-
ened each time the adapters are used.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
13. The weight bench is designed to support a
maximum user weight of 300 pounds and a
maximum total weight of 610 pounds. Do not
place more than 310 pounds on the barbell
or safety spotters. Do not place more than
150 pounds on the leg lever or curl bar. Note:
The weight bench does not include weights.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
14. Always place an equal amount of weight on
each side of the barbell.
5. Keep the weight bench indoors, away from
moisture and dust. Do not put the weight
bench in a garage or covered patio, or near
water.
15. Always secure the weights with the weight
clips when they are mounted on the barbell.
6. Make sure all parts are properly tightened
each time the weight bench is used. Replace
any worn parts immediately.
16. Always make sure the backrest bracket is
fully engaged before using the backrest.
17. Always mount the “L”-bracket onto the cen-
ter base before performing press exercises.
7. Keep children under 12 and pets away from
the weight bench at all times.
18. Always move your bench out of the way
when performing an exercise that does not
use the bench.
8. Keep hands and feet away from moving parts.
9. Always wear athletic shoes for foot protec-
tion while exercising.
19. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
10. Use the curl bar only with the weight clips
provided with the bench.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile PROFORM®
C820 weight bench. The weight bench offers an
impressive array of weight stations designed to devel-
op every major muscle group of the body. Whether
your goal is to tone your body, build dramatic muscle
size and strength, or improve your cardiovascular sys-
tem, the weight bench will help you to achieve the
specific results you want.
toll-free at 1-888-533-1333, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is PFB38031. The serial number can be found
on a decal attached to the weight bench (see the front
cover of this manual for the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
ASSEMBLED
DIMENSIONS:
Height: 75 in.
Width: 84 in.
Length: 30 in.
Right Side
Locking Bar
Left Side
Guide Bar
Curl Pad
Barbell
Upright
Backrest
Safety Spotter
Seat
Leg Lever
Curl Bar
Note: The “right side” and the “left side” are
determined relative to a person sitting on the
bench; they do not correspond to right and
left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
1.
1
Before beginning, make sure you under-
76
69
stand the information in the box above.
Note: Some parts described in the assem-
bly steps may be pre-assembled.
1
79
Attach a Base Cap (9) to the Stabilizer (2) with an
M4 x 16mm Screw (58) and an M10 x 25mm
Button Screw (78). Attach another Base Cap to
the Stabilizer in the same manner.
67
69
67
9
2
9
Attach the Stabilizer (2) and the “L”-bracket (76)
to the Bench Frame (1) with two M10 x 95mm
Carriage Bolts (61) and two M10 Nylon Locknuts
(69). Secure the Stabilizer to the Bench Frame
with two M10 x 68mm Button Bolts (79), two M10
Washers (67), and two M10 Nylon Locknuts. Do
not tighten the Locknuts yet.
58
78
61
2
79
67
1
2. Attach the Small Base Cap (80) to the Bench Leg
(3) with an M4 x 16mm Screw (58).
69
Attach the Bench Leg (3) to the Bench Frame (1)
with two M10 x 68mm Button Bolts (79), two M10
Washers (67), and two M10 Nylon Locknuts (69).
69
3
80
58
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the Leg Lever Bracket (7) to the Bench
Frame (1) with two M10 x 68mm Button Bolts
(79) and two M10 Nylon Locknuts (69).
3
7
69
Lubricate
79
Attach the Weight Tube (11) to the Leg Lever (4)
with an M8 x 58mm Button Bolt (71), two M8
Washers (73), a 10mm Spacer (25), and an M8
Nylon Locknut (72). Press a 25mm Round Outer
Cap (24) onto the Weight Tube.
4
1
24
72
11
79
Lubricate an M10 x 68mm Button Bolt (79) with
grease. Attach the Leg Lever (4) to the Leg Lever
Bracket (7) with the Bolt and an M10 Nylon
Locknut (69). Do not overtighten the Locknut;
the Leg Lever must be able to pivot easily.
73
25
71
73
4. Lubricate an M10 x 78mm Button Bolt (75) with
grease. Attach the lower hole in the Adjustment
Lever (8) to the tube on the bottom of the Bench
Frame (1) with the Bolt and an M10 Nylon Locknut
(69). Do not overtighten the Locknut; the
4
Adjustment Lever must be able to pivot easily.
1
Hold the handle on the Adjustment Lever (8) so
that the upper hole is above the Bench Frame (1).
Slide the M10 x 62mm Flat Head Screw (77)
through the indicated side of the Lever, over the
Bench Frame, and tighten it into the other side of
the Adjustment Lever. Make sure that the threads
of the Screw show through the Adjustment
Lever. Do not overtighten the Screw.
Tube
69
77
8
75
Lubricate
Handle
5. Attach the Backrest Bracket (10) to the Backrest
Tubes (6) with four M10 x 45mm Button Bolts
(74), four M10 Washers (67), and four M10 Nylon
Locknuts (69). Make sure the Backrest Tubes
are oriented so that the indicated holes are
closer to the bottom. Do not tighten the
Locknuts yet.
5
6
Holes
67
74
67
74
69
69
10
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Insert the Backrest Bracket (10) through the slot
in the Bench Frame (1) and under the Adjustment
Lever (8). Make sure that the M10 x 62mm Flat
Head Screw (77) is in a notch under the
Backrest Bracket.
6
6
69
67
10
77
Lubricate an M10 x 155mm Button Bolt (85) with
grease. Attach the Backrest Tubes (6) to the
Bench Frame (1) with the Bolt, two M10 Washers
(67), and an M10 Nylon Locknut (69). Do not
overtighten the Locknut; the Backrest Tubes
must be able to pivot easily.
1
85
67
8
Lubricate
7. Attach the Backrest (12) to the Backrest Tubes
(6) with four M6 x 38mm Screws (64) and four M6
Washers (68).
7
12
Tighten the six M10 Nylon Locknuts (69) used
in step 5.
6
68
64
68
64
8. Attach the Seat (13) to the Bench Frame (1) with
an M6 x 63mm Screw (65), an M6 Washer (68),
and two M6 x 16mm Screws (63).
8
13
1
68
65
63
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Slide a Pad Tube (50) into a hole in the Leg
Lever (4). Wet both sides of the Pad Tube with
soapy water. Slide two Large Foam Pads (51)
onto the Pad Tube as shown. Press two 19mm
Square Inner Caps (53) into the Pad Tube.
Repeat with the other Pad Tube and the Leg
Lever.
9
53
7
52
53
51
82
4
52
Slide the Long Pad Tube (82) into the hole in the
Leg Lever Bracket (7). Wet both sides of the Pad
Tube with soapy water. Slide two Small Foam
Pads (52) onto the Tube as shown. Press two
19mm Square Inner Caps (53) into the Pad Tube.
50
50
53
51
53
10. Attach the Curl Pad (14) to the Curl Post (5) with
two M6 x 16mm Screws (63).
10
14
5
63
11. Press a Round Angled Bushing (45) into a Rack
Foot (35).
11
Attach a Guide Bar (32) to the Rack Foot (35)
with an M10 x 30mm Button Screw (56) and an
M10 Washer (67). Tighten the Screw.
32
62
Using a rubber mallet, tap the Right Upright (62),
which has numbers on the indicated side, onto
the Rack Foot (35). Attach the Right Upright to
the Rack Foot with two M10 x 65mm Button Bolts
(60), four M10 Washers (67), and two M10 Nylon
Locknuts (69). Make sure the Bolts are inserted
from the side shown. Do not tighten the
Locknuts yet.
Numbers
Repeat this step with the Left Upright (31 [not
shown]), Guide Bar (32), and Rack Foot (35).
Insert the M10 x 65mm Button Bolts (60) from
the other side.
67
69
67
67
60
67
45
35
67
56
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Attach a Base Cap (9) and a Rear Support (29) to
the a Base (28) with two M10 x 93mm Button
Bolts (48), an M10 Washer (67), an M10 Nylon
Locknut (69), an M10 Nylon Jamnut (26), and an
M4 x 16mm Screw (58).
12
29
48
Repeat this step with the other Base (28) and
Rear Support (29).
48
9
28
26
58
67
69
13. Attach a Base (28) to the Center Base (27) with
three M10 x 68mm Button Bolts (79), three M10
Washers (67), and two M10 Nylon Locknuts (69).
Do not tighten the Locknuts yet.
13
27
Attach the other Base (28) to the Center Base
(27) in the same manner.
69
69
67
28
79
14. Attach the Crossbar (30) to a Rear Support (29)
with two M10 x 68mm Button Bolts (79), two M10
Washers (67), and two M10 Nylon Locknuts (69).
Do not tighten the Locknuts yet.
14
79
Attach the Crossbar (30) to the other Rear
Support (29) in the same manner.
30
79
67
69
29
67
9
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Using a rubber mallet, tap the left Rack Foot (35)
into the indicated Base (28). Attach the Foot to
the Base with two M10 x 65mm Button Bolts (60),
four M10 Washers (67), and two M10 Nylon
15
Locknuts (69). Do not tighten the Locknuts yet.
31
79
Attach the Left Upright (31) to the Rear Support
(29) with two M10 x 68mm Button Bolts (79) and
two M10 Nylon Locknuts (69). Do not tighten the
Locknuts yet.
69
Attach the right Rack Foot (not shown) and
Right Upright (not shown) in the same man-
ner.
29
79
69
60
67
28
67
69
67
35
16. Attach the Right Spotter Hook (39) to a Safety
Spotter (38) with an M8 x 12mm Shoulder Bolt (57)
and an M8 Nylon Locknut (72). Make sure the
bolt head is on the same side as the handle.
16
Handle
39
40
38
72
Slide the Safety Spotter (38) onto the right Guide
Bar (32) and engage the Right Spotter Hook (39)
into an adjustment hole near the bottom of the
Right Upright (62).
38
57
62
Assemble the Left Spotter Hook (40) and a
Safety Spotter (38) in the same manner.
32
Adjustment Hole
17. Identify the Left and Right Barbell Gliders (37, 81)
by the position of the screw holes.
17
Slide each Barbell Glider (37, 81) onto the Guide
Bar (32) next to the indicated Upright (31, 62).
Make sure the Barbell Gliders are oriented as
shown.
37
32
81
Screw
Hole
Screw
Hole
32
62
31
10
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Press a Top Bracket Bushing (55) into the Top
Bracket (36). Using a rubber mallet, tap the Top
Bracket onto the Left Upright (31) and the Guide
Bar (32).
18
56
67
36
67
Attach the Top Bracket (36) to the Left Upright
(31) with two M10 x 65mm Button Bolts (60), four
M10 Washers (67), and two M10 Nylon Locknuts
(69). Do not tighten the Locknuts yet.
55
60
67
67
32
Attach the Top Bracket (36) to the Guide Bar (32)
with an M10 x 30mm Button Screw (56) and an
M10 Washer (67).
69
31
Assemble the other Top Bracket (36) in the
same manner.
19
19. Have a second person orient the Locking Bar (34)
as shown and hold it between the Left and Right
Barbell Gliders (37, 81).
62
81
31
Slide the Weight Bar (33) through the Left Barbell
Glider (37), the Locking Bar (34), and the Right
Barbell Glider (81).
34
37
Engage the hooks on the Locking Bar (34) into a
set of holes in the Uprights (31, 62).
33
20. Slide a Weight Stop (42) onto the Weight Bar
(33). Thread a 1/4” x 14mm Button Screw (59)
into the Weight Stop and the hole in the Weight
Bar. Do not tighten the Screws yet.
20
33
37
Thread a 1/4” x 14mm Button Screw (59) into the
Left Barbell Glider (37).
42
59
Repeat this step with the Right Barbell Glider
(not shown) and the other Weight Stop (not
shown).
59
21. Slide a Barbell Adapter (41) onto the Weight Bar
(33). Thread a 1/4” x 9.5mm Allen Head Set
Screw (66) into the Barbell Adapter. Do not tight-
en the Screw yet.
21
33
Repeat this step with the other Barbell
Adapter (not shown).
41
Tighten the M10 Nylon Locknuts (69) used in
steps 11–21. Tighten the 1/4” x 14mm Button
Screws (59) and 1/4” x 9.5mm Allen Head Set
Screw (66) used in steps 20 and 21.
66
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 15 for impor-
tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
To adjust the position of the Backrest (12), hold the
upper end of the Backrest with one hand and lift the
Adjustment Lever (8) with the other hand, disengag-
12
ing the Backrest Bracket (10). Raise or lower the
Backrest to the desired position. Lower the Adjust-
ment Lever so that the M10 x 62mm Flat Head Screw
(77 [not shown]) engages one of the notches in the
Backrest Bracket.
77
WARNING:
Always hold the
Backrest (12) securely before disengaging the
Backrest Bracket (10). Always make sure the
Backrest Bracket is fully engaged before using
the Backrest.
8
10
ATTACHING THE CURL POST
For some exercises, the Curl Post (5) must be
attached to the weight bench. Slide the Curl Post into
the Leg Lever Bracket (7). Align the adjustment holes
in the Curl Post with the adjustment hole in the Leg
Lever Bracket. Tighten the Curl Knob (22) into the
adjustment hole in the Leg Lever Bracket. Fully tight-
en the Knob.
5
7
22
12
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE BENCH FOR PRESS EXERCISES
To prevent the weight rack from tipping while perform-
ing press exercises on the bench, set the “L”-bracket
(76) over the Center Base (27).
76
27
USING THE OLYMPIC WEIGHT ADAPTER
Press a 48mm Round Inner Cap (16) into the Olympic
Adapter (15). Attach the Olympic Adapter to the
Weight Tube (11) with a 1/4” x 9.5mm Allen Head Set
Screw (66). Make sure that the Set Screw is in the
bottom of the Adapter.
11
15
Press a 48mm Round Inner Cap (16) into a Weight
Adapter (49). Attach the Weight Adapter to the Curl
Bar (47) with a 1/4” x 9.5mm Allen Head Set Screw
(66). Make sure that the Set Screw is in the bot-
tom of the Adapter. Attach the other Weight
Adapter to the Curl Bar in the same manner.
66
16
49
47
16
66
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (4), slide the desired weights
(not included) onto the Weight Tube (11). Secure the
weights with a Weight Clip (83 or 84 [not shown]).
4
Weights can be added to the Curl Bar (not shown) in
the same manner. Secure the weights to the Curl Bar
with two Weight Clips (83 or 84 [not shown]).
Weight
WARNING:
Do not place more
than 150 pounds on the Weight Tube (11) or the
Curl Bar (47).
11
83
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE BARBELL OR THE
WEIGHT CARRIAGE
84
To use the barbell, slide the desired amount of weight
(not included) onto the Barbell Adapters (41). Secure
the weights with the Large Weight Clips (84).
41
WARNING:
Do not place more than
62
Weight
310 pounds on the barbell. Always place the
same amount of weight on each side of the bar-
bell. Always secure weights with the Large
Weight Clips (84).
Weight
Your weights can be stored on the tubes on the
Uprights (31 [not shown], 62) (see the inset drawing).
USING THE LOCKING BAR
Before starting an exercise, position the Locking Bar
(34) and the Safety Spotters (not shown) in the correct
position for the exercise.
34
31
To do this, stand in front of the rack and grip the
Locking Bar (34) with both hands. Turn the Locking Bar
until the two hooks disengage the slots in the Uprights
(31, 62 [not shown]). Raise or lower the Locking Bar to
a new position and turn it until the hooks engage the
slots in the Uprights.
37
USING THE SAFETY SPOTTERS
62
To move the Safety Spotters (38) to a new position,
grip the handles on the Spotter Hooks (39, 40 [not
shown]) and pull the hooks out of the slots in the
Uprights (31 [not shown], 62). Raise or lower the
Safety Spotters to new positions and pivot the hooks
back into the slots in the Uprights. Note: Always
position the Safety Spotters at the lowest point to
which you want the barbell to move during the
exercise.
39
Handle
38
WARNING:
Always set both Safety
Spotters (38) at the same height.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
MUSCLE BUILDING
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
WARMING UP
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
right for you. Begin with 3 sets of 8 repetitions for each your body for more strenuous exercise by increasing
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
TONING
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of resistance and increase the number of rep-
etitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by com-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
pleting more sets rather than by using high amounts of Schedule your workouts for the time of day when your
resistance.
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
WEIGHT LOSS
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
CROSS TRAINING
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or
exercise bike, on Tuesday and Thursday.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
• Rest from both strength training and aerobic exercise The repetitions in each set should be performed
for at least one full day each week to give your body
time to regenerate.
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
The combination of strength training and aerobic exer-
cise will reshape and strengthen your body, plus devel- during the return stroke. Never hold your breath.
op your heart and lungs.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on pages 17–19 of this manual can be photo-
copied and used to schedule and record your work-
outs. List the date, the exercises performed, the resist-
ance used, and the numbers of sets and repetitions
completed. Record your weight and key body meas-
urements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
Q
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
R
S
C
D
E
T
F
M
N
U
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
G
H
I
V
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
W
X
J
K
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part from the PART LIST in the center of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If a part is not in the parts bag, check
to see if it has been pre-attached.
M6 x 38mm Screw (64)
M8 x 12mm Shoulder
M10 x 30mm Button Screw (56)
Bolt (57)
M10 x 45mm Button Bolt (74)
M8 x 58mm Button Bolt (71)
M10 x 25mm Button Screw (78)
1/4" x 9.5mm Allen
Head Set Screw (66)
M6 x 16mm Screw (63)
M4 x 16mm Screw (58)
M10 x 62mm Flat Head Screw (77)
1/4” x 14mm Button
Screw (59)
M6 x 63mm Screw (65)
M10 x 65mm Button Bolt (60)
M8 Nylon Locknut (72)
M10 Nylon Locknut (69)
M10 x 68mm Button Bolt (79)
M10 x 78mm Button Bolt (75)
M10 x 93mm Button Bolt (48)
M8 Washer (73)
M6 Washer (68)
M10 x 95mm Carriage Bolt (61)
M10 x 155mm Button Bolt (85)
M10 Washer (67)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFB38031
R1204A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
1
1
4
1
1
1
1
1
1
3
2
1
4
5
1
1
2
1
1
2
1
2
2
1
1
2
1
1
2
2
1
2
1
1
2
2
8
4
2
2
Bench Frame
Stabilizer
Bench Leg
Leg Lever
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
1
4
2
2
4
2
6
1
2
4
2
5
4
12
2
1
4
4
1
5
Curl Bar
M10 x 93mm Button Bolt
Weight Adapter
Pad Tube
Curl Post
Large Foam Pad
Small Foam Pad
19mm Square Inner Cap
Leg Lever Bushing
Top Bracket Bushing
M10 x 30mm Button Screw
M8 x 12mm Shoulder Bolt
M4 x 16mm Screw
1/4” x 14mm Button Screw
M10 x 65mm Button Bolt
M10 x 95mm Carriage Bolt
Right Upright
M6 x 16mm Screw
M6 x 38mm Screw
M6 x 63mm Screw
1/4” x 9.5mm Allen Head Set
Screw
Backrest Tube
Leg Lever Bracket
Adjustment Lever
Base Cap
Backrest Bracket
Weight Tube
Backrest
Seat
Curl Pad
Olympic Adapter
48mm Round Inner Cap
45mm Square Inner Cap
Notched Square Inner Cap
25mm Square Inner Cap
25mm Round Inner Cap
Handgrip
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Curl Knob
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
#
50
5
41
1
1
3
2
4
1
1
1
2
21
1
1
1
2
2
1
M10 Washer
M6 Washer
Small Round Bushing
25mm Round Outer Cap
10mm Spacer
M10 Nylon Jamnut
Center Base
Base
Rear Support
Crossbar
Left Upright
Guide Bar
Weight Bar
Locking Bar
Rack Foot
M10 Nylon Locknut
Thin Notched Square Inner Cap
M8 x 58mm Button Bolt
M8 Nylon Locknut
M8 Washer
M10 x 45mm Button Bolt
M10 x 78mm Button Bolt
“L”-bracket
M10 x 62mm Flat Head Screw
M10 x 25mm Button Screw
M10 x 68mm Button Bolt
Small Base Cap
Right Barbell Glider
Long Pad Tube
Top Bracket
Left Barbell Glider
Safety Spotter
Right Spotter Hook
Left Spotter Hook
Barbell Adapter
Weight Stop
Glider Bushing
Weight Bar Glider Bushing
Round Angled Bushing
48mm Tapered Inner Cap
Small Weight Clip
Large Weight Clip
M10 x 155mm Button Bolt
User’s Manual
Exercise Guide
1
1
1
3
#
#
#
Grease Pack
Allen Wrench
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. PFB38031
R1204A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-533-1333, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
1. The MODEL NUMBER of the product (PFB38031)
2. The NAME of the product (PROFORM C820 weight bench)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage
or repairs not provided by an ICON authorized service center; products used for commercial or rental pur-
poses; or products used as store display models. No other warranty beyond that specifically set forth above
is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 221330 R1204A
Printed in China © 2004 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|