This .pdf document is bookmarked
Operating Instructions and Parts Manual
10-inch Contractor Table Saw
Model 64B
Powermatic
427 New Sanford Road
LaVergne, Tennessee 37086
Ph.: 800-274-6848
Part No. M-1791229
Revision B 04/2014
Copyright © 2014 Powermatic
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 Table of contents
Section
Page
1.0 Warranty and Service.....................................................................................................................................2
2.0 Table of contents............................................................................................................................................3
3.0 Safety warnings..............................................................................................................................................4
3.1 Kickback.....................................................................................................................................................5
4.0 About this manual ..........................................................................................................................................6
5.0 Glossary.........................................................................................................................................................7
6.0 Features.........................................................................................................................................................8
7.0 Specifications.................................................................................................................................................8
8.0 Setup and Assembly ....................................................................................................................................10
8.1 Shipping contents.....................................................................................................................................10
8.2 Unpacking and cleanup............................................................................................................................11
8.3 Stand assembly........................................................................................................................................12
8.4 Mounting saw to stand .............................................................................................................................13
8.5 Installing handwheels/hooks ....................................................................................................................13
8.6 Installing table extensions ........................................................................................................................14
8.7 Leveling table extensions.........................................................................................................................14
8.8 Rails and Fence .......................................................................................................................................14
8.9 Wood Extension Table .............................................................................................................................14
8.10 Switch bracket........................................................................................................................................15
8.11 Motor cover ............................................................................................................................................15
8.12 Table insert.............................................................................................................................................15
8.13 Installing and removing blade.................................................................................................................15
8.14 Riving knife.............................................................................................................................................16
8.15 Blade guard ............................................................................................................................................16
9.0 Electrical connections ..................................................................................................................................16
9.1 Grounding instructions .............................................................................................................................16
9.2 Voltage conversion...................................................................................................................................17
9.3 Extension cords........................................................................................................................................17
9.4 Switch lockout ..........................................................................................................................................18
10.0 Adjustments ...............................................................................................................................................18
10.1 Fence alignment.....................................................................................................................................18
10.2 Blade raising/tilt mechanism...................................................................................................................18
10.3 Miter gauge ............................................................................................................................................18
10.4 Positive blade stops ...............................................................................................................................19
10.5 Riving knife alignment ............................................................................................................................20
10.6 Low profile riving knife............................................................................................................................20
10.7 Trunnion adjustment...............................................................................................................................20
10.8 Table to blade alignment ........................................................................................................................20
10.9 Belt tension and replacement.................................................................................................................21
11.0 Operations..................................................................................................................................................21
12.0 Safety devices............................................................................................................................................26
13.0 Maintenance...............................................................................................................................................27
14.0 Optional accessories..................................................................................................................................28
15.0 Troubleshooting the 64B Table Saw..........................................................................................................29
16.0 Replacement Parts.....................................................................................................................................29
16.1.1 Table and Cabinet Assembly – Exploded View...................................................................................30
16.1.2 Table and Cabinet Assembly – Parts List ...........................................................................................31
16.2.1 Motor and Trunnion Assembly – Exploded View.................................................................................32
16.2.2 Motor and Trunnion Assembly – Parts List .........................................................................................33
16.3.1 Stand Assembly – Exploded View.......................................................................................................35
16.3.2 Stand Assembly – Parts List ...............................................................................................................35
16.4.1 Blade Guard and Miter Gauge Assemblies – Exploded View .............................................................36
16.4.2 Blade Guard and Miter Gauge Assemblies – Parts List......................................................................37
17.0 Electrical Connections................................................................................................................................38
17.1 Connections for 115 volt (64B Table Saw)............................................................................................38
17.2 Connections for 230 volt (64B Table Saw)............................................................................................39
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Arsenic and chromium from chemically
treated lumber.
Your risk of exposure varies, depending on
how often you do this type of work. To reduce
your exposure to these chemicals, work in a
well-ventilated area and work with approved
safety equipment, such as face or dust masks
that are specifically designed to filter out
microscopic particles.
3.0 Safety warnings
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
12. Do not operate this machine while tired or
under the influence of drugs, alcohol or any
medication.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
13. Make certain switch is in the OFF position
before connecting machine to power supply.
3. Replace the warning labels if they become
obscured or removed.
14. Make certain the machine is properly
grounded.
4. This table saw is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a table saw, do
not use until proper training and knowledge
have been obtained.
15. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
16. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and
adjusting wrenches are removed from the
machine before turning it on.
5. Do not use this table saw for other than its
intended use. If used for other purposes,
Powermatic disclaims any real or implied
warranty and holds itself harmless from any
injury that may result from that use.
17. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
6. Always wear approved safety glasses/face
shields while using this table saw. Everyday
eyeglasses only have impact resistant lenses;
they are not safety glasses.
18. Check damaged parts. Before further use of
the machine, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
7. Before operating this table saw, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Remove all loose
clothing and confine long hair. Non-slip
footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Always use the blade guard on all ''through-
sawing''
operations.
A
through-sawing
operation is one in which the blade cuts
completely through the workpiece.
19. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
9. Kickback occurs when the workpiece is thrown
towards the operator at a high rate of speed. If
you do not have a clear understanding of
kickback and how it occurs, DO NOT operate
this table saw!
20. Keep the floor around the machine clean and
free of scrap material, oil and grease.
21. Keep visitors a safe distance from the work
area. Keep children away.
22. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
10. Wear ear protectors (plugs or muffs) during
extended periods of operation.
23. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in
serious injury.
11. Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contain chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
24. Maintain a balanced stance at all times so that
you do not fall into the blade or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and
other masonry products.
Download from Www.Somanuals.com. All Manuals Search And Download.
25. Use the right tool at the correct speed and
feed rate. Do not force a tool or attachment to
do a job for which it was not designed. The
right tool will do the job better and more safely.
Kickback Prevention
Tips to avoid the most common causes of
kickback:
26. Use recommended accessories; improper
accessories may be hazardous.
•
Make sure the riving knife is always aligned
with the blade. A workpiece can bind or stop
the flow of the cut if the riving knife is
misaligned, and result in kickback.
27. Maintain tools with care. Keep saw blades
sharp and clean for the best and safest
performance. Follow instructions for lubricating
and changing accessories.
•
•
Use a riving knife during every cut. The riving
knife maintains the kerf in the workpiece,
which will reduce the chance of kickback.
28. Turn off the machine before cleaning. Use a
brush or compressed air to remove chips or
debris — do not use your hands.
Never attempt freehand cuts. The workpiece
must be fed parallel to the blade, otherwise
kickback will likely occur. Always use the rip
fence or miter gauge to support the workpiece.
29. Do not stand on the machine. Serious injury
could occur if the machine tips over.
•
•
Make sure that rip fence is parallel to blade. If
not, the chances of kickback are very high.
Take the time to check and adjust the rip
fence.
30. Never leave the machine running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
31. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
Feed cuts through to completion. Anytime you
stop feeding a workpiece that is in the middle
of a cut, the chance of binding, resulting in
kickback, is greatly increased.
32. Keep hands out of the line of saw blade.
33. Use a push-stick when required.
Protection Tips from Kickback
34. Pay particular attention to instructions on
reducing risk of kickback.
Kickback can happen even if precautions are taken
to prevent it. Listed below are some tips to protect
you if kickback does occur:
35. Do not perform any operation freehand.
36. Never reach around or over saw blade.
•
•
•
•
Stand to the side of the blade when cutting. An
ejected workpiece usually travels directly in
front of the blade.
37. Don’t use in dangerous environment. Don’t
use power tools in damp or wet location, or
expose them to rain. Keep work area well
lighted.
Wear safety glasses or a face shield. Your
eyes and face are the most vulnerable part of
your body.
3.1 Kickback
Never place your hand behind the blade. If
kickback occurs, your hand will be pulled into
the blade.
The most common accidents among table saw
users, according to statistics, can be linked to
kickback, the high-speed expulsion of material from
the table that can strike the operator. Kickback can
also result in the operator’s hands being pulled into
the blade.
Use a push stick to keep your hands farther
away from the moving blade. If a kickback
occurs, the push stick will most likely take the
damage that your hand would have received.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
4.0 About this manual
This manual is provided by Powermatic covering the safe operation and maintenance procedures for a
Powermatic Model 64B Contractor Table Saw. This manual contains instructions on installation, safety
precautions, general operating procedures, maintenance instructions and parts breakdown. Your machine has
been designed and constructed to provide years of trouble-free operation if used in accordance with the
instructions as set forth in this document.
This manual is not intended to be an exhaustive guide to table saw operational methods, use of jigs or after-
market accessories, choice of stock, etc. Additional knowledge can be obtained from experienced users or
trade articles. Whatever accepted methods are used, always make personal safety a priority.
If there are questions or comments, please contact your local supplier or Powermatic. Powermatic can also be
Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.
Read and understand the entire contents of this manual before attempting assembly
or operation. Failure to comply may cause serious injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 Glossary
Arbor: Metal shaft that connects the drive
mechanism to the blade.
Parallel: Two lines or surfaces lying at equal
distance from each other at every point along their
lengths. For example, a rip fence must be parallel
to the side face of the saw blade.
Bevel Edge Cut: Tilt of the saw arbor and blade
between 0° and 45° to perform an angled cutting
operation.
Pawls, Anti-Kickback: Plates with a serrated
edge, usually mounted to the splitter, that prevent
the cut workpiece being drawn back toward the
blade and producing kickback.
Blade Guard: Mechanism mounted over the saw
blade to prevent accidental contact with the cutting
edge.
Perpendicular: 90° (right angle) intersection or
position of the vertical and horizontal planes such
as the position of the saw blade (vertical) to the
table surface (horizontal).
Crosscut: Sawing operation in which the miter
gauge is used to cut across the grain of the
workpiece.
Dado Blade: Blade used for cutting grooves and
rabbets. A stacked dado set can be used for wider
grooves.
Push Board/Push Stick: An instrument used to
safely push the workpiece through the cutting
operation.
Dado Cut: Flat bottomed groove in the face of the
workpiece made with a dado blade.
Rabbet: A cutting operation that creates an
L-shaped channel along the edge of the board.
Featherboard: Device used to keep a board
against the rip fence or table that allows the
operator to keep hands away from saw blade.
Resaw: Process of cutting a thick workpiece into
thinner pieces.
Rip Cut: A cut made along the grain of the
workpiece.
Freehand: Moving a workpiece into the blade
using only the hands, without a fixed positioning
device. (This is
a
dangerous, unacceptable
Riving Knife: A metal plate fixed relative to the
blade, which moves with the blade as cutting depth
is adjusted. Thus, it maintains not only the kerf
opening in the workpiece, but also the knife-to-
blade distance. A low-profile riving knife sits lower
than the top edge of the blade, and is used for non-
through cuts.
procedure – always use appropriate devices to
feed the workpiece though the saw blade during
cutting operations.)
Kerf: The resulting cut or gap made by a saw
blade.
Kerf, Standard: 1/8" gap made with a standard
blade.
Splitter (Spreader): A stationary metal plate to
which the blade guard is attached that maintains
the kerf opening in the workpiece when performing
a cutting operation. A splitter that rises and lowers
with the blade is called a riving knife.
Kickback: An event in which the workpiece is lifted
up and thrown back toward the operator, caused
when a workpiece binds on the saw blade or
between the blade and rip fence (or other fixed
object). To minimize or prevent injury from
kickbacks, see the Operations section.
Straightedge: A tool used to check that a surface
is flat or parallel.
Through Sawing: A sawing operation in which the
workpiece thickness is completely sawn through.
Proper blade height usually allows 1/8" of the top
of blade to extend above the wood stock. Keep the
blade guard down, the anti-kickback pawls down,
and the riving knife in place over the blade.
Miter Gauge: A component that controls the
workpiece movement while performing a crosscut
of various angles.
Non-Through Cut:
A
sawing operation that
requires the removal of the blade guard and
standard riving knife, resulting in a cut that does
not protrude through the top of the workpiece
(includes Dado and rabbet cuts).
The blade guard and riving knife must be re-
installed after performing a non-through cut to
avoid accidental contact with the saw blade during
operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 Features
Figure 1
1 – Cast iron table extensions
2 – T-slots
8 – Blade tilt angle scale
9 – Accu-Fence storage hook
3 – Transparent blade guard with riving knife
4 – Precision miter gauge with extension face
5 – Accu-Fence®
6 – Rail set (30” shown)
7 – Blade tilt handwheel (with lock knob)
10 – Adjustable foot pads
11 – Blade elevation handwheel (with lock knob)
12 – Miter gauge storage hook
13 – Industrial style push button switch
14 – Motor cover
7.0 Specifications
Model number ....................................................................................................................................................64B
Stock Numbers:
Model 64B basic saw – with stand, no fence or rails.................................................................................1791229
Model 64B basic saw – with 30” Rail Set, Accu-Fence®, 27”x17” Wood Extension Table .........................1791229K
Model 64B basic saw – with 50” Rail Set, Accu-Fence®, 27”x36” Wood Extension Table, Legs................1791230K
Materials:
Stand.............................................................................................................................................................steel
Saw body.......................................................................................................................................................steel
Tables...........................................................................................................................................ground cast iron
Handwheels............................................................................................................................................. cast iron
Trunnion .................................................................................................................................................. cast iron
Fence body................................................................................................................. steel with HDPE side plates
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor and Electricals:
Motor type.............................................................................. totally enclosed fan cooled, induction, capacitor start
Horsepower ...............................................................................................................................1-3/4 HP (1.3 kW)
Phase.......................................................................................................................................................... single
Voltage ......................................................................................................................... 115/230V (prewired 115V)
Cycle ........................................................................................................................................................... 60 Hz
Motor speed..........................................................................................................................................3450 RPM
Listed FLA (full load amps) ....................................................................................................................... 15/7.5 A
Starting amps..................................................................................................................................................52A
Running amps (no load) ....................................................................................................................................6A
Start capacitor............................................................................................................................ 400MFD 125VAC
Run capacitor....................................................................................................................................... 30μF 250V
Power transfer...............................................................................................................................................v-belt
On/off switch........................................................................................... manual industrial-style, with padlock hole
Power cord length ..............................................................................................................................7 ft. (213cm)
Power plug installed .........................................................................................................................................yes
Recommended circuit size1...................................................................................30A (for 115V) or 20A (for 230V)
Noise emission:
Without load........................................................................................................78 dB at 20 inches from blade
With load.............................................................................................................85 dB at 20 inches from blade
Arbor and blade:
Blade Diameter2 (in.) ..........................................................................................................................10” (254mm)
Arbor Diameter (in.).............................................................................................................................5/8” (16mm)
Arbor speed ..........................................................................................................................................3800 RPM
Arbor lock ........................................................................................................................................................yes
Maximum cut depth at 90 degrees ................................................................................................... 3-1/8” (79mm)
Maximum cut depth at 45 degrees ................................................................................................... 2-1/8” (54mm)
Maximum rip to right of blade................................................................................... 30” (762mm) or 50” (1270mm)
Maximum rip to left of blade................................................................................................................12” (305mm)
Dado maximum width....................................................................................................................13/16” (20.7mm
Dado maximum diameter..................................................................................................................... 8” (200mm)
Blade height per one revolution of handwheel .......................................... 5/32” (4mm) for 90°; 1/8” (2.9mm) for 45°
Blade tilt..............................................................................................................................................left, 0 to 45°
Table:
Table working surface .........................................................................................20-1/8” L x 27” W (511 x 686mm)
Table working surface, with extensions ..............................................................44-1/4” L x 27” W (1124 x 686mm)
Table working surface, with extensions and optional wood table:
With 30” rip capacity.....................................................................................71-1/4” L x 27” W (1810 x 686mm)
With 50” rip capacity.....................................................................................79-5/8” L x 27” W (2022 x 686mm)
Table area in front of blade at maximum height .............................................................................11-1/2” (292mm)
Table height from floor........................................................................................................................36” (914mm)
Miter slot..................................................................................................two T-slots, 3/4" W x 3/8” D (19 x 10mm)
Edge bevel..................................................................................................................................................... front
Dust collection:
Dust port outside diameter................................................................................................................... 4” (100mm)
Minimum extraction volume required..........................................................................................350 cfm (9.9 cmm)
Other:
Stand style.....................................................................................................................................................open
Stand footprint........................................................................................................21-1/2”L x24”W (546 x 610mm)
Overall Dimensions, shipping carton (basic saw only)..........................39” L x 25” W x 22” H (98.6 x 63.6 x 56.4cm)
Overall Dimensions, fully assembled, accessories mounted:
With 30” rip capacity...................................................................71-1/4” L x 43” W x 42” H (181 x 109 x 107cm)
With 50” rip capacity...................................................................79-5/8” L x 43” W x 42” H (202 x 109 x 107cm)
Weights:
Net................................................................................................................................................. 293 lb (133 kg)
Shipping......................................................................................................................................... 304 lb (138 kg)
1 subject to local and national electrical codes.
2 blade not included.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
8.0 Setup and Assembly
8.1 Shipping contents
(Figures 2 through 7)
1
2
1
2
2
2
1
2
4
1
1
1
1
1
1
Saw body with switch – A
Cast iron table extensions – B
Motor cover – C
Handwheels – D
Handwheel locking knobs – E
Handles – F
Arbor wrench – G
Open end wrenches (14-17, 10-12mm) – H
Hex keys (2.5/3/4/6mm) – I
Blade guard with anti-kickback pawls – J
Riving knife – K
Low profile riving knife – L
Miter gauge – M
Figure 2
Push stick – N
Table insert – O
1
Hardware package (p/n 64B-HP):
6
6
6
Hex cap screws M10x30 – HP-1
Lock washers 10mm – HP-2
Flat washers 10mm – HP-3
1
Stand assembly:
1
1
2
2
2
4
4
2
1
1
Upper brace, with cutout – P
Upper brace, long – Q
Upper braces, short – R
Lower braces, long – S
Lower braces, short – T
Legs – U
Figure 3
Foot pads – V
Fence hooks – W
Miter gauge hook – X
Small hook – Y
1
Stand hardware package (p/n 64B-SHP)
4
8
Hex cap screws M8x25 – SHP-1
Pan head screws M5x15 – SHP-2
Figure 4 – Hardware package (64B-HP)
24 Carriage bolts M8x16 – SHP-3
40 Flat washers 8mm – SHP-4
28 Lock washers 8mm – SHP-5
36 Hex nuts M8– SHP-6
8
Hex nuts M5 – SHP-7
1
1
Instructions and Parts Manual
Warranty Card
NOTE: The Accu-Fence, rail set, optional wood
extension table and legs, are all packaged
separately and supplied with their own hardware.
Figure 5 – Stand assembly
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6
Figure 7 – Stand hardware package (64B-SHP)
8.2 Unpacking and cleanup
Open shipping container and check for shipping
damage. Report any damage immediately to your
distributor and shipping agent. Do not discard any
shipping material until the Table Saw is assembled
and running properly.
Compare the contents of your container with the
previous list to make sure all parts are intact.
Missing parts, if any, should be reported to your
distributor. Read the instruction manual thoroughly
for assembly, maintenance and safety instructions.
Tools required for assembly (provided):
10, 12, 14 and 17 mm wrenches
Hex key set
Arbor wrench
Additional tools required (not supplied):
Cross point screwdriver
Rubber mallet or dead-blow hammer (or steel
hammer over a block of wood)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When stand has been assembled, turn it over
and install the rubber foot pads (V). (Should
you ever need height adjustment on the foot
pad, loosen the two hex nuts, rotate the pad,
then retighten the hex nuts against the metal
of the stand.)
8.3 Stand assembly
Assembly tip: A ratchet wrench with sockets and
extensions will speed assembly time.
1. Assemble stand, using Figure 8 as a guide.
Use the provided carriage bolts, flat washers
lock washers, and hex nuts (SHP-3/4/5/6).
4. Turn stand right-side up. The fasteners are not
fully tight, but they should be snug enough to
withstand the weight of the saw. If the stand
needs more stability, snug fasteners a little
more.
Only make fasteners snug at this time. They
will be fully tightened later, after stand has
settled under the weight of the saw.
5. The four large holes on top of the stand should
be reasonably aligned through the upper
braces for easy insertion of the screws.
2. Note the orientation of the cut-out brace (P) to
the front brace with Powermatic label (R). The
cut-out brace must be to the left, to allow
protrusion of the motor.
Figure 8
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 9
8.4 Mounting saw to stand
8.5 Installing handwheels/hooks
Refer to Figure 9
Refer to Figure 9.
1. Install a handwheel onto the tilting and raising
shafts, as shown. Fit the slot of the handwheel
onto the roll pin on the shaft, then secure by
screwing on the locking knob.
The table saw is heavy! Get
persons to assist you in lifting it. Failure to
comply may result in serious personal injury
and/or damage to the machine.
2. Install a handle onto each handwheel, using a
14mm wrench on the flat to tighten it.
1. Carefully lift table saw out of carton.
3. Install hooks (W and X) with two screws and
hex nuts (SHP-2/7). Placement is personal
preference, as all legs have holes for them.
2. Place table saw atop the stand, orienting the
motor in the cut-out of the stand, and aligning
the four holes on its bottom edge with those in
the stand.
NOTE: The two larger hooks will be on the
same side, to hold the fence. The smaller hook
holds the miter gauge.
3. Insert four screws, with flat washers, lock
washers and hex nuts (SHP-1/4/5/6), as
shown.
4. Mount small hook (Y) to the front, to hold
additional accessories such as arbor wrench,
push stick, riving knife, etc.
4. Securely tighten all four hex nuts (SHP-6),
using a 12mm wrench and an additional
wrench to hold the screw steady while
tightening the nut. (NOTE: If you need more
room to wrench the back screws, follow
instructions below for tilting motor out of the
way.)
5. Tilt arbor using right handwheel, and remove
Styrofoam packing from above motor.
5. Finish tightening all fasteners in the stand.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
8.6 Installing table extensions
Refer to Figure 10.
Figure 12
Figure 10
1. Start by tightening the three screws (17mm
wrench) under the table extension that secure
it to the saw table. Tighten these just enough
to hold the extension in place but loose
enough to change the extension height by
tapping on it.
1. Attach a table extension to the saw table.
Make sure edge bevel on table extension
faces front, to match that of saw table. Use
three screws, lock washers and flat washers
(HP-1/2/3). Lightly snug screws with 17mm
wrench.
2. Lay the straight edge (A, Figure 12) across the
saw table and extension, extending it out past
the edge of the extension as shown.
Assembly Tip: If you are doing this without an
assistant, lift table extension vertically to the
table edge. Install center screw and washer,
and make snug. Then pivot the extension
parallel to saw table to insert the other two
screws.
3. Move the straight edge to several places along
the table extension, as you continue to nudge
the extension level with the saw table. When
extension is level with saw table, securely
tighten each of the three screws.
2. Repeat for opposite table extension. Lightly
snug screws.
4. Repeat steps 1 through 3 for opposite table
extension.
3. The front edge of table extensions must be
flush with front edge of saw table. If needed,
tap front edge of extension with a rubber
mallet to make flush. See Figure 11.
8.8 Rails and Fence
With table extensions properly aligned, the rails
and Accu-Fence® assembly can now be mounted
to the saw. Consult the manual, no. M-2195075Z,
that accompanies the fence.
NOTE: The two tapped holes at the ends of the
table extensions are not used. There may be
additional holes in the table’s edge that are not
required for this rail installation.
8.9 Wood Extension Table
For instructions on mounting the accessory wood
extension table, consult your Accu-Fence®
manual, document no. M-2195075Z.
Figure 11
8.7 Leveling table extensions
Refer to Figure 12.
Level table extensions to saw table using a straight
edge. A metal straight edge is ideal, though a
carefully jointed board may also be used.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
between table and table insert, slightly raise that
area of the table insert above main table surface.
8.10 Switch bracket
Refer to Figure 13.
Remove existing screw and washers from the
farthest left hole on the guide tube, and use them
to secure the control switch to bottom of guide
tube, as shown in Figure 13 (10mm wrench).
Figure 15
8.13 Installing and removing blade
A blade is not provided with the 64B.
1. Using front handwheel, raise blade arbor fully
and tighten lock knob.
Figure 13
Refer to Figures 16 and 17.
8.11 Motor cover
2. Remove nut (A) and flange (B), and install
blade onto arbor, making sure the teeth point
downward toward front of saw.
Refer to Figure 14.
1. At the motor side, slide the hinge pins of the
motor cover down into the cylinders.
3. Install flange (B) and nut (A).
2. To secure cover, loosen knob (B), and swing
cover shut, while pushing in on the side. The
slot (C) should slide beneath the knob.
4. Rotate arbor until hole (C, Figure 17) aligns
with arbor lock pin (D). Push tab (E) to seat pin
into hole, and hold to prevent blade rotation.
3. Tighten knob (B).
5. Tighten nut (A) with arbor wrench.
6. Release arbor lock (E).
Figure 14
8.12 Table insert
Refer to Figure 15.
Place insert into table opening (the finger hole is
toward front of saw). Verify that insert lies flush
with table surface by resting a straight edge across
it at various points. If insert is not flush along its
length, turn any of six set screws (D) to raise or
lower that area of the insert.
Figure 16
NOTE: If while lowering blade, the points on the
anti-kickback pawls tend to catch in the seam
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Push guard down so that the pins slide into the
slots in the riving knife, then pull guard
backward to seat.
3. Secure with top latch (K).
4. The transparent guard leaves (L) should drop
freely to the table.
5. Lift the latch (J) to free the pawls. Pawls must
be lowered into operating position before using
the saw!
Figure 17
9.0 Electrical connections
8.14 Riving knife
Electrical connections must
Refer to Figure 18.
be made by
a
qualified electrician in
compliance with all relevant codes. This
machine must be properly grounded to help
prevent electrical shock and possible fatal
injury.
The saw is supplied with two riving knives: One
extends above the blade and accepts the blade
guard; the other is a low-profile knife that acts
alone for non-through cutting.
The 64B table saw is rated at 115/230V power, and
is pre-wired for 115 volt. The table saw comes with
a plug designed for use on a circuit with a
grounded outlet that looks like the one pictured in
A, Figure 19.
To install a riving knife:
1. Remove table insert, and raise arbor all the
way up.
2. Slide prongs of riving knife into slot between
block (F, Figure 18) and plate (G), and push
riving knife down as far as it will go.
Before connecting to power source, be sure switch
is in off position.
3. Push lever (H) downward, toward blade, until
tight.
It is recommended that the table saw, when
operated on 115 volt power, be connected to a
dedicated 30 amp circuit with a 30 amp circuit
breaker or time-delay fuse marked “D”. When
operated on 230 volt power, it is recommended
that the table saw be connected to a dedicated 20
amp circuit with a 20 amp circuit breaker or time-
4. The riving knife must be parallel to saw blade.
See section 10.5.
delay fuse marked “D”.
Local codes take
precedence over recommendations.
9.1 Grounding instructions
1. All Grounded, Cord-connected Tools:
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having
an equipment-grounding conductor and
a
grounding plug. The plug must be inserted into a
matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a
qualified electrician.
Figure 18
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor.
8.15 Blade guard
Refer to Figure 18.
1. Lift the anti-kickback pawls (I) and secure
them with the latch (J).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If repair or replacement of the electric cord or plug
is necessary, do not connect the equipment-
grounding conductor to a live terminal.
9.2 Voltage conversion
If 230V single phase operation is desired, follow
these instructions:
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
1. Disconnect table saw from power source.
2. Open the motor junction box, and consult the
diagram on the inside of the junction box
cover. Similar diagrams are shown in section
17.0.
Repair or replace damaged or worn cord
immediately.
NOTE: In case of discrepancy, the junction
box label takes precedence.
3. The four motor leads are connected for 115V
operation; reconnect these leads for 230V
operation, as shown in the diagrams.
4. The 115 volt attachment plug, supplied with
the saw, must be replaced with a UL/CSA
listed plug suitable for 230 volt operation.
Consult an electrician for proper procedures to
install the plug. The saw must comply with all
local and national codes after the 230 volt plug
is installed.
Figure 19
2. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating less
than 150 volts:
In all cases (115V or 230V) make certain the
receptacle in question is properly grounded. If
you are not sure, have a registered electrician
check the receptacle.
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in A, Figure
19. An adapter, shown in B and C, may be used to
connect this plug to a 2-pole receptacle as shown
in B if a properly grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet can be installed by a
qualified electrician. This adapter is not permitted
in Canada. The green-colored rigid ear, lug, and
the like, extending from the adapter must be
connected to a permanent ground such as a
properly grounded outlet box.
9.3 Extension cords
USE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When
using an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Table 1
shows correct size to use depending on cord
length and nameplate ampere rating. If in doubt,
use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
3. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating
between 150 - 250 volts, inclusive:
Ampere
Rating
Total length of
cord in feet
Volts
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in D, Figure
19. The tool has a grounding plug that looks like
the plug illustrated in D. Make sure the tool is
connected to an outlet having the same
configuration as the plug. No adapter is available
or should be used with this tool. If the tool must be
reconnected for use on a different type of electric
circuit, the reconnection should be made by
qualified service personnel; and after reconnection,
the tool should comply with all local codes and
ordinances.
120
240
25 50
50 100 200
100
150
300
Not
More
Than
More
Than
AWG
00
06
10
06
10
12
18 16
18 16
16 16
16
14
14
12
12
14
Not
12
16
14 12
Recommended
Extension Cord Recommendations
Table 1
Check with
a
qualified
electrician or service personnel if the
grounding instructions are not completely
understood, or if in doubt as to whether the
tool is properly grounded. Failure to comply
may cause serious or fatal injury.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
10.3 Miter gauge
Refer to Figure 22.
9.4 Switch lockout
The table saw is equipped with a push-button
switch that will accept a safety padlock, as shown
in Figure 20. To safeguard your machine from
unauthorized operation and accidental starting by
young children, the use of a padlock (not included)
is highly recommended. Place the key in a location
that is inaccessible to children and others not
qualified to use the tool.
10.3.1 Setting miter angle
The precision miter gauge has a rack and pinion
adjustment for setting the angle. To operate:
1. Slide miter gauge into one of the slots on table
top.
2. Loosen lock handle (A, Figure 22) by turning
counterclockwise.
3. Pull out spring-loaded knob (C) and rotate
knob until body (B) of miter gauge is at the
desired angle as indicated on the scale.
4. Tighten lock handle (A).
10.3.2 Indent settings
There are indents at the 0º, 30º and 45º right and
left positions. At these settings, release knob (C) to
engage stop rod. Then tighten lock handle (A).
Figure 20: Switch Lock Out
Note: Do not rely solely on the indents for an
accurate setting. After the stop rod engages at the
0º, 30º and 45º positions, make a fine adjustment
with the knob (C) if necessary, setting it against the
scale indicator (G).
10.0 Adjustments
10.1 Fence alignment
10.3.3 Extension plate
Before using the Accu-Fence®, verify that it is
properly aligned with the blade. Consult the
manual, no. M-2195075Z, that accompanied the
fence.
The extension plate (D, Figure 22) can be adjusted
by sliding to the right or left or removed entirely.
To adjust, loosen two lock handles (E), position the
extension plate and retighten lock handles. Make
sure end of extension plate is not in the blade’s
path.
10.2 Blade raising/tilt mechanism
Do not try to force tilting
mechanism past the 45º or 90º stops. This may
cause blade to go out of alignment.
NOTE: The lock handles (E) are adjustable. Pull
out on a handle, rotate it to different position, then
release, making sure it seats itself upon the pin.
Refer to Figure 21:
To remove extension plate, slide it completely off
and remove lock handles (E) and mounting
hardware.
To raise or lower blade, loosen lock knob (A) and
turn handwheel (B) on front of saw until desired
height is reached. Tighten lock knob. The blade
should be adjusted about 1/8" above top surface of
material being cut.
10.3.4 Calibration
1. Place miter gauge in one of the slots on the
table top.
To tilt blade, turn lock knob (C) counter-clockwise
to loosen, turn handwheel (D) until desired angle is
obtained, and retighten lock knob (C).
2. Set miter gauge at 90º to blade (0º setting on
the scale) by loosening lock handle (A), then
pulling out spring-loaded knob (C) and turning
the body (B) until 0º is indicated on scale.
3. Measure the accuracy of the gauge against
the slot with a combination square.
If adjustment is necessary:
4. Adjust body (B) until it is perfectly square (90º)
to miter slot.
5. Tighten lock handle (A).
6. Verify that scale indicator (G) reads 0º. If
Figure 21
further adjustment is needed:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Loosen screw (F) and adjust indicator (G) until
it reads 0º.
8. Tighten screw (F).
NOTE: The bar of the miter gauge has two slots
with set screws (H). Adjust these set screws (4mm
hex key) to eliminate any play between bar and
miter slot.
Figure 23
10.4.2 45° Blade stop
Repeat steps 1 through 4 above for 45° setting, as
shown in Figure 24. The 45° stop is shown at C,
Figure 25.
Figure 22
10.4 Positive blade stops
The stops for 90°, 45° blade tilt, and elevation
settings have all been factory set, and should
require no immediate adjustment. The settings
should be confirmed by the operator, however, and
especially if cuts become inaccurate.
10.4.1 90° Blade stop
1. Disconnect machine from power source.
Figure 24
2. Make sure table insert has been leveled with
table surface. See section 8.12.
3. Raise blade all the way, and place a 90°
square on the table and against the blade
(Figure 23). Make sure that a blade tooth does
not obstruct the actual reading.
4. Tilt blade with handwheel as needed until
square and blade are flush.
5. If adjustment is required, loosen the two
setscrews on 90° stop collar (A, Figure 25 –
3mm hex key) and rotate collar along the lead
screw to needed position. Verify the new
setting.
Figure 25
10.4.3 Blade elevation stops
6. Loosen screw on pointer (B, Figure 25), and
adjust pointer to zero. Retighten screw.
Lower blade all the way; it should drop completely
below the table surface. If it does not, adjust
amount of drop using two stop screws (D, Figure
26).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 26
Figure 28
10.5 Riving knife alignment
10.6 Low profile riving knife
The riving knife must be aligned with the blade for
proper and safe operation of the table saw. This
has been set by the manufacturer, but should be
verified by the operator.
A low profile riving knife is included with your saw.
It mounts and adjusts in the same manner as the
standard riving knife. The low profile riving knife
sits just below top of blade and is used for making
non-through cuts. The blade guard is not used with
this knife, so extra precautions should be taken
during operation.
1. Disconnect machine from power source.
2. Install riving knife and tighten lever (H, Figure
18).
3. Place a straight edge against blade and riving
knife; it should lie flush against both surfaces.
See Figure 27.
10.7 Trunnion adjustment
If backlash develops in the trunnion assembly, it
can be adjusted out using the screws (6mm hex
key) at front and back of cabinet (F, Figure 25
shows front screw). Front and rear trunnions
should receive the same amount of spring tension
from the screws.
4. If correction is needed, remove straight edge,
table insert, and riving knife and locate four set
screws (E, Figure 28) through the corner holes
of clamp block.
5. Rotate any of the four set screws as needed to
tilt the angle of the clamp block, and thus the
riving knife.
10.8 Table to blade alignment
Refer to Figures 29 and 30.
6. Install riving knife and verify the setting with
the straight edge. Make further adjustments as
needed.
The table has been squared to the blade by the
manufacturer and no adjustment is necessary now.
If cuts become inaccurate, check table-blade
squareness and correct if necessary. Use the miter
slot to do this:
1. Disconnect saw from power source.
2. Raise blade to maximum height.
3. Mark one tooth (A, Figure 29) with a grease
pencil and position the tooth slightly above the
top edge of table at the front.
4. Raise the miter gauge slightly out of its slot to
serve as a shoulder. Using a sliding square (B)
against the side of the bar, slide the scale over
until it touches the tip of the blade, and lock
the scale in position.
Figure 27
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Loosen screw (A) and hex nut (B) and pivot
motor upward to release tension on belt. If
greater movement is needed, remove screw
(A) and pivot motor further.
2. Replace belt.
3. Reinstall screw (A) and push down on motor to
tension new belt.
4. Tighten screw (A) and hex nut (B).
Figure 29
Figure 31
Figure 30
11.0 Operations
5. Rotate marked tooth (A) so that it is slightly
above table top at the rear and, using the
square as before, verify that the distance to
the blade is the same. See Figure 30. If the
distances are not the same, make a careful
note of the difference.
NOTE: If the saw is to be used without the metal
stand provided, care must be taken to provide a
hole in the stand or bench used by the operator to
facilitate removal of sawdust.
If there is any tendency to
slide, walk, or tip over during operation, the
stand or bench MUST be secured to the floor.
6. Loosen table screws (item #30, section
16.1.1), and nudge table according to the
distance you noted.
Familiarize yourself with the location and operation
of all controls and adjustments and the use of
accessories such as miter gauge and rip fence.
7. Retighten screws firmly.
8. Verify the alignment, angle pointer setting,
fence setting, etc. Make any needed
adjustments.
11.1 Start/stop switch
This table saw has a manual
switch. If the power goes out during operation,
push the STOP button. Otherwise, the saw will
start up when power is restored.
10.9 Belt tension and replacement
Tension of the drive belt should be inspected after
the first few days of operation, as it may stretch
slightly during initial use; also inspect it periodically
thereafter.
11.2 Kickback prevention
To tighten belt:
Serious injury can result from kickbacks which
occur when a workpiece binds on the saw blade or
binds between the blade and rip fence or other
fixed object. This binding can cause the workpiece
to lift up and be thrown toward the operator.
1. Disconnect machine from power source.
2. Loosen screw (A, Figure 31) and hex nut (B,
Figure 31).
3. Press down on motor while retightening screw
(A) and hex nut (B).
Listed below are conditions which can cause
kickbacks:
If belt shows signs of wear, fraying, cracks, etc. it
should be replaced:
ˆ
Confining the cutoff piece when
crosscutting or ripping.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ
ˆ
Releasing the workpiece before
completing operation or not pushing work
piece all the way past saw blade.
Not using the splitter/riving knife when
ripping or not maintaining alignment of the
splitter/riving knife with the saw blade.
Using a dull saw blade.
Not maintaining alignment of the rip fence
so that it tends to angle toward rather than
away from the saw blade front to back.
Applying feed force when ripping to the
cutoff (free) section of the workpiece
instead of the section between saw blade
and fence.
narrow (6" width or less), or thin work. Use
a push block or miter gauge hold-down
when dadoing or molding.
Never use the fence as a length stop
when crosscutting. Do not hold or touch
the free end or cutoff section of a
workpiece. On through-sawing operations,
the cutoff section must NOT be confined.
Always keep your hands out of line of the
saw blade and never reach back of the
cutting blade with either hand to hold the
workpiece.
Bevel ripping cuts should always be made
with the fence on the right side of saw
blade so that the blade tilts away from the
fence and minimizes the possibility of the
work binding and the resulting kickback.
ˆ
ˆ
ˆ
ˆ
ˆ
ˆ
ˆ
Ripping wood that is twisted (not flat), or
does not have a straight edge, or has
twisted grain.
To minimize or prevent injury from kickbacks:
11.3 Rip sawing
ˆ
ˆ
Avoid conditions listed above.
Wear a safety face shield, goggles, or
Ripping is where the workpiece is fed with the grain
into the saw blade using the fence or other
positioning device as a guide to ensure desired
width of cut (Figure 33).
glasses.
ˆ
Do not use the miter gauge and rip fence
in the same operation unless provision is
made by use of a facing board on the
fence so as to allow the cutoff section of
the workpiece to come free before the
actual cut begins (See Figure 39).
As the machine receives use, the
operation of the anti-kickback pawls
should be checked periodically (Figure
32). If the pawls do not stop the reverse
motion of a workpiece, resharpen all the
points.
Before starting a ripping cut,
verify that fence is clamped securely and
aligned properly.
ˆ
ˆ
ˆ
ˆ
Never rip freehand or use miter gauge in
combination with the fence.
Never rip workpieces shorter than the saw
blade diameter.
Never reach behind the blade with either
hand to hold down or remove the cutoff
piece with the saw blade rotating.
Figure 32
ˆ
ˆ
Where possible, keep your face and body
out of line with potential kickbacks
including when starting or stopping the
machine.
Dull, badly set, improper, or improperly
filed cutting tools, and cutting tools with
gum or resin adhering to them can cause
accidents. Never use a cracked saw
blade. The use of a sharp, well
Figure 33
Always use blade guard, splitter/riving knife and
anti-kickback pawls. Make sure splitter/riving knife
is properly aligned. When wood is cut along the
grain, the kerf tends to close and bind on the blade
and kickbacks can occur.
maintained, and correct cutting tool for the
operation will help avoid injuries.
ˆ
Support the work properly and hold it
firmly against gauge or fence. Use a push
stick or push block when ripping short,
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 34
The rip fence (A, Fig. 34) should be set for the
width of the cut by using the scale on the front rail,
or by measuring the distance between blade (A)
and fence (B). Stand out of line with saw blade and
workpiece to avoid sawdust and splinters coming
off the blade or a potential kickback.
Figure 36
When ripping long boards, use a support at front of
table (C, Figure 36), such as a roller stand, and a
support or "tailman" at the rear (D).
If the work piece does not have a straight edge,
nail an auxiliary straight edged board on it to
provide one against the fence. To cut properly, the
board must make good contact with the table. If it
is slightly warped, turn the hollow side down. Do
not attempt to cut boards with significant warp.
Never use the rip fence beyond the point where the
carriage is flush with the end of the rails.
Have the blade extend about 1/8" above the top of
the workpiece. Exposing the blade above this point
can be hazardous.
In ripping, use one hand to hold the board down
against the fence or fixture, and the other to push it
into the blade between blade and fence. If
workpiece is narrower than 6" or shorter than 12",
use a push stick or push block to push it through
between fence and blade (Figure 35). Never push
in a location such that the pushing hand is in line
with the blade. Move the hand serving as a hold-
down a safe distance from blade as cut nears
completion.
11.4 Resawing
Resawing is a ripping operation in which thick
boards are cut into thinner ones. Note: A band saw
is the ideal tool for resawing.
If the table saw is used for
resawing, take precautions such as using an
auxiliary fence, resaw barrier or similar devices
to stabilize the workpiece and provide operator
safety.
For very narrow ripping where a push stick cannot
be used, use a push block or auxiliary fence.
Always push the workpiece completely past the
blade at the end of a cut to minimize the possibility
of a kickback.
Narrow boards up to 3" can be resawn in one pass.
Wider boards up to 6" must be resawn in two
passes.
In resawing wider boards, adjust the blade height
so as to overlap the two cuts by 1/2" as shown in
Figure 37. Too deep a first cut can result in binding
and possible kickbacks on the second cut. Always
use the same side of the board against the fence
for both cuts.
Figure 35
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not crosscut workpieces shorter than 6". Before
starting a cut, be sure the miter gauge is securely
clamped at the desired angle. Hold the workpiece
firmly against the table and back against the miter
gauge. Always use the saw guard and riving knife
and make sure the riving knife is properly aligned.
For 90 degree crosscutting, most operators prefer
to use the left-hand miter gauge slot. When using it
in this position, hold the workpiece against the
gauge with the left hand and use the right hand to
advance the workpiece. When using the right hand
slot for miter and compound crosscutting so that
the blade tilts away from the gauge, the hand
positions are reversed.
When using the miter gauge, the workpiece must
be held firmly and advanced smoothly at a slow
rate. If the workpiece is not held firmly, it can
vibrate causing it to bind on the blade and dull the
saw teeth.
Figure 37
11.5 Crosscutting
Crosscutting is where the workpiece is fed cross
grain into the saw blade using the miter gauge to
support and position the workpiece (Figure 38).
Figure 40
Figure 38
To augment the effectiveness of the miter gauge in
crosscutting, some users mount an auxiliary
wooden extension face (F, Figure 40) with a glued-
on strip of sandpaper (G) to the miter gauge.
Crosscutting should never be done freehand nor
should the fence be used as an end stop unless an
auxiliary block (E, Figure 39) is clamped to the
front of the blade area such that the cutoff piece
comes free of the block before cutting begins.
Provide auxiliary support for any workpiece
extending beyond the table top with a tendency to
sag and lift up off the table.
Have the blade extend about 1/8" above the top of
the workpiece. Exposing the blade above this point
can be hazardous.
11.6 Bevel and miter operations
Bevel cut – A bevel cut is a special type of
operation where the saw blade is tilted at an angle
less than 90 degrees to the table top (Figure 41).
Operations are performed in the same manner as
ripping or crosscutting, except the fence or miter
gauge should be used on the right-hand side of the
blade to provide added safety in avoiding a binding
action between blade and table top. When beveling
with the miter gauge, the workpiece must be held
firmly to prevent creeping.
Figure 39
Length stops should not be used on the free end of
the workpiece in the cutoff area.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The process of cutting 1/8" to 13/16" grooves in
workpieces is accomplished by the use of a
stacked dado blade set or an adjustable type blade
mounted on the saw arbor. By using various
combinations of stacked dado blades, or properly
setting the dial on an adjustable blade, an accurate
width dado can be made. This is very useful for
shelving, making joints, tenoning, etc.
The guard, riving knife, and anti-kickback pawls
supplied with the saw should be used for all cutting
operations where they can be used. When
performing operations where the guard cannot be
used, as in some dadoing operations, alternative
safety precautions should be taken. These include
push sticks, feather boards, filler pieces, fixtures,
jigs and any other appropriate device that can be
utilized to keep operators’ hands away from the
blade. Upon completion of the operation requiring
removal of the guard, the entire guard assembly
must be placed back on the machine in its proper
working order.
Figure 41
Mitering – Crosscuts made at an angle to the edge
of the workpiece are called miters (Figure 42). Set
the miter gauge at the required angle, and make
the cut the same as a normal crosscut except the
workpiece must be held extra firmly to prevent
creeping.
Never use a dado head in a
tilted position. Never operate the saw without
the blade guard, riving knife and anti-kickback
pawls for operations where they can be used.
Figure 42
Note: When making compound miters (with blade
tilted) use the miter gauge in the right hand slot to
provide more hand clearance and safety.
Have the blade extend only 1/8" above the top of
the workpiece. Exposing the blade above this point
can be hazardous.
11.7 Dado cutting
Dadoing is cutting a wide groove into a workpiece
or cutting a rabbet along the edge of a workpiece.
A dado insert (optional accessory, not provided)
shown in Figure 43, is necessary for this type of
operation.
Do not use the standard table
insert for dadoing operations.
Figure 43
25
Download from Www.Somanuals.com. All Manuals Search And Download.
12.0 Safety devices
Feather board
Feather boards can be purchased at most tool
stores, or made by the operator to suit particular
applications. The feather board (Figure 44) should
be made of straight grain hardwood approximately
1" thick and 4" to 8" wide depending on the size of
the machine. The length is developed in
accordance with intended use.
Feather boards can be fastened to the table or rip
fence by use of C-clamps. Alternatively, drilled and
tapped holes in the table top allow the use of wing
nuts and washers as a method of clamping. If this
method of fastening is used, provide slots in the
feather board for adjustment. (The illustration
shows a method of attaching and use of the
feather board as a vertical comb. The horizontal
application is essentially the same except that the
attachment is to the table top.)
Figure 45 – Filler Piece
Push stick and push block
The use of a push block or push stick provides an
added level of safety for the operator. A push stick
is included with your table saw, but you may wish
to make others personalized for different cutting
procedures. The templates in Figures 46 and 47
offer construction details.
Figure 46 – Push Block Template
Figure 44
Filler piece
A filler piece (Figure 45) is necessary for narrow
ripping and permits the blade guard to remain on
the machine. It also provides space for the safe
use of a push stick.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ
ˆ
Wipe down table surface and T-slots, and
apply a rust preventive to them.
Clean pitch and resin from saw blade.
Weekly:
ˆ
ˆ
Clean motor housing with compressed air.
Wipe down fence rails with a dry silicon
lubricant.
Lubrication
Refer to Figure 48.
Lower the arbor all the way, and lubricate the
following elements with a lithium grease every 12
months, or more frequently if needed. Clean the
elements first with a solvent/degreaser and a soft
rag.
ˆ
ˆ
Blade angling trunnions (A, Figure 48).
Wipe a light coat of grease on the
elevating rods (B).
ˆ
ˆ
Threads of blade elevating screw (C)
Threads of blade tilting screw (D).
Raise and lower arbor, and tilt it back and forth, to
distribute the grease.
Check all adjustments after lubricating.
Figure 47 – Push stick template
Figure 48
13.0 Maintenance
Miscellaneous
Always be aware of the condition of your machine.
Routinely check the condition of the following items
and repair or replace as necessary:
Always disconnect power to
the machine before performing maintenance.
Failure to do this may result in serious
personal injury.
ˆ
ˆ
ˆ
ˆ
ˆ
Mounting bolts (tighten)
Power switch
Saw blade (cracks, worn or dull teeth, etc.)
Blade guard and riving knife
Drive belt (cracks, frays, worn areas, etc.)
Cleaning
Clean the table saw according to the schedule
below to ensure maximum performance. The
schedule assumes the saw is being used every
day.
Daily:
27
Download from Www.Somanuals.com. All Manuals Search And Download.
14.0 Optional accessories
These accessory items, purchased separately, can
enhance the functionality of your table saw.
Contact your dealer to order, or call Powermatic at
the phone number on the cover.
p/n 1791088 – Dado insert for 64B table saw
p/n 708118 – Universal mobile base
Figure 49
28
Download from Www.Somanuals.com. All Manuals Search And Download.
15.0 Troubleshooting the 64B Table Saw
Table 2
Trouble
Probable Cause
Remedy
No incoming power.
Fuse blown, or circuit breaker tripped.
Cord damaged.
Check all plug connections.
Replace fuse, or reset circuit breaker.
Replace cord.
Table saw will not start.
Tilting or raising lock knobs not tightened.
Tighten lock knobs on handwheels.
Adjust foot pad(s). If saw is secured to
floor, use shims as needed.
Replace blade.
Machine not resting evenly on floor.
Blade out of balance.
Excessive vibration.
Check motor pulley and spindle pulley.
Tighten set screws if needed.
Replace belt.
Have motor checked by a qualified
inspector. Repair or replace.
Re-set stops and pointer on gauge.
(Section 10.3).
Pulley loose.
Belt is worn, cracked or frayed.
Motor not functioning properly.
Miter gauge out of adjustment.
Cuts out-of-square
when crosscutting.
Miter slot misaligned.
Excessive feed.
Realign table to blade (Section 10.8).
Reduce feed.
Replace blade; use proper type of blade
for cut needed.
Dull or incorrect blade.
Miter slot misaligned.
Fence misaligned.
Motor stalls or
workpiece binds or
burns.
Realign table to blade (Section 10.8).
Realign fence (see Accu-Fence®
manual).
Have motor checked by a qualified
inspector. Repair or replace.
Motor malfunction.
Cuts not true at 90 or 45
degrees.
Stop screws not set properly.
Lock knob not released.
Readjust screws (Section 10.4).
Loosen lock knob.
Tilting or Raising
handwheel difficult to
turn.
Worm and worm gear segment caked with Clean and regrease worm and worm gear
sawdust and pitch.
segment.
Worm and worm gear segment out of
alignment.
Realign worm with segment.
Identify and correct overload condition,
e.g. excessive feed rate of stock.
Clean sawdust from fan and duct areas of
motor.
Motor overloaded.
Motor overheats
Improper cooling of motor; lack of air
circulation.
Request voltage check from power
company and correct low voltage
condition.
Replace centrifugal switch (qualified
personnel only).
Have motor checked by a qualified
inspector. Repair or replace.
Correct overload condition.
Increase supply wire size.
Request voltage check from power
company and correct low voltage
condition.
Low voltage.
Motor starts slowly or
fails to come up to full
speed.
Centrifugal switch not operating.
Motor malfunction.
Power line overloaded.
Undersized wires in supply system.
Motor fails to develop
full power.
Low voltage.
Have motor checked by a qualified
inspector. Repair or replace.
Motor malfunction.
16.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-
Model Number and Serial Number of your machine available when you call will allow us to serve you quickly
and accurately.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
16.1.1 Table and Cabinet Assembly – Exploded View
30
Download from Www.Somanuals.com. All Manuals Search And Download.
16.1.2 Table and Cabinet Assembly – Parts List
Index No Part No Description
Size
Qty
1 ................64B-101..................... Table........................................................................ ......................................1
2 ................64B-102..................... Table Extension....................................................... ......................................2
..................64B-TIA..................... Table Insert Assembly (#3 thru #4).......................... ......................................1
3 ................64B-103..................... Table Insert.............................................................. ......................................1
4 ................TS-1522011 .............. Socket Set Screw .................................................... M5x5 .............................6
5 ................64B-105..................... Cover ....................................................................... ......................................1
6 ................3520B-126................. Handle ..................................................................... ......................................1
7 ................64B-107..................... Handwheel............................................................... ......................................1
8 ................64B-108..................... Cover Plate.............................................................. ......................................1
9 ................64B-109..................... Lead Screw.............................................................. ......................................1
10 ..............64B-110..................... Angle Scale.............................................................. ......................................1
11 ..............BB-6201ZZ................ Ball Bearing ............................................................. 6201ZZ..........................1
12 ..............64B-112..................... Cabinet .................................................................... ......................................1
13 ..............TS-1523021 .............. Socket Set Screw .................................................... M6x8 .............................4
14 ..............TS-1523011 .............. Socket Set Screw .................................................... M6x5 .............................4
15 ..............64B-115..................... Bushing.................................................................... ......................................2
16 ..............64B-116..................... Bushing.................................................................... ......................................2
17 ..............64B-117..................... Spring Pin................................................................ Ø4x25 mm ....................1
18 ..............TS-1540061 .............. Hex Nut.................................................................... M8.................................2
19 ..............TS-2361081 .............. Lock Washer............................................................ M8.................................6
20 ..............TS-1550061 .............. Flat Washer ............................................................. M8.................................6
21 ..............TS-1504071 .............. Socket Head Cap Screw.......................................... M8x35 ...........................2
22 ..............64B-122..................... Spring Pin................................................................ Ø3x12 mm ....................2
23 ..............64B-123..................... Lock Bushing ........................................................... ......................................1
24 ..............64B-124..................... Lock Knob................................................................ ......................................1
25 ..............LM000636 ................. Warning Label.......................................................... ......................................1
26 ..............6290630 .................... Strain Relief ............................................................. 7W-2 .............................3
27 ..............TS-1550031 .............. Flat Washer ............................................................. M5.................................1
28 ..............64B-128..................... Lock Knob................................................................ ......................................1
29 ..............64B-129..................... I.D label.................................................................... ......................................1
30 ..............TS-1490031 .............. Hex Cap Screw........................................................ M8x20 ...........................4
31 ..............TS-1491041 .............. Hex Cap Screw........................................................ M10x30 .........................6
32 ..............TS-2361101 .............. Lock Washer............................................................ M10...............................6
33 ..............TS-1550071 .............. Flat Washer ............................................................. M10...............................6
34 ..............64B-134..................... Power Cord.............................................................. ......................................1
35 ..............64B-135..................... Motor Cord............................................................... ......................................1
36 ..............TS-081C082.............. Phillips Pan Head Machine Screw........................... #10-24x1-1/2”................2
37 ..............6296133 .................... Switch Push Button.................................................. ......................................1
38 ..............6291367 .................... Switch Bracket......................................................... ......................................1
39 ..............TS-0733031 .............. Star Washer............................................................. #10................................2
40 ..............6296128 .................... Switch...................................................................... ......................................1
41 ..............6291366 .................... Switch Box............................................................... ......................................1
42 ..............TS-0560071 .............. Hex Nut.................................................................... #10-24...........................2
43 ..............TS-1533032 .............. Phillips Pan Head Machine Screw........................... M5x10 ...........................2
44 ..............TS-0733041 .............. Star Washer............................................................. 1/4"................................2
45 ..............TS-1540031 .............. Hex Nut.................................................................... M5.................................2
46 ..............TS-0720071 .............. Lock Washer............................................................ 1/4"................................1
47 ..............TS-0050031 .............. Hex Cap Screw........................................................ 1/4"-20x3/4” ..................1
48 ..............JPS10TSR-103......... Push Block............................................................... ......................................1
49 ..............6290642 .................... Arbor Wrench........................................................... ......................................1
50 ..............JBOS5-105................ Open End Wrench................................................... #14-#17.........................1
51 ..............JBOS5-106................ Open End Wrench................................................... #10-#12.........................1
52 ..............TS-152707 ................ Hex Key................................................................... 6mm..............................1
53 ..............TS-152705 ................ Hex Key................................................................... 4mm..............................1
54 ..............TS-152704 ................ Hex Key................................................................... 3mm..............................1
55 ..............JPS10TSR-105......... Hex Key................................................................... 2.5mm...........................1
..................64B-HP...................... Hardware Package (includes #31-33) ..................... ......................................1
31
Download from Www.Somanuals.com. All Manuals Search And Download.
16.2.1 Motor and Trunnion Assembly – Exploded View
32
Download from Www.Somanuals.com. All Manuals Search And Download.
16.2.2 Motor and Trunnion Assembly – Parts List
Index No Part No Description
Size
Qty
1 ................64B-124..................... Lock Knob................................................................ ......................................1
2 ................3520B-126................. Handle ..................................................................... ......................................1
3 ................64B-107..................... Handwheel............................................................... ......................................1
4 ................64B-117..................... Spring Pin................................................................ Ø4x25 mm ....................1
5 ................64B-205..................... Lead Screw.............................................................. ......................................1
6 ................64B-206..................... Thrust Bearing ......................................................... 51104............................1
7 ................64B-207..................... Bushing.................................................................... ......................................1
8 ................TS-154012 ................ Hex Nut.................................................................... M20-2.5P ......................1
9 ................64B-209..................... Bushing.................................................................... ......................................1
10 ..............64B-210..................... Spacer ..................................................................... ......................................1
11 ..............TS-1522031 .............. Socket Set Screw .................................................... M5x10 ...........................2
12 ..............TS-0267041 .............. Socket Set Screw .................................................... 1/4”-20x3/8”...................4
13 ..............64B-213..................... Gear......................................................................... ......................................2
14 ..............64B-214..................... Pointer ..................................................................... ......................................1
15 ..............TS-1533052 .............. Phillips Pan Head Machine Screw........................... M5x15 ...........................8
16 ..............64B-216..................... Lock Washer............................................................ ......................................2
17 ..............64B-217..................... Guide Shaft.............................................................. ......................................1
18 ..............TS-1541031 .............. Nylon Lock Hex Nut................................................. M8.................................1
19 ..............64B-219..................... Bearing .................................................................... ......................................1
20 ..............64B-220..................... Gear Cover .............................................................. ......................................1
21 ..............TS-1532042 .............. Phillips Pan Head Machine Screw........................... M4x12 ...........................3
22 ..............TS-1550021 .............. Flat Washer ............................................................. M4.................................3
23 ..............64B-223..................... Poly-V Belt............................................................... 188J..............................1
24 ..............64B-224..................... Socket Head Cap Screw.......................................... M8x65 ...........................1
25 ..............TS-1550061 .............. Flat Washer ............................................................. M8.................................2
26 ..............64B-226..................... Spring ...................................................................... ......................................1
27 ..............64B-227..................... Trunnion................................................................... ......................................2
28 ..............TS-1491031 .............. Hex Cap Screw........................................................ M10x25 .........................4
29 ..............TS-2361101 .............. Lock Washer............................................................ M10...............................4
30 ..............64B-230..................... Center Trunnion....................................................... ......................................1
31 ..............64B-231..................... Screw....................................................................... ......................................1
32 ..............64B-232..................... Support Base........................................................... ......................................1
33 ..............TS-1482031 .............. Hex Cap Screw........................................................ M6x16 ...........................2
34 ..............TS-1550041 .............. Flat Washer ............................................................. M6.................................2
35 ..............64B-235..................... Cover ....................................................................... ......................................1
36 ..............TS-1550031 .............. Flat Washer ............................................................. M5.................................5
37 ..............6290693 .................... Arbor Nut ................................................................. ......................................1
38 ..............6290598 .................... Flange...................................................................... ......................................1
39 ..............64B-239..................... Arbor........................................................................ ......................................1
40 ..............64B-240..................... Clamp ...................................................................... 3”...................................2
41 ..............64B-241..................... Hose ........................................................................ ......................................1
42 ..............64B-242..................... Nut ........................................................................... ......................................1
43 ..............64B-243..................... Lock Handle............................................................. ......................................1
44 ..............64B-244..................... Bolt........................................................................... ......................................1
45 ..............64B-245..................... Holding Plate ........................................................... ......................................1
46 ..............TS-1524011 .............. Socket Set Screw .................................................... M8x8 .............................4
47 ..............64B-247..................... Support Base........................................................... ......................................1
48 ..............64B-248..................... Low Profile Riving Knife........................................... ......................................1
49 ..............TS-1550041 .............. Flat Washer ............................................................. M6.................................1
50 ..............64B-250..................... Bolt........................................................................... ......................................1
51 ..............64B-251..................... Spring ...................................................................... ......................................1
52 ..............64B-252..................... Moving Rod.............................................................. ......................................2
53 ..............TS-1504041 .............. Socket Head Cap Screw.......................................... M8x20 ...........................2
54 ..............TS-1504071 .............. Socket Head Cap Screw.......................................... M8x35 ...........................2
55 ..............64B-255..................... S-Ring...................................................................... S15................................1
56 ..............64B-256..................... Bushing.................................................................... ......................................2
57 ..............64B-257..................... Lead Screw.............................................................. ......................................1
58 ..............64B-258..................... Thrust Bearing ......................................................... ......................................1
59 ..............64B-259..................... Ball Bearing ............................................................. 6202-5/8” bore ..............2
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Index No Part No
Description
Size
Qty
60 ..............64B-260..................... Shaft ........................................................................ ......................................1
61 ..............64B-261..................... Bracket..................................................................... ......................................1
62 ..............64B-262..................... Bearing .................................................................... ......................................4
63 ..............64B-263..................... Thread Housing ....................................................... ......................................1
64 ..............64B-264..................... Bushing.................................................................... ......................................1
65 ..............6290630 .................... Strain Relief ............................................................. 7W-2 .............................1
66 ..............64B-266..................... Hex Nut (L.H Thread) .............................................. M14-2.0P ......................1
67 ..............64B-267..................... Key........................................................................... 5x5x25 mm ...................1
68 ..............64B-268..................... Motor Pulley............................................................. ......................................1
69 ..............64B-269..................... Plate......................................................................... ......................................1
70 ..............TS-2361051 .............. Lock Washer............................................................ M5.................................2
71 ..............TS-1523031 .............. Socket Set Screw .................................................... M6x10 ...........................2
72 ..............64B-272..................... Motor........................................................................ ......................................1
..................64B-272MF ............... Motor Fan (not shown)............................................. ......................................1
..................64B-272MFC............. Motor Fan Cover (not shown).................................. ......................................1
..................64B-272CS................ Centrifugal Switch (not shown)................................ ......................................1
..................64B-272SCC............. Starting Capacitor Cover (not shown)...................... ......................................1
..................64B-272RCC............. Running Capacitor Cover (not shown)..................... ......................................1
..................64B-272SC................ Starting Capacitor (not shown) ................................ 400MFD, 125VAC.........1
..................64B-272RC ............... Running Capacitor (not shown) ............................... 30μf, 250VAC ...............1
..................64B-272JB ................ Junction Box (not shown) ........................................ ......................................1
..................64B-272JBC.............. Junction Box Cover (not shown).............................. ......................................1
..................64B-272OL................ Overload (not shown) .............................................. ......................................1
..................64B-272DC ............... Dust Cover (not shown)........................................... ......................................1
73 ..............TS-1550071 .............. Flat Washer ............................................................. M10...............................1
74 ..............TS-1491031 .............. Hex Cap Screw........................................................ M10x25 .........................1
75 ..............TS-0680081 .............. Flat Washer ............................................................. 5/8”................................1
76 ..............64B-276..................... Nylon Lock Hex Nut................................................. 5/8”-11...........................1
77 ..............TS-1482061 .............. Hex Cap Screw........................................................ M6x30 ...........................2
78 ..............TS-2311061 .............. Hex Nut.................................................................... M6.................................2
..................64B-ALA.................... Arbor Lock Assembly (82# thru 88#) ....................... ......................................1
79 ..............TS-1502041 .............. Socket Head Cap Screw.......................................... M5x16 ...........................2
80 ..............TS-2361051 .............. Lock Washer............................................................ M5.................................2
81 ..............TS-1550031 .............. Flat Washer ............................................................. M5.................................2
82 ..............64B-282..................... Bracket..................................................................... ......................................1
83 ..............64B-283..................... Spring Pin................................................................ Ø3x25 mm ....................1
84 ..............64B-284..................... Lock Shaft................................................................ ......................................1
85 ..............64B-285..................... Spring ...................................................................... ......................................1
86 ..............TS-1550061 .............. Flat Washer ............................................................. M8.................................1
87 ..............64B-287..................... Handle ..................................................................... ......................................1
88 ..............TS-1541001 .............. Hex Nylon Lock Nut................................................. M4.................................1
34
Download from Www.Somanuals.com. All Manuals Search And Download.
16.3.1 Stand Assembly – Exploded View
16.3.2 Stand Assembly – Parts List
Index No Part No
Description
Size
Qty
1 ................64B-301..................... Leg........................................................................... ......................................4
2 ................64B-302..................... Upper Side Brace .................................................... ......................................1
3 ................64B-303..................... Upper Short Brace................................................... ......................................2
4 ................64B-304..................... Upper Long Brace.................................................... ......................................1
5 ................64B-305..................... Lower Short Brace (includes stripe)......................... ......................................2
6 ................64B-306..................... Lower Long Brace (includes stripe) ......................... ......................................2
7 ................64B-307..................... Powermatic Nameplate Label.................................. 1-1/2”W x 10”L ..............1
8 ................64B-308..................... Miter Gauge Hook.................................................... ......................................1
9 ................64B-309..................... Fence Body Hook .................................................... ......................................2
10 ..............64B-310..................... Hook ........................................................................ ......................................1
11 ..............64B-311..................... Rubber Foot Pad ..................................................... ......................................4
12 ..............64B-312..................... Carriage Bolt............................................................ M8x16 .........................24
13 ..............TS-1550061 .............. Flat Washer ............................................................. M8...............................40
14 ..............TS-2361081 .............. Lock Washer............................................................ M8...............................28
15 ..............TS-1540061 .............. Hex Nut.................................................................... M8...............................36
16 ..............TS-1533052 .............. Phillips Pan Head Machine Screw........................... M5x15 ...........................8
17 ..............TS-1540031 .............. Hex Nut.................................................................... M5.................................8
18 ..............TS-1490041 .............. Hex Cap Screw........................................................ M8x25 ...........................4
..................64B-SHP................... Stand Hardware Package (#12 thru #18) ................ ......................................1
..................3520B-158................. Black Stripe.............................................................. ...............................per ft.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
16.4.1 Blade Guard and Miter Gauge Assemblies – Exploded View
36
Download from Www.Somanuals.com. All Manuals Search And Download.
16.4.2 Blade Guard and Miter Gauge Assemblies – Parts List
Index No Part No Description
Size
Qty
..................64B-BGA................... Blade Guard Assembly (#1 thru #31) ...................... ......................................1
1 ................64B-401..................... Riving Knife.............................................................. ......................................1
..................64B-UGA................... Upper Guard Assembly (#2 thru #31)...................... ......................................1
2 ................64B-402..................... Support Arm............................................................. ......................................1
3 ................64B-403..................... Left side Blade Guard.............................................. ......................................1
4 ................64B-404..................... Right Side Blade Guard........................................... ......................................1
5 ................64B-405..................... Plate......................................................................... ......................................1
6 ................64B-406..................... Anti-Kickback Pawl.................................................. ......................................2
7 ................64B-407..................... Spring ...................................................................... ......................................1
9 ................TS-1533032 .............. Phillips Pan Head Machine Screw........................... M5x10 ...........................2
10 ..............TS-0640071 .............. Nylon Lock Hex Nut................................................. 1/4”-20...........................8
11 ..............TS-0813051 .............. Flat Head Screw...................................................... 1/4”-20x5/8”...................8
12 ..............TS-0680021 .............. Flat Washer ............................................................. 1/4”................................8
13 ..............64B-413..................... Spring Pin................................................................ Ø6x30 mm ....................1
14 ..............64B-414..................... Spring Pin................................................................ Ø3.5x28 mm .................2
15 ..............64B-415..................... Spring Pin................................................................ Ø5x35 mm ....................1
17 ..............64B-417..................... Shaft ........................................................................ ......................................1
18 ..............64B-418..................... Holding Bracket ....................................................... ......................................1
19 ..............TS-1541021 .............. Nylon Lock Hex Nut................................................. M6.................................2
20 ..............TS-1482071 .............. Hex Cap Screw........................................................ M6x35 ...........................1
21 ..............64B-421..................... Lock Handle............................................................. ......................................1
22 ..............64B-422..................... Holding Bracket ....................................................... ......................................1
24 ..............64B-424..................... Front Shield ............................................................. ......................................1
25 ..............TS-1502021 .............. Socket Head Cap Screw.......................................... M5x10 ...........................2
26 ..............64B-426..................... Pivot Arm ................................................................. ......................................4
27 ..............64B-427..................... Warning Label.......................................................... ......................................1
28 ..............TS-1481081 .............. Hex Cap Screw........................................................ M5x35 ...........................1
29 ..............TS-1550031 .............. Flat Washer ............................................................. M5.................................1
30 ..............64B-430..................... Bushing.................................................................... ......................................2
31 ..............TS-1541011 .............. Nylon Lock Hex Nut................................................. M5.................................1
..................1791789 .................... Miter Gauge Assembly (#32 thru #52)..................... ......................................1
32 ..............PM2000-323.............. Miter Gauge Body.................................................... ......................................1
33 ..............PM2000-324.............. Pin............................................................................ ......................................1
34 ..............PM2000-325.............. Miter Bar .................................................................. ......................................1
35 ..............PM2000-326.............. Guide Washer.......................................................... ......................................1
36 ..............PM2000-327.............. Flat Head Machine Screw........................................ M6x9 .............................1
37 ..............TS-0050051 .............. Hex Cap Screw........................................................ 1/4”-20x1”......................2
38 ..............PM2000-329.............. Socket Head Cap Screw.......................................... M5x8 .............................2
39 ..............PM2000-330.............. Support Base........................................................... ......................................1
40 ..............PM2000-331.............. Knob ........................................................................ ......................................1
41 ..............TS-1521011 .............. Socket Set Screw .................................................... M4x4 .............................1
42 ..............PM2000-333.............. Locking Handle........................................................ ......................................2
43 ..............TS-0810012 .............. Phillips Pan Head Machine Screw........................... #10-24x1/4”...................1
44 ..............PM2000-335.............. Pointer ..................................................................... ......................................1
45 ..............PM2000-336.............. Spring ...................................................................... ......................................1
46 ..............PM2000-337.............. Gear Shaft ............................................................... ......................................1
47 ..............PM2000-338.............. Scale........................................................................ ......................................1
48 ..............PM2000-339.............. Rivet......................................................................... ......................................2
49 ..............PM2000-340.............. Handle ..................................................................... ......................................1
50 ..............TS-0680031 .............. Flat Washer ............................................................. 5/16”..............................1
51 ..............PM2000-342.............. Fence....................................................................... ......................................1
52 ..............PM2000-343.............. Socket Set Screw .................................................... M8x6 .............................2
37
Download from Www.Somanuals.com. All Manuals Search And Download.
17.0 Electrical Connections
17.1 Connections for 115 volt (64B Table Saw)
400MFD 125 VAC
30uf 250 VAC
115V
38
Download from Www.Somanuals.com. All Manuals Search And Download.
17.2 Connections for 230 volt (64B Table Saw)
400MFD 125 VAC
30uf 250 VAC
230V
39
Download from Www.Somanuals.com. All Manuals Search And Download.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Pelco Home Security System CC1400HZ16 2 User Manual
Philips Bottle Warmer SCF276 16 User Manual
Philips CD Player AZ8051 User Manual
Philips Network Card Network Adaper User Manual
Philips Refrigerator 19PFL3404D 05 User Manual
Philips Switch SWV2052W User Manual
Pioneer Bluetooth Headset BDP 31FD User Manual
Pioneer DVD Recorder DVR 420H User Manual
Powermate Portable Generator PM0603250 User Manual
Precor Treadmill M945i User Manual