Poulan Trimmer TE 450 User Manual

R
Please do not return unit to retailer.  
Por favor, no devuelva el aparato al lugar de compra.  
Veuillez ne pas retourner l’outil au détaillant.  
1-800-554-6723  
Operator’s Manual  
Manual del Operador  
Manuel de L’utilisateur  
t
TWIST--N--EDGE  
TE 450  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual del operador y siga todas las advertencias e instruc-  
ciones de seguridad. El no hacerlo puede resultar en lesiones gra-  
ves.  
AVERTISSEMENT:  
Lire le manuel de l’utilisateur et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le  
faire pourrait entraîner des blessures graves.  
Electrolux Home Products, Augusta, GA 30907  
WCI Outdoor Products, Inc.  
530087982  
10/5/00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Always store gasoline in a container ap-  
loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek med-  
ical attention. An anti-vibration system does  
not guarantee the avoidance of these prob-  
lems. Users who operate power tools on a  
continual and regular basis must monitor  
closely their physical condition and the condi-  
tion of this tool.  
proved for flammable liquids.  
CUTTING SAFETY  
WARNING: Inspect the area before  
each use. Remove objects (rocks, broken  
glass, nails, wire, etc.) which can be thrown  
by or become entangled in line. Hard objects  
can damage trimmer head and be thrown  
causing serious injury.  
ASSEMBLY  
S Use only for trimming, mowing, edging and  
sweeping. Do not use for pruning or hedge  
trimming.  
WARNING: Make sure your unit is  
properly assembled and all fasteners are se-  
cure.  
S Keep firm footing and balance. Do not over-  
reach.  
S Keep all parts of your body away from spin-  
ning line and muffler. Keep engine below  
waist level. A hot muffler can cause serious  
burns.  
ATTACHING THE HANDLE  
S Cutting with the line on left side of the shield  
will throw debris away from the operator.  
S Use only in daylight or good artificial light.  
TRANSPORTING AND STORAGE  
S Allow the engine to cool; secure unit before  
storing or transporting in vehicle.  
Groove  
S Empty the fuel tank before storing or trans-  
porting the unit. Use up fuel left in the car-  
buretor by starting the engine and letting it  
run until it stops.  
S Assemble handle to the unit as shown;  
make sure bottom of handle is seated in the  
groove in the trigger housing.  
S Store unit and fuel in an area where fuel va-  
pors cannot reach sparks or open flames  
from water heaters, electric motors or  
switches, furnaces, etc.  
S Store unit so line limiter cannot accidentally  
cause injury. Unit can be hung by the tube.  
S Store the unit out of the reach of children.  
If situations occur which are not covered in this  
manual, use care and good judgment. If you  
need assistance, call 1--800--554--6723.  
NOTE: Wing nut must be assembled on the  
side of the unit opposite the operators posi-  
tion.  
S Pivot handle to a comfortable position.  
Tighten handle securely.  
ATTACHING THE SHIELD  
WARNING: The shield must be prop-  
erly installed. The shield provides partial  
protection from the risk of thrown objects to  
the operator and others and is equipped with  
a line limiter blade which cuts excess line to  
the proper length. The line limiter blade (on  
underside of shield) is sharp and can cut you.  
S Remove wing nut from shield.  
SPECIAL NOTICE: This unit is not  
equipped with a temperature limiting muffler  
and spark arresting screen which meets the  
requirements of California Codes 4442 and  
4443. All U.S. forest land and the states of  
California, Idaho, Maine, Minnesota, New  
Jersey, Oregon, and Washington require by  
law that many internal combustion engines to  
be equipped with a spark arrestor screen. If  
you operate in a locale where such regula-  
tions exist, you are legally responsible for  
installing and maintaining the operating con-  
dition of these parts. Failure to do so is a viola-  
tion of the law. If a spark arrestor is required  
in your area, contact your Authorized Service  
Dealer for the proper kit.  
S Insert bracket into slot as shown.  
S Pivot shield until bolt passes through hole  
in bracket.  
S Securely tighten wing nut onto bolt.  
Slot  
Shield  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or ab-  
normal swellings. Prolonged use in cold  
weather has been linked to blood vessel dam-  
age in otherwise healthy people. If symptoms  
occur such as numbness, pain, loss of  
strength, change in skin color or texture, or  
Bracket  
Wing  
Nut  
Line Limiter Blade  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING YOUR UNIT  
FUEL YOUR UNIT  
This engine is certified to operate on un-  
leaded gasoline. Gasoline must be mixed  
with a good quality 2-cycle air-cooled engine  
oil designed to be mixed at a ratio of 40:1.  
OPERATING POSITION  
ALWAYS WEAR:  
Eye  
Protection  
Poulan/Weed Eaterr  
brand oil is recom-  
mended. (A 40:1 ratio is obtained by mixing  
3.2 ounces of oil with 1 gallon of unleaded  
gasoline). When mixing fuel follow the  
instructions printed on the container. Always  
read and follow the safety rules under FUEL  
SAFETY.  
Long Pants  
Heavy Shoes  
Cut from your right to your left.  
STARTING  
ADVANCING THE CUTTING LINE  
Advance line by tapping the bottom of the cut-  
ting head lightly on the ground while engine is  
running at full speed. A metal blade attached  
to the shield will cut the line to the proper  
length.  
For occasional use only.  
Starting Position  
TWIST--N--EDGE  
S Pull the tab toward the engine.  
S Twist the tube to the edging position;  
release the tab.  
HOW TO STOP YOUR UNIT  
Push and hold engine stop switch in the STOP  
position until the unit has fully stopped.  
Choke lever  
Muffler  
Trigger  
REPLACING THE LINE  
S Remove spool by firmly pulling on tap but-  
ton.  
Primer Bulb  
S Clean entire surface of hub and spool.  
S Replace with a pre-wound spool, or cut a  
length of 20 feet of .080” (2 mm) diameter  
Poulan/Weed Eaterr brand line. Never use  
wire, rope, string, etc., which can break off  
and become a dangerous missile.  
S Insert one end of the line about 1/2 inch (1  
cm) into the small hole on the inside of  
spool.  
HOW TO START YOUR UNIT  
WARNING: The trimmer head will  
turn while starting the engine. A hot muffler  
can cause serious burns.  
STARTING A COLD ENGINE (or a  
warm engine after running out of  
fuel)  
S Set unit on a flat surface.  
Small  
Hole  
S Slowly press the primer bulb 6 times.  
S Move choke lever to FULL CHOKE posi-  
tion.  
Spool  
S Squeeze the throttle trigger fully and hold  
through all remaining steps.  
S Pull starter rope handle sharply 6 times.  
S Move choke lever to HALF CHOKE posi-  
tion.  
Line in Notch  
S Pull starter rope handle no more than 6  
pulls, until engine runs.  
S Allow engine to run 10 seconds, then move  
choke lever to OFF CHOKE position.  
RESTARTING A WARM ENGINE  
S Move choke lever to OFF CHOKE position.  
S Pull starter rope handle until engine runs.  
S If engine does not start in 5 pulls, follow  
instructions in STARTING A COLD EN-  
GINE.  
Hub  
Line exit hole  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Wind the line evenly and tightly onto the  
spool. Wind in the direction of the arrow  
found on the spool.  
SERVICE  
We recommend all service and adjustments  
not listed in this manual be performed by an  
Authorized Service Dealer.  
S Push the line into the notch, leaving 3 to 5  
inches (7 -- 12 cm) unwound.  
S Insert the line into the the exit hole in the hub  
as shown in the illustration.  
CARBURETOR ADJUSTMENTS  
Your carburetor is equipped with limiter caps.  
Carburetor adjustment is a complicated task.  
We recommend that you take your unit to an  
Authorized Service Dealer. Damage will oc-  
cur if you turn the needles beyond the limiter  
stops.  
S Align the notch with the line exit hole.  
S Push spool into hub until it snaps into place.  
S Pull the line extending outside of the hub to  
release it from the notch.  
IGNITION TIMING  
The ignition timing is fixed, non-adjustable.  
SPARK PLUG  
Replace the spark plug yearly using a Cham-  
pion RCJ--8Y plug. Spark plug gap is 0.025”.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing any of the  
recommended remedies below other than remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
S See “Starting.”  
Engine will not S Engine flooded.  
S Fill tank with correct fuel mixture.  
S Install new spark plug.  
S Fuel tank empty.  
S Spark plug not firing.  
S Fuel not reaching carburetor.  
start.  
S Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
S See “Carburetor Adjustments.”  
S Carburetor requires adjustment.  
Engine will not S Carburetor requires adjustment. S See “Carburetor Adjustments.”  
S Throttle trigger screw too  
tight.  
S Loosen screw.  
idle properly.  
Engine will not S Air filter dirty.  
S Clean or replace air filter.  
S Spark plug fouled.  
S Clean or replace spark plug; re-gap.  
accelerate,  
lacks power,  
or dies under  
a load.  
S Carburetor requires adjustment. S See “Carburetor Adjustments.”  
Engine  
S Fuel mixture incorrect.  
S Empty fuel tank and refill with  
correct fuel mixture.  
smokes  
S Air filter dirty.  
S Clean or replace air filter.  
excessively.  
S Carburetor requires adjustment. S See “Carburetor Adjustments.”  
Line does not  
advance or  
breaks while  
cutting.  
S Check line routing.  
S Line improperly routed in head.  
S Line improperly wound on  
spool.  
S Rewind line tightly and evenly.  
S Use only 0.065” (1.65 mm) dia. line.  
S Line size incorrect.  
S Use only 0.065” (1.65 mm) dia. line.  
S Replace with correct spool.  
S Cut with tip of line fully extended.  
Line welds  
onto spool.  
S Line size incorrect.  
S Incorrect spool.  
S Line is being crowded against  
material being cut.  
S Remove spool and pull 4 inches  
(10 cm) of line outside of head.  
S Use only 0.065” (1.65 mm) dia. line.  
Line pulls  
back into  
head.  
S Too little line outside of head.  
S Line size incorrect.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
this warranty does not cover tune-ups, spark  
plugs, filters, starter ropes, starter springs,  
cutting line, or rotating head parts that will  
wear and require replacement with reason-  
able use during the warranty period. This war-  
ranty does not cover predelivery setup or nor-  
mal adjustments explained in the operators  
manual.  
NEED ASSISTANCE?  
Need Assistance?  
Call 1-800-554-6723.  
Need Service Parts?  
Contact your dealer .  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, Div.  
WCI Outdoor Products, Inc. warrants to the  
original purchaser that each new Poulan  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
brand gasoline tool or attachment is free from AND THERE ARE NO OTHER EXPRESS  
defects in material and workmanship and WARRANTIES EXCEPT THOSE EX-  
agrees to repair or replace under this war-  
ranty any defective gasoline product or at-  
PRESSLY STIPULATED HEREIN.  
tachment as follows from the original date of SOME STATES DO NOT ALLOW LIMITA-  
purchase.  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CON-  
SEQUENTIAL DAMAGES, SO THE ABOVE  
2 YEARS-- Parts and Labor, when used for  
household purposes.  
90 DAYS -- Parts and Labor, when used for  
commercial, professional, or income produc- LIMITATIONS OR EXCLUSION MAY NOT  
ing purposes.  
APPLY TO YOU.  
30 DAYS -- Parts and Labor, if used for rental  
purposes.  
ELECTROLUX HOME PRODUCTS’ policy  
This warranty is not transferable and does not is to continuously improve its products.  
cover damage or liability caused by improper Therefore, ELECTROLUX HOME PROD-  
handling, improper maintenance, or the use UCTS reserves the right to change, modify, or  
of accessories and/or attachments not spe- discontinue models, designs, specifications,  
cifically recommended by ELECTROLUX  
and accessories of all products at any time  
HOME PRODUCTS for this tool. Additionally, without notice or obligation to any purchaser.  
U.S. EPA / ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
part will be repaired or replaced by POULAN/  
LIGATIONS: The U. S. Environmental  
WEED EATER. OWNER’S WARRANTY  
Protection Agency/Environment Canada and RESPONSIBILITIES: As the lawn and gar-  
POULAN/WEED EATER, DIVISION OF WCI  
OUTDOOR PRODUCTS are pleased to ex-  
plain the emissions control system warranty  
den equipment engine owner, you are re-  
sponsible for the performance of the required  
maintenance listed in your Owner’s Manual.  
on your lawn and garden equipment engine. POULAN/WEED EATER recommends that  
All new utility and lawn and garden equipment you retain all receipts covering maintenance  
engines must be designed, built, and on your lawn and garden equipment engine,  
equipped to meet the stringent anti--smog but POULAN/WEED EATER cannot deny  
standards. POULAN/WEED EATER must  
warrant the emission control system on your  
warranty solely for the lack of receipts or for  
your failure to ensure the performance of all  
lawn and garden equipment engine for the pe- scheduled maintenance. As the lawn and  
riods of time listed below provided there has garden equipment engine owner, you should  
been no abuse, neglect, or improper mainte- be aware that POULAN/WEED EATER may  
nance of your lawn and garden equipment en- deny you warranty coverage if your lawn and  
gine. Your emission control system includes  
parts such as the carburetor and the ignition  
garden equipment engine or a part of it has  
failed due to abuse, neglect, improper mainte-  
system. Where a warrantable condition exits, nance, unapproved modifications, or the use  
POULAN/WEED EATER will repair your lawn  
and garden equipment engine at no cost to equipment manufacturer. You are responsi-  
you. Expenses covered under warranty in- ble for presenting your lawn and garden  
clude diagnosis, parts and labor. MANUFAC- equipment engine to a POULAN/WEED EAT-  
TURER’S WARRANTY COVERAGE: If any  
ER authorized repair center as soon as a  
emissions related part on your engine (as problem exists. Warranty repairs should be  
of parts not made or approved by the original  
listed under Emissions Control Warranty  
completed in a reasonable amount of time,  
Parts List) is defective or a defect in the mate- not to exceed 30 days. If you have any ques-  
rials or workmanship of the engine causes the tions regarding your warranty rights and re-  
failure of such an emission related part, the sponsibilities, you should contact your near-  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
est authorized service center or call  
able for damages to other engine  
components caused by the failure of a war-  
ranted part still under warranty. WHAT IS  
NOT COVERED: All failures caused by  
POULAN/WEED  
1--800--554--6723.  
EATER  
at  
WARRANTY COM-  
MENCEMENT DATE: The warranty period  
begins on the date the lawn and garden equip- abuse, neglect, or improper maintenance are  
ment engine is purchased. LENGTH OF  
not covered. ADD--ON OR MODIFIED  
PARTS: The use of add--on or modified parts  
COVERAGE: This warranty shall be for a pe-  
riod of two years from the initial date of pur- can be grounds for disallowing a warranty claim.  
chase. WHAT IS COVERED: REPAIR OR  
POULAN/WEED EATER is not liable to cover  
failures of warranted parts caused by the use  
REPLACEMENT OF PARTS. Repair or re-  
placement of any warranted part will be per- of add--on or modified parts. HOW TO FILE A  
formed at no charge to the owner at an ap- CLAIM: If you have any questions regarding  
proved POULAN/WEED EATER servicing  
center. If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized ser-  
your warranty rights and responsibilities, you vice center or call POULAN/WEED EATER at  
should contact your nearest authorized ser- 1--800--554--6723 . WHERE TO GET WAR-  
vice center or call POULAN/WEED EATER at  
RANTY SERVICE: Warranty services or re-  
pairs shall be provided at all POULAN/WEED  
1--800--554--6723 WARRANTY PERIOD:  
Any warranted part which is not scheduled for EATER service centers. call: 1--800--554--6723  
replacement as required maintenance, or MAINTENANCE, REPLACEMENT AND RE-  
which is scheduled only for regular inspection  
to the effect of “repair or replace as neces-  
sary” shall be warranted for 2 years. Any war-  
ranted part which is scheduled for replace-  
PAIR OF EMISSION RELATED PARTS: Any  
POULAN/WEED EATER approved replace-  
ment part used in the performance of any war-  
ranty maintenance or repair on emission re-  
ment as required maintenance shall be lated parts will be provided without charge to  
warranted for the period of time up to the first the owner if the part is under warranty. EMIS-  
scheduled replacement point for that part. SION CONTROL WARRANTY PARTS  
DIAGNOSIS: The owner shall not be  
LIST: Carburetor, Ignition System: Spark  
charged for diagnostic labor which leads to Plug (covered up to maintenance schedule),  
the determination that a warranted part is de- Ignition Module. MAINTENANCE STATE-  
fective if the diagnostic work is performed at MENT: The owner is responsible for the per-  
an approved POULAN/WEED EATER serv-  
icing center. CONSEQUENTIAL DAM-  
AGES: POULAN/WEED EATER may be li-  
formance of all required maintenance as de-  
fined in the owner’s manual.  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Stereo Amplifier CS 800S User Manual
Philips Breast Pump SCF660 04 User Manual
Philips CD Player PSA615 User Manual
Philips Digital Camera SPC1030NC 27 User Manual
Philips Electric Shaver QT4060 User Manual
Philips Telephone Accessories SDJ6060W User Manual
Philips TV Cables SWA2416W User Manual
Polaroid Digital Camera i1035 User Manual
Poulan Snow Blower PP165E30 User Manual
Praktica Digital Camera D00390 User Manual