Poulan Trimmer 530088147 User Manual

R
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
031  
For Occasional Use Only  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en le-  
siones graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le  
faire pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
250 Bobby Jones Expressway  
Augusta, GA 30907  
Copyright E2002 Electrolux Home Products, Inc.  
530088147  
4/24/02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or abnor-  
mal swellings. Prolonged use in cold weather  
has been linked to blood vessel damage in  
otherwise healthy people. If symptoms occur  
such as numbness, pain, loss of strength,  
change in skin color or texture, or loss of feeling  
in the fingers, hands, or joints, discontinue the  
use of this tool and seek medical attention. An  
anti--vibration system does not guarantee the  
avoidance of these problems. Users who oper-  
ate power tools on a continual and regular basis  
must monitor closely their physical condition  
and the condition of this tool.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equipped with a spark arresting screen. If you  
operate in a locale where such regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of these parts. Failure  
to do so is a violation of the law. For normal  
homeowner use, the muffler and spark arrest-  
ing screen will not require any service. After  
50 hours of use, we recommend that your  
muffler be serviced or replaced by an autho-  
rized service dealer.  
CUTTING SAFETY  
WARNING: Inspect the area before  
each use. Remove objects (rocks, broken  
glass, nails, wire, etc.) which can be thrown  
by or become entangled in line. Hard objects  
can damage the trimmer head and be thrown  
causing serious injury.  
S Use only for trimming, scalping, mowing and  
sweeping. Do not use for edging, pruning or  
hedge trimming.  
S Keep firm footing and balance. Do not over-  
reach.  
S Keep all parts of your body away from muffler  
and spinning line. Keep engine below waist  
level. A hot muffler can cause serious burns.  
S Cut from your left to your right. Cutting on  
right side of the shield will throw debris away  
from the operator.  
S Use only in daylight or good artificial light.  
S Use only for jobs explained in this manual.  
TRANSPORTING AND STORAGE  
S Allow engine to cool before storing or trans-  
porting in vehicle.  
S Empty the fuel tank before storing or trans-  
porting the unit. Use up fuel left in the carbu-  
retor by starting the engine and letting it run  
until it stops.  
S Store unit and fuel in area where fuel vapors  
cannot reach sparks or open flames from  
water heaters, electric motors or switches,  
furnaces, etc.  
S Store unit so line limiter blade cannot acci-  
dentally cause injury. The unit can be hung  
by the tube.  
S Store unit out of reach of children.  
ASSEMBLY  
ATTACHING SHIELD  
WARNING: If received assembled,  
repeat all steps to ensure your unit is properly  
assembled and all fasteners are secure.  
WARNING: The shield must be prop-  
erly installed. The shield provides partial protec-  
tion to the operator and others from the risk of  
thrown objects, and is equipped with a line limit-  
er blade which cuts excess line to the proper  
length. The line limiter blade (on underside of  
shield) is sharp and can cut you.  
Examine parts for damage. Do not use dam-  
aged parts.  
NOTE: If you need assistance or find parts  
missing or damaged, call 1-800-554-6723.  
For proper orientation of shield, see KNOW  
YOUR TRIMMER illustration in OPERATION  
section.  
It is normal for the fuel filter to rattle in the  
empty fuel tank.  
Finding fuel or oil residue on muffler is normal  
due to carburetor adjustments and testing  
done by the manufacturer.  
1. Remove wing nut from shield.  
2. Insert bracket into slot as shown.  
3. Pivot shield until bolt passes through hole  
in bracket.  
ADJUSTING THE HANDLE  
4. Securely tighten wing nut onto bolt.  
Slot  
WARNING: When adjusting the han-  
dle, be sure it remains between the trigger  
and the safety decal.  
Shield  
Bracket  
1. Loosen handle by turning T--handle/  
screw counterclockwise.  
2. Rotate the handle on the tube to an upright  
position.  
3. Adjust handle to a comfortable position  
between the trigger and the safety label  
on the tube.  
Wing  
nut  
4. Retighten handle by turning T--handle/  
screw clockwise.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
NIT.  
ntrols  
ON/STOP SWITCH  
CHOKE  
The ON/STOP switch is used to stop the  
engine. To stop the engine, push and release  
the engine ON/STOP switch.  
The CHOKE helps to supply fuel to the engine  
to aid in cold starting. Activate the choke by  
moving the choke lever to the FULL CHOKE  
position. After the engine attempts to start, move  
the choke lever to the HALF CHOKE position.  
Once engine has started, move the choke lever  
to the OFF CHOKE position.  
PRIMER BULB  
The PRIMER BULB removes air from the car-  
buretor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate the primer  
bulb by pressing it and allowing it to return to  
its original form.  
follow the safety rules relating to fuel before  
fueling your unit.  
BEFORE STARTING ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you be-  
gin. If you do not understand the safety rules,  
do not attempt to fuel your unit. Call  
1-800-554--6723.  
IMPORTANT  
Experience indicates that alcohol blended  
fuels (called gasohol or using ethanol or  
methanol) can attract moisture which leads to  
separation and formation of acids during stor-  
age. Acidic gas can damage the fuel system  
of an engine while in storage.  
FUELING ENGINE  
To avoid engine problems, empty the fuel sys-  
tem before storage for 30 days or longer.  
Drain the gas tank, start the engine and let it  
run until the fuel lines and carburetor are  
empty. Use fresh fuel next season.  
Never use engine or carburetor cleaner prod-  
ucts in the fuel tank or permanent damage  
may occur.  
WARNING: Remove fuel cap slowly  
when refueling.  
This engine is certified to operate on  
unleaded gasoline. Before operation, gasoline  
must be mixed with a good quality synthetic  
2-cycle air-cooled engine oil designed to be  
mixed at a ratio of 40:1. Poulan/Weed Eater  
brand synthetic oil is recommended. A 40:1  
ratio is obtained by mixing 3.2 ounces of oil  
with 1 gallon of unleaded gasoline.  
See the STORAGE section for additional in-  
formation.  
HOW TO STOP YOUR UNIT  
DO NOT USE automotive oil or boat oil.  
These oils will cause engine damage. When S To stop the engine, push and release the  
mixing fuel, follow instructions printed on  
container. Once oil is added to gasoline,  
shake container momentarily to assure that  
the fuel is thoroughly mixed. Always read and  
engine ON/STOP switch. The switch will  
automatically return to the ON position.  
Wait 5 seconds before attempting to restart  
unit to allow switch to reset.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
S If engine does not stop, move choke lever  
to FULL CHOKE position.  
i
Choke  
position  
decal  
Throttle
7. Pull starter rope sharply until engine runs,  
but no more than 6 pulls. If the engine  
doesn’t start after 6 pulls (at the HALF  
CHOKE position), move the choke lever to  
the FULL CHOKE position and press the  
primer bulb 6 times. Squeeze and hold the  
throttle trigger and pull the starter rope 2  
more times. Move the choke lever to the  
HALF CHOKE position and pull the starter  
rope until the engine runs, but no more than  
6 pulls. If the engine doesn’t start, repeat  
procedure 2 additional times.  
HOW TO START YOUR UNIT  
WARNING: The trimmer head will  
turn while starting the engine. Avoid any con-  
tact with the muffler. A hot muffler can cause  
serious burns.  
STARTING A COLD ENGINE (or a  
warm engine after running out of  
fuel)  
NOTE: If engine still doesn’t start, it is  
probably flooded. Proceed to STARTING A  
FLOODED ENGINE.  
8. Once the engine starts, allow it to run 10  
seconds, then move the choke lever to  
OFF CHOKE by aligning lever with posi-  
tion shown on decal (see illustration be-  
low). Allow the unit to run for 30 more se-  
conds at OFF CHOKE before releasing  
the throttle trigger. NOTE: If engine  
dies with the choke lever in the OFF  
CHOKE position, move the choke lever  
to the HALF CHOKE position and pull the  
rope until engine runs, but no more than 6  
pulls.  
Starting Position  
Starter Handle  
Choke  
Lever  
Primer Bulb  
Choke  
position  
decal  
Muffler  
1. Set unit on a flat surface.  
2. Slowly press the primer bulb 6 times.  
3. Move choke lever to FULL CHOKE by  
aligning lever with position shown on de-  
cal (see illustration below).  
STARTING A WARM ENGINE  
1. Move the choke lever to the HALF  
CHOKE position.  
2. Squeeze and hold the throttle trigger.  
Keep throttle trigger fully squeezed until  
the engine runs smoothly.  
Choke  
position  
decal  
3. Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
4. Allow engine to run 15 seconds, then  
move the choke lever to the OFF CHOKE  
position.  
NOTE: If engine has not started, pull start-  
er rope 5 more pulls. If engine still does not  
run, it is probably flooded.  
4. Squeeze the throttle trigger fully and hold  
through all remaining steps.  
5. Pull starter rope handle sharply until en-  
gine sounds as if it is trying to start, but do  
not pull rope more than 6 times.  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing  
the choke lever in the OFF CHOKE position;  
then, pull the rope to clear the engine of ex-  
cess fuel. This could require pulling the starter  
handle many times depending on how badly  
the unit is flooded.  
6. As soon as engine sounds as if it is trying  
to start, move choke lever to HALF  
CHOKE by aligning lever with position  
shown on decal (see following illustra-  
tion).  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the unit still doesn’t start, refer to S The tip of the line does the cutting. You will  
TROUBLESHOOTING TABLE or call  
1-800-554--6723.  
OPERATING POSITION  
achieve the best performance and  
minimum line wear by not crowding the line  
into the cutting area. The right and wrong  
ways are shown below.  
Tip of the Line  
Does The Cutting  
Line Crowded Into  
Work Area  
Right  
Wrong  
S The line will easily remove grass and  
weeds from around walls, fences, trees and  
flower beds, but it also can cut the tender  
bark of trees or shrubs and scar fences.  
S For trimming or scalping, use less than full  
throttle to increase line life and decrease  
head wear, especially:  
Cut from your left to your right.  
S During light duty cutting.  
S Near objects around which the line can  
wrap such as small posts, trees or fence  
wire.  
S For mowing or sweeping, use full throttle for  
a good clean job.  
TRIMMING -- Hold the bottom of the trimmer  
head about 3 in. (8 cm) above the ground and  
at an angle. Allow only the tip of the line to  
make contact. Do not force trimmer line into  
work area.  
WARNING: Always wear eye protec-  
tion. Never lean over the trimmer head. Rocks  
or debris can ricochet or be thrown into eyes  
and face and cause blindness or other serious  
injury.  
Do not run the engine at a higher speed than  
necessary. The cutting line will cut efficiently  
when the engine is run at less than full throttle.  
At lower speeds, there is less engine noise and  
vibration. The cutting line will last longer and will  
be less likely to “weld” onto the spool.  
Trimming  
Always release the throttle trigger and allow  
the engine to return to idle speed when not  
cutting.  
To stop engine:  
3 in. (8 cm)  
Above Ground  
S Release the throttle trigger.  
S Push and release the engine ON/STOP  
switch.  
TRIMMER LINE ADVANCE  
SCALPING -- The scalping technique re-  
moves unwanted vegetation. Hold the bottom  
of the trimmer head about 3 in. (8 cm) above  
the ground and at an angle. Allow the tip of the  
line to strike the ground around trees, posts,  
monuments, etc. This technique increases  
line wear.  
The cutting head advances line automati-  
cally. Do not tap head on the ground to ad-  
vance line. This may break parts and cause  
cutting head to malfunction.  
Upon unit start up, the line will advance auto-  
matically to the correct cutting path length.  
Always keep the shield in place when the tool  
is being operated.  
Scalping  
WARNING: Use only 0.080! (2 mm)  
diameter line. Other sizes of line will not ad-  
vance properly and can cause serious injury.  
Do not use other materials such as wire,  
string, rope, etc. Wire can break off during  
cutting and become a dangerous missile that  
can cause serious injury.  
CUTTING METHODS  
WARNING: Use minimum speed  
MOWING -- Your trimmer is ideal for mowing  
and do not crowd the line when cutting around in places conventional lawn mowers cannot  
hard objects (rock, gravel, fence posts, etc.),  
reach. In the mowing position, keep the line  
which can damage the trimmer head, become parallel to the ground. Avoid pressing the  
entangled in the line, or be thrown causing a head into the ground as this can scalp the  
serious hazard.  
ground and damage the tool.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
SWEEPING -- The fanning action of the rotat-  
ing line can be used for a quick and easy  
clean up. Keep the line parallel to and above  
the surfaces being swept and move the tool  
from side to side.  
Mowing  
Sweeping  
MAINTENANCE  
CLEAN AIR FILTER  
WARNING: Disconnect the spark  
plug before performing maintenance except  
for carburetor adjustments.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Assist Handle Screw  
S Debris Shield  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after every  
5 hours of operation.  
1. Clean the cover and the area around it to  
keep dirt from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts by pressing button to re-  
lease air filter cover.  
NOTE: To avoid creating a fire hazard or  
producing harmful evaporative emissions, do  
not clean filter in gasoline or other flammable  
solvent.  
CHECK FOR DAMAGED OR  
WORN PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S ON/STOP Switch -- Ensure ON/STOP  
switch functions properly by pushing and  
releasing the switch. Make sure engine  
stops. Wait 5 seconds before attempting to  
restart unit to allow switch to reset. Restart  
engine and continue.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Add a few drops of oil to the filter;  
squeeze the filter to distribute oil.  
6. Replace parts.  
Air Filter  
Button  
S Fuel Tank -- Discontinue use of unit if fuel  
tank shows signs of damage or leaks.  
S Debris Shield -- Discontinue use of unit if  
debris shield is damaged.  
Air Filter  
Cover  
INSPECT AND CLEAN UNIT AND DE-  
CALS  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
decals using a damp cloth with a mild deter-  
gent.  
REPLACE SPARK PLUG  
Replace the spark plug each year to ensure  
the engine starts easier and runs better. Set  
spark plug gap at 0.025 in. Ignition timing is  
fixed and nonadjustable.  
S Wipe off unit with a clean dry cloth.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and  
discard.  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
socket wrench.  
4. Reinstall the spark plug boot.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
2. Insert one end of line into center cavity of  
REPLACING THE LINE  
empty spool. Ensure line will feed into  
spool in the direction shown on the spool  
(counterclockwise).  
Pre--wound spools offer the most convenient  
method for replacing line and ensuring opti-  
mum performance.  
3. Continue feeding line into spool, leaving 4  
-- 6 inches (10 -- 15 cm) unwound from  
center of spool.  
S Replacement spools are color--coded to  
ensure use of the correct spool with your  
unit. Be sure to use the same color spool as  
the existing spool.  
INSTALLING SPOOL WITH LINE  
NOTE: Always clear dirt and debris from  
cutting head components when performing  
any type of maintenance.  
1. Install replacement spool.  
2. Thread line through line guide ring.  
Line through guide ring  
S Hold spool and unscrew cap by turning in  
the direction shown on top of the cap.  
S Remove line guide ring and spool.  
Slot  
Line guide ring  
Cap  
Replacement Spool  
3. Rest guide ring on spool and place line in  
slot. Allow line to extend 4 -- 6 inches (10  
-- 15 cm) from center of spool.  
4. Ensure line remains in slot while screw-  
ing cap on to the shaft. Only tighten cap  
hand tight!  
Spool  
Use a pre--wound spool or refill spool with  
line. If using a pre--wound spool, remove tape  
strip from line and spool.  
REFILLING THE SPOOL WITH LINE  
WARNING: Use only 0.080” (2 mm)  
diameter round line. Other sizes and  
shapes of line will not advance properly and  
will result in improper cutting head function or  
can cause serious injury. Do not use other  
materials such as wire, string, rope, etc. Wire  
can break off during cutting and become a  
dangerous missile that can cause serious in-  
jury.  
CARBURETOR ADJUSTMENT  
Your carburetor is equipped with limiter caps.  
Carburetor adjustment is a complicated task.  
We recommend that you take your unit to an  
authorized service dealer. Damage will occur  
if you turn the needles beyond the limiter  
stops.  
1. Cut a length of 30 feet of .080” (2 mm) di-  
ameter round Poulan PRO" brand line.  
Feed line in  
direction  
shown on  
spool.  
Spool  
STORAGE  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
S Store unit and fuel well out of the reach of  
children.  
WARNING: Perform the following  
steps after each use:  
S Allow engine to cool before storing or trans-  
porting.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SEASONAL STORAGE  
ENGINE  
Prepare unit for storage at end of season or if S Remove spark plug and pour 1 teaspoon of  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit before lengthy  
storage.  
S Store in a clean dry area.  
S Lightly oil external metal surfaces.  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
FUEL SYSTEM  
Under FUELING ENGINE in the OPERA-  
TION section of this manual, see message la-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
S At the beginning of the next season, use  
only fresh fuel having the proper gasoline to  
oil ratio.  
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to the gasoline  
in the fuel tank or fuel storage container. Fol-  
low the mix instructions found on stabilizer  
container. Run engine at least 5 minutes after  
adding stabilizer.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts to rust.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing all of the  
recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
Engine will not  
start.  
1. Engine flooded.  
1. See “Starting a Flooded Engine” in  
Operation Section.  
2. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
2. Fill tank with correct fuel mixture.  
3. Install new spark plug.  
4. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
5. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
5. Carburetor requires  
adjustment.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment.  
2. Crankshaft seals worn.  
3. Compression low.  
1. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
2. Contact an authorized service dealer.  
3. Contact an authorized service dealer.  
1. Air filter dirty.  
1. Clean or replace air filter.  
2. Clean or replace plug  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
2. Spark plug fouled.  
and regap.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
5. Compression low.  
3. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
4. Contact an authorized service dealer.  
5. Contact an authorized service dealer.  
Engine  
1. Choke partially on.  
1. Adjust choke.  
smokes  
2. Fuel mixture incorrect.  
2. Empty fuel tank and refill with  
correct fuel mixture.  
excessively.  
3. Air filter dirty.  
4. Carburetor requires  
adjustment.  
3. Clean or replace air filter.  
4. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
1. See “Fueling Engine” in Operation  
section.  
2. Replace with correct spark plug.  
3. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
4. Contact an authorized service dealer.  
Engine runs  
hot.  
1. Fuel mixture incorrect.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
er predelivery setup or normal adjustments  
warrants to the original purchaser that each explained in the instruction manual.  
new Poulan PRO" brand gasoline tool or at- THIS WARRANTY GIVES YOU SPECIFIC  
tachment is free from defects in material and LEGAL RIGHTS, AND YOU MAY HAVE  
workmanship and agrees to repair or replace  
under this warranty any defective gasoline  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
product or attachment as follows from the NO CLAIMS FOR CONSEQUENTIAL OR  
original date of purchase.  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
2 YEARS-- Parts and Labor, when used for  
household purposes.  
90 DAYS -- Parts and Labor, when used for  
commercial, professional, or income produc- SOME STATES DO NOT ALLOW LIMITA-  
ing purposes.  
TIONS ON HOW LONG AN IMPLIED WAR-  
30 DAYS -- Parts and Labor, if used for rental RANTY LASTS OR THE EXCLUSION OR  
purposes.  
LIMITATIONS OF INCIDENTAL OR CON-  
This warranty is not transferable and does not SEQUENTIAL DAMAGES, SO THE ABOVE  
cover damage or liability caused by improper LIMITATIONS OR EXCLUSION MAY NOT  
handling, improper maintenance, or the use APPLY TO YOU.  
of accessories and/or attachments not spe- The policy of ELECTROLUX HOME PROD-  
cifically recommended by ELECTROLUX  
UCTS, INC., is to continuously improve its  
products. Therefore, ELECTROLUX HOME  
HOME PRODUCTS, INC., for this tool. Addi-  
tionally, this warranty does not cover tune- PRODUCTS, INC., reserves the right to  
ups, spark plugs, filters, cutting line, or rotat- change, modify, or discontinue models, de-  
ing head parts that will wear and require  
signs, specifications, and accessories of all  
replacement with reasonable use during the products at any time without notice or obliga-  
warranty period. This warranty does not cov- tion to any purchaser.  
U.S. EPA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OBLIGA-  
maintenance. As the small off--road engine  
TIONS: The U. S. Environmental Protection owner, you should be aware that POULAN/  
Agency and POULAN/WEED EATER, DIVI-  
SION OF WCI OUTDOOR PRODUCTS, INC.,  
WEED EATER may deny you warranty cover-  
age if your small off--road engine or a part of it  
are pleased to explain the emissions control has failed due to abuse, neglect, improper main-  
system warranty on your year 2001--2004 small tenance, unapproved modifications, or the use  
off--road engine. POULAN/WEED EATER of parts not made or approved by the original  
must warrant the emission control system on equipment manufacturer. You are responsible  
your small off--road engine for the periods of for presenting your small off--road engine to a  
time listed below provided there has been no POULAN/WEED EATER authorized repair  
abuse, neglect, or improper maintenance of center as soon as a problem exists. Warranty  
your small off--road engine. Your emission con- repairs should be completed in a reasonable  
trol system includes parts such as the carbure-  
amount of time, not to exceed 30 days. If you  
tor and the ignition system. Where a warrant- have any questions regarding your warranty  
able condition exists, POULAN/WEED EATER rights and responsibilities, you should contact  
will repair your small off--road engine at no cost your nearest authorized service center or call  
to you. Expenses covered under warranty in-  
clude diagnosis, parts and labor. MANUFAC- WARRANTY COMMENCEMENT DATE: The  
TURER’S WARRANTY COVERAGE: If any  
warranty period begins on the date the small  
POULAN/WEED EATER at 1--800--554--6723.  
emissions related part on your engine (as listed off--road engine is purchased. LENGTH OF  
under Emissions Control Warranty Parts List) is COVERAGE: This warranty shall be for a peri-  
defective or a defect in the materials or work- od of two years from the initial date of purchase.  
manship of the engine causes the failure of such WHAT IS COVERED: REPAIR OR RE-  
an emission related part, the part will be repaired PLACEMENT OF PARTS. Repair or replace-  
or replaced by POULAN/WEED EATER.  
ment of any warranted part will be performed at  
no charge to the owner at an approved POU-  
OWNER’S WARRANTY RESPONSIBILI-  
TIES: As the small off--road engine owner, you LAN/WEED EATER servicing center. If you  
are responsible for the performance of the re- have any questions regarding your warranty  
quired maintenance listed in your instruction rights and responsibilities, you should contact  
manual. POULAN/WEED EATER recom-  
your nearest authorized service center or call  
mends that you retain all receipts covering POULAN/WEED EATER at 1--800--554--6723.  
maintenance on your small off--road engine, but WARRANTY PERIOD: Any warranted part  
POULAN/WEED EATER cannot deny warran-  
which is not scheduled for replacement as re-  
ty solely for the lack of receipts or for your failure quired maintenance, or which is scheduled only  
to ensure the performance of all scheduled for regular inspection to the effect of ”repair or  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
replace as necessary” shall be warranted for 2  
years. Any warranted part which is scheduled  
CLAIM: If you have any questions regarding  
your warranty rights and responsibilities, you  
for replacement as required maintenance shall should contact your nearest authorized service  
be warranted for the period of time up to the first center or call POULAN/WEED EATER at  
scheduled replacement point for that part. 1--800--554--6723. WHERE TO GET WAR-  
DIAGNOSIS: The owner shall not be charged  
RANTY SERVICE: Warranty services or re-  
for diagnostic labor which leads to the deter- pairs shall be provided at all POULAN/WEED  
mination that a warranted part is defective if the EATER service centers. Call 1--800--554--6723.  
diagnostic work is performed at an approved MAINTENANCE, REPLACEMENT AND RE-  
POULAN/WEED EATER servicing center.  
CONSEQUENTIAL DAMAGES: POULAN/  
PAIR OF EMISSION RELATED PARTS: Any  
POULAN/WEED EATER approved replace-  
WEED EATER may be liable for damages to ment part used in the performance of any war-  
other engine components caused by the failure ranty maintenance or repair on emission related  
of a warranted part still under warranty. WHAT parts will be provided without charge to the own-  
IS NOT COVERED: All failures caused by  
er if the part is under warranty. EMISSION  
abuse, neglect, or improper maintenance are CONTROL WARRANTY PARTS LIST: Car-  
not covered. ADD--ON OR MODIFIED buretor, Ignition System: Spark Plug (covered  
PARTS: The use of add--on or modified parts up to maintenance schedule), Ignition Module.  
can be grounds for disallowing a warranty claim. MAINTENANCE STATEMENT: The owner is  
POULAN/WEED EATER is not liable to cover responsible for the performance of all required  
failures of warranted parts caused by the use of maintenance as defined in the instruction  
add--on or modified parts. HOW TO FILE A manual.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Perlick Beverage Dispenser Keg Couplers Tapping Equipment User Manual
Philips Hair Dryer HP4997 15 User Manual
Philips Speaker SPA2300 User Manual
Philips Stereo Receiver FR755 User Manual
Philips TV DVD Combo 29PD6932 User Manual
Philips Work Light P 5759 D User Manual
Polk Audio Speaker PSWi225 User Manual
Powermate Portable Generator PM050562217 User Manual
ProForm Home Gym PFEL87075 User Manual
PVI Industries Water Heater 750P600A TPGO User Manual