Poulan Lawn Mower XT22H42YT User Manual

IMPORTANT MANUAL  
Do Not Throw Away  
03076  
OPERATOR'S MANUAL  
WARNING:  
Read this Manual and follow allWarnings and  
SafetyInstructions. Failuretodosocanresult  
in serious injury.  
MODEL:  
XT22H42YT  
LAWN TRACTOR  
ALWAYS WEAR EYE PROTECTION DURING OPERATION  
404378 Rev.2 03.16.06 VB  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any fuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
IV.TOWING  
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
To avoid personal injury or property damage, use extreme  
care in handling gasoline.Gasoline is extremely flammable  
and the vapors are explosive.  
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine run-  
ning. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Removegas-poweredequipmentfromthetruckortrailer  
and refuel it on the ground. If this is not possible, then  
refuel such equipment with a portable container, rather  
than from a gasoline dispenser nozzle.  
Keep the nozzle in contact with the rim of the fuel tank  
orcontaineropeningatalltimesuntilfuelingiscomplete.  
Do not use a nozzle lock-open device.  
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT SPECIFICATIONS  
CUSTOMER RESPONSIBILITIES  
Gasoline Capacity  
and type:  
3 Gallons  
Read and observe the safety rules.  
Unleaded Regular  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Follow the instructions underMaintenanceandStor-  
age” sections of this owner’s manual.  
Oil Capacity:  
W/ Filter:  
W/O Filter:  
4.0 Pints  
3.75 Pints  
Spark Plug:  
(Gap: .040")  
Champion QC12YC  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Ground Speed (MPH):  
Charging System:  
Battery:  
Forward:  
Reverse:  
0 – 5.5  
0 – 2.4  
3 AMPS Battery  
5 AMPS Headlights  
AMP/HR:  
MIN. CCA:  
Case Size:  
35  
280  
U1R  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply on  
federal lands.  
Blade Bolt Torque:  
45-55FT. LBS.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
TABLE OF CONTENTS  
SAFETY RULES ............................................................ 2  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................... 5  
OPERATION .................................................................. 7  
MAINTENANCE SCHEDULE ...................................... 14  
MAINTENANCE.......................................................... 14  
SERVICE AND ADJUSTMENTS ................................. 18  
STORAGE.................................................................... 24  
TROUBLESHOOTING ................................................. 25  
WARRANTY................................................................. 27  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Slope Sheet  
Key  
(1) Oil Drain Tube  
(2) Keys  
ASSEMBLY  
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping  
puposes.  
Whenrightorlefthandismentionedinthismanual,itmeans  
ADJUST SEAT (See Fig. 2)  
when you are in the operating position (seated behind the  
Sit in seat.  
steering wheel).  
Lift up adjustment lever (A) and slide seat until a com-  
fortable position is reached which allows you to press  
clutch/brake pedal all the way down.  
TO REMOVE TRACTOR FROM  
CARTON  
Release lever to lock seat in position.  
UNPACK CARTON  
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dashed lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
A
CHECK BATTERY (See Fig. 1)  
Lift hood to raised position.  
NOTE:Ifthisbatteryisputintoserviceaftermonthandyear  
indicated on label (L) (label is located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in Maintenance section of this manual  
for charging instructions).  
FIG. 2  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
L
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
02931  
Raise attachment lift lever to its highest position.  
FIG. 1  
Release parking brake by depressing clutch/brake  
pedal.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Place freewheel control in "transmission disengaged  
position" (See “TO TRANSPORT” in the Operation  
section of this manual).  
Roll tractor forward off skid.  
Removebandingholdingthedeflectorshieldupagainst  
tractor.  
CHECKLIST  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISHTO ASSURETHATYOU RECEIVETHE BEST PER-  
FORMANCE AND SATISFACTION FROMTHIS QUALITY  
PRODUCT.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
All assembly instructions have been completed.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
No remaining loose parts in carton.  
Battery is properly prepared and charged.  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
Be sure all the above assembly steps have been com-  
pleted.  
Check engine oil level and fill fuel tank with gasoline.  
Place freewheel control in "transmission engaged"  
position (see "TO TRANSPORT" in Operation section  
of this manual).  
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
Place motion control lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
Remove key from bag and start the engine (see "TO  
START ENGINE" in the Operation section of this man-  
ual). After engine has started, move throttle control to  
idle (slow) position.  
Engine oil is at proper level.  
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse Op-  
eration System (ROS) are working properly (See the  
Operation and Maintenance sections in this manual).  
It is important to purge the transmission before oper-  
ating your tractor for the first time. Follow proper start-  
ing and transmission purging instructions (See “TO  
START ENGINE” and “PURGE TRANSMISSION” in  
the Operation section of this manual).  
Release parking brake.  
Slowlymovethemotioncontrolleverforwardandslowly  
drive tractor off skid.  
Apply brake to stop tractor, setparkingbrakeandplace  
motion control lever in neutral position.  
Turn ignition key to "STOP" position.  
Continue with the instructions that follow.  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
Reduce tire pressure to PSI shown on tires.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. SeeTOLEVELMOWERHOUSINGintheService  
and Adjustments section of this manual.  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
ing.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
G
P
H
D
B
E
N
F
C
A
J
M
FIG. 3  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER – Used to raise and lower the  
mower or other attachments mounted to your tractor.  
(B) CLUTCH/BRAKE PEDAL – Used for braking the tractor  
and starting the engine.  
(C) PARKING BRAKE – Locks clutch/brake pedal into the  
brake position.  
(G) REVERSE OPERATION SYSTEM (ROS) "ON" POSITION  
– Allows operation of mower or other powered attachment  
while in reverse.  
(H) LIGHT SWITCH Turns the headlights on and off.  
(J) MOTION CONTROL LEVER – Selects the speed and  
direction of tractor.  
(D) THROTTLE CONTROL – Used to control engine speed.  
(E) ATTACHMENT CLUTCH LEVER – Used to engage the  
mower blades, or other attachments mounted to your tractor.  
(F) IGNITION SWITCH – Used for starting and stopping the  
engine.  
(M) FREEWHEEL CONTROL – Disengages transmission for  
pushing or slowly towing the tractor with the engine off.  
(N) CHOKE CONTROL - Used when starting a cold engine.  
(P) SERVICE REMINDER / HOUR METER – Indicates when  
service is required for the engine and mower.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor  
or performing any adjustments or repairs. We recommend standard safety glasses or a wide  
vision safety mask worn over spectacles.  
Turn ignition key (F) to “STOP” position and remove  
key. Alwaysremovekeywhenleavingtractortoprevent  
unauthorized use.  
HOW TO USEYOUR TRACTOR  
TO SET PARKING BRAKE(See Fig. 4)  
Never use choke to stop engine.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
IMPORTANT: Leaving the ignition switch in any position  
other than "STOP" will cause the battery to discharge and  
go dead.  
Depress clutch/brake pedal (B) all the way down and  
hold.  
Pull parking brake lever (C) up and hold, release pres-  
sure from clutch/brake pedal (B), then release parking  
brake lever. Pedal should remain in brake position.  
Make sure parking brake will hold tractor secure.  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
CAUTION: Always stop tractor com-  
pletely, as described above, before  
leaving the operator's position.  
B
C
D
FIG. 4  
F
STOPPING  
MOWER BLADES -  
N
To stop mower blades, move attachment clutch lever to  
disengaged position (  
).  
FIG. 6  
TO USETHROTTLE CONTROL - D (See Fig. 6)  
Always operate engine at full speed (fast).  
Operating engine at less than full speed (fast) reduces  
engines operating efficiency.  
Full speed (fast) offers the best bagging and mower  
performance.  
J
TO USE CHOKE CONTROL - N (See Fig. 6)  
Use choke control whenever you are starting a cold engine.  
Do not use to start a warm engine.  
FIG. 5  
(
) Attachment  
(
) Disengaged  
Clutch  
Position  
Engage Position  
To engage choke control, pull knob out. Slowly push  
knob in to disengage.  
GROUND DRIVE -  
To stop ground drive, depress clutch/brake pedal all  
the way down.  
Move motion control lever (J) to neutral position.  
ENGINE -  
Move throttle control (D) between half and full speed  
(fast) position.  
NOTE: Failure to move throttle control between half and  
full speed (fast) position, before stopping, may cause en-  
gine to “backfire”.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO MOVE FORWARD AND BACKWARD  
TO ADJUST GAUGE WHEELS (See Fig. 9)  
(See Fig. 7)  
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
The direction and speed of movement is controlled by the  
motion control lever. (J)  
Start tractor with motion control lever in neutral (N)  
position.  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
Release parking brake.  
Slowly move motion control lever to desired position.  
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in this section of  
manual).  
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
J
FIG. 7  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 8)  
The position of the attachment lift lever (A) determines the  
cutting height.  
FIG.9  
TO OPERATE MOWER  
T
Your tractor is equipped with an operator presence sensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged  
will shut off the engine.You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitating  
or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
A
Select desired height of cut with attachment lift lever.  
Start mower blades by engaging attachment clutch  
control.  
FIG. 8  
Put attachment lift lever in desired cutting height slot.  
Slide pointer tab (T) to desired cutting height as a  
reminder for next time you mow.  
TO STOP MOWER BLADES -  
disengage attachment clutch control.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
theenginenotrunning. Theseheightsareapproximateand  
may vary depending upon soil conditions, height of grass  
and types of grass being mowed.  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield (S) in place.  
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
S
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
FIG. 10  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO TRANSPORT (See Figs. 3 and 11)  
REVERSE OPERATION SYSTEM (ROS)  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
direction with the attachment clutch engaged will shut off  
the engine unless ignition key is placed in the ROS "ON"  
position.  
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
Transmission Engaged  
Move motion control lever to neutral (N) position.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
Look down and behind before and while backing.  
Slowlymovemotioncontrollevertoreverse(R)position  
to start movement.  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
ROS "ON" POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Transmission Disengaged  
FIG. 11  
SERVICE REMINDER/HOUR METER  
Service reminder shows the total number of hours the  
engine has run and flashes to indicate that the engine  
or mower needs servicing. When service is required, the  
service reminder will flash for two hours.To service engine  
and mower, see the Maintenance section of this manual.  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure  
key remains in the "STOP" position when engine is not  
running.  
TO OPERATE ON HILLS  
TOWING CARTS AND OTHER ATTACHMENTS  
CAUTION: Donotdriveupordownhills  
with slopes greater than 15° and do not  
drive across any slope.  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
Choose the slowest speed before starting up or down  
hills.  
Avoid stopping or changing speed on hills.  
BEFORE STARTING THE ENGINE  
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
Move motion control lever to neutral (N) position.  
factory, already filled with summer weight oil.  
IMPORTANT:  
THE MOTIONCONTROLLEVERDOESNOT  
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/  
BRAKE PEDAL IS DEPRESSED.  
Check engine oil with tractor on level ground.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
Slowly move motion control lever to slowest setting.  
Make all turns slowly.  
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The attachments and ground drive can now be used. If  
ADD GASOLINE  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
Fill fuel tank to bottom of filler neck. Do not overfill. Use  
fresh,clean,regularunleadedgasolinewithaminimumof  
87 octane. (Use of leaded gasoline will increase carbon  
and lead oxide deposits and reduce valve life). Do not  
mix oil with gasoline. Purchase fuel in quantities that can  
be used within 30 days to assure fuel freshness.  
COLD WEATHER STARTING (50° F and below)  
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. Continue to push  
the choke control in small steps allowing the engine to  
acceptsmallchangesinspeedandload,untilthechoke  
control is fully in.If the engine starts to run roughly, pull  
thechokecontroloutslightlyforafewsecondsandthen  
continue to push the control in slowly.This may require  
an engine warm-up period from several seconds to  
several minutes, depending on the temperature.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store,spill or use gasoline  
near an open flame.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
AUTOMATIC TRANSMISSION WARM UP  
Beforedrivingtheunitincoldweather, thetransmission  
should be warmed up as follows:  
CAUTION: Alcohol blended fuels (called gasohol or  
usingethanolormethanol)canattractmoisturewhich  
leads to separation and formation of acids during  
storage. Acidic gas can damage the fuel system of  
anenginewhileinstorage.Toavoidengineproblems,  
the fuel system should be emptied before storage  
of 30 days or longer. Drain the gas tank, start the  
engineandletitrununtilthefuellinesandcarburetor  
are empty. Use fresh fuel next season. See Storage  
Instructions for additional information. Never use  
engine or carburetor cleaner products in the fuel  
tank or permanent damage may occur.  
Be sure the tractor is on level ground.  
Place the motion control lever in neutral.  
Release the parking brake and let the clutch/brake  
slowly return to operating position.  
Allow one minute for transmission to warm up.This  
can be done during the engine warm up period.  
Theattachmentscanbeusedduringtheenginewarm-up  
period after the transmission has been warmed up and  
may require the choke control be pulled out slightly.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
TO START ENGINE (See Fig. 6)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
PURGE TRANSMISSION  
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
CAUTION: Never engage or disengage  
freewheel lever while the engine is run-  
ning.  
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
Place motion control lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to fast position  
Pull choke control out for a cold engine start attempt.  
For a warm engine start attempt the choke control may  
not be needed.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BE PURGED AFTER REINSTALLATION BEFORE OPERATING  
THE TRACTOR.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
Insert key into ignition and turn key clockwise to  
“START” position and release key as soon as engine  
starts. Do not run starter continuously for more than  
fifteen seconds per minute.If the engine does not start  
after several attempts, push choke control in, wait a  
few minutes and try again.If engine still does not start,  
pull the choke control out and retry.  
Place tractor safely on a level surface - that is clear and  
open - with engine off and parking brake set.  
Disengage transmission by placing freewheel control  
infreewheelingposition(SeeTOTRANSPORTinthis  
section of manual).  
Sitting in the tractor seat, start engine.After the engine  
is running, move throttle control to slow position. With  
motion control lever in neutral (N) position, slowly dis-  
engage clutch/brake pedal.  
WARM WEATHER STARTING (50° F and above)  
When engine starts, slowly push choke control in until  
the engine begins to run smoothly. If the engine starts  
to run roughly, pull the choke control out slightly for a  
few seconds and then continue to push the control in  
slowly.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
CAUTION: At any time, during step 4,  
there may be movement of the drive  
wheels.  
Move motion control lever to full forward position and  
hold for five (5) seconds. Move lever to full reverse  
position and hold for five (5) seconds. Repeat this  
procedure three (3) times.  
Move motion control lever to neutral (N) position.Shut-  
off engine and set parking brake.  
Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
Sitting in the tractor seat, start engine.After the engine  
is running, move throttle control to half (1/2) speed.  
With motion control lever in neutral (N) position, slowly  
disengage clutch/brake pedal.  
Slowly move motion control lever forward, after the  
tractor moves approximately five (5) feet, slowly move  
motion control lever to reverse position. After the trac-  
tor moves approximately five (5) feet return the mo-  
tion control lever to the neutral (N) position. Repeat  
this procedure with the motion control lever three (3)  
times.  
FIG. 12  
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
Your transmission is now purged and now ready for normal  
operation.  
MOWING TIPS  
Mower should be properly leveled for best mowing per-  
formance. SeeTO LEVEL MOWER HOUSINGin the  
Service and Adjustments section of this manual.  
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 12).  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
T Check Tire Pressure  
R Check Operator Presence & ROS Systems  
A Check for Loose Fasteners  
Check/Replace Mower Blades  
3
4
C
T
0
Lubrication Chart  
Check Battery Level  
Clean Battery and Terminals  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
R
Check Engine Oil Level  
1,2  
Change Engine Oil (with oil filter)  
1,2  
E Change Engine Oil (without oil filter)  
N Clean Air Filter  
2
2
G Clean Air Screen  
Inspect Muffler/Spark Arrester  
I
N
1,  
2
2
Replace Oil Filter (If equipped)  
E Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
SPINDLE ZERK  
SPINDLE ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
FRONT  
WHEEL  
FRONT  
WHEEL  
BEARING  
ZERK  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
ENGINE  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
• At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
STEERING  
SECTOR GEAR  
TETH  
02956  
BEFORE EACH USE  
General Purpose Grease  
Check engine oil level.  
Refer to Maintenance “ENGINE” Section  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
ROS systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOU FEELTHEY MUST BE LUBRICATED, USE ONLY A DRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BLADE CARE  
For best results mower blades must be sharp. Replace  
worn, bent or damaged blades.  
TRACTOR  
Always observe safety rules when performing any main-  
tenance.  
CAUTION: Useonlyareplacementblade  
approved by the manufacturer of your  
tractor. Using a blade not approved  
by the manufacturer of your tractor is  
hazardous, could damage your tractor  
and void your warranty.  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced. (See “TO CHECK  
BRAKE” in the Service and Adjustments section of this  
manual).  
BLADE REMOVAL (See Fig. 13)  
TIRES  
Raise mower to highest position to allow access to  
blades.  
Maintain proper air pressure in all tires (See PSI on  
tires).  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
Remove blade bolt by turning counterclockwise.  
Install new blade with stamped "GRASS SIDE" facing  
the ground.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
IMPORTANT: To ensure proper assembly, center hole in  
blade must align with star on mandrel assembly.  
Install and tighten blade bolt securely (45-55 Ft. Lbs.  
torque).  
OPERATOR PRESENCE SYSTEM AND REVERSE OP-  
ERATION SYSTEM (ROS)  
IMPORTANT: Special blade bolt is heat treated.  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
MANDREL  
ASSEMBLY  
BLADE  
CENTER  
HOLE  
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
BLADE BOLT  
(SPECIAL)  
CHECK OPERATOR PRESENCE SYSTEM  
025  
44  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
STAR  
FIG. 13  
The attachment clutch should never operate unless  
the operator is in the seat.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Engine "ON" Position  
ROS "ON" Position  
(Normal Operating)  
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
When the engine is running with the ignition switch in  
the ROS "ON" position and the attachment clutch en-  
gaged, any attempt by the operator to shift into reverse  
should NOT shut off the engine.  
Remove terminal guard.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TO CHANGE ENGINE OIL (See Fig. 15)  
Rinse the battery with plain water and dry.  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
Coat terminals with grease or petroleum jelly.  
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
V-BELTS  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
OIL DRAIN VALVE  
TRANSAXLE COOLING  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot.To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
CLOSED  
AND  
LOCKED  
POSITION  
Inspect cooling fan to be sure fan blades are intact and  
clean.  
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean cool-  
ing fins.  
DRAIN  
TUBE  
YELLOW CAP  
TRANSAXLE PUMP FLUID  
FIG. 15  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
ENGINE  
LUBRICATION  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
SAE VISCOSITY GRADES  
SAE 30  
5W-30  
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil atFULLline on dipstick.Tighten cap  
onto the tube securely when finished.  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
FIG. 14  
CLEAN AIR SCREEN  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove3F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.See  
Engine Manual.  
Change the oil after every 50 hours of operation or at least  
once a year if the tractor is not used for 50 hours in one  
year.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
ENGINE OIL FILTER  
Replace the engine oil filter every season or every other  
oil change if the tractor is used more than 100 hours in  
one year.  
CLAMP  
CLAMP  
FUEL FILTER  
MUFFLER  
FIG. 16  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
CLEANING  
Clean engine, battery, seat, finish, etc. of all foreign  
SPARK PLUGS  
matter.  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
IN-LINE FUEL FILTER (See Fig. 16)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING:TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:  
Depress clutch/brake pedal fully and set parking brake.  
Place motion control lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
TRACTOR  
Go to either side of mower and disconnect mower  
suspension arm (A) from chassis pin (B) and rear lift  
link (C) from rear mower bracket (D) - remove retainer  
springs and washers.  
TO REMOVE MOWER (See Fig. 17)  
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift lever to its lowest position.  
Roll belt off engine pulley (M).  
Removeretainerspring(K),slidecollar(L)offandpush  
housing guide (P) out of bracket.  
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
CAUTION: After rear lift links are dis-  
connected,theattachmentliftleverwill  
be spring loaded. Have a tight grip on  
lift lever when changing position of  
the lever.  
Remove clutch cable spring (Q) from idler arm (R).  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
M
B
F
Q
R
E
A
H
P
C
D
L
K
FIG. 17  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
Slide mower out from under right side of tractor.  
IMPORTANT: If an attachment other than the mower deck  
is to be mounted on the tractor, remove the front link (E)  
and rear lift liks (C) from tractor.  
E
TO INSTALL MOWER (See Figs. 18-21)  
Be sure tractor is on level surface and engage parking  
brake.  
J
F
Lower attachment lift lever to it's lowest position.  
H
CAUTION: Lift lever is spring loaded.  
Have a tight grip on lift lever, lower it  
slowly and engage in lowest position.  
FIG. 20  
Push clutch cable housing guide (P) into bracket, slide  
collar (L) onto guide and secure with retainer spring  
(K).  
Hook end of clutch cable spring (Q) into hole in idler  
arm (R).  
NOTE: Be sure mower side suspension arms (A) are point-  
ing forward before sliding mower under tractor.  
Slide mower under tractor until it is centered under  
tractor.  
ATTACH MOWER SIDE SUSPENSION ARMS (A) TO  
CHASSIS - Position hole in arm over pin (B) on outside  
of tractor chassis and secure with washer and retainer  
spring.  
Install belt onto engine pulley (M).  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
Repeat on opposite side of tractor.  
M
A
B
FIG. 18  
FIG. 21  
ATTACH REAR LIFT LINKS (C) - Lift rear corner of  
mower and position slot in link assembly over pin on  
rear mower bracket (D) and secure with washer and  
retainer spring.  
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mower as shown in the Operation section of this  
manual.  
Repeat on opposite side of tractor.  
C
D
FIG. 19  
ATTACH FRONT LINK (E) - Work from left side of trac-  
tor. Insert rod end of link assembly through front hole  
in tractor front suspension bracket (F).  
Insert end of link (E) into hole in front mower bracket  
(H) and secure with washer and retainer spring (J).  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO LEVEL MOWER  
02966  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
A
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 22)  
With all tires properly inflated and if your lawn appears  
unevenly cut, determine which side of mower is cutting  
lower.  
FIG. 23  
FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25)  
IMPORTANT: Deck must be level side-to-side.  
NOTE: As desired, you can raise the low side of mower or  
lower the high side.  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
Go to side of mower you wish to adjust.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower the mower, or, to the  
right to raise the mower.  
CAUTION: Blades are sharp.Protect your  
hands with gloves and/or wrap blade with  
heavy cloth.  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
Testyouradjustmentbymowingsomeuncutgrassand  
visually checking the appearance. Readjust, if neces-  
sary, until you are satisfied with the results.  
Raise mower to highest position.  
Positionanybladesothetipispointingstraightforward.  
Measure distance (B) to the ground at front and rear  
tip of the blade.  
A
If front tip of blade is not 1/8" to 1/2" lower than the rear  
tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut  
A several turns to clear adjustment nut B.  
With a 3/4" or adjustable wrench, turn front link adjust-  
ment nut (B) clockwise (tighten) to raise the front of  
mower, or, counterclockwise (loosen) to lower the front  
mower.  
A
02548  
Turn nut left  
to lower mower  
B
Turn nut right  
to raise mower  
B
02948  
FIG. 24  
FIG. 22  
PRECISION SIDE-TO-SIDE ADJUSTMENT  
(See Fig. 23)  
With all tires properly inflated, park tractor on level  
ground or driveway.  
B
A
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
Raise mower to its highest position.  
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
If adjustment is necessary, see steps in Visual Adjust-  
ment instructions above.  
Recheck measurements, adjust if necessary until both  
sides are equal.  
Tighten adjust nut  
Loosen adjust nut  
B to lower mower  
B to raise mower  
02950  
Loosen jam nut A first  
FIG. 25  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
NOTE: Each full turn of the adjustment nut will change  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 27)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
mower height about 1/8".  
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
BELT REMOVAL -  
TO REPLACE MOWER DRIVE BELT  
(See Fig. 26)  
MOWER DRIVE BELT REMOVAL  
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
Park tractor on a level surface. Engage parking  
brake.  
Remove belt from stationary idler (A) and clutching  
idler (B).  
Remove belt from centerspan idler (C).  
Pull belt slack toward rear of tractor. Remove belt  
upwards from transaxle input pulley (D).  
Remove belt downward from engine pulley (E).  
Lower attachment lift lever to its lowest position.  
Remove any dirt or grass clippings which may have  
accumulated around mandrels and entire upper deck  
surface.  
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (S).  
Slide belt toward rear of tractor, off the steering plate  
(F) and remove from tractor.  
MOWER DRIVE BELT INSTALLATION  
BELT INSTALLATION -  
Install belt around all mandrel pulleys (R) and around  
idler pulleys (S) as shown.  
Install new belt from tractor rear to front, over the steer-  
ing plate (F) and above clutch brake pedal shaft (G).  
Install belt onto electric clutch pulley (M).  
Pull belt toward front of tractor and roll belt onto engine  
pulley (E).  
Pullbelttowardrearoftractor.Carefullyworkbeltdown  
around transaxle input pulley (D).Be sure belt is inside  
the belt keeper.  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
Raise attachment lift lever to highest position.  
Install belt on centerspan idler (C).  
Install belt through stationary idler (A) and clutching  
idler (B).  
S
M
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
R
E
R
F
FIG. 26  
A
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
G
B
C
You may also check brake by:  
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
D
Place gear shift lever in neutral (N) position.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate, then  
the brake needs to be serviced.Contact a qualified service  
center.  
21  
FIG. 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 29)  
FRONT WHEEL TOE-IN/CAMBER  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 28)  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
Block up axle securely.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
TO ATTACH JUMPER CABLES -  
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
TO REMOVE CABLES, REVERSE ORDER -  
WASHERS  
BLACK cable first from chassis and then from the fully  
charged battery.  
RETAINING  
RING  
RED cable last from both batteries.  
AXLE COVER  
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 28  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
FIG. 29  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REMOVE HOOD AND GRILL ASSEMBLY  
REPLACING BATTERY (See Fig. 30)  
(See Fig. 31)  
WARNING: Do not short battery terminals by allowing  
a wrench or any other object to contact both terminals at  
the same time. Before connecting battery, remove metal  
bracelets, wristwatch bands, rings, etc.  
Raise hood.  
Unsnap headlight wire connector.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
Positive terminal must be connected first to prevent spark-  
ing from accidental grounding.  
To replace, reverse above procedure.  
Lift hood to raised position.  
Disconnect BLACK battery cable (A) then RED battery  
cable and carefully remove battery from tractor.  
HOOD  
Install new battery with terminals in same position as  
old battery.  
FirstconnectREDbatterycable(B)topositive(+)battery  
terminal with hex bolt and keps nut as shown.Tighten  
securely. Slide terminal cover (C) over terminal.  
HEADLIGHT  
WIRE  
CONNECTOR  
ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining hex bolt and keps nut.Tighten  
securely  
03075  
Close hood.  
Negative  
(Black)  
Cable  
A
FIG. 31  
ENGINE  
C
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
B
Positive  
(Red)  
Cable  
TO ADJUST CHOKE CONTROL  
02954  
The choke control has been preset at the factory and ad-  
justment should not be necessary. If adjustment is neces-  
sary, see engne manual.  
FIG. 30  
TO REPLACE HEADLIGHT BULB  
TO ADJUST CARBURETOR  
Raise hood.  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
CYLINDER(S)  
Fully charge the battery for storage.  
Remove spark plug(s).  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
After a period of time in storage, battery may require  
recharging.  
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
Turn ignition key to “STARTposition for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Weak or dead battery.  
6. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Recharge or replace battery.  
6. Clean/replace air filter.  
7. Dirty fuel filter.  
7. Replace fuel filter.  
8. Water in fuel.  
8. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
9. Loose or damaged wiring.  
9. Check all wiring.  
10. Carburetor out of adjustment.  
10. See To Adjust Carburetor” in Service Adjustments  
section.  
11. Engine valves out of adjustment.  
11. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gasoline.  
6. Check all wiring.  
7. See To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gasoline.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine dies when  
tractor is shifted  
into reverse  
1. Reverse operation system  
(ROS) is not "ON" while  
1. Turn ignition key to  
ROS "ON" position.  
mower or other attachment  
is engaged.  
See Operation section.  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Light switch is “OFF”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
1. Turn light switch “ON”.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
Loss of drive  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-  
als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or  
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due  
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.  
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components, battery (ex-  
cept as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur-  
chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser  
unless such return is requested by Electrolux Home Products.  
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find  
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the  
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must  
be maintained in accordance with the instructions furnished.  
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original  
purchase.  
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accor-  
dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration,  
misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.  
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard  
hardware and normal maintenance.  
7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Electrolux Home Products, Inc.  
Electrolux Canada Corp.  
7075 Ordan Drive  
Mississauga, Ontario  
L5T 1K6  
Outdoor Products Customer Service Dept.  
1030 Stevens Creek Road  
Augusta, GA 30907 USA  
giving the model number, serial number and date of purchase of your product and the name and address of the authorized  
dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-  
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas  
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-  
tations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which  
vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS AND SERVICE  
This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all  
mechanical products, some adjustments or part replacement may be necessary during the life of your unit.  
For Parts and service, contact our authorized distributor: call 1-800-849-1297  
For replacement parts, have available the following information:  
a. Model Number/Manufacturer's I.D. Number  
b. Description of part.  
For Techical Assistance: call 1-800-829-5886  
NOTE: Electrolux Home Products provides parts and service through its authorized distributors and  
dealers; therefore, all requests for parts and service should be directed to your local dealer(s).  
The philosophy of Electrolux Home Products is to continually improve all of its products. If  
the operating characteristics or the appearance of your product differs from those described  
in this Manual, please contact your local dealer for updated information and assistance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Computer Monitor 107Q User Manual
Philips Home Theater System 19MD357B 37 User Manual
Philips MP3 Player UDA1334BT User Manual
Philips Sewing Machine RFX6500 User Manual
Philips TV Cables SWV6622 User Manual
Philips TV Cables SWV7562W User Manual
Pioneer Home Theater System HTZ 434DVD User Manual
Polar GPS Receiver V650 User Manual
Porter Cable Drill 2610 User Manual
Poulan Snow Blower PR521 User Manual