R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WT200
IMPORTANT MANUAL -- Do not throw away
MANUAL IMPORTANTE -- No lo descarte
MANUEL IMPORTANT -- À Conserver
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
530086795
10/1/01
Copyright E2001 WCI Outdoor Products, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available as an optional part. If a spark arrest-
D Never place any object in the air intake open- ing screen is required in your area, contact
ing as this could restrict proper air flow and your authorized service dealer for the correct
cause damage to the unit.
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulations.
D Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
D To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
ASSEMBLY
D Use only for jobs explained in this manual.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
D Use only recommended Poulanr replace-
ment parts; use of any other parts may void
your warranty and cause damage to your
unit.
WARNING: If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
D A standard screwdriver is required for as-
sembly.
D Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by manufac- BLOWER TUBE ASSEMBLY
turer for use with your unit.
D Align the rib on the blower tube with the
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
groove in the blower outlet; slide the tube
into place.
NOTE: Tube clamp must be loose enough to
allow blower tube to be inserted in blower out-
let. Loosen tube clamp by turning knob coun-
D Store in a dry area out of reach of children.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered land in the above
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must be con-
structed, equipped, and maintained for the
prevention of fire. Check with your state or lo-
Blower
Blower
Outlet
Tube
Groove
Rib
D Tighten the tube clamp by turning the knob
clockwise.
D To remove the tube, turn the knob counter-
clockwise to loosen clamp; remove tube.
VACUUM BAG ASSEMBLY
D Open the zipper on the vacuum bag and in-
sert the elbow tube.
D Push the small end of the elbow tube
through the small opening in the bag.
Elbow
Tube
Small
Opening
Zipper
Opening
Rib
NOTE: Make sure edge of the small opening
cal authorities for regulations pertaining to is flush against the flared area of the elbow
these requirements. Failure to follow these tube, and the rib on the elbow tube is on the
requirements is a violation of the law. This unit bottom.
-- 3 --
Download from Www.Somanuals.com. All Manuals Search And Download.
D Close the zipper on the bag. Make sure the
zipper is closed completely.
D Remove blower tube from engine.
Knob
Rib
Hooks
Groove
D When converting back to the blower fea-
ture, make sure latch on the vacuum inlet
cover is securely fastened.
SHOULDER STRAP ADJUSTMENT
D Hold the unit as shown.
D Pass the shoulder strap over your head and
onto your right shoulder.
D Insert the elbow tube into the blower outlet.
Make sure elbow tube rib is aligned with the
blower outlet groove.
D Extend your left arm toward the rear of the
vacuum bag.
D Turn clamp knob clockwise to tighten.
D Adjust shoulder strap until the vacuum bag/
shoulder strap seam lies between your
thumb and index finger.
D Make sure air flows freely from the elbow
tube into bag. If bag is kinked, the unit will
not operate properly.
VACUUM TUBE ASSEMBLY
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury.
D Align the lower vacuum tube as shown.
Push lower vacuum tube into upper vacu-
um tube.
Upper Vacuum
Tube
Lower Vacuum Tube
D Insert a screwdriver into the latch area on
the vacuum inlet cover.
Blower
Outlet
Latch
Ar
Latch Area
Vacuum
Inlet Cover
USING YOUR UNIT
WARNING: You MUST make sure
the tubes are secure before using the unit.
D Gently tilt the handle of the screwdriver to-
ward the back of the unit while pulling up on
the vacuum inlet cover with your other
hand.
D Hold the vacuum inlet cover open until up-
per vacuum tube is installed.
OPERATING POSITION
ye
otec
Vacuum Inlet
Retaining Post
Vacuum
Inlet
Blower
Vacuum
Cover
OPERATING TIPS
D Place the hooks on the vacuum tube on the S While vacuuming or blowing debris, hold
retaining posts; pivot tube into position. Se-
cure vacuum tube by turning the knob
clockwise until tight.
the unit with the muffler side facing away
from your body and clothes (see illustration
above).
-- 4 --
Download from Www.Somanuals.com. All Manuals Search And Download.
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
STARTING
S To reduce the risk of injury associated with
contacting rotating parts, stop the engine be-
fore installing or removing attachments. Do
not operate without guard(s) in place.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S Use rakes and brooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
BEFORE STARTING THE ENGINE
D Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
STARTING POSITION
Blower
WARNING: When starting engine,
hold the unit as illustrated. Do not set unit on any
surface except a clean, hard area when starting
engine or while engine is running. Debris such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
S Use the full blower nozzle extension so the
air stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
FUELING
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
WARNING: Remove fuel cap slowly
when refueling.
S Move throttle lever to the
position.
This engine is certified to operate on un-
leaded gasoline. Gasoline must be mixed
with a good quality synthetic 2--cycle air--
cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand syn-
thetic oil is recommended. A 40:1 ratio is ob-
tained by mixing 3.2 ounces of oil with 1 gallon
of unleaded gasoline. When mixing fuel fol-
low the instructions printed on the container.
Always read and follow the safety rules under
HANDLE FUEL WITH CAUTION.
S Move choke lever to the FULL CHOKE
position.
S Slowly press the primer button 8 times.
T
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
Choke Lever
S Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30_ F, 8 pulls).
NOTE: If engine attempts to start before the
th
5
pull, go to next step immediately.
S Move the choke lever to the HALF CHOKE
position.
-- 5 --
Download from Www.Somanuals.com. All Manuals Search And Download.
S Pull the starter rope sharply until the engine S Vacuum Bag -- Do not use vacuum bag if it
is torn or damaged.
runs, but no more than 5 pulls (below 30_ F,
10 pulls). Run engine for 5 seconds, then
move choke lever to the RUN position.
INSPECT AND CLEAN UNIT AND
DECALS
S Allow the unit to run for 30 more seconds at
the RUN position before moving the throttle
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
lever to
position.
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
STARTING A WARM ENGINE
S Move throttle lever to the
position.
S Pull starter rope sharply until engine runs,
but no more than 5 pulls.
Air Filter
Cover
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
STARTING A FLOODED ENGINE
S Move the choke lever to the RUN position.
S Move throttle lever to the
position.
S Pull rope to clear engine of excess fuel.
This could require pulling the starter rope
many times.
If unit still doesn’t start refer to the TROUBLE-
SHOOTING TABLE or call 1-800-554-6723.
Screws
Air Filter
Cleaning the air filter:
MAINTENANCE
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean or replace
air filter after every 5 hours of operation or
yearly, whichever comes first.
WARNING: Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
S Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
S Remove parts as illustrated.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
S Wash the filter in soap and water.
S Allow filter to dry.
S Apply a few drops of oil to the filter; squeeze
filter to distribute oil.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
S Replace parts.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
S Twist, then pull off spark plug boot.
S Remove spark plug from cylinder and dis-
card.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Muffler
S Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
S Reinstall the spark plug boot.
CHECK FOR DAMAGED OR WORN
PARTS
REPLACE FUEL FILTER
To replace fuel filter, drain unit by running it dry
of fuel, then remove fuel cap from tank. Pull fil-
ter from tank and remove it from the fuel line.
Install new fuel filter on fuel line; reinstall
parts.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
-- 6 --
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
We recommend all service and adjustments
not listed in this manual be performed by an
authorized service dealer.
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Adjusting the carburetor is a complicated
task. We recommend that you take your unit
to an an authorized service dealer. Damage
will occur if you turn the needles beyond the
limiter stops.
Fuel Line
Fuel Filter
CHECK MUFFLER MOUNTING
SCREWS
STORAGE
Once each year, ensure muffler mounting
screws are secure and tightened properly to
prevent damage.
Mounting
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
Screw
Holes
Muffler Cover
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
Screws
S Store unit and fuel well out of the reach of
children.
S Loosen and remove the 2 screws from the
muffler cover.
NEED ASSISTANCE?
S Remove the muffler cover.
S Tighten the 2 muffler mounting screws se-
curely.
NEED ASSISTANCE?
Call: 1-800-554-6723.
S Reinstall muffler cover and 2 screws. Tight-
en securely.
NEED A SERVICE PART?
Contact your authorized service dealer.
-- 7 --
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
REMEDY
S Engine flooded.
S See “Starting Instructions.”
S Fill tank with correct fuel mixture.
S Install new spark plug.
S Fuel tank empty.
S Spark plug not firing.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S Compression low.
S Contact an authorized service dealer.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
S Contact an authorized service dealer.
Engine will not
idle properly.
S Carburetor requires adjustment.
S Crankshaft seals worn.
S Compression low.
S Air filter dirty.
S Clean or replace air filter.
Engine will not
accelerate,
lacks power, or
dies under a
load.
S Fuel not reaching carburetor.
S Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
S Spark plug fouled.
S Clean or replace spark plug; re-gap.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
S Contact an authorized service dealer.
S Carburetor requires adjustment.
S Carbon build up.
S Compression low.
S Adjust choke.
S Choke partially on.
Engine
S Empty fuel tank and refill with
correct fuel mixture.
S Fuel mixture incorrect.
smokes
excessively.
S Clean or replace air filter.
S See “Carburetor Adjustments.”
S Air filter dirty.
S Carburetor requires adjustment.
S See “Fueling Your Unit.”
S Fuel mixture incorrect.
S Spark plug incorrect.
S Carburetor requires adjustment.
S Carbon build up.
Engine
runs hot.
S Replace with correct spark plug.
S See “Carburetor Adjustments.”
S Contact an authorized service dealer.
will wear and require replacement with reason-
able use during the warranty period. This war-
ranty does not cover predelivery setup or nor-
mal adjustments explained in the instruction
manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS NORTH
AMERICA, Division of WCI Outdoor Prod-
ucts, Inc., warrants to the original purchaser
that each new Poulanr brand gasoline tool or
attachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline prod-
uct or attachment as follows from the original
date of purchase.
2 YEARS-- Parts and Labor, when used for
household purposes.
90 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper ELECTROLUX HOME PRODUCTS NORTH
handling, improper maintenance, or the use of AMERICA’S policy is to continuously improve
accessories and/or attachments not specifically its products. Therefore, ELECTROLUX HOME
recommended by ELECTROLUX HOME
PRODUCTS NORTH AMERICA for this tool.
PRODUCTS NORTH AMERICA reserves the
right to change, modify, or discontinue models,
Additionally, this warranty does not cover tune- designs, specifications, and accessories of all
ups, spark plugs, filters, starter ropes, starter products at any time without notice or obligation
springs, cutting line, or rotating head parts that to any purchaser.
-- 8 --
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY COMMENCEMENT DATE:
The warranty period begins on the date the
lawn and garden equipment engine is pur-
chased. LENGTH OF COVERAGE: This
warranty shall be for a period of two years
from the initial date of purchase. WHAT IS
COVERED: REPAIR OR REPLACEMENT
OF PARTS. Repair or replacement of any
warranted part will be performed at no charge
to the owner at an approved POULAN/WEED
EATER servicing center. If you have any
questions regarding your warranty rights and
U.S. EPA
EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
Protection Agency and POULAN/WEED
EATER, DIVISION OF WCI OUTDOOR
PRODUCTS, INC., are pleased to explain the
emissions control system warranty on your
lawn and garden equipment engine. All new responsibilities, you should contact your
utility and lawn and garden equipment en- nearest authorized service dealer center or
gines must be designed, built, and equipped call
POULAN/WEED
EATER
at
to meet the stringent anti--smog standards. 1--800--554--6723 WARRANTY PERIOD:
POULAN/WEED EATER must warrant the
emission control system on your lawn and
Any warranted part which is not scheduled for
replacement as required maintenance, or
garden equipment engine for the periods of which is scheduled only for regular inspection
time listed below provided there has been no to the effect of “repair or replace as neces-
abuse, neglect, or improper maintenance of sary” shall be warranted for 2 years. Any war-
your lawn and garden equipment engine. ranted part which is scheduled for replace-
Your emission control system includes parts
ment as required maintenance shall be war-
such as the carburetor and the ignition sys- ranted for the period of time up to the first
tem. Where a warrantable condition exits, scheduled replacement point for that part.
POULAN/WEED EATER will repair your lawn
DIAGNOSIS: The owner shall not be
and garden equipment engine at no cost to charged for diagnostic labor which leads to
you. Expenses covered under warranty in- the determination that a warranted part is de-
clude diagnosis, parts and labor. MANUFAC- fective if the diagnostic work is performed at
TURER’S WARRANTY COVERAGE: If any
an approved POULAN/WEED EATER serv-
emissions related part on your engine (as icing center. CONSEQUENTIAL DAM-
listed under Emissions Control Warranty
AGES: POULAN/WEED EATER may be li-
Parts List) is defective or a defect in the mate- able for damages to other engine compo-
rials or workmanship of the engine causes the nents caused by the failure of a warranted
failure of such an emission related part, the part still under warranty. WHAT IS NOT COV-
part will be repaired or replaced by POULAN/
WEED EATER. OWNER’S WARRANTY
RESPONSIBILITIES: As the lawn and gar-
ERED: All failures caused by abuse, neglect,
or improper maintenance are not covered.
ADD--ON OR MODIFIED PARTS: The use
den equipment engine owner, you are re- of add--on or modified parts can be grounds
sponsible for the performance of the required for disallowing a warranty claim. POULAN/
maintenance listed in your instruction manu- WEED EATER is not liable to cover failures of
al. POULAN/WEED EATER recommends
warranted parts caused by the use of add--on
that you retain all receipts covering mainte- or modified parts. HOW TO FILE A CLAIM: If
nance on your lawn and garden equipment
engine, but POULAN/WEED EATER cannot
you have any questions regarding your war-
ranty rights and responsibilities, you should
deny warranty solely for the lack of receipts or contact your nearest authorized service cen-
for your failure to ensure the performance of ter or call POULAN/WEED EATER at
all scheduled maintenance. As the lawn and 1--800--554--6723. WHERE TO GET WAR-
garden equipment engine owner, you should RANTY SERVICE: Warranty services or re-
be aware that POULAN/WEED EATER may
deny you warranty coverage if your lawn and
pairs shall be provided at all POULAN/WEED
EATER service centers. call:
garden equipment engine or a part of it has 1--800--554--6723. MAINTENANCE, RE-
failed due to abuse, neglect, improper mainte- PLACEMENT AND REPAIR OF EMISSION
nance, unapproved modifications, or the use RELATED PARTS: Any POULAN/WEED
of parts not made or approved by the original EATER approved replacement part used in
equipment manufacturer. You are responsi- the performance of any warranty mainte-
ble for presenting your lawn and garden
nance or repair on emission related parts will
equipment engine to a POULAN/WEED EAT- be provided without charge to the owner if the
ER authorized repair center as soon as a
part is under warranty. EMISSION CON-
problem exists. Warranty repairs should be TROL WARRANTY PARTS LIST: Carbure-
completed in a reasonable amount of time, tor, Ignition System: Spark Plug (covered up
not to exceed 30 days. If you have any ques-
tions regarding your warranty rights and re-
to maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT: The owner is
sponsibilities, you should contact your near- responsible for the performance of all re-
est authorized service dealer or call POU-
LAN/WEED EATER at 1--800--554--6723.
quired maintenance as defined in the instruc-
tion manual.
-- 9 --
Download from Www.Somanuals.com. All Manuals Search And Download.
|