ESPAÑOL: PÁGINA 23
FRANÇAISE : PAGE 43
12" Compound Laser Miter Saw
Instruction
Manual
MODEL 3802L
IMPORTANT
Please make certain that the person who is to use
this equipment carefully reads and understands
these instructions before starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. _____________________________________
Type __________________________________________
Serial No.______________________________________
Part No. 906984 - 07-20-04
Copyright © 2004 PORTER-CABLE Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR
SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
CALIFORNIA PROPOSITION 65
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool’s application and limitations as well as the specific
hazards peculiar to it.
15. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
16. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by
Porter-Cable may cause hazards or risk of injury to
persons.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION. Wear safety
glasses. Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses. Also use
face or dust mask if cutting operation is dusty. These
safety glasses must conform to ANSI Z87.1
requirements. NOTE: Approved glasses have Z87
printed or stamped on them.
17. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in “OFF” position before plugging in
power cord. In the event of a power failure, move
switch to the “OFF” position.
18. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally
contacted.
19. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly
and perform its intended function – check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
4. REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it “on”.
5. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose
them to rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY. All children
and visitors should be kept a safe distance from work
area.
20. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter
only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
22. STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE WHEN OPERATING A
POWER TOOL. DO NOT USE TOOL WHILE TIRED
OR UNDER THE INFLUENCE OF DRUGS,
8. MAKE WORKSHOP CHILDPROOF – with padlocks,
master switches, or by removing starter keys.
9. DON’T FORCE TOOL. It will do the job better and be
safer at the rate for which it was designed.
10. USE RIGHT TOOL. Don’t force tool or attachment to do
a job for which it was not designed.
ALCOHOL, OR MEDICATION.
A
moment of
11. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught
in moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
inattention while operating power tools may result in
serious personal injury.
23. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted,
connected or reconnected.
24. THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper
dust removal. Use wood dust collection systems
whenever possible.
12. SECURE WORK. Use clamps or a vise to hold work
when practical. It’s safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and balance
at all times.
14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
SAVE THESE INSTRUCTIONS.
Refer to them often and
use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY RULES FOR MITER SAWS
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. DO NOT OPERATE THIS MACHINE UNTIL it is
19. NEVER CUT FERROUS METALS or masonry.
20. NEVER RECUT SMALL PIECES.
21. NEVER LOCK THE SWITCH in the “ON” position.
22. NEVER APPLY LUBRICANT to a running blade.
23. DO NOT PERFORM FREE-HAND OPERATIONS.
Hold the work firmly against the fence and table.
Use clamps to hold the work when possible.
assembled and installed according to the instructions.
2. OBTAIN ADVICE from your supervisor, instructor, or
another qualified person if you are not familiar with the
operation of this machine.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
MOUNT THE TOOL SECURELY to a stable supporting
surface prior to operation
4
24. PROPERLY SUPPORT LONG or wide workpieces.
25. AFTER COMPLETING CUT, release power switch and
wait for coasting blade to come to a complete stop
before returning saw to raised position.
26. TURN OFF TOOL AND ALLOW THE BLADE TO
COME TO A COMPLETE STOP prior to cleaning the
blade area or removing debris in the path of the blade.
A coasting blade can be dangerous.
27. TURN OFF TOOL AND ALLOW BLADE TO COME TO
A COMPLETE STOP before removing or securing
workpiece, changing workpiece angle, or changing the
angle of the blade.
28. NEVER PERFORM LAYOUT, ASSEMBLY, or set-up
work on the table/work area when the machine is
running.
29. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting or
changing set-ups, or when making repairs.
30. TURN THE MACHINE “OFF”, disconnect the machine
from the power source, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN
THE “OFF” POSITION to prevent unauthorized use.
5. USE THE GUARDS WHENEVER POSSIBLE. Check
to see that they are in place, secured, and working
correctly.
6. USE ONLY CROSSCUT SAW BLADES. Use only zero-
degree or negative hook angles when using carbide-
tipped blades. Do not use blades with deep gullets.
These can deflect and contact the guard.
7. USE ONLY BLADES OF THE CORRECT SIZE AND
TYPE specified for this tool.
8. USE A SHARP BLADE. Check blade to see if it runs
freely and is free from vibration.
9. INSPECT BLADE FOR CRACKS or other damage prior
to operation. Replace cracked or damaged blade
immediately.
10. CLEAN THE BLADE AND BLADE FLANGES prior to
operation. Check for any damage and tighten the arbor
nut securely.
11. USE ONLY BLADE FLANGES specified for this tool.
12. CLEAR THE AREA OF FLAMMABLE LIQUIDS and/or
gas prior to operation.
13. CLEAN THE MOTOR AIR SLOTS of chips and
sawdust.
31. ADDITIONAL INFORMATION regarding the safe and
proper operation of this tool is available from the
Power Tool Institute, 1300 Summer Avenue, Cleveland,
OH 44115-2851. Information is also available from the
National Safety Council, 1121 Spring Lake Drive,
Itasca, IL 60143-3201. Please refer to the American
National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the
14. TIGHTEN THE TABLE CLAMP HANDLE and any other
clamps prior to operation.
15. NEVER START THE TOOL with the workpiece against
the blade.
16. KEEP HANDS out of path of saw blade. Clamp all
workpieces that would require your hand to be in the
“Table Hazard Zone” (within the red lines).
U.S. Department
Regulations.
of
Labor
OSHA 1910.213
17. ALLOW THE MOTOR to come to full speed prior to
starting cut.
18. NEVER REACH AROUND or behind the saw blade.
ADDITIONAL SAFETY RULES FOR THE LASER
1.
2.
LASER LIGHT - DO NOT STARE INTO BEAM,
APERTURE, or into a reflection from a mirror-like surface Fig. 1&1A.
AVOID EXPOSURE - LASER LIGHT IS EMITTED
FROM FRONT GUARD APERTURE. Use of controls or
adjustments, or performance of procedures other than those
specified herein may result in hazardous laser light exposure.
3.
4.
DO NOT DISASSEMBLE LASER MODULE. The
laser is a CLASS II LASER PRODUCT that can emit laser power
up to 1 mW MAX at 635 nm, which could result in exposure with
the module disassembled. The laser unit complies with 21 CFR
1040.10 and 1040.11.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Fig. 1
SAVE THESE INSTRUCTIONS. Refer to them often and
use them to instruct others.
Fig. 1A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-
prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
POLARIZED PLUGS: To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus
or minus 5 percent of that shown on the specification plate of the tool. Several models, however, are designed for A.C.
current only. Refer to the specification plate on your tool for proper voltage and current rating.
Do not operate your tool on a current where the voltage is not within correct limits. Do not operate tools
rated A.C. on a D.C. current. To do so may seriously damage the tool.
REPLACEMENT PARTS
When servicing, use only identical replacement parts.
EXTENSION CORDS
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
Total Length
Gauge of
Use proper extension cords. Make sure your extension
cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the
current of the machine. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating. Fig. D, shows the correct gauge to use
depending on the cord length. If in doubt, use the next
heavier gauge. The smaller the gauge number, the
heavier the cord.
Volts
of Cord in Feet
Extension Cord
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
up to 25
25-50
50-100
100-150
up to 25
25-50
50-100
100-150
up to 25
25-50
50-100
100-150
up to 25
25-50
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG
14 AWG
12 AWG
12-16
12-16
12-16
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. D
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Model 3802L is a high capacity, 12" compound laser miter saw designed to cut wood and non-ferrous
metals. This unit incorporates the latest technology DUAL LASERLOC line-of-cut indicator feature. It can crosscut 8"
™
x 2¼" and 7" x 3¼", miter at 45° both left and right 5¼" x 2¼", bevel at 45° left 6¼" x 2¼" and 8" x 1¼", and compound
45° x 45°, 5¼" x 2 1/2" and 4¼" x 2¼". It has positive miter stops at 0°, 15°, 22.5°, 31.62°, and 45° both left and right,
and bevel stops at 0° and 45° left.
NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations
contained in the manual are representative only and may not depict the actual color, labeling, or accessories,
and are intended to illustrate technique only.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
4
2
3
5
9
1
6
11
8
7
14
12
13
Fig. 2
Fig. 3
10
1. Miter Saw
2. Extension table
3. Fence slide
4. Fence slide support
5. Dust bag
6. 1/2" Arbor and fence wrench
7. 1/4" hex wrench
8. Open end 7/16" wrench
9. Lock handle for sliding fence
10. 5/16" flat washer
11 5/16" lock washer
12 5/16 - 18 x 1 1/4" long hex head screw (2)
13 5/16 - 18 x 3/4" long hex head screws (2)
14. 1/8" hex wrench
UNPACKING AND CLEANING
1. Carefully remove the machine from the carton. Retain all packing materials until you have inspected and
satisfactorily operated the machine.
Do not operate this machine until you read and understand the entire instruction manual.
2. Place the machine on a firm, level surface with extra room for handling and proper support of the workpiece.
3. Familiarize yourself with all features and controls explained in this manual.
4. The machine is shipped with the cuttinghead locked in the down position and the table rotated to 45° left, Fig. 2. To
release the head and move it to the operating position, see “MOVING CUTTINGHEAD TO THE UP POSITION” and
“MOVING THE TABLE TO THE 0° CUT-OFF POSITION” in this manual (Fig. 5 & 7).
ASSEMBLY
ASSEMBLY TOOLS REQUIRED
1/2" arbor and fence wrench (supplied)
7/16"Open end wrench (supplied)
ASSEMBLY TIME ESTIMATE
Assembly time for this unit is approximately 30 minutes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MOVING CUTTINGHEAD TO THE UP POSITION
1. Pull out the cuttinghead lockpin (A) Fig. 4, and move the cuttinghead (B) to the up position.
2. Fig. 5 illustrates the lockpin (A) pulled out and the cuttinghead (B) in the up position.
B
A
B
A
Fig. 4
Fig. 5
MOVING TABLE TO THE 0° CUT-OFF POSITION
1. Rotate locking knob (A) Fig. 6 counter-clockwise as far as it will go. Depress the lever (B) and rotate the table (C) to the 0°
straight cut-off position, release the lever (B), and tighten the locking knob (A).
2. Fig. 7 illustrates the table (C) in the 0° straight cut-off position.
3. For proper operation and adjustment of the table, refer to sections, “ROTATING TABLE FOR MITER CUTTING”, and
“ADJUSTING SLIDING FIT BETWEEN MOVABLE TABLE AND BASE.”
C
A
B
C
Fig. 6
Fig. 7
ATTACHING EXTENSION TABLE AND FENCE SLIDE
1. Attach flat washers to the two 5/16-18 x 3/4” screws (A) Fig. 8. Thread the screws into the holes on left side of the saw
(Figs. 8 & 9).
NOTE: Turn the screws only a few threads for further adjustment.
2. Attach the table extension (B) Figs. 8 and 9 to left side of saw table, making sure that the groove of the table extension
(B) is inside the flat washers (C) Fig. 8.
3. Use a straight edge (C) Fig. 10 to ensure that the extension table (B) is even with the saw table (D). Tighten the two screws
(C) Fig. 9.
A
B
B
C
Fig. 8
Fig. 9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach the fence slide support (E) Fig. 11 to the extension table (B) by using the two 5/16-18 x1-1/4” hex head screws,
5/16” lockwashers, and 5/16” flat washers (F). Insert the two screws up through the two holes (G) in the table extension
and thread them into the two threaded holes (H) on the bottom of the fence slide support.
NOTE: Leave the screws loose for now.
5. Use a straight edge (C) Fig. 12 to align the fence slide support (E) with the saw fence (J), and tighten the two screws.
6. Position the fence slide (K) Fig. 13 on top of the saw fence (J) and the fence slide support (E). Move the fence slide (K)
back and forth several times to check the alignment of the fence slide support (E). Make any necessary final adjustments
to the fence slide support.
7. Remove the screw and spring (E) Fig. 14 and the locking handle (M) from the locking stud (N).
8. PLace a 1/4" flat washer (O) Fig. 14 on the locking stud (N) and insert locking stud (N) Fig. 15 through the slot in the fence
slide. Screw the locking stud into threaded hole in the fence slide support (E).
9. Place the lock handle (M) Fig. 16 on the stud and replace the screw and spring (L) that were removed in STEP 7.
NOTE: The lock handle (M) is spring-loaded and can be repositioned by lifting up on handle.
H
C
E
C
G
B
E
J
F
B
D
F
Fig. 10
Fig. 12
Fig. 11
N
E
K
N
E
O
J
E
M
Fig. 13
Fig. 14
Fig. 15
A
L
B
M
Fig. 16
Fig. 17
ATTACHING DUST BAG
Depress the spring clips (A) Fig. 17 of the dust bag (B) and clip the dust bag (B) over the ribs of the dust chute.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING CONTROLS AND ADJUSTMENTS
FASTENING MACHINE TO SUPPORTING SURFACE
Before operating your miter saw, firmly mount it to a workbench
or other supporting surface. Four holes (A) Fig. 18 are provided for
fastening the saw to a supporting surface.
When frequently moving the saw from place to place, mount the
saw on a 3/4” piece of plywood. The saw can then be easily
moved from place to place and the plywood can be clamped to
the supporting surface using “C” clamps.
A
Fig. 18
STARTING AND STOPPING MACHINE
To start the machine, depress the switch trigger (A) Fig. 19. To stop the machine, release the switch trigger.
This saw is equipped with an automatic electric blade brake. As soon as the switch trigger (A) Fig. 19 is released, the electric
brake is activated and stops the blade in seconds.
A rotating saw blade can be dangerous. After completing the cut, release the switch trigger (A) Fig. 19
to activate the blade brake. Keep the cuttinghead down until the blade has come to a complete stop.
The torque developed during braking may loosen the arbor screw. The arbor screw should be checked
periodically and tightened if necessary.
LOCKING SWITCH IN THE “OFF” POSITION
IMPORTANT: When the miter saw is not in use, the switch should be locked in the "OFF" position, using a padlock (B) Fig.
20 with a 3/16" diameter shackle to prevent unauthorized use of the saw.
In the event of a power outage, always lock switch in “OFF” position until the main power is restored.
A
B
Fig. 20
Fig. 19
ROTATING TABLE FOR MITER CUTTING
1. This miter saw will cut any angle from 0° to 47° right and left. Turn the locking knob (A) Fig. 21 counter-clockwise, depress
the lock lever (B), and rotate the table.
2. The compound miter saw is equipped with positive stops at 0°, 15°, 22.5°, 31.62°, and 45° left and right.
3. The center line (C) Fig. 22 on the cursor indicates the actual angle of cut. Each scale line (B) represents 1°. When the center
line (C) is moved from one line to the next on the scale, the angle of the cut is changed by 1°.
4. The pointer is provided with two additional lines (D) and (E) Fig. 22. This allows movement of 1/2°. For example, assume
the center line (C) is pointing to the 10° mark on the scale, and the angle of cut is 1/2° to the right. Move the control arm
until the right line (E) lines up with the next line on the scale. If you change the angle of cut 1/2° to the left, use the left line
(D).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
D
E
B
C
Fig. 21
Fig. 22
ADJUSTING SLIDING FIT BETWEEN MOVABLE TABLE AND BASE
DISCONNECT THE MACHINE FROM THE
POWER SOURCE.
To adjust the sliding fit between the movable table and the base,
turn the nut (A) Fig. 23 clockwise to increase the sliding fit
(opposite to decrease the fit). This adjustment should not be so
tight that it restricts the rotating movement of the table, or so
A
loose that it affects the accuracy of the saw.
Fig. 23
ADJUSTING FENCE 90° TO BLADE
IMPORTANT: Before making this adjustment, set the blade at 0° to the table. See section “ADJUSTING 0° AND 45° BEVEL
POSITIVE STOPS.”
DISCONNECT THE MACHINE FROM THE POWER SOURCE.
1. Rotate the movable table so that the blade is 90° to the fence and the positive stop is set for 0°.
2. Place one end of a framing square (A) Fig. 24 against the front of the fence (B) and the other end against the blade (C),
with the blade locked in the down position. The fence should be 90° to the blade.
3. If an adjustment is necessary, the fence (B) Fig. 24 can be adjusted by loosening four screws (two of which are shown at
D), that attach the fence to the base. Use the wrench supplied. Adjust the fence (B), and tighten the four screws (D).
4. When the fence is 90° to the blade, adjust the cursor (F) Fig. 25, so that the pointer is aligned with the 0° mark on the
scale by loosening two screws, (G), adjusting cursor (F) and tightening screws (G).
G
C
D
F
B
A
Fig. 24
Fig. 25
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE HAZARD ZONE
The area inside the two red lines (A) Fig. 26 on
the table is designated as a HAZARD ZONE.
Never place your hands inside this area while
the tool is being operated. Always use a clamp
to secure short workpieces.
A
Fig. 26
TILTING CUTTINGHEAD FOR BEVEL CUTTING
DISCONNECT THE MACHINE FROM THE POWER SOURCE.
IMPORTANT: Move the sliding fence to the left to provide clearance for the blade and guard. The degree of tilt determines
how far to move the sliding fence. Refer to the section “ADJUSTING SLIDING FENCE.”
1. The cuttinghead can be tilted to cut any bevel angle from 90° to 45° left bevel. Loosen the bevel lock handle (A) Fig. 27,
tilt the cuttinghead (B) to the desired angle, and tighten the lock handle (A).
2. Positive stops are provided to rapidly position the saw blade at 90° and 45°. Refer to the section of this manual titled
“ADJUSTING 90° AND 45° BEVEL POSITIVE STOPS.” The bevel angle of the cutting arm is determined by the position
of the pointer (C) Fig. 28 on scale (D).
3. In addition, a marked indicator (M) Fig. 28 is provided on the bevel scale (33.9°) for cutting crown moulding. Refer to the
“CUTTING CROWN MOULDING” section of this manual.
M
B
D
A
C
Fig. 27
Fig. 28
ADJUSTING SLIDING FENCE
The sliding fence (Fig. 29) provides support for extra large workpieces used with your saw and should always be set as close
as possible to the saw blade. When miter cutting (blade 90° to the table and at an angle to the right or left), set the fence all the
way toward the blade (Fig. 29). When bevel cutting, however (blade tilted at an angle to the table), move the fence (A) Fig. 30
away from the blade to allow for proper clearance for the saw blade and guard. To reposition the fence, loosen the lock handle
(B), and slide the fence (A) to the desired location. Tighten the lock handle (B).
NOTE: The lock handle (B) is spring-loaded and can be repositioned. Pull up on handle to reposition it on the serrated nut
located underneath handle.
B
A
Fig. 29
Fig. 30
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING CHIP DEFLECTOR
DISCONNECT THE MACHINE FROM THE
POWER SOURCE.
A
B
A chip deflector (A) Fig. 31 is supplied to help prevent scrap or
cut-off pieces from entering the upper blade guard. Adjust the
chip deflector (A) so that it is almost touching the side of the
blade. Loosen the screw (B), adjust the chip deflector (A), and
tighten the screw (B).
Fig. 31
ADJUSTING 0° AND 45° BEVEL POSITIVE STOPS
DISCONNECT THE MACHINE FROM THE POWER SOURCE.
1. Adjust the saw so that both the bevel and miter pointers are set at 0°. Tighten the bevel lock handle and lock the
cuttinghead in the down position.
2. Place one end of a square (A) Fig. 32 on the table and the other end against the blade. The blade should be 90° to the
table.
3. To adjust, loosen the bevel lock handle (H) Fig. 33. Loosen the locknut (B) and turn the adjusting screw (C) with the
provided wrenches until the blade is 90° to the table. Tighten the locknut (B) and the bevel lock handle (H).
4. When the blade is 90° to the table, adjust the pointer to line up with the 0° mark on the bevel scale.
5. Loosen the bevel lock handle (H) Fig. 33, and move the cuttinghead all the way to the left bevel position and tighten the
bevel lock handle.
6. Use a square (A) Fig. 34 to see if the blade is at 45° to the table.
7. To adjust, loosen the bevel lock handle. Loosen the locknut (E) Fig. 35 and turn the adjusting screw (F) with the provided
wrenches, until the blade is 45° to the table. Tighten the locknut (E) and the bevel lock handle.
A
H
C
B
Fig. 32
Fig. 33
F
A
E
Fig. 34
Fig. 35
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING SLIDING FIT BETWEEN TRUNNION AND BEVEL BRACKET
After a long period of time, the sliding fit between the trunnion and the bevel bracket may need to be adjusted. Adjust the sliding
fit by tightening the adjusting nut (C) Fig. 36, located underneath the bevel lock (A) Fig. 36 and collar (B) Fig. 36.This adjustment
should not be so tight that it restricts the tilting movement of the trunnion when bevel cutting, or so loose that it affects
the accuracy of the saw cut.
ADJUSTING THE TENSION OF CUTTINGHEAD RETURN SPRING
The cuttinghead return spring tension was adjusted at the factory to make the cuttinghead return to the "up" position after
a cut is made. To adjust the spring tension, turn the adjusting screw (A) Fig. 37 clockwise to increase or counterclockwise
to decrease the spring tension.
ADJUSTING SLIDING FIT BETWEEN CUTTINGHEAD ARM AND TRUNNION
After a long period of time, an adjustment of the sliding fit between the cuttinghead arm (B) Fig. 37, and the trunnion (C)
may be necessary. To adjust, tighten the nut (D). This adjustment should not be so tight that it restricts the sliding
movement of the cuttinghead arm (B) or so loose that it affects the accuracy of the saw cut.
C
C
B
B
A
A
D
Fig. 36
Fig. 37
ADJUSTING DOWNWARD TRAVEL OF SAW BLADE
DISCONNECT THE MACHINE FROM THE
POWER SOURCE.
1. The downward travel of the saw blade can be limited to
prevent the saw blade from contacting any metal surfaces
of the machine. Make this adjustment by loosening the
locknut (A) Fig. 38, and turning the adjusting screw (B) in or
out until other end of the screw (B) contacts the stop at the
full downward travel of the saw blade.
A
B
2. Lower the blade as far as possible. Rotate the blade by
hand to make certain that the teeth do not contact any
metal surfaces. After adjusting, tighten the locknut (A) Fig.
38.
Fig. 38
LASER USE AND ADJUSTMENT
PHILLIPS
SCREW
The DUAL LASERLOC
™
laser units are mounted in a housing
that is fitted into the upper blade guard of the miter saw (Fig.
A). The lasers project a beam of light downward, along both
sides and parallel to the saw blade. This beam of light
produces a line-of-cut indicator (a red outline of where the saw
blade will cut) on the workpiece.
LASER
UNIT
UPPER
BLADE
GUARD
Fig. A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE DUAL LASERLOC
™
LINES
Each of the laser lines have been aligned parallel to the blade at the factory and should not need any adjustment prior
to use. However, left-to-right adjustment to the laser lines may be necessary if you change to a thicker or thinner kerf
blade. For information on changing your blade, refer to the "MAINTENANCE: CHANGING THE BLADE" section of this
manual. To adjust the laser lines to the edge of the cut, follow the instructions below.
HOW THE LASERS WORK
The laser units are mounted in a housing that is fitted into the upper blade guard of the miter saw (Fig. A). The laser units
are aligned to the original equipment blade at the factory and are secured in place. A test cut has been made with each
saw to verify laser setup. If your saw becomes misaligned or you desire additional precision, this guide is intended to
assist you in fine tuning your laser miter saw.
HOW TO CHECK LASER ALIGNMENT
Make sure the saw is set to 0 degrees, miter and bevel, and clamp a 2"x 6" board on the saw. Create a partial test cut
in the workpiece (Fig. C). Turn the laser “ON/OFF” switch (Fig. B) to the “ON” position. Leave the workpiece clamped in
place for the remainder of the adjustment.
Observe the laser CAUTION label (L) Fig. B.
Place a padlock (A) Fig. B (with 3/16" shackle) through the hole in the trigger switch and lock to
prevent accidental motor startup. This padlock MUST remain in place during the adjustment
procedure.
The laser lines are properly positioned when the beams of light fall on the edge of the cut created by the blade (Fig. D).
L
A
PARTIAL
CUT
Fig. C
Fig. B
VERTICAL
ALIGNMENT
SET SCREWS
BRASS
HEX
NUT
Fig. E
Fig. D
TO CHECK FOR ROTATIONAL ALIGNMENT
The rotation of the lines is set parallel at the factory and permanently secured. No user adjustment is available for the
rotational alignment. Never twist the brass hex nuts in Fig. E.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CHECK FOR VERTICAL ALIGNMENT
Fig. G
Fig. F
1. The vertical alignment is set correctly when the lines do not move horizontally (sideways) as the saw head is raised and
lowered. If vertical alignment is correct, go to “TO SET LEFT AND RIGHT KERF ADJUSTMENT”.
2. To adjust, turn the left and right kerf adjustment screws one half turn clockwise. Take off the laser unit cover by removing
the phillips screw on either side of the cover. (Fig. A).
3. Use the 1/8" hex wrench to turn the left or right vertical alignment set screws. If, as the saw head goes from a raised to
a lowered position, the laser line moves horizontally away from the blade, turn the vertical alignment set screw clockwise
to correct. If the laser line moves horizontally towards the blade, turn the vertical alignment set screw counter-clockwise.
(Fig. F)
4. Reinstall the cover removed in STEP 1, and continue to “TO SET LEFT AND RIGHT KERF ADJUSTMENT”.
TO SET LEFT and RIGHT KERF ADJUSTMENT
1. Use the 1/8" hex wrench to turn the left or right kerf
adjustment screws and set the laser lines to either side of
the test cut (Fig. G). To adjust the left line, turn the left kerf
adjustment screw counter-clockwise to move the line
toward the blade and clockwise to move the line away from
the blade. To adjust the right line turn the right kerf
adjustment screw counter-clockwise to move the line
toward the blade and clockwise to move the line away from
the blade. (Fig. H)
L
Observe the laser CAUTION label (L)
Fig. H.
2. Remove the padlock and use the saw normally.
LEFT LASER
ADJUSTMENT
SCREW
RIGHT LASER
ADJUSTMENT
SCREW
Fig. H
DUAL LASERLOC
™
MAINTENANCE
For best laser performance, perform the following maintenance
regularly:
A
DISCONNECT THE MACHINE FROM
THE POWER SOURCE.
B
1. Carefully clean sawdust from each laser lens (A) Fig. J with
a cotton swab (B). Do not use solvents of any kind since
they may damage the lens. Avoid touching sharp points of
the saw blade with your hands or fingers. Dust build-up
can block the laser and prevent it from accurately
indicating the line-of-cut.
Fig. J
2. Remove the blade from the saw and clean pitch build-up
from the blade (Fig. K) Pitch build-up can block the laser
and prevent it from accurately indicating the line-of-cut.
Fig. K
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING LOWER BLADE GUARD
After an extended period of use, the movable lower blade guard
(A) Fig. 39 may not operate smoothly when the cuttinghead is
lowered. You can correct this by adjusting the nut (B) until the
lower blade guard (A) moves freely.
A
Do not over-tighten the nut as this can make
the guard hard to move.
B
Fig. 39
TYPICAL OPERATIONS AND HELPFUL HINTS
1. Before cutting, make certain that the cutting arm and table area are at their correct settings and firmly locked in place.
2. Before cutting, determine that the workpiece is the right size for the saw.
3. Place the workpiece on the table and hold or clamp it firmly against the fence.
4.
If the size of the workpiece would cause your hand to be inside the table hazard zone (see section “TABLE
HAZARD ZONE” FIG. 26), use a clamp to secure the workpiece.
5. For best results, cut at a slow, even cutting rate.
6. Never attempt any freehand cutting (wood that is not held firmly against the fence and table).
AUXILIARY WOOD FENCE
When performing multiple or repetitive cut-off
operations that result in small cut-off pieces (one inch or less), the
saw blade can catch the cut-off pieces and project them out of
the machine or into the blade guard and housing, possibly
causing damage and/or injury. In order to limit the possibility of
personal injury or blade guard damage, an auxiliary wood fence
can be mounted to your saw.
Holes are provided in the fence to attach an auxiliary fence (A) and
A
B
(B) Fig. 40. This auxiliary fence is constructed of straight wood
approximately 1/2” thick by 3” high by 16 inches long as shown
at (B); and 1/2” thick by 5” high by 17” long (A) Fig. 40.
NOTE: The auxiliary fence (A) is used only with the saw blade in
the 0° bevel position (90°) to the table. The auxiliary fence must
be removed for all bevel cuts (blade tilted).
Fig. 40
CUTTING ALUMINUM
Aluminum extrusions (aluminum screens and storm windows) can easily be cut with your miter saw. When cutting aluminum
extrusions, or other sections that can be cut with a saw blade and are within the capacity of the machine, position the material
so that the blade is cutting through the smallest cross-section (Fig. 41). The wrong way to cut aluminum angles is illustrated
in Fig. 42). Be sure to apply a stick wax (similar to Johnson’s stick wax #140) to the blade before cutting any aluminum stock.
This stick wax is available at most industrial mill supply houses. The stick wax provides proper lubrication and keeps chips
from adhering to the blade.
Never apply lubricant to the blade while the blade is running.
CORRECT
INCORRECT
FENCE
FENCE
BLADE
Fig. 41
BLADE
Fig. 42
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING BOWED MATERIAL
1. If the material is bowed, position it on the table as shown in Fig. 43.
2. If the material is positioned the wrong way (Fig. 44), the workpiece will pinch the blade near the completion of the cut.
CORRECT
INCORRECT
Fig. 43
Fig. 44
One of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting both
inside and outside corners on 52°/38° wall angle crown moulding.
1. Move the table to the 31.62° right miter position and lock the table in position. NOTE: A positive stop is provided to
find this angle quickly.
2. Tilt the saw blade to the 33.86° left bevel position and tighten bevel lock handle. NOTE: A triangle indicator is
provided on the bevel scale to find this angle quickly.
3. Place the crown moulding on the table with the CEILING EDGE of the moulding against the fence, and make the
cut, as shown in Fig. 45.
NOTE: The piece of crown moulding used for the outside corner will always be on the right hand side of the blade, as
shown at (A) Fig. 45. The piece of crown moulding used for the inside corner will always be on the left hand side of
the blade, as shown at (B) Fig. 45.
4. To make the matching halves of the inside and outside corners, rotate the table to the 31.62° left miter position.
NOTE: A positive stop is provided to find this angle quickly. The saw blade is already tilted to the 33.86° bevel position
from the previous cut.
5. Place the crown moulding on the table with the WALL EDGE of the crown moulding against the fence and make the
cut. Again, the piece of crown moulding used for the outside corner will always be on the right side of the blade, as
shown at (C) Fig. 46. The piece of crown moulding used for the inside corner will always be on the left side of the
blade, as shown at (D) Fig. 46.
6. Fig. 47 illustrates the two outside corner pieces; (1) being the piece cut at (A) Fig. 45 and (2) being the piece cut at
(C) Fig. 46.
7. Fig. 48 illustrates the two inside corner pieces; (1) being the piece cut at (B) Fig. 45, and (2) being the piece cut at (D)
Fig. 46.
D
C
A
B
Fig. 45
Fig. 46
2
1
1
2
B
D
C
A
Fig. 47
Fig. 48
18
Download from Www.Somanuals.com. All Manuals Search And Download.
45-45 CROWN MOULDING
NOTE: If you are cutting crown moulding that is 45°-45°, follow the same procedure above, with the exception that the
bevel position will always be at 30° and the miter position will be 35-1/4° to the right or left.
OTHER ANGLES
NOTE: The above instructions are assuming the angle between the walls is 90°. If you need help cutting crown moulding
for walls set at angles other than 90°, see the instruction sheet “CUTTING CROWN MOULDING” on the Porter-Cable
WORK SUPPORT EXTENSIONS
For support when cutting long pieces, a work support
extension can be constructed. Fig. 49 illustrates the miter saw
mounted to two standard 2 x 4’s (A). Fasten the four mounting
C
legs (two of which are shown at (B) Fig. 49) to the 2 x 4’s, using
four screws (not supplied) through the four holes in the
mounting legs. The length of the 2 x 4’s (A) can vary,
depending on the kind of work that will need to be cut.
NOTE: Ensure that the top of the support 2 x 4’s are level
with the miter saw table.
This is critical because the distance from the top of the 2 x 4’s
A
B
(A) to the miter saw table varies from saw to saw. In most
cases, standard 2 x 4’s (C) can used. If these are too high, cut
the 2 x 4s (C) to provide this height or use other properly-sized
wood
Fig. 49
TROUBLESHOOTING
For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable
help line at 1-800-487-8665.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHANGING THE BLADE
Use only cross-cutting saw blades. DO NOT use blades with deep gullets as they can deflect and
contact the guard
DISCONNECT THE MACHINE FROM THE POWER SOURCE.
NOTE: Use only 12" diameter blades with 1" arbor holes that are rated for 4000 RPM or higher.
1. Loosen the screw (A) Fig. 50 with the supplied wrench (B).
2. Rotate the arbor cover (C) Fig. 51, and lower the guard (D) Fig. 51 to the rear, exposing the arbor screw (E).
3. Remove the arbor screw (E) Fig. 51 by turning the screw clockwise with the supplied wrench, while at the same time,
pressing in on the arbor lock (F) Fig. 52. Remove the outside blade flange (G) Fig. 51, and saw blade. Do not remove the
inside blade flange.
4. Attach the new saw blade, making certain that the teeth of the saw blade are pointing down at the front, and attach
outside blade flange (G) Fig. 51. Check to see that the flats on outside blade flange are engaged with the flats on the arbor
shaft.
5. Thread the arbor screw (E) Fig. 51 into the saw arbor by turning the screw (E) counterclockwise as far as possible by hand.
Tighten the arbor screw (E) with the supplied wrench while at the same time pressing in on arbor lock (F) Fig. 52.
6. Rotate the arbor cover (C) Fig. 51, and lower the guard (D) to the front. Tighten the screw (A) that was loosened in STEP
3.
A
F
C
D
G
E
B
Fig. 50
Fig. 51
Fig. 52
BRUSH INSPECTION AND REPLACEMENT
BEFORE INSPECTING OR REMOVING BRUSHES, DISCONNECT THE MACHINE FROM THE
POWER SOURCE.
Brush life varies, depends on the load on the motor. Check the brushes after the first 50 hours of use of a new machine,
or after a new set of brushes has been installed.
After the first check, examine them after about 10 hours of use, until replacement is necessary.
The brush holders (A) Fig. 53, are located on the motor housing opposite each other. Fig. 54, illustrates one of the
brushes removed for inspection. When the carbon on either brush (B) is worn to 3/16" in length, or if either spring or
shunt wire (C) is burned or damaged in any way, replace both brushes. If the brushes are found serviceable after
removing, reinstall them in the same position.
C
A
B
Fig. 53
Fig. 54
20
Download from Www.Somanuals.com. All Manuals Search And Download.
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use
solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for
blown fuses or open circuit breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions.
No further lubrication is necessary.
SERVICE
REPLACEMENT PARTS
When servicing use only identical replacement parts.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including
brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or a
PORTER-CABLE•DELTA FACTORY SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective
material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information
shown on the nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta Supplier, Porter-Cable•Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your
nearest supplier.
Since accessories other than those offered by Porter-Cable•Delta have not been tested with this product, use of
such accessories could be hazardous. For safest operation, only Porter-Cable•Delta recommended accessories
should be used with this product.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts
of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof
of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made
by other than our Service Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR
ONE (1) YEAR FROM THE DATE OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, Jackson, Tennessee 38305; Attention:
Product Service. THE FOREGOING OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND UNDER NO
CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Machinery are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MICHIGAN
Tampa 33609
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
MINNESOTA
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Phone: (602) 437-1200
Fax: (602) 437-2200
GEORGIA
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Minneapolis 55429
CALIFORNIA
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Phone: (404) 608-0006
Fax: (404) 608-1123
MISSOURI
PENNSYLVANIA
Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
ILLINOIS
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
San Diego 92111
7638 Clairemnot Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
St. Louis 63119
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
NEW YORK
MARYLAND
COLORADO
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Houston 77043
4321 Sam Houston Parkway,
West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
MASSACHUSETTS
FLORIDA
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
WASHINGTON
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Phone: (954) 321-6635
Fax: (954) 321-6638
OHIO
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 767-4132
Fax: (519) 767-4131
Phone: (604) 420-0102
Fax: (604) 420-3522
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,
Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,
Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,
MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®,
PORTA-BAND®,
PORTA-PLANE®,
PORTER-CABLE®&(design), PORTER-
CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),
QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW
BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,
Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
PC - 0704 - 149
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Philips Automobile Accessories Ford Taurus 1996 1999 User Manual
Philips Camera Accessories R14B2A245 27 User Manual
Philips Car Stereo System SA4126 User Manual
Philips CRT Television TP2781C User Manual
Philips Flat Panel Television 150MT20P User Manual
Philips Indoor Furnishings TTX400 User Manual
Philips Universal Remote SRU8112 27 User Manual
Powermate Portable Generator PM054300017 User Manual
ProForm Home Gym PFEL39261 User Manual
PYLE Audio Power Supply PINV5 User Manual