14" Metal/Wood Cutting
Band Saw
Model 28-306
Shown with Optional Stand
and Optional Mobile Base
PART NO. 426-03-651-0011 - 06-03-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Download from Www.Somanuals.com. All Manuals Search And Download.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1.
2.
FOR YOUR OWN SAFETY, READ THE INSTRUCT-
13. USE RECOMMENDED ACCESSORIES. The use
of accessories and attachments not recommend-
ed by Delta may cause damage to the machine or
injury to the user.
TION MANUAL BEFORE OPERATING THE
MACHINE. Learning the machine’s application,
limitations, and specific hazards will greatly mini-
mize the possibility of accidents and injury.
USE CERTIFIED SAFETY EQUIPMENT. Eye pro-
tection equipment should comply with ANSI Z87.1
standards, hearing equipment should comply with
ANSI S3.19 standards, and dust mask protection
should comply with MSHA/NIOSH certified respi-
rator standards. Splinters, air-borne debris, and
dust can cause irritation, injury, and/or illness.
DRESS PROPERLY. Do not wear tie, gloves, or
loose clothing. Remove watch, rings, and other
jewelry. Roll up your sleeves. Clothing or jewelry
caught in moving parts can cause injury.
DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp
or wet locations or in rain can cause shock or elec-
trocution. Keep your work area well-lit to prevent
tripping or placing arms, hands, and fingers in
danger.
MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating
and changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.
CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions
that may affect its operation. A guard or any other
part that is damaged should be properly repaired
or replaced. Damaged parts can cause further
damage to the machine and/or injury.
KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
KEEP CHILDREN AND VISITORS AWAY. Your shop is
a potentially dangerous environment. Children and visitors
can be injured.
14. USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See the Extension Cord Chart for the correct size
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to
hold the workpiece when practical. Loss of control
of a workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION
OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE. Feeding it from the other
direction will cause the workpiece to be thrown out
a high speed.
3.
4.
5.
6.
17. DON’T FORCE THE WORKPIECE ON THE
MACHINE. Damage to the machine and/or injury
may result.
18. DON’T OVERREACH. Loss of balance can make
you fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if
the tool tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-
DED. TURN THE POWER OFF. Don’t leave the machine
until it comes to a complete stop. A child or visitor could
be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs. An
accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental
start-up of a machine by a child or visitor could
cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while oper-
ating power tools may result in injury.
7.
8.
9.
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of
a power failure, move the switch to the “OFF”
position. An accidental start-up can cause injury.
10. USE THE GUARDS. Check to see that all guards
are in place, secured, and working correctly to pre-
vent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high
speed, causing injury.
12. USE THE RIGHT MACHINE. Don’t force a
machine or an attachment to do a job for which it
was not designed. Damage to the machine and/or
injury may result.
24. THE DUST GENERATED by certain woods and
wood products can be injurious to your health.
Always operate machinery in well-ventilated areas,
and provide for proper dust removal. Use wood
dust collection systems whenever possible.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY RULES FOR
BAND SAWS
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
1. DO NOT OPERATE THIS MACHINE UNTIL it is
14. NEVER REACH UNDER THE TABLE while the
assembled and installed according to the instruc-
machine is running.
tions.
15. TURN THE MACHINE “OFF” to back out of an
2. OBTAIN ADVICE from your supervisor, instruc-
tor, or another qualified person if you are not
familiar with the operation of this tool.
uncompleted or jammed cut.
16. MAKE “RELIEF” CUTS prior to cutting long curves.
17. TURN THE MACHINE “OFF” and wait for the blade
to stop prior to cleaning the blade area, removing
debris near the blade, removing or securing work-
piece, or changing the angle of the table. A coasting
blade can be dangerous.
18. NEVER PERFORM LAYOUT, ASSEMBLY, or set-
up work on the table/work area when the machine is
running.
19. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs.
20. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK
THE SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
4. USE THE GUARDS WHENEVER POSSIBLE. Check
to see that they are in place, properly adjusted,
secured, and working correctly.
5. USE PROPER BLADE SIZE and type.
6. ADJUST THE UPPER BLADE GUIDE so that it is
about 1/8" above the workpiece.
7. PROPERLY ADJUST the blade tension, tracking,
blade guides, and blade support bearings.
8. KEEP ARMS, HANDS, AND FINGERS away from
the blade.
9. AVOID AWKWARD OPERATIONS and hand posi-
tions where a sudden slip could cause a hand to
move into the blade.
10. NEVER START THE MACHINE before clearing the
21. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
refer to the American National Standards Institute
ANSI 01.1 Safety Requirements for Woodworking
Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
table of all objects (tools, scrap pieces, etc.).
11. NEVER START THE MACHINE with the workpiece
against the blade.
12. HOLD WORKPIECE FIRMLY against the table. DO
NOT attempt to saw a workpiece that does not have
a flat surface against the table.
13. HOLD WORKPIECE FIRMLY and feed into blade at
a moderate speed.
SAVE THESE INSTRUCTIONS.
Refer to them often
and use them to instruct others.
04-24-03
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be pro-
tected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong ground-
ing type plugs and matching receptacle which will accept the machine’s plug. Before connecting the motor to the power line,
make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on
the machine. All line connections should make good contact. Running on low voltage will damage the motor.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Depending on the optional stand purchased, the tool is either wired for 120 volt, or 240 volt with 60 Hz. alternating current.
Before connecting the tool to the power source, make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
2. Grounded, cord-connected machines intended for
use on a supply circuit having a nominal rating less
than 150 volts:
In the event of a malfunction or breakdown, grounding pro-
vides a path of least resistance for electric current to reduce
the risk of electric shock. This machine is equipped with an
electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
If the machine is intended for use on a circuit that has an out-
let that looks like the one illustrated in Fig. A, the machine will
have a grounding plug that looks like the plug illustrated in Fig.
A. A temporary adapter, which looks like the adapter illustrat-
ed in Fig. B, may be used to connect this plug to a matching
2-conductor receptacle as shown in Fig. B if a properly
grounded outlet is not available. The temporary adapter should
be used only until a properly grounded outlet can be installed
by a qualified electrician. The green-colored rigid ear, lug, and
the like, extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box.
Whenever the adapter is used, it must be held in place with a
metal screw.
Do not modify the plug provided - if it will not fit the outlet, have
the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor
can result in risk of electric shock. The conductor with insu-
lation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor to
a live terminal.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the machine is properly grounded.
IN ALL CASES, MAKE CERTAIN THAT THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE, HAVE A
QUALIFIED ELECTRICIAN CHECK THE
RECEPTACLE.
Use only 3-wire extension cords that have 3-prong grounding
type plugs and matching 3-conductor receptacles that accept
the machine’s plug, as shown in Fig. A.
Repair or replace damaged or worn cord immediately.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING
MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
Fig. B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Grounded, cord-connected machines intended for
use on a supply circuit having a nominal rating
between 150 - 250 volts, inclusive:
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
If the machine is intended for use on a circuit that has an out-
let that looks like the one illustrated in Fig. C, the machine
will have a grounding plug that looks like the plug illustrated
in Fig. C. Make sure the machine is connected to an outlet
having the same configuration as the plug. No adapter is
available or should be used with this machine. If the machine
must be re-connected for use on a different type of electric
circuit, the re-connection should be made by qualified ser-
vice personnel; and after re-connection, the machine should
comply with all local codes and ordinances.
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. C
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord
which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When
using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized
cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge
to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the
heavier the cord.
MINIMUM GAUGE EXTENSION CORD
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Volts
Volts
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
0-6
0-6
0-6
0-6
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
6-10
6-10
6-10
6-10
240
240
240
240
up to 50
50-100
100-200
200-300
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
240
240
240
240
up to 50
50-100
100-200
200-300
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
12-16
12-16
12-16
240
240
240
up to 50
50-100
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. D
Fig. D
OPERATING INSTRUCTIONS
FOREWORD
Delta Model 28-306 is a 14" Metal and Wood Cutting Band Saw. This machine has speeds of 40, 60, 85, 115, 160, 220, 335,
and 3000 SFM. Its blade to frame capacity is 13-3/4" and its under-guide and wheel capacity is 6-1/4".
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpaint-
ed surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thin-
ner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.
THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER
ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABEL-
ING OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
NOTE:
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
7
CARTON CONTENTS
1. Band Saw with Pulleys attached
2. Large V-Belt
3. Small V-Belt
4. Motor Pulley
6
5
5. 3/4" to 5/8" Reducing Bushing
6. Belt and Pulley Guard Clamp
7. Key
8. Belt and Pulley Guard
1
2
3
8
ASSEMBLY
OPTIONAL STAND
The optional stand is shipped top-down in the shipping
container with the motor mounted to the inside top of the
stand. The on/off switch is wired to the end of the power
cord.
A
B
To make the motor operational, do the following:
D
C
1. Remove the stand (A) Fig. 4 from the shipping container.
Be careful not to crimp the switch cord that extends
through the top of the stand. NOTE: Set the stand on
several blocks of wood to raise the stand off the floor.
2. Take the panel (B) Fig. 4 off of the stand (A) by removing
two screws (C) and loosening the two other screws (D).
Remove the panel on the opposite side of the stand in
the same way.
Fig. 4
Fig. 5
Fig. 6
3. Remove the two mounting screws that are holding the
motor (F) Fig. 5 to the top of the stand. One screw is
shown at (E) Fig. 5.
G
J
H
DO NOT REMOVE THE CABLE TIE (G) that
holds the switch cord (H) to the vertical
mounting bar (J) unless the accessory height
attachment will be used on the tool. This
cable tie will prevent contact between the
switch cord and the motor pulley or belt.
IMPORTANT:
F
ATTACHING MOTOR TO OPTIONAL
STAND
1. Turn the stand on its side with the two bars (B) Fig. 6
down.
2. Position the motor (C) Fig. 6 on the two horizontal
support bars (B), and fasten with the four 5/16-18 x 2"
carriage bolts and flanged nuts, two of which are shown
at (D).
E
PLACE THE MOTOR SHAFT (E) on the
same side of the stand as the large open-
ing in the top of the stand (See (B) Fig. 7)
before loosely tightening the carriage bolts
(D). Further alignment will be necessary
after the saw is attached to the stand.
IMPORTANT:
3. Carefully turn the stand right side up.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING BAND SAW TO THE OPTIONAL STAND
The band saw is very heavy. Use a helper when attaching the saw to the stand.
Attach the band saw to the optional stand using the four holes provided (two are shown at (A) Fig. 7). Place one 5/16 -18 x 1-
3/4" hex head screw with one 5/16" flat washer through each hole through the bottom of the band saw and the top of the stand,
and attach with a 5/16" lock washer, and 5/16-18 hex nut.
NOTE: Screws, washers, and nuts for attaching the saw to the stand come with the optional stand.
C
B
B
A
A
D
A
A
B
E
Fig. 7
Fig. 8
Fig. 9
ATTACHING MOTOR PULLEY
Both the motor pulley (A) Fig. 8, and the gearbox pulley (B) are four-step pulleys and should always be attached inverted to
each other. Check to see if the gear box pulley (B) is attached with the largest step of the pulley in the “in” or “out” position. In
this case, the largest step of the gear box pulley (B) is in the “in” position. Attach the motor pulley (A) to the motor shaft with
the largest step of the motor pulley in the “out” position.
When attaching the motor pulley (A) to the motor shaft, use the supplied 3/4" to 5/8" reducing bushing on the motor
shaft. Place the supplied key in the motor shaft. Position the reducing bushing on the shaft, being sure to line the
split in the reducer with the key. Position the pulley on the shaft. Line it up with the key. Secure with the two supplied
5/16-18 x 5/16" set screws.
NOTE:
ATTACHING BELT AND PULLEY GUARD, ATTACHING AND ALIGNING V-BELT,
ADJUSTING BELT TENSION
DISCONNECT MACHINE FROM POWER SOURCE.
1. Use a straight edge to align the inside grooves of the pulleys (A) and (B) Fig. 9 to the inside edge of the drive pulley (C). The
pulleys can be moved in or out on the shafts and the motor can also be moved.
2. Place the belt and pulley guard (A) Fig. 10A over the belt opening and position the two clamps (B) over the guard flanges
and under the top of the stand. Use the four 1/4-20 x 1/2” round head screws in the holes in the bottom of the clamps to
fasten in place.
3. Attach the largest V-Belt to the inside groove of the motor pulley (A) Fig. 9 and to the drive pulley (C) Fig. 9. Attach the small-
er V-Belt to any one of the remaining three grooves of the motor pulley (A) and the corresponding groove of the gear box
pulley (A). (Fig. 10B shows belts in place. Belt and pulley guard was removed for clarity.)
4. Adjust the belt tension by raising or lowering the motor on the motor mounting bars (D) Fig. 9. If necessary, the motor
mounting can be repositioned on the two posts (E) Fig. 9. Keep the pulleys in alignment when performing this operation.
With light finger pressure, a 1" deflection in the belt at the center span of the pulleys indicates the proper tension.
A
B
Fig. 10A
Fig. 10B
8
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
Fig. 12
Fig. 11
ATTACHING THE SWITCH
A push-button switch (mounted in a switch box) and a cord set are supplied with the unit. To attach the switch to the band saw
arm:
DISCONNECT MACHINE FROM POWER SOURCE.
The on/off switch-to-motor cord (F) Fig. 11 is tied to the vertical mounting post (G) opposite the motor pulley. The
cable tie (H) prevents the switch-to-motor cord (F) from contacting the belt or motor pulley during operation.
IMPORTANT:
LEAVE THIS CABLE TIE IN PLACE. Remove it ONLY when using the Accessory Height Attachment with the
machine.
1. Remove the two outer hex nuts and lock washers (A) Fig. 12 from the two screws extending out from the back of the switch
box (B).
2. Insert two screws (C) Fig. 13, located on back of switch box, into two holes (D) located in the band saw arm.
3. Use the two nuts and lockwashers (E) Fig. 14, removed in STEP 1, to fasten the switch box to the bandsaw arm (Fig. 14).
4. Remove the screw and cable clamp (E) Fig. 15 from the lower arm of the band saw.
5. Insert the switch cord into the clamp (E) (removed in STEP 4), and fasten the switch cord to the machine.
Prevent contact between the on/off switch-to-motor cord (F) Fig. 16 and the motor pulley or belt. If necessary,
adjust the cord, then tighten the cable tie (H) Fig.11.
IMPORTANT:
6. Attach the two side panels removed earlier.
D
C
E
Fig. 13
Fig. 14
E
Fig. 15
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING SAW
K
K
L
M
Fig. 17
Fig. 18
To start the machine, press the “START” button (K) Fig. 17. To stop the tool, press the “STOP” button (L) Fig. 17.
When the machine is not in use, the switch should be locked in the “OFF” position to prevent
unauthorized use, using a padlock (M) Fig. 18 with a 3/16" diameter shackle
B
A
A
Fig. 20
Fig. 19
TABLE INSERT
Place the table insert (A) Fig. 19 in the hole provided in the table. Engage the protrusion on the insert in the indent (B) in the table.
TILTING THE TABLE
1. The table on the machine can be tilted 45 degrees to the right and 10 degrees to the left. To tilt the table to the right, loosen
the two locking knobs (A) Fig. 20, tilt the table to the desired angle, then re-tighten two locking knobs (A).
2. To tilt the table to the left, loosen the two locking knobs (A) Fig. 20, and tilt the table to the right until the table stop (A) Fig. 21
is accessible. Remove the table stop (A) Fig. 21, and tilt the table to the left. Tighten the two locking knobs (A) Fig. 20.
A
B
C
Fig. 21
Fig. 22
ADJUSTING THE TABLE STOP
The machine is equipped with an adjustable table stop (A) Fig. 21 that allows the table to be set at 90 degrees to the blade.
Tilt the table to the right until the table stop (A) Fig. 21 contacts the table. Place a square on the table against the blade (Fig. 22).
Check to see if the blade is 90 degrees to the table surface. If not, do the following:
1. Tilt the table slightly to the left and tighten the table lock knobs.
2. Loosen the locknut (B) Fig. 21 to free the adjustment nut (A) Fig. 21. Turn the adjustment nut (A) right or left to raise or lower
the table stop.
3. Lower the table. Check to see that the table is 90 degrees to the blade (Fig. 22). If it is, raise the table, hold the stop (A) Fig. 21
and tighten nut (B).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
A
A
B
D
C
Fig. 23
Fig. 24
Fig. 25
ADJUSTING BLADE TENSION
DISCONNECT MACHINE FROM POWER SOURCE.
A series of graduations is located on the back of the upper wheel slide bracket. These graduations indicate the proper tension
for various widths of blades. With the blade on the wheels, turn the knob (A) Fig. 23 to raise or lower the wheel, until the red
fiber washer (D) Fig. 25 is in line with the proper graduation for the size of the blade used.
These graduations are correct for average work, and will not be affected by rebrazing of the saw blade. Use these graduations
until you become familiar enough with the operation of the band saw to vary the tension for different kinds of blades or work.
IMPORTANT:
OVER-STRAINING is a common cause of blade breakage and other unsatisfactory blade performance.
Release the blade tension when the machine is not in use.
TRACKING THE BLADE
DISCONNECT MACHINE FROM POWER SOURCE.
IMPORTANT:
Before tracking the blade, be certain that the blade guides and blade support bearings do not touch the blade.
After applying tension to the blade, rotate the wheels slowly forward by hand and observe the blade’s movement. The blade
(A) Fig. 24 should travel just to the front of the center of the upper tire. If the blade creeps toward the front edge, loosen the
wing nut (B) Fig. 25, and tighten the thumb screw (C). This will draw the blade toward the center of the tire. If the blade creeps
toward the back edge, turn the thumb screw in the opposite direction. Adjust the thumb screw (C) Fig. 25 only a fraction of a
turn each time. NEVER TRACK THE BLADE WHILE THE MACHINE IS RUNNING. After the blade is tracking just to the front
of the center of both tires, tighten the wing nut (B) Fig. 25. Adjust the Blade Guides and Bearings.
VERTICAL ADJUSTMENT OF THE
UPPER BLADE GUIDE ASSEMBLY
DISCONNECT MACHINE FROM POWER SOURCE.
B
A
Set the upper blade guide assembly (A) Fig. 26 as close as possi-
ble to the top surface of the workpiece. Loosen the lock knob (B)
and move the guide assembly (A) to the desired position.
Fig. 26
ADJUSTING THE UPPER BLADE GUIDES AND BLADE SUPPORT BEARING
Adjust the upper blade guides and blade support bearings ONLY AFTER the blade has the correct tension and is tracking prop-
erly. To adjust:
DISCONNECT MACHINE FROM POWER SOURCE.
1. Make sure that the bottom blade guides and support bearings
do not touch the blade.
C
B
2. Check the upper blade guide assembly. The blade guides (A)
Fig. 27 should be parallel to the blade. To adjust, loosen the
A
screw (B) and rotate the complete guide assembly (C). When
the blade guides are parallel with the blade, tighten the screw
(B).
Fig. 27
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Adjust the guides (A) Fig. 28, so that the front edge of the guides
are just behind the “gullets” of the saw teeth. The complete guide
block bracket can be moved in or out by loosening the thumb
screw (C) Fig. 28 and turning the knurled knob (D) Fig. 28. When
the guides (A) are set properly, tighten thumb screw (C).
F
G
4. Two set screws (B) Fig. 28 hold the upper blade guides (A) in
place. Loosen the set screws (B) to move the guides (A). Place
them as close as possible to the side of the blade. (Be careful not
to pinch the blade). Tighten the screws (B).
H
E
C
D
5. When the blade guide wears to a point that it cannot be adjusted
close to the blade, loosen screw (B) Fig. 28 and reverse the blade
guides (A) Fig. 28.
B
B
A
A
6. The upper blade support bearing (E) Fig. 28 prevents damage to
the set in the saw teeth by keeping the blade from being pushed
Fig. 28
too far toward the back. The support bearing (E) should be set 1/64" behind the blade by loosening the thumb screw (F)
and turning the knurled knob (G) to move the support bearing (E) in or out.
7. Adjust the blade support bearing (E) so that the back edge of the blade overlaps the outside diameter of the ball bearing
by about 1/16". The bearing (E) is set on an eccentric. To change the position, remove the screw (H) and bearing (E) Fig.
28. Loosen the thumb screw (F), back out the knurled knob from the set screw. Remove the hex shaft from the hole, and
rotate it to move the eccentric for the bearing.
ADJUSTING LOWER BLADE GUIDES AND
B
E
B
BLADE SUPPORT BEARING
A
A
Adjust the lower blade guides and blade support bearing after the the
upper guides and bearing have been adjusted.
C
DISCONNECT MACHINE FROM POWER SOURCE.
1. Adjust the front edge of the guide blocks (B) so that they are just
behind the “gullets” of the saw teeth. Turn the knurled knob (C) Fig.
29 to make this adjustment. Check the support bearing. It should not
be touching the back of the blade.
D
2. Loosen the two screws (A) Fig. 29. Move the guides (B) as close
as possible to the side of the blade, being careful not to pinch the
blade. Tighten screws (A).
Fig. 29
3. Turn the other knurled knob (E) to adjust the lower blade support bearing (D) Fig. 29 so that it is about 1/64" behind the back
of the blade.
CHANGING SPEEDS
An advantage of this machine is that it can be changed instantly from a slow-speed metal cutting band saw to a standard high-
speed wood cutting band.
DISCONNECT MACHINE FROM POWER SOURCE.
Be certain that the band saw is in the “off” position and the power is disconnected when changing from either metal-to-wood
cutting or from wood-to-metal cutting.
Fig. 30
Fig. 31
When using the machine for wood cutting (3000 SFM), pull the shifter knob (A) Fig. 30 all the way out so that the lugs of the
clutch (B) are engaged with the hub (C) of the drive pulley. This action will disengage the clutch (D) from the hub (E) of the gear
that transmits power through the gear box. It may be necessary to rotate the pulley manually in order to line up the clutch lugs
with the slots in the hub of the pulley. This action provides a direct drive from the motor pulley to the drive pulley, by-passing
the gear box.
When using the machine for metal cutting (40, 60, 85, 115, 160, 220, and 335 SFM), push the shifter knob (A) Fig. 31 all the way
in, disengaging the clutch (B) from the hub (C) of the pulley. An additional clutch (D) is located inside the band saw. It must be
engaged with the hub (E) of the gear that transmits power through the gear box. When pushing in on the shifter knob (A) Fig.
31, rotate the lower wheel of the band saw to feel when the engagement occurs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BELT AND PULLEY ARRANGEMENTS FOR ALL EIGHT AVAILABLE SPEEDS
Fig. 32
Fig. 33
With the longest belt on the inside groove of the motor pulley (B) Fig. 32 and on the drive pulley (C), and the small belt in one
of the remaining three grooves of the motor pulley and the corresponding groove of the gear box pulley (E), speeds of 40, 60,
85, and 3000 SFM are readily available. To obtain speeds of 40, 60, and 85 SFM, push the shifter knob (F) Fig. 32 all the way
in, and position the small belt on one of the three outside grooves of the motor pulley (B) and the gear box pulley (E).
Blade speeds of 115,160, 220, 335, and 3000 SFM are available by simply interchanging the positions of the motor pulley and
the gear box pulley. Fig. 33 shows the motor pulley (A) positioned on the gear box shaft and the gear box pulley (B) positioned
on the motor shaft. With the long belt positioned on the inside groove of the pulley (B) and the pulley (C), and the small belt
positioned in one of the remaining three grooves of the pulleys (A) and (B) Fig. 33, speeds of 160, 220, and 335 SFM are
obtained when the shifter knob (D) is pushed in.
To obtain a blade speed of 115 SFM, push in the shifter knob (D), remove the long belt from the pulleys (B) and (C), and place
the small belt on the inside groove of the motor pulley (B) and the inside groove of the gear box pulley (A).
Except for the one speed of 115 SFM, both belts may be left on the machine, regardless of the blade speed.
TROUBLESHOOTING GUIDE
Even though a band saw is well-maintained, problems can occur. This troubleshooting guide can help you solve the
more common problems:
Trouble: SAW WILL NOT START.
Probable Cause
Remedy
1. Saw not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord damaged.
1. Plug in saw.
2. Replace fuse or reset circuit breaker.
3. Have cord replaced.
Trouble: SAW WILL RUN, BUT BLADE WILL NOT TURN
Probable Cause
1. Gearbox is disengaged.
1. Properly engage the shifter knob.
Trouble: BREAKER KICKS OUT FREQUENTLY.
Probable Cause
1. Extension cord too light or too long.
2. Feeding stock too fast.
3. Blade in poor condition (dull, warped, gummed).
4. Low voltage supply.
Remedy
1. Replace with adequate size cord.
2. Feed stock more slowly.
3. Clean or replace blade.
4. Contact an electrician.
Trouble: BAND SAW VIBRATES EXCESSIVELY.
Probable Cause
Remedy
1. Machine not mounted securely to stand.
2. Stand on uneven surface.
3. Worn belt.
1. Tighten all mounting hardware.
2. Reposition on flat level surface.
3. Replace belt.
4. Pulley not aligned.
5. Motor not fastened securely.
4. Adjust pulleys.
5. Tighten all mounting hardware.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble: BAND SAW DOES NOT COME UP TO SPEED.
Probable Cause
1. Low voltage due to improper extension cord size.
2. Low voltage.
Remedy
1. Replace with adequate size cord.
2. Contact an electrician.
Trouble: BLADES BREAK.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly adjusted.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Blade wheel tracking adjustment improperly set.
5. Bad weld on blade.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
7. Forcing wide blade around short radius.
8. Dull blade or insufficient set.
9. Upper blade guide set too high.
10. Continuous running of machine when not actually
cutting.
7. Change to a narrower blade.
8. Replace blade.
9. Set upper blade guide within 1/8" of workpiece.
10. Turn off machine when not performing cutting
operation.
Trouble: BLADE WILL NOT TRACK.
Probable Cause
1. Blade too loose
Remedy
1. Adjust tension
2. Upper wheel not properly adjusted.
3. Improperly adjusted blade support bearing.
2. Adjust upper wheel.
3. Adjust blade support bearing.
Trouble: CUT DOES NOT AGREE WITH SETTING ON THE TILT SCALE.
Probable Cause
1. Pointer out of adjustment
Remedy
1. Adjust pointer.
Trouble: BLADE WILL NOT STAY ON WHEEL.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly adjusted.
4. Blade wheel not tracking properly.
5. Bad weld on blade.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
Trouble: BAND SAW MAKES UNSATISFACTORY CUTS.
Probable Cause
Remedy
1. Blade not tensioned properly.
2. Blade guides improperly adjusted.
3. Blade support bearing improperly set.
4. Blade wheel not tracking properly.
5. Bad weld on blade.
1. Adjust blade tension.
2. Check and adjust blade guides.
3. Adjust blade support bearing.
4. Check and adjust blade tracking.
5. Replace the blade.
6. Worn tires.
6. Replace tires.
7. Incorrect blade for work being done.
8. Dull blade or insufficient set.
9. Upper blade guide set too high.
10. Adjustable speed set incorrectly.
7. Change the blade.
8. Replace blade.
9. Set upper blade guide within 1/8" of work piece.
10. Check and adjust speed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE BAND SAW
DISCONNECT MACHINE FROM POWER SOURCE.
Before starting the machine, make all adjustments and put all guards in place. Turn the upper wheel clockwise by hand to be
sure that everything is correct before providing power to the tool.
Keep the top guide close to the work. Do not force the material against the blade. Light contact with the blade will permit eas-
ier following of the line and will prevent excess friction, heating, and work-hardening of the blade at its back edge.
Keep the saw blade sharp and very little pressure will be required for average cutting.
Avoid twisting the blade by turning abrupt corners.
CUTTING CURVES
When cutting curves, turn the stock carefully so that the blade may follow without being twisted. If a curve is so abrupt that
repeated new kerfs are needed, then use either a narrower blade or one that has more set. The more set a blade has, the
easier the stock is to turn. However, the cut is usually rougher than when using a medium set.
When withdrawing the blade, be careful not to draw the blade off of the wheels. In most cases, it is easier and safer to turn the
workpiece and saw out through waste material. Do not back the blade out while the saw is running.
SUGGESTED METAL CUTTING BLADES AND SPEEDS
UNDER ¼”
1/ TO ¾”
1 “AND UP
TEETH
PER
INCH
24
18
24
24-18
24-18
14
FPM
TEETH
PER
INCH
14
14
14
14
14
14
FPM
TEETH
PER
INCH
FPM
MATERIAL
STEELS
Angle Iron
Armor Plate
Carbon Steel
Chromium Steel
Cold Rolled Steel
Drill Rod
160
40
60
60
220
160
40
85
85
220
85
10
14
14
14
40
40
40
160
60
Graphite Steel
Hidfh speed Steel
Machinery Steel
Molybenium Steel
Nickel Steel
Silicon Manganese
Stainless Steel
Structural Steel
Tungsten Steel
40
60
160
60
40
85
40
160
40
18
24
18
18
18
18
24
24
60
85
160
85
40
85
40
160
40
14
14
14
14
14
14
14
14
14
14
14
14
14
14
10
14
10
40
40
160
40
40
60
40
115
40
18
14
FOUNDRY METALS
Brass-hard and soft
Bronze – Aluminum
Bronze – Manganese
Bronze _ Naval
Bronze – Phosphorus
Cast Iron – Gray
Cast Iron – Malleable
Cast Steel
Copper – Beryllium
Gunnite
Meehanite
Monet
335
335
115
115
335
85
115
115
85
220
115
85
40
220
220
18
18
18
18
18
18
18
18
18
24
18
18
14
18
24
14
14
14
14
14
14
14
14
14
18
14
14
10
14
18
10
14
14
14
14
10
14
14
10
14
10
10
10
14
14
335
335
85
85
220
60
85
85
40
160
85
60
40
220
220
335
335
160
160
335
115
160
160
160
335
160
115
60
Nickel – Cold Rolled
Nickel Silver
Silver
220
220
NON-METALS
Bakelite
Cork
220
3000
3000
10
10
14
10
24
24
14
24
24
10
10
10
10
10
10
160
3000
3000
335
3000
3000
3000
220
335
3000
160
335
335
Fibre
Hose –Canvas, Rubber
Hose – Mettalic
Mica
Plastics
Porcelain
Slate
220
3000
115
220
220
18
14
18
18
18
14
10
220
3000
14
14
160
85
Transite
24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SKIP TOOTH BLADES AND SPEEDS
2”AND UP
UNDER ½”
1/2” TO 2”
MATERIAL
STEELS
TEETH
PER
FPM
TEETH
PER
FPM
TEETH
PER
FPM
INCH
INCH
INCH
Aluminum
Asbestos
Babbitt
Brake Lining
Carbon
Copper – Drawn
Duralumin
Lead
Magnesium
Paper Board
Rubber – Hard
Zinc
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3
4
3
4
3
4
3
4
3
4
4
4
4
4
4
4
4
3
4
3
3000
3000
3000
3
4
4
6
4
6
3
6
3
6
6
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3
4
3
4
3
4
4
4
4
4
4
4
4
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
3000
6
See note
Plastics
6
6
6
6
Builders Board
Hardwoods
Plywoods
Softwoods
3000
3000
3000
3000
NOTE:
Some types of plastics lend themselves to more pronounced results with the regular saw blades.
Sheets under ¼” thickness and tubing under ¼” wall thickness are not adapted to skip tooth blades.
WIDTH
MIN. CUTTING RADIUS
WIDTH
MIN. CUTTING RADIUS
1/8”
3/16”
1/4”
1/2”
3/8”
1/2”
1”
1-1/4”
1/4”
3/4”
3/4”
1-3/4”
BAND SAW BLADES
A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw
blade if you use it properly. Be sure you use blades of the proper thickness, width, and temper for the various types of material
and cuts.
Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves and for fine, delicate work. This
will save blades and will produce better cuts. For cutting wood and similar materials, Delta offers blades in widths of 1/8", 1/4",
3/8", and 1/2".
Any one of a number of conditions may cause a band saw blade to break. Blade breakage is, in some cases, unavoidable, being
the natural result of the peculiar stresses to which blades are subjected. Blades will break often due to avoidable causes, such
as the lack of care to the blade or the blade not being properly adjusted to the band saw. The most common causes of blade
breakage are:
(1) faulty alignments and adjustments of the guides.
(2) forcing or twisting a wide blade around a curve of short radius.
(3) feeding the work piece too fast into the blade.
(4) dullness of the teeth, or absence of sufficient set.
(5) improperly tensioned blade.
(6) top guide set too high above the work piece being cut.
(7) using a blade with a lumpy or improperly finished braze or weld.
(8) continuous running of the saw blade when not cutting.
Use blades that are 93½" in length on this machine.
Always use a sharp blade. Keep it free from gum and pitch. Clean frequently with a stiff fiber brush.
Narrow blades are used for cutting small circles or curves while the wider blades are best suited for straight cutting such as
ripping.
A new blade, in most cases, will perform better and last longer than a re-sharpened blade.
Ensure that the blade guides are adjusted properly.
Do not force or twist the blade around a curve or a very short radius.
Feed the workpiece through the blade at a consistent rate, allow the blade to do the cutting – do not feed the work piece too
fast.
Do not apply excessive tension to the blade. Set the tension only so that it drives the blade without slipping on the wheels.
Narrow blades require less tension than wider blades.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE BLADES
DISCONNECT MACHINE FROM POWER SOURCE.
1. Open the upper and lower wheel guards.
2. Release tension on the saw blade.
3. Loosen the table alignment pin with a wrench and pull out. Remove table insert.
4. Take the blade off the wheel, and guide it through the slot in the table.
5. Install the new blade by reversing the procedure. Table alignment pin should be re-seated by gently tapping it with a ham-
mer.
LUBRICATION
The gear case is filled at the factory with 1-1/2 quarts of
oil. The case should be drained after 1500 to 2000 hours
of operation and filled with a good grade of heavy adhe-
sive gear oil. A pipe plug is located underneath the
machine in line with the gear pulley. Remove this plug to
drain the oil.
A
This machine is equipped with a 1/2" street elbow (B)
Fig. 35 and a pipe plug (A).Remove the plug (A) to check
the oil level and, when necessary, to add oil.
The sealed-for-life ball bearings on the wheels of the
bandsaw and the blade supports require no lubrication.
B
NOTE:
Keep all oils away from blade supports.
Fig. 35
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this product,
use of such accessories could be hazardous. For safest operation, only Delta recommend-
ed accessories should be used with this product.
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the loca-
tion of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the prod-
uct prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor manufac-
turer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted defect
which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other
than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or con-
sequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s
exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability,
fitness for purpose, or otherwise, are expressly disclaimed by Delta.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Machinery are Available at These Locations
•
Delta)
Cleveland 44125
ARIZONA
MINNESOTA
ILLINOIS
Minneapolis 55429
8001 Sweet Valley Drive
Unit #19
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Phone: (216) 447-9030
Fax: (216) 447-3097
Phone: (602) 437-1200
Fax: (602) 437-2200
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
St. Louis 63119
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
COLORADO
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
Houston 77055
Phone: (954) 321-6635
Fax: (954) 321-6638
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
OHIO
WASHINGTON
MICHIGAN
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Fax: (248) 597-5004
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 836-2840
Fax: (519) 767-4131
Phone: (604) 420-0102
Fax: (604) 420-3522
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE·
DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®, BAM-
MER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™,
DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®,
‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-
BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design),
QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding
Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The
American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S
CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other coun-
tries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y tam-
bién pueden estar registradas en otros países.
20
Printed in U.S.A.
PC-0403-149
Download from Www.Somanuals.com. All Manuals Search And Download.
|