Planet Technology Switch FGSW 1820CS User Manual

User's Manual

FGSW-1820CS

FGSW-2620CS

16/24-Port 10/100Mbps with

2 Gigabit TP / SFP Combo

Web Smart Switch

- 1 -

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

1. INTRODUCTION ......................................................................................................................................................4

1.1 C HECKLIST ................................................................................................................................................................4

1.2 A BOUT THE S WITCH ..................................................................................................................................................4

1.3 F EATURES .................................................................................................................................................................5

1.4 S PECIFICATION ..........................................................................................................................................................6

2. HARDWARE DESCRIPTION..................................................................................................................................8

2.1 F RONT P ANEL ...........................................................................................................................................................8

2.2 R EAR P ANEL .............................................................................................................................................................9

2.3 H ARDWARE I NSTALLATION .......................................................................................................................................9

3. SWITCH MANAGEMENT.....................................................................................................................................1 3

3.1 O VERVIEW ..............................................................................................................................................................1 3

3.2 M ANAGEMENT M ETHO D .........................................................................................................................................1 3

3.2.1 Web Management ...........................................................................................................................................1 3

3.2.2 PLANET Smart Discovery Utility ...................................................................................................................1 3

3.3 L OGGING ON TO THE FGSW-1820CS / FGSW-2620CS .........................................................................................1 5

4. WEB MANAGEMEN T .............................................................................................................................................1 6

4.1 L OGIN IN TO THE S WITCH ........................................................................................................................................1 6

4.2 S YSTEM ...................................................................................................................................................................1 8

4.2.1 System Information .........................................................................................................................................1 9

4.2.2 IP Configuratio n .............................................................................................................................................2 0

4.2.3 Password Setting.............................................................................................................................................2 1

4.2.4 Factory Default...............................................................................................................................................2 2

4.2.5 Firmware Update............................................................................................................................................2 3

4.2.6 Reboo t .............................................................................................................................................................2 6

4.3 P ORT M ANAGEMENT ...............................................................................................................................................2 7

4.3.1 Port Configuration..........................................................................................................................................2 8

4.3.2 Port Mirroring ................................................................................................................................................3 0

4.3.3 Bandwidth Control..........................................................................................................................................3 1

4.3.4 Broadcast Storm Contro l ................................................................................................................................3 2

4.3.5 Port Statistic s ..................................................................................................................................................3 3

4.4 VLAN S ETTING ......................................................................................................................................................3 4

4.4.1 Port Based VLAN............................................................................................................................................3 7

4.4.2 Port Based VLAN Setting example: ................................................................................................................3 8

4.4.3 802.1Q VLAN..................................................................................................................................................3 9

4.4.4 802.1Q VLAN Setting example .......................................................................................................................4 2

4.4.5 MTU VLAN .....................................................................................................................................................4 8

4.5 T RUNK ....................................................................................................................................................................4 9

4.6 Q O S S ETTING ..........................................................................................................................................................5 1

4.6.1 Priority Mode..................................................................................................................................................5 2

4.6.2 Class of Service Configuration .......................................................................................................................5 3

4.6.3 TCP / UDP Port Based QoS ...........................................................................................................................5 5

4.7 S ECURITY F ILTER ....................................................................................................................................................5 7

4.7.1 MAC Address Filter ........................................................................................................................................5 8

4.7.2 TCP / UDP Filter............................................................................................................................................5 9

4.8 M ISC O PERATION ....................................................................................................................................................6 1

4.9 L OGOUT ..................................................................................................................................................................6 2

5. SWITCH OPERATION............................................................................................................................................6 3

5.1 A DDRESS T ABLE .....................................................................................................................................................6 3

5.2 L EARNIN G ...............................................................................................................................................................6 3

5.3 F ORWARDING & F ILTERING ....................................................................................................................................6 3

5.4 S TORE -AND -F ORWARD ...........................................................................................................................................6 3

5.5 A UTO -N EGOTIATION ...............................................................................................................................................6 3

6. TROUBLESHOOTING ............................................................................................................................................6 4

APPENDIX A NETWORKING CONNECTION.......................................................................................................6 5

A.1 S WITCH ‘S RJ-45 P IN A SSIGNMENT S .......................................................................................................................6 5

A.2 RJ-45 CABLE PIN ASSIGNMEN T ...............................................................................................................................6 5

- 3 -

Download from Www.Somanuals.com. All Manuals Search And Download.

1. INTRODUCTION

1.1 Checklist

Check the contents of your package for following parts:

FGSW-1820CS or FGSW-2620CS x1

Quick Installation Guide x1

User's manual CD x1

Power cord x 1

Rubber feet x 4

Two rack-mounting brackets with attachment screws x1

If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton

including the original packing material, and use them against to repack the product in case there is a need to return it to

us for repair.

In the following section, the term “Web Smart Switch” means the two Switch devices, ie. FGSW-1820CS and

FGSW-2620CS; term of “switch” can be any third switches.

1.2 About the Switch

The FGSW-1820CS / FGSW-2620CS provide 16/24 10/100Mbps Fast Ethernet ports and two Gigabit Ethernet ports,

either TP or SFP per port. The two Gigabit ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX

through SFP (Small Factor Pluggable) interfaces. The distance can be extended from 100 meters (TP), 550 meters

(Multi-mode fiber), up to above 10/20/30/40/50/70/120 kilometers (Single-mode fiber).

The FGSW-1820CS / FGSW-2620CS, equipped with non-blocking 7.2 / 8.8Gbps backplane, greatly simplifies the tasks of

upgrading your LAN for catering to increase bandwidth demands.

For efficient management, the FGSW-1820CS / FGSW-2620CS 16/24-Port 10/100Mbps + 2 Gigabit TP / SFP Combo

Web Smart Switch is equipped with remote Web interface. The FGSW-1820CS / FGSW-2620CS can be programmed for

- 4 -

Download from Www.Somanuals.com. All Manuals Search And Download.

advanced switch management functions such as port configuration, port-based / IEEE 802.1Q / MTU VLAN, port mirroring,

port trunk, QoS, bandwidth control, broadcast storm control, MAC address / TCP & UDP filter and IGMP Snooping v1/v2.

The FGSW-1820CS / FGSW-2620CS provide port-based / IEEE 802.1Q / MTU VLAN (port based / IEEE 802.1Q VLAN

including overlapping). The VLAN groups allowed on the FGSW-1820CS / FGSW-2620CS, will be maximally up to 18/26

for port-based / 32 for IEEE 802.1Q VLAN groups. Also the MTU VLAN divide port 1 to port 16/24 as separate LAN group

and only can access the public port 17,18 or port 18 / port 25,26 or port 26. Via supporting port trunking, the

FGSW-1820CS / FGSW-2620CS allow the operation of a high-speed trunk combining multiple ports. The FGSW-1820CS

/ FGSW-2620CS also provide two groups of up to 4-ports for trunking, and it supports fail-over as well.

With its Auto-Negotiation capability, all the RJ-45/STP ports of Web Smart Switch can be configured to speeds of

10/20Mbps / 100/200Mbps (Fast Ethernet) and 1000/2000Mbps (Gigabit Ethernet) automatically. In addition, the prod-

ucts are equipped with the MDI/MDI-X auto detection for easily plug and play connection, regardless of cabling

types-straight through or crossover.

1.3 Features

◆

Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard

16/24-Port 10/100Mbps Fast Ethernet Switch

2 10/100/1000Mbps ports share with 2 SFP interfaces

Each Switching ports support auto-negotiation-10/20, 100/200Mbps (Fast Ethernet) , 1000/2000Mbps (Gigabit

Ethernet) supported

◆

Auto-MDI/MDI-X detection on each RJ-45 port

Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x PAUSE frame flow control (full-duplex)

High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous

packets to optimize the network bandwidth

◆

4K MAC address table, automatic source address learning and ageing

2.75Mb embedded memory for packet buffers

Remote Web interface for Switch management and setup

Broadcast Storm Control support

Supports up to 18/26 port-based VLAN groups / 32 IEEE 802.1Q VLAN groups / MTU VLAN

Supports up to 2 Trunk groups, each trunk for up to maximum 4 port with 800Mbps bandwidth

Supports QoS , bandwidth control and MAC address filter / TCP & UDP filter on each port

Supports port mirroring function and IGMP Snooping v1 / v2

Firmware upgrade through Web interface

Password setting, IP setting and device description setting through Planet Smart discovery utility

19-inch rack mount size

Internal full-range power supply suitable for worldwide use

EMI standards complies with FCC, CE class A

- 5 -

Download from Www.Somanuals.com. All Manuals Search And Download.

1.4 Specification

Model

FGSW-1820CS

FGSW-2620CS

Hardware Specification

24 10/ 100Base-TX RJ-45

Auto-MDI/MDI-X ports

16 10/ 100Base-TX RJ-45

Auto-MDI/MDI-X ports

Ports

Gigabit ports

2 10/100/1000Mbps ports share with 2 SFP interfaces

Store-and-Forward

Switch Processing Scheme

Throughput (packet per second) 5.35Mpps.

6.54Mpps

8.8Gbps

Switch Fabric

Address Table

7.2Gbps.

4K entries

Share Data Buffer

2.75Mb embedded memory for packet buffers

Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex

440 x 120 x 44 mm (1U height)

Flow Control

Dimensions

Weight

1.56 kg

1.64 kg

Power Requirement

100~240V AC, 50-60 Hz, 0.5A

Power Consumption / Dissipa-

tion

16 watts / 54BTU

19 watts / 64BTU

Operating: 0~50 degree C

Storage: -40~70 degree

Temperature

Humidity Operating:

Smart function

5% to 90%, Storage: 5% to 90% (Non-condensing)

System Configuration

Web interface

Port speed duplex mode selection. Flow control disable / enable. Port dis-

able / enable. Port description on each port

Port configuration

Bandwidth Control

Yes, 1 / 2 / 4 / 8 / 16 / 32 / 64Mbps

Yes, 5% / 10% / 25% / 50% / Disable

Broadcast Storm Control

Port Statistics

VLAN

Display each port’s detail Ethernet traffic counter information

18/26 port-based VLAN groups / 32 IEEE 802.1Q VLAN groups / MTU VLAN

Support 2 groups of 4-Port trunk support, up to 800Mbps bandwidth per

trunk

Port trunking

Port Mirroring

Port mirroring allows monitoring of the traffic across any port in real time

Allow to assign low / high priority on each port.

QoS

First-In-First-Out, All-High-before-Low, Weight-Round-Robin QoS policy.

MAC address / TCP & UDP filter Yes

- 6 -

Download from Www.Somanuals.com. All Manuals Search And Download.

IGMP Snooping v1 / v2

Standards Conformance

Regulation Compliance

Allow to disable or enable.

FCC Part 15 Class A, CE

IEEE 802.3 (Ethernet)

IEEE 802.3u (Fast Ethernet)

IEEE 802.3ab(Gigabit Ethernet)

IEEE 802.3z(Gigabit Ethernet)

IEEE 802.3x (Full-duplex flow control)

IEEE 802.1Q VLAN

Standards Compliance

IEEE 802.1p QoS

- 7 -

Download from Www.Somanuals.com. All Manuals Search And Download.

2. HARDWARE DESCRIPTION

This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Web Smart Switch

and automatically distinguishes the speed of incoming connection.

This section describes the hardware features of Web Smart Switch. For easier management and control of the Web Smart

Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED

indicators. Before connecting any network device to the Web Smart Switch, read this chapter carefully.

2.1 Front Panel

The Front Panel of the Web Smart Ethernet Switch consists of 16/24x Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports,

Also provides 2 Gigabit TP/SFP combo ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through

SFP (Small Factor Pluggable) interface.

The LED Indicators are also located on the front panel of the Web Smart Switch.

Figure 2-1: FGSW-1820CS Switch front panel

Figure 2-2: FGSW-2620CS Switch front panel

2.1.1 LED indicators

System

LED

Color

Function

PWR

Green

Lights to indicate that the Switch has power.

Per 10/100Mbps port

LED

Color

Function

Lights to indicate the link through that port is established at 10/100Mbps full duplex mode.

Blink slowly to indicate the link through that port is established at 10/100Mbps half duplex mode.

Blink fast to indicate that the switch is actively sending or receiving data over that port.

Steady Lights to indicate the port is run at 100Mbps.

LNK/ACT Green

10/100

Orange

Blink Slowly to indicate the port is run at 10Mbps.

Per 10/100/1000Base-T port / SFP interfaces

LED

Color

Function

Lights to indicate the link through that port is established at 10/100/1000Mbps full duplex mode.

Blink slowly to indicate the link through that port is established at 10/100Mbps half duplex mode.

Blink fast to indicate that the switch is actively sending or receiving data over that port.

Steady Lights to indicate the port is run at 1000Mbps.

LNK/ACT

Green

100/1000

Green

Blink Slowly to indicate the port is run at 100Mbps

Off: indicate that the port is operating at 10Mbps.

- 8 -

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Press the RESET button once. The Web Smart Switch will reboot automatically.

#Notice:

2. Press the RESET button for 5 seconds. The Web Smart Switch will back to the factory default

mode; the entire configuration will be erased.

2.2 Rear Panel

The rear panel of the Web Smart Switch indicates an AC inlet power socket, which accepts input power from 100 to

240VAC, 50-60Hz, 0.5A.

Figure 2-3: FGSW-1820C / FGSW-2620CS Switch rear panel

Power Notice:

1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the

time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data

loss or network downtime.

2. In some area, installing a surge suppression device may also help to protect your Web Smart Switch from being

damaged by unregulated surge or current to the Web Smart Switch.

2.3 Hardware Installation

This part describes how to install your Web Smart Switch and make connections to the Switch. Please read the following

topics and perform the procedures in the order being presented. To install your Web Smart Switch on a desktop or shelf,

simply completed the following steps.

2.3.1 Desktop Installation

To install Web Smart Switch on a desktop or shelf, simply completed the following steps:

Step 1: Attached the rubber feet to the recessed areas on the bottom of the Web Smart Switch.

Step 2: Place the Web Smart Switch on a desktop or shelf near an AC power source.

Step 3: Keep enough ventilation space between the Web Smart Switch and the surrounding objects.

When choosing a location, please keep in mind the environmental restrictions discussed in

Chapter 1, Section 4, Specification.

#Notice:

Step 4: Connect your Switch to network devices.

A. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the front of the Web Smart Switch.

Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.

Connection to the Web Smart Switch requires UTP Category 5 network cabling with RJ-45 tips.

For more information, please see the Cabling Specification in Appendix A.

#^Notice:

Step 5: Supply power to the Web Smart Switch.

Connect one end of the power cable to the Web Smart Switch.

Connect the power plug of the power cable to a standard wall outlet then power on the Web Smart Switch.

When the Web Smart Switch receives power, the Power LED should remain solid Green.

- 9 -

Download from Www.Somanuals.com. All Manuals Search And Download.

2.3.2 Rack Mounting

To install the Web Smart Switch in a 19-inch standard rack, follow the instructions described below.

Step 1: Place your Web Smart Switch on a hard flat surface, with the front panel positioned towards your front side.

Step 2: Attach a rack-mount bracket to each side of the Web Smart Switch with supplied screws attached to the package.

Figure 2-4 shows how to attach brackets to one side of the Web Smart Switch.

Figure 2-4 Attaching the brackets to the Web Smart Switch

You must use the screws supplied with the mounting brackets. Damage caused to the parts by

using incorrect screws would invalidate your warranty.

Caution:

Step 3: Secure the brackets tightly.

Step 4: Follow the same steps to attach the second bracket to the opposite side.

Step 5: After the brackets are attached to the Web Smart Switch, use suitable screws to securely attach the brackets to the

rack, as shown in Figure 2-5.

Figure 2-5 Mounting the Web Smart Switch in a Rack

Step 6: Precede with the steps 4 and steps 5 of section 2.3.1 Desktop Installation to connect the network cabling and

supply power to your Web Smart Switch.

2.3.3 Installing the SFP transceiver

The sections describe how to insert an SFP transceiver into an SFP slot.

The SFP transceivers are hot-pluggable and hot-swappable. You can plug-in and out the transceiver to/from any SFP port

without having to power down the Web Smart Switch. As the Figure 2-6 appears.

- 10 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 2-6 Plug-in the SFP transceiver

Approved PLANET SFP Transceivers

PLANET Web Smart Switch supports both single mode and multi mode SFP transceiver. The following list of approved

PLANET SFP transceivers is correct at the time of publication:

■MGB-SX SFP (1000Base-SX SFP transceiver )

■MGB-LX SFP (1000Base-LX SFP transceiver )

It recommends using PLANET SFP transceiver on the Web Smart Switch. If you insert a SFP

#Notice:

transceiver that is not supported, the Web Smart Switch will not recognize it.

Before connect the other switches, workstation or Media Converter.

1. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX to

1000Base-SX, 1000Base-LX to 1000Base-LX.

2. Check the fiber-optic cable type match the SFP transceiver model.

To connect to 1000Base-SX SFP transceiver, use the multi-mode fiber cable- with one side must be male

duplex LC connector type.

To connect to 1000Base-LX SFP transceiver, use the single-mode fiber cable-with one side must be male

duplex LC connector type.

Connect the fiber cable

1. Attach the duplex LC connector on the network cable into the SFP transceiver.

2. Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media

Converter..

3. Check the LNK/ACT LED of the SFP slot on the front of the Web Smart Switch. Ensure that the SFP transceiver is

operating correctly.

4. Check the Link mode of the SFP port if the link failed. Co works with some fiber-NICs or Media Converters, set the Link

mode to “1000 Force” is needed.

Remove the transceiver module

1. Make sure there is no network activity by consult or check with the network administrator. Or through the management

interface of the switch/converter (if available) to disable the port in advance.

2. Remove the Fiber Optic Cable gently.

3. Turn the handle of the MGB module to horizontal.

4. Pull out the module gently through the handle.

- 11 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 2-7 Pull out the SFP transceiver

Never pull out the module without pull the handle or the push bolts on the module. Direct pull

out the module with violent could damage the module and SFP module slot of the Web Smart

Switch.

#Notice:

- 12 -

Download from Www.Somanuals.com. All Manuals Search And Download.

3. SWITCH MANAGEMENT

This chapter describes how to manage the Web Smart Switch. Topics include:

- Overview

- Management method

- Logging on to the Web Smart Switch

3.1 Overview

The Web Smart Switch provides a user-friendly, Web interface. Using this interface, you can perform various switch con-

figuration and management activities, including:

Please refer to the following Chapter 4 for the details.

3.2 Management Method

User can manage the Web Smart Switch by Web Management via a network connection.

3.2.1 Web Management

The PLANET FGSW-1820CS / FGSW-2620CS provide a built-in browser interface. You can manage the Switch remotely

by having a remote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.

The following shows how to startup the Web Management of the Switch, please note the Switch is configured through an

Ethernet connection, make sure the manager PC must be set on the same IP subnet address, for example, the default IP

address of the Switch is 192.168.0.100 (the factory-default IP address), then the manager PC should be set at 192.168.0.x

(where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

Use Internet Explorer 5.0 or above Web browser, enter default IP address http://192.168.0.100

After entering the username and password (default user name and password is “admin”) in login screen

3.2.2 PLANET Smart Discovery Utility

For easily list the FGSW-1820CS / FGSW-2620CS in your Ethernet environment, the Planet Smart Discovery Utility from

user’s manual CD-ROM is an ideal solution.

The following install instructions guiding you for run the Planet Smart Discovery Utility.

1. Deposit the Planet Smart Discovery Utility in administrator PC.

2. Run this utility and the following screen appears.

- 13 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 3-1 Planet Smart Discovery Utility Screen

If there are two LAN cards or above in the same administrator PC, choose different LAN card by

#^Notice:

use the “Select Adapter” tool.

3. Press “Refresh” button for list current connected devices in the discovery list, the screen is shown as follow.

Figure 3-2 Planet Smart Discovery Utility Screen

3. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version,

Device IP Subnet address, also can assign new password, IP Subnet address and description for the devices.

4. After setup completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning of

the 3 buttons above are shown as below:

Update Device: use current setting on one single device.

Update Multi: use current setting on choose multi-devices.

Update All: use current setting on whole devices in the list.

The same functions mentioned above also can be finding in “Option” tools bar.

- 14 -

Download from Www.Somanuals.com. All Manuals Search And Download.

5. To click the “Control Packet Force Broadcast” function, it can allow assign new setting value to the Web Smart Switch

under different IP subnet address.

6. Press “Connect to Device” button then the Web login screen appears in Figure 3-3.

7. Press “Exit” button to shutdown the planet Smart Discovery Utility.

3.3 Logging on to the FGSW-1820CS / FGSW-2620CS

When you log on to the Web Smart Switch Web interface for the first time, a sign-on string appears and you are prompted

for a Web login username and password.

Figure 3-3 Web Smart Switch Web Login Screen

The factory default login username and password is admin.

1. For FGSW-1820CS the display will be the same to FGSW-2620CS.

#^Notice:

2. For security reason, please change and memorize the new password after this first setup.

- 15 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4. WEB MANAGEMENT

To modify your PC’s IP domain to the same with Web Smart Switch then use the default IP address (192.168.0.100) to

remote configure Web Smart Switch through the Web interface.

The following section will base on the console screens of FGSW-2620CS, for FGSW-1820CS the

#^Notice:

display will be the same to FGSW-2620CS.

4.1 Login in to the Switch

To access the Web-browser interface you must first enter the user name and password, the default user name and

password is "admin”. You will see the following screen comes out on the Web browser program:

Figure 4-1 Web Login Screen

After the User name and Password is entered, you will see the Web Main Menu screen.

- 16 -

Download from Www.Somanuals.com. All Manuals Search And Download.

The Switch Menu provide seven major management functions, the screen in Figure 4-2 appears.

Figure 4-2 Web Main Menu Screen

The seven items and it description shown as below:

◆ System: Provide System configuration of Web Smart Switch. Explained in section 4.2.

◆ Port Management: Provide Port Management configuration of Web Smart Switch. Explained in section 4.3.

◆ VLAN Setting: Provide VLAN Setting configuration of Web Smart Switch. Explained in section 4.4.

◆ Trunk Setting: Provide Trunk Setting configuration of Web Smart Switch. Explained in section 4.5.

◆ QoS Setting: Provide QoS Setting configuration of Web Smart Switch. Explained in section 4.6.

◆ Security: Provide Security configuration of Web Smart Switch. Explained in section 4.7.

◆ Misc Operation: Provide Misc Operation configuration of Web Smart Switch. Explained in section 4.8.

◆ Logout: Provide Logout function of Web Smart Switch. Explained in section 4.9.

- 17 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2 System

This section provides System Information, IP Configuration, Password Setting, Factory Default, Firmware Update and

Reboot functions of Web Smart Switch, the screen in Figure 4-3 appears and Table 4-1 describes the System object of

Web Smart Switch.

Figure 4-3 System Web Page Screen

Object

Description

System Information

Display the MAC address, Hardware Version, and Software Version, Device Description. Ex-

plained in section 4.2.1.

IP Configuration

Password Setting

Factory Default

Firmware Update

Reboot

Allow to change the IP subnet address of Web Smart Switch. Explained in section 4.2.2.

Allow to change the username and password of Web Smart Switch. Explained in section 4.2.3.

Allow reset the Web Smart Switch to factory default mode. Explained in section 4.2.4.

Allow proceed firmware upgrade process of Web Smart Switch. Explained in section 4.2.5.

Allow reboot the Web Smart Switch. Explained in section 4.2.6.

Table 4-1 Descriptions of the System Web Page Screen Objects

- 18 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.1 System Information

This section displays the MAC address, Hardware Version and Software Version, also allow define the device description

and press “Apply” button to take affect. The screen in Figure 4-4 appears.

Figure 4-4 System Information Web Page Screen

Up to 16 characters is allowed for the Device Description.

#^Notice:

- 19 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.2 IP Configuration

This section provides change the IP Address, Subnet Mask and Gateway, the screen in Figure 4-5 appears.

Figure 4-5 IP Configuration Web Page Screen

.After setup complete and press “Apply” button to take affect. The following screen in Figure 4-6 appears and then another

Web page login screen with new IP address will show up. After input correct username and password then can continue the

Web Smart Switch management.

Figure 4-6 IP Configuration Web Page Screen

- 20 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.3 Password Setting

This section provides change the Username and Password, the screen in Figure 4-7 appears.

Figure 4-7 Password Setting Web Page Screen

Up to 8 characters is allowed for the username and password assign.

#Notice:

- 21 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.4 Factory Default

This section provides reset the Web Smart Switch to factory default mode, the screen in Figure 4-8 appears.

Figure 4-8 Factory Default Web Page Screen

Press “Factory Default” button to take affect. The following screen in Figure 4-9 appears and then another Web page

login screen with default setting will show up. After input default username and password then can continue the Web Smart

Switch management.

Figure 4-9 Factory Default Web Page Screen

- 22 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.5 Firmware Update

This section provides firmware upgrade of the Web Smart Switch, the screen in Figure 4-10 appears.

Figure 4-10 Firmware Update Web Page Screen

Press “Update” button for start the firmware upgrade process, the screen in Figure 4-11 & 4-12 appears.

Figure 4-11 Firmware Update Web Page Screen

- 23 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4-12 Firmware Update Web page Screen

Then the following screen appears, press “Browser” button to find the firmware location administrator PC, the screen in

Figure 4-13 appears.

Figure 4-13 Firmware Update Web Page Screen

- 24 -

Download from Www.Somanuals.com. All Manuals Search And Download.

After find the firmware location from administrator PC, press “Update” button to start the firmware upgrade process. The

screen in Figure 4-14 appears.

Figure 4-14 Firmware Update Web Page Screen

When firmware upgrade process is completed then the following screen appears, please wait for a while for system

reboot. After device reboot then can use the latest firmware of the Web Smart Switch.

Figure 4-15 Firmware Update Web Page Screen

Recommend to use IE 6.0 or FireFox browser tools for firmware upgrade process.

#Notice:

- 25 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2.6 Reboot

This section allows reboot the Web Smart Switch, the screen in Figure 4-16 appears.

Figure 4-16 Reboot Web Page Screen

Press “Reboot” button to reboot the Web Smart Switch, the screen in Figure 4-17 appears. After device reboot completed,

the Web login screen appears and login for further management.

Figure 4-17 Reboot Web Page Screen

- 26 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3 Port Management

This section provides Port Configuration, Port Mirroring, Bandwidth Control, Broadcast Storm Control and Port Statistics

from Web Smart Switch, the screen in Figure 4-18 appears and Table 4-2 describes the system object of Web Smart

Switch.

Figure 4-18 Port Management Web Page Screen

Object

Description

Port Configuration

Port Mirroring

Allow to configure each port of Web Smart Switch. Explained in section 4.3.1.

Allow to use port mirroring function of Web Smart Switch. Explained in section 4.3.2.

Bandwidth Control

Allow to configure bandwidth control of each port from Web Smart Switch. Explained in

section 4.3.3.

Broadcast Storm Control

Port Statistics

Allow to configure broadcast storm control of each port from Web Smart Switch. Explained

in section 4.3.4.

Display each port statistics of Web Smart Switch. Explained in section 4.3.5.

Table 4-2 Descriptions of the Port Management Web Page Screen Objects

- 27 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.1 Port Configuration

This section introduces detail settings of per port on Web Smart Switch; the screen in Figure 4-19 & 4-20 appears and

Table 4-3 & 4-4 descriptions the Port Configuration objects of Web Smart Switch.

Figure 4-19 Port Configuration Web Page Screen

Figure 4-20 Port Configuration Web Page Screen

- 28 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Object

Description

Port

Allow choosing all or one port of Web Smart Switch for further management, the available

options is All & 01 to 26 (FGSW-2620CS). Or All & 01 to 18 (FGSW-1820CS).

Speed Mode

Allow choosing various speed duplex mode from one specific port of Web Smart Switch,

the available options are shown as below:

Auto Negotiation

1000Full(1000Mbps Port Only)

100Full

100Half

10Full

10Half

Default mode is Auto Negotiation.

Flow Control

State

Allow to configure Flow control function of each port from Web Smart Switch, the available

options are Enable and Disable. Default mode is Enable.

Allow disable or enable one specific port from Web Smart Switch, the available options are

Enable and Disable. Default mode is Enable.

Port Description

Apply button

Allow input per Port Description of Web Smart Switch, up to maximum 8 characters allow.

Press “Apply” button for save current configuration of each port on Web Smart Switch.

Table 4-3 Descriptions of the Port Configuration Web Page Screen Objects

Object

Port

Description

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Display per port Current Status, such as Link, Speed Mode and Flow Control.

Display current link status from each port of the Web Smart Switch.

Display current speed mode from each port of the Web Smart Switch.

Display current flow control status from each port of the Web Smart Switch.

Current Status

Link

Speed Mode

Flow Control

Setting Status

Display per port Current Setting Status, such as Speed Mode, Flow Control, State and Port

Description.

Speed Mode

Flow Control

State

Display per port Speed Mode setting value.

Display per port Flow Control setting value.

Display per port State setting value.

Display per Port Description.

Port Description

Refresh button

Press “Refresh” button to refresh current status.

Table 4-4 Descriptions of the Port Configuration Web Page Screen Objects

- 29 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.2 Port Mirroring

This section introduces detail settings of Port Mirroring function of Web Smart Switch; the screen in Figure 4-21 appears

and Table 4-5 descriptions the Port Mirroring objects of Web Smart Switch.

Figure 4-21 Port Mirroring Web Page Screen

Object

Description

Monitored Packets

Provide disable and enable the Port Mirroring function, the available options are Disable, RX,

TX, TX & RX. Default mode is Disable.

Destination Port

The destination port can be used to see all monitor port traffic. It can connect destination port to

LAN analyzer or Netxray.

Source Port

Apply button

The source port that want to monitor. All monitor port traffic will be copied to destination port.

Press this button for save current configuration of Web Smart Switch.

Table 4-5 Descriptions of the Port Mirroring Screen Objects

- 30 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.3 Bandwidth Control

This section introduces detail settings of Bandwidth Control function of Web Smart Switch; the screen in Figure 4-22

appears and Table 4-6 description the Bandwidth Control objects of Web Smart Switch.

Figure 4-22 Bandwidth Control Web Page Screen

Object

Description

Port

Indicate port 1 to port 24 (FGSW-2620CS), port 1 to port 16 (FGSW-1820CS)

Tx Rate

Provide No Limit, 1Mbps, 2Mbps, 4Mbps, 8Mbps, 16Mbps, 32Mbps, 64Mbps different

transmit rate for bandwidth control function of Web Smart Switch. Default mode is “No Limit”.

Provide No Limit, 1Mbps, 2Mbps, 4Mbps, 8Mbps, 16Mbps, 32Mbps, 64Mbps different re-

ceive rate for bandwidth control function of Web Smart Switch. Default mode is “No Limit”.

Press this button for save current configuration of each port on Web Smart Switch.

Rx Rate

Apply button

Table 4-6 Descriptions of the Bandwidth Control Screen Objects

- 31 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.4 Broadcast Storm Control

This section introduces detail settings of Broadcast Storm Control function of Web Smart Switch; the screen in Figure 4-23

appears and Table 4-7 descriptions the Broadcast Storm Control objects of Web Smart Switch.

Figure 4-23 Broadcast Storm Control Web Page Screen

Object

Filter Mode

Apply button

Description

Provide 5%, 10%, 25%, 50%, Disable different filter mode. Default mode is Disable.

Press this button for save current configuration of Web Smart Switch.

Table 4-7 Descriptions of the Broadcast Storm Control Screen Objects

- 32 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3.5 Port Statistics

This section introduces detail information of Port Statistics function of Web Smart Switch; the screen in Figure 4-24 ap-

pears and Table 4-8 descriptions the Port Statistics objects of Web Smart Switch.

Figure 4-24 Port Statistics Web Page Screen

Object

Description

Counter Mode

Selection

Provide different type of Ethernet traffic counter mode, the available options are shown as below:

Receive Packet & Transmit Packet

collision Count & Transmit Packet

Drop Packet & Receive Packet

CRC error Packet & Receive Packet

Default mode is Receive Packet & Transmit Packet.

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Port

Transmit

Receive

Display Transmit count value from each port.

Display Receive count value from each port.

Refresh button

Clear button

Press this button for refresh the Port Statistics value of Web Smart Switch.

Press this button for clear the Port Statistics value of Web Smart Switch.

Table 4-8 Descriptions of the Port Statistics Screen Objects

- 33 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4 VLAN Setting

A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic

so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is

logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network devices

are still plug into the same switch physically.

The Switch supports IEEE 802.1Q (tagged-based) and Port-Base VLAN setting in web management page. In the default

configuration, VLAN support is “No VLAN”.

Port-based VLAN

Port-based VLAN limit traffic that flows into and out of switch ports. Thus, all devices connected to a port are members of

the VLAN(s) the port belongs to, whether there is a single computer directly connected to a switch, or an entire department.

On port-based VLAN.NIC do not need to be able to identify 802.1Q tags in packet headers. NIC send and receive normal

Ethernet packets. If the packet's destination lies on the same segment, communications take place using normal Ethernet

protocols. Even though this is always the case, when the destination for a packet lies on another switch port, VLAN con-

siderations come into play to decide if the packet is dropped by the Switch or delivered.

IEEE 802.1Q VLANs

IEEE 802.1Q (tagged) VLAN are implemented on the Switch. 802.1Q VLAN require tagging, which enables them to span

the entire network (assuming all switches on the network are IEEE 802.1Q-compliant).

VLAN allow a network to be segmented in order to reduce the size of broadcast domains. All packets entering a VLAN will

only be forwarded to the stations (over IEEE 802.1Q enabled switches) that are members of that VLAN, and this includes

broadcast, multicast and unicast packets from unknown sources.

VLAN can also provide a level of security to your network. IEEE 802.1Q VLAN will only deliver packets between stations

that are members of the VLAN. Any port can be configured as either tagging or untagging. The untagging feature of IEEE

802.1Q VLAN allows VLAN to work with legacy switches that don't recognize VLAN tags in packet headers. The tagging

feature allows VLAN to span multiple 802.1Q-compliant switches through a single physical connection and allows Span-

ning Tree to be enabled on all ports and work normally.

Any port can be configured as either tagging or untagging. The untagging feature of IEEE 802.1Q VLAN allows VLAN to

work with legacy switches that don’t recognize VLAN tags in packet headers. The tagging feature allows VLAN to span

multiple 802.1Q-compliant switches through a single physical connection and allows Spanning Tree to be enabled on all

ports and work normally.

Some relevant terms:

Tag - The act of putting 802.1Q VLAN information into the header of a packet.

Untag - The act of stripping 802.1Q VLAN information out of the packet header.

802.1Q VLAN Tags

The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address.

Their presence is indicated by a value of 0x8100 in the Ether Type field. When a packet's Ether Type field is equal to

0x8100, the packet carries the IEEE 802.1Q/802.1p tag. The tag is contained in the following two octets and consists of 3

bits of user priority, 1 bit of Canonical Format Identifier (CFI - used for encapsulating Token Ring packets so they can be

carried across Ethernet backbones), and 12 bits of VLAN ID (VID). The 3 bits of user priority are used by 802.1p. The VID

is the VLAN identifier and is used by the 802.1Q standard. Because the VID is 12 bits long, 4094 unique VLAN can be

identified.

The tag is inserted into the packet header making the entire packet longer by 4 octets. All of the information originally

contained in the packet is retained.

- 34 -

Download from Www.Somanuals.com. All Manuals Search And Download.

802.1Q Tag

User Priority

3 bits

CFI

VLAN ID (VID)

12 bits

1 bits

TPID (Tag Protocol Identifier)

2 bytes

TCI (Tag Control Information)

2 bytes

Destination

Address

Source Ad-

dress

Ethernet

Type

Preamble

VLAN TAG

4 bytes

Data

46-1517 bytes

FCS

6 bytes 6 bytes

2 bytes

4 bytes

The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or

Logical Link Control. Because the packet is now a bit longer than it was originally, the Cyclic Redundancy Check (CRC)

must be recalculated.

Adding an IEEE802.1Q Tag

Dest. Addr.

Src. Addr.

Length/E. type

Data

Old CRC

Original Ethernet

Data New CRC

Dest. Addr.

Src. Addr.

E. type

Tag

Length/E. type

New Tagged Packet

Priority

CFI

VLAN ID

Port VLAN ID

Packets that are tagged (are carrying the 802.1Q VID information) can be transmitted from one 802.1Q compliant network

device to another with the VLAN information intact. This allows 802.1Q VLAN to span network devices (and indeed, the

entire network – if all network devices are 802.1Q compliant).

Every physical port on a switch has a PVID. 802.1Q ports are also assigned a PVID, for use within the switch. If no VLAN

are defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are

assigned the PVID of the port on which they were received. Forwarding decisions are based upon this PVID, in so far as

VLAN are concerned. Tagged packets are forwarded according to the VID contained within the tag. Tagged packets are

also assigned a PVID, but the PVID is not used to make packet forwarding decisions, the VID is.

Tag-aware switches must keep a table to relate PVID within the switch to VID on the network. The switch will compare the

VID of a packet to be transmitted to the VID of the port that is to transmit the packet. If the two VID are different the switch

will drop the packet. Because of the existence of the PVID for untagged packets and the VID for tagged packets, tag-aware

and tag-unaware network devices can coexist on the same network.

A switch port can have only one PVID, but can have as many VID as the switch has memory in its VLAN table to store them.

Because some devices on a network may be tag-unaware, a decision must be made at each port on a tag-aware device

before packets are transmitted – should the packet to be transmitted have a tag or not? If the transmitting port is connected

to a tag-unaware device, the packet should be untagged. If the transmitting port is connected to a tag-aware device, the

packet should be tagged.

Default VLANs

The Switch initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the

Switch to the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed

from the "default."

Base on the Switch chipset specification, the Switch supports SVL(Shared VLAN Learning) ,

#Notice:

all VLAN groups share the same Layer 2 learned MAC address table.

- 35 -

Download from Www.Somanuals.com. All Manuals Search And Download.

„

VLAN Settings

This section provides VLAN Configuration from Web Smart Switch, the screen in Figure 4-25 appears and Table 4-9

describes the VLAN Configuration object of Web Smart Switch.

Figure 4-25 VLAN Setting Web Page Screen

Object

Description

VLAN Mode

Provide different VLAN operation mode, the available options are shown as below:

No VLAN

Port Based VLAN. Explained in section 4.4.1.

802.1Q VLAN. Explained in section 4.4.3.

MTU. Explained in section 4.4.5.

Default mode is No VLAN.

Apply button

Press this button for save current configuration of Web Smart Switch.

Table 4-9 Descriptions of the VLAN Setting Screen Objects

- 36 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4.1 Port Based VLAN

This section introduces detail information of Port Based VLAN function of Web Smart Switch; Choose “Port Based VLAN”

from VLAN from the VLAN Mode and press “Apply” button to enable the port based VLAN function. The screen in Figure

4-26 & 4-27 & 4-28 appears and Table 4-10 description the Port Based VLAN objects of Web Smart Switch.

Figure 4-26 Port Based VLAN Configuration Web Page Screen

Figure 4-27 Port Based VLAN Configuration Web Page Screen

- 37 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4-28 Port Based VLAN Configuration Web Page Screen

Object

Description

VID

Display different VLAN ID from multi-port based VLAN groups.

VLAN Name

Assign and display different VLAN name from multi-port based VLAN groups. Up to maximum 8

characters allow.

Port

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Member

Allow to click specific port as member port from different port based VLAN groups.

Press this button for save current configuration of Web Smart Switch.

Press this button for delete existence port based VLAN groups.

Apply button

Delete Group

Add New Group

Press this button for create a new port based VLAN groups. Up to maximum 18 port based VLAN

groups on FGSW-1820CS and 26 port based VLAN groups on FGSW-2620CS.

Table 4-10 Descriptions of the VLAN Setting Screen Objects

4.4.2 Port Based VLAN Setting example:

VLAN scenario

1. Port 26 is the file server port for all the workstations

2. Port 1 to port 25 is different devices that do not need to see each other

Setup steps

1. Port Setting

1.1 Assign VLAN 1 for the first VLAN group with port 1 and port 26.

1.2 Assign VLAN 2 for the second VLAN group with port 2 and port 26

1.3 Repeat the same steps for port 3 to port 25. i.e. 3 & 26, 4 & 26, ….., 25 & 26

- 38 -

Download from Www.Somanuals.com. All Manuals Search And Download.

After the above steps port 1 to port 25 is being separated physically due to it belongs to different VLAN groups (different

VLAN). However, they all can access port 26 due to port 26 is using overlapping feature to communicate with port 1 to port

25.

4.4.3 802.1Q VLAN

This section introduces detail information of IEEE 802.1Q VLAN function of Web Smart Switch; Choose “802.1Q VLAN”

from VLAN from the VLAN Mode and press “Apply” button to enable the 802.1Q VLAN function. The screen in Figure 4-29

& 4-30 & 4-31 appears and Table 4-11 description the 802.1Q VLAN objects of Web Smart Switch.

Figure 4-29 802.1Q VLAN Configuration Web Page Screen

Figure 4-30 802.1Q VLAN Configuration Web Page Screen

- 39 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4-31 802.1Q VLAN Configuration Web Page Screen

Object

Description

Group

Display the existence 802.1Q VLAN groups.

VID

Display different VLAN ID from multi-802.1Q VLAN groups.

VLAN Name

Assign and display different VLAN name from multi-802.1Q VLAN groups. Up to maximum 8 char-

acters allow.

Port

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Member

Allow to click specific port as member port from different 802.1Q VLAN groups.

Press this button for save current configuration of Web Smart Switch.

Allow to define per port UnTag / Tag, Uplink and PVID. The screen in Figure 4-32 appears.

Press this button for delete existence 802.1Q VLAN groups.

Apply button

Per Port Setting

Delete Group

Add New Group

Press this button for create a new 802.1Q VLAN groups. Up to maximum 32 802.1Q VLAN groups

support on Web Smart Switch

Table 4-11 Descriptions of the 802.1Q VLAN Setting Screen Objects

- 40 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 4-32 802.1Q VLAN Per Port Setting Web Page Screen

This section introduces detail information of IEEE 802.1Q VLAN Per Port Setting of Web Smart Switch; The Table 4-12

description the 802.1Q VLAN Per Port Setting objects of Web Smart Switch.

Object

Description

Port

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Define UnTag or Tag on each port of Web Smart Switch. Default mode is “UnTag”.

Define No Uplink or Uplink on each port of Web Smart Switch. Default mode is “No Uplink”.

Assign PVID on each port of Web Smart Switch. Default PVID is “1”.

Press this button for save current configuration of Web Smart Switch.

Return to 802.1Q VLAN Group Setting screen.

Link Type

Uplink

PVID

Apply button

VLAN Group Setting

Table 4-12 Descriptions of the 802.1Q VLAN Per Port Setting Screen Objects

- 41 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4.4 802.1Q VLAN Setting example

Two separate 802.1Q VLAN scenario

1. Shows how the Web Smart Switch handles Untagged and Tagged traffic from two 802.1Q VLAN groups.

2. Each VLAN isolate network traffic, only the same VLAN member port can receive traffic from each other.

Figure 4-33 two separate 802.1Q VLAN diagram

VLAN Group

VLAN Group 1

VLAN Group 2

VLAN Group 3

VID

Untagged Members

Port-7~Port-24

Port-1,Port-2

Tagged Members

N/A

Port-3

Port-4,Port-5

Port-6

Table 4-13 VLAN and Port Configuration

The scenario described as follow:

„

Untagged packet entering VLAN 2

While [PC-1] transmit an untagged packet enters Port-1, the Web Smart Switch will tag it with a VLAN Tag=2.

[PC-2] and [PC-3] will received the packet through Port-2 and Port-3.

[PC-4], [PC-5] and [PC-6] received no packet.

While the packet leaves Port-2, it will be stripped away it tag becoming an untagged packet.

While the packet leaves Port-3, it will keep as a tagged packet with VLAN Tag=2.

„

Tagged packet entering VLAN 2

While [PC-3] transmit a tagged packet with VLAN Tag=2 enters Port-3, [PC-1] and [PC-2] will received the

packet through Port-1 and Port-2.

While the packet leaves Port-1 and Port-2, it will be stripped away it tag becoming an untagged packet.

Untagged packet entering VLAN 3

While [PC-4] transmit an untagged packet enters Port-4, the switch will tag it with a VLAN Tag=3. [PC-5] and

[PC-6] will received the packet through Port-5 and Port-6.

While the packet leaves Port-5, it will be stripped away it tag becoming an untagged packet.

While the packet leaves Port-6, it will keep as a tagged packet with VLAN Tag=3.

At this example, VLAN Group 1 just set as default VLAN, but only focus on VLAN 2,

#Notice:

VLAN 3 traffic flow.

- 42 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup steps

1. Create VLAN Group:

Set VLAN Group 1 = default-VLAN with VID (VLAN ID) =1.

Add two VLANs – VLAN 2 and VLAN 3, VLAN Group 2 with VID=2, VLAN Group 3 with VID=3.

Figure 4-34 Add new VLAN Group Screen

2. Assign VLAN Member :

VLAN 2 : Port-1,Port-2 and Port-3. VLAN 3 : Port-4, Port-5 and Port-6. VLAN 1: All other ports – Port-7~Port-24.

Figure 4-35 Assign VLAN members for VLAN 2 and VLAN 3

- 43 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Please remember to remove the Port 1 – Port 6 from VLAN 1 membership, since the Port 1 – Port 6 had been assigned to

VLAN 2 and VLAN 3.

Figure 4-36 Remove specify ports from VLAN 1 member

Its import to remove the VLAN member port from VLAN 1 group. Or the ports

#Notice:

would become overlapping setting.

- 44 -

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Assign PVID for each port:

Port-1,Port-2 and Port-3 : PVID=2.

Port-4,Port-5 and Port-6 : PVID=3.

Port-7~Port-24 : PVID=1.

4. Enable VLAN Tag for specific ports

Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3).

The Per Port VLAN configuration in Figure 4-37 appears.

Figure 4-37 Port 1-Port 6 802.1Q VLAN Configuration

Two separate 802.1Q VLAN with overlapping area scenario

Based on the two separate VLAN group examples above, VLAN 2 and VLAN 3 member port cannot see each other.

The member ports from VLAN 2 and VLAN 3 need to access one public server.

Figure 4-38 A Server connect to the VLAN overlapping area

1. Specify Port-7 on the Web Smart Switch that connects to the server.

- 45 -

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Assign Port-7 to both VLAN 2 and VLAN 3 at the VLAN Member configuration page. The screen in Figure 4-39

appears.

Figure 4-39 VLAN overlap port setting

3. Define a VLAN 1 as a “Public Area” that overlapping with both VLAN 2 members and VLAN 3 members.

Figure 4-40 VLAN 1 – The public area member assign

- 46 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Setup Port-7 with “PVID=1” at VLAN Per Port Configuration page. The screen in Figure 4-41 appears.

Figure 4-41 Setup Port-7 with PVID-1

Although the VLAN 2 members: Port-1 to Port-3 and VLAN 3 members: Port-4 to Port-6 also belongs to VLAN 1. But with

different PVID settings, packets form VLAN 2 or VLAN 3 is not able to access to the other VLAN.

- 47 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4.5 MTU VLAN

This section introduces detail information of MTU VLAN function of Web Smart Switch; Choose “MTU” from VLAN from

the VLAN Mode and press “Apply” button to enable the MTU VLAN function. The screen in Figure 4-42 appears and

Table 4-14 description the MTU VLAN objects of Web Smart Switch.

Figure 4-42 MTU VLAN Configuration Web Page Screen

Object

MTU Port

Description

Indicate the MTU Port of Web Smart Switch.

Member Port

Apply button

Indicate the Member Port of Web Smart Switch.

Press this button for save current configuration of Web Smart Switch.

Table 4-14 Descriptions of the MTU VLAN Setting Screen Objects

- 48 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.5 Trunk

Port link aggregations can be used to increase the bandwidth of a network connection or to ensure fault recovery. Link

aggregation lets you group up to 4 consecutive ports into a single dedicated connection between any two the Switch or

other Layer 2 switches. However, before making any physical connections between devices, use the Link aggregation

Configuration menu to specify the link aggregation on the devices at both ends. When using a port link aggregation, note

that:

。

The ports used in a link aggregation must all be of the same media type (RJ-45, 100 Mbps fiber).

The ports that can be assigned to the same link aggregation have certain other restrictions (see below).

Ports can only be assigned to one link aggregation.

The ports at both ends of a connection must be configured as link aggregation ports.

None of the ports in a link aggregation can be configured as a mirror source port or a mirror target port.

Enable the link aggregation prior to connecting any cable between the switches to avoid creating a data loop.

Disconnect all link aggregation port cables or disable the link aggregation ports before removing a port link aggre-

gation to avoid creating a data loop.

It allows a maximum of 4 ports to be aggregated at the same time and up to 2 groups. If the group is defined as

a local static link aggregation group, then the number of ports must be the same as the group member ports.

- 49 -

Download from Www.Somanuals.com. All Manuals Search And Download.

„

Trunk Setting

This function allows to configuring the trunk function. It provides up to two trunk groups and each trunk group provides 4

member ports. Also provide four various Trunk Hash Algorithm policies for selection. The screen in Figure 4-43 appears

and Table 4-15 description the Trunk Setting objects of Web Smart Switch.

Figure 4-43 Trunk Setting Web Page Screen

Object

Description

Trunk Hash Algorithm

selection

Provide four various Trunk Hash Algorithm polices, the available options are shown as below:

SA & DA(Default)

Port ID

Default mode is SA & DA.

Trunk1

Trunk2

Apply

Indicate the Trunk Member Port 1,2,3,4 of Web Smart Switch.

Indicate the Trunk Member Port 5,6,7,8 of Web Smart Switch.

Press this button for save current configuration of Web Smart Switch.

Table 4-15 Descriptions of the Trunk Setting Screen Objects

- 50 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.6 QoS Setting

This function provides QoS Setting of Web Smart Switch; the screen in Figure 4-44 appears and Table 4-16 descriptions

the QoS Setting of Web Smart Switch.

Figure 4-44 QoS Setting Web Page Screen

Object

Description

Priority Mode

Provide three different Priority polices on Web Smart Switch. Explained in section 4.6.1.

Provide three different polices on each port of Web Smart Switch. Explained in section 4.6.2.

Class of Service Con-

figuration

TCP/UDP Port Based

QoS

Allow to define various QoS mode on TCP / UDP port. Explained in section 4.6.3.

Table 4-16 Descriptions of the QoS Setting Screen Objects

- 51 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.6.1 Priority Mode

This section introduces detail information of Priority Mode of Web Smart Switch; the screen in Figure 4-45 appears and

Table 4-17 descriptions the Priority Mode of Web Smart Switch.

Figure 4-45 Priority Mode Web Page Screen

Object

Description

Priority Mode

Provide three different Priority polices on Web Smart Switch, the available options are shown as

below:

Fist-In-First-Out

All-High-Before-Low

Weight-Round-Robin= Low weight (0-7 range) : High weight (0-7 range)

Default mode is First-In-First-Out.

Apply

Press this button for save current configuration of Web Smart Switch.

Table 4-17 Descriptions of the Priority Mode Screen Objects

- 52 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.6.2 Class of Service Configuration

This section introduces detail information of Class of Service Configuration of Web Smart Switch; the screen in Figure 4-46

appears and Table 4-18 descriptions the Class of Service Configuration of Web Smart Switch.

Figure 4-46 Class of Service Configuration Web Page Screen

Object

Enable High Priority

Port

Description

Allow to disable or enable the High Priority function. Default mode is Enable.

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Define per port Class of Service policy based on Port Base policy.

Define per port Class of Service policy based on VLAN Tag priority policy.

Define per port Class of Service policy based on IP / DS policy.

Press this button for save current configuration of Web Smart Switch.

Port Base

VLAN Tag

IP /DS

Apply

Table 4-18 Descriptions of the Class of Service Configuration Screen Objects

„

VLAN Priority tag value define

IEEE 802.1p priority value from VLAN tag

User priority values= 4~7

High Priority

Low Priority

User priority values= 0~3

- 53 -

Download from Www.Somanuals.com. All Manuals Search And Download.

„

IP TOS/DSCP Priority value define

TOS/DSCP Value

AF11

AF21

AF31

AF41

High Priority

Low Priority

DSCP 46

(101110)

DSCP 10

(001010)

DSCP 18

(010010)

DSCP 26

(011010)

DSCP 34

(100010)

Other DSCP values

DSCP: Differentiated Services Code Point

EF: Expected Forwarding

AF: Assured Forwarding

- 54 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.6.3 TCP / UDP Port Based QoS

This section introduces detail information of TCP / UDP Port Based QoS Configuration of Web Smart Switch; the screen in

Figure 4-47 & 4-48 appears and Table 4-19 descriptions the TCP / UDP Port Based QoS Configuration of Web Smart

Switch.

Figure 4-47 TCP / UDP Port Based QoS Configuration Web Page Screen

Figure 4-48 TCP / UDP Port Based QoS Configuration Web Page Screen

- 55 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Object

Description

Protocol

Display different Protocol for define the QoS policy in option

Provide F-I-F-O, Discard, Low, High options.

FTP(20,21)

SSH(22)

TELNET(23)

SMTP(25)

DNS(53)

TFTP(69)

Provide Low, High options.

HTTP(80,8080)

POP3(110)

Provide Low, High options.

Provide F-I-F-O, Discard, Low, High options.

Provide Low, High options.

NEWS(119)

SNTP(123)

NetBIOS(137~139)

IMAP(143,220)

SNMP(161,162)

HTTPS(443)

MSN(1863)

XRD_RDP(3389)

QQ(4000,8000)

ICQ(5190)

Yahoo(5050)

BOOTP_DHCP(67,68)

User_Define_a

User_Define_b

User_Define_c

User_Define_d

Provide F-I-F-O, Discard, Low, High options.

User_Define

Port number

(1~65535)

Allow to define 4 protocol port numbers, such as Port and Mask. The available options are

shown as below:

User_Define_a

User_Define_b

Mask(0~255)

User_Define_c

User_Define_d

Disable

Allow to choose “Disable” or “Enable” options. Default mode is Disable.

Not Override

Apply

Allow to choose “Override” or “Not Override” options. Default mode is Not Override .

Press this button for save current configuration of Web Smart Switch.

Table 4-19 Descriptions of the TCP / UDP Port Based QoS Configuration Screen Objects

- 56 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.7 Security Filter

This function provides Security Filter of Web Smart Switch; the screen in Figure 4-49 appears and Table 4-20 descriptions

the Security Filter of Web Smart Switch.

Figure 4-49 Security Filter Web Page Screen

Object

Description

MAC Address Filter

TCP/UDP Filter

Allow define three MAC Address on per port of Web Smart Switch. Explained in section 4.7.1.

Allow define the filter policy of TCP / UDP flow on Web Smart Switch. Explained in section

4.7.2.

Table 4-20 Descriptions of the Security Filter Web Page Screen Objects

- 57 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.7.1 MAC Address Filter

This section introduces detail information of MAC Address Filter of Web Smart Switch; the screen in Figure 4-50 appears

and Table 4-21 & 4-22 descriptions the MAC Address Filter of Web Smart Switch.

Figure 4-50 MAC Address Filter Web Page Screen

Object

MAC Address

Select Port

Binding

Description

Allow to input three MAC Address on per port of Web Smart Switch.

Allow to select port 1 to port 26 (FGSW-2620CS) or port 1 to port 18 (FGSW-1820CS).

Allow to Disable or Enable the binding function on each port of Web Smart Switch.

Press this button for save current configuration of Web Smart Switch.

Apply

Table 4-21 Descriptions of the MAC Address Filter Screen Objects

Object

Port

Description

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS).

Display Binding Status from each port of Web Smart Switch.

Binding Status

MAC 1

Display first assigns MAC Address on each port of Web Smart Switch.

Display second assigns MAC Address on each port of Web Smart Switch.

Display third assigns MAC Address on each port of Web Smart Switch.

MAC 2

MAC 3

Table 4-22 Descriptions of the MAC Address Filter Screen Objects

- 58 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.7.2 TCP / UDP Filter

This section introduces detail information of TCP / UDP Filter of Web Smart Switch; the screen in Figure 4-51 & 4-52

appears and Table 4-23 descriptions the TCP / UDP Filter Configuration of Web Smart Switch.

Figure 4-51 TCP / UDP Filter Web Page Screen

Figure 4-52 TCP / UDP Filter Web Page Screen

- 59 -

Download from Www.Somanuals.com. All Manuals Search And Download.

Object

Function Enable

Port Filtering Rule

Protocol

Description

Allow to Disable or Enable the TCP / UDP Filter function. Default mode is Disable.

Allow to Forward or Block the Port Filtering Rule. Default mode is Block.

Display different Protocol for define the TCP / UDP Filter policy.

FTP(20,21)

SSH(22)

TELNET(23)

SMTP(25)

DNS(53)

TFTP(69)

HTTP(80,8080)

POP3(110)

NEWS(119)

SNTP(123)

NetBIOS(137~139)

IMAP(143,220)

SNMP(161,162)

HTTPS(443)

Allow to choose list protocol for filtering

MSN(1863)

XRD_RDP(3389)

QQ(4000,8000)

ICQ(5190)

Yahoo(5050)

BOOTP_DHCP(67,68)

User_Define_a

User_Define_b

User_Define_c

User_Define_d

Secure Egress Port

Indicate port 1 to port 26 (FGSW-2620CS), port 1 to port 18 (FGSW-1820CS). Click specific port

for filtering.

Apply

Press this button for save current configuration of Web Smart Switch.

Table 4-23 Descriptions of the TCP / UDP Filter Configuration Screen Objects

- 60 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.8 Misc Operation

This function provides Misc Operation of Web Smart Switch; the screen in Figure 4-53 appears and Table 4-24 descrip-

tions the Misc Operation of Web Smart Switch.

Figure 4-53 Misc Operation Web Page Screen

Object

Description

Output Queue Aging Time

Allow define the Output Queue Aging Time of Web Smart Switch, the available options

are Disable, 200ms, 400ms, 600ms and 800ms. Default mode is Disable.

Allow Disable or Enable the VLAN Striding function of Web Smart Switch. Default mode

is Disable.

VLAN Striding

IGMP Snooping V1 & V2

Apply

Allow Disable or Enable the IGMP Snooping V1 & V2 function of Web Smart Switch.

Default mode is Disable.

Press this button for save current configuration of Web Smart Switch.

Table 4-24 Descriptions of the Misc Operation Web Page Screen Objects

- 61 -

Download from Www.Somanuals.com. All Manuals Search And Download.

4.9 Logout

This section provide Web logout function on Web Smart Switch, after choose this function and the following screen appears

in Figure 4-54 & 4-55. Please press “Logout” button to take effect and Login Web Screen appears. Please re-login the

Web Smart Switch for further management.

Figure 4-54 Logout Web Page Screen

Figure 4-55 Login Web Page Screen

- 62 -

Download from Www.Somanuals.com. All Manuals Search And Download.

5. SWITCH OPERATION

5.1 Address Table

The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to

store the address information of some node in network, including MAC address, port no, etc. This information comes

from the learning process of Ethernet Switch.

5.2 Learning

When one packet comes in from any port. The Switch will record the source address, port no. And the other related

information in address table. This information will be used to decide either forwarding or filtering for future packets.

5.3 Forwarding & Filtering

When one packet comes from some port of the Ethernet Switching, it will also check the destination address besides

the source address learning. The Ethernet Switching will lookup the address-table for the destination address. If not

found, this packet will be forwarded to all the other ports except the port which this packet comes in. And these ports

will transmit this packet to the network it connected. If found, and the destination address is located at different port

from this packet comes in, the Ethernet Switching will forward this packet to the port where this destination address is

located according to the information from address table. But, if the destination address is located at the same port with

this packet comes in, then this packet will be filtered. Thereby increasing the network throughput and availability.

5.4 Store-and-Forward

Store-and-Forward is one type of packet-forwarding techniques. A Store-and Forward Ethernet Switching stores the

incoming frame in an internal buffer, do the complete error checking before transmission. Therefore, no error packets

occurrence, it is the best choice when a network needs efficiency and stability.

The Ethernet Switch scans the destination address from the packet-header, searches the routing table provided for

the incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for con-

necting servers directly to the network, thereby increasing throughput and availability. However, the switch is most

commonly used to segment existing hubs, which nearly always improves overall performance. An Ethernet Switching

can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional

cabling and adapters.

Due to the learning function of the Ethernet switching, the source address and corresponding port number of each

incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets

whose destination address is on the same segment as the source address. This confines network traffic to its re-

spective domain, reducing the overall load on the network.

The Switch performs "Store and forward" therefore, no error packets occur. More reliably, it reduces the

re-transmission rate. No packet loss will occur.

5.5 Auto-Negotiation

The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible

bandwidth when a connection is established with another network device (usually at Power On or Reset). This is done

by detect the modes and speeds at the second of both device is connected and capable of, both 10Base-T and

100Base-TX devices can connect with the port in either Half- or Full-Duplex mode. 1000Base-T can be only con-

nected in Full-duplex mode.

- 63 -

Download from Www.Somanuals.com. All Manuals Search And Download.

6. TROUBLESHOOTING

This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the

Ethernet Switch was set up according to instructions in this manual.

The Link LED is not lit

Solution:

Check the cable connection and remove duplex mode of the Switch.

Some stations cannot talk to other stations located on the other port

Solution:

Please check the VLAN, port trunking function that may introduce this kind of problem.

Performance is bad

Solution:

Check the full duplex status of the Ethernet Switch. If the Ethernet Switch is set to full duplex and the partner is set to

half duplex, then the performance will be poor.

100Base-TX port link LED is lit, but the traffic is irregular

Solution:

Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to

change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.

Why the Switch doesn’t connect to the network

Solution:

Check the LNK/ACT LED on the switch Try another port on the Switch Make sure the cable is installed properly Make

sure the cable is the right type Turn off the power. After a while, turn on power again.

How to deal forgotten password situation of FGSW-1820CS / FGSW-2620CS?

Solution:

Please press Reset button at front panel for 5 seconds then the Web Smart Switch will reset to

factory default mode(username and password: admin)

- 64 -

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX A NETWORKING CONNECTION

A.1 Switch‘s RJ-45 Pin Assignments

1000Mbps, 1000Base T

RJ-45 Connector pin assignment

Contact

MDI

MDI-X

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

BI_DB+

BI_DB-

BI_DA+

BI_DD+

BI_DD-

BI_DA-

BI_DC+

BI_DC-

10/100Mbps, 10/100Base-TX

RJ-45 Connector pin assignment

MDI

MDI-X

Contact

Media Dependant In-

terface

Media Dependant

Interface -Cross

Tx + (transmit)

Tx - (transmit)

Rx + (receive)

Rx - (receive)

Tx + (transmit)

4, 5

Not used

Rx - (receive)

Tx - (transmit)

7, 8

Not used

A.2 RJ-45 cable pin assignment

321

The standard RJ-45 receptacle/connector

- 65 -

Download from Www.Somanuals.com. All Manuals Search And Download.

There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation

and color of straight cable and crossover cable connection:

Figure A-1: Straight-Through and Crossover Cable

Please make sure your connected cables are with same pin assignment and color as above picture before deploying the

cables into your network.

2080-A81150-000

- 66 -

Download from Www.Somanuals.com. All Manuals Search And Download.

EC Declaration of Conformity

For the following equipment:

*Type of Product: 16-Port 10/100Base-TX + 2G TP/SFP Combo Web Smart Switch

*Model Number: FGSW-1820CS

* Produced by:

Manufacturer‘s Name

Planet Technology Corp.

Manufacturer‘s Address:

11F, No 96, Min Chuan Road

Hsin Tien, Taipei, Taiwan , R. O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on (89/336/EEC,92/31/EEC,93/68/EEC).

For the evaluation regarding the EMC, the following standards were applied:

Emission

Conducted / Radiated EN 55022

Harmonic

Flicker

Immunity

ESD

EFT/ Burst

Surge

EN 50081-1

(1992)

(1998)

(1995)

(1998)

(1995)

(1996)

(1995)

(1996)

(1994)

EN 61000-3-2

EN 61000-3-3

EN 55024

EN 61000-4-2

EN 61000-4-3

EN 61000-4-4

EN 61000-4-5

EN 61000-4-6

EN 61000-4-11

Voltage Disp

Responsible for marking this declaration if the:

⌧ Manufacturer ꢀ Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C

Person responsible for making this declaration

Name, Surname

Position / Title :

Kent Kang

Product Manager

Taiwan

Place

22th Feb, 2008

Date

Legal Signature

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw

11F, No. 96, Min Chuan Road, Hsin Tien, Taip

http://www.planet.com.tw

Download from Www.Somanuals.com. All Manuals Search And Download.

EC Declaration of Conformity

For the following equipment:

*Type of Product:

*Model Number:

24-Port 10/100Base-TX + 2G TP/SFP Combo Web Smart Switch

FGSW-2620CS

* Produced by:

Manufacturer‘s Name

Planet Technology Corp.

Manufacturer‘s Address:

11F, No 96, Min Chuan Road

Hsin Tien, Taipei, Taiwan , R. O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

Directive on (89/336/EEC).

For the evaluation regarding the EMC, the following standards were applied:

Emission

Harmonic

EN 55022

EN 61000-3-2

(1998 + 2000 Class A)

(1995 + A1:1998 + A2:1998 +

A14:2000)

Flicker

Immunity

ESD

EFT/ Burst

Surge

EN 61000-3-3

EN 55024

(1995 + A1:2001)

(1998 + A1:2001 + A2:2003)

(1995 + A1:1998 + A2:2001)

(1995 + A1:2001 + A2:2001)

(1995 + A1:2001)

(1996 + A1:2001)

(1993 + A1:2001)

(1994 + A1:2001)

IEC 61000-4-2

IEC 61000-4-3

IEC 61000-4-4

IEC 61000-4-5

IEC 61000-4-6

IEC 61000-4-8

IEC 61000-4-11

Magnetic Field

Voltage Disp

Responsible for marking this declaration if the:

⌧ Manufacturer

ꢀ Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name:

Planet Technology Corp.

Company Address: 11F, No.96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C

Person responsible for making this declaration

Name, Surname

Position / Title :

Kent Kang

Product Manager

Taiwan

22th Feb, 2008

Place

Date

Legal Signature

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw

11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

http://www.planet.com.tw

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Music Mixer Series 500 User Manual
Philips Computer Monitor 107B55 User Manual
Philips Juicer HR1821 User Manual
Philips MP3 Docking Station AJ301D 12 User Manual
Philips MP3 Docking Station DC290 05 User Manual
Philips Security Camera G8027 1 User Manual
Philips TV Cables MWS2823T User Manual
Philips TV Receiver SLV3105 User Manual
Pioneer Portable DVD Player AVH X6500DVD User Manual
Porter Cable Nail Gun FRP350 User Manual