Planet Technology Network Router ADE 3410v2 User Manual

ADSL 2/2+ Router with USB

Port

ADE-3410v2

User's Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF

THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio

equipment and telecommunication terminal Equipment and the mutual recognition of

their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As

of April 8, 2000.

WEEE

To avoid the potential effects on the environment and human health as a result

of the presence of hazardous substances in electrical and electronic equipment,

end users of electrical and electronic equipment should understand the meaning

of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted

municipal waste and have to collect such WEEE separately.

Safety

This equipment is designed with the utmost care for the safety of those who install and

use it. However, special attention must be paid to the dangers of electric shock and

static electricity when working with electrical equipment. All guidelines of this and of

the computer manufacture must therefore be allowed at all times to ensure the safe use

of the equipment.

Revision

User’s Manual for ADSL 2/2+ Router with USB Port

Model: ADE-3410v2

Rev: 1.0 (Nov. 2007)

Part No. EM-ADE3410v2

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

1. Introduction................................................................................................. 6

1.1 Features.......................................................................................... 6

1.2 Package Contents .......................................................................... 7

1.3 Physical Details ............................................................................. 7

2. Installation................................................................................................... 9

2.1 System Requirement ..................................................................... 9

2.2 Hardware Installation .................................................................. 10

2.3 Router Parameters Settin g ........................................................... 11

2.4 Factory Reset Butto n ................................................................... 12

2.5 USB Installation .......................................................................... 12

3. Introduction to WEB Configuratio n ......................................................... 14

3.1 Quick Setup ................................................................................. 14

3.1.1 Quick Setu p ........................................................................ 15

3.2 Preparations before Login ROUTE R .......................................... 18

3.3 Logging on the ROUTER ........................................................... 18

3.4 System Status .............................................................................. 19

3.4.1 Summary ............................................................................ 19

3.4.2 WAN .................................................................................. 20

3.4.3 Statistics -- LAN................................................................. 21

3.4.4 Statistics -- WAN ............................................................... 21

3.4.5 Statistics -- AT M ................................................................ 22

3.4.6 Statistics -- ADSL .............................................................. 22

3.4.7 Route .................................................................................. 23

3.4.8 ARP .................................................................................... 24

3.4.9 DHCP ................................................................................. 24

3.5 Advanced Setup........................................................................... 25

3.5.1 WAN .................................................................................. 25

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5.2 LAN.................................................................................... 36

3.5.3 NAT.................................................................................... 37

3.5.4 Security............................................................................... 41

3.5.5 Routing ............................................................................... 43

3.5.6 DN S .................................................................................... 45

3.5.7 DSL .................................................................................... 46

3.6 Diagnostics .................................................................................. 47

3.7 Management ................................................................................ 47

3.7.1 Settings ............................................................................... 47

3.7.2 System Log......................................................................... 49

3.7.3 Internet Tim e ...................................................................... 50

3.7.4 Access Control ................................................................... 50

3.7.5 Update Softwar e ................................................................. 52

3.7.6 Save/Reboot........................................................................ 53

4. Networking Topology............................................................................... 53

4.1 PPP over ATM (PPPoA) Mode................................................... 53

4.2 PPP over Ethernet (PPPoE) Mode .............................................. 55

4.3 MER+DHCP Mod e ..................................................................... 56

4.4 IP over ATM (IPoA) +NAT Mode ............................................. 58

4.5 Leased Line Mod e ....................................................................... 59

4.6 PPP over Ethernet (PPPoE) IP Extension Mode......................... 60

5. Questions & Answers ............................................................................... 61

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

The PLANET ADSL 2/2+ Router, ADE-3410v2, provides office and residential users the

ideal solution for sharing a high-speed ADSL 2/2+ broadband Internet connection on one

Ethernet port and one USB port. It can support downstream transmission rates of up to

24Mbps and upstream transmission rates of up to 3.5Mbps. The product supports PPPoA

(RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 2684 encapsulation over ATM

(bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC1577) to establish a

connection with ISP.

Via the user-friendly management interface, ADE-3410v2 can be managed by

workstations running standard web browsers. Furthermore, ADE-3410v2 provides DHCP

server, NAT, virtual server, DMZ, access control, IP filter, PPTP/IPSec/L2TP

pass-through, DDNS, and UPnP capability.

The ADE-3410v2 also serves as an Internet firewall, protecting your network from being

accessed by outside users. It provides the natural firewall function (Network Address

Translation, NAT). All incoming and outgoing IPs are monitored and filtered. Moreover,

it can be configured to block internal users from accessing to the Internet.

1.1 Features

Internet Access Features

Shared Internet Access All users on the LAN can access the Internet through the

ADE-3410v2 using only a single external IP Address. The local (invalid) IP

Addresses are hidden from external sources. This process is called NAT

(Network Address Translation).

Built-in ADSL 2/2+ Router The ADE-3410v2 provides ADSL 2/2+ router, and

supports all common ADSL connections.

IPoA, PPPoE, PPPoA, Direct Connection Support Various WAN connections

are supported by ADE-3410v2.

Fixed or Dynamic IP Address On the Internet (WAN port) connection, the

ADE-3410v2 supports both Dynamic IP Address (IP Address is allocated on

connection) and Fixed IP Address.

Advanced Internet Functions

Virtual Servers This feature allows Internet users to access Internet servers on

your LAN. The required setup is quick and easy.

Firewall Supports simple firewall with NAT technology and provides option for

access control from Internet, like HTTP, FTP, Telnet, ICMP, and TFTP services.

It also supports IP filtering.

Universal Plug and Play (UPnP) UPnP allows automatic discovery and

configuration of the Broadband Router. UPnP is supported by Windows ME, XP,

or later.

Dynamic DNS Support DDNS, when used with the Virtual Servers feature,

allows users to connect to Servers on your LAN using a Domain Name, even if

you have a dynamic IP address which changes every time you connect.

Download from Www.Somanuals.com. All Manuals Search And Download.

VPN Pass through Support PCs with VPN (Virtual Private Networking)

software using PPTP, L2TP, and IPSec are transparently supported - no

configuration is required.

RIP Routing It supports RIP routing protocol for routing capability.

Simple Network Management Protocol (SNMP) It is an easy way to remotely

manage the router via SNMP.

LAN Features

Dual-Port The ADE-3410v2 incorporates on one Ethernet port and one USB port,

making it easy to create or extend your LAN.

DHCP Server Support Dynamic Host Configuration Protocol provides a

dynamic IP address to PCs and other devices upon request. The ADE-3410v2 can

act as a DHCP Server for devices on your local LAN.

1.2 Package Contents

‧ ADE-3410 Unit

‧ Power Adapter

‧ ADSL Splitter

‧ Quick Installation Guide

‧ User’s Manual CD

‧ RJ-11 (ADSL) cable

‧ RJ-45 cable

‧ USB cable

‧

1.3 Physical Details

Top-mounted LEDs of ADE-3410v2

Download from Www.Somanuals.com. All Manuals Search And Download.

LED Indicator

LED

Meaning

PWR

Link

Lit when power is ON.

Lit when DSL line is connected. Blink when DSL line is training.

Blink when DSL data is transferring.

Data

Lit when connected to an Ethernet device. Blink when data is

Transmitted / Received.

LAN

USB

Lit when the USB port is connected to the PC and working

properly.

Rear Panel of ADE-3410v2

Download from Www.Somanuals.com. All Manuals Search And Download.

Rear panel Port and Button Definition

Port

Power

Switch

Meaning

Power ON/OFF switch

Power

Connect the supplied power adapter to this jack (10 DC, 1A).

After the device is powered on, press it to reset the device or restore

to factory default settings. Reset the device 6 seconds above to

restore the factory default settings (this is used when you can not

Reset

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four

LAN ports when connecting to a PC or an office/home network of

10Mbps or 100Mbps.

Ethernet

USB

Connect the supplied USB cable to this port when connecting to the

Connect the supplied RJ-11 (“telephone”) cable to this port when

connecting to the ADSL/telephone network.

Line

2. Installation

This chapter offers information about installing your router. If you are not familiar with

the hardware or software parameters presented here, please consult your service provider

for the values needed.

2.1 System Requirement

1. Personal computer (PC)

2. Pentium II 233 MHz processor minimum

Download from Www.Somanuals.com. All Manuals Search And Download.

3. 64 MB RAM minimum

4. 20 MB of free disk space minimum

5. Ethernet Network Interface Card

2.2 Hardware Installation

This section describes how to connect and configure the ADE-3410v2.

The DSL router may connect to a PC’s USB or Ethernet. DSL router will support at least

one of connectivity methods. The preferred connectivity method is to use the Ethernet; if

your PC does not support an Ethernet port, you will need to use the USB port and install

additional software.

Note: Connect your DSL router to only one interface (Ethernet or USB).

Note: The USB driver supports Windows machines only.

Please connect the device to you computer as follow:

z If connecting to the splitter, connect the “Line” splitter to wall jack using one

telephone cable

z Use another telephone cable to connect “MODEM” port of the splitter and

“LINE” port of the router. The “phone” port of the splitter can be use to connect

the telephone by a telephone cable.

z Use Ethernet cable to connect “LAN” port of the router and “LAN” port of your

computer.

If do not need to connect to the splitter,

z Connect the router to wall jack with a telephone cable.

z Use Ethernet cable to connect “LAN” port of the router and network adaptor of

Download from Www.Somanuals.com. All Manuals Search And Download.

USB Installation

To connect the DSL router to the PC’s USB port, perform the following:

z Connect the USB cable to the USB port on the DSL router. The cable has two

different connectors; you may have to try both connectors.

z Connect the other end of the USB cable into the PC’s USB port.

2.3 Router Parameters Setting

Configuring computer network card IP address

Configure your network card’s TCP/IP properties to Obtain an IP address automatically

from router, or set the computer’s IP with the same network mask of the router (For

example: router’s IP is 192.168.1.1 / 255.255.255.0).

Then you can set computer’s IP to:

192.168.1.x / 255.255.255.0.

The range for x is from 3 to 253

Web setting interface

Open IE or Netscape Web browser, Input http://192.168.1.1(Router default IP address) in

the address column, then click <ENTER> button, access the following setting interface:

Input user name and password, then click Login key to enter WEB setting interface.

Default setting:

IP Address: 192.168.1.1

Subnet Mask: 255.255.255.0

Username / Password: admin / admin

Main interface

After type right user name and password, the following window will pop up:

Download from Www.Somanuals.com. All Manuals Search And Download.

2.4 Factory Reset Button

The Router may be reset to the original factory default settings by depressing the reset

button for a few seconds while the device is powered on. Use a ballpoint or paperclip to

gently push down the reset button. Remember that this will wipe out any settings stored

in flash memory including user account information and LAN IP settings. The device

settings will be restored to the factory default IP address 192.168.1.1 and the subnet mask

is 255.255.255.0, the default management Username is admin and the default Password is

admin.

2.5 USB Installation

To connect the DSL router to the PC’s USB port, perform the following:

Connect the USB cable to the USB port on the DSL router. The cable has two different

connectors; you may have to try both connectors and the connector is keyed so try

different orientations.

Connect the other end of the USB cable into the PC’s USB port. For the USB installation

on Windows XP, once the PC powers up, a message tips shows Found new hardware on

the system tray.

Then a dialog window Found New Hardware Wizard pop-up, Select Install the software

automatically (Recommended) and insert the Manual and Driver CD-Rom. Click <Next>,

Download from Www.Somanuals.com. All Manuals Search And Download.

the windows will search CD-Rom for the best USB driver.

The dialog prompted you to choose your search and installation options. You can

choose the path of USB drive installation. Click <Next >

The dialog prompted Please wait while the wizard searches, when the USB driver has be

searched by the Windows, Click <Next >

Download from Www.Somanuals.com. All Manuals Search And Download.

Click the button<Finish> to complete the USB driver installation.

3. Introduction to WEB Configuration

3.1 Quick Setup

The Quick Setup allows the user to configure the ADSL router for DSL connectivity and

Internet access. It also guides the user though the WAN network setup first and then the

LAN interface setup. You can either manually customize the router or follow the online

instruction to set up the router.

The ADE-3410v2 supports the following five network operating modes over an ATM

PVC WAN interface.

PPP over Ethernet (PPPoE)

PPP over ATM (PPPoA)

MAC Encapsulated Routing (MER)

IP over ATM (IPoA)

Bridging

The following configuration considerations apply:

The WAN network operating mode operation depends on the service provider’s

configuration on the Central Office side and Broadband Access Server for the PVC. If the

service provider provides PPPoE service, then the connection selection depends on

whether the LAN-side device (typically a PC) is running a PPPoE client or whether the

ADE-3410V2 is to run the PPPoE client. The ADE-3410V2 can support both cases

simultaneously.

If some or none of the LAN-side devices do not run PPPoE client, then select PPPoE. If

every LAN-side device is running a PPPoE client, then select Bridge in PPPoE mode,

Download from Www.Somanuals.com. All Manuals Search And Download.

ADE-3410V2 also supports pass-through PPPoE sessions from the LAN side while

simultaneously running a PPPoE client fro non-PPPoE LAN devices.

NAPT and firewall are always enabled when PPPoE mode is selected, but they can be

enabled or disabled by the user when MER or IPoA is selected, NAPT and firewall are

always disabled when Bridge mode is selected.

Depending on the network operating mode, and whether NAPT and firewall are enabled

or disabled, the main panel will display or hide the NAPT/Firewall menu. For instance, at

initial setup, the default network operating mode is Bridge. The main panel will not show

the NAPT and Firewall menu.

Note: Up to eight PVC profiles can be configured and saved on the flash memory. To

activate a particular PVC profile, you need to navigate all the Quick Setup pages until the

last summary page, then click on the Finish button and reboot the system.

3.1.1 Quick Setup

STEP 1: Click Quick Setup.

STEP 2: Enter the Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI).

Select Enable Quality of Service if required. Click Next.

STEP 3: Then, choose the Encapsulation mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 4: Click Next to display the following screen. Choosing different connection types

pops up different settings requests. Enter appropriate settings that are requested by your

service provider. The following descriptions state each connection type setup separately.

For example, PPP over ATM (PPPoA) and PPP over Ethernet (PPPoE)

1. Select the PPP over ATM (PPPoA) or PPP over Ethernet (PPPoE) radio button and

click Next. The following screen appears:

PPP USERNAME/PPP PASSWORD

The PPP Username and the PPP password requirement are dependent on the particular

requirements of the ISP or the ADSL service provider. The WEB user interface allows a

maximum of 256 characters in the PPP user name and a maximum of 32 characters in

PPP password.

Encapsulation Mode

Choosing different connection types provides different encapsulation modes.

PPPoA- VC/MUX, LLC/ENCAPSULATION

PPPoE- LLC/SNAP BRIDGING, VC/MUX

MER- LLC/SNAP-BRIDGING, VC/MUX

IPoA- LLC/SNAP-ROUTING, VC MUX

Bridging- LLC/SNAP-BRIDGING, VC/MUX

Disconnect if no activity

The ADE-3410v2 can be configured to disconnect if there is no activity for a period of

time by selecting the Disconnect if no activity check box. When the checkbox is ticked,

you need to enter the inactivity timeout period. The timeout period ranges from 1 minute

to 4320 minutes.

PPP IP Extension

The PPP IP Extension is a special feature deployed by some service providers. Unless

your service provider specially requires this setup, do not select it. The PPP IP Extension

supports the following conditions:

Allows only one PC on the LAN

The public IP address assigned by the remote side using the PPP/IPCP protocol is

actually not used on the WAN PPP interface. Instead, it is forwarded to the PC’s LAN

interface through DHCP. Only one PC on the LAN can be connected to the remote, since

the DHCP server within the ADSL router has a single IP address to assign to a LAN

device.

NAPT and firewall are disabled when this option is selected.

The ADSL router becomes the default gateway and DNS server to the PC through DHCP

Download from Www.Somanuals.com. All Manuals Search And Download.

using the LAN interface IP address. The ADSL router extends the IP subnet at the remote

service provider to the LAN PC. That is, the PC becomes a host belonging to the same IP

subnet. The ADSL router bridges the IP packets between WAN and LAN ports, unless

the packet is addressed to the router’s LAN IP address.

2. Click Next.

Enable IGMP Multicast checkbox: Tick the checkbox to enable IGMP multicast

(proxy). IGMP (Internet Group Membership Protocol) is a protocol used by IP hosts to

report their multicast group memberships to any immediately neighboring multicast

routers.

Enable WAN Service checkbox: Tick this item to enable the ADSL service. Untick it to

stop the ADSL service.

Service Name: This is user-defined.

3. After entering your settings, select Next. The following screen appears. This page

allows the user to configure the LAN interface IP address, subnet mask and DHCP server.

If the user would like this ADSL router to assign dynamic IP address, DNS server and

default gateways to other LAN devices, select the button Enable DHCP server on the

LAN to enter the starting IP address and end IP address and DHCP leased time.

4. Click Next to display the WAN Setup-Summary screen that presents the entire

configuration summary. Click Save/Reboot if the settings are correct. Click Back if you

wish to modify the settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. After clicking Save/Reboot, the router will save the configuration to the flash memory,

and reboot. The Web UI will not respond until the system is brought up again. After the

system is up, the Web UI will refresh to the Device Info page automatically. The

ADE-3410v2 is ready for operation and the LEDs display as described in the LED

description tables.

You may setup your Router manually. The first time you setup the Router it is

recommended that you configure the WAN connection using a single computer making

sure that both the computer and the Router are not connected to the LAN. Once the WAN

connection is functioning properly, you may continue to make changes to Router

configuration including IP settings and DHCP setup. This chapter is concerned with

using your computer to configure the WAN connection. The following chapter describes

the various menus used to configure and monitor the Router including how to change IP

settings and DHCP server setup.

3.2 Preparations before Login ROUTER

Before accessing the ROUTER, make sure that the communications between the PC and

the ROUTER are normal. Check the communications as follows:

Configure the IP address of the PC as 192.168.1.X (2~254), net mask as 255. 255.255.0,

gateway address as 192. 168.1.1 (for customized version, configure them according to the

actual version).

Use “arp –a” under Dos to check if the PC can read out the MAC address of the

ROUTER.

Ping the management IP address (192.168.1.1 by default) of the ROUTER.

If the PC can read out the MAC address of the ROUTER and can ping through the

management IP address of the ROUTER, that means the communications of the PC and

the ROUTER are normal.

Note that when you manage the ROUTER through WEB, you must keep the ROUTER

power on, otherwise you may damage the ROUTER.

3.3 Logging on the ROUTER

Open IE or Netscape Web browser, and input “http://192.168.1.1” (ROUTER default IP

address).

Connect to the ROUTER. The ROUTER will require a username and a password.

The default super username and password are “admin” and “admin”.

The default common username and password are “user” and “user”.

Download from Www.Somanuals.com. All Manuals Search And Download.

After logging in the ROUTER by a super username, you can query, configure, and

modify all configurations of the ROUTER; and you can diagnose the ROUTER system

too.

You need to reboot the ROUTER to enable your modification or configuration effective

sometimes, e.g. you modified the PVC configuration; some modification can take

effective at once without the ROUTER being rebooted, such as adding a static route. See

detailed descriptions below.

3.4 System Status

Click “Device Info” to enter the system information interface. At the left are seven

options: Summary, WAN, Statistics, Route, DHCP, and ARP.

3.4.1 Summary

Click “Device Info” to show the following interface.

Download from Www.Somanuals.com. All Manuals Search And Download.

This interface contains the following information:

Board ID:

Software Version:

Bootloader (CFE) Version:

Upstream Line Rate/Downstream Line Rate

LAN IP Address: The management IP address

Default Gateway: No gateway in a pure bridging mode; under other modes such as

PPPOE/PPPOA, it is the address of the uplink equipment.

DNS Server address: Obtained from the uplink equipment in PPPOE/PPPOA mode; No

DNS Server address in a pure bridging mode; or input them manually.

3.4.2 WAN

Click “WAN” to show the following interface. You can see these information: VPI/VCI,

Con. ID, Category, Service, Interface, Protocol, IGMP, QoS, Status, and WAN IP

Address.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.4.3 Statistics -- LAN

Click “Statistics”-->”LAN” to show the following interface. You can query information

on packets received at the Ethernet, USB and Wireless interfaces. Click “Reset

Statistics” to return the values to zero and recount them.

3.4.4 Statistics -- WAN

Click “Statistics”-->”WAN” to show the following interface. You can query information

on packets received at the WAN interfaces. Click “Reset Statistics” to return the values

to zero and recount them.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.4.5 Statistics -- ATM

Click “Statistics”-->”ATM” to show the following interface. You can query information

on packets received at the ATM interfaces. Click “Reset” to return the values to zero and

recount them.

3.4.6 Statistics -- ADSL

Click “Statistics”-->”ADSL” to show the following interface.

If the DSL line is activated, the following window will show.

Download from Www.Somanuals.com. All Manuals Search And Download.

You will see the following information pertinent to the ADSL line in the page:

Mode: G.DMT/G.LITE/T1.413/ADSL 2+/ADSL 2/READSL2

Line Coding: Trallis on, etc.

Status: Link Down, No Defect, Training

Link Power State: L0, L1, L2

Rate (Kbps): Upstream Line Rate/Downstream Line Rate.

At the lower part of this interface, there is a “Reset Statistics” button. Click it to return

values to zero and recount.

Click “ADSL BER Test” to do a “Bit Error Rate” Test on the DSL line.

The Tested Time (sec) has the following choices: 1, 5, 10, 20, 60, 120, 180, 240, 300, and

360. Select a time and then click “Start”.

Note: If the error ratio reaches up to “e-5”, the user will not be able to access the Internet.

3.4.7 Route

Click “Routing Table”. If the system is in the default configuration, the routing table will

be as follows:

Download from Www.Somanuals.com. All Manuals Search And Download.

3.4.8 ARP

Click “ARP” to show the following interface. You can query the MAC and IP addresses

information of the equipment attached to the ROUTER.

3.4.9 DHCP

Click “DHCP” to show the following interface. You can query the IP addresses

assignment from the DHCP server.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5 Advanced Setup

Click “Advanced Setup” to enter the advanced system setup interface. By default, there

are two options at the left side of the interface: “WAN”, “LAN”, etc. See the following

interface.

If the ROUTER is configured to a routing mode, such as built-in PPPOE access, there

will be more options at the left: “LAN”, “WAN”, “NAT”, “Security”, “Routing”, “DNS”,

“DSL” and so on.

3.5.1 WAN

Click “WAN” to show the following interface. In this interface, you can modify and

configure the WAN interface.

Note: After PVC is deleted or modified, the system must be rebooted, or the modification

will not be effective.

Download from Www.Somanuals.com. All Manuals Search And Download.

Choose Add, Edit, or Remove to configure WAN interfaces.

Choose Save/Reboot to apply the changes and reboot the system.

Now we only show you how to add PVC.

3.5.1.1 Configure PPPoE

Click “Add” to add a certain piece of PVC. The following descriptions are given by an

example of adding “PVC 8/35” (PPPOE mode).

Click “Add” following “PVC 8/35”.

In this interface, you can modify VPI/VCI, service categories, and QoS.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM

network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known

protocols).

Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime

VBR/Realtime VBR.

Enable Quality Of Service: enable/disable.

In this example, PVC 8/35 is required to modify, so service category and QoS will

remain default values. In actual applications, you can modify them depending on your

practices.

After proper modifications, click “Next” to show the following interface.

In this interface, you can modify Internet Connection Type and Encapsulation Type.

Change the connection type of PVC 8/35 to “PPP over ATM (PPPoE)”.

Select “PPP over ATM (PPPoE)”, and “LLC/SNAP-BRIDGING” (depending on the

uplink equipment, generally “LLC/SNAP-BRIDGING”) as “Encapsulation Mode”.

Download from Www.Somanuals.com. All Manuals Search And Download.

PPP Username: the correct user name that your ISP has provided to you.

PPP Password: the correct password that your ISP has provided to you.

PPPoE Service Name: If your ISP provided it to you, please input it. Unless

don’t input anything.

Authentication Method: AUTO, PAP, CHAP, MSCHAP. Usually select AUTO

will be OK.

Dial on demand (with idle timeout timer): If enable it, you need to input the

idle timeout time. Within the preset minutes, if the ROUTER doesn’t detect the

flow of the user continuously, the ROUTER will automatically disconnect the

PPPOE connection. Once it detects the flow (like access to a webpage), the

ROUTER will restart the PPPOE dial up.

If disable it, the ROUTER will perform PPPOE dial-up all the time. Unless the

ROUTER is powered off and DSLAM or uplink equipment are abnormal, the

PPPOE connection will not broken.

PPP IP extension: After “PPP IP extension” is enabled, the WAN IP address

obtained by the ROUTER through built-in dial-up can be directly assigned to the

PC being attached with the ROUTER (at this time, the ROUTER has only one

PC). From the view of the PC user, this is even with that the PC dials up to obtain

an IP address. But actually, the dial-up is done by the ROUTER.

If disable it, the ROUTER obtain the WAN IP address itself.

Use Static IP Address: If disabled it, the ROUTER through PPPOE dial-up, to

obtain an IP address assigned by uplink equipment such as BAS.

If enable it, the ROUTER use this IP as the WAN IP address.

After input the PPP Username and PPP Password, click “Next” to show the following

interface.

In this interface, you can modify the Service name and enable/disable the IGMP

Download from Www.Somanuals.com. All Manuals Search And Download.

Multicast, WAN Service.

IGMP Multicast: IGMP proxy. For example, if you need PPPoE mode support

IPTV, please enable it.

WAN Service: Please enable it, unless you don’t need to active the PVC.

Click “Next” to show the following interface.

In this interface, it shows the all configuration. You can see some default values: NAT

enable, Firewall enable.

Click “Save” to save these settings. And you can click “Back” to make any

Download from Www.Somanuals.com. All Manuals Search And Download.

modifications.

NOTE: You need to reboot to activate this WAN interface and further configure services

over this interface.

3.5.1.2 Configure PPPoA

Click “Add” to add a certain piece of PVC. The following descriptions are given by an

example of adding “PVC 8/35” (PPPOA mode).

Click “Add” following “PVC 8/35”.

In this interface, you can modify VPI/VCI, service categories and QoS.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM

network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known

protocols).

Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime

VBR/Realtime VBR.

Enable Quality Of Service: enable/disable.

In this example, PVC 8/35 is required to modify, so service category and QoS will

remain default values. In actual applications, you can modify them depending on

your practices.

After proper modifications, click “Next” to show the following interface.

In this interface, you can modify Internet Connection Type and Encapsulation Type.

Change the connection type of PVC 8/35 to “PPP over ATM (PPPoA)”.

Select “PPP over ATM (PPPoA)”, and “VC/MUX” (depending on the uplink equipment,

generally “VC/MUX”) as “Encapsulation Mode”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Next”. In this interface, you can modify the PPP Username, PPP Password,

Authentication Method and so on.

PPP Username: the correct user name that your ISP has provided to you.

PPP Password: the correct password that your ISP has provided to you.

Authentication Method: AUTO, PAP, CHAP, MSCHAP. Usually select AUTO

will be OK.

Dial on demand (with idle timeout timer): If enable it, you need to input the

idle timeout time. Within the preset minutes, if the ROUTER doesn’t detect the

flow of the user continuously, the ROUTER will automatically disconnect the

PPPOA connection. Once it detects the flow (like access to a webpage), the

ROUTER will restart the PPPOA dial up.

If disable it, the ROUTER will perform PPPOA dial-up all the time. Unless the

ROUTER is powered off and DSLAM or uplink equipment is abnormal, the

PPPOA connection will not broken.

PPP IP extension: After “PPP IP extension” is enabled, the WAN IP address

obtained by the ROUTER through built-in dial-up can be directly assigned to the

PC being attached with the ROUTER (at this time, the ROUTER has only one

PC). From the view of the PC user, this is even with that the PC dials up to obtain

an IP address. But actually, the dial-up is done by the ROUTER.

If disable it, the ROUTER obtain the WAN IP address itself.

Use Static IP Address: If disabled it, the ROUTER through PPPOA dial-up, to

obtain an IP address assigned by uplink equipment such as BAS.

If enable it, the ROUTER use this IP as the WAN IP address.

After input the PPP Username and PPP Password, click “Next” to show the following

interface.

Download from Www.Somanuals.com. All Manuals Search And Download.

In this interface, you can modify the Service name and enable/disable the IGMP

Multicast, WAN Service.

IGMP Multicast: IGMP proxy. For example, if you need PPPoA mode support

IPTV, please enable it.

WAN Service: Please enable it, unless you don’t need to active the PVC.

Click “Next”. In this interface, it shows the all configuration. You can see some default

values: NAT enable, Firewall enable.

Click “Save” to save these settings. And you can click “Back” to make any

modifications.

NOTE: You need to reboot to activate this WAN interface and further configure services

over this interface.

3.4.1.3 Configure MER

Click “Add” to add a certain piece of PVC. The following descriptions are given by an

example of adding “PVC 8/35” (MER mode).

Click “Add” following “PVC 8/35”.

In this interface, you can modify VPI/VCI, service categories and QoS.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM

network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known

protocols).

Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime

VBR/Realtime VBR.

Enable Quality of Service: enable/disable.

In this example, PVC 8/35 is required to modify, so service category and QoS will

remain default values. In actual applications, you can modify them depending on

your practices.

After proper modifications, click “Next” to show the following interface.

In this interface, you can modify Internet Connection Type and Encapsulation Type.

Change the connection type of PVC 8/35 to “MAC Encapsulation Routing (MER)”.

Select “MAC Encapsulation Routing (MER)”, and “LLC/SNAP-BRIDGING”

(depending on the uplink equipment, generally “LLC/SNAP-BRIDGING”) as

“Encapsulation Mode”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Next”. In this interface, you can modify the WAN IP address, Default Gateway

and DNS Server settings.

Obtain an IP address automatically: The ROUTER will obtain a (WAN) IP

address automatically and at this time it will enable DHCP Client functions. The

WAN IP address is obtained from the uplink equipment like BAS and the uplink

equipment is required to enable the DHCP Server functions.

Use the following IP address: If you want to input the WAN ip address by

yourself. Check this entry and then input related data in the field.

WAN IP Address: Input the IP address of the WAN interface provided by your

ISP.

WAN Subnet Mask: Input the subnet mask concerned to the IP address of the

WAN interface provided by your ISP.

Obtain Default Gateway automatically: To obtain the IP address of the default

gateway assigned by the uplink equipment such as BAS.

Use the following Default Gateway: If you want to input the IP address of the

default gateway by yourself, click this entry and then input related data in the

fields.

Use IP Address: Input the gateway of the WAN interface provided by your ISP.

Use WAN Interface: As to BAS equipment, it is the IP address of the downlink

interface.

Obtain DNS server address automatically: To obtain the IP address of the

DNS server assigned by the uplink equipment such as BAS.

Use the following DNS server address: If you want to input the IP address of

the DNS server by yourself, click this entry and then input related data in the

fields.

Primary DNS server: Input the IP address of the primary DNS server here.

Secondary DNS server: Input the IP address of the secondary DNS server

provided by your ISP here.

Download from Www.Somanuals.com. All Manuals Search And Download.

After correctly modifications, click “Next” to show the following interface.

In this interface, you can modify the Service name and enable/disable the NAT, Firewall,

IGMP Multicast, WAN Service.

Enable NAT: Select it to enable the NAT functions of the ROUTER. If you are

not to enable NAT and intend the user of the ROUTER to access the Internet

normally, you must add a route on the uplink equipment; otherwise the access to

the Internet will fail. Normally, it is required to enable NAT.

Enable Firewall: enable/disable IP filtering.

IGMP Multicast: IGMP proxy. For example, if you need MER mode support

IPTV, please enable it.

WAN Service: Please enable it, unless you don’t need to active the PVC.

Click “Next”. In this interface, it shows the all configuration.

Click “Save” to save these setting. And you can click “Back” to make any modifications.

NOTE: You need to reboot to activate this WAN interface and further configure services

over this interface.

3.5.1.4 Configure IPoA

Click “Add” to add a certain piece of PVC. The following descriptions are given by an

example of adding “PVC 8/35” (IPoA mode).

Click “Add” following “PVC 8/35”.

In this interface, you can modify VPI/VCI, service categories and QoS.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM

network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known

protocols).

Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime

VBR/Realtime VBR.

Enable Quality Of Service: enable/disable.

In this example, PVC 8/35 is required to modify, so service category and QoS will

remain default values. In actual applications, you can modify them depending on

your practices.

After proper modifications, click “Next” to show the following interface.

In this interface, you can modify Internet Connection Type and Encapsulation Type.

Change the connection type of PVC 8/35 to “IP over ATM (IPoA)”.

Select “IP over ATM (IPoA)”, and “LLC/SNAP-ROUTING” (depending on the uplink

equipment, generally “LLC/SNAP-ROUTING”) as “Encapsulation Mode”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Next”. In this interface, you can modify the WAN IP, Default Gateway and DNS

Server settings.

WAN IP Address: Input the IP address of the WAN interface provided by your

ISP.

WAN Subnet Mask: Input the subnet mask concerned to the IP address of the

WAN interface provided by your ISP.

Obtain Default Gateway automatically: To obtain the IP address of the default

gateway assigned by the uplink equipment such as BAS.

Use the following Default Gateway: If you want to input the IP address of the

default gateway by yourself, click this entry and then input related data in the

fields.

Otherwise to obtain the IP address of the default gateway assigned by the uplink

equipment such as BAS.

Use IP Address: Input the gateway of the WAN interface provided by your ISP.

Use WAN Interface: As to BAS equipment, it is the IP address of the downlink

interface.

Obtain DNS server address automatically: To obtain the IP address of the

DNS server assigned by the uplink equipment such as BAS.

Use the following DNS server address: If you want to input the IP address of

the DNS server by yourself, click this entry and then input related data in the

fields.

Primary DNS server: Input the IP address of the primary DNS server here.

Secondary DNS server: Input the IP address of the secondary DNS server

provided by your ISP here.

After correctly modifications, click “Next” to show the following interface.

In this interface, you can modify the Service name and enable/disable the NAT, Firewall,

Download from Www.Somanuals.com. All Manuals Search And Download.

IGMP Multicast, WAN Service.

Enable NAT: Select it to enable the NAT functions of the ROUTER. If you are

not to enable NAT and intend the user of the ROUTER to access the Internet

normally, you must add a route on the uplink equipment; otherwise the access to

the Internet will fail. Normally, it is required to enable NAT.

Enable Firewall: enable/disable IP filtering.

IGMP Multicast: IGMP proxy. For example, if you need IPoA mode support

IPTV, please enable it.

WAN Service: Please enable it, unless you don’t need to active the PVC.

Click “Next”. In this interface, it shows the all configuration.

Click “Save” to save these settings. And you can click “Back” to make any

modifications.

NOTE: You need to reboot to activate this WAN interface and further configure services

over this interface.

3.5.1.5 Configure Bridge

Click “Add” to add a certain piece of PVC. The following descriptions are given by an

example of adding “PVC 8/35” (IPoA mode).

Click “Add” following “PVC 8/35”.

In this interface, you can modify VPI/VCI, service categories and QoS.

VPI (Virtual Path Identifier): The virtual path between two points in an ATM

network, and its valid value is from 0 to 255.

VCI (Virtual Channel Identifier): The virtual channel between two points in an

ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known

protocols).

Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime

VBR/Realtime VBR.

Enable Quality Of Service: enable/disable.

In this example, PVC 8/35 is required to modify, so service category and QoS will

remain default values. In actual applications, you can modify them depending on

your practices.

After proper modifications, click “Next” to show the following interface.

In this interface, you can modify Internet Connection Type and Encapsulation Type.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Next”. In this interface, you can modify the Service name.

WAN Service: Please enable it, unless you don’t need to active the PVC.

Click “Next”. In this interface, it shows the all configuration.

Click “Save” to save these settings. And you can click “Back” to make any

modifications.

NOTE: You need to reboot to activate this WAN interface and further configure services

over this interface.

3.5.2 LAN

In this interface, you can modify and configure “IP Address” and “DHCP Server”.

If bridge mode only, the interface as below:

Download from Www.Somanuals.com. All Manuals Search And Download.

Enable IGMP Snooping: It used to Bridge mode.

3.5.3 NAT

Click “NAT” to show the following interface. Under “NAT”, there are four network

share modes: “virtual Server”, “port triggering”, and “DMZ Host”.

3.5.3.1 NAT -- Virtual Servers Setup

In this interface, you can query any preset virtual server, delete an exiting virtual server,

and add a new virtual server. By default, the system is not configured with a virtual

server.

Download from Www.Somanuals.com. All Manuals Search And Download.

When NAT is enabled on the ROUTER, the whole LAN that the ROUTER is attached

will appear as a single machine on the Internet. Normally, external users are not allowed

to visit the PCs in the whole LAN to which the ROUTER is attached. But under some

circumstances, we hope that some PCs will be open and allow anyone to access them. At

this time, we can use the virtual server to perform this. After the virtual server is

configured, when the packets that the ROUTER receives request to enter the local server,

the ROUTER will identify the service categories according to the “port” number

encapsulated within the packets. For example, “port 21” stands fro FTP service. Now, we

will explain it with an example. The topology is as follows:

The WAN IP Address of the ROUTER is 203.70.212.52. The PC1 192.168.1.10 attached

to it is a WEB Server; PC2 192.168.1.20 is a FTP server. These two servers are intended

to be open to external users. The detailed configuration steps are as follows:

Click “Add” to show the following interface.

Download from Www.Somanuals.com. All Manuals Search And Download.

Service Name: Select one service item, such as Mail (SMTP), Mail (POP3), Web Server

(HTTP), FTP Server, and TFTP, from the list. The information about the selected item

will appear in the box below.

Customized server: Enter a new service name to establish a specified user service

category.

Server IP address: When you intend to assign a specified address to the virtual server,

enter the server IP address here.

External port start/end: When you have already selected one service, the port number

will appear automatically. You can change it as you need.

Protocol: Choose proper protocols for your services.

Internal port start/end: When you have already selected one service, the port number

will appear automatically. You can change it as you need.

PC1 (192.168.1.10): WEB Server

Note: The default port number of the external port and the internal port is 80. In this

example, it is changed to 8060.

After proper modifications, click “Save/Apply”. (This configuration will take effective at

once.)

PC2 (192.168.1.20): FTP server

After proper modifications, click “Apply” (This configuration will take effective at once).

If you want to delete a certain virtual server, you can choose this virtual server and click

“Remove” to delete it.

After the virtual server is already configured, any user from the Internet can access to

your virtual server. They must use the Internet IP address (the IP address provided by

your ISP), for example:

Http://203.70.212.52:8060 and Ftp://203.70.212.52

The access will be led to the local server which possesses an private IP address, that is,

according to the service categories (TCP/UDP port numbers), the ROUTER will lead the

external service requests to an appropriate server (located at another internal IP address).

Suggestion: Use a fixed WAN IP address. In this way, it is more convenient than an

dynamic IP address.

3.5.3.2 NAT -- Port Triggering Setup

Click “Port Triggering” to pop up an interface as below. In this interface, you can

configure Port Triggering.

Some applications require that specific ports in the Router's firewall be opened for access

by the remote parties. Port Trigger dynamically opens up the 'Open Ports' in the firewall

when an application on the LAN initiates a TCP/UDP connection to a remote party using

the 'Triggering Ports'. The Router allows the remote party from the WAN side to

establish new connections back to the application on the LAN side using the 'Open Ports'.

Download from Www.Somanuals.com. All Manuals Search And Download.

A maximum 32 entries can be configured.

3.5.3.3 NAT -- DMZ Host

Click “DMZ Host” to pop up an interface as below. In this interface, you can configure

DMZ services.

Demilitarized Zone (DMZ) is a technology that enables the ROUTER to forward all input

packets onto a server specified internally. It can make a PC in a LAN completely exposed

to all users in the Internet, and it also can allow a specified IP address and other Internet

users or servers to communicate mutually without any limit.

Permitting most of applications to run on the specified IP address.

Specifying an IP address to receive all known connections and documents.

Enter “DMZ Host IP Address” and click “Save/Apply” to activate the DMZ host.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5.4 Security

Click “Security” -->” IP Filtering” to show the following interface. By default, the

firewall is enabled. The firewall is used to block document transmissions between the

Internet and your PC. It serves as a safety guard and only permits authorized documents

to be sent into the LAN.

Note: If the router configured bridge mode only, the IP Filtering will disabled and the IP

filtering interface will disappear.

And if the router configured no Bridge mode PVC, the MAC Filtering will disabled and

the MAC Filtering interface will disappear.

3.5.4.1 Outgoing IP Filtering Setup

Click “Security”-->” IP Filtering”-->” Outgoing” to show the following interface.

By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be

BLOCKED by setting up filters.

Click “Add” to enter the related interface defining the IP filtering rule as follows.

The screen allows you to create a filter rule to identify outgoing IP traffic by specifying a

new filter name and at least one condition below. All of the specified conditions in this

filter rule must be satisfied for the rule to take effect. Click 'Save/Apply' to save and

activate the filter.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5.4.2 Incoming IP Filtering Setup

Click “Security”-->” IP Filtering”-->” Incoming” to show the following interface.

By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled.

However, some IP traffic can be ACCEPTED by setting up filters.

The screen allows you to create a filter rule to identify incoming IP traffic by specifying a

new filter name and at least one condition below. All of the specified conditions in this

filter rule must be satisfied for the rule to take effect. Click 'Save/Apply' to save and

activate the filter.

And you must select at least one or multiple WAN interfaces to apply this rule.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5.4.3 Parental Control

Click “Security”-->”Parental Control” to show the following interface.

Click “add” to show the interface.

This page adds time of day restriction to a special LAN device connected to the Router.

The 'Browser's MAC Address' automatically displays the MAC address of the LAN

device where the browser is running. To restrict other LAN device, click the "Other

MAC Address" button and enter the MAC address of the other LAN device. To find out

the MAC address of a Windows based PC, go to command window and type "ipconfig

/all".

3.5.5 Routing

Click “Routing”.

3.5.5.1 Routing – Default Gateway

In this interface, you can modify the Default Gateway settings.

If Enable Automatic Assigned Default Gateway checkbox is selected, this router will

accept the first received default gateway assignment from one of the PPPoA, PPPoE or

MER/DHCP enabled PVC(s). If the checkbox is not selected, enter the static default

gateway AND/OR a WAN interface. Click 'Save/Apply' button to save it.

NOTE: If changing the Automatic Assigned Default Gateway from unselected to selected,

you must reboot the router to get the automatic assigned default gateway.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “ENABLE Automatic Assigned Default Gateway” box to show the interface.

3.5.5.2 Routing – Static Route

In this interface, you can modify the Static Route settings.

Click “Static Route” to pop up an interface as shown in Fig. 3.5-47. In this interface, you

can query the preset static routes, delete an existing static route, or add a new static route.

By default, the system has no static route information.

Destination: The IP address where packets will go to.

Netmask: The subnet mask of the destination IP address.

Gateway:

Interface:

The gateway that the packets will pass by during transmission.

The interface that the packets pass through on the ROUTER.

Click “Add” to show the following interface.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.5.6 DNS

3.5.6.1 DNS Server

In this interface, you can modify the DNS server settings.

If 'Enable Automatic Assigned DNS' checkbox is selected, this router will accept the first

received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s)

during the connection establishment.

If the checkbox is not selected, enter the primary and optional secondary DNS server IP

addresses. The interface is below.

Click 'Save' button to save the new configuration.

NOTE: You must reboot the router to make the new configuration effective.

3.5.6.2 Dynamic DNS

In this interface, you can modify the Dynamic DNS settings.

The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname

in any of the many domains, allowing your DSL router to be more easily accessed from

various locations on the Internet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Add” to add dynamic DDNS.

3.5.7 DSL

In this interface, you can modify the DSL settings.

Select one you need. But the default setting check G.dmt / G.lite / T1.413 / ADSL2 /

ADSL2+ / Bitswap / SRA. The ROUTER will negotiate the modulation mode with the

DSLAM.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.6 Diagnostics

Click “Diagnostics” to show the interface.

Your router is capable of testing your DSL connection. The individual tests are listed

below. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this

page to make sure the fail status is consistent. If the test continues to fail, click "Help"

and follow the troubleshooting procedures.

3.7 Management

3.7.1 Settings

3.7.1.1 Settings Backup

Click the “Backup Settings”, backup the DSL router configurations.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.7.1.2 Settings Update

Click the “Browsing...” button, select the correct update configure settings file. Then

click the “Update Settings” to update the Router settings.

3.7.1.3 Settings Restore Default

Download from Www.Somanuals.com. All Manuals Search And Download.

Click “Restore Default Settings” to restore DSL router settings to the factory defaults.

3.7.2 System Log

Click “System Log” to show the following interface. The system log dialog allows you to

view the system log and configure the system log options.

Click “Configure System Log” to show the following interface. You can enable or

disable the system log and then select the log level, display level and mode, and

click “Apply” to end your configurations.

Both the log level and display level have eight choices. The default log level is

“Debugging” and the default display level is “Error”.

The mode options are “Local”, “Remote”, and “Both”. The default one is “Local”.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you select “Remote” or “Both”, all events will be transmitted to the specified

UDP port of the specified log server.

After operations under “Configure System Log”, click “View System Log” to

query the system logs. In this example, the “View System Log” is a system

default one.

Note: The log and display of the system events are above the set level. If you

intend to record all information, you need to set the levels as “Debugging”.

Click “Refresh” to refresh the system event logs or “Close” to exit from this

interface.

3.7.3 Internet Time

Click the “Internet Time”, the interface show you. In this page, the ROUTER can

synchronize with Internet time servers.

After enable “Automatically synchronize with Internet time servers”, the interface shows

below. Enter proper configurations, and then click “Save/Apply”.

3.7.4 Access Control

3.7.4.1 Access Control – Services

Click “Access Control”-->”Services” to show the following interface. In the interface,

Download from Www.Somanuals.com. All Manuals Search And Download.

you can enable/disable the HTTP, ICMP, SNMP, TELNET and TFTP services. And the

LAN side and WAN side can have different configurations.

3.7.4.2 Access Control -- IP Addresses

Click “Access Control”-->”IP Addresses” to show the following interface.

If enabled, permits access to local management services from IP addresses contained in

the Access Control List.

If the Access Control mode is disabled, the system will not validate IP addresses for

incoming packets. The services are the system applications listed in the Service Control

List.

Click “add” to show the following interface. In the interface input the IP address of the

Download from Www.Somanuals.com. All Manuals Search And Download.

management station permitted to access the local management services, and click

“Save/Apply”.

3.7.4.3 Access Control – Passwords

Click “Access Control”-->”Passwords” to show the following interface. In the interface,

you can modify the accounts passwords.

3.7.5 Update Software

Click “Update Firmware” to show the following interface. In this interface, you can

update the ROUTER Firmware. Click the “Browse...” button to find the right version

file and press “Update Firmware” to do the update.

NOTE: Do not turn off your ROUTER during firmware updates. When the update is

finished, the ROUTER will reboot automatically. Do not turn off your ROUTER either

Download from Www.Somanuals.com. All Manuals Search And Download.

before the reboot is over. You must guarantee the update software is right and accurate.

It is strictly forbidden to use other software for updates.

After update software, it is suggested to restore the ROUTER to the factory defaults

and configure it again.

3.7.6 Save/Reboot

Click “Save/Reboot” to show the following interface. Click the “Save/Reboot” button to

save and reboot the router.

4. Networking Topology

Before configuring the ROUTER, you must clearly determine that the ROUTER is used

for Bridging mode or Routing mode. This chapter will introduce some applications. And

see Chapter 3 Introductions to WEB Configuration Management for detailed

configurations.

4.1 PPP over ATM (PPPoA) Mode

Download from Www.Somanuals.com. All Manuals Search And Download.

Descriptions

In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the

access mode is the built-in PPPOA+NAT. The encapsulation of the BRAS downlink port

is PPP OVER ATM, the authentication is AUTO, the IP address is 10.28.106.200, the IP

Pool is 10.28.106.*, and the IP address of uplink port is 10.61.92.157. The IP of the

WAN port on the ROUTER is assigned by BRAS through the built-in PPPOA dial-up

dynamically. The PC that the ROUTER is attached is assigned with a private IP address

(within the same segment with the management IP of the ROUTER). The NAT functions

of the ROUTER will be enabled and the private PC address will be translated to the

public address 10.28.106.* (2 ~ 254) assigned by BRAS dynamically for accessing ISP.

The IP address of the PC can be fixed (as in this example) or assigned through DHCP

Server of the ROUTER. If it is assigned by DHCP Server, the DHCP functions of the

ROUTER must be enabled. The IP address of the DHCP address pool is 192.168.1.*

(2~254). The functions are enabled by default and at the same time the PC is configured

to obtain IP and DNS addresses dynamically.

Setting:

1. Activate your browser and input “192.168.1.1” in the address column to login the

ROUTER.

2. Click “Advanced Setup” -> “WAN”, then click “add”.

3. In the “ATM PVC Configuration” interface configure VPI/VCI as 8/35 and then

click “Next”.

4. In the “Connection Type” interface, select “PPP over ATM (PPPoA)” and “VC

MUX” as the encapsulation, and then click “Next”.

5. In the “PPP User name and Password” interface, enter the user name and password

provided by your ISP. And then click “Next”.

6. In the “Enable IGMP Multicast and WAN Service” interface, keep the default

configuration unchanged and then click “Next”.

7. Check the network configurations and make sure that all settings agree with the data

provided by your ISP, and then click “Save”.

8. Click “Save/Reboot” to apply the changes and reboot the system.

Download from Www.Somanuals.com. All Manuals Search And Download.

You can also modify the PVC 8/35. If you need to modify the LAN IP address and

DHCP server information, you can do it in “LAN” in “Advanced Setup”.

After the dial-up is successful, the IP address that the ROUTER obtains at the WAN-side

port ppp_8_35_1. Query “Device Info” “Route” and the route table is as follows:

Note: After the built-in PPPOA dial-up is successful, the created WAN-side port is

ppp_8_35_1.

4.2 PPP over Ethernet (PPPoE) Mode

Descriptions

In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the

access mode is the built-in PPPOE+NAT. The encapsulation of the BRAS downlink port

is PPP OVER ETHERNET, the authentication is AUTO, the IP address is 10.28.106.200,

the IP Pool is 10.28.106.*, and the IP address of uplink port is 10.61.92.157. The IP of

the WAN port on the ROUTER is assigned by BRAS through the built-in PPPOE dial-up