1. Specification
LCD panel type
12.1” TFT (12.1” Diagonal)
Displayable resolution
Pixel dimension
WXGA 1280 x 800 maximum
0.204 mm horizontal x 0.204 mm vertical
LCD display color
OSD control
262,144 Colors
Exit, Positioning(Horizontal, Vertical)
Image Settings(Auto Adjust, Pixel Clock, Phase)
Color Setting(Auto Color, 9300K Preset, 6500K Preset, User Preset)
OSD Setting(Horizontal Position, Vertical Position, OSD Hold Time,
OSD Lock),
Language(English, Español, Français, Deutsch)
Factory Reset
Manual control buttons
Viewing angle
POWER , ＋ , － ,SELECT , MENU
Horizontal: ± 89, Vertical: ± 89. (CR＞10)
Contrast ratio
Brightness
500:1 (Typ.)
300 cd/m2
Response time
30 ms, Tr＋Td (Typ.)
Active display area
AC/DC adapter
261.12 mm (H) x163.20mm (V)
Input: AC 100 ~ 240V, 50 ~ 60 Hz
Output: +12 Vdc / 3.0A
Input signal
Video: Analog 0.7 Vp‐p. 75 ohms
Sync. : TTL Level, Positive/ Negative, Separate Sync.
DVI : REV1.0 Digital Single T.M.D.S.
15 Pin D‐Sub. , 24Pin DVI‐D , USB B‐type , 2.5ψ DC‐Jack
Input connector
Touch screen
3M Cap. (SCT3250 98‐0003‐3205‐0 & EXII‐7730HC)
MSR (option)
ID‐TECH (CPR60029 , USB Interface, 3 Track)
Power management
Regulation
Yes
cUL, FCC, CE
Dimensions ( W x D x H )
Weight
341 mm x 280 mm x 95 mm.
220 g. (LCD Module only)
2.1 Kg. (unit)
Accessory
VGA cable, DVI‐D cable, USB cable, AC/DC adapter, power cord.
Temperature
Operation : 0 ~ 40°C
Storage : ‐20 ~ 60°C
LT1201 User Manual (020-1080-00 Rev. A)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LT1201 User Manual (020-1080-00 Rev. A)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Important Servicing Safety Precautions
Prior to using this manual, please ensure that you have carefully followed all the procedures outlined in the
user manual for this product. Read all of these instructions. Save these instructions for later use.
Follow all warnings and instructions marked on the product.
Do not use this product near water.
•
•
•
•
This display should be installed on a solid horizontal base.
When cleaning, use only a neutral detergent cleaner with a soft damp cloth. Do not spray with liquid
or aerosol cleaners.
Do not expose this display to direct sunlight or heat. Hot air may cause damage to the cabinet and
other parts.
•
•
Adequate ventilation must be maintained to ensure reliable and continued operation and to protect
the display from overheating. Do not block ventilation slots and openings with objects or install the
display in a place where ventilation may be hindered.
Do not install this display near a motor or transformer where strong magnetism is generated.
Images on the display will become distorted and the color irregular.
•
Do not allow metal pieces or objects of any kind fall into the display from ventilation holes.
•
•
Slots and openings in the cabinet and the back or bottom are provided for ventilation, to ensure
reliable operation of the product and to protect it from overheating, those openings muse not be
blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should never be placed near or over a radiator or heat register.
This product should not be placed in a built‐in installation unless proper ventilation is provided.
LT1201 User Manual (020-1080-00 Rev. A)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Location of Controls
1) POWER SWITCH
Pressing the power key will turn the monitor on. Pressing it again will turn it off.
2) POWER INDICATOR (green)
The LED indicator lamp is green; the unit is in normal operating mode.
The LED indicator lamp will change to orange when it is power‐saving mode.
3) ＋ : ( RIGHT )
Auto Adjust in Progress
to scroll down the menu
to increase value of selected item
4) － : ( LEFT )
to adjust the brightness and contrast on the monitor
to scroll up in the menu
to decrease value of selected item
5) SELECT:
To confirm the current selection. It’s also used for going back to previous menu or
sub‐menu, and the changed data will be saved to memory.
6) MENU:
Enters or exits the OSD (On Screen Display) menus. It also exits from the submenu back
to the previous menu. This type of cancellation will not save the previous changes.
4. Hot‐key define
With signal input :
1) [＋] key ==> Auto adjust in progress
2) [－] key ==> Adjust Brightness and Contrast
3) [SELECT] key ==> change VGA and DVI input source
4) [＋] and [－] ==> key lock & key unlock, when push [＋] and [－] buttons simultaneously
5) [MENU] key ==> Factory mode, push and hold [MENU] key then power‐in
Without signal input:
6) [＋] and [－] ==> Burn‐in mode, when push and hold [＋] and [－] buttons simultaneously,
Then power‐in
LT1201 User Manual (020-1080-00 Rev. A)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Block Diagram
INTERFACE BOARD
COMPUTE
R
CN2
U4 MStar
TSUM5PNJ
U1(24C02)
(DB15)
SCALER
COMPUTE
R
X1
OSC
CN3
U3 (24C02)
(DVI)
CN5
30 PIN
LVDS CABLE
&
Flash
memory
U6
EEPROM
UH1
XH1
OSC
Backlight
control
HUB 2.0
GL850G
COMPUTE
R
SWITCH MODE
PH1
3.3V
5V
B-type
POWER SUPPLY
PH2
5PIN
PH3
5PIN
J1
JP1
8
FROM
A/D ADAPTOR
12V
Connector board
PWB-5818 (2)
JP1
SW BOARD
PWB-5818 (1)
MSR kit
C
Control board
EXII-7730HC
O
N
N
E
12.1” LCD
PANEL
C
T
3M Touch screen
LT1201 User Manual (020-1080-00 Rev. A)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Internal connector pin definition
WXGA I/F BOARD
J1: Key Switch for OSD Adjustment, Power Switch and Brightness Control Input Terminal
Pin No.
Symbol
Function
1
2
3
4
5
6
7
8
ADJUST / ‐
ADJUST / +
MENU
For OSD Adjustment
For OSD Adjustment
For OSD Adjustment
For OSD Adjustment
For POWER on/off
Normal Mode: Low
Save Mode : Low
Ground
SELECT
POWER
LED‐GRN
LED‐ORG
GND
PH2.PH3: Output Terminal for USB device unit
Pin No.
Cable Color
Function
1
2
3
4
5
Red
White
Green
Black
Drain wire
VBUS(5 Volts)
D‐
D+
Ground
Shield ground
PH1: USB B‐type Input Terminals
Pin No.
Cable Color
Function
1
2
3
4
Red
VBUS(5 Volts)
White
Green
Black
D‐
D+
Ground
CN2: VGA Signal Input Terminals
Pin No.
Symbol
Function
1
2
3
VGA R
VGA G
VGA B
RED Video Input Signal
GREEN Video Input Signal
BLUE Video Input Signal
4
NC
5
GND
GND
6
7
8
9
10
11
12
13
14
15
RED RETURN
GREEN RETURN
BLUE RETURN
5V DCC
VGA CONN
NC
GND for RED video signal
GND for GREEN video signal
GND for BLUE video signal
Support DDC +5V power
Detect VGA connector signal
VGA SDA
VGA HS
VGA VS
DDC data
Horizontal Sync. Signal
Vertical Sync. Signal
DDC clock
VGA SCL
LT1201 User Manual (020-1080-00 Rev. A)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CON3: DVI Signal Input Terminals
Pin NO.
1
Symbol
Dat2‐
Function
T.M.D.S Data2‐
T.M.D.S Data2+
T.M.D.S Data2/4 Shield
T.M.D.S Data4‐
T.M.D.S Data4+
DDC Clock
2
Dat2+
3
2/4 Shield
Dat4‐
4
5
Dat4+
6
DDC SCL
DDC SDA
VSYNC
Dat1‐
7
DDC Data
8
NC
9
T.M.D.S Data1‐
T.M.D.S Data1+
T.M.D.S Data1/3 Shield
T.M.D.S Data3‐
T.M.D.S Data3+
+5V Power
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
Dat1+
1/3 Shield
Dat3‐
Dat3+
+5V
SYNC GND
HPD
Ground
Hot Plug Detect
T.M.D.S Data0‐
T.M.D.S Data0+
T.M.D.S Data0/5 Shield
T.M.D.S Data5‐
T.M.D.S Data5+
T.M.D.S Clock Shield
T.M.D.S Clock+
T.M.D.S Clock‐
NC
Dat0‐
Dat0+
0/5 Shield
Dat5‐
Dat5+
CLK Shield
CLK+
CLK‐
Red
Green
Blue
NC
NC
HSYNC
RGB GND
NC
NC
LT1201 User Manual (020-1080-00 Rev. A)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CN5: Output Terminal for Panel Connector
Pin No.
1
Symbol
PANEL_VCC
PANEL_VCC
PANEL_VCC
LVDS_SET
GND
Function
3.3 Power supply
3.3 Power supply
3.3 Power supply
LVDS_SET
2
3
4
5
Ground
6
GND
Ground
7
8
RXE0‐
VDD_EDID
Receiver signal (‐)
VCC 3.3V
9
RXE0+
GND
Receiver signal (+)
Ground
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
RXE1‐
CLK_EDID
RXE1+
DATA_EDID
RXE2‐
Receiver signal (‐)
CLK_EDID
Receiver signal (+)
DATA_EDID
Receiver signal (‐)
Ground
Receiver signal (+)
Adjust back‐light
Clock signal (‐)
Black‐light on/off
Clock signal (+)
Ground
GND
RXE2+
VDIM
RXEC‐
BL ON
RXC+
GND
RXE3‐
Receiver signal (‐)
VCC 12V for back‐light device
Black‐light VCC 12V
25
26
27
28
29
30
RXE3+
Black‐light VCC 12V
GND
Black‐light VCC 12V
GND
Receiver signal (+)
VCC 12V for back‐light device
Ground
VCC 12V for back‐light device
Ground
Black‐light VCC 12V
VCC 12V for back‐light device
SW board
JP1: Output Terminal for OSD, Power and Brightness control.
Symbol
Function
1
2
3
4
5
6
7
8
POWER
LED‐GRN
LED‐ORG
ADJUST / +
ADJUST / ‐
SELECT
For POWER on/off
Normal Mode: Low
Save Mode: Low
For OSD Adjustment
For OSD Adjustment
For OSD Adjustment
For OSD Adjustment
Ground
MENU
GND
LT1201 User Manual (020-1080-00 Rev. A)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Cable pin definition
Switch board cable: WIRE 28AWG
Connection relationship
P1 (PHR‐8)
P2 (ZHR‐8)
WIRE COLOR
Pin No.
Pin No.
1
2
BLACK
BROWN
5
4
3
4
5
6
7
8
RED
7
6
1
3
2
8
ORANGE
YELLOW
GREEN
BLUE
PURPLE
Int. C/B cable for 3M touch: WIRE 28AWG, Shielding cable
Connection relationship
P1 (PHR‐5)
P2 (ZHR‐5)
WIRE COLOR
Pin No.
Pin No.
1
2
BLACK
BROWN
1
2
3
4
5
RED
ORANGE
DRAIN
3
4
5
LT1201 User Manual (020-1080-00 Rev. A)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Int. MSR extend cable: WIRE 28AWG, Shielding cable
Connection relationship
P1 (PHR-5)
P2 (PHR-5)
Pin No.
WIRE COLOR
Pin No.
1
2
BLACK
BROWN
1
2
3
4
RED
ORANGE
3
4
5
DRAIN
5
LVDS cable: WIRE UL10064 34# OD: 0.35mm
CN1 housing: JAE FI-JT40C-R3000 CNC housing: ACS 87219-3000
Connection relationship
CN1
WIRE COLOR
CN2
1
3
4
5
6
BLACK
BROWN
RED
ORANGE
YELLOW
5
1
2
3
8
8
9
BLACK
WHITE
BROWN
WHITE
RED
WHITE
ORANGE
WHITE
YELLOW
WHITE
GREEN
BLUE
PURPLE
GRAY
WHITE
BLACK
BROWN
RED
12
14
7
twist
twist
twist
twist
twist
twist
twist
twist
twist
twist
13
14
16
17
19
20
22
23
25
26
29
34
35
36
37
40
9
11
13
15
17
19
21
18
20
22
24
26
28
30
6
10、11、15
18、21、24
28、30、31、32
2、7、12
10、16
GND
NC
27、29
4、23、25
LT1201 User Manual (020-1080-00 Rev. A)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
27、33、38、39
LT1201 User Manual (020-1080-00 Rev. A)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Trouble Shooting
Does
picture
YES
display?
NO
A dark
picture or a
picture full
of colorfully
vertical lines
On
Back-light
On or off?
Off
Hsync,
Vsync
or DE error
Check
power LED
Green
Flash
Check
display
Check inverter
Check I/F board J5
Check I/F board CN5
Check panel connector
resolution
Check I/F board
Check SW board
SW1~SW4
Check I/F board
OSD no response
too dim
Check OSD
adjustment
Check SW board JP1
Check I/F board
The brightness is
different between
upper side and
downer side.
Check backlight
RGB
signal
error
H,Vsyn
c error
partly picture
without color
Check I/F board
Check LCD panel
Vertical, Horizontal
none
synchronousness
a few of colorfully
vertical lines
Check LCD Panel
even(or odd)
vertical lines is dark
LT1201 User Manual (020-1080-00 Rev. A)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
JP1 , +12V
INPUT
Debug Procedure
Does the
NO
YES
screen
Solution with
No display
NO
Display
NO
Lost some
bits
YES
of RGB??
CHK R1(R ),
R2 (G),R3(B)
YES
C1，C2，C3
CHK OSD
U4 pin119~124
(PUSH KEY SWITCH)
CHK U4
pin 79~86
RETURN
LT1201 User Manual (020-1080-00 Rev. A)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
No screen
handle
(2)
CHK PWR
REF: power
LED always
ON or always
OFF when
power on
ok ?
NO
YES
Back-light
ok ?
CHK U5
SOFTWARE
YES
NO
、KEY PAD
NORMAL
CHK
CN5 PIN18、20、30
NO
U4
SCALER
INPUT/OUTPUT
ABNORMAL
CHK Panel
Backlight
D-SUB VGA
15PIN
CHK
YES
U11、Q10、
DVI-D
OK
NG
CHK U4
PIN 110、111
NG
CHK
CN5 INPUT
NG
REPLACE
OK
U4
YES
CHK
SOFTWARE
OR
RETURN
CHK LCD-VCC
CABLE
CHK DE & D-SHCLK
CHK Panel
CONNECTOR
CHK R、G、B SIGNAL
LT1201 User Manual (020-1080-00 Rev. A)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER FLOW
J9,12V
INPUT
CHK FUSE F1
abnormal
abnormal
CHK
U7 input +12V
U7 output +5V
REPLACE U7
REPLACE U9
normal
CHK
U9 input +5V
U9 output +3.3V
normal
abnormal
CHK
U4 Pin 21 +1.8V
U4 Pin 126 +1.8V
REPLACE U4
normal
Return
LT1201 User Manual (020-1080-00 Rev. A)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Upgrade software method
Instructions for flashing firmware
1. Disconnect any peripherals connected to the parallel port on the computer. Disconnect the DVI cable from the
computer
2. Connect the DVI cable to the DVI to VGA adapter, and then connect the VGA side of the adapter to the ISP
board. Connect the ISP board to the computer with the supplied parallel cable. (check Jumper No.4 and No.8
of SW3 to be ON at ISP board, the rest of all to be OFF). Connect the mouse and keyboard to the computer.
All PC information will show on the other VGA monitor.
3. Plug in the USB flash drive.
LT1201 User Manual (020-1080-00 Rev. A)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4. On the flash drive you will find a folder named “ISP program for Mstar TSUM_write_code”, open it and start
ISP_Tool_3.75.3.exe
5. Press connect. A pop‐up window showing “Device type is MX25L512” should appear. If the pop‐up window say
“Can’t entry ISP mode” recheck the cables.
LT1201 User Manual (020-1080-00 Rev. A)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Next press the big red button on the top, and then press the smaller read button
7. Select the AU5T015QT1_1E0A.BIN and open.
LT1201 User Manual (020-1080-00 Rev. A)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Check and re‐check the Checksum. It should be 0x1E0A.
9. Press the Auto button right next to the read button. Check that the setting is according to picture above.
10. Press “Run”. The program will start to erase and reprogram the firmware. Sometimes the programming fails, if
that happens, just restart the process by hitting “Run” again. When the ISP board is cold this can happen a
couple of times before you get a successful run.
11. Disconnect the ISP board and connect the DVI cable from the monitor to the computer again. Make sure that
there’s a video signal going to the screen. Locate the screens power supply. Press and hold the select button
on the screen while you disconnect and reconnect AC power. The screen should show a message saying “All
reset”. The screen will go into burn‐in mode if there’s no video signal. If you have problems getting a signal to
the monitor you can do the reset after step 18.
LT1201 User Manual (020-1080-00 Rev. A)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Revision Control
DATE:
DESCRIPTION:
January 2011
Document number 020-1080-00 Rev. A
Planar Systems, Inc.
Corporate Headquarters
1195 NW Compton Drive
Beaverton, OR 97006-1992
Planar Customer Support
Telephone:
US: 1-866-PLANAR1 (866) 752-6271
Outside US: (503) 748-5799
E-mail: [email protected]
Hours: M-F, 3am-7pm ET, 11am-3am GMT
© 2008 Planar Systems, Inc. Planar is a registered trademark of Planar System, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice
LT1201 User Manual (020-1080-00 Rev. A)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|