QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
Planar Battery System
Model BAT24SI
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
OPERATIONS MANUAL
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Contents
Contents
Index
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Regulatory Compliance
Product Information
Warranty
About the Planar Battery System. . . . . . . . . . . . . . . . . . . . . . . . .1
Battery Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Identify the Connector Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Install the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Charge the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Set Up the Power Management System. . . . . . . . . . . . . . . . . . . .7
Replace the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Battery System Specification. . . . . . . . . . . . . . . . . . . . . . . . . . .16
Overview of Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . .21
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
QUICK LINKS
Product Information
Contents
Warning
Index
Safety guidelines
• Equipment is not suitable for use
in the presence of a flammable
anesthetic mixture with air,
oxygen, or nitrous oxide.
and safety for the user. To maintain both quality and safety, follow the guidelines and
instructions in this manual.
Regulatory Compliance
Product Information
Warranty
• Use the battery system only as intended.
• The Planar battery system
may be energized or operational
even when disconnected from
the AC power source.
• Do not place the battery system near a window. Exposing the system to rain,
water, moisture or constant direct sunlight can severely damage it.
GETTING STARTED
About the Battery System
• Do not cover or obstruct any venting holes on the battery system.
• If the Planar battery system has
been exposed to liquid, has been
dropped, or if its base has been
damaged, it may pose a shock or
fire hazard. Immediately unplug it
and contact customer service for
assistance.
• Store the battery system within –20 to +65 degrees Celsius. Storing the system
Battery Components
Identify Connector Ports
Install Fuses
outside that temperature range could result in permanent damage.
•
If any cord or cable is frayed or damaged, replace it immediately with another of
the same type and rating as supplied by Planar. The safety and regulatory listing and
certifications are based on cables supplied by Planar.
USING THE BATTERY
• Use and maintain the safety ground plug set (power cord) included with the unit.
• Use care in handling the battery if
any leakage is observed. Avoid
skin contact and wash any areas
that come in contact with this
material immediately.
Charge Battery
• After battery system installation, secure all electrical cords to prevent
accidental damage.
Set Up Power Management
• To clean the exterior chassis of the battery system, follow the IEC 60601 standard for
use in a hospital environment. See cleaning guidelines for more information.
MAINTAINING THE BATTERY
Replace Battery
• Before cleaning the chassis, disconnect the unit from its power source.
• Plug the battery system only into
a grounded power outlet.
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning guidelines
QUICK LINKS
Contents
The Planar battery system continues to operate normally while being cleaned in
a fashion normal for a hospital environment. Use a damp, mildly soapy cloth to clean
the exterior chassis. Drip protection is provided in accordance with the IPX1 rating,
defined in the IEC/EN60529 standard.
Index
Regulatory Compliance
Product Information
Warranty
Service support
Other than battery installation and replacement, the Planar battery system requires no
routine maintenance. Should your battery system require repair, return the unit to Planar
Systems for servicing to maintain product warranty. See the warranty for more information.
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
v
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
About the Planar Battery System
Contents
Certification
The Planar Battery System, model BAT24SI, is designed specifically for point-of care
use. It is modular, compact, and ergonomically suited for effective utilization in the
medical environment.
Index
The Planar Battery System is a
recognized UL 60601-1 component.
Planar does not certify it for use with
any other system.
Regulatory Compliance
Product Information
Warranty
The battery system supplies a regulated +12 VDC. It contains two sealed lead acid
batteries, a medically certified universal input power supply, universal charging
control module, an AC line filter, a cooling fan, and appropriate cabling. All
components are mounted within a sheet metal enclosure, which provides
mechanical strength as well as EMI/EMC protection and shielding.
GETTING STARTED
The Planar battery system is classified as follows:
About the Battery System
• Degree of protection against electric shock: No Applied Part
• Degree of protection against water ingress: IPX1, Drip-Proof Equipment
Battery Components
Identify Connector Ports
Install Fuses
The charging and monitoring electronics control the charge rate of the battery as
well as the maximum discharge level. This ensures safe operation of the battery and
prevents damage from high charge rates and low discharge levels.
USING THE BATTERY
Charge Battery
All battery technologies lose their energy storage potential through use. For more
information about the battery cells used in the Planar Battery System, see page 17 to
consult the manufacturer specifications.
Set Up Power Management
MAINTAINING THE BATTERY
The output voltage regulator provides a regulated +12 VDC at a power level up to
72 watts. No external regulators are required for 12-volt applications.
Replace Battery
Troubleshooting
electrically isolate the battery from all electronic components during transportation.
APPENDIXES
See the technical specification for more information.
Specifications
Planar Battery System BAT24SI
1
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Battery Components
Contents
The Planar Battery System ships with all the components you need to make
it operational.
Index
Regulatory Compliance
Product Information
Warranty
Battery unit, model BAT24SI
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
Input power cord
USB cable
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Output power cord
Troubleshooting
APPENDIXES
Three 6 A fuses (size 0.25 in. x1.25 in.;
F type) and three fuse holders
Specifications
Planar Battery System BAT24SI
2
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Identify the Connector Ports
All external connections to the battery unit are located on the rear of the enclosure.
The design of the enclosure minimizes liquid ingress.
Contents
Legend
Index
1 Standard IEC 120–250 VAC
input power
2 A, 250 V replaceable
Regulatory Compliance
Product Information
Warranty
2 USB serial port
Communication channel
between the power supply and
its host computer
GETTING STARTED
3 12V DC 6 A output power
Mini-DIN 4-pin device; requires
an external power cable
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
4 Output power fuse
(size 0.25x1.25; F type)
6 A replaceable
5 LED indicator
USING THE BATTERY
6 Battery fuse
(size 0.25x1.25; F type)
6 A replaceable
6
2
4
1
3
5
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
3
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Install the Fuses
You need the three fuses and a #2 flathead screwdriver for this installation.
Contents
About the battery fuses
The Planar Battery System requires
two 6 A fuses (size 0.25 in. x1.25 in.;
F type). These are available from
any hardware store.
Index
To install the fuses
Regulatory Compliance
Product Information
Warranty
1 Insert the two fuses for the battery into the ports on the rear of the enclosure.
Push the fuses in until you feel the connection. Repeat to install the fuse for
the output power.
Securing the fuse connection
Use the screwdriver to turn the fuse
holder approximately a quarter to
the right, or until you feel it lock.
Do not overtighten.
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
USING THE BATTERY
Charge Battery
2 Use a flathead screwdriver to secure each connection. Do not overtighten.
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
4
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Contents
Sealed lead-acid batteries are cost-effective and can provide a sizable amount of
energy per battery weight. However, the energy storage potential of the batteries
does decay over time.
Index
Regulatory Compliance
Product Information
Warranty
Refer to these web sites for more information on sealed lead-acid batteries:
Battery charging
GETTING STARTED
Plug the battery system into an AC power source for charging. The LED turn yellow
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
See specifications on battery modes and power consumption efficiency for
more information.
Charge time
USING THE BATTERY
The charging controller board is capable of independently charging the batteries
while powering the attached system. This ensures that the charge rate of the
batteries is the same whether a load is connected or not. Charge time varies
depending on the age and usage of the battery. Typically, as a battery ages, it
tends to accept less charge; that is, the charge time decreases. Consequently,
as the battery accepts less charge, the battery usage time decreases.
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Capacity of Charge
Troubleshooting
3 hours
4 hours
6 hours
80%
90%
APPENDIXES
Specifications
100%
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Periodically, charge the battery for 10 hours. This assures that the maximum charge
capacity of the battery is maintained. The charger enters the trickle charging cycle
after the current supplied to the batteries drops below .5 amps. Charge the batteries
for 10 hours for every eight charges to 100%.
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
Battery discharging
You discharge the battery by (1) disconnecting the battery system from the
AC power source and (2) powering the load.
When the battery has been discharged for a long period of time, it reaches a point
at which it needs to cut off power to its load. The battery system communicates to
the host computer and requests a safe shutdown or hibernation.
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
Thermal protection
The universal power supply is thermally protected and self-resetting. The battery
enclosure contains a cooling fan that is activated whenever the system is plugged
into an AC power source.
USING THE BATTERY
Depth of discharge protection
Charge Battery
After the power to the load is cutoff, the internal circuitry goes into sleep mode to
prevent further battery discharging. The sleep mode is intended to prevent the
batteries from deep discharge.
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
6
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Set Up the Power Management System
All communications occur through the USB serial interface. These are displayed
through the Windows Power Options Properties dialog on the host computer.
Contents
Easier power management
Index
The charge level indicator is
software-driven, complying with
the Microsoft Windows HID Power
Device Specification.
To set up power management
Regulatory Compliance
Product Information
Warranty
1 Open the Control Panel and click the Power Options tool.
You manage power consumption
using the Power Options tool in
the Windows Control Panel.
GETTING STARTED
Operating system
About the Battery System
•
•
Windows XP
Battery Components
Identify Connector Ports
Install Fuses
Windows 2000
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Click the Alarms tab on the Power Options Properties dialog.
QUICK LINKS
Contents
Recommended alarm settings
Index
•
Low battery alarm – activate at 3%
The alarm is triggered when the
battery charge level reaches its low
battery limit.
Regulatory Compliance
Product Information
Warranty
•
Critical battery alarm – activate at 0%
The alarm is triggered when the
battery charge level reaches its
depth of discharge limit.
GETTING STARTED
About the Battery System
Hibernation/shut down action
Battery Components
Identify Connector Ports
Install Fuses
If a hibernation or shut down action
is enabled, the low or critical battery
alarm limit should not be greater than
5% to ensure proper operation.
Hibernation and power loss
USING THE BATTERY
The battery system has a built-in safety
feature that prevents power loss during
hibernation. When the battery reaches
0% power, it does not turn off. The
battery system puts the computer into
hibernation before cutting off power to
the computer.
Charge Battery
3
To set either the low battery alarm or critical battery alarm, or both alarms:
• Click the check box to activate alarm mode.
Set Up Power Management
MAINTAINING THE BATTERY
• Move the slider to the point at which you want the alarm to trigger.
Replace Battery
• Click the Alarm Action button to do one or more of the following: select
Troubleshooting
Alarm disabled
Deselect the check box to disable the
low battery or critical battery alarm.
APPENDIXES
Specifications
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
8
4 Select the notification you want, one of the two types or both. Click OK.
QUICK LINKS
Contents
Recommended alarm notification
Index
•
Low battery alarm
Notification: Sound, Text
Action: No action
Regulatory Compliance
Product Information
Warranty
Run Program: None
Critical battery alarm
Notification: None
Action: Hibernate
•
GETTING STARTED
About the Battery System
Run Program: None
Battery Components
Identify Connector Ports
Install Fuses
To set an alarm action:
1
Click the check box to activate a
notification action.
2
For an alarm action, select an
option from the pull-down list.
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Open the Power Meter tab to check the power status of each battery.
• Click the check box to see the details on a battery.
• Click a battery icon for more information.
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SAI
10
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Replace the Battery
You need a #2 Phillips screwdriver and a #2 flathead screwdriver for this installation.
Contents
Index
To remove the battery tray
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
1 Use the Phillips screwdriver to remove 2 Unplug the USB cable and the
3 Unplug the power cord.
the two screws from the front of the
enclosure. Then remove the screw
(top center) from the back, as shown.
output power cable.
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
4 Use the flathead screwdriver to
remove the three fuses. Make a
quarter turn counterclockwise.
5 Pull out the battery tray carefully.
Note: The battery cables may catch on
the sheet metal lip during removal.
6 Make sure the battery tray is seated
on a flat and stable surface.
Specifications
Planar Battery System BAT24SI
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove the used batteries
QUICK LINKS
Contents
Replacement tips
Never insert fuses into or remove
them from the battery with the load
plugged in. Doing so can cause
permanent damage to the system.
Index
Regulatory Compliance
Product Information
Warranty
The battery system weighs about
25 pounds and is heavily weighted
toward the front. Handle it carefully.
GETTING STARTED
Once the unit is completely out of
the enclosure, move it to a flat and
stable work surface to replace the
batteries.
About the Battery System
1 Remove the two Phillips screws
on the retaining bracket and lift
the bracket off.
2 Detach the battery cables from
the controller board.
Battery Components
Identify Connector Ports
Install Fuses
Do not mix old and new batteries.
Replace both batteries during the
same maintenance session.
When reconnecting the battery
cables to the battery terminals,
be sure the connections match
RED-to-RED and BLACK-to-BLACK.
USING THE BATTERY
Charge Battery
Set Up Power Management
The battery system is a self-aligning
unit. When you return it to the
enclosure, push it all the way in.
The alignment occurs automatically.
MAINTAINING THE BATTERY
Replace Battery
3 Detach the battery cables from
4 Place the battery cables to the side
Use only Yuasa NP 12-12 or
B&B EP 12-12 batteries.
and remove the used batteries.
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To reinstall the battery system
QUICK LINKS
Contents
1 Install new batteries into the tray. Replace both batteries at the same time.
Do not mix old and new batteries
Index
2 Reconnect the battery cables to the controller board and to the four battery
terminals. Be sure that cable and terminal connections match RED-to-RED and
BLACK-to-BLACK. Push in each connector until you feel the connection click.
Regulatory Compliance
Product Information
Warranty
3 Reattach the retaining bracket with the two Phillips screws.
4 Push the battery tray all the way into the enclosure.
5 Reinsert the fuses. Use the flathead screwdriver to make a quarter turn
GETTING STARTED
clockwise to secure each connection. Do not overtighten.
About the Battery System
6 Plug in the power cord, USB cable, and power output cable.
Battery Components
Identify Connector Ports
Install Fuses
7 Reinsert the Phillips screws on the back and front of the enclosure.
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
13
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Troubleshooting
Contents
Index
Problem
Possible Cause
Possible Solution
Regulatory Compliance
Product Information
Warranty
The battery system not functioning,
no output power, does not charge
when connected to AC power.
AC power is not connected.
Make sure power cord is connected properly.
Input fuse needs to be replaced.
Replace fuse in the input AC connector.
Replace with UL-recognized fuse 2 A,
250 VAC, fast acting, size 5 mm x 20 mm.
GETTING STARTED
Over-temperature protection is activated.
Output power cord not connected properly.
Contact Planar.
About the Battery System
No power supplied to the load.
Make sure that output power cord is
connected correctly.
Battery Components
Identify Connector Ports
Install Fuses
Power switch is off.
Turn on the power switch on your device.
Output fuse needs to be replaced.
Replace the output power fuse located next
to output power connector. Replace with
UL-recognized fuse 6 A, 125 VDC, fast acting,
size 0.25 in. x 1.25 in., type F.
USING THE BATTERY
Charge Battery
Batteries not connected correctly.
Battery not completely charged.
Check battery connections.
Set Up Power Management
System run time is too short.
Connect AC power and let battery charge
completely. Charge status is conveyed
through the Power Meter tab on the
Power Options Properties dialog Note that
the LED turns green at 80% of total charge
capacity.
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Battery capacity is low.
Replace battery.
Specifications
Planar Battery System BAT24SI
14
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Battery Disposal
Contents
Industrial batteries contain lead and sulfuric acid, which are both considered
“hazardous substances.” If batteries are improperly disposed of, for example, thrown
in the trash or illegally dumped, these substances can eventually leak out and
contaminate the surrounding soil and groundwater supply.
Index
Regulatory Compliance
Product Information
Warranty
It is a federal law to properly dispose of lead-acid batteries once they can no longer be
used. Once a battery is purchased, full liability and responsibility lies on the owner to
dispose of the battery.
GETTING STARTED
The law says that responsibility is still on the owner if the battery is disposed of
improperly by dumping in a landfill, or shipping to a scrap dealer who does not
handle it properly and in which environmental damage occurs.
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
It is illegal to dispose of batteries in any way other than ”thermal recovery” or
recycling of the hazardous substances in batteries according to the Environmental
Protection Agency (EPA).
The Department of Transportation (DOT) has strict guidelines for the shipping of
hazardous materials, which result in large fines if they are not followed.
USING THE BATTERY
Charge Battery
Check with your local ordinances for proper disposal procedures.
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
15
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Battery System Specification
Contents
Index
Technical summary
Regulatory Compliance
Product Information
Warranty
The battery system is a self-contained regulated power supply, battery, and charger unit,
packaged in a sheet metal enclosure.
Features
•
•
•
Universal AC input
Regulated 12V DC output
Fast charging
•
•
•
•
Intelligent communications (USB host)
GETTING STARTED
Cooling fan
About the Battery System
Externally accessible fuses
LED
Battery Components
Identify Connector Ports
Install Fuses
Electrical specifications
Input
Input voltage
85 to 265 VAC
Input frequency
Inrush current limiting
Input protection
Power factor
47 to 63 Hz
USING THE BATTERY
<50A peak
Charge Battery
2A, 250V replaceable fuse
0.95 (150 W, 230 VAC)
12 VDC 5%
Set Up Power Management
MAINTAINING THE BATTERY
Output
Output voltage
Output current
Replace Battery
6.0 A maximum
Troubleshooting
72 watts maximum
Automatic upon fault removal
Overload recovery
Overload protection
APPENDIXES
6A replaceable fuse
(size 0.25 in. x1.25 in.; type F)
Specifications
Output efficiency
>88%
–MORE–
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
16
QUICK LINKS
Battery requirements
Contents
Manufacturer specification
Battery type
Sealed lead acid; quantity – 2
Click this icon to open the PDF file
showing Yuasa battery specification.
Index
Yuasa NP12-12 or B and B EP12-12
Refer to the attached specification.
Regulatory Compliance
Product Information
Warranty
Connectors/cables
Input power connector
USB port connector
Standard IEC power connector
Standard USB cable (A male to B male)
GETTING STARTED
Output power connector
Mini-DIN 4-pin device (female),
Kycon KPJ-4S-S
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
Output power mating connector
Suggested manufacturer – Power Dynamics
Part number – DP-003
4-pin male power plug
Pin assignment
Assignment of the 4-pin DIN output
power connector (female) on the
battery unit.
USING THE BATTERY
+12 VDC 1
GND 3
2 GND
Charge Battery
Set Up Power Management
4 +12 VDC
MAINTAINING THE BATTERY
Replace Battery
Detail of output power connector
Troubleshooting
Charge time (new battery)
3 hours to 80%
4 hours to 90%
6 hours to 100%
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
17
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Four modes of the battery system
Contents
Charging mode
Running mode
Standby mode
Off mode
The battery system is plugged into an AC power source.During charging
Index
mode, the attached load to the battery system is operational.The
batteries charge.The cooling fan runs only when the unit is plugged
into an AC power source.
Regulatory Compliance
Product Information
Warranty
The batteries have some level of charge and the battery system is not
plugged into an AC power source. During running mode, the attached
load to the battery system is operational.The batteries discharge.The
cooling fan is off.The load to the battery system is active.
GETTING STARTED
About the Battery System
The batteries have some level of charge, the battery system is not
plugged into an AC power source, and the load is either disconnected
or off.The cooling fan is off.The load is powered when the system is
either turned on or reconnected.
Battery Components
Identify Connector Ports
Install Fuses
The batteries have no charge and the battery system is not plugged
into an AC power source. During off mode, the attached load to the
battery system is not operational, whether connected or turned on.
The controller board is in sleep mode.The cooling fan is off. Plug the
battery system into an AC power source to leave off mode.
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
18
QUICK LINKS
Power consumption efficiency
Contents
The charging controller board has four levels of power consumption: charging, running,
standby, and off.
Index
Regulatory Compliance
Product Information
Warranty
Charging mode
The batteries are charged using a constant current/constant voltage
algorithm. A constant current of 3.0 amps max is applied to each battery
until the voltage on the battery reaches 14.4 V.The current exponentially
decreases to maintain 14.4 V on the battery.The cooling fan is on during
this cycle.The +12 VDC regulator circuitry is powered by the power
supply, and the communication system reports the charge status of
the batteries to the host.
GETTING STARTED
About the Battery System
Running mode
Standby mode
Off mode
The board consumes power at a rate proportional to the power
consumed by the load during its running mode.The board proves to
be 88% efficient when connected to a 4.5 amp load.
Battery Components
Identify Connector Ports
Install Fuses
The board consumes about 8.5 mA of current when in stand-by mode.
A fully charged and new battery lasts about 3 months in the battery
system before it needs to be charged.
USING THE BATTERY
Charge Battery
The board consumes about 350 µA of current when in the stand-by
mode. A fully charged and new battery lasts about 3 months in the
battery system before it needs to be charged.The battery continues
to drain at a rate of 350 µA. Batteries that are not connected to the
controller board have a shelf life of 1 month 97%, 3 months 91%,
6 months 85%, at 68° F.
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
19
QUICK LINKS
Index
A
Contents
controller board, charging 17, 18
power
checking status 10
customer support 22
Index
alarm
connector 3
consumption 19
management 7
critical battery 8
disabled 8
low battery 8
setting 8, 9
D
Regulatory Compliance
Product Information
Warranty
discharge protection 6
discharging battery 6
disposing of battery 15
Power Meter tab 10
Power Options tool 7
product information iv
protection
B
F
battery
fuses 3, 4
guidelines
cleaning v
safety iv
charging 5
connector ports 3
discharge protection 6
discharging 6
depth of discharge 6
thermal 6
GETTING STARTED
About the Battery System
R
regulatory information 24
reinstalling battery 13
removing battery 11
replacing battery 11, 12
Battery Components
Identify Connector Ports
Install Fuses
disposal 15
I
fuses 3, 4
identifying components 3
IEC connector 3
information
maintaining system 11
output power 3
power consumption 19
reinstalling 13
S
safety guidelines iv
service v
setting alarm 8
specification, battery 16
symbol explanations 26
product iv
regulatory 24
USING THE BATTERY
installing fuses 4
Charge Battery
removing 11
M
replacing 11, 12
specifications 16
standalone 2
thermal protection 6
USB serial port 3
Set Up Power Management
maintaining battery system 11
T
N
thermal protection 6
troubleshooting 14
MAINTAINING THE BATTERY
notification, alarm 9
Replace Battery
O
U
C
output power 3
USB serial port 3
charging battery 5
charging controller board 17, 18
cleaning guidelines v
compliance 24
Troubleshooting
W
port 3
warranty 21
Windows HID power device 7
workstation, cleaning v
overview of battery system 1
APPENDIXES
P
ports, connector 3
components, identifying 3
Specifications
Planar Battery System BAT24SI
20
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Overview of Standard Warranty
Contents
Summary
Index
• Standard 1-year “repair and return” warranty
• Typical repair turnaround time of 10 business days
• Repair facilities and technical support in the United States and in Europe
Regulatory Compliance
Product Information
Warranty
Standard Warranty Return Procedure
As a Planar Standard Warranty customer, you must follow the procedure below if you
have a non-functioning Planar Battery System. Planar customer service staff will attempt to
correct any minor issues that may be causing the problem. Once Planar has determined that
you have a non-functioning product, Planar will arrange for return and repair of the non-
functioning product.
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
1
(866) PLANAR1 (866.752.6271) and select Option 4. In Europe, call +358 9 420 01 or
send your info by fax to +358 9 420 0200. You must have the model number, serial
number, and proof-of-purchase available.
USING THE BATTERY
2
Planar customer service staff will attempt to correct any minor issues that may be
causing the problem. If we are unable to correct the problem to your satisfaction,
we will issue a Return Material Authorization (RMA).
Charge Battery
Set Up Power Management
3
4
You must return the product, as specified, to Planar Systems. Do not return the
battery cell or cart to planar Systems unless directed by Planar customer service.
MAINTAINING THE BATTERY
Planar will validate the defect, repair the unit, and return the unit to you. The typical
turnaround time is 10 business days.
Replace Battery
the customer to properly package the hardware, include all appropriate materials, and return
it to the location specified by Planar customer service.
Troubleshooting
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Summary Limitations and Exclusions
QUICK LINKS
1
2
3
4
5
Warranty is valid only for the first consumer purchaser (non-transferable).
Warranty does not cover the battery cells. Battery cells are consumable items.
The customer must provide original proofs of purchase.
Contents
Customer support
In North America, call 1 (866) PLANAR1
and select Option 4 between 8 A.M. and
5 P.M. Pacific time, Monday through
Friday, or send a description of your
technical issues and e-mail address to
Index
Regulatory Compliance
Product Information
Warranty
Warranty is void on any product with a defaced, modified, or removed serial number.
Warranty is void on any product with damage, deterioration, or malfunction resulting
from the following:
a) Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
In Europe, call +358 9 420 01 between
8 A.M. and 4 P.M. Finnish time (Eastern
European time), Monday through
Friday, or send a description of your
technical issues and e-mail address to
GETTING STARTED
b) Repair or attempted repair by anyone not authorized by Planar.
c) Any damage of the product due to shipment.
About the Battery System
Battery Components
Identify Connector Ports
Install Fuses
d) Removal or installation of the product.
e) Causes external to the product, such as electric power fluctuations or failure.
f) Use of supplies or parts not meeting Planar specifications.
g) Normal wear and tear, including backlights dimming over time.
h) Any other cause which does not relate to a product defect.
Warranty excludes removal, installation, and setup service charges.
USING THE BATTERY
Charge Battery
6
Set Up Power Management
Limitation of Implied Warranties
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Exclusion of Damages
QUICK LINKS
THE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWING:
Contents
Index
1
DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS
OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
Regulatory Compliance
Product Information
Warranty
2
3
ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL, OR
OTHERWISE.
GETTING STARTED
ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
About the Battery System
Effect of Local Law
Battery Components
Identify Connector Ports
Install Fuses
This warranty gives you specific legal rights, and you may have other rights, which vary from
locality to locality. Some localities do not allow limitations on implied warranties and/or do
not allow the exclusion of incidental or consequential damages, so the above limitations and
exclusions may not apply to you.
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
23
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK LINKS
Regulatory Compliance
Contents
Caution
U.S. Federal Communications Compliance Statement
To comply with the limits for an
FCC Class B computing device,
always use the cords supplied with
the unit. The FCC warns that changes
or modification of the unit not
expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment.
Index
The Planar Battery System (model BAT24SI) has been tested and found to comply within the
limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against interference in a residential installation.
Regulatory Compliance
Product Information
Warranty
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation.
GETTING STARTED
If this equipment does cause harmful interference to radio or television reception (which can
be determined by turning the equipment on and off), the user is encouraged to try to correct
the interference by using one or more of the following measures:
About the Battery System
Battery Components
Identify Connector Ports
Install Battery Fuses
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
USING THE BATTERY
• Consult the dealer or an experienced radio/TV technical for help.
Charge Battery
Canadian DOC Notice
Set Up Power Management
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the Radio Interference Regulation of the Canadian Department of
Communications.
MAINTAINING THE BATTERY
“Le present appareil numerique n’emet pas de bruits radioelecinques depassant les limires
applicables aux appareils numeriques de la class B prescrites dans le Reglement sure le
Replace Battery
Troubleshooting
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance
QUICK LINKS
This system has been tested and found to comply with IEC/CSA 601-1, UL 60601-1 and
CAN/CSA C22.2 No. 601.1 medical standards by CSA.
Contents
Index
Because many medical offices are located in residential areas, the Planar battery system, in
addition to meeting medical requirements, has also been tested and found to comply with the
limits for Federal Communications Commission (FCC) Class B computing devices in a typically
configured system. It is the responsibility of the system integrator or configurer to test and
ensure that the entire system complies with applicable electromagnetic compatibility (EMC)
laws. Planar Systems, Inc. has made great efforts to support the medical device industry, in
particular medical device manufacturers and medical device system integrators. We offer
state-of-the-art systems that are compliant with worldwide accepted medical device safety
standards, and for the European market, EC-marked displays based on compliance with
counsel directive 93/42/EEC — commonly referred to as the Medical Device Directive (MDD).
The following summarizes our qualification of these displays as it relates to compliance with
the MDD.
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Battery System
Battery Components
Identify Connector Ports
Install Battery Fuses
USING THE BATTERY
Charge Battery
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
Troubleshooting
APPENDIXES
Specifications
–MORE–
Planar Battery System BAT24SI
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbol explanations
QUICK LINKS
Following are explanations of the symbols found on the Planar Battery System,
model BAT24SI.
Contents
Index
E226863
Product has been tested and certified with respect to electric shock,
Regulatory Compliance
Product Information
Warranty
fire, mechanical and other specified hazards only in accordance with
US 2601-1 and CAN/CSA C22.2 No. 601.1 and IEC 60601-1 for medical
UL 60601-1
CAN/CSA C22.2 NO.601.1
CLASS 8750
equipment. If this mark appears with the indicators“C”and“US”, the
product is certified for Canadian and U.S. markets, meeting the
applicable Canadian and U.S. standards.
GETTING STARTED
Product has been tested to comply with FCC Class B standards.
About the Battery System
Battery Components
Identify Connector Ports
Install Battery Fuses
Consult accompanying documents.
Indoor use only.
USING THE BATTERY
Charge Battery
IPX1
Drip-Proof rating per IEC/EN60529.
DC (direct current) voltage.
Set Up Power Management
MAINTAINING THE BATTERY
Replace Battery
AC (alternating current) voltage.
Fuse.
~
Troubleshooting
APPENDIXES
Specifications
Planar Battery System BAT24SI
Download from Www.Somanuals.com. All Manuals Search And Download.
26
|