SOUND & VISION MIXER
SVM-1000
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Environment
We Want You Listening For A Lifetime
Operating environment temperature and humidity:
+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH
(cooling vents not blocked)
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c_A_En
Selecting fine audio equipment such as the unit
you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
WARNING
Before plugging in for the first time, read the following
section carefully.
Decibel
Level Example
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230V
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock
at two feet.
or 120V) written on the bottom panel.
D3 4 2 1 4
A
En mod
Sound can be deceiving. Over time your hearing
“comfort level” adapts to higher volumes of sound.
So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers,
thunderclap
140 Gunshot blast, jet plane
180 Rocket launching pad
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
Once you have established a comfortable sound
level:
• Set the dial and leave it there.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
Information courtesy of the Deafness Research Foundation.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
on vacation).
D3-4-2-2-1a_A_En
S001 En
Contents
CONFIRM ACCESSORIES..............................................4
USING THE JPEG VIEWER..........................................31
BEFORE USING THE JPEG VIEWER...........................................31
JPEG VIEWER SETUP..................................................................31
CAUTIONS REGARDING HANDLING............................4
Location.......................................................................................... 4
Cleaning the Unit........................................................................... 4
Disclaimer ...................................................................................... 4
About Copyright............................................................................. 4
THE VIDEO EQUALIZER FUNCTION............................34
SET UP THE VIDEO EQ................................................................34
TURNING THE EQUALIZER ON/OFF ..........................................34
FEATURES ....................................................................4
NAMES AND FUNCTIONS OF PARTS ...........................6
CONNECTION PANEL ................................................................... 6
OPERATION PANEL ...................................................................... 7
FADER START FUNCTION ..........................................35
CROSS FADER START PLAY AND BACK CUE PLAY................35
PERFORM UTILITY SETUP ..........................................36
MIDI SETTINGS ............................................................................36
SYNCHRONIZING AUDIO SIGNALS TO EXTERNAL
SEQUENCER, OR USING SVM-1000 INFORMATION TO
OPERATE AN EXTERNAL SEQUENCER ....................................36
MIDI CODE LIST...........................................................................37
PERFORM VIDEO MONITOR SETUP .........................................41
KEYBOARD LANGUAGE SETUP.................................................41
CONNECTIONS...........................................................10
CONNECTING INPUTS................................................................ 10
CONNECTING OUTPUTS ............................................................ 11
CONNECTING MICROPHONE AND HEADPHONES ............... 12
CONNECTING THE POWER CORD............................................ 12
BASIC OPERATIONS...................................................13
FADER CURVE SELECTION....................................................... 14
HARDWARE SETUP....................................................42
MIC SETTING ................................................................................42
SYSTEM SETTINGS.......................................................................42
MASTER OUT SETTINGS .............................................................43
LCD SETTINGS..............................................................................43
MONITOR OUT SETTINGS...........................................................43
TOUCH PANEL SETTINGS...........................................................44
RETURNING TO DEFAULT SETTINGS ........................................44
ENDING HARDWARE SET UP....................................................44
USING THE VIDEO CONTROL FUNCTIONS .................15
OPERATING THE VIDEO CROSS FADER .................................. 15
OPERATING THE VIDEO CHANNEL SWITCH ........................... 15
OPERATING IN THE VIDEO SOLO MODE ................................. 16
VIDEO MIX EFFECTS CHART...................................................... 16
USING THE EFFECT FUNCTION...................................17
USING BEAT EFFECTS ................................................................ 17
USING TOUCH EFFECTS............................................................. 19
USING TEXT EFFECTS ................................................................. 20
EDITING TEXT............................................................................... 22
DISPLAYING/HIDING THE MASTER MONITOR........................ 22
EFFECT LIST.................................................................................. 23
TROUBLESHOOTING ..................................................45
ABOUT THE LCD SCREEN ..........................................................46
ABOUT MINIATURE FLUORESCENT TUBE TECHNOLOGY .....46
SPECIFICATIONS........................................................47
3
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIRM ACCESSORIES / CAUTIONS REGARDING HANDLING / FEATURES
CONFIRM
FEATURES
ACCESSORIES
4-Channnel Music and Video Synchromix
Most conventional image mixing devices are limited to the simple
mixing of two video images, but Pioneer’s own uniquely developed
video blending technology makes it possible to simultaneously mix
up to four channels of music and video. Since the synchro control
allows the use of fader and equalizers with each channel, a new,
wider range of performances is possible with the sensation of
using conventional DJ mixers.
Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
“AV Effects” support a wide variety of new
performance styles by synchronizing music and
video.
Equipped with AV Effects that synchronize music effects and video
effects on the large 11-inch LCD touch panel display, allowing up
to 30 types of effects to be applied to your music and images.
CAUTIONS REGARDING
HANDLING
Location
1
2
3
Beat effect: Automatically detects the tempo of the currently
playing track, and applies effects to music and image in synch
with the beat.
Touch effect: By directly touching the image displayed on the
large LCD touch panel, effects can be applied to music and
video more intuitively.
Text effect: Text messages created in synchronization with the
automatically detected track tempo can be displayed with
effects. Text messages can be entered either by the built-in
keyboard or a common USB keyboard.
Install the unit in a well-ventilated location where it will
not be exposed to high temperatures or humidity.
• Do not install the unit in a location which is exposed to direct
rays of the sun, or near stoves or radiators. Excessive heat
can adversely affect the cabinet and internal components.
Installation of the unit in a damp or dusty environment may
also result in a malfunction or accident. (Avoid installation
near cookers etc., where the unit may be exposed to oily
smoke, steam or heat.)
“JPEG VIEWER” allows use of images stored in
external memory for live performances
Up to eight JPEG files saved on SD memory cards or USB memory
devices can be downloaded and used as a still image sampler. By
applying effects or mixing with other videos and images such as
the name of the DJ or event, or graphic logos, you can broaden the
potential of your performance. Additionally, JPEG files can be
loaded and displayed as an automatic slide show.
• When the unit is used inside a carrying case or DJ booth,
separate it from the walls or other equipment to improve
heat radiation.
Cleaning the Unit
• Use a polishing cloth to wipe off dust and dirt.
• When the surfaces are very dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six times with
water and wrung out well, then wipe again with a dry cloth.
Do not use furniture wax or cleaners.
Digital sound/video system for high quality sound
and image
• Never use thinners, benzene, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surfaces.
1
96 kHz/24-bit sampling digital system for high sound quality
Analog signals input from a DJ player are passed through the
shortest possible signal path and digitized using a high-fidelity A/D
converter with 96 kHz/24-bit sampling, producing optimum quality
for digital mixing. Mixing is performed by a 32-bit DSP to eliminate
any degradation in sound quality, while simultaneously using ideal
filtering to produce optimum sound for DJ play.
In order to realize the greatest possible response, the unit also
features a high-rigidity chassis and double-shield construction to
suppress unwanted vibrations that might adversely effect sound
quality, together with a powerful power section and other high-
fidelity technology, thus producing clear, powerful club sounds.
Disclaimer
• Microsoft and Windows are registered trademarks of
Microsoft Corporation, registered in the U.S. and other
countries.
Apple and Mac OS are trademarks of Apple Inc., registered
in the U.S. and other countries.
• The typefaces included herein are partially developed by
DynaComware Taiwan Inc.
2
High-performance video IC digital system for high image
quality
Video signals input through the high-performance ADC are
processed through a high-performance video DSP rated at 600
MHz/32-bit/4800 MIPS (Million Instructions Per Second), thus
preserving the original image’s dynamic range while also
suppressing unwanted noise and producing images with high
fidelity and quality. The same high quality has also been realized
for video effects that normally tend to be a source of image
degradation.
About Copyright
This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by
Rovi Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Rovi
Corporation. Reverse engineering or disassembly is prohibited.
In the event that the above noted copy protection function operates
in any channel, some effects (DELAY, ECHO, ROLL, REVERSE
ROLL) will not function.
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Improved design and operability for new club
culture
Based on the concept of creating “a design that fascinates,” the
boxy-shape of previous DJ mixers has been restyled toward an
edgier and more solid design. Great attention has been given to
details of materials and design, such as employing an
“illumination display” on the rear panel visible from the dance
floor.
Operating panel design emphasizes convenience for
simultaneous performances of music and video, with a “channel
symmetry layout” centered around the 11-inch LCD touch panel.
By arranging each channel section symmetrically, further
improvements in operability have been made to assist easy mixing
between music and video, so that effects can be enabled
dynamically from the LCD touch panel.
Installing the SVM-1000 in an EIA rack
The screw holes located on the left and right ends of the front
panel (within the side cover) match the 19-inch EIA rack.
• Remove the 10 screws (five screws each located on the left and
right sides of the unit) before installing the unit to the rack.
Screws
Side cover
• Holes for rack installation can be located when the side covers
are removed.
• Attach the unit to the rack using screws of the appropriate size
(screws not provided with the unit).
Other DJ/VJ performance functions made possible
through digital technology
• When installing the unit in a rack, take care to avoid pinching
your fingers.
1
“VIDEO TRIM” allows adjustment of the luminance of images
input to each channel.
Note
2
“VIDEO EQUALIZER” assigns parameters such as [RGB],
[CONTRAST], [HUE], and [SATURATION] to the equalizer,
allowing synchronization of audio equalizing and video
controls.
“AV SYNC” allows the user to select whether audio and video
controls are linked or adjusted separately.
“VIDEO MONITOR SELECTOR” allows the user to choose
whether the monitor video output shows master only, all
channels, master and each channel, master mixing inversion,
etc.
“FULLY ASSIGNABLE MIDI” allows control of DJ effecter, DJ/
VJ application programs, and other external components.
• Never place this unit directly above a power amplifier, as the
heat given off by the amplifier might result in damage to the unit.
Placing the unit directly above a power amplifier might also
result in ham radio signals being picked up or in other types of
interference.
• Allow at least 1U (43.7 mm) space between this component and
the one mounted above it, so as to assure that the cords
connected to this unit's input/output connectors and terminals
do not touch the component above.
3
4
• Always be sure to remove the unit from its rack before shipping.
• When moving the unit while still installed in its rack, exercise
caution to avoid subjecting the unit to shocks or vibration.
5
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMES AND FUNCTIONS OF PARTS
NAMES AND FUNCTIONS OF PARTS
CONNECTION PANEL
1
2
3
4
5
6
7
5
8
9
10 11
12
6
7
5
2
3
4
5
13
4
3
2
1
AUDIO OUT
S
GN
L
GND
SIGNA GND
1 GND 2 H
T
MASTER
OUT
REC
OUT
PHONO DVD/LINE
L
NE
DVD
BOOTH
MONITO
(TRS)
LINE
DVD
PHONO DVD/LINE
MASTER OUT
2
3 COLD
R
L
MIC2
L
L
L
L
MASTER
ATT
R
L
CONTROL
CONTROL
CONTROL
CONTRO
3
dB
6
dB
0
dB
R
R
R
R
POWER
AC IN
OFF
ON
SYNC
OUT
SYNC
OUT
SYNC
OUT
SYNC
OUT
D
IN
G
TAL
DIGITAL
IN
DIGITAL OUT
fs (Hz)
96
MIDI
14 15 16
17
15
14
OUT
48
k
k
DVD
DVD
MASTER
CR
MONITOR
DVD
DVD
VIDEO OUT
USB
COMPONENT
CB
COMPOSITE
S
VIDEO
S
VIDEO
S
VIDEO
S
VIDEO
Y
V
DEO
VIDEO
VIDEO
VIDEO
S
VIDEO
S
VIDEO
18
19
19
20
21
19
19
22 23
1
2
POWER switch
PHONO input connectors
11 Recording output connectors (REC OUT)
RCA type output connectors for recording.
12 BOOTH MONITOR output jacks (TRS)
Ø 6.3 mm phone-type booth monitor output jacks.
RCA type phono level (MM cartridge) input connectors.
Do not use for inputting line level signals.
3
DVD/LINE input connectors
The sound level output at these connectors can be controlled by
the BOOTH MONITOR level dial, regardless of the setting of the
MASTER LEVEL dial. (Since the output is TRS, both balanced and
unbalanced outputs are supported.)
RCA type line level audio input connectors.
Use to connect a DJ/VJ DVD player or DJ CD player or other line
level output component.
13 Microphone 2 input jack (MIC 2)
4
Signal ground terminal (SIGNAL GND)
Connect microphones equipped with phone-type plug.
Connect the ground wire from an analog turntable.
14 Sync signal output connector (SYNC OUT)
Outputs video sync signal.
This is not a safety ground terminal.
5
CONTROL connector
When connecting a Pioneer DJ/VJ DVD player (sold separately),
the sync signal helps suppress any lag between video and audio
signals.
15 Digital input connector (DIGITAL IN)
RCA-type digital coaxial input connector. Connect to the digital
coaxial output connector from a DJ/VJ DVD player or DJ CD player.
Connect the Ø 3.5 mm mini phone plug of the control cable from
a DJ/VJ DVD player or DJ CD player.
When this is done, this mixer’s fader controls can be used to
perform start and back-cue functions on the connected DJ/VJ DVD
player or DJ CD player.
6
LINE input connectors
• If the sampling frequency of the output signal changes, the
RCA type line level audio input connectors.
Use to connect a cassette deck or other line level output
component.
sound may be interrupted briefly.
16 Sampling frequency selector switch (fs 48 k/96 k)
Use to set the sampling frequency of the digital output to 96 kHz/
24-bit format or 48 kHz/24-bit format.
7
DVD input connectors
RCA type line level audio input connectors.
Use to connect a DJ/VJ DVD player or DJ CD player or other line
level output component.
Turn power off before changing this switch position.
17 Digital output connector (DIGITAL OUT)
RCA type digital coaxial output connector.
Master audio digital output.
8
Audio master output 1 connectors (MASTER OUT 1)
XLR type (male) balanced output.
• When using a cord with RCA-type plug, users are recommended
to connect the plug directly to the MASTER OUT 2 connectors
without using an XLR/RCA converter plug.
When a conversion plug is used, the signal GND may become
unstable, in rare cases resulting in the production of noise.
18 Power inlet (AC IN)
Use the furnished power cable to connect to a household AC
outlet.
19 Video input connectors (DVD, VIDEO, S-VIDEO)
Composite and S-VIDEO type video input connectors.
20 Video master output connectors
(MASTER: COMPONENT, COMPOSITE, S-VIDEO)
Component, composite, and S-VIDEO type video output
connectors.
9
Audio master output attenuator selector (MASTER ATT.)
Attenuates the output level of the audio master 1 and audio master
2.
Attenuation level can be selected as 0 dB, –3 dB, or –6 dB.
10 Audio master output 2 connectors (MASTER OUT 2
)
21 Video monitor output connectors (MONITOR, S-VIDEO)
Composite and S-VIDEO type monitor video output connectors.
RCA-type unbalanced output.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMES AND FUNCTIONS OF PARTS
22 MIDI OUT connector
23 MIDI USB output connector
DIN type output connector.
Use to connect to other MIDI component.
USB-B type output connector. Use to connect to a computer.
OPERATION PANEL
VIDEO INPUT
VIDEO
VIDEO INPUT
VIDEO
VIDEO INPUT
VIDEO
VIDEO INPUT
VIDEO
DVD
VIDEO
MASTER LEVEL
14
16
17
32
DVD
DVD
DVD
S-V DEO
S
VIDEO
S-V DEO
S
V
DEO
15
18
1
USB
VIDEO
EX
VIDEO
EX
CH
1
18
BLACK
WH TE
VIDEO TRIM
VIDEO TR M
VIDEO TRIM
VIDEO TR M
V
DEO
EX
MONO STEREO
18
18
20
CH
4
33
34
UTIL TY
21
2
3
MASTER
AUD O MASTER LEVEL
MIN
MAX
M
N
MAX
MIN
MAX
M
N
MAX
MONITOR
MIC
CH SELECT
SET UP
AUDIO INPUT
AUDIO INPUT
DVD LINE DIGITAL
AUDIO INPUT
DVD LINE DIG TAL
AUDIO INPUT
PHONO
19
22
DVD
L
NE
PHONO
LINE
40
41
45
0
V DEO EQ
ON/OFF
SET UP
AUDIO TR M
AUDIO TR M
AUDIO TR M
AUDIO TR M
OVER
OVER
OVER
VER
OVER
23
24
23
23
23
MIC 1
27
10
7
10
7
10
7
10
7
10
7
MIC1
LEVEL
+9
HI
+9
HI
+9
HI
+9
HI
4
5
4
2
4
2
4
4
4
2
VIDEO FX
PATTERN/
TEXT BANK
0
0
2
2
MIC2
LEVEL
24
25
24
25
24
25
1
1
1
1
1
0
0
0
0
0
35
28
46
47
48
26
26
26
+6
+6
+6
26
+6
+6
+6
26
26
26
+6
26
26
26
+6
–1
–2
–3
–5
–7
–10
–15
–24
–1
–2
–3
–5
–7
–1
–2
–3
–5
–7
–1
–2
–3
–5
–7
–10
–15
–24
–1
–2
–3
–5
–7
–10
–15
–24
MID
MID
MID
MID
HI
TIME/
PARAMETER
25
26
6
7
12
+12
LOW
2626
+6 26
+6 26
LOW
LOW
LOW
LOW
–10
–10
12
+12
TALK
LEVEL/
DEPTH
JPEG
VIEWER
–15
–24
–15
–24
MIC OFF ON OVER
8
9
26
42
+6
+6
dB
dB
dB
dB
L
dB
R
FADER START
CH1
MIN
MAX
27
27
27
EFFECT
CUE
CUE
CUE
CUE
CUE
CUE
CH2
CH3
28
49
50
28
28
28
28
MASTER
1
2
3
4
VIDEO
SOLO MODE
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
CH4
BALANCE
43
44
HEAD PHONES
STEREO
MONO SPL
T
FADER
AV SYNC
EFFECT
ON/OFF
36
37
10
11
12
L
R
M XING
BOOTH MONITOR
CUE
MASTER
29
29
29
0
LEVEL
29
30
CROSS FADER
ASS GN
CROSS FADER
ASSIGN
CROSS FADER
ASS GN
CROSS FADER
ASS GN
CH FADER CURVE
38
39
0
A
THRU
A
THRU
A
THRU
B
A
THRU
B
B30
B30
30
51
CROSS FADER CURVE
SD CARD
PHONES
PROFESSIONAL SOUND&VIS ON MIXER
A
B
13
SVM-1000
31
1
USB connector
8
Microphone function selector switch (MIC)
Use to connect a USB memory or keyboard.
CH1/CH4 video input connectors (VIDEO EX)
Use to input video from an external source.
Microphone 1 input jack (MIC 1)
Connect microphone with XLR-type or phone-type plug.
Microphone 1 level control dial (MIC 1 LEVEL)
OFF:
No microphone sound is output.
2
ON:
Microphone sounds are output, and the microphone function
3
indicator lights.
TALK OVER:
4
Microphone sounds are output, and the microphone function
Use to adjust the volume of microphone 1. (Adjustable range –∞ to
0 dB)
indicator flashes.
When an audio signal of –15 dB or more (default setting) is input
to the microphone input, the talkover function operates to reduce
all output other than the mike audio by 20 dB (default setting).
Values can be changed in the hardware setup (P. 42)
• When not using the TALK OVER function, it is recommended to
set the switch to the [OFF] or [ON] position.
5
Microphone 2 level control dial (MIC 2 LEVEL)
Use to adjust the volume of microphone 2. (Adjustable range –∞ to
0 dB)
6
Microphone equalizer high-range adjust dial (HI)
Use to adjust the treble (high-range) frequencies of microphones 1
and 2. (Adjustable range –12 dB to +12 dB)
9
FADER START button/indicator (CH-1 to CH-4)
7
Microphone equalizer low-range adjust dial (LOW)
Enables the fader start/back cue function for the channel to which
a DJ/VJ DVD player or DJ CD player is connected. The button lights
when set to ON. When enabled, the operation differs depending on
the setting of the CROSS FADER ASSIGN switch.
Use to adjust the bass (low-range) frequencies of microphones 1
and 2. (Adjustable range –12 dB to +12 dB)
• When the CROSS FADER ASSIGN switch is set to the [A] or [B]
position, FADER START button operation is linked to the
operation of the cross fader (and unlinked to channel fader).
• When the CROSS FADER ASSIGN switch is set to the [THRU]
position, FADER START button operation is linked to the
operation of the channel fader (and unlinked to cross fader).
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMES AND FUNCTIONS OF PARTS
10 HEADPHONES output switch (MONO SPLIT/STEREO)
23 AUDIO TRIM dial
MONO SPLIT:
Use to adjust the level of the audio input signal for each channel.
The source sound selected with the headphone CUE button is
output to the L channel, while the master sound is output to the R
channel (only when [MASTER] is selected with the headphone
CUE button).
(Adjustable range: –∞ to +9 dB, mid-position is about 0 dB)
24 Channel equalizer high-range adjust dial (HI)
Use to adjust the treble (high-range) frequency sound for each
channel. Video parameters can also be assigned. See P. 34
regarding video parameters. (Adjustable range: –26 dB to +6 dB)
STEREO:
The audio source selected with the headphone CUE button is
25 Channel equalizer mid-range adjust dial (MID)
output in stereo.
11 HEADPHONES MIXING dial
Use to adjust the mid-range frequency sound for each channel.
Video parameters can also be assigned. See P. 34 regarding video
parameters. (Adjustable range: –26 dB to +6 dB)
When rotated clockwise (toward [MASTER]), the master output
audio is produced at the headphones (only when [MASTER] has
been selected with the headphone CUE button); when rotated
counterclockwise (toward [CUE]), the headphones output
becomes the mixture of the effect monitor and the channel
selected with the headphone CUE button.
12 HEADPHONES LEVEL adjust dial
Adjusts the output level of the headphones jack. (Adjustable
range: –∞ to 0 dB)
26 Channel equalizer low-range adjust dial (LOW)
Use to adjust the bass (low-range) frequency sound for each
channel. Video parameters can also be assigned. See P. 34
regarding video parameters. (Adjustable range: –26 dB to +6 dB)
27 Channel level indicator
Displays the current level for each channel, with two-second peak
hold.
28 Headphone CUE buttons/indicators
13 Headphones jack (PHONES)
These buttons are used to select from 1 to 4, MASTER, or
EFFECT CUE, to allow you to monitor the desired source through
headphones. If multiple buttons are pressed simultaneously, the
selected audio sources are mixed. Press the button once more to
cancel the selected source. Unselected buttons glow darkly, while
selected source buttons light brightly.
14 Channel 1 VIDEO INPUT selector switch
Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the
type of input connected.
15 Channel 2 VIDEO INPUT selector switch
Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input
connected.
29 Channel fader lever
16 Channel 3 VIDEO INPUT selector switch
Set to [DVD], [VIDEO], or [S-VIDEO] to match the type of input
connected.
17 Channel 4 VIDEO INPUT selector switch
Set to [DVD], [VIDEO], [S-VIDEO], or [VIDEO EX] to match the
type of input connected.
18 VIDEO TRIM dial
Use to adjust the level of the video input signal for each channel.
• When rotated counterclockwise, the luminance level is reduced,
eventually producing a black screen.
Use to adjust sound volumes and video level for each channel.
(Volume adjust range: –∞ to 0 dB) (Video adjust range: 0 % to
100 %)
Output is in accordance with the channel fader curve selected with
the CH FADER CURVE switch.
When FADER AV SYNC function is OFF, only sound volume can be
adjusted.
30 CROSS FADER ASSIGN switch
This switch assigns each channel’s output to either right or left
side of the cross fader (if multiple channels are assigned to the
same side, the result will be the combined sum of the channels).
• When rotated clockwise, the luminance level is raised,
eventually producing a white screen.
• At the center position, the luminance level is neutral (same level
as input).
A:
The selected channel is assigned to the cross fader’s [A] (left) side.
THRU:
The channel fader’s output is sent as is to the master output,
without being passed through the cross fader.
19 Channel 1 AUDIO INPUT selector switch
DVD/LINE:
B:
Use to select DVD/LINE input connectors (line level analog input).
The selected channel is assigned to the cross fader’s [B] (right)
PHONO:
side.
Use to select PHONO input connectors (PHONO level analog
31 CROSS FADER CURVE switch
This switch allows the user to select from three types of cross fader
curve response.
input).
20 Channel 2 AUDIO INPUT selector switch
DVD:
Sound volume changes as follows:
Use to select DVD input connectors.
• At the left setting, the curve produces a rapid signal rise. (As
soon as the cross fader lever leaves the [A] side, the [B] channel
sound is produced.)
• At the right setting, the curve operates to produce an even,
neutral rise throughout the cross fader’s movement.
• At the middle setting, an intermediate curve is produced,
midway between the two curves noted above.
The video level is as noted above only when the video cross fader’s
video mix effect is set to [FADE].
LINE:
Use to select LINE input connectors (line level analog input).
DIGITAL:
Use to select DIGITAL input connector.
21 Channel 3 AUDIO INPUT selector switch
DVD:
Use to select DVD input connectors.
LINE:
Use to select LINE input connectors (line level analog input).
32 Video master output level dial (VIDEO MASTER LEVEL)
Adjusts the video master output luminance level.
DIGITAL:
Use to select DIGITAL input connector.
33 Master output MONO/STEREO selector switch
When set to the [MONO] position, audio master output is
produced in L+R monaural.
22 Channel 4 AUDIO INPUT selector switch
DVD/LINE:
Use to select DVD/LINE input connectors (line level analog input).
34 Audio master output level dial (AUDIO MASTER LEVEL)
Use to adjust the master output level. (Adjustable range: –∞ to
0 dB)
The master output is the sum combination of the sound from
channels set to [THRU] with the CROSS FADER ASSIGN switch;
the signal passed through the cross fader; and the signals from
microphone 1 and microphone 2.
PHONO:
Use to select PHONO input connectors (PHONO level analog
input).
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
NAMES AND FUNCTIONS OF PARTS
35 Master level indicator (MASTER L, R)
50 Effect button/indicator (EFFECT ON/OFF)
These segment indicators display the audio output level from L and
Turns selected effect ON/OFF.
When power is turned ON, the button lights (defaults to effect
OFF). When effects are enabled (ON), the button flashes.
R channels. The indicators have a two-second peak hold.
36 Master balance dial (BALANCE)
Use to adjust the L/R channel balance for audio master output,
51 Cross fader lever (A/B)
booth monitor output, recording output, and digital output.
This adjusts sound and video levels assigned to sides [A] and [B]
in accordance with the CROSS FADER ASSIGN switches. When
FADER AV SYNC is OFF, the control adjusts the sound only.
37 BOOTH MONITOR level control dial
This dial is used to adjust the booth monitor output volume.
The volume can be adjusted independently of the master output
level. (Adjustable range: –∞ to 0 dB)
38 Channel fader curve switch (CH FADER CURVE)
This switch allows the user to select from three types of channel
fader curve response.
The sound volume and video level changes as follows:
This setting is applied equally to channels 1 to 4.
• At the left setting, the curve operates to produce a rapid rise as
the channel fader approaches its distant position.
• At the right setting, the curve operates to produce an even,
neutral rise throughout the channel fader’s movement.
• At the middle setting, an intermediate curve is produced,
midway between the two curves noted above.
39 SD CARD slot
Insert an SD card.
40 UTILITY button (MASTER MONITOR, SET UP)
Switches between display / no display of the master monitor on the
LCD. When the master monitor is set to display, the indicator
lights. When the button is held depressed, the indicator changes
to flashing, and the LCD screen changes to show the utility setup
menu.
41 VIDEO EQ button (ON/OFF, SET UP)
Switches the video equalizer ON/OFF. The indicator lights when
the video equalizer is ON. When the button is held depressed, the
indicator flashes, and the LCD display changes to show the
equalizer setup menu.
42 JPEG VIEWER button
Use to set the JPEG viewer mode. The indicator lights when in the
JPEG viewer mode.
43 VIDEO SOLO MODE button
Use to switch the video solo mode ON/OFF. When the video solo
mode is ON, the indicator will flash.
44 Fader AV synchro button (FADER AV SYNC)
This button determines whether sound and video are controlled
together, or independently. When set to ON, the indicator lights,
and the channel fader and cross fader operations change both
sound and video simultaneously. When set to OFF, the channel
fader and cross fader levers control sound only, while video is
controlled by the touch panel.
45 Effect channel selector dial (CH SELECT)
Use to select the channel to which effects are applied. When [MIC]
is selected, effects are applied to both microphone 1 and
microphone 2.
46 VIDEO FX PATTERN/TEXT BANK dial
Use to select video effects, video effect patterns and text banks.
47 Effect parameter 1 dial (TIME/PARAMETER)
Adjusts parameter for selected effect.
• If this dial is rotated while depressing the TAP button, direct
BPM can be set manually.
48 Effect parameter 2 dial (LEVEL/DEPTH)
Adjusts quantitative parameters for selected effect.
49 TAP button
The BPM is calculated from the intervals at which the TAP button
is struck.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTIONS
Always turn off the power switch and disconnect the power plug from its outlet when making or changing connections.
CONNECTING INPUTS
4
3
2
1
AUDIO OUT
SIGNAL GND
SIGNAL GND
1 GND 2 HOT
3 COLD
MASTER
OUT
REC
OUT
PHONO DVD LINE
LINE
DVD
BOOTH
MONITOR
(TRS)
LINE
DVD
PHONO DVD LINE
MASTER OUT
1
2
R
L
MIC2
L
L
L
L
L
MASTER
ATT
R
L
CONTROL
CONTROL
CONTROL
CONTROL
3
dB
6
dB
0
dB
R
R
R
R
R
POWER
AC IN
FF
ON
SYNC
OUT
SYNC
OUT
SYNC
OUT
SYNC
OUT
IGITAL
IN
D
IN
GITAL
DIGITAL OUT
fs (Hz)
96
MIDI
OUT
48
k
k
DVD
DVD
MASTER
CR
MONITOR
DVD
DVD
VIDEO OUT
USB
COMPONENT
CB
COMPOSITE
S
VIDEO
S
V
DEO
S
V
DEO
S
V
DEO
Y
VIDEO
V
DEO
VIDEO
V
DE
S
VIDEO
S
V
DEO
L
R
L
R
L
R
L
R
L
R
R
L
Cassette deck, etc.
CD player, etc.
Analog turntable
DJ/VJ DVD player or
DJ CD player
DJ/VJ DVD player or
DJ CD player
Analog turntable
Pioneer DJ/VJ DVD players or DJ CD players
Connecting an analog turntable
Connect the audio output cables from an analog turntable to this
unit’s Channel 1 or 4 PHONO input connectors, then set the
connected channel’s AUDIO INPUT switch (on the upper panel of
this unit) to [PHONO]. This unit’s PHONO input supports MM
cartridges.
Audio cable connection
A DJ/VJ DVD or DJ CD player’s audio output connectors can be
connected to this unit’s DVD, DVD/LINE or LINE connectors.
When using the player’s digital output, connect to this unit’s
channel 2 or channel 3 DIGITAL IN connector. Use the AUDIO
INPUT selector switch (on top panel of this unit) to select the
proper connector.
Connect the ground wire from an analog turntable to the SIGNAL
GND terminal of the SVM-1000.
• Note that no PHONO input connector is provided for channel 2
and 3.
Likewise, the control cord should be connected to the CONTROL
connector of the selected channel.
Connecting other line level output devices
To use a cassette deck or ordinary CD player, connect its audio
output connectors to one of the SVM-1000's LINE input connectors
(channel 1 to 4).
Video cable connection
A DJ/VJ DVD player’s video output connectors can be connected
to this unit’s DVD, VIDEO, or S-VIDEO connectors. When this is
done, use the VIDEO INPUT selector switch (on top panel of this
unit) to select the proper connector.
Likewise, connect a commercially available sync signal cable to
the SYNC OUT connector of the selected channel.
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTING OUTPUTS
Power amplifier
(RCA plug input
connectors)
Digital input AV amplifier
(digital input
Cassette deck
(analog input
recording device)
recording device)
MASTER ATT. switch
R
L
L
R
4
3
2
1
AUDIO OUT
SIGNAL GND
SIGNAL GND
1 GND 2 HOT
MASTER
OUT
REC
OUT
PHONO DVD LINE
LINE
DVD
B
OTH
LINE
DVD
PHONO DVD
L
NE
MASTER OUT
1
2
3 CO
D
R
L
MONITOR
(TRS)
MIC2
L
L
L
L
L
MAST
ATT
dB
R
R
L
CONTROL
CONTROL
CONTROL
CONTROL
3
6
dB
0
dB
R
R
R
R
R
POWER
AC IN
OFF
ON
SYNC
OUT
SYNC
OUT
SYNC
OUT
SYNC
OUT
DIG TAL
N
GITAL
IN
DIGITAL OUT
fs (Hz)
96
MIDI
OUT
48
k
k
DVD
DVD
MASTER
CR
MONITOR
VD
DVD
VIDEO OUT
USB
COMPONENT
CB
COMPOSITE
S
VIDEO
S
VIDEO
S
V
DEO
S
V
DEO
Y
V
DEO
V
DEO
VIDEO
V
DE
S
VIDEO
S
VIDEO
Sampling
frequency
selector switch
Power amplifier
(XLR plug input connectors)
Plasma display
Display
(for monitor)
Power amplifier
(for booth monitor)
Audio master output
This unit is furnished with balanced output MASTER OUT 1
(supporting XLR plugs), and unbalanced output MASTER OUT 2
(supporting RCA plugs).
Using the MASTER ATT. switch, adjust the output level to match
the input sensitivity of the power amplifier used.
If the operating panel’s MONO/STEREO switch is set to [MONO],
the master output will be a monaural combination of L+R
channels.
Recording output
These are output connectors for recording, supporting RCA plugs.
Digital output
This is a coaxial digital output connector, supporting RCA plugs.
The sampling frequency can be set to 96 kHz/24-bit format or
48 kHz/24-bit format to match the connected device.
Turn power off before changing this switch position.
Video master output
Booth monitor output
TRS output for ø 6.3 mm phone plug. The sound volume for this
output is controlled by the BOOTH MONITOR level dial,
independently of the master output level setting.
Supports component, composite (RCA, BNC connector) and S-
VIDEO outputs.
Monitor output
Supports composite and S-VIDEO outputs.
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTING MICROPHONE AND HEADPHONES
Microphone
8
7
6
5
4
3
2
1
0
HEAD PHONES
MONO SPL T STEREO
A microphone with XLR-type or Ø 6.3 mm phone-type plug can be
connected to the MIC 1 connector on the operation panel (upper) .
The MIC 2 jack on the connection panel (rear) can be used to
connect a microphone with Ø 6.3 mm phone-type plug.
MIXING
• When using a microphone, set the operating panel’s MIC switch
to [ON] or [TALK OVER], and adjust the LEVEL dial as
necessary.
CUE
MASTER
LEVEL
CROSS FADER
ASSIGN
When not using a microphone, it is recommended to set the
MIC switch to [OFF] and rotate the LEVEL dial fully
counterclockwise to the [–∞] side.
0
A
THRU
B
PHONES
PROFESSIONAL SO
Headphones
SVM-
USB
Microphone 1
CH 1
VIDEO
EX
CH 4
MIC
MIC 1
External video connector
A camera, DVD player or other video output device can be
connected to the CH 1/CH 4 video input connectors on the
operating panel (top).
MIC2
MIDI
USB
CH 1
OUT
Microphone 2
VIDEO
EX
USB
CH 4
MIC
Video cameras and
devices
MIC 1
Headphones
The PHONES jack on the operating panel (upper) can be used to
connect headphones with a Ø 6.3 mm stereo phone plug.
CONNECTING THE POWER CORD
Connect the power cord last.
When all connections are completed, connect one end of the
furnished power cord to the AC inlet on the rear panel, and the
plug on the other end to a household AC outlet, or the auxiliary
power outlet on an amplifier. Use only the furnished power cord for
this connection.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
BASIC OPERATIONS
POWER
VIDEO MASTER LEVEL
VIDEO
INPUT
VIDEO TRIM
AUDIO MASTER LEVEL
AUDIO TRIM
AUDIO
INPUT
HI
HI, MID,
LOW
HI, MID,
LOW
Channel fader
lever
0
1
9
9
8
7
6
5
4
3
2
1
0
7
5
3
BALANCE
CROSS FADER
ASSIGN
Cross fader lever
(A/B)
1
2
Set rear panel POWER switch to [ON].
6
7
8
Use the channel equalizer dials (HI, MID, LOW) to adjust the
tone.
Set the AUDIO INPUT switch for the desired channel to match
the type of connected component.
• When using the DVD input, set to [DVD].
• When using LINE input, set to [LINE].
• When using DVD/LINE input, set to [DVD/LINE].
• When using DIGITAL input, set to [DIGITAL].
• When using PHONO input, set to [PHONO].
Use the VIDEO INPUT switch for the selected channel to
choose the video input.
Use the channel fader lever to adjust the sound volume of
the selected channel.
To use the cross fader on the selected channel, set the CROSS
FADER ASSIGN switch to either cross fader channel A or
channel B, and operate the cross fader lever (A/B).
• When not using the cross fader, set the CROSS FADER
ASSIGN switch to [THRU].
Use the AUDIO MASTER LEVEL dial to adjust the overall
sound volume.
3
4
5
9
Use the AUDIO TRIM dial to adjust the input level for each
channel.
10 Use the VIDEO MASTER LEVEL dial to adjust the overall
luminance level.
Use the VIDEO TRIM dial to adjust the input level for each
channel.
11 Use the BALANCE dial to adjust the sound balance between
right and left.
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
MONO/STEREO
HI
MIC1 LEVEL
MIC2 LEVEL
HI, LOW
MIC
CUE
0
0
9
9
8
7
6
5
4
3
2
1
0
8
7
6
5
4
3
2
1
0
MONO SPLIT/STEREO
MIXING
BOOTH MONITOR
CH FADER CURVE
LEVEL
CROSS FADER CURVE
4
Use the HEADPHONES LEVEL dial to adjust the headphones’
sound volume.
• Rotate the HEADPHONES LEVEL dial to adjust the sound
level.
• When the Effect mode select button (P. 17) is set to [V]
mode, effect sounds will not be output even if the
EFFECT CUE button is pressed.
Selecting Stereo or Monaural
When the MONO/STEREO switch is set to [MONO], the audio
master output becomes a monaural combination of L+R
channels.
Microphone Input
1
To use a microphone, set the MIC switch to [ON] or [TALK
OVER].
FADER CURVE SELECTION
When set to [TALK OVER], any time a sound of –15 dB (default
setting) or more is input, all sound sources other than the
microphone are attenuated by 20 dB (default setting). These
default values can be changed in the hardware setup (P. 42).
The response of sound volume change to the fader control can be
set in three types.
Use the CH FADER CURVE switch to select the desired channel
fader response curve.
The sound volume and video level changes as follows:
2
3
Use the MIC 1 LEVEL dial to adjust the sound volume of
MIC 1, and use the MIC 2 LEVEL dial to adjust the sound
volume of MIC 2.
• At the left setting, the curve operates to produce a rapid rise as
the channel fader approaches its distant position.
Use the microphone equalizer dials (HI, LOW) to adjust the
tone of the microphone sound.
• At the right setting, the curve operates to produce an even,
neutral rise throughout the channel fader’s movement.
• The microphone equalizer function operates simultaneously
on microphone 1 and 2.
• At the middle setting, an intermediate curve is produced,
midway between the two curves noted above.
Booth Monitor Output
• This setting applies equally to channels 1 to 4.
1
Use the BOOTH MONITOR level dial to adjust the sound
volume.
Use the CROSS FADER CURVE switch to select the cross fader
curve response.
• The BOOTH MONITOR level dial can be used to adjust the
sound volume independently of the AUDIO MASTER LEVEL
dial.
Sound volume changes as follows:
• At the left setting, the curve produces a rapid signal rise. (As
soon as the cross fader lever leaves the [A] side, the [B] channel
sound is produced.)
• At the right setting, the curve operates to produce an even,
neutral rise throughout the cross fader’s movement.
• At the middle setting, an intermediate curve is produced,
midway between the two curves noted above.
• This setting produces equal curve effects for both sides A and B.
• Use the hardware setup (P. 42) to set whether or not the
microphone sound is to be output to the booth monitor.
Headphones Output
1
Use the headphone CUE buttons (channels 1 to 4, MASTER,
EFFECT CUE) to select the source.
• The selected CUE button lights brightly.
2
Set the HEADPHONES (MONO SPLIT/STEREO) switch.
The video level is as noted above only when the video cross fader’s
video mix effect is set to [FADE].
• When set to the [MONO SPLIT] position, the sound selected
with the headphone CUE button is output to the left channel,
and the master sound is output to the right channel (only
when MASTER CUE button is set to ON).
• When set to the [STEREO] position, the sound selected with
the headphone CUE button is output in stereo.
3
When [MONO SPLIT] is selected, use the HEADPHONES
MIXING dial to adjust the balance of sound between the left
channel (sound selected with the headphone CUE button),
and the right channel (master sound).
• When the HEADPHONES MIXING dial is rotated clockwise
(toward [MASTER]), the master output (only when the
MASTER CUE button is ON) increases; when rotated
counterclockwise (toward [CUE]), the sound selected with
the headphone CUE button increases.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE VIDEO CONTROL FUNCTIONS
USING THE VIDEO CONTROL FUNCTIONS
Touch the LCD screen to control video functions. Supports video cross fader functions and video channel switch functions.
2
Touch a video mix effect button to choose a video mix effect.
VIDEO SOLO MODE
• The selected button will appear white, and the icon will move
as an animation.
• For each effect refer to P. 16.
3
Operate the video cross fader.
• The video will change as video mix effects are being applied.
• When FADER AV SYNC is set to ON, the video cross fader
section’s [AV SYNC] indicator will appear, and the video
cross fader will operate in synchronization with the cross
fader. Touching the video cross fader allows you to
manipulate the video while you are touching it. Release to
return to the same position as the cross fader.
• When FADER AV SYNC is set to OFF, the video cross fader
section’s [AV SYNC] indicator goes out, and the sound and
video are controlled independently. The sound is controlled
by the cross fader, and the video by the video cross fader.
• When the [TRANS] button is touched, the video
corresponding to the touched side will be output regardless
of the position of the video cross fader.
HI
1
0
9
FADER AV
SYNC
8
7
6
5
4
3
2
1
0
CROSS FADER
ASSIGN
Cross fader lever (A/B)
• When all cross fader assigns are set to [THRU], the video
cross fader and [TRANS] button will appear gray, and if
assigned, the buttons will function as video cross fader,
[TRANS] buttons, with [A] side appearing blue and [B] side
appearing red.
OPERATING THE VIDEO CROSS FADER
The video cross fader is used to manipulate video images.
2
OPERATING THE VIDEO CHANNEL
SWITCH
1
3
The channel monitor functions as a switch to turn that channel’s
video ON/OFF.
1
Touch the channel monitor.
• The touched video output will alternate ON/OFF.
• When FADER AV SYNC is set to ON, the video level will be
displayed in red. If the video level is not dispayed (channel
fader is [0]), touch the channel to output that channel’s
video. Or alternately, when the video level is displayed,
touching the channel monitor will cause that channel’s
video to turn off during the duration the screen is touched.
• When FADER AV SYNC is set to OFF, the video level is
displayed in green. The channel monitor can be touched to
alternate that video output ON/OFF.
5
4
5
1
2
Channel
monitor
Monitors videos from each input channel
(1 through 4).
Touch the channel monitor to output the
video of each channel.
Video level
Indicates video output level.
Appears red when FADER AV SYNC is
ON, and appears green when FADER AV
SYNC is OFF.
3
4
5
Video mix effect Use to select type of video change when
button
video cross fader is operated.
Video Cross
fader
Video cross fader.
Transfomer
button [TRANS]
Outputs video of touched side, regardless
of position of video cross fader.
1
Using the CROSS FADER ASSIGN switch, choose either
Channel A or Channel B of the cross fader
• When assigned to Channel [A], the border of the channel
preview monitor appears blue; when assigned to Channel
[B], the border of the channel preview monitor appears red.
When assigned to [THRU], the border appears gray.
• When JPEG is assigned, the [JPEG] indicator will appear at
the upper left of the channel monitor.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE VIDEO CONTROL FUNCTIONS
OPERATING IN THE VIDEO SOLO MODE
When FADER AV SYNC is ON
• When the channel monitor is touched, output instantaneously
switches to the video of the touched channel.
Setting video solo mode to ON allows instantaneous switching to
the desired channel’s video.
• When the channel fader begins rising from the [0] position,
output instantaneously switches to that channel’s video.
By combining with the FADER AV SYNC button ON/OFF, a variety
of operations is possible.
Whenever the power is first turned ON, the video solo mode is set
to OFF by default.
When FADER AV SYNC is OFF
• When the channel monitor is touched, output instantaneously
switches to the video of the touched channel.
When the video solo mode is ON, the VIDEO SOLO MODE button
will flash.
Upon changing the FADER AV SYNC from ON to OFF, the original
channel fader position will be maintained until the channel
monitor is touched again.
Operation of the video cross fader and [TRANS] button are not
supported in the video solo mode.
VIDEO MIX EFFECTS CHART
Video mix effects
Video cross fader
No Name
Description of the effect
1
2
3
4
FADE
Switches video while mixing.
WIPE
Switches video while wiping away.
Switches instantaneously (without mixing).
SWITCH
CHROMA-B
Switches from the blue component of video on cross fader side [A] to the
video on side [B].
5
6
CHROMA-G
LUMINANCE
Switches from the green component of video on cross fader side [A] to the
video on side [B].
Switches from the dark portion of video on cross fader side [A] to the video
on side [B].
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
USING THE EFFECT FUNCTION
This function applies effects to the selected channel’s sound and video. Effects include BEAT effects, which are applied in linkage to the
track’s BPM; TOUCH effects, which control effects by directly touching the screen; and TEXT effects, which display onscreen characters
with effects added in rhythm to the track. The UTILITY (MASTER MONITOR) button can be pressed to display the master monitor’s image
on the LCD screen.
When master monitor is on
UTILITY
(MASTER MONITOR) CH SELECT
3
4
USB
1
HI
VIDEO FX
PATTERN
0
1
9
9
2
5
6
8
7
6
5
4
3
8
7
6
5
4
3
TAP
EFFECT
ON/OFF
1
0
1
0
7
11
8
9
10
USING BEAT EFFECTS
BEAT effects can be instantaneously set in-sync with the BPM
(Beat Per Minute) of the track, enabling you to apply various
effects to the rhythm even during live performances.
When master monitor is off
1
Effect category Selects the category of effects you wish to
apply. Select from [BEAT] (red), [TOUCH]
buttons
4
(blue), and [TEXT] (green).
2
3
4
Effect select
buttons
Select and touch the desired effect button
1
from the 12 BEAT effects.
MASTER
monitor
When master monitor is on, displays
master output.
2
Channel select
display
Rotate the CH SELECT dial to select the
channel to which you wish to apply the
effect.
11
5
6
5
Effect mode
select buttons
A: Touch to apply the effect to audio only.
AV: Touch to apply the effect to both
audio and video.
7
V: Touch to apply the effect to video only.
8
9
6
7
Video EFFECT
monitor
Monitors effect results.
Video effect
pattern display
Rotate the VIDEO FX PATTERN/TEXT
BANK dial to select the video effect
pattern. When BEAT effect is enabled, you
can choose from
10
[ORIGINAL]/[INVERSE]/[EDGE]/[HUE].
8
9
[BPM
AUTO/TAP]
button
Touch to switch the measurement
method of the BPM between AUTO and
TAP.
BPM/parameter Displays the measured BPM and effect
display
parameters.
10 Beat button
Touch to select the multiplication factor
of the beat calculated from the BPM for
synchronization of effects.
11 [VISUALIZER]
button
Allows use of images produced internally
by the unit.
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
1
Touch the [BPM AUTO/TAP] button to select the BPM (=Beat
Per Minute) measurement mode.
AUTO: The BPM is automatically measured from the input
music signal.
TAP: Tap the TAP button with your finger to manually input the
BPM.
• Whenever power is first turned ON, [AUTO] is selected by
default.
• The selected mode ([AUTO]/[TAP]) will appear in the
display.
• When a BPM cannot be measured automatically, the BPM
display in the display will flash.
• The measurement range of AUTO mode is BPM=70 to 180.
Depending on the track, the BPM may not be accurately
measured. In these cases, use TAP mode to manually enter
the BPM.
7
Set the EFFECT ON/OFF button to ON to apply the effect.
• Each time the button is pressed it will switch between ON
and OFF (whenever power is first turned ON, the setting
defaults to OFF).
• When effect is ON, the button flashes.
Video effect pattern
Rotate the VIDEO FX PATTERN/TEXT BANK dial to select a video
effect pattern for the selected video effect.
For descriptions on the video effect pattern change caused by
rotating the VIDEO FX PATTERN/TEXT BANK dial, refer to P. 24.
Parameter 1
Rotate the TIME/PARAMETER dial to adjust temporal parameters
of the selected effect.
For descriptions on the changes in parameter 1 caused by turning
the TIME/PARAMETER dial, refer to P. 23.
[Manually entering the BPM using the TAP button]
Parameter 2
When the TAP button is tapped to the beat (a quarter note) more
Rotate the LEVEL/DEPTH dial to adjust quantitative parameters of
the selected effect.
For descriptions on the changes in parameter 2 caused by rotating
the LEVEL/DEPTH dial, refer to P. 23.
than twice, the average length will be set as the BPM.
• Pressing the TAP button during [AUTO] mode will switch the
BPM measurement mode to [TAP], and the length between the
taps will be measured.
• When a BPM is set using the TAP button, the multiplication
factor will become [1/1] or [4/1] (depending on the effect), and
the effect time will be set to either the length of 1 beat (a quarter
note) or 4 beats.
• Rotate the TIME/PARAMETER dial while pressing the TAP
button to set the BPM directly.
Using the visualizer
This function allows the use of images produced internally by the
unit.
1
Set [VISUALIZER] button to [ON].
The video effect monitor displays the image.
2
3
Use the effect select buttons to choose a desired image.
• Touch the [BPM AUTO/TAP] button to return to [AUTO] mode.
Use the CH SELECT dial to select the desired channel.
2
Touch the effect category button [BEAT].
• The image will move automatically in rhythm to the music’s
• The [BEAT] button will light brightly, and the icon will move
beat.
as an animation.
• In the event no input image is present, the visualizer’s image
can be used.
• The BEAT effect screen will be displayed.
• Whenever power is first turned ON, the [BEAT] effect is
selected by default.
3
4
Use the effect select buttons to select an effect type.
• The selected button will appear white, and the icon will move
as an animation.
• For a description of each effect, refer to P. 23.
Use the CH SELECT dial to select the channel to which you
wish to apply the effect.
• The selected effect channel display will appear white.
• If [MIC] is selected, the audio effect will be applied to both
MIC 1 and MIC 2. There will be no effect on the video.
• When turning the power ON, [MASTER] will be selected.
5
6
Touch the effect mode select button to select the effect
mode.
• The selected button will appear white, and the icon will move
as an animation.
A: The effect will be applied to the audio only.
AV: The effect will be applied to both the audio and video.
V: The effect will be applied to the video only.
• When turning the power ON, [AV] will be selected.
Touch the beat button to choose the multiplication factor of
the beat for synchronization of the effect.
• Select the beat number calculated from the BPM.
• The selected beat button will be highlighted.
• An effect time that corresponds to the multiplication factor
of the beat will be automatically set.
[Example] When BPM=120
1/1 = 500 ms
1/2 = 250 ms
2/1 = 1000 ms
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
USING TOUCH EFFECTS
6
7
[HOLD] button When [HOLD] button is set to [ON],
effects are recorded from the time the
screen is touched until the finger is
removed.
With TOUCH effects, many effects can be created by touching the
video EFFECT performance monitor.
[VISUALIZER]
button
Internally creates a video image to which
TOUCH effects can be applied.
When master monitor is off
1
Touch the effect category button [TOUCH].
• The [TOUCH] button will light brightly, and the icon will
move as an animation.
• The TOUCH effect screen will be displayed.
Select an effect from the effect select buttons.
1
2
3
• The selected button will appear white, and the icon will move
as an animation.
• For a description of each effect, refer to P. 25.
6
7
4
Use the CH SELECT dial to select the channel to which you
wish to apply the effect.
• The selected effect channel display will appear white.
• If [MIC] is selected, the audio effect will be applied to both
MIC 1 and MIC 2. There will be no effect on the video.
Touch the effect mode select button to select the effect
mode.
2
3
5
4
• The selected button will appear white, and the icon will move
as an animation.
A: The effect will be applied to the audio only.
AV: The effect will be applied to both the audio and video.
V: The effect will be applied to the video only.
• When turning the power ON, [AV] will be selected.
Set the EFFECT ON/OFF button to ON to apply the effect.
• Each time the button is pressed it will switch between ON
and OFF (whenever power is first turned ON, the setting
defaults to OFF).
• When effect is ON, the button flashes.
Touch the video effect performance monitor to change the
effects.
When master monitor is on
5
6
• When [HOLD] button is set to [ON], effects are recorded
from the time the screen is touched until the finger is
removed (max. 8 sec.), then output repeatedly.
• Each time the [HOLD] button is touched it will switch
between [ON] and [OFF].
1
4
5
7
• Whenever power is first turned ON, the setting defaults to
[OFF].
2
6
3
Pattern
Rotate the VIDEO FX PATTERN/TEXT BANK dial to select a video
effect pattern of the selected video effect.
For descriptions of the video pattern changes caused by rotating
the VIDEO FX PATTERN/TEXT BANK dial, refer to P. 25.
Parameter 1
1
2
Effect select
buttons
Select and touch the desired effect button
Rotate the TIME/PARAMETER dial to adjust the parameters for
the selected effect.
For descriptions on the changes in parameter 1 caused by rotating
the TIME/PARAMETER dial, refer to P. 25.
from the 12 TOUCH effects.
Effect mode
select buttons
A: Touch to apply the effect to audio only.
AV: Touch to apply the effect to both
audio and video.
Parameter 2
V: Touch to apply the effect to video only.
Rotate the LEVEL/DEPTH dial to adjust the quantitative
3
4
Video EFFECT
performance
monitor
Touch here to apply effects to the video
parameters for the selected effect.
image.
For descriptions on the changes in parameter 2 caused by rotating
the LEVEL/DEPTH dial, refer to P. 25.
Rotate the VIDEO FX PATTERN/TEXT
BANK dial to select the video effect
pattern. The pattern will differ depending
on the effect type.
Video effect
pattern display
Using the Visualizer
This function allows the use of images produced internally by the
unit.
5
Parameter
display
Displays the TOUCH effect parameter.
The parameter will differ depending on
the effect type
1
Set [VISUALIZER] button to [ON].
The video effect performance monitor displays the image.
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
2
3
4
Use the effect select buttons to choose a desired image.
Touch the image to apply changes.
5
6
7
Video EFFECT
monitor
Monitors the TEXT effects.
Use the CH SELECT dial to select the desired channel.
• In the event no input image is present, the visualizer’s image
can be used.
[TEXT EDIT]
button
Touch to edit the text of the selected
[TEXT BANK] button.
[BPM
AUTO/TAP]
button
Touch to switch the measurement
method of the BPM between AUTO and
TAP. Pressing the TAP button will also
switch this to TAP.
USING TEXT EFFECTS
TEXT effects can be instantaneously set in-sync with the BPM
(Beat Per Minute) of the track, enabling you to apply various TEXT
effects to the rhythm.
8
9
Parameter
display
Displays the measured BPM and effect
parameters.
Beat
button/beat
display
Touch to select the multiplication factor
of the beat calculated from the BPM for
synchronization of effects.
When master monitor is off
1
Touch the [BPM AUTO/TAP] button to select the BPM (=Beat
Per Minute) measurement mode.
1
2
AUTO: The BPM is automatically measured from the input
3
music signal.
TAP: Tap the TAP button with your finger to manually input the
BPM.
• Whenever power is first turned ON, [AUTO] is selected by
default.
• The selected mode ([AUTO]/[TAP]) will appear in the
display.
• When a BPM cannot be measured automatically, the BPM
display in the display will flash.
6
4
3
5
• The measurement range of AUTO mode is BPM=70 to 180.
Depending on the track, the BPM may not be accurately
measured. In these cases, use TAP mode to manually input
the BPM.
7
8
2
3
4
Touch the effect category button [TEXT].
9
• The [TEXT] button will light brightly, and the icon will move
as an animation.
• The TEXT effect screen will be displayed.
When master monitor is on
Select a text effect using the effect select buttons.
• The selected button will appear white, and the icon will move
as an animation.
• For a description of each effect, refer to P. 30.
Choose a text from TEXT BANK.
• Rotate the VIDEO FX PATTERN/TEXT BANK dial to select
TEXT BANK and touch the [TEXT BANK] button to select the
text.
• The selected button will appear white.
Use the CH SELECT dial to select the channel to which you
wish to apply the effect.
• The selected effect channel display will be highlighted.
• TEXT effects are not supported when [MIC] is selected.
Effects are applied to audio only.
Touch the effect mode select buttons to choose the effect
mode.
1
2
5
6
3
6
4
5
7
8
9
• The selected button will be highlighted and an animation
will appear.
A: An effect will be applied to the audio only.
AV: An effect will be applied to both the audio and video.
V: An effect will be applied to the video only.
• When turning the power ON, [AV] will be selected.
1
2
3
Effect select
buttons
Select and touch the desired effect button
from the 6 TEXT effects.
[TEXT BANK]
buttons
Touch the text button of your choice from
the 6 texts.
TEXT BANK
display
Rotate the VIDEO FX PATTERN/TEXT
BANK dial to select a TEXT BANK from
the 10 available.
4
Effect mode
select button
A: Touch to apply the effect to audio only.
AV: Touch to apply the effect to both
audio and video.
V: Touch to apply the effect to video only.
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
7
Touch the beat button to choose the multiplication factor of
the beat for synchronization of the effect.
• Select the beat number calculated from the BPM.
• The selected beat button will be highlighted.
• An effect time that corresponds to the multiplication factor
of the beat will be automatically set.
[Example] When BPM=120
1/1 = 500 ms
1/2 = 250 ms
2/1 = 1000 ms
8
Set the effect EFFECT ON/OFF button to ON to apply the
effect.
• Each time the button is pressed it will switch between ON
and OFF (whenever power is first turned ON, the setting
defaults to OFF).
• When effect is ON, the button is flashes.
Text bank
Rotate the VIDEO FX PATTERN/TEXT BANK dial to select a TEXT
BANK.
Parameter 1
Rotate the TIME/PARAMETER dial to adjust temporal parameters
of the selected effect.
For descriptions on the changes in parameter 1 caused by rotating
the TIME/PARAMETER dial, refer to P. 30.
Parameter 2
Rotate the LEVEL/DEPTH dial to adjust quantitative parameters of
the selected effect.
For descriptions on the changes in parameter 2 caused by rotating
the LEVEL/DEPTH dial, refer to P. 30.
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
EDITING TEXT
18 [DELETE] button Touch to delete entered text. The text
behind the cursor will be deleted. Hold
depressed to delete all text.
5 4 3 2
19 [BACK SPACE]
button
Touch to delete entered text. The text
before the cursor will be deleted.
1
6
7
8
9
20 Text input
button
Touch to enter text.
1
Touch the [TEXT EDIT] button.
• The TEXT EDIT screen appears.
13
16
17
• Touch the [EXIT] button to return to the TEXT effect screen.
Rotate the VIDEO FX PATTERN/TEXT BANK dial to select TEXT
BANK and touch the [TEXT BANK] button to select the text
you wish to edit.
2
10 11
12
15
18
• The selected button will be highlighted.
• If the [TEXT BANK] button is touched, the text will appear in
the TEXT BOX.
19
14
3
4
5
Touch the [FONT] button to change the font of the text.
• The font will change each time the button is touched. The
font alternates between six different fonts.
Touch the [COLOR] button to change the text color.
• The color changes each time the button is touched. The
color alternates between eight different colors.
Touch the [SIZE] button to change the text size.
• The size changes each time the button is touched. The size
alternates between four different sizes.
20
1
[EXIT] button
Touch to exit the TEXT EDIT screen and
return to the TEXT effect screen.
• Under some conditions, [AUTO SIZE] and [BIG] settings will
produce the same sized images.
Touch the character button to change the text character.
• The character changes each time the button is touched. The
character alternates between five different characters.
• For the character, refer to P. 30
Touch the justify button to change the justification of the
text.
• The justification changes each time the button is touched.
The justification alternates between three different
justifications.
Touch the text type select button to change the text type of
the text.
• The selected button will be highlighted.
• Touch the caps button to switch between upper case and
lower case.
Touch the text input button to enter text.
• The entered text will appear in the text box.
• A maximum of 50 letters can be entered.
2
[FACTORYTEXT] Touch to load factory text data.
button
6
7
3
4
[LOAD] button Touch to load text data from an SD card.
[SAVE] button
Text entered into the TEXT BANK can be
saved to an SD card.
5
TEXT BANK
display
Rotate the VIDEO FX PATTERN/TEXT
BANK dial to select a TEXT BANK you
wish to edit from the 10 available.
6
7
[TEXT BANK]
buttons
Entered text can be stored.
Also touch to call up stored text.
8
9
[FONT] button
Touch to change the font of the text. The
font alternates each time the button is
touched.
8
9
[COLOR] button Touch to change the color of the entered
text. The color alternates each time the
button is touched.
10 Touch the [EXIT] button to finish text edit.
• Text can be edited in real time.
[SIZE] button
Touch to change the size of the entered
text. The size alternates each time the
button is touched.
• When power is turned off, settings return to default values.
SAVE/LOAD
10 Character
button
Touch to change the character of the
input text. The character alternates each
time the button is touched.
• TEXT BANK can be saved to SD card. TEXT BANK saved on an
SD card can also be loaded.
• The [LOAD] button and [SAVE] button will not be displayed if no
SD card is detected.
11 Justify button
Touch to justify the text to the left, center,
or right. The justification alternates each
time the button is touched.
USB keyboard
A USB keyboard can be connected to the USB port to allow text to
be entered directly from the keyboard.
12 TEXT BOX
Displays the entered text.
13 TEXT effect
monitor
The TEXT effect is monitored here.
For the encoding setting of the keyboard, refer to P. 41.
14 Text type select Use to change the text type.
buttons
DISPLAYING/HIDING THE MASTER MONITOR
1
Press the UTILITY (MASTER MONITOR) button.
Each time the button is pressed, the master monitor display
alternates ON/OFF.
15 [CAPS] / [PAGE] Touch to alternate between upper and
lower case, and between page display for
page 1 and 2.
button
• When the master monitor is set to display, the master
monitor will appear in the center display, and the content of
the master output video can be observed.
16 Cursor move
button (<, >)
Touch to move the cursor.
• Whenever power is first turned ON, the master monitor
17 Line break
button (LF)
Touch to create a line break in the text.
defaults to OFF.
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
EFFECT LIST
BEAT effects (*1)
Parameter 1
(TIME/PARAMETER)
Parameter 2
(LEVEL/DEPTH)
Description of the effect
Beat button parameter
Description
Description
Repeat sound will be output For the time of 1 BPM beat, a 1/4 to Sets delay time.
once to the beat. 8/1 delay time will be set.
1 to 4 000
(ms) (*3)
Sets the balance between the
original sound and the delay
sound.
Repeat video will be output For the time of 1 BPM beat, a 1/4 to Sets delay time.
once to the beat. 8/1 delay time will be set.
Sets the balance between the
original video and the delay
video.
Sound will be output several For the time of 1 BPM beat, a 1/4 to Sets delay time.
times to the beat as it
attenuates.
1 to 4 000
(ms) (*3)
Sets the balance between the
original sound and the echo
sound.
8/1 delay time will be set.
Video will be output several For the time of 1 BPM beat, a 1/4 to Sets delay time.
times to the beat as it
attenuates.
Sets the balance between the
original video and the echo
video.
8/1 delay time will be set.
Sound sways right and left to For the time of 1 BPM beat, a 1/8 to Sets effect time.
the beat. 8/1 sway time (for audio) will be set.
10 to 16 000 Sets the balance between the
(ms)
original sound and the effect
sound.
Video sways right and left to For the time of 1 BPM beat, a 1/8 to Sets effect time.
the beat. 8/1 sway time (for video) will be set.
Sets the balance between the
original video and the effect
video.
Sound is cut off to the beat. For the time of 1 BPM beat, a 1/8 to Sets effect time.
10 to 16 000 Sets the balance between the
8/1 cut time will be set.
(ms) (*4)
original sound and the effect
sound.
Video is cut off to the beat.
For the time of 1 BPM beat, a 1/8 to Sets effect time.
8/1 cut time will be set.
Sets the balance between the
original video and the effect
video.
Dramatically changes the
For the time of 1 BPM beat, a 1/2 to Sets the cycle in
10 to 32 000 The effect is enhanced as the
sound tone by moving the
32/1 time will be set for the cycle in which the cutoff
(ms)
dial is rotated to the right.
cutoff frequency of the filter which the cutoff frequency is moved. frequency moves.
in rhythm to the beat.
Outputs an opaque video to For the time of 1 BPM beat, a 1/2 to Sets the cycle in
Sets the balance between the
original video and the effect
video.
the beat.
32/1 time will be set for the cycle in which the opaque
which the opaque filter is applied. filter is applied.
One Flanger effect cycle is
For the time of 1 BPM beat, a 1/2 to Sets the interval in 10 to 32 000 The effect is enhanced as the
quickly and simply created to 32/1 time will be set for the interval in which the flanger (ms)
dial is rotated to the right. Only
the original sound will be
output when the dial is rotated
completely to the left.
the beat.
which the flanger effect is moved.
effect moves.
An enlarged image of the
For the time of 1 BPM beat, 1/2 to 32/1 Sets the interval in
Sets the balance between the
original video and the effect
video.
contour of the video is output time will be set for the interval in
which the effect
to the beat.
which the effect screen appears.
screen appears.
One cycle of phaser effect is For the time of 1 BPM beat, a 1/2 to Sets the interval in 10 to 32 000 The effect is enhanced as the
quickly and simply created to 32/1 time will be set for the interval in which the phaser (ms)
dial is rotated to the right. Only
the original sound will be
output when the dial is rotated
completely to the left.
the beat.
which the phaser effect is moved.
effect moves.
An rotating image of the
For the time of 1 BPM beat, 1/2 to 32/1 Sets the interval in
Sets the balance between the
original video and the effect
video.
contour of the video will be time will be set for the interval in
which the effect
output to the beat.
which the effect screen appears.
screen appears.
Reverberation effect.
Sets the degree of the reverberation Sets the degree of 1 to 100 (%) Sets the balance between the
from between 10 % and 90 %.
the reverberation.
original sound and the effect
sound.
Video with an afterimage will Sets the degree of the afterimage
be output. from between 10 % and 90 %.
Sets the degree of
the afterimage.
Sets the balance between the
original video and the effect
video.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
Parameter 1
(TIME/PARAMETER)
Parameter 2
(LEVEL/DEPTH)
Description of the effect
Beat button parameter
Description
Description
The input sound is given an Sets the effect of the robotic sound Sets the effect of
–100 to 100 The effect is enhanced as the
effect like that created by a pitch between –100 % and 100 %
the robotic sound (%)
pitch.
dial is rotated to the right.
robot.
A robot-like video is created Sets the ratio of the mix between the Sets the ratio of the
The up and down swinging is
enhanced as the dial is rotated
to the right.
by swinging the image up
and down and applying a
mosaic filter.
mosaic size and the original video
mix between the
mosaic size and
the original video.
between –100 % and 100 %
An expansive sound as if
various sources were
emitting the same sound
pitch.
For the time of 1 BPM beat, a 1/2 to Sets the interval in 10 to 32 000 Sets the balance between the
32/1 time will be set for the interval of which the chorus (ms)
original sound and the chorus
the vibrato of the chorus sound.
sound is
modulated.
sound.
A video divided into RGB
For the time of 1 BPM beat, a 1/2 to Sets the interval in
Sets the balance between the
original video and the effect
video.
components is output to the 32/1 time will be set for the interval in which the image
beat.
which the image returns to the
returns to its
original.
original.
Records and repetitively
outputs the beat sound.
For the time of 1 BPM beat, a 1/8 to Sets effect time.
8/1 effect time is be set.
10 to 4 000
(ms) (*3)
Sets the balance between the
original sound and the ROLL
sound.
Records and repetitively
outputs the beat image.
For the time of 1 BPM beat, a 1/8 to Sets the time in
Sets the balance between the
original video and the effect
video.
8/1 effect time is be set.
which the image is
repeated.
Records and repetitively
outputs the beat sound in
reverse.
For the time of 1 BPM beat, a 1/8 to Sets effect time.
8/1 effect time is be set.
10 to 4 000
(ms) (*3)
Sets the balance between the
original sound and the ROLL
sound.
Records and repetitively
outputs the beat video in
reverse.
For the time of 1 BPM beat, a 1/8 to Sets the time in
Sets the balance between the
original video and the effect
video.
8/1 effect time is be set.
which the image is
repeated.
(*1) When the effect channel display shows [CFA], [CFB], or [MST]/[MASTER], even if the effect monitor is turned ON, if the selected
channel’s sound is not output to the master output, the effect sound will not be heard.
(*2) If effect is set to OFF, the effect sound will not be audible when monitoring effects.
(*3) The shortest video effect time value is: For NTSC, 66 ms. For PAL, 80 ms.
(*4) The shortest video effect time value is: For NTSC, 99 ms. For PAL, 119 ms.
(*5) When the visualizer function is switched from ON to OFF, the visualizer’s image will be subjected to ROLL in the sampling state.
(*6) When effects are set to OFF, images with effects applied will not be displayed on the video effects monitor.
(*7) Effects will be disabled in all channels if copy-protected contents are input to any channel. In other words, in this case effects will not
function even if non-copy-protected contents are input to the channel to which you wish to apply effects.
Video effect pattern
No. Name
Description of video effect pattern
Original image without video effect pattern.
Inverts brightness.
1
2
3
4
ORIGINAL
INVERSE
EDGE
Creates a border around the image.
Changes the color (except black and white).
HUE
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
TOUCH effects (*1)
Parameter 1
(TIME/PARAMETER)
Parameter 2
(LEVEL/DEPTH)
Description of the effect
Description of the effect when
touched
Description
Description
AUDIO
Phasing effect is applied
proportional to the volume of
the input bass sound.
Touch the screen toward the right to
enhance the effect. Touch toward
the left to reduce the effect.
–
–
Rotate the dial
clockwise to enhance
the effect. When dial is
rotated fully
counterclockwise, only
original sound is
output.
VIDEO
Outputs an effect in which ripples spread from the point being touched.
Continuously outputs five
Outputs an effect in which ripples
spread from the point being
touched.
Sets the strength 1 to 10 Sets the balance
PATTERN1
ripples.
(the amplitude) of
between the original
video and the effect
video.
the ripples.
Continuously outputs seven
ripple designs (shifts in the
brightness).
PATTERN2
Outputs curtain-like ripples.
PATTERN3
PATTERN4
Continuously outputs three
large ripples.
AUDIO
(*4)
Outputs a reverberation effect. Touch the screen toward the right to
enhance the effect. Touch toward
–
–
Sets the balance
between the original
sound and the effect
sound.
the left to reduce the effect.
VIDEO
Outputs a magnified or reduced-size image.
Outputs an image zoomed in on Outputs an image zoomed in on the Sets the scale of
1 to 10 Sets the balance
between the original
video and the effect
video.
PATTERN1
the point touched.
point touched.
magnification/redu
ction.
Outputs an image stretched
horizontally from the point
touched.
Outputs an image stretched
horizontally from the point touched.
PATTERN2
PATTERN3
PATTERN4
Outputs an image stretched
vertically from the point
touched.
Outputs an image stretched
vertically from the point touched.
Outputs an image zoomed out Outputs an image zoomed out from
from the point touched. the point touched.
AUDIO
Outputs a sound with the cutoff frequency of the filter changed.
Outputs a sound through a low- Touch the screen toward the right to
–
–
–
–
–
–
–
–
–
PATTERN1
PATTERN2
PATTERN3
PATTERN4
pass filter.
enhance the effect. Touch toward
the left to reduce the effect.
Outputs a sound through a
high-pass filter.
Touch the screen toward the right to
enhance the effect. Touch toward
the left to reduce the effect.
Outputs a sound through a
band-pass filter.
Touch the screen toward the right to
enhance the effect. Touch toward
the left to reduce the effect.
Outputs a sound through a
notch filter.
Touch the screen toward the right to
enhance the effect. Touch toward
the left to reduce the effect.
VIDEO
Outputs a blurred image.
Outputs an image with blur
Touch more toward the right to
Sets color when
1 to 10 Sets the balance
between the original
video and the effect
video.
PATTERN1
PATTERN2
PATTERN3
PATTERN4
toward the left side.
enhance the blurred effect on the left blur effect is
side.
applied.
Outputs an image with blur
toward the right side.
Touch more toward the right to
enhance the blurred effect on the
right side.
Outputs an image with blur
toward the bottom side.
Touch more toward the right to
enhance the blurred effect on the
bottom side.
Outputs an image with blur
toward the top side.
Touch more toward the right to
enhance the out-of-focus effect on
the top side.
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
Parameter 1
(TIME/PARAMETER)
Parameter 2
(LEVEL/DEPTH)
Description of the effect
Description of the effect when
touched
Description
Description
AUDIO
(*4)
Outputs a phaser effect with
reverberation.
Touch more toward the right to
increase the length of the phaser
effect cycle. Touch toward the left for
shorter cycle length.
–
–
Sets the balance
between the original
sound and the effect
sound.
VIDEO
Outputs an image with a warping effect.
Outputs an image in which the The warp effect is applied centering Sets the area in
1 to 10 Sets the balance
between the original
video and the effect
video.
PATTERN1
screen warps with the
on the touched point. The longer you which the effect is
appearance of paint mixed with touch the screen, the stronger the applied.
water.
effect becomes.
Outputs an image with effect
applied like pixelation distortion
from the point the screen is
touched.
PATTERN2
Outputs an image with
PATTERN3
PATTERN4
fragmented warp.
Outputs an image with spiral
warp.
AUDIO
Modulates the input sound. The Touch the screen toward the right to
–
–
Sets the balance
between the original
sound and the effect
sound.
bass sound has a metallic
quality.
enhance the effect. Touch toward
the left to reduce the effect.
VIDEO
PATTERN1
Outputs an images lined in blocks.
Outputs an image in which the Outputs an image in which the
Sets the number of 1 to 10 Sets the balance
touched block stretches and
shrinks in the horizontal and
vertical direction.
touched block stretches and shrinks partitions of the
between the original
in the horizontal and vertical
blocks.
video and the effect
video.
direction.
Outputs an image in which the Outputs an image in which the
PATTERN2
touched block stretches and
shrinks in the horizontal
direction.
touched block stretches and shrinks
in the horizontal direction.
Outputs an image in which the Outputs an image in which the
PATTERN3
PATTERN4
touched block stretches and
touched block stretches and shrinks
shrinks in the vertical direction. in the vertical direction.
Outputs an image in which the Outputs an image in which the
touched block changes color. touched block changes color.
AUDIO
Outputs audio as if the input
sound has been crushed.
Touch the screen toward the right to
enhance the effect. Touch toward
the left to reduce the effect.
–
–
Rotate the dial
clockwise to enhance
the effect. When dial is
rotated fully
counterclockwise, only
original sound is
output.
VIDEO
PATTERN1
Outputs an image with a radial concentric effect.
Outputs an image that appears The touched location will have the
like a light shining from behind. central coordinates of the effect.
Sets the color.
1 to 10 Sets the balance
between the original
video and the effect
video.
Outputs an image that spreads
radially.
Sets the opening of
the center.
PATTERN2
PATTERN3
PATTERN4
Outputs an image of circles
spreading concentrically.
Sets the opening of
the center.
Outputs an image combining
PATTERN 2 and PATTERN 3.
Sets the opening of
the center.
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
AUDIO
Outputs the input sound as if it Touch more toward the right to
–
–
Rotate the dial
were being made by a robot.
increase the pitch. Touch toward the
clockwise to enhance
the effect. When dial is
rotated fully
left to lower the pitch.
counterclockwise, only
original sound is
output.
VIDEO
Outputs a kaleidoscope-like effect.
Outputs an image circularly
dividing the screen from the
center of the screen.
When the original image is touched Sets the center
1 to 10 Sets the balance
between the original
video and the effect
video.
PATTERN1
and moved, the screen is divided
angle of the image.
circularly and output.
Outputs an image horizontally When the original image is touched Sets the height of
dividing the screen (vertically
stacked).
PATTERN2
PATTERN3
PATTERN4
and moved, the screen is divided
horizontally (vertically stacked).
the image.
Outputs an image vertically
When the original image is touched Sets the width of
dividing the screen (arranged and moved, the screen is divided
the image.
horizontally).
vertically (arranged horizontally).
Outputs an image divided
horizontally and vertically.
When the image is touched and
moved, the screen is divided
horizontally and vertically.
Sets the width and
height of the
image.
AUDIO
Produces an effect that lowers Touch the screen toward the right to
–
–
Sets the balance
between the original
sound and the effect
sound.
the pitch of the input sound.
enhance the effect. Touch toward
the left to reduce the effect.
VIDEO
PATTERN1
Outputs image with a lens-like effect.
Outputs image with a lens-like The lens moves to the location that is Sets the size of the 1 to 10 Sets the balance
effect.
touched.
lens.
between the original
video and the effect
video.
Outputs image with a lens-like The lens moves to the location that is
PATTERN2
PATTERN3
effect.
touched.
Outputs image with a lens-like The lens moves to the location that is
effect.
touched, and the image within the
lens also moves in accordance with
the amount of lens movement.
Inverts the luminance
The lens moves to the location that is
PATTERN4
components, and outputs the touched.
image with a lens-like effect.
AUDIO
Produces phaser effect. By
moving the touched position
between left and right, the
volume of the effect changes.
Touch the screen toward the right to
–
–
Rotate the dial
enhance the effect. Touch toward
clockwise to enhance
the effect. When dial is
rotated fully
the left to reduce the effect.
counterclockwise, only
original sound is
output.
VIDEO
PATTERN1
Outputs an image formulated as a cube.
Outputs an image of the cube Moves to the touched position.
rotating.
Sets the size of the 1 to 10 Sets the balance
object.
between the original
video and the effect
video.
Outputs an image of a
bottomless pyramid prism
rotating.
PATTERN2
PATTERN3
PATTERN4
Outputs an image of a
bottomless pentagon prism
rotating.
Outputs an image of a
bottomless heptagon prism
rotating.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
Parameter 1
(TIME/PARAMETER)
Parameter 2
(LEVEL/DEPTH)
Description of the effect
Description of the effect when
touched
Description
Description
AUDIO
Flanger effect is applied. Move Touch more toward the right to
–
–
Rotate the dial
finger on touch panel to right- lengthen the cycle of the flanger
clockwise to enhance
the effect. When dial is
rotated fully
left to change effect volume.
effect. Touch toward the left for
shorter effect cycle.
counterclockwise, only
original sound is
output.
VIDEO
Outputs an image with a twisting rotational effect.
Outputs an image in which the The image rotates when you touch Sets the twisting
1 to 10 Sets the balance
PATTERN1
screen twists and rotates.
and drag your finger in a circular
motion around the center of the
screen.
speed.
between the original
video and the effect
video.
When enlarged more
than the center, the
rotating speed
increases.
Outputs an image where the
screen is divided and twisted
individually.
The image rotates when you touch Set the number of
Sets the balance
between the original
video and the effect
video.
PATTERN2
PATTERN3
and drag your finger in a circular
motion around the center of the
screen.
divisions.
When enlarged more
than the center, the
rotating speed
increases.
As in PATTERN2, the screen
image is divided, and in
proportion to the audio level,
the image is stretched and
compressed like a graphic
equalizer effect.
The block of the touched location
will stretch. While touching, the
stretching and shrinking
correspondent to the audio level will
stop.
Set the number of
divisions.
Sets the balance
between the original
video and the effect
video.
When enlarged more
than the center, the
shrinking speed
decreases, and as MAX
is approached,
changes to the reverse,
stretching operation.
Outputs an image where the
screen is twisted and an
afterimage is left.
The image rotates when you touch Sets the twisting
Sets the balance
between the original
video and the effect
video.
PATTERN4
and drag your finger in a circular
motion around the center of the
screen.
speed.
When enlarged more
than the center, the
rotating speed
increases.
AUDIO
Outputs a sound with the cutoff Touch the screen toward the right to
frequency of the filter changed. enhance the effect. Touch toward
the left to reduce the effect.
–
–
Rotate dial clockwiseto
enhance effect.
VIDEO
PATTERN1
Outputs image with a spotlight effect.
Outputs image with a spotlight Outputs an image with a spotlight of Sets the interval in 1 to 10 Sets the balance
of a random size on a random a fixed size on the touched location. which the spotlight
location.
between the original
video and the effect
video.
is updated.
Outputs image with a spotlight Outputs an image with a spotlight of
PATTERN2
PATTERN3
PATTERN4
of a random size on a random a random size on the touched
location.
location.
Outputs an image with a
Outputs an image with a spotlight of
spotlight of a random size and a fixed size and random color on the
color on a random location.
touched location.
Outputs an image with a
Outputs an image with a spotlight of
spotlight of a random size and a random size and color on the
color on a random location.
touched location.
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
AUDIO
Flanger effect is applied. Move Touch more toward right side to
finger on touch panel to right- enhance effect. Touch more toward
left to change effect volume. left side to decrease effect.
–
–
Rotate the dial
clockwise to enhance
the effect. When dial is
rotated fully
counterclockwise, only
original sound is
output.
VIDEO
Outputs an image of a circle with color in motion.
Outputs an image of a circle
The circle moves towards the
touched point.
Sets the size of the 1 to 10 Sets the balance
PATTERN1
with dot designs.
circle.
between the original
video and the effect
video.
Outputs an image of a circle
with border designs.
PATTERN2
PATTERN3
PATTERN4
Outputs an image of a circle
with vertically stretched image.
Outputs an image of a circle
with original image.
(*1) When the [HOLD] button is set to ON, you can record the track of your finger touching the touch panel for a maximum of 8 seconds.
(*2) The effect will not become visible unless the video effect performance monitor is touched.
(*3) When effect is set to ON, random effects are applied.
(*4) When effect is set to OFF, effect sounds cannot be heard even on monitor.
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE EFFECT FUNCTION
TEXT effects
Parameter 1
(TIME/PARAMETER)
Parameter 2 (LEVEL/DEPTH)
Description
Description of the effect
Beat button parameters
Description
Dramatically changes the
sound tone by moving the
frequency of the filter in
rhythm to the beat.
For the time of 1 BPM beat, a 1/2 to Sets the interval for 10 ms to
Rotate dial clockwise to
enhance effect.
32/1 time will be set for the interval in which the cutoff
32 000 ms
which the cutoff frequency is moved. frequency moves.
The text line chips away at
dot block units and then
reconstructs itself at dot
block units.
For the time of 1 BPM beat, a 1/2 to Sets effect time.
32/1 time is set for which the text
Sets the balance between the
original video and the text.
disappears at dot block units and
then reconstructs itself again.
One phaser effect cycle is
For the time of 1 BPM beat, a 1/2 to Sets the interval in 10 ms to
Rotate the dial clockwise to
enhance the effect. When dial
is rotated fully
quickly and simply created to 32/1 time will be set for the interval in which the phaser 32 000 ms
the beat.
which the phaser effect is moved.
effect moves.
counterclockwise, only original
sound is output.
The text line is lines up and For the time of 1 BPM beat, a 1/2 to Sets effect time.
Sets the balance between the
original video and the text.
forms a circle as it rotates.
32/1 time is set for which the text
rotates once.
One Flanger effect cycle is
For the time of 1 BPM beat, a 1/2 to Sets the interval for 10 ms to
Rotate the dial clockwise to
enhance the effect. When dial
is rotated fully
quickly and simply created to 32/1 time is set for the interval in
which the flanger 32 000 ms
the beat.
which the flanger effect is moved.
effect moves.
counterclockwise, only original
sound is output.
The text string will glow and For the time of 1 BPM beat, a 1/2 to Sets effect time.
Sets the balance between the
original video and the text.
stretch out horizontally in a 32/1 time will be set in which the text
linked manner, and then
begins to change and then returns to
return to the original string. its original state again.
Cuts the sound in rhythm to For the time of 1 BPM beat, a 1/8 to Sets effect time.
10 ms to
16 000 ms
Sets the balance between the
original sound and the effect
sound.
the beat.
8/1 cut time will be set.
Random text lines appear.
For the time of 1 BPM beat, a 1/8 to Sets effect time.
8/1 time will be set for appearance of
random text lines.
Sets the balance between the
original video and the text.
Outputs audio in which the For the time of 1 BPM beat, a 1/8 to Sets effect time.
10 ms to
16 000 ms
Sets the balance between the
original sound and the effect
sound.
input sound starts from a
high pitch and returns to its
normal sound.
8/1 effect time will be set.
Beginning from zoom-in on For the time of 1 BPM beat, a 1/8 to Sets effect time.
each individual letter, a text 8/1 time is set for which the letters
string is formed as the letters zoom out to their set positions.
zoom out to their set
Sets the balance between the
original video and the text.
positions.
Outputs audio as if the input For the time of 1 BPM beat, a 1/2 to Sets the interval for 10 ms to
sound has been crushed. 32/1 time will be set for the interval in which the crush 32 000 ms
which the crush effect is moved. effect moves.
Rotate the dial clockwise to
enhance the effect. When dial
is rotated fully
counterclockwise, only original
sound is output.
From the first letter of the text For the time of 1 BPM beat, a 1/2 to Sets effect time.
string, the letters become 32/1 time is set for which the text
stretched from left to right as appears as it is stretched, and then
they appear, and from the
first letter of the text line, the
letters are stretched from
right to left as they disappear.
Sets the balance between the
original video and the text.
disappears as it is stretched.
(*1) Video effects are dependant upon image display timing, with the result that an effect may not appear precisely as intended when the
set time is very short.
Character
No. Name
Description of character
1
2
ORIGINAL
SHADOW
Sets text alone, without reflecting the character.
Applies shadow to displayed text. When COLOR is B/W,
both will have the same effect.
3
4
5
TRANSPARENT Makes text transparent.
OUTSIDE
HUE
Applies border to text.
Changes color of text (except when black and white).
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE JPEG VIEWER
USING THE JPEG VIEWER
JPEG files can be loaded and displayed from USB memory devices and SD cards. Up to eight JPEG files can be loaded.
USB
JPEG VIEWER SETUP
1
Press the JPEG VIEWER button.
The JPEG play mode screen will appear.
HI
7
9
JPEG
VIEWER
1
1
1
9
9
8
7
6
5
4
3
2
1
0
8
7
6
5
4
3
2
1
0
2
3
4
8
SD
CARD
CARD indicator
5
6
BEFORE USING THE JPEG VIEWER
Insert a USB memory device or SD card into this mixer.
Using a USB memory device
Insert a USB memory device containing JPEG files to the USB
connector. Only USB memory devices formatted in FAT32 format
can be used.
Using a SD card
Insert a SD card containing JPEG files into the SD CARD slot.
• The memory card used must be formatted according to “SD
Memory Card Specifications Part2 FILE SYSTEM
SPECIFICATION Version1.0” (SD memory cards are formatted in
the aforementioned standard upon shipping from their
manufacturers). Unformatted memory cards cannot be used.
• Memory cards formatted on computers or digital cameras may
1
[MANUAL
MODE] button
Sets the JPEG play mode to MANUAL.
Sets the JPEG play mode to AUTO.
not operate properly.
• Multi-media cards (MMC) cannot be used.
2
3
4
5
6
[AUTO MODE]
button
• Do not remove the card or turn the power off while the CARD
indicator is blinking (doing so may result in damage to the
stored data).
• Memory cards are delicate electronic devices. Do not bend
them, subject them to strong shocks or impacts. Additionally,
do not use or store memory cards in environments likely to
create static electricity or electrical noise.
• Memory cards may be damaged when exposed to impacts or
static electricity. Handle them with care. It is strongly suggested
that you periodically make copies of important data.
[FADER MODE] Sets the JPEG play mode to FADER.
button
[TIME] display/ When in AUTO mode, sets the time for
Change buttons
changing the JPEG images.
[JPEG BOX]
Selects the JPEG images that are to be
assigned to the channels.
Channel select
buttons
Sets the channel to which JPEG images
are to be assigned.
Alternatively use to cancel the assigned
JPEG.
• Pioneer will not be held responsible for any loss of data or direct/
indirect damages.
7
[JPEG SELECT]
button
Enables JPEG select mode.
If operated when effects are ON, a
warning message will appear and the
screen will not change to the next menu.
8
9
[CLEAR] button Alternates JPEG BOX clear mode ON/
OFF.
[EXIT] button
Exits JPEG viewer setup.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE JPEG VIEWER
Loading JPEG files to the SVM-1000
Use this function to load JPEG files into the JPEG BOX. When
effect is ON, this function is not usable.
Using a JPEG file by assigning it to a channel.
The JPEG play mode includes MANUAL MODE, AUTO MODE, and
FADER MODE, allowing a wide range of performance styles.
1
Touch the [JPEG SELECT] button in the JPEG play mode
screen.
The JPEG select mode screen will appear.
Operating in MANUAL MODE
Assign JPEG image in JPEG BOX as image for designated
channel.
1
2
Touch the [MANUAL MODE] button to select MANUAL mode.
7
2
4
From the JPEG BOX, select the image you wish to assign.
When an image is touched, the border around the image will
change to white.
3
Select the channel to which you wish to assign the image.
Touch the channel select button for the channel you wish to
assign the image to, and the selected image will be displayed
on the channel monitor. In this condition, the JPEG image can
be treated as the input image for that channel.
3
6
1
• When the channel select button is ON, touching one of the
other images in the JPEG BOX will cause the display to
switch instantly to that image.
• When a channel select button is ON, touching one of the
other channel select buttons causes the assigned channel
to be changed instantly.
5
• A JPEG image can be assigned only to one channel selected
with the channel select button.
• If the channel select button is touched again, the
assignment is canceled.
Operating in AUTO MODE
A slide show program can be created in which images in the JPEG
BOX change automatically, and the slide show can be assigned to
a designated channel.
1
2
Touch the [AUTO MODE] button to select AUTO mode.
From the JPEG BOX, select the images you wish to use.
Touch the multiple images you wish to use, and their borders
will turn to white. Touching an image again will deselect it.
3
4
Select the channel to which you wish to assign the images.
Touch the channel select button for the desired channel and
the slide show of selected multiple images will be displayed on
the channel monitor. In this condition, the slide show can be
treated as the input image for that channel.
Use the [TIME] change button to adjust the transition time
for the slide show.
1
Media/folder/
file display
Displays media, files, and folders.
2
3
Address display Displays the address of the media/
folders/files currently being displayed.
Page display/
Page change
buttons
Advances the page display of the
displayed media/folder/file.
4
5
6
7
[BACK] button
Returns to the next higher level of the
folder hierarchy.
[JPEG BOX]
Selects the JPEG BOX into which the
JPEG is to be loaded.
[CLEAR] button Alternates the JPEG BOX clear mode ON/
OFF.
[EXIT] button
Exits JPEG viewer mode and returns to
JPEG play mode.
2
Select a JPEG file you wish to download from the media/
folder/file display.
The media/folder/file display will start from the media used
(USB memory/SD card).
Only JPEG files will be displayed.
Displayable folders and JPEG files are in alphabetical order,
with a maximum 64 folders and 192 files per hierarchical level.
3
4
Touch the [JPEG BOX] to download the file.
Touch the [EXIT] button to end the JPEG viewer mode and
return to JPEG play mode (P. 31).
• When power is turned OFF, JPEG images read into the unit
will be deleted.
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE JPEG VIEWER
Operating in FADER MODE
Using the JPEG images in the JPEG BOX, a slide show can be
created with transitions between images at chosen intervals. The
channel fader for the assigned channel is used to perform the
transitions.
1
2
Touch the [FADER MODE] button to select FADER mode.
Select the images you wish to use from the JPEG BOX.
Touch multiple images on the screen and their borders will
change to white. Touch again to deselect images.
3
4
Select the channel to which you wish to assign the images.
Touch the channel select button for the channel to which you
wish to assign the images, and the image at the upper left of
the group of selected images will be displayed on the channel
monitor.
Operate the fader.
Each time the channel fader for the assigned channel is raised
from the [0] point, the images will change.
Deleting JPEG files downloaded to the JPEG BOX
1
Touch the [CLEAR] button.
The [CLEAR] button will flash.
2
Touch the images on the screen that you wish to delete.
The instant the image is touched, it disappears from the JPEG
BOX. While the [CLEAR] button is flashing, you may continue
by deleting other images if desired.
• This process does not affect file data on attached SD cards
or USB memory devices.
3
Press the [CLEAR] button once again to leave this mode.
• Usable JPEG files have a maximum size of 7 MB or about 12
MP.
• If the original JPEG file does not fit within 640 x 480 pixels,
the file will be automatically resized to 640 x 480 pixels when
downloaded to the SVM-1000.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
THE VIDEO EQUALIZER FUNCTION
THE VIDEO EQUALIZER FUNCTION
Rotating the channel equalizer dial normally applies equalizer effects on audio only. However, by using the VIDEO EQ function, effects
can be applied to video as well.
VIDEO EQ SET UP
Use to make the video effects change
simultaneously when using the equalizer.
OFF: Disables the VIDEO EQ.
VIDEO EQ
HI
R: Used when assigning parameters that
change the red elements of the VIDEO
EQ.
Used when assigning parameters.
1
0
9
8
7
6
5
4
3
2
1
0
G: Used when assigning parameters that
change the green elements of the VIDEO
EQ.
Used when assigning parameters.
B: Used when assigning parameters that
change the blue elements of the VIDEO
EQ.
SET UP THE VIDEO EQ
CONTRAST: Used when assigning
parameters that change the contrast of
the VIDEO EQ.
1
Hold down the VIDEO EQ button.
This initiates the equalizer setup mode.
HUE: Used when assigning parameters
2
Touch each applicable button.
Touch each applicable button on the screen to operate the
VIDEO EQ setup.
• Whenever power is first turned on, default settings are as
follows:
HI: CONTRAST
that change the hue of the VIDEO EQ.
SATURATION: Used when assigning
parameters that change the saturation of
the VIDEO EQ.
3
Touch [EXIT].
MID: HUE
This ends the equalizer setup mode.
LOW: SATURATION
Whenever power is turned OFF, the unit returns to the above
status.
TURNING THE EQUALIZER ON/OFF
• Identical parameter values cannot be allocated to HI, MID
and LOW.
1
Press the VIDEO EQ button.
The VIDEO EQ settings will alternate between enabled/
disabled each time the button is pressed.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
FADER START FUNCTION
FADER START FUNCTION
By connecting the optional Pioneer DJ/VJ DVD Player or DJ CD Player control cable, the channel fader and cross fader can be used to
start DVD/CD playback.
When the mixer’s channel fader lever or cross fader lever are moved, the DVD/CD player is released from the pause mode and
automatically –and instantly – begins playback of the selected track. Also, when the fader lever is returned to its original position, the DVD/
CD player returns to its cue point (back cue), thus allowing “sampler” type play.
Using the Cross Fader to Start Playback
1
Press the FADER START button for the channel (1 to 4)
connected to the DVD/CD player you wish to control.
• The button for the selected channel lights.
Set the CROSS FADER ASSIGN switch for the selected channel
to [A] or [B].
HI
2
• Select [
A
] to assign to cross fader channel A (left side).
CHANNEL
FADER
• Select [B] to assign to cross fader channel B (right side).
FADER
START
0
9
3
4
Move the cross fader lever to the full opposite side away
from the DVD/CD player you wish to start.
8
7
6
5
4
3
2
1
0
Set the DVD/CD player to the desired cue point, and engage
cue point standby.
• If a cue point has already been set, it is not necessary to set
the DVD/CD player to standby at the cue point.
CROSS
FADER
ASSIGN
Cross fader lever (A/B)
5
At the instant you wish to start playback, move the cross
fader lever (A/B).
• DVD/CD player begins playback.
• After playback has begun, if the cross fader lever is moved
fully to the opposite side, the DVD/CD player assigned to the
opposite side channel will return to the cue point and enter
standby mode (back cue).
CROSS FADER START PLAY AND BACK
CUE PLAY
When the DVD/CD player assigned to cross fader channel A is set
to standby at a cue point, moving the cross fader lever from the
right (B) side toward the left (A) side automatically starts play on
the channel A DVD/CD player.
When the cross fader lever reaches the left (A) side, the DVD/CD
player assigned to channel B goes to back cue (returns to cue
point). Also, when the DVD/CD player assigned to channel B is set
to standby at a cue point, moving the cross fader lever from the left
(A) side to the right (B) side automatically starts playback on the
channel B DVD/CD player. When the cross fader lever reaches the
right (B) side, the DVD/CD player assigned to channel A goes to
back cue (returns to cue point).
Using the Channel Fader to Start Playback
1
Press the FADER START button for the channel (1 to 4)
connected to the DVD/CD player you wish to control.
• The button for the selected channel lights.
Set the channel fader lever to [0].
2
3
Set the DVD/CD player to the desired cue point, and engage
cue point standby.
• If a cue point has already been set, it is not necessary to set
the DVD/CD player to standby at the cue point.
4
At the instant you wish to start playback, move the channel
fader lever.
• DVD/CD player begins playback.
• After playback has begun, if the channel fader lever is
returned to the [0] position, the DVD/CD player returns to the
cue point and re-enters standby mode (back cue).
• Playback control is possible with the channel fader only with
the CROSS FADER ASSIGN switch is set to [THRU].
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
PERFORM UTILITY SETUP
Set up MIDI
1
2
3
Hold the UTILITY (SET UP) button depressed.
The MIDI setup mode will be initiated.
Touch [MIDI].
The MIDI setup screen will be displayed.
Touch each applicable button.
Touch each applicable button on the screen to operate the
MIDI setup.
Touch [EXIT].
This will end the MIDI setup mode.
UTILITY
(SET UP)
HI
1
0
9
8
7
6
5
4
3
2
1
0
4
When power is turned OFF, all utility setup values other than MIDI
CHANNEL and KEYBOARD LANGUAGE revert to their default
values.
MIDI SETTINGS
MIDI is an acronym for “Musical Instrument Digital Interface” and
refers to a protocol developed for the exchange of data between
electronic instruments and computers.
A MIDI cable is used to connect components equipped with MIDI
connectors to enable the transmission of data.
The SVM-1000 will use the MIDI function to send operational
information for hardware and BPM (timing clock).
SYNCHRONIZING AUDIO SIGNALS TO
EXTERNAL SEQUENCER, OR USING
SVM-1000 INFORMATION TO OPERATE
AN EXTERNAL SEQUENCER
MIDI OUT
TIMING CLOCK
SYNC.
Alternates MIDI signal output ON/OFF.
Switches the MIDI timing clock
synchronization between start and stop.
SNAP SHOT
Current MIDI information regarding dials
and buttons is transmitted.
1
Connect the DIN connector to a MIDI sequencer, and the USB
port to your computer.
BUTTON TYPE
MIDI CHANNEL
Select the method in which the MIDI
signal is transmitted. Options include
toggle type and trigger type. In the trigger
type, any MIDI codes set to OFF will not be
sent, and MIDI codes set to ON will be
sent each time the button is pressed.
This unit is equipped with both DIN type and USB type output
connectors.
• Supported operating systems include Windows Vista,
Windows XP or Mac OSX.
• For details regarding computer setup, refer to the
instruction manual for your computer and operating system.
For application setup instructions, refer to the instruction
manual for the application involved.
• Set the MIDI sequencer’s synch mode to “Slave”.
• MIDI sequencers that do not support MIDI timing clock
cannot be synchronized.
Changes the MIDI channel. Configures
MIDI channels (1-16) and stores them in
memory.
• Synch may not be achieved if the track’s BPM cannot be
detected and measured stably.
• BPM values set with the TAP mode can also be used to
output the timing clock.
2
Set the MIDI OUT to ON in the MIDI setup.
• The output range of the MIDI timing clock is 40 BPM to 250
BPM.
Note:
The BPM may not be measured correctly with some tracks.
Synchronize the computer application to the audio
signals, or operate the computer application using
the operation data for the SVM-1000.
1
Connect the USB MIDI output connector of the SVM-1000 to
your computer using the USB cable.
• Perform the MIDI settings for the application program. For
further information, refer to the instruction manual for
application program.
• Supported operating systems include Windows XP and Mac
OSX.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
MIDI CODE LIST
MIDI Message
Category
Switch Name
Switch Type
Commnets
MSB
31
01
02
03
04
46
11
41
32
06
07
08
09
47
12
42
33
0C
0E
0F
15
48
13
43
34
50
51
5C
52
49
14
44
0B
5E
5F
LSB
VIDEO TRIM
AUDIO TRIM
HI
VR
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
VR
VR
VR
VR
BTN
VR
SW
VR
VR
VR
VR
VR
BTN
VR
SW
VR
VR
VR
VR
VR
BTN
VR
SW
VR
VR
VR
VR
VR
BTN
VR
SW
VR
SW
SW
MID
CH1
CH2
CH3
CH4
LOW
CUE
OFF=0, ON=127
0 to 127
FADER
CF ASSIGN
VIDEO TRIM
AUDIO TRIM
HI
0, 64, 127
0 to 127
0 to 127
0 to 127
MID
0 to 127
LOW
0 to 127
CUE
OFF=0, ON=127
0 to 127
FADER
CF ASSIGN
VIDEO TRIM
AUDIO TRIM
HI
0, 64, 127
0 to 127
0 to 127
0 to 127
MID
0 to 127
LOW
0 to 127
CUE
OFF=0, ON=127
0 to 127
FADER
CF ASSIGN
VIDEO TRIM
AUDIO TRIM
HI
0, 64, 127
0 to 127
0 to 127
0 to 127
MID
0 to 127
LOW
0 to 127
CUE
OFF=0, ON=127
0 to 127
FADER
CF ASSIGN
CROSS FADER
CH CURVE
CROSS CURVE
0, 64, 127
0 to 127
CROSS FADER
FADER CURVE
0, 64, 127
0, 64, 127
VIDEO MASTER
LEVEL
VR
VR
Bn
Bn
38
18
dd
dd
0 to 127
0 to 127
AUDIO MASTER
LEVEL
MASTER
BALANCE
CUE
VR
Bn
Bn
17
dd
dd
0 to 127
BTN
4A
OFF=0, ON=127
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
MIDI Message
Category
BOOTH
Switch Name
MONITOR
Switch Type
VR
Commnets
0 to 127
MSB
19
LSB
Bn
Bn
Bn
Bn
dd
dd
dd
dd
AUTO/TAP
TAP
BTN
BTN
BTN
SW
45
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
4E
EFFECT CUE
CH SELECT
4B
For CHANNEL SELECT and
VIDEO FX PATTERN, the
logical sum of both values
is sent.
VIDEO FX PATTERN SW
Cn
Bn
pc
EFFECT
PARAMETER 1 value;
FLANGER, PHASER, FILTER,
CHORUS changed to 1/2
value; minus values of
ROBOT are converted to
positive.
TIME/PARAMETER SW
0D
MSB
Bn
2D
LSB
LEVEL/DEPTH
EFFECT ON/OFF
HI
VR
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
Bn
FB
FA
FC
5B
40
1E
1F
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
0 to 127
BTN
VR
OFF=0, ON=127
0 to 127
MIC
LOW
VR
0 to 127
FADER START CH1 BTN
FADER START CH2 BTN
FADER START CH3 BTN
FADER START CH4 BTN
58
59
5A
5D
1B
1A
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0 to 127
(FADER START)
MIXING
LEVEL
VR
VR
(HEAD PHONES)
TIMING CLOCK
MIDI
0 to 127
Timing Clock
START
BTN
BTN
STOP
* The MIDI SNAP SHOT outputs all MIDI commands except MIDI START/STOP.
CENTER PANEL AREA
MIDI Message
Category
Switch Name
Switch Type
BTN
Commnets
MSB
—
LSB
—
UTILITY
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
VIDEO EQ
BTN
BTN
BTN
—
—
JPEG VIEWER
—
—
VIDEO SOLO
MODE
—
—
FADER AV SYNC
BTN
—
—
—
—
—
—
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
GUI BUTTONS
Category
MIDI Message
Switch Name
Switch Type
BTN
Commnets
MSB
—
LSB
BEAT EFFECT
TOUCH EFFECT
TEXT EFFECT
A
—
—
—
—
Changing the category
inevitably causes an effect
program change.
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
—
—
—
—
EFFECT
CATEGORY
—
—
—
AV
—
—
—
V
—
—
—
DELAY
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
41
42
43
44
45
46
47
48
49
4A
4B
4C
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
ECHO
PAN
TRANS
FILTER
FLANGER
PHASER
REVERB
ROBOT
CHORUS
ROLL
BEAT EFFECT
REV ROLL
Beat BUTTON 1
Beat BUTTON 2
Beat BUTTON 3
Beat BUTTON 4
Beat BUTTON 5
Beat BUTTON 6
Beat BUTTON 7
VISUALIZER
BPM AUTO/TAP
RIPPLE
The motion of the TIME/
LSB PARAMETER dial can be
replicated by the button
Bn
0D
MSB
Bn
2D
—
—
—
—
—
—
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
9n
51
52
53
54
55
56
57
58
59
5A
5B
5C
50
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
dd
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
LENS
SPOT
RADIATION
CUBE
BLOCK
KALEIDO
TWIST
ZOOM
TOUCH EFFECT
DROP
BLUR
DISTORTION
HOLD
TOUCH FX
MONITOR X
VR
Bn
1C
dd
0 to 127
0 to 127
TOUCH FX
MONITOR Y
VR
Bn
—
3C
—
dd
—
VISUALIZER
BTN
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
MIDI Message
Category
Switch Name
RANDOM
Switch Type
BTN
Commnets
OFF=0, ON=127
MSB
60
61
62
63
64
65
—
LSB
9n
9n
9n
9n
9n
9n
—
—
—
—
—
—
—
dd
dd
dd
dd
dd
dd
—
ZOOM
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
BLOCK
ROTATION
CRUSH
SLIDE
BANK1
BANK2
—
—
BANK3
—
—
BANK4
—
—
TEXT EFFECT
BANK5
—
—
BANK6
—
—
TEXT EDIT
Beat BUTTON 1
Beat BUTTON 2
Beat BUTTON 3
Beat BUTTON 4
Beat BUTTON 5
Beat BUTTON 6
Beat BUTTON 7
BPM AUTO/TAP
CH1 MONITOR
CH2 MONITOR
CH3 MONITOR
CH4 MONITOR
FADE
—
—
The motion of the TIME/
LSB PARAMETER dial can be
replicated by the button
Bn
0D
MSB
Bn
2D
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BTN
BTN
BTN
BTN
BTN
BTN
BTN
BTN
VR
9n
9n
9n
9n
9n
9n
Bn
Bn
9n
70
71
72
73
74
75
4C
4D
7A
dd
dd
dd
dd
dd
dd
dd
dd
dd
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
OFF=0, ON=127
0 to 127
WIPE
CROSS FADER
SWITCH
CHROMA-B
CHROMA-G
LUMINANCE
TRANS-A
TRANS-B
CROSS FADER
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORM UTILITY SETUP
PERFORM VIDEO MONITOR SETUP
KEYBOARD LANGUAGE SETUP
By connecting a keyboard to the USB connector, text can be
entered through the keyboard during text edit mode (P. 22). Follow
these steps to set up the connected keyboard type.
Set the video monitor output method.
Video monitor setup
1
Hold the UTILITY (SET UP) button depressed.
This will initiate the utility setup mode.
Touch [VIDEO MONITOR].
The video monitor setup screen will be displayed.
• When turning the power ON, [MASTER] will be selected.
Touch each applicable button.
Touch each applicable button on the screen to operate the
video monitor setup.
Keyboard language setup
1
2
3
Hold the UTILITY (SET UP) button depressed.
This initiates the utility setup mode.
Touch [KEYBOARD LANGUAGE].
The keyboard language setup screen will be displayed.
2
3
4
Touch each applicable button.
Touch each applicable button on the screen to perform
keyboard language setup.
Touch [EXIT].
This will end the utility setup mode.
4
Touch [EXIT].
This will end the utility setup mode.
MASTER
MIRROR OF
The master output is sent directly to the
* With keyboards other than those listed, the characters
actually appearing may be different from those pressed.
monitor output.
The master output is flipped horizontally
and sent to the monitor output.
MASTER
MASTER &
CHANNEL
Both master output and channel output
are sent to the monitor output.
CHANNEL
All channels’ outputs are sent to the
monitor output.
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE SETUP
HARDWARE SETUP
POWER
SYSTEM SETTINGS
1
Touch [SYSTEM].
The SYSTEM setting screen will be displayed.
UTILITY
(SET UP)
2
Choose settings by touching [] or [].
HI
1
0
9
8
7
6
5
4
3
2
1
0
The hardware setup values are preserved even when power is
turned OFF.
Initiate hardware setup
1
Turn the POWER switch on while pressing the UTILITY (SET
UP) button.
• Continue depressing the UTILITY (SET UP) button while the
logo mark [PIONEER PRO DJ] is displayed.
• The hardware setup screen will be displayed.
VIDEO SYSTEM
Selects the video signal format. When
used in North America, it should be set to
NTSC (7.5 IRE).
MIC SETTING
1
Touch [MIC]
The MIC setting screen will be displayed.
Choose settings by touching [
DIGITAL OUT MAX Selects the maximum level of the digital
LEVEL out circuit.
2
] or [].
3
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
OUTPUT TO
Set whether or not to output the audio
BOOTH MONITOR from the MIC to the booth monitor.
TALK OVER
THRESHOLD LEVEL
Adjust the sensitivity of talk over.
TALK OVER LEVEL Adjust the level of talk over.
3
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE SETUP
MASTER OUT SETTINGS
MONITOR OUT SETTINGS
1
Touch [MASTER OUT].
1
Touch [MONITOR OUT].
The MASTER OUT setting screen will be displayed.
The MONITOR OUT setting screen will be displayed.
2
Choose settings by touching [
] or [
].
2
Choose settings by touching [] or [].
BRIGHTNESS
CONTRAST
COLOR
Adjusts the brightness of the master output
BRIGHTNESS
CONTRAST
COLOR
Adjusts the brightness of the monitor output.
Adjusts the contrast of the monitor output.
Adjusts the color tone of the monitor output.
Adjusts the saturation of the monitor output.
Adjusts the sharpness of the monitor output.
monitor.
Adjusts the contrast of the master output
monitor.
SATURATION
SHARPNESS
Adjusts the color tone of the master output
monitor.
• Cannot be adjusted when the PAL video
system is used.
• Component outputs cannot be adjusted.
3
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
SATURATION
SHARPNESS
Adjusts the saturation of the master output
monitor.
Adjusts the sharpness of the master output
monitor.
3
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
LCD SETTINGS
1
Touch [LCD].
The LCD setting screen will be displayed.
2
Choose settings by touching [] or [].
BACK LIGHT
Adjust the backlight of the LCD.
3
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE SETUP
4
Touch all [+] marks and make sure the color of the [+] marks
are inverted.
TOUCH PANEL SETTINGS
1
Touch [TOUCH PANEL].
The touch panel setting screen will be displayed.
2
Touch either [TOP PANEL] or [BOTTOM PANEL] to select
settings.
5
Touch [SAVE] to save the settings.
The settings will not be implemented unless [SAVE] is
touched.
TOP PANEL
BOTTOM PANEL
Calibrates the TOP panel.
RETURNING TO DEFAULT SETTINGS
Calibrates the BOTTOM panel.
1
Touch [FACTORY PRESET].
The factory preset screen will be displayed.
Touch to choose either [YES] or [NO].
3
Touch the [+] mark with a pointed object such as a pen.
Use a stylus pen or other type pen without a sharp tip.
2
ENDING HARDWARE SET UP
1
Set the [POWER] switch to OFF.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check
the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in
use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.
Symptom
Possible Cause
Remedy
• Connect to power outlet.
No power.
• The power cord has not been connected.
No sound, or sound volume is • AUDIO INPUT switch is set incorrectly.
too low.
• Set AUDIO INPUT switch to select the currently
playing component.
• Connection cables are not connected properly, • Connect correctly.
or are disconnected.
• Connentors or plugs are dirty.
• Clean away any dirt before connecting.
• The rear panel MASTER ATT. switch is set to
–6 dB, etc.
• Adjust rear panel MASTER ATT. switch.
No microphone sound from
BOOTH output.
• The OUTPUT TO BOOTH MONITOR (P. 42) is set • Set OUTPUT TO BOOTH MONITOR (P. 42) to ON.
to OFF.
No digital output.
• The digital output sampling frequency (fs) does • Set rear panel sampling frequency selector to
not match the specifications of the connected
match the specifications of the connected
component.
component.
Sound is distorted.
• Audio master output level is too high.
• Adjust AUDIO MASTER LEVEL dial or the rear
panel MASTER ATT. switch.
• Input level is too high.
• Adjust the AUDIO TRIM dial so that the input
level approaches 0 dB on the channel level
indicator.
Cross fader doesn’t work.
• CROSS FADER ASSIGN switch setting ([A],
[THRU], [B]) is incorrect.
• Correctly set the CROSS FADER ASSIGN switch
for the desired channel.
Can’t perform fader start with • The FADER START button is set to OFF.
• Set the FADER START button to ON.
• Use a control cable to connect the CONTROL
connectors of mixer and DVD/CD player.
DVD/CD player.
• Rear panel CONTROL connector is not
connected to DVD/CD player.
• Only the rear panel CONTROL connector is
connected to the DVD/CD player.
• Connect both the CONTROL connectors and
analog input connectors.
Effects don’t work.
• Effect channel selecter (CH SELECT) setting is • Correctly select the channel on which you wish
incorrect. to apply effects.
• Effect parameter 2 dial (LEVEL/DEPTH) is set to • Adjust the effect parameter 2 dial (LEVEL/
[MIN].
DEPTH).
BPM can’t be measured.
Measured BPM value is
incorrect.
• Input level is too high, or too low.
• Adjust the AUDIO TRIM dial so that the input
level approaches 0 dB in the channel level
indicator.
• Adjust other channels as well so that the input
levels approach 0 dB in the channel level
indicator.
• BPM may not be correctly measurable with
some tracks.
• Strike the TAP button to set BPM manually.
The measured BPM value is
different from the value
published with the DVD/CD.
• Some differences may occur due to differences • No remedy is necessary.
in BPM detection methods.
MIDI sequencer can’t be
synchronized.
• MIDI sequencer’s synch mode is not set to
“slave”.
• Set MIDI sequencer’s sync mode to “slave”.
• MIDI sequencer is not supported type.
• MIDI sequencers that do not support MIDI
timing clock cannot be synchronized.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Symptom
Possible Cause
• VIDEO INPUT switch is set incorrectly.
Remedy
No video image, or image is
disrupted.
• Set the VIDEO INPUT switch to select the
currently playing component.
• Connection cables are not connected properly, • Connect correctly.
or are disconnected.
• Connectors or plugs are dirty.
• Trim controls are set improperly.
• Clean away any dirt before connecting.
• Adjust trim properly.
• Signal format of the input video source does not • Select the hardware setup’s system settings to
match the system setting selected during
hardware setup.
match the format of the video signal for the
input/output video components.
• The TV monitor’s video signal format does not
match the system setting selected during
hardware setup.
• The TV monitor’s input selector is not set to the • Set the TV monitor’s input selector to the type of
input type actually connected to the unit.
input connected to this unit.
• The TV monitor’s component setting is set to
something besides 525i (interlaced).
• Set the TV monitor’s component setting to 525i
interlaced).
The character pressed on the • The keyboard connected to the USB connector • Set the keyboard language setup to match the
keyboard is not entered.
does not match the setting selected during this
unit’s keyboard language setup.
type of keyboard connected to the USB
connector.
No response when touch panel • Touch panel’s calibration is incorrect.
is touched.
• Set calibration properly in hardware setup’s
touch panel setting.
Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then
on again.
ABOUT THE LCD SCREEN
Regarding Copy Protection
• Some monitors may display so-called “hot pixels” or “dead
pixels” (constantly bright pixels or pixels that are permanently
off). This is a phenomenon characteristic of such displays and is
not considered a malfunction.
Limitation on Effects
If an attempt is made to use DELAY, ECHO, ROLL or REV ROLL
effects with the input of copy-protected contents to any of the
channels, the audio and video will not be subjected to the selected
effect (the function will be disabled even if a non-copy-protected
input is selected in the effect channel).
• When used in cold regions, the screen may appear dark for a
while after the power is first turned on. As the unit warms up
with time, the screen will return to normal brightness.
• Avoid exposing the monitor to direct sunlight, since reflected
light may make the image difficult to view.
Also, even when the input of copy-protected contents is stopped,
and ROLL, REV ROLL effects are once more enabled, the monitor
may display a black screen.
Copy Protected Information Display
In the event copy protected contents are input to a channel, the
channel monitor for that channel will display a message like that
show in Figure 1.
In this event, if DELAY, ECHO, ROLL, or REV ROLL are selected, the
message shown in Figure 2 will be displayed.
ABOUT MINIATURE FLUORESCENT TUBE
TECHNOLOGY
The LCD screen is illuminated by internal miniature fluorescent
tube technology.
• Fluorescent tubes are rated for approximately 10 000 hours of
use (lifetime may be shorter when the unit is used in cold
regions).
• When a fluorescent tube reaches the end of its lifetime, the
screen will become darker, making it difficult or impossible to
see displayed images. In this event, consult your dealer or
service center for repairs.
Fig. 1
Fig. 2
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS
Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 W
Operating temperature . . . . +5 °C to +35 °C (+41 °F to +95 °F)
Operating humidity . . . . . . . . . .5 % to 85 % (without condensation)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.7 kg (28.0 lb)
Maximum dimensions
1
General
4
Input/output connector systems
Audio section
PHONO input connectors
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DVD/LINE input connectors
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DVD input connectors
. . . . . . . . . . . . . . . . . . . . 500 mm (W) x 202.4 mm (H) x 420.6 mm(D)
19.69 in (W) x 7.97 in (H) x 16.56 in (D)
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
LINE input connectors
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MIC input connectors
XLR connector/Phone jack (Ø 6.3 mm) . . . . . . . . . . . . . . . . . . . . 1
Phone jack (Ø 6.3 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DIGITAL coaxial input connectors
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MASTER output connectors
XLR connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
BOOTH output connectors
Phone jack (Ø 6.3 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
REC output connectors
RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DIGITAL coaxial output connector
RCA pin jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PHONES output connector
Stereo phone jack (Ø 6.3 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Video Section
2
Audio section
Sampling rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 kHz
A/D, D/A converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 bits
Frequency response
DVD/LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz to 20 kHz
MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Hz to 20 kHz
PHONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Hz to 20 kHz (RIAA)
S/N ratio (at rated output)
DVD/LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 dB
PHONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 dB
MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 dB
Distortion (LINE-MASTER 1) . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005 %
Standard input level/Input impedance
PHONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –52 dBu/47 kΩ
MIC 1, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –52 dBu/9 kΩ
DVD/LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –12 dBu/22 kΩ
Standard output level/Load impedance/Output impedance
MASTER 1. . . . . . . . . . . . . . . . . . . . . . .+8 dBu/10 kΩ/10 Ω or less
MASTER 2. . . . . . . . . . . . . . . . . . . . . . .+2 dBu/10 kΩ/1 kΩ or less
REC OUT . . . . . . . . . . . . . . . . . . . . . . . . –8 dBu/10 kΩ/1 kΩ or less
BOOTH MONITOR . . . . . . . . . . . . . . .+8 dBu/600 Ω/600 Ω or less
PHONES . . . . . . . . . . . . . . . . . . . . . . . +7.5 dBu/32 Ω/22 Ω or less
Rated output level/Load impedance
DVD input connectors
Composite input, RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VIDEO input connectors
Composite input, RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VIDEO EX input connectors
Composite input, RCA pin jacks . . . . . . . . . . . . . . . . . . . . . . . . . . 2
S-VIDEO input connectors
MASTER 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +26 dBu/10 kΩ
MASTER 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +20 dBu/10 kΩ
Crosstalk (DVD/LINE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 dB
Channel equalizer response
S-Video input, S-connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MASTER output connectors
Component output, BNC connector . . . . . . . . . . . . . . . . . . . . . . . 1
Composite output, BNC connector. . . . . . . . . . . . . . . . . . . . . . . . 1
RCA pin jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
S-Video output, S-connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MONITOR output connectors
Composite output, RCA pin jack . . . . . . . . . . . . . . . . . . . . . . . . . . 1
S-Video output, S-connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OTHER
HI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –26 dB to +6 dB (13 kHz)
MID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –26 dB to +6 dB (1 kHz)
LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –26 dB to +6 dB (70 Hz)
Microphone equalizer response
HI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –12 dB to +12 dB (10 kHz)
LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . –12 dB to +12 dB (100 Hz)
3
Video Section
Input signal. . . . . . . . . . . . . . . . . . . . . . . . . . . NTSC/PAL (selectable)
Sampling rate
. . . . . . . . . . . . . . . . . . . 13.5 MHz, 8 bit, ITU-R BT.656, YCrCb 4:2:2
Input connector (sensitivity/impedance)
Composite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
S (Brightness). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
S (Color) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.286 Vp-p/75 Ω
Video output connector (Level/Impedance)
Composite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
S (Brightness). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
S (Color) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.286 Vp-p/75 Ω
Component Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
Component Cb/Cr . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7 Vp-p/75 Ω
MIDI OUT connector
5P-DIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CONTROL connector
Mini phone jacks (Ø 3.5 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5
Accessories
Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications and appearance are subject to change without
notice.
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA/Aux Etats-Unis
In Canada/Aux Canada
S018_B1_EnFr
Published by Pioneer Corporation.
Copyright © 2007 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
Industrial Products Department: 340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
Printed in Malaysia
<DRB1421-D>
Download from Www.Somanuals.com. All Manuals Search And Download.
|