Pelco Switch c1515m a User Manual

CM6800-48X8

Matrix Switcher/

Controller

Installation/

Operation Manual

C1515M-A (11/01)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION .....................................................................................................................63

OVERVIEW ...............................................................................................................63

OPERATING THE CM6800.......................................................................................63

SWITCH MONITORS........................................................................................63

SELECT CAMERAS .........................................................................................64

CONTROL RECEIVERS ...................................................................................64

OPERATE SEQUENCES..................................................................................65

RUN A MACRO .................................................................................................66

ACKNOWLEDGE AN ALARM...........................................................................67

CALL A PRESET ...............................................................................................67

CREATE AND RUN A PATTERN ......................................................................68

OPERATE AUXILIARIES/RELAYS ...................................................................68

CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER DISPLAYS ... 70

OPERATE SCANNING FUNCTIONS ...............................................................70

DETECT VIDEO LOSS .....................................................................................70

DEFINE ZONES ...............................................................................................70

APPENDIX ........................................................................................................................71

CM6800 DIP SWITCHES..........................................................................................71

MACRO COMMANDS ..............................................................................................72

ASCII OPERATING COMMANDS ............................................................................74

TROUBLESHOOTING ..............................................................................................77

GAINING INITIAL CONTROL ...........................................................................77

SOFTWARE RESET .........................................................................................77

SOLUTIONS TO COMMON PROBLEMS.........................................................78

KBD960/KBR960 ICON/BUTTON LEGEND .............................................................79

GLOSSARY.......................................................................................................................80

SPECIFICATIONS.............................................................................................................84

REGULATORY NOTICES .................................................................................................86

WARRANTY AND RETURN INFORMATION....................................................................86

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF ILLUSTRATIONS

Figure

Page

CM6800 Application ...........................................................................................7

Installing Rack Ears .......................................................................................... 11

Mounting the CM6800 Matrix Switcher/Controller ............................................ 11

CM6800 Video Inputs........................................................................................12

Connecting Terminated Video Sources .............................................................13

Connecting Looping Video Sources ..................................................................13

PTZ Control Connections ..................................................................................14

Connecting Monitors .........................................................................................15

Connecting Alarms ............................................................................................16

Communication Port Connections and RJ-45 Connector Pin-Outs ..................17

CM6800 Communication Port Connections and Options .................................19

Data Cable Plugged into Local Keyboard .........................................................20

Data Cables Plugged into COM 5 and 6 ...........................................................20

Remote Keyboards ...........................................................................................22

RJ-45 Cable Types............................................................................................23

Connecting a KBD960/KBR960 to the CM6800 ...............................................24

Connecting a Single ALM2064 Alarm Interface Unit .........................................25

Connecting a Single REL2064 Relay Interface Unit .........................................26

Connecting Multiple M Devices – Local Connection .........................................27

Connecting Multiple M Devices – Remote Connection .....................................28

PC Connection to DB9 Port ..............................................................................29

PC Connection to RJ-45 Port ............................................................................29

Connecting Genex Multiplexers ........................................................................30

Wiring the AUX 1 and 2 (Relay) Outputs ..........................................................31

Wiring the F3 (TTL) Output ...............................................................................32

CM6800 Time/Date Stamp on Monitor..............................................................33

CM6800 Color Bars ..........................................................................................35

CM6800 Password Screen ...............................................................................37

CM6800 Programming Main Menu ...................................................................37

Access the About CM6800 Screen ...................................................................40

Access the Keyboard to Monitor Access Screen ..............................................40

Access the Camera to Keyboard Access Screen .............................................41

Access the Camera to Monitor Access Screen .................................................41

Access the Internal or External Alarm Screen ..................................................45

Access the Video Loss Screen .........................................................................47

Access the Alarm Group Screen .......................................................................48

Access the Set Auxiliary Screen .......................................................................49

Access the Camera Screen ..............................................................................50

Access the Daily Timer Screen .........................................................................51

Access the Weekly Timer Screen .....................................................................52

Access the Special Timer Screen .....................................................................52

Access the Logical Camera Number Screen ....................................................53

Access the Macro Screen .................................................................................54

Macro Status View Screen ................................................................................55

Access the Monitor Screen ...............................................................................56

Access the Set Password Screen .....................................................................58

Access the Port Screen ....................................................................................59

Access the Priority Screen ................................................................................60

Access the Sequence Screen ...........................................................................61

Access the Scratchpad Sequence Screen ........................................................61

Access the Time and Date Screen ....................................................................62

CM6800 DIP Switches – Factory Default Settings ............................................71

DIP Switch Cover Plate .....................................................................................77

CM6800 DIP Switch 7 .......................................................................................77

Icon/Button Legend ...........................................................................................79

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF TABLES

Table

Page

Video Coaxial Cable Requirements ..................................................................12

Communication Port Devices and Wiring .........................................................18

Default Port Settings .........................................................................................18

Keyboard Addresses: KBD100/200/300 Series Keyboards ..............................21

Switch Settings—KBD200/300 Keyboards Only ...............................................21

Default Port Settings .........................................................................................34

CM6800 DIP Switch Settings ............................................................................71

Macro Commands .............................................................................................72

Examples of ASCII Commands.........................................................................74

ASCII Commands .............................................................................................75

Solutions To Common Problems .......................................................................78

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Read, keep, and follow these instructions.

2. Heed all warnings.

3. There are no user-serviceable parts inside this unit. Only authorized service personnel

may open the unit.

4. Installation and servicing should only be done by qualified service personnel and

conform to all local codes.

5. WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain

or moisture if this unit is designed for indoor use only.

6. Unless this unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P

enclosure, it is designed for indoor use only and it must not be installed where

exposed to rain or moisture.

7. Do not expose this unit to dripping or splashing. Do not place objects filled with liquids,

such as vases, on this unit.

8. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

9. The installation method and materials should be capable of supporting four times the

weight of the unit and equipment.

10. Do not install near any heat source.

11. Only use attachments/accessories specified by the manufacturer.

12. Clean only with dry cloth.

13. Do not defeat the safety purpose of the polarized or grounding-type plug.

14. Protect the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the unit.

15. Unplug this unit during lightning storms or when unused for long periods of time.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous

voltage constituting a risk of electric shock

is present within this unit.

C A U T I O N :

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation

and operation.

FOR QUALIFIED SERVICE PERSONNEL ONLY

1. Only use replacement parts recommended by Pelco.

2. After replacement/repair of this unit’s electrical components, conduct a resistance

measurement between line and exposed parts to verify the exposed parts have not

been connected to line circuitry.

3. CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Battery should only be replaced by authorized service personnel.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

DESCRIPTION

Pelco’s CM6800 Matrix Switcher/Controller is a cross-point video matrix switcher. The

CM6800 provides switching and control for 48 video inputs and eight monitor outputs from

any one of up to 18 keyboards, PCs, and other devices. All 48 video inputs can be used to

control other devices, such as multiplexers. Forty inputs allow for looping to other devices.

The CM6800 can be controlled from a local or remote keyboard, used with a multiplexer to

display multiple camera views on a monitor, and programmed from a personal computer

using the CM6800-MGR software package. The CM6800 can also be controlled with ASCII

commands.

The CM6800 features menu-driven, password-protected programming. Programming can

also be done remotely, with the CM6800-MGR software package. Programming menus are

provided in six languages: English, French, German, Italian, Portuguese, and Spanish.

Multiple ports are provided on the CM6800 for pan/tilt/zoom (PTZ) control, keyboards, and

peripheral components. A single data line can accommodate various types of equipment,

such as external alarm interface units and relay boxes.

ESPRITô

KBD300

CC3500H-2

SPECTRA^Æ

VIDEO TO

SWITCHER

KBD300

SPECTRA^Æ

ALARM

COM

CONTROL

PTZ

OUT

COM

120/230~

50/60 HZ

25 WATTS

ALTERNATE SOURCE INPUTS

VIDEO OUTPUTS

CAMCLOSUREô

SPOT MAIN

AUX

VCR

IN COM OUT

ALARMS

OCC

OUT

110-240V 50/60 Hz

10 11121314 1516

SVHS

GENEX^ÆMULTIPLEXER

WALL

BLOCK

MONITOR

12 VAC

TRANSFORMER

CM9505UPS

KBD960

KBD100

KBD300

KBD200

Figure 1. CM6800 Application

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

KEYBOARDS

Up to 16 keyboards from the KBD100/200/300 Series and 2 keyboards from the KBD960/

KBR960 Series can be connected to the CM6800, allowing monitoring stations that share a

common monitor to each have a keyboard. Camera positioning can be programmed and

controlled from the KBD200/300 and KBD960/KBR960 Series keyboards. Keyboard types

can be mixed in a system. Refer to Associated Equipment for keyboard descriptions.

SEQUENCES, MACROS, PRESETS, PATTERNS, AND ZONES

Special programmed operations include sequences, macros, and camera control, such as

presets, patterns, and zones. All programming (except the scratchpad sequence) is

password-protected.

A sequence allows operators to see a routine of 72 camera views on any system monitor

over and over again. The sequence can be operated automatically or manually. The order

in which the camera views appear and the time each view remains can be programmed.

The CM6800 also provides a scratchpad sequence, which allows a sequence to be run

from an individual monitor. The scratchpad sequence can be accessed without entering the

password-protected programming menus.

A macro is a sequence of commands or steps. When a macro is run, the steps programmed

into that macro are performed. Macros can be operated automatically or manually. Automatic

operation can be based on specific times or dates.

The following operations are available only with positionable cameras:

A preset allows operators to direct a PTZ (camera positioning system) to move to a

predetermined scene on keyboard command or as a result of an alarm. In addition to

moving the camera, a descriptive title can appear on the screen. The number of

presets available is determined by the camera positioning system. (Presets are not

available with the KBD100 keyboard.)

With a pattern operators can program a camera positioning system to move around

its viewing area in a repeating pattern. The number and time length of patterns varies

with different positioning systems. (Patterns are not available with the KBD100

keyboard.)

A zone is a user-defined, physical location to which (1) a label is attached and (2) a

camera is associated. When the associated camera is panned through or remains

within this defined zone, the zone label appears on the monitor. (Zones are not

available with the KBD100 keyboard.)

INTERFACE CONTROL

The CM6800 interfaces with the following:

•

Coaxitron^®standard mode (15-bit) and extended mode (32-bit) protocol receivers

Pelco’s D and P protocol receivers (RS-422)

Pelco’s M protocol devices (RS-485)

PARTIONING AND PRIORITY

The CM6800 provides four ways to partition your system:

•

Camera to Monitor: Cameras can be assigned to specific monitors for viewing.

Keyboard to Monitor: Keyboards can be assigned to control specific monitors.

Camera to Keyboard:

- Viewing: Keyboards can be assigned view-only access to specific cameras (no

PTZ control).

- Control: Keyboards can be assigned PTZ control and viewing access to specific

cameras.

The CM6800 provides eight levels of priority control. Each level defines the ability of a

keyboard to control a camera positioning system and to access programming screens.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARM INPUTS

The CM6800 can accommodate 136 alarm inputs.

Eight internal alarm inputs are provided on the rear panel of the matrix switcher/controller.

These internal alarm inputs are programmable to associate any camera to any input.

The CM6800 provides numerous alarm handling and display options. For example, alarms

can:

•

cause a system monitor display to switch automatically to the camera with the alarm.

activate patterns or go to presets.

operate auxiliary outputs.

Also, up to two ALM2064 Alarm Interface Units can be connected to the CM6800. Each

alarm interface unit can handle up to 64 alarms, for a total of 128 external alarms.

AUXILIARY OUTPUTS

Three internal auxiliary outputs are provided on the back of the CM6800. Two are relay

outputs, and one is an open collector (TTL) output. You can also connect up to two

REL2064 Relay Interface Units for a maximum capacity of 128 auxiliaries.

Auxiliary outputs are activated at the keyboard (except KBD100).

POWER, MOUNTING METHODS

The CM6800 operates on 120V or 230V, 50/60 Hz. The case mounts in three rack units

(5.25 inches or 13.34 cm) of vertical space in a universal mount, such as a 19-inch (48.26

cm) equipment bay, or to a wall or tabletop.

CONTINUOUS OPERATING DEVICE

The CM6800 is a self-contained video surveillance system designed specifically for use in

security applications. As such, the CM6800 is intended for continuous duty operation. Once

installed, there are no user or service technician items that require intervention which would

require the system to go off-line or have the power turned off under normal operation.

There are two methods for system programming: direct menu control and indirect control,

using a Windows^®-based setup program supplied by Pelco. Both of these methods are

noninvasive and do not require the cycling of power in order for storage or execution of new

software settings. The communication ports use standard low voltage interfaces such as

RS-232, RS-422 and RS-485, and all connections and disconnections do not require

rebooting or power cycling. Video connections or changes of termination state do not

require rebooting or power cycling.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MODELS

CM6800-48X8

Matrix switcher/controller with 48 video inputs and 8 monitor outputs,

120/230V, 50/60 Hz

CM6800-48X8-X

Matrix switcher/controller with 48 video inputs and 8 monitor outputs,

120/230V, 50/60 Hz

ASSOCIATED EQUIPMENT

KBD100

KBD200

KBD300

Desktop keyboard with full switching and programming capabilities,

+12 VDC or 12V 50/60 Hz

Desktop keyboard with full switching and programming capabilities,

plus push-button control of PTZ functions, +12 VDC or 12V 50/60 Hz

Desktop keyboard with full switching and programming capabilities,

plus joystick control of PTZ functions, +12 VDC or 12V 50/60 Hz

KBD960

Full-function desktop variable-speed keyboard; 120V, 50/60 Hz

Same as KBD960, PAL-configured for 230V, 50/60 Hz operation

Full-function rack mount variable-speed keyboard; 120V, 50/60 Hz

Same as KBR960, PAL-configured for 230V, 50/60 Hz operation

KBD960-X

KBR960

KBR960-X

KBDKIT

Wiring kit for connecting KBD100, KBD200, and KBD300 keyboards to

remote keyboard port; includes two RJ-45 wall blocks and a

transformer to convert 120V, 60 Hz to 12V, 60 Hz for keyboard power

KBDKIT-X

Wiring kit for connecting KBD100, KBD200, and KBD300 keyboards to

remote keyboard port; includes two RJ-45 wall blocks and a

transformer to convert 230V, 50 Hz to 12V, 50 Hz for keyboard power

CM9505UPS

MX4000

Universal Power Supply for KBD960/KBR960 keyboards

Genex^®Series Multiplexer; available in color or monochrome duplex,

and in color or monochrome simplex

CM9760-CDU-T

Code distribution unit; 16-channel RS-422 transmit only (transmit wire

and ground) distributor; primarily used for connecting up to 16 PTZ

receivers in a “star” or “home run” configuration

ALM2064

Alarm interface unit, provides alarm monitoring capabilities for up to 64

alarm inputs, 100-240V, 50/60 Hz

REL2064

Relay interface unit, provides 64 relays for operating peripheral

equipment, 100-240V, 50/60 Hz

CM9760-MDA

Master distribution amplifier with time, date, and title, 120V, 60 Hz

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Unpack and inspect all parts carefully. The following parts are supplied:

CM6800 Switcher/Controller

10-32 x .750-inch pan head screws

.500” OD nylon washers

NOTE: There are no user-

serviceable parts inside this

unit. Only authorized service

personnel may open the

unit.

Power cord

6-foot (1.8 m) straight data cables with RJ-45 connectors

6-foot (1.8 m) reversed data cable with RJ-45 connectors

RJ-45 wall block terminals

MOUNTING

1. Select a suitable location for the CM6800. It occupies 5.25 inches (13.34 cm) of

vertical space, or three rack units (RUs), in a universal mount. The CM6800 must be

within 6 feet (1.8 m) of a suitable electrical outlet.

Follow proper installation practices and leave 1 RU above and below the

CM6800 for ventilation.

Do not connect the power until the installation is complete. Refer to the System

Start-Up section.

2. The CM6800 is shipped with the rack ears installed at the front. Reposition as needed

for your application. If the ears are not required, remove them.

POSITION BRACKETS FOR

RACK MOUNTING (REAR)

POSITION BRACKETS FOR

UNDER-TABLE MOUNTING

00624

POSITION BRACKETS FOR

RACK MOUNTING (FRONT)

NOTE: EACH CM6800 COMES

WITH 2 RACK EARS

POSITION BRACKETS FOR

FLUSH MOUNTING

(WALL AND TABLE TOP)

Figure 2. Installing Rack Ears

3. Use supplied pan head screws and washers to mount the CM6800 in a standard 19-

inch (48.26 cm) equipment rack or wood or sheet metal screws to mount against a flat

surface, according to your installation requirements.

00615

Figure 3. Mounting the CM6800 Matrix Switcher/Controller

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO SOURCES

The CM6800 offers 48 full-function video inputs which support Coaxitron PTZ control and

video loss detection. Forty video inputs, labeled 1 through 40, can be used for looping

video connections with terminating and unterminating switches on the back panel. The

eight alternate source inputs, labeled 41 through 48, are terminated inputs. They do not

have loop-through connectors or selectable termination switches, but otherwise they offer

the same functionality as video inputs 1 through 40.

All 48 video inputs also provide the ability to view and interface with other devices, such as

Genex multiplexers. If control of the device connected to the video input is required,

connect a data cable between the multiplexer and the CM6800. Refer to the Connecting

Genex Multiplexers section for instructions on connecting and controlling video from a

multiplexer.

00625

Figure 4. CM6800 Video Inputs

1. Connect video cables at the appropriate video input BNC receptacles on the back of

the CM6800. For best results, use crimp-on BNCs only. Do not use screw-on BNCs;

these typically do not provide adequate ground and signal connections.

Refer to Table A for video coaxial wiring requirements.

Table A. Video Coaxial Cable Requirements

Cable Type*

Maximum Distance

RG59/U

RG6/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

RG11/U

* Minimum cable requirements:

75 ohms impedance

All-copper center conductor

All-copper braided shield with 95% braid coverage

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. On video inputs 1 through 40, set the terminating switches according to your system

requirements. Video inputs 41 through 48 cannot be used for loop-through connections.

Terminating switches are used to terminate or unterminate the video input. The factory

default has the switches set in the terminated (75-ohm) position.

If you are connecting only a camera to an input, leave the switch in the terminated

position.

00626

Figure 5. Connecting Terminated Video Sources

If you are looping the input to another device, set the rear panel switch in the

unterminated (Hi-Z) position. Terminate at the final device.

NOTE: The end point of

any video cable run must be

terminated in 75 ohms.

00627

Figure 6. Connecting Looping Video Sources

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL LINES

NOTE: D and P protocol

receivers cannot be mixed

on the same communication

port but you can use D on

one port and P on the other.

You cannot connect a Coaxitron camera to the PTZ-A or PTZ-B ports. If your video sources

are all controlled by Coaxitron, skip this section.

Connect camera control lines to receivers. If any of your video sources are using D or P

protocol via RS-422 communications, they will connect at the PTZ-A and PTZ-B connectors

on the back of the CM6800.

Daisy-chaining (going from one receiver to another) is recommended but not always possible.

A maximum of 16 receivers can be daisy-chained from each port. If more than 32 receivers

are required for your system, or if you do not want to daisy-chain the receiver connections,

use the CM9760-CDU-T. You can connect up to four CM9760-CDU-T units to the

CM6800-48X8.

NOTE: After completing

system installation and

power-up, you must config-

ure the CM6800 and the

camera/receiver. Refer to

the System Start-Up section.

00628

Figure 7. PTZ Control Connections

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITORS

The CM6800 supports eight monitors.

1. Install monitors according to the instructions provided with them.

2. Connect the monitor cables at the appropriate video output BNC receptacles on the

back of the CM6800.

3. Terminate cables at the monitors. If you are looping to other devices, unterminate all

but the last device.

00629

Figure 8. Connecting Monitors

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARMS

The CM6800 provides numerous alarm handling options. Refer to the Programming section

for a detailed description.

1. Connect wires from the sensors to the respective alarm input points on the connectors

at the back of the CM6800. Each sensor requires two wires – one wire to the alarm

input terminal and a return wire to one of the ground terminals on the connector. The

CM6800 supports eight internal alarms.

Alarm sensors can be either N.O. (normally open) or N.C. (normally closed) contacts.

The CM6800 is set to N.O. as a factory default.

2. If your system requires more than eight alarms, connect an ALM2064 unit to the

system. Refer to the M Devices section.

00631

Figure 9. Connecting Alarms

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING DEVICES THROUGH THE COMMUNICATION PORTS

The CM6800 Matrix Switcher/Controller provides eight communication ports on the rear

panel for connecting peripheral components. You can connect a wide variety of devices,

such as keyboards, a personal computer (for either the CM6800 MGR package or ASCII

control), alarm and relay boxes, and multiplexers. Instructions are provided in this section

for the most commonly used connections.

NOTE: Connection instruc-

tions for other peripheral

devices, such as the

CM9760-MDA or

CM9760-CDU-T, are

provided as Pelco Technical

Tips, available from the

Pelco web site or from a

Technical Support represen-

tative (1-800-289-9100). For

more information, go to

www.pelco.com and select

Resources. Then select

Technical Tips.

The CM6800 communication ports are labeled COM 1 through 8. Port 1 is available either

as a DB9 connection, or as an RJ-45 connection. Ports 2 through 8 are RJ-45 connections.

In the programming menus these are referred to as serial ports 1 through 8.

COM PORTS 7, 8

RS-485 (PROGRAMMABLE

TO RS-232), RJ-45

PIN 1

PIN 8

RS-485 FUNCTION

1-----Rx+

RS-232 FUNCTION

1-----Rx

2-----Rx-

2-----NC

3-----NC

4-----NC

3-----NC

4-----NC

5-----GROUND

6-----NC

7-----Tx-

5-----GROUND

6-----NC

7-----NC

8-----Tx+

8-----Tx

COM PORT 1

RS-232,DB9

COM PORTS 1, 2

RS-232, RJ-45

COM PORT 3

M, RS-485, RJ-45

COM PORT 4

RS-485, RJ-45

COM PORTS 5, 6

RS-485, RJ-45

PIN 1

PIN 5

PIN 1

PIN 8

PIN 1

PIN 8

PIN 9

PIN 6

1-----NC

2-----Rx

3-----Tx

4-----NC

5-----GROUND

6-----NC

1-----Rx

1-----Rx+

2-----Rx-

3-----NC

4-----NC

5-----GROUND

6-----NC

1-----Rx+

2-----Rx-

3-----NC

1-----Rx+

2-----Rx-

3-----KBD 12V

4-----KBD GROUND

5-----GROUND

6-----NC

2-----NC

3-----NC

4-----NC

5-----GROUND

6-----NC

7-----NC

8-----Tx

4-----NC

5-----GROUND

6-----NC

7-----Tx-

7-----NC

8-----NC

7-----Tx-

8-----Tx+

7-----Tx-

8-----Tx+

9-----NC

NC = NO CONNECTION

Figure 10. Communication Port Connections and RJ-45 Connector Pin-Outs

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

The communication ports are wired for either RS-232 or RS-485 (the wiring can be selected

for COM 7 and 8). Refer to the following tables for the CM6800 default communication port

settings. Some ports can be programmed for other devices; this will be done when you

program the CM6800.

Table B. Communication Port Devices and Wiring

Port

Default Device

Wiring

Programmable to Other Device(s)

COM 1

PC Setup – CM6800MGR program

RS-232

ASCII device

(accessible with a DB9

connection or an RJ-45

connection)

COM 2

COM 3

ASCII device

RS-232

RS-485

M devices — ALM2064, REL2064,

KBD960

COM 4

COM 5

Genex multiplexer

RS-485

CM9760-MDA, ASCII

Keyboard (direct powered) –

KBD100, 200, & 300

RS-485 plus power

COM 6

COM 7

COM 8

Keyboard (direct powered) –

KBD100, 200, & 300

RS-485 plus power

RS-232 or RS-485

ASCII device

CM9760-MDA, keyboards

(KBD100, 200, & 300)

ASCII device

MDA, keyboards

(KBD100, 200, & 300)

Table C. Default Port Settings

NOTE: Refer to the

Programming section for

instructions on changing

Serial Port settings.

Port

Default Settings

COM 1

COM 2

COM 3

COM 4

COM 5, 6

COM 7, 8

MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit

ASCII, RS-232, 9600 baud, no parity, 8 data bits, 1 stop bit

M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit

MUX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

KBD-300, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

ASCII, RS-485, 9600 baud, no parity, 8 data bits, 1 stop bit

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

COM 1

PC SETUP (RS-232)

USE DB9 CONNECTION

OR ALTERNATE RJ-45 CONNECTION

BOTH CANNOT BE USED SIMULTANEOUSLY

PC DB9 CONNECTION

RS-232 NULL MODEM CABLE

NOTE: TOTAL NUMBER OF

KBD100/200/300 SERIES

KEYBOARDS CONNECTED

TO THE CM6800 CANNOT

EXCEED 16

COM 5 & 6

LOCAL KEYBOARDS (RS-485)

KBD100/200/300 SERIES

MAX # OF DEVICES = 8

ALARM

COM

PC RJ-45 CONNECTION

CONTROL

PTZ

OUT

COM 2

(RS232)

ASCII CONTROL ONLY

COM

ALTERNATE EQUIPMENT

120/230~

50/60 HZ

25 WATTS

VIDEO OUTPUTS

COM 7 & 8

(RS-485 OR RS-232)

COM 4

GENEX (RS-485)

ALSO PROGRAMMABLE FOR CM9760-MDA OR ASCII

MAX # OF DEVICES = 8

PROGRAMMABLE FOR KBD100/200/300 SERIES,

ASCII CONTROL, OR CM9760-MDA

COM 3

M DEVICES (RS-485)

MAX # OF DEVICES = 6

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16 pF PER FT (pF =PICO FARADS)

STRAIGHT

CABLES

12V 50 Hz

TRANSFORMER

ALM2064

NUMBER SUPPORTED = 2

64 ALARMS X 2 = 128 ALARMS

CM9505UPS

POWER SUPPLY

KBD960

REL2064

NUMBER SUPPORTED = 2

64 RELAYS X 2 = 128

KBD960

NUMBER SUPPORTED = 2

Figure 11. CM6800 Communication Port Connections and Options

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD100, KBD200, AND KBD300 SERIES KEYBOARDS

You can connect up to eight KBD100/200/300 Series keyboards to any of the following ports:

•

COM 5 (1 direct-powered keyboard or up to 8 remotely connected keyboards)

COM 6 (1 direct-powered keyboard or up to 8 remotely connected keyboards)

COM 7 (up to 8 remotely connected keyboards)

COM 8 (up to 8 remotely connected keyboards)

The total number of KBD100/200/300 Series keyboards connected to the CM6800 cannot

exceed 16.

KBD100, KBD200, and KBD300: Direct-Powered Keyboards

Use COM 5 and 6 (Serial Ports 5 and 6) for direct-powered local keyboards. Each port can

power one KBD100/200/300 Series keyboard.

If you are connecting more than one keyboard to COM 5 or 6, a KBDKIT(-X) is required for

each keyboard. Refer to the KBD100, KBD200, and KBD300: Remote Keyboards section.

1. Using the 25-foot (7.62 m) straight data cable supplied with the keyboard, plug one

end into the RJ-45 connector on the rear of the keyboard.

00603

Figure 12. Data Cable Plugged into Local Keyboard

2. Plug the other end of the data cable into either COM 5 or 6 on the CM6800.

NOTE: If distance between

CM6800 and keyboard

exceeds 25 feet, use

KBDKIT(-X).

00604

Figure 13. Data Cables Plugged into COM 5 and 6

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Set the keyboard DIP switches for the desired address for the local keyboard (refer to

Figure 12 and Table D).

Table D. Keyboard Addresses: KBD100/200/300 Series Keyboards

Keyboard

Address

Switch Settings

OFF

Table E. Switch Settings—KBD200/300 Keyboards Only

Keyboard

Switch

KBD200

KBD300

OFF

OFF (NOT USED)

OFF

ON or OFF*

* Switch 6 enables/disables turbo pan (can be switched while keyboard is on).

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD100, KBD200, and KBD300: Remote Keyboards

Use COM 5, 6, 7, or 8 for remote keyboard connections. Each port can support up to eight

KBD100/200/300 Series keyboards. Do not exceed a total capacity of 16 keyboards

connected to the CM6800.

NOTE: A KBDKIT or

KBDKIT-X is required to

connect remote keyboards.

The KBDKIT consists of two

RJ-45 wall blocks and one

120V, 60 Hz to 12V, 60Hz

transformer. The KBDKIT-X

has a 230V, 50 Hz to 12V,

50 Hz transformer. Use one

wall block for each key-

board.

If using COM 7 or 8, you will need to change the settings (the default setting is for an ASCII

device.) Refer to the Programming section for instructions.

1. Select a suitable location for each keyboard and wall block. Wall blocks must be within

6 feet (1.8 m) of a suitable electrical outlet. Do not mount the wall blocks yet.

2. Connect each keyboard to a wall block, using the keyboard data cable supplied with

the keyboard.

3. Remove the wall block covers and wire the connections between each wall block.

Connect to a final wall block (which will be connected to the CM6800).

Communication to the keyboards is RS-485. Pelco recommends using four-conductor,

shielded 18-gauge twisted pairs, such as Belden 9418 or similar cable, that meets or

exceeds the basic requirements for EIA RS-485 applications.

4. At each wall block, wire the KBDKIT(-X) transformer to pins 3 and 4. Polarity is

unimportant.

5. Replace the cover on the wall block. Secure the wall block to a suitable surface. A

double-sided sticky pad is provided to mount the wall block.

6. Set the address switches for each keyboard according to Table D.

NOTE: If you do not

connect keyboards to

7. Connect the final wall block to COM 5, 6, 7, or 8 on the CM6800, using a straight data

cable (supplied with the CM6800).

COM 7 or 8, either port can

be used for a CM9760-MDA

or an ASCII device.

Connection instructions for

CM9760-MDA are provided

as a Pelco Technical Tip.

Refer to the note on page

17. For ASCII devices, refer

to the documentation that

comes with the equipment.

00605

Figure 14. Remote Keyboards

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

M DEVICES

M protocol devices (KBD960/KBR960 keyboards, ALM2064 Alarm Interface Units, and

REL2064 Relay Interface Units) can be connected to COM 3 on the CM6800.

If only one device is to be connected to COM 3, use the instructions for that device in the

following sections.

If more than one device is to be connected to COM 3, refer to the Multiple M Devices

section.

Connect M devices to the CM6800 with straight cables. Four straight cables and one

reversed cable are supplied with the CM6800 (save the reversed cable for connecting a

Genex Multiplexer, if applicable).

M Devices Addressing

NOTE: If you wish to use

the partitioning and priority

features of the CM6800, you

must number KBD960/

KBR960 keyboards within a

range of 1-8.

Each M device connected to the CM6800 must have a unique local address within a range

of 1-16. Use the hardware DIP switches to set the appropriate ALM2064 and REL2064

local addresses. Specify the appropriate KBD960/KBR960 local address through the

keyboard Setup Mode after you complete the system installation (refer to the System Start-

Up section).

For use with the CM6800, Pelco recommends numbering M devices in a sequential order.

In a sample application, with two of each M device, you might assign local addresses as

follows:

M device local addresses:

Default

Recommended for CM6800

KBD960/KBR960:

REL2064:

ALM2064:

1, 2

3, 4

5, 6

TO IDENTIFY A CABLE

TYPE, PHYSICALLY

ORIENT THE RJ-45

CABLE AS DEPICTED

IN THE ILLUSTRATIONS.

ORIENT THE CONNECTORS

SIDE BY SIDE. TAB

SIDE DOWN. USE

COMPARED "COLOR RUN"

IS IN OPPOSITE DIRECTION

COMPARED "COLOR RUN"

IS IN SAME DIRECTION

BROWN BROWN

BROWN

REVERSED CABLE

STRAIGHT CABLE

THE COLOR RUN

OF THE WIRES TO

DETERMINE CABLE

TYPE.

00612

Figure 15. RJ-45 Cable Types

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Single KBD960/KBR960 Keyboard

To connect a single KBD960/KBR960 Keyboard to the CM6800:

1. Connect the keyboard to the CM9505UPS using the straight cable supplied with the

keyboard.

2. Connect the CM9505UPS to COM 3 on the CM6800 using the 6-foot (1.8 m) straight

data cable supplied with the CM6800.

NOTE: After completing

system installation and

power-up, you must config-

ure the KBD960/KBR960

settings. Refer to the System

Start-Up section.

00607

Figure 16. Connecting a KBD960/KBR960 to the CM6800

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Single ALM2064 Alarm Interface Unit

To connect a single ALM2064 Alarm Interface Unit:

1. Connect the ALM2064 OUT port to COM 3 on the CM6800 using the 6-foot (1.8 m)

straight data cable supplied with the CM6800.

2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default

address setting is 1). Refer to the ALM2064 Alarm Interface Unit Installation/Operation

Manual for instructions.

00608

Figure 17. Connecting a Single ALM2064 Alarm Interface Unit

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Single REL2064 Relay Interface Unit

To connect a single REL2064 Relay Interface Unit:

1. Connect the REL2064 OUT port to COM 3 on the CM6800 using the 6-foot (1.8 m)

straight data cable supplied with the CM6800.

2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default

address setting is 1). Refer to the REL2064 Relay Interface Unit Installation/Operation

Manual for instructions.

00609

Figure 18. Connecting a Single REL2064 Relay Interface Unit

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiple M Devices

Multiple M devices (KBD960/KBR960, ALM2064, and REL2064) can be connected to COM

3 on the CM6800, either as local devices or remote devices (when connecting two

KBD960/KBR960 keyboards to the CM6800, you must use a remote connection).

MULTIPLE M DEVICES: LOCAL CONNECTION

1. If you are connecting a KBD960/KBR960, connect it to the CM9505UPS with the

straight cable supplied with the keyboard. Then connect the CM9505UPS to the IN

port on the next unit (either the ALM2064 or the REL2064) with a 6-foot (1.8 m)

straight cable (supplied with the CM6800).

2. Connect each ALM2064 and REL2064 unit to the next unit with a 6-foot (1.8 m) straight

cable (supplied with the CM6800) from the OUT port to the IN port on the next unit. You

can connect a maximum of two ALM2064 units and two REL2064 units to the CM6800.

3. Connect the last unit to the CM6800 with a 6-foot (1.8 m) straight cable (supplied with

the CM6800) from the OUT port to COM 3 on the CM6800.

COM 3

DEFAULT SETTINGS: M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT

MAX # OF DEVICES = 6

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

ALARM

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16pF PER FT (pF = PICOFARADS)

COM

CM6800 COM 3

RJ-45 PIN-OUTS

CONTROL

PTZ

1 Rx+

2 Rx-

OUT

STRAIGHT CABLE

(SUPPLIED)

GND

COM 1

7 Tx-

8 Tx+

CM9505UPS

120/230~

50/60 HZ

25 WATTS

VIDEO OUTPUTS

STRAIGHT CABLE

(SUPPLIED)

STRAIGHT CABLE

(SUPPLIED)

RS-485

ALM2064

KBD960

RJ-45 PIN-OUTS

1 Tx+

KBD960

2 Tx-

RJ-45 PIN-OUTS

REL2064

1 Tx+

2 Tx-

REL2064

RJ-45 PIN-OUTS

7 Rx-

8 Rx+

1 Tx+

2 Tx-

7 Rx-

8 Rx+

7 Rx-

8 Rx+

Figure 19. Connecting Multiple M Devices – Local Connection

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MULTIPLE M DEVICES: REMOTE CONNECTION

Use a remote connection when the distance from the CM6800 is greater than 6-feet (1.8 m).

1. Connect each ALM2064 and REL2064 unit to a wall block with a 6-foot (1.8 m) straight

cable (supplied with the CM6800). You can connect a maximum of two ALM2064 units

and two REL2064 units to the CM6800.

2. If you are connecting a KBD960, connect it to the CM9505UPS with the straight cable

supplied with the keyboard. Then connect the CM9505UPS to a wall block with a

6-foot (1.8 m) straight cable (supplied with the CM6800). You can connect a maximum

of two KBD960 keyboards to the CM6800.

3. Connect the wall blocks to a final wall block. If additional wall blocks are needed, order

part number CON12J008Z03G0Z.

4. Connect the terminal wall block to COM 3 on the CM6800 using a 6-foot (1.8 m)

straight cable (supplied with the CM6800).

COM 3

DEFAULT SETTINGS:

M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT

MAX # OF DEVICES = 6

ALARM

COM

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16pF PER FT (pF = PICOFARDS)

CONTROL

PTZ

CM6800 COM 3

RJ-45 PIN-OUTS

OUT

1 Rx+

2 Rx-

COM 1

GND

120/230~

50/60 HZ

25 WATTS

VIDEO OUTPUTS

7 Tx-

8 Tx+

STRAIGHT CABLE

(SUPPLIED)

STRAIGHT CABLE

(SUPPLIED)

ALM2064

REL2064

KBD960

STRAIGHT CABLE

TO CM9505UPS

(SUPPLIED)

CONNECT THROUGH

THE “OUT” PORT

CONNECT THROUGH

THE “OUT” PORT

ALM2064

RJ-45 PIN-OUTS

REL2064

RJ-45 PIN-OUTS

KBD960

RJ-45 PIN-OUTS

1 Tx+

2 Tx-

1 Tx+

2 Tx-

1 Tx+

2 Tx-

7 Rx-

8 Rx+

7 Rx-

8 Rx+

7 Rx-

8 Rx+

Figure 20. Connecting Multiple M Devices – Remote Connection

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING A PC

The CM6800 provides PC-based setup and programming software that facilitates complete

switcher programming and configuration. Refer to the CM6800-MGR Quick Start Guide for

instructions on using the software.

Connect a PC to the CM6800 to access the CM6800-MGR software or to download

upgrades to the software. You can connect a PC to the CM6800 through either a DB9 port

or an RJ-45 port. You cannot use both ports simultaneously.

NOTE: You can also

connect an ASCII device

through COM 1, 2, 7, or 8.

Using an ASCII device

through COM 1 requires a

change in serial port

settings. Refer to the

Programming section for

instructions.

1. Using a null modem cable (user-supplied), plug one end into the DB9 COM 1 port on

the PC.

2. Plug the other end of the cable into the DB9 COM 1 port of the CM6800.

NULL MODEM CABLE

PIN 1

PIN 5

CM6800 COM 1

DB9 PIN-OUTS

PC COM 1

DB9 PIN-OUTS

PIN 2 = RX IN

PIN 3 = TX OUT

PIN 5 = GND

PIN 2 = RX IN

PIN 3 = TX OUT

PIN 5 = GND

00613

PIN 9

PIN 6

Figure 21. PC Connection to DB9 Port

1. Using a modified null modem cable (user-supplied), connect the DB9 COM 1 port on

the PC to an RJ-45 wall block (supplied with the CM6800 Matrix Switcher).

The modified null modem cable should be cut at one end, so that you can connect the

wires directly to the wall block pins.

2. Using a 6-foot (1.8 m) data cable (supplied with the CM6800 Matrix Switcher), connect

the wall block to the RJ-45 COM 1 port of the CM6800.

CM6800 COM 1

RJ-45 PIN-OUTS

PC COM 1

DB9 PIN-OUTS

PIN 1 = RX IN

PIN 5 = GND

PIN 8 = TX OUT

PIN 2 = RX IN

PIN 3 = TX OUT

PIN 5 = GND

CM6800 COM 1

PC COM 1

RJ-45 WALL BLOCK

AND STRAIGHT CABLE

SUPPLIED WITH CM6800

MODIFIED NULL MODEM CABLE

(USER-SUPPLIED)

00992

Figure 22. PC Connection to RJ-45 Port

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING GENEX MULTIPLEXERS

Use COM 4 to connect up to eight Genex Multiplexers to the CM6800.

NOTE: If you do not con-

nect multiplexers to COM 4,

you can connect a

CM9760-MDA or an ASCII

device through COM 4. Us-

ing either device requires a

change in serial port set-

tings. Refer to the Program-

ming section.

1. Connect the COM IN port of the multiplexer to COM 4 on the CM6800, using the

6-foot (1.8 m) reversed data cable supplied with the CM6800.

One reversed cable and four straight cables are supplied with the CM6800. Use the

reversed cable for connecting the Genex multiplexer to the CM6800.

A straight data cable is supplied with the Genex multiplexer. Use this cable for

connecting a second Genex multiplexer to the first multiplexer, if necessary.

2. Connect the MAIN monitor output from the multiplexer to any of the 48 camera inputs

on the CM6800.

3. Connect cameras to the multiplexer and then loop them to the CM6800. Refer to the

MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual

for detailed camera connection instructions. Terminate the video loop at the CM6800.

4. If required, you can connect a total of eight Genex multiplexers through COM 4. Daisy-

chain the multiplexers by connecting a straight data cable from the COM OUT port on

the first multiplexer to the COM IN port on the second multiplexer; connect the COM

OUT port on the second multiplexer to the COM IN port on the third multiplexer.

Continue to the eighth multiplexer, if necessary.

Refer to the System Start-Up section for additional configuration steps required when using

a Genex Multiplexer.

ALARM

COM

CONTROL

PTZ

OUT

COM

120/230~

50/60 HZ

25 WATTS

ALTERNATE SOURCE INPUTS

VIDEO OUTPUTS

REVERSED CABLE

SPOT MAIN

VCR

IN COM OUT

ALARMS

OCC S

OUT

AUX

MONITOR SIGNAL OUT

110-240V 50/60 Hz

10 111213141516

SVHS

GENEX MULTIPLEXER

STRAIGHT CABLE

SPOT MAIN

AUX

VCR

SVHS

VCR

IN COM OUT

ALARMS

OCC S

OUT

110-240V 50/60 Hz

10 111213141516

SVHS

GENEX MULTIPLEXER

RJ-45 PIN-OUTS

CM6800 COM 4

RJ-45 PIN-OUTS

GENEX MULTIPLEXER

STRAIGHT CABLE

Rx+ 1

Rx- 2

12VAC (OUT) 3

12VAC (OUT) 4

GROUND 5

NC 6

1 Rx+

2 Rx-

3 NC

4 NC

5 GROUND

6 NC

SPOT MAIN

IN COM OUT

ALARMS

OCC S

OUT

AUX

110-240V 50/60 Hz

10 111213141516

SVHS

Tx- 7

Tx+ 8

7 Tx-

8 Tx+

GENEX MULTIPLEXERS-8 MAXIMUM

00616

Figure 23. Connecting Genex Multiplexers

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

LOCAL AUXILIARIES

The CM6800 provides three local auxiliary (AUX) outputs on the rear panel for controlling

VCRs, printers, and other devices. These outputs can be activated directly from a keyboard

by using the F1, F2, and F3 function keys, or they can be activated by an alarm (deter-

mined by programming). Both relay contacts and TTL outputs are used.

In addition, you can connect up to two REL2064 Relay Interface Units to the CM6800. Note

that since operation of the three internal auxiliary relays on the CM6800 will also operate

the first three relays on the external unit, the maximum capacity of the system may be

limited to 128 auxiliaries (depending on how you number the external relays). Refer to the

Connecting a Single REL2064 Relay Interface Unit section for connection instructions.

CONNECTING RELAY CONTACTS – AUX 1 AND 2

AUX 1 and 2 are dry contact relay outputs. Refer to Figure 25 for wiring details. Terminal

connections are provided for both normally open (N.O.) and normally closed (N.C.) contacts.

Do not exceed the voltage and current ratings for the relay contacts.

You will need to provide an external power source to operate your device. In most cases

you will also need an external current limiting resistor. The formula for calculating the

resistor value is given in Figure 25.

00617

Figure 24. Wiring the AUX 1 and 2 (Relay) Outputs

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING THE OPEN COLLECTOR OUTPUT – F3 (TTL)

F3 is a TTL open collector output. This output provides a path to ground to control the low

voltage trigger input on many devices. It can control higher voltage control inputs via

isolation relays. Refer to Figure 26 for wiring details.

Do not exceed the voltage and current ratings for the TTL output.

An external pull-up resistor is usually necessary. The formula for calculating the resistor

value is given in Figure 26.

00618

Figure 25. Wiring the F3 (TTL) Output

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM START-UP

After completing the system installation, follow the procedure below to start proper system

operation. Skip any “system-specific” steps that do not apply to your system setup.

POWER-UP THE SYSTEM

Plug the CM6800 power cord into a 120/230V, 50/60 Hz power source. Plug in and turn on

all devices connected to the CM6800.

Once the system is powered-up you will see video from camera 1 and the following time/

date stamp on all system monitors:

00620

Figure 26. CM6800 Time/Date Stamp on Monitor

The time stamp will be advancing in one-second increments. Wait five seconds before

proceeding.

INITIALIZE KEYBOARDS

You must specify a monitor for each keyboard after your first power-up or any time power is

cycled to the keyboard or the CM6800.

Always allow five seconds to elapse before specifying a monitor.

1. Enter a number (1-8) corresponding to the monitor output that is feeding the monitor

you are viewing.

2. Press the MON key. The keyboard LED displays the number you entered. This also

confirms successful communication between the keyboard and the CM6800. If the

keyboard LED does not display the monitor number, repeat 1 and 2.

If you are unable to select the monitor, refer to the Troubleshooting section.

CONFIGURE THE SYSTEM

If necessary, configure the CM6800 and associated equipment to your specific application.

The CM6800 is shipped from the factory with default programming settings. If the defaults

are acceptable, the CM6800 can be operated without any user programming. However, you

may want to program the basic system settings, such as time and date, and camera titles.

In addition, some or all of the following configuration steps may be necessary, depending

on your system.

Configure the CM6800 through Programming mode. Refer to the Programming section for

detailed instructions.

TIME AND DATE

Access the Time & Date programming screen to set the time and date, and select the time/

date format option.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA TITLES

By default each camera is titled “CAM #” (# = camera number from 1-48). Access the

Camera programming screen to change the camera titles.

VIDEO SOURCES

Extended Coaxitron protocol receivers can be operated without any programming changes.

For other receiver control protocols, access the Camera programming screen to select the

control type for the device connected to each video input. Control can be through standard

mode Coaxitron, extended mode Coaxitron, RS-422 PTZ through Port A or Port B on the

rear panel, or through a Genex Multiplexer.

For RS-422 PTZ control you must configure the CM6800:

•

Access the Camera programming screen to identify the receiver control type

(PTZ-A or PTZ-B) and to select the appropriate camera port address. The

camera port address must match the address setting configured through the

camera/receiver DIP switch settings.

Access the Port programming screen to select the appropriate communication

type (P or D) for serial ports 9 (PTZ-A) and 10 (PTZ-B). Default settings for PTZ-

A and PTZ-B: PTZ-P, RS-422, 4800 baud, no parity, 8 data bits, 1 stop bit.

You must also configure the camera/receiver. Refer to the appropriate camera/receiver

installation manual for configuration and address settings.

ALARMS

The CM6800 is shipped from the factory with the alarm contact enable field set to OFF. To

use the alarm features, access the Alarm programming screens to enable the alarm

contact.

COMMUNICATION PORTS

If you are using any communication port for a device not specified by the default setting,

you must access the Port programming screen to change the settings.

Table F. Default Port Settings

Port

Default Settings

COM 1

MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit

ASCII, RS-232, 9600 baud, no parity, 8 data bits, 1 stop bit

M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit

MUX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

KBD-300, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

ASCII, RS-485, 9600 baud, no parity, 8 data bits, 1 stop bit

PTZ-P, RS-422, 48 baud, no parity, 8 data bits, 1 stop bit

COM 2

COM 3

COM 4

COM 5, 6

COM 7, 8

PTZ-A (Port 9)

PTZ-B (Port 10)

KBD960/KBR960 KEYBOARD

Configure the KBD960/KBR960 settings.

1. Set DIP switch 2 to the ON position.

2. Enter Setup Mode. Set the local address (1-8). (Note: the baud rate is set by default to

19200.) Each M device connected to the CM6800 must have a unique local address.

Refer to the KBD960/KBR960 Keyboard Installation/Operation Manual for detailed

setup instructions.

3. Return DIP switch 2 to the OFF position.

4. Press the EXIT icon on the keyboard LCD screen.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

GENEX MULTIPLEXER

Access the Camera programming screen and specify MUX control for all cameras

connected to the CM6800 through the Genex Multiplexer.

Access the CM6800 Camera programming screen to configure the following camera control

options for each camera connected to the CM6800 through the Genex Multiplexer:

•

CONTROL: MUX

PORT ADDRESS: assign the appropriate address. The port address must match

the “Unit ID” assigned through the Genex programming screens.

You must also configure the Genex Multiplexer. Refer to the MX4000 Genex Series

Simplex and Duplex Multiplexers Installation/Operation Manual (C1920M-B) for instructions

on accessing the Advanced System Setup programming screen. Select the following

options:

•

SPOT MONITOR DISPLAY: TRACK MAIN

UNIT ID (must match the port address assigned through the CM6800)

COMM. TYPE: SLAVE (each multiplexer connected to the CM6800 must be in

slave mode)

MONITOR COLOR ADJUSTMENT:

Once you have connected all devices and powered the system, use the CM6800 color bars

as a reference tool for adjusting the color on each monitor.

1. Enter 9999.

2. Press the CAM key. Broadcast quality color bars appear on the monitor.

3. Adjust color on each monitor as necessary until the color bars match the following

color order on the monitor (for black and white monitors you can use the color bars to

adjust brightness):

00630

Figure 27. CM6800 Color Bars

PROGRAM PRESETS

Program presets as necessary for your system. Refer to the appropriate keyboard manual

for instructions.

ADDITIONAL PROGRAMMING

Refer to the Programming section for complete instructions on programming the CM6800.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING THE CM6800

The CM6800 is shipped from the factory with default programming settings. If the defaults

are acceptable, the CM6800 can be operated without any user programming. However, you

may want to program the following basic system settings:

•

Time and date

Camera titles

PTZ control via hardwire data connections

Alarm contacts

Alarms must be enabled before they are functional.

•

Access/Partitioning

All access is set to YES by factory default.

Communication ports

If you connect your system as illustrated in the Quick Start Guide, you must

change the settings for Port 7 or 8 in order to connect remote keyboards.

You can further customize your system with a wide range of programming options, such as:

•

select the language displayed on programming screens

establish monitor group sequences

set monitor display options

set alarm handling options

assign logical camera numbering

change password

set auxiliary options

CUSTOMIZING THE CM6800

NOTE: The CM6800 allows

system programming from

only one monitor at a time. If

programming from the

CM6800-MGR is sent to the

CM6800 at the same time

that you are programming

from a monitor screen, the

system will exit the on-screen

programming function.

Pelco provides two options for programming the CM6800 to your specifications:

•

Password-protected, on-screen programming screens accessible directly from

the Matrix Switcher

PC-based CM6800-MGR software

Refer to the CM6800-MGR Quick Start Guide for instructions on accessing and

using this software to program your system.

NOTE: Pelco strongly recommends uploading your programming settings

to the CM6800-MGR to save settings in the event of an accidental reset.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESS PROGRAMMING MODE FROM THE CM6800

KBD100/200/300 Keyboards

KBD960/KBR960 Keyboards

1. Press the PGM key.

NOTE: If you have not

already done so, enter the

monitor number and press

the MON key to select the

monitor. On the KBD960/

KBR960, the Camera menu

appears on the LCD display.

1. Select

2. Select

DEF

3. Enter the Define PIN (Default: 1234).

4. Select

5. Select

PGM

The Password screen appears on the monitor.

Press

to exit the

Camera menu.

PELCO VIDEO SWITCHER

MODEL CM6800

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

MACRO STATUS VIEW

RETURN

Figure 28. CM6800 Password Screen

At the ******* prompt, enter the DEFAULT PASSWORD: 2899100

The Main Menu appears.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

Figure 29. CM6800 Programming Main Menu

If necessary, select the appropriate language.

1. Navigate to the language displayed below the menu options.

2. Scroll through the languages and select the language appropriate for your system.

OPTIONS:

ENGLISH

ESPANOL

DEUTSCH

FRANCAIS

PORTUGUESE

ITALIANO

3. Navigate to the RETURN field and navigate left or right to return to the Main Menu.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Exit Programming Mode

KBD100/200/300 Keyboards

KBD960/KBR960 Keyboards

To return to active video you can:

•

Press the PGM key once while

in the Main Menu.

PGM

•

Select

Menu.

once while in the Main

•

Press the PGM key twice from

anywhere else in the program-

ming screens.

PGM

Select

twice from anywhere else in

the programming screens.

Navigate to the RETURN field and

navigate left or right to return to the

previous screen or menu.

•

Navigate to the RETURN field

and navigate left or right to

return to the previous screen or

menu.

NAVIGATE AND SELECT OPTIONS/FIELD ENTRIES IN

PROGRAMMING MODE

During programming, a menu appears on the monitor screen. The currently selected field blinks.

Use the following keys or joystick on your keyboard to navigate the programming screens.

Function

Keyboard

Navigate programming screens.

KBD100

Use the sequence and macro keys.

Left

Right

Down

MAC

HOLD

KBD200

Use the Pan/Tilt positioning keys.

Left

Right

Down

KBD300

Use the joystick.

TIP: To access a screen

or enter a value, press a

number key on the keyboard

and then press F1

Left

Right

Down

KBD960/KBR960

(KBD100/200/300) or select

(KBD960/KBR960).

Use the joystick. (See above icons)

Select the appropriate icon on the

KBD960/KBR960 LCD SCREEN.

Left

Right

Down

Access a screen from the Main

Menu (or from a submenu).

All Keyboards

1. Navigate down to the desired menu

option.

2. Navigate left or right to select the menu

option.

1. Using the numerical keypad, enter the

number of the menu option.

2. Press F1 on the KBD100/200/300

keyboard or select

KBR960 keyboard.

on the KBD960/

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Function

Keyboard

Scroll through options in

programming fields.

KBD100/200/300

Use F1 and F2. Or (KBD300 only) use the

joystick to navigate left or right.

NOTE: The joystick does not scroll options

in all fields.

KBD960/KBR960

Select the

icons or use the

joystick to navigate left or right.

NOTE: The joystick does not scroll options

in all fields.

All keyboards

Select option in a programming field.

1. Scroll through the options until the

appropriate entry appears in the field.

2. Navigate to the next field or press PGM

to exit.

NOTE: On the Monitor and Time & Date

screens you must apply the changes (refer

to Time & Date or Monitor in this section).

Enter a numerical value in an option

field (not available in all fields).

All keyboards

1. Using the numerical keypad, enter a

number within the range of valid options

(example: to enter an internal alarm

contact you must enter a number

between 1 and 8).

2. Press F1 on the KBD100/200/300

keyboard or select

KBR960 keyboard.

on the KBD960/

Access the HELP screen

(Sequences, Macros, and Alarm

Group screens).

All keyboards

1. Navigate to the HELP field.

2. Press F1.

All keyboards

Access the NEXT or PREVIOUS

page of a list (not available on every

screen).

1. Navigate to the NEXT or PREVIOUS

field.

2. Press F1.

Exit a screen.

All keyboards

1. Navigate to the RETURN field.

2. Navigate left or right.

Press the PGM key to return to the previous

screen or menu.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ABOUT CM6800

The About CM6800 screen displays system version levels.

PELCO SWITCHER

MODEL CM6800

ABOUT CM6800

MAIN MENU

CODE:

VERSION

VER MON

VER CXT

CER CPU

VER VID

V1.03

V1.02

V1.02A

V1.02

MONITOR FPGA:

COAX FPGA:

CPU FPGA:

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

VIDEO FPGA:

FONTS

VER FNT

V1.02

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

ITALIAN:

PORTUGUESE:

FRENCH:

GERMAN:

SPANISH:

ENGLISH:

VER ITA

V1.02

VER POR

VER FRE

VER GER

VER SPA

VER ENG

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

BOOTROM

EID#:

VER V1.01

113-145119079400000

ENGLISH

RETURN

00654

Figure 30. Access the About CM6800 Screen

ACCESS (SYSTEM PARTITIONING)

The CM6800 supports the following system partitioning to control switching system access:

NOTE: To use partitioning

for keyboards, all keyboard

addresses must be within a

range from 1-8.

Keyboard to Monitor:

Camera to Keyboard:

Restrict a keyboard from accessing selected monitors.

Restrict a keyboard from calling selected cameras to monitors. Or

video viewing only: permit the viewing of selected cameras while

preventing pan and tilt control.

Camera to Monitor:

Restrict the viewing of selected cameras on selected monitors.

All system access is set to YES by default.

Keyboard to Monitor Access

Use the Keyboard to Monitor Access screen to assign keyboards control of specific

monitors.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

KEYBOARD TO MONITOR ACCESS

ACCESS

PORT 7

KEYBOARD TO MONITOR

CAMERA TO KEYBOARD

CAMERA TO MONITOR 1-8

CAMERA

MON

KEYBOARD

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00636

00654

00651

Figure 31. Access the Keyboard to Monitor Access Screen

NOTE: If you connect an

ASCII keyboard/device to

the CM6800 (COM port 1, 2,

4, 7, or 8), you can connect

only one keyboard to a port.

Specify access in the first

column only (address 1).

PORT:

Select the COM port number for which you are programming access

control (1-8).

In each monitor row specify the access allowed for each keyboard (address 1-8) to control

each specific monitor (1-8).

OPTIONS:

Y = Yes; control is allowed

N = No; control is not allowed

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Camera To Keyboard Access

Use the Camera to Keyboard Access screen to assign keyboards full control or view-only

control of specific cameras.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA TO KEYBOARD ACCESS

ACCESS

PORT 5

KEYBOARD

KEYBOARD TO MONITOR

CAMERA TO KEYBOARD

CAMERA TO MONITOR 1-8

CAM

0001

0002

0003

0004

0005

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00636

00654

00644

Figure 32. Access the Camera to Keyboard Access Screen

PORT:

Select the COM port number for which you are programming access

control (1-8); keyboards are identified by their physical connection to

the switcher.

In each camera row specify the access allowed for each keyboard (address 1-8) to view

and control the specific logical camera number; select NEXT or PREVIOUS to continue to

the next group of camera numbers.

OPTIONS:

Y = Yes; viewing and control is allowed

N = No; viewing and control is not allowed

V = View only; camera can be viewed but not controlled

Camera To Monitor Access

Use the Camera to Monitor Access screen to assign monitors viewing access to specific

cameras.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA TO MONITOR ACCESS

ACCESS

MONITOR

CAM

0001

0002

0003

0004

0005

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

KEYBOARD TO MONITOR

CAMERA TO KEYBOARD

CAMERA TO MONITOR 1-8

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00636

00654

00645

Figure 33. Access the Camera to Monitor Access Screen

In each camera row specify the access allowed for each monitor (1-8) to display the

specific logical camera number; select NEXT or PREVIOUS to continue to the next group of

camera numbers.

OPTIONS:

Y = Yes; camera can be viewed

N = No; camera cannot be viewed

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARM CONTACTS

The CM6800 provides a wide variety of alarm handling and display options. Alarmed

cameras can be displayed on one or several monitors as part of one or several alarm

groups (each monitor can display only one alarm group.) You can also customize the

system to handle alarms in the following ways:

NOTE: You cannot access

the Alarm Contacts screen

when an alarm is active.

The message MONITOR:

00# IS IN ALARM. ACCESS

IS DENIED appears (the

appropriate monitor number

appears in place of “00#”).

•

the order in which alarms are displayed

automatic or manual acknowledgement of alarms

activation of auxiliaries by alarms

automatic activation of presets or patterns

N.O. or N.C. operation

priority assignment

Before programming alarm settings, verify that no automated system functions are set to

run, such as a macro that would arm or disarm an alarm. Ensure that system operators do

not arm or disarm any alarms while you are programming the alarm settings. If an alarm is

triggered while you are in the CM6800 programming screens, or while programming a

pattern, preset or zone, the system will exit the on-screen programming function and

display the alarm on the appropriate monitor(s).

When programming an alarm to appear on a specific monitor, verify that the monitor has

access to the camera view triggered by the alarm. Partitioning has priority over alarm

programming, so if an alarm is cued to a monitor that does not have access to the

appropriate cameras, the camera views cannot be monitored.

Alarm Contact Programming Tasks

To configure the CM6800 internal alarm contacts you must access the Alarm Contact

screen to complete the following minimum tasks:

•

Enable the alarm contact.

Specify at least one camera step with a dwell greater than zero for each alarm contact.

Assign the alarm to at least one alarm group.

The following alarm handling options are set by factory default:

•

Acknowledgement type = manual

Time out = 10 seconds

Alarm sensor type = N.O. (normally open)

Priority level = 0

Alarm group display option = Block Build

To change these defaults, or to configure external alarm contacts, refer to the following

sections for detailed programming instructions.

Alarm Group Display Options

To display on a monitor, an alarm must be assigned to an alarm group (A-H). Before

programming alarms you may want to determine the alarm display format for each

alarm group. An alarm can include up to eight steps, so eight camera views could

display as a part of each alarm.

A priority alarm appears on system monitors before non-priority alarms, despite the order

specified by the alarm group assignment. In the examples below, all alarms are at the same

priority level. Refer to the PRIORITY description in Program Internal and External Alarms.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

BLOCK BUILD

Alarmed cameras are displayed across a block of alarm monitors in a sequential order. All

steps programmed for the alarm contact appear on the designated monitor.

Example: Eight alarms set to display on monitors 02-07 will appear in the following order:

ALARM MONITOR GROUP SETUP

1st Display

Cycle

Next Display

Cycle

Acknowledging

Alarms 1 & 2

Next Display

Cycle

MON

Monitor

—

02 B

1st alarm

1st and 7th

alarms cycle

Acknowledge

1st alarm

7th alarm

03 B

2nd alarm

2nd and 8th

alarms cycle

Acknowledge

2nd alarm

8th alarm

HELP

04 B

05 B

06 B

07 B

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

00638

New alarms display on the lowest monitor number with the fewest alarms cycling.

CHRONOLOGICAL PAIR: D AND Q

The oldest alarm of a specific group is displayed on one designated monitor, while all other

alarms in the group are sequenced on the second designated monitor. All steps pro-

grammed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 04 and 05 will appear in the following order:

ALARM MONITOR GROUP SETUP

Monitor

04 D

1 Alarm

2 Alarms

1st alarm

2nd alarm

3 Alarms

4 Alarms

MON

1st alarm

—

05 Q

2nd and 3rd

alarms cycle

2nd, 3rd, and 4th

alarms cycle

—

You must acknowledge alarms in a chronological pair from the display monitor (D). Then

the next oldest alarm moves to the display monitor and the remaining alarms continue to

cycle through the queue monitor (Q). This format requires you to acknowledge each alarm

in the order in which they occur.

HELP

00640

Acknowledging alarms in this example:

Monitor

1st Cycle

Next Cycle

04 D

Acknowledge

1st alarm

Acknowledge

2nd alarm

Acknowledge

3rd alarm

Acknowledge

4th alarm

05 Q

2nd, 3rd, and 4th

alarms cycle

3rd and 4th

alarms cycle

4th alarm

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

REVERSE CHRONOLOGICAL PAIR: M AND L

The most recent alarm of a specific group is displayed on one designated monitor, while all

other alarms in the group are sequenced on the second designated monitor. All steps

programmed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 06 and 07 will appear in the following order:

ALARM MONITOR GROUP SETUP

Monitor

06 M

1 Alarm

2 Alarms

2nd alarm

1st alarm

3 Alarms

4 Alarms

MON

1st alarm

3rd alarm

4th alarm

—

07 L

1st and 2nd

alarms cycle

1st, 2nd, and 3rd

alarms cycle

—

HELP

You must acknowledge alarms in a reverse chronological pair from the display monitor (M).

Then the next most recent alarm moves to the display monitor and the remaining alarms

continue to cycle through the queue monitor (L). This format requires you to acknowledge

each alarm in the reverse order from which they occurred.

00641

Acknowledging alarms in this example:

Monitor

1st Cycle

Next Cycle

06 M

Acknowledge

Alarm 4

Acknowledge

Alarm 3

Acknowledge

Alarm 2

Acknowledge

Alarm 1

07 L

Alarms 1, 2,

and 3 cycle

Alarms 1

and 2 cycle

Alarm 1

SALVO SWITCHING

Multiple camera views within the alarm contact programming (the “steps”) are displayed

simultaneously as a group across a set of monitors. When a new alarm triggers, all

monitors switch to the new alarm at the same time.

When programming a Salvo Group:

•

Program the Salvo Group to display across a number of monitors equal to the

number of steps in the alarm contact(s); for example if the alarm contact has six

steps, set the Salvo Group to display on six monitors. If an alarm contact

contains more steps than monitors defined for the Salvo Group, the additional

steps do not appear on a monitor during the alarm.

•

Each alarm contact assigned to the Salvo Group should contain the same

number of steps.

The Salvo Group switches based on the dwell time entered for the first step in

the alarm contact.

ALARM MONITOR GROUP SETUP

Example: Two alarm contacts with three steps display on three monitors will appear as follows:

MON

—

After

Acknowledging

1st Alarm

Next Display

Cycle

Monitor 1 Alarm

2 Alarms

06 S

07 S

08 S

1st alarm, step 1 2nd alarm, step 1

1st alarm, step 2 2nd alarm, step 2

1st alarm, step 3 2nd alarm, step 3

1st alarm, step 1

1st alarm, step 2

1st alarm, step 3

2nd alarm, step 1

2nd alarm, step 2

2nd alarm, step 3

HELP

00639

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Internal and External Alarms

Use the Internal Alarm screen to configure the eight internal alarm inputs on the rear panel

of the matrix switcher/controller; internal inputs are programmable to associate any camera

to any input. When an internal alarm is triggered, the alarm icon and an “I” appear on

designated system monitors.

Use the External Alarm screen to configure the alarm inputs on external devices; up to 128

additional inputs are available by connecting up to two ALM2064 Alarm Interface Units. When

an external alarm is triggered, the alarm icon and an “E” appear on designated system

monitors.

The procedure for programming internal and external alarms is the same, except for selecting

the alarm input type (the TYPE field on the Internal Alarm screen). Set the external alarm

input type (N.O. or N.C.) through the ALM2064 Alarm Interface Unit. Refer to the ALM2064

Alarm Interface Unit Installation/Operation Manual for instructions.

INTERNAL ALARM MENU

CONTACT:

ACK TYPE: MANUAL

TYPE:

ENABLE:

TIME OUT: 10

PRIORITY:

OFF

DWL CMD

01 PRES

STP CAM

## AUX

0001

— — — —000

— — — —00

PELCO SWITCHER

MODEL CM6800

MAIN MENU

ALARM CONTACTS

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

CAMERA

GROUP ENABLE

LOGICAL CAMERA

MONITOR

ACCESS

ALARM GROUP

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

00650

10 ALARM CONTACTS

11 EVENT TIMER

EXTERNAL ALARM MENU

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

CONTACT: 001

ACK TYPE: MANUAL

ENABLE:

TIME OUT: 10

OFF

PRIORITY:

ENGLISH

RETURN

STP CAM

DWL CMD

AUX

0001

— — — —00

— — — —000

— — — —00

00654

00642

GROUP ENABLE

RETURN

00649

Figure 34. Access the Internal or External Alarm Screen

CONTACT:

Select the alarm input number for programming.

OPTIONS:

Internal alarms: 1-8

External alarms: 1-128

ENABLE:

Enable the alarm contact by selecting ON (Default = OFF); to complete

the process of enabling an alarm contact, you must also

•

set at least one camera with a dwell time greater than 0 (refer to the

STP description),

assign the alarm contact to an alarm group (refer to the GROUP

ENABLE description).

ACK TYPE:

Select the alarm clearance type.

OPTIONS:

MANUAL = alarm must be acknowledged from a system keyboard

AUTO =

alarm will time out automatically after the interval specified

in the TIME OUT field

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

TIME OUT:

TYPE:

Enter the amount of time (0-99 seconds) alarm remains active after the

contact has cleared (AUTO alarms only).

Select the alarm input type (Internal Alarms only).

OPTIONS:

N.O. = normally open

N.C. = normally closed

PRIORITY:

Select the priority level of the alarm; a priority alarm appears on

system monitors before a non-priority alarm.

OPTIONS:

0 = non-priority

1 = priority

STP:

Each alarm contact can include up to eight steps to be activated as a

result of this alarm. For each step select entries in the following fields as

necessary.

CAM:

DWL:

Enter the logical number of the camera to be

displayed; must be a valid logical number (0001-9998).

Enter the amount of time the camera view is

displayed in an alarm sequence (0-99 seconds); to

enable the alarm contact you must set at least one

camera with a dwell time greater than 0.

CMD and ##:

Select a camera operation; if you select a pattern or

a preset, enter a valid pattern or preset number.

OPTIONS:

PRES = preset

PATT = pattern

RSCN = random scan

FSCN = frame scan

SSCN = stop scan

AUX and ##:

Select an auxiliary to be activated.

Global = internal and external auxiliaries.

NOTE: The auxiliaries on

the rear panel of the

CM6800 are activated by

global auxiliary numbers 1,

2, and 3

OPTIONS:

GON = turn global auxiliary on (1-128)

GOFF = turn global auxiliary off (1-128)

CON = turn camera auxiliary on (1-8)

COFF = turn camera auxiliary off (1-8)

GROUP ENABLE: Assign the alarm contact to one or more alarm groups (A through H).

OPTIONS:

Y = include in group

N = do not include in group

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Video Loss Alarm

You can program the CM6800 to detect video loss from any camera input and indicate the

loss through alarm mode – the alarm icon and a “V” (for video loss) appear on system

monitors as specified by alarm group assignment.

Use the Video Loss screen to configure the system to display an alarm based on video loss.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

ALARM CONTACTS

VIDEO LOSS MENU

PHYSICAL INPUT:

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

CAMERA

ENABLE: OFF

LOGICAL CAMERA

MONITOR

ACCESS

ACK TYPE: MANUAL

CAMERA 0001

TIME OUT: 10

ALARM GROUP

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

GROUP ENABLE

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00654

00642

00663

Figure 35. Access the Video Loss Screen

PHYSICAL INPUT: Select the physical input number; the logical camera number associ-

ated with the specific physical input appears on the screen below.

ENABLE:

Enable video loss detection for the specific video input by selecting ON

(Default = OFF); to complete the enable process, you must also assign

the alarm contact to an alarm group (refer to the GROUP ENABLE

description).

ACK TYPE:

Select the video loss alarm clearance type.

OPTIONS:

MANUAL = alarm must be acknowledged from a system keyboard

AUTO =

alarm will time out automatically after the interval specified

in the TIME OUT field

TIME OUT:

Enter the amount of time (0-99 seconds) alarm remains active after the

video has been restored (AUTO alarms only).

CAMERA 0001:

The logical camera number associated with the physical input specified

in the PHYSICAL INPUT field appears here.

GROUP ENABLE: Assign the video loss alarm to one or more alarm groups (A through H).

OPTIONS:

Y = include in group

N = do not include in group

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarm Groups

Use the Alarm Group screen to configure alarm groups to appear on system monitors. To

display on a monitor, an alarm must be assigned to an alarm group.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

ALARM CONTACTS

ALARM MONITOR GROUP SETUP

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

MON

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

—

ALARM GROUP

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

—

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

HELP

RETURN

ENGLISH

RETURN

00654

00642

00637

Figure 36. Access the Alarm Group Screen

Specify the display option for up to eight alarm groups (A through H). Refer to the Alarm

Group Display Options in this section. If you make an error in assigning alarm groups, the

message “ERROR IN GROUP” appears.

Display Option Display Option

Number of Monitors Displaying

Each Alarm Group

Entry

Type

block build

chronological pair

up to eight

D and Q

M and L

one display monitor (D), one queue monitor (Q)

reverse chronological pair one display monitor (M), one queue monitor (L)

salvo switching from two to eight

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUXILIARY OUTPUTS

The three local auxiliary (AUX) outputs on the rear panel of the CM6800 can be operated

manually from a system keyboard or automatically in response to an alarm.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

SET AUXILIARY MENU

AUX

MODE

ALM

MON

DWL

CAMERA

LAT

LOGICAL CAMERA

MONITOR

ACCESS

MOM

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00643

Figure 37. Access the Set Auxiliary Screen

MODE:

For each auxiliary select the operation mode.

OPTIONS:

ALM = activate the auxiliary as a response to an alarm; if you select

this mode, specify the monitor number and dwell time

LAT = latching operation

MOM = momentary operation

Specify values for the MON and DWL fields only when you select ALM in the MODE field.

MON:

DWL:

Specify the number of the monitor the auxiliary will follow (01-08).

Specify the amount of time the auxiliary will remain active after there is

no longer an alarm displayed on a monitor (01-99 seconds). The alarm

is displayed on a monitor until

•

the alarm is acknowledged manually (if MANUAL is selected in

the alarm contact ACK TYPE field),

the alarm contact times out (if AUTO is selected in the alarm

contact ACK TYPE field).

Refer to the ACK TYPE description in Internal and External Alarms and

in Video Loss Alarm.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA

Use the Camera screen to configure settings for each camera connected to the CM6800.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA 0001

VERTICAL DRIVE:

OFF

CONTROL:

PORT ADDRESS:

EXT COAX

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

CAMERA TITLE:

CAM 1

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00646

Figure 38. Access the Camera Screen

CAMERA:

Select the logical number of the camera (video input) to be defined

(0001-9998).

NOTE: To select logical numbers other than the default numbers

(001 to 0048) you must first program the logical numbering in the Logical

Camera screen. Refer to Logical Camera Numbers in this section.

VERTICAL DRIVE: Enable Vertical Drive (ON) to synchronize Pelco cameras that have the

ability to accept a synchronization pulse via the coax cable.

NOTE: The following Pelco

cameras are compatible

with the vertical drive option:

CONTROL:

Select the receiver control type for the device connected to this input;

that is, the type of receiver communication you will use to control a

camera’s pan and tilt and lens (if applicable).

CC3500H-2

CC3500S-2

CC3600H-2

CC3551H-2

MC3600H-2

MC3651H-2

MC3500S-2

OPTIONS:

EXT COAX: Coaxitron extended mode (32-bit)

STD COAX: Coaxitron standard mode (15-bit)

MUX: Genex multiplexer

PTZ-A: RS-422 Control Port A

PTZ-B: RS-422 Control Port B

NOTE: If you select PTZ-A or PTZ-B you must also specify the port

address (in the following field) and program Serial Port 9 or 10 (refer to

Ports in this section).

PORT ADDRESS: Required only for Genex multiplexer or RS-422 control.

Genex multiplexer: Select the address of the multiplexer (01-32); this

address must match the unit ID specified through multiplexer program-

ming. Refer to the MX4000 Genex Series Simplex and Duplex

Multiplexers Installation/Operation Manual.

RS-422 cameras connected through PTZ-A or PTZ-B: Select the

camera/device address for RS-422 control (01-32). The port address

must match the address setting configured through the camera/

receiver DIP switch settings.

CAMERA TITLE:

The camera title (up to 20 alphanumeric characters) appears on the

monitor during real-time camera display (refer to Monitor Display in this

section). Use F1 and F2 to scroll through the characters; once you

reach the desired character for a position, navigate to the next position.

The default characters are 26 upper case letters and the numbers 0-9.

You can add special characters, such as letters with accent marks

used in other languages, through the CM6800-MGR (refer to the

CM6800-MGR Quick Start Guide).

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

EVENT TIMERS

You can automate system operation to activate sequences or macros on specific monitors.

Events can be scheduled on a daily or weekly basis, or on a specific date such as a

holiday. If you set more than one timer to start at the same time, the timers will run in the

following order of precedence: weekly, special, daily.

On each event timer screen:

•

Two methods are provided for selecting the event time: scrolling through time values

or entering a valid hour and minute.

Each timer can activate either a macro or a sequence. Select a value for either the

MACRO field or the SEQ field.

A macro started by an event timer runs until the last step is completed (unless you

specify a loop in the macro).

A sequence started by an event timer runs continuously until another sequence or

macro begins, or until a system operator selects a different camera.

Daily Timer

Use the Daily Timer screen to schedule up to 32 daily events.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

DAILY TIMER 01

EVENT TIMER

ENABLE:

TIME:

OFF

12:02

DAILY TIMER

WEEKLY TIMER

SPECIAL TIMER

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

MACRO 00

MON SEQ

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00648

00647

Figure 39. Access the Daily Timer Screen

DAILY TIMER:

ENABLE:

TIME:

Select the timer number (01-32).

Enable (ON) or disable (OFF) the timer.

Set the hour and minute at which the event is to begin (24-hour time).

To activate a macro, select a valid macro number (01-32).

MACRO:

SEQ:

To activate a sequence, select a valid sequence number (01-16) to run

on a specific monitor.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Weekly Timer

Use the Weekly Timer screen to schedule up to 32 weekly events.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

EVENT TIMER

WEEKLY TIMER 01

ENABLE: OFF

DAILY TIMER

WEEKLY TIMER

SPECIAL TIMER

TIME:

SUN MON TUE WED THU FRI

MAC MAC MAC MAC MAC MAC MAC

24 01 01 01 01 01 24

MON SEQ SEQ SEQ SEQ SEQ SEQ SEQ

09:02

CAMERA

SAT

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00648

00664

Figure 40. Access the Weekly Timer Screen

WEEKLY TIMER: Select the timer number (01-32).

ENABLE:

TIME:

Enable (ON) or disable (OFF) the timer.

Set the hour and minute at which the event is to begin (24-hour time).

MACRO:

To activate a macro, in the column under the desired day of the week,

select a valid macro number (01-32).

SEQ:

To activate a sequence, in the column under the desired day of the

week, select a valid sequence number (01-16) to run on a specific

monitor.

Special Timer

Use the Special Timer screen to schedule up to 32 events on a specific date(s).

PELCO SWITCHER

MODEL CM6800

MAIN MENU

EVENT TIMER

SPECIAL TIMER 32

ENABLE: OFF

TIME: 10:00 DATE: 25-DEC-01

MACRO 00

DAILY TIMER

WEEKLY TIMER

SPECIAL TIMER

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

MON SEQ

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00648

00661

Figure 41. Access the Special Timer Screen

SPECIAL TIMER: Select the timer number (01-32).

ENABLE:

TIME:

Enable (ON) or disable (OFF) the timer.

Set the hour and minute at which the event is to begin (24-hour time).

Select the date on which the event is to begin (DD-MMM-YY).

To activate a macro, select a valid macro number (01-32).

DATE:

MACRO:

SEQ:

To activate a sequence, select a valid sequence number (01-16) to run

on a specific monitor.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

LOGICAL CAMERA NUMBERS

A logical number is a user-selectable, variable number, and is always associated with an

actual physical input. A physical input number represents an actual BNC input on the rear

panel of the CM6800 and is a fixed number. Within the programming screens and at the

operator level the logical number is the number used for reference.

Example of a logical numbering plan:

Physical input number

Cameras 1-5

Location in store

First floor

Logical number

11-15

Cameras 6-12

Second floor

21-27

Use the Logical Camera screen to assign new logical numbers as appropriate for your

system.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

LOGICAL CAMERA NUMBER MENU

PHY LOG PHY LOG PHY LOG

0001 17

0002 18

0003 19

0004 20

0005 21

0006 22

0007 23

0008 24

0009 25

0201 26

0202 27

0203 28

0301 29

0302 30

0303 31

0401 32

0402

0403

0404

0405

0500

0501

0502

0503

0504

0505

0601

0602

0603

0604

0605

0032

0033

0034

0035

0036

0037

0038

0039

0040

0041

0042

0043

0044

0045

0046

0047

0048

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00652

Figure 42. Access the Logical Camera Number Screen

PHY:

LOG:

The physical input number represents an actual BNC input on the rear

panel of the CM6800 and cannot be changed.

Assign a valid logical number (0001-9998) to each physical camera

input. A valid number is any number from 0001 to 9998 that has not

already been assigned to a physical camera input.

Example: In Figure 43, physical camera input 22 is assigned a

logical number of 0501. To view this camera an operator

will do the following:

1. Enter 501.

2. Press the CAM key.

Using the new logical camera number:

If you change a logical camera number in the programming menus, you cannot control the

camera until you select the camera number from the keyboard:

1. Enter the new logical camera number.

2. Press the CAM key.

The CM6800 automatically updates all other usages of the logical camera number, such as

in sequences and macros.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MACROS

Macros simplify operator control by grouping multiple functions into a single command. Use

the Macros screen to program up to 32 system macros.

MACRO MENU

PELCO SWITCHER

MODEL CM6800

MAIN MENU

MACRO 01

STP CMD

HELP

MON DWL

CAM

SWT

000

0001

0002

0003

0004

0005

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

0017

0018

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

PRES 001

— — — —000

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00653

Figure 43. Access the Macro Screen

MACRO:

STP:

Select the macro number you want to program (1-32).

Each macro can include up to 72 steps. For each step select entries for

the following fields as necessary:

CMD:

Select a command. In addition, enter a valid number in the

specified additional field(s); for example, if you select

PATT, enter a pattern number in the Command # field, a

camera number in the Camera field, and a monitor

number in the Monitor field.

Refer to Table H in the Appendix for a description of each

command and the additional fields required for each

command.

##:

If applicable, enter a valid number associated with the

command selected.

CAM:

If applicable, enter a logical camera number. To select

logical numbers other than the default numbers (1 to 48),

you must first program the logical numbering in the

Logical Camera window. Refer to the Logical Camera

Numbers section.

MON:

DWL:

If applicable, enter a monitor number.

If desired, enter a dwell time (1-99 seconds); the dwell

time is the period the macro halts before continuing to the

next step. The default dwell time is two seconds.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MACRO STATUS VIEW SCREEN

The Macro Status View screen provides a status view of each system macro (1-32). For

each active macro the current status (RUN or HOLD) and the number of the next macro

step is displayed. If a macro is not running, the status is IDLE and the step number is 00.

A system operator can display the Macro Status View screen without entering password-

protected programming screens.

MACRO STATUS

MAC

STATUS STEP

MAC

STATUS

HOLD

RUN

IDLE

STEP

RUN

IDLE

HOLD

IDLE

RUN

IDLE

PELCO VIDEO SWITCHER

MODEL CM6800

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

MACRO STATUS VIEW

RETURN

REFRESH

EXIT

Figure 44. Macro Status View Screen

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITOR DISPLAY

Use the Monitor screen to adjust monitor display settings for your system. You can adjust

settings for the current monitor only (CURRENT) or for all system monitors (ALL).

PELCO SWITCHER

MONITOR CURRENT

MODEL CM6800

MAIN MENU

CAMERA NUMBER:

CAMERA TITLE:

R/X TYPE:

MON/ALM NUMBER:

MON/ALM STATUS:

TIME:

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

DATE:

BRIGHTNESS

POSITION DISPLAY

SET ALL

RETURN

ENGLISH

RETURN

00654

00655

Figure 45. Access the Monitor Screen

MONITOR:

Select CURRENT to program the monitor display for the monitor you

are currently operating or ALL for all monitors connected to the CM6800.

If you select ALL, you must navigate left or right in the SET ALL field to

apply programming changes (refer to the SET ALL field description).

CAMERA NUMBER: Enable (ON) or disable (OFF) on-screen display of the logical camera

number.

00620

CAMERA TITLE:

R/X TYPE:

Enable (ON) or disable (OFF) on-screen display of the camera title

(maximum of 20 alphanumeric characters).

00620

Enable (ON) or disable (OFF) on-screen display of the camera

control type. The letter displayed on the monitor reflects the receiver

control type selected in the CONTROL field on the Camera screen.

R/X TYPE DISPLAY VALUES:

E = Coaxitron extended mode (32-bit)

S = Coaxitron standard mode (15-bit)

M = Genex multiplexer

P = PTZ-P (RS-422 through Control Port PTZ-A or PTZ-B)

D = PTZ-D (RS-422 through Control Port PTZ-A or PTZ-B)

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MON/ALM NUMBER: Enable (ON) or disable (OFF) on-screen display of the monitor/

alarm number. During normal operation, the monitor number

00620

appears in this field. The monitor number is a fixed number,

representing an actual BNC output on the rear panel of the CM6800.

When an alarm is active, the alarm number appears in this field. The

alarm number represents an alarm contact – the physical alarm

input number of an internal alarm contact, or the address of an

external alarm contact as configured on the Alarm Interface Unit.

MON/ALM STATUS: Enable (ON) or disable (OFF) on-screen display of the monitor or

alarm status.

00620

MONITOR STATUS DISPLAY VALUES:

Blank = normal status

H = hold

S = sequence

NOTE: If an operator presses the HOLD key while an alarm

appears on the monitor, the H does not appear. The alarm icon and

alarm status value blink to indicate the HOLD status.

0001

CAM 1

01-JAN-01 01:01:01

ALM STATUS DISPLAY VALUES:

I = internal alarm

00634

E = external alarm

V = video loss alarm

TIME:

Enable (ON) or disable (OFF) on-screen display of the time as

programmed in the system.

00620

DATE:

Enable (ON) or disable (OFF) on-screen display of the date as

programmed in the system.

BRIGHTNESS:

Select the brightness level of the on-screen display (1-8; 8 = white

characters, 1 = black characters; 2-7 = shades of gray).

If you select CURRENT in the MONITOR field, you can see the

brightness level change as you scroll through the options.

If you select ALL in the MONITOR field, the changes do not take

effect until you apply changes in the SET ALL field.

POSITION DISPLAY: Navigate left or right to select the Test Positioning Menu.

The real-time camera display appears with Test Positioning Menu

text superimposed on the screen. Use the position keys or joystick

to move the text to the desired position on the screen. The text

moves one line or character position at a time.

TEST POSITIONING MENU

---

PRESS PGM EXIT

00633

Press the PGM key to exit the test positioning menu.

SET ALL:

To apply monitor display changes to all system monitors (if you

selected ALL in the MONITOR field) you must navigate left or right in

the SET ALL field; otherwise monitor display settings are not

changed.

If you selected CURRENT in the MONITOR field, navigating left or

right in the SET ALL field has no effect.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PASSWORD

Use the Set Password screen to change the system password.

If you change the password and then forget the new one, you will have to reset the system

to the factory defaults. All system programming will be lost. Pelco recommends uploading

your programming settings to the CM6800-MGR before changing the password. This allows

you to download the previous system settings, in the event of a system reset. If necessary,

refer to the Troubleshooting section for the system reset procedure.

PELCO SWITCHER

SET PASSWORD

MODEL CM6800

MAIN MENU

OLD PASSWORD: *******

NEW PASSWORD: *******

VER PASSWORD: *******

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00656

Figure 46. Access the Set Password Screen

OLD PASSWORD:

Enter the current password (Default: 2899100). If you make a mistake

entering the old password, the message “WRONG OLD PASSWORD.

TRY AGAIN!” appears. Re-enter the old password correctly.

NEW PASSWORD: Using the numerical keypad, enter the new password. The password

must be seven digits.

VER PASSWORD:

Enter the new password again as a verification check. If you make a

mistake entering the verification password, the message “VERIFIED

PASSWORD DOESN’T MATCH” appears. Re-enter the verification

password correctly.

Once the new password is accepted, the Main Menu appears.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PORTS (SERIAL/COM PORTS)

Use the Port screen to configure the settings for each device connected to a Serial/COM

port on the rear panel of the CM6800.

PELCO SWITCHER

SET SERIAL PORT 05

MODEL CM6800

MAIN MENU

DEVICE:

TYPE:

BAUD RATE:

PARITY:

DATA BITS:

STOP BITS:

KBD300

RS485

9600

ODD

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00657

Figure 47. Access the Port Screen

SET SERIAL PORT: Select the number of the desired Serial Port/COM port (01-10).

NOTE: In the programming

screens “KBD300” is used

to refer to the KBD100,

KBD200, and KBD300

keyboards.

The serial port numbers correspond to the communication ports on

the CM6800 rear panel as follows:

Serial Port

Input on CM6800 rear panel

COM 1

NOTE: COM 1 can be accessed through a DB9

input or an RJ-45 port.

02-08

COM 2-8 RJ-45 inputs

PTZ-A control input

PTZ-B control input

DEVICE:

TYPE:

Select the device connected to the COM port; the values in the

TYPE, BAUD RATE, PARITY, DATA BITS, and STOP BITS fields

change to the settings appropriate for the specific device.

If necessary, and if allowed, select the desired communication type

(RS-232, RS-422, or RS-485).

BAUD RATE:

PARITY:

Select the desired baud rate.

Select the desired parity type.

This value cannot be changed.

DATA BITS:

STOP BITS:

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIORITY CONTROL

The CM6800 provides eight levels of priority control. Each level defines the ability of a

keyboard to control a pan/tilt/zoom (camera positioning system) and to access program-

ming screens.

Priority level applies system wide; a keyboard assigned priority level 2 on COM port 8 has a

higher priority than a keyboard assigned priority level 4 on COM port 5. A higher level

keyboard takes precedence over a lower level keyboard when the keyboards are issuing

control commands.

PELCO SWITCHER

KEYBOARD PRIORITY MENU

MODEL CM6800

MAIN MENU

PORT 05

CAMERA

KBD

PRIORITY

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00654

00658

Figure 48. Access the Priority Screen

PORT:

Select the COM port number for which you are programming priority

control.

NOTE: You can connect

only one ASCII keyboard/de-

vice per port on the CM6800

(COM port 1, 2, 4, 7, or 8).

For ASCII keyboards priority

control is based on the entry

for keyboard 1.

PRIORITY:

For each keyboard connected to the specified port, assign a priority level

(01-08).

OPTIONS:

Level 1 = highest priority

Level 8 = lowest priority

Levels 1 - 4 have the ability to access programming screens. Levels

5-8 cannot access programming screens. The lowest level or

keyboards located at the same level will access devices on first-come,

first-served basis.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SEQUENCES

The CM6800 provides two types of sequences:

•

An operator can program a scratchpad sequence from an individual monitor, without

accessing password-protected programming screens.

System sequences are password-protected and can run on any system monitor.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

SEQUENCE 01

STP CAM DWL CMD

HELP

AUX

CON

000

0001

0002

0003

0004

0005

0006

PATT

PRES

SSCN

FSCN

PRES

CAMERA

— — — —000

COFF 000

— — — —000

LOGICAL CAMERA

MONITOR

ACCESS

— — — — 00

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00660

Figure 49. Access the Sequence Screen

SCRATCHPAD SEQUENCE MON ##

STP CAM

DWL

CMD

PATT

PRES

FSCN

RSCN

SSCN

— — — — 00

AUX

CON

001

0001

0005

0008

0012

0023

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

0017

0018

PELCO VIDEO SWITCHER

MODEL CM6800

GOFF 101

CON

008

— — — —000

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

RETURN

HELP

00619

RETURN

00659

Figure 50. Access the Scratchpad Sequence Screen

SEQUENCE:

STP:

Select the sequence number you want to program (1-16).

Each sequence can include up to 72 steps. For each step select

entries for the following fields as necessary:

CAM:

Enter the desired camera number (logical number).

Enter the dwell time (01-99 seconds).

DWL:

CMD and ##:

Select a command; if you select a pattern or a

preset enter a valid pattern or preset number.

OPTIONS:

PRES = preset

PATT = pattern

RSCN = random scan

FSCN = frame scan

SSCN = stop scan

AUX and ##:

Select an auxiliary to be activated.

Global = internal and external auxiliaries.

NOTE: The auxiliaries on

the rear panel of the

CM6800 are activated by

global auxiliary numbers 1,

2, and 3.

OPTIONS:

GON = turn global auxiliary on (1-128)

GOFF = turn global auxiliary off (1-128)

CON = turn camera auxiliary on (1-8)

COFF = turn camera auxiliary off (1-8)

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

TIME AND DATE

Use the Time and Date screen to set the system time and date settings. The time and date

displayed on the monitor during real-time camera display is the time set in the memory

through this screen. The system time and date information is kept current in battery-backed

RAM. New time and date information will be set when you apply the changes (refer to the

SET TIME & DATE field description).

PELCO SWITCHER

SET TIME & DATE

MODEL CM6800

MAIN MENU

SET

MM DD YY

01 / 01 / 01

01 : 01 : 01

CAMERA

DATE:

TIME:

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

DISPLAY AS

FORMAT: DD/MMM/YY

STYLE: 24Hr

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

SET TIME & DATE

RETURN

ENGLISH

RETURN

00654

00662

Figure 51. Access the Time and Date Screen

DATE:

TIME:

Select or enter the month, day, and year of the desired system date.

Select or enter the hour, minute, and second of the desired system

time.

FORMAT:

Select the on-screen date format.

OPTIONS:

DD/MMM/YY

MMM/DD/YY

YY/MMM/DD

DD/MM/YY

MM/DD/YY

YY/MM/DD

STYLE:

Select the on-screen time format. This setting affects the on-screen

time displayed on system monitors only. System functions pro-

grammed through the event timers (refer to Event Timers in this

section) are based on 24-hour time settings.

OPTIONS:

24Hr

AM/PM (12 Hr)

SET TIME & DATE: You must navigate left or right in the SET TIME & DATE field to

apply the changes.

PATTERNS, PRESETS, AND ZONES

Special characters added through the CM6800-MGR may not be available with your

camera positioning system. Preset, pattern, and zone labels containing special characters

will appear on the monitor with blanks in place of the special characters.

Refer to the Operation section for instructions on creating patterns. Refer to your keyboard

manual for instructions on programming presets and zones.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

OVERVIEW

A brief description of CM6800 operation is provided here. Refer to the following sections for

detailed instructions and options.

Install the CM6800 and

Refer to the Installation section.

connect all system devices.

Power-up the system.

Switch monitor.

Refer to the System Start-up section.

1. Enter the monitor number.

2. Press the MON key.

Select camera.

1. Enter the camera number.

2. Press the CAM key.

Control PTZ receivers.

Use the appropriate PTZ control keys or joystick

(depending on the keyboard used).

Extended Coaxitron protocol receivers can be operated

without any programming changes. Other receiver

control protocols require programming changes.

Call a preset.

Program the preset through the keyboard.

1. Enter the preset number.

2. Press the PRESET key or Prst/Lock key

(depending on the keyboard used).

System does not function.

Refer to the Troubleshooting section.

OPERATING THE CM6800

The CM6800 can be operated with a KBD100, KBD200, KBD300, KBD960, or KBR960

keyboard. Operation instructions are provided below, but you should become familiar with

the detailed instructions provided in the appropriate keyboard manual.

The CM6800 can also be controlled with ASCII commands. Refer to the ASCII Operating

Commands section.

SWITCH MONITORS

If you select a restricted monitor, the monitor does not switch; the keyboard LED displays

the previously selected monitor number.

ALL KEYBOARDS

1. Enter the monitor number.

2. Press the MON key. The keyboard LED displays the selected monitor number.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECT CAMERAS

If you select a restricted camera view, the camera view does not appear on that monitor.

The previously selected, unrestricted camera view remains on the monitor.

KBD100/200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the camera number.

2. Press the CAM key.

1. Enter the camera number.

2. Press the CAM key.

Press the PREV or NEXT key to scroll

through the available cameras.

Press the BWD or FWD key to scroll

through the available cameras.

From the Camera Menu, select

to scroll through the available

cameras.

CONTROL RECEIVERS

Select a suitable camera and operate a PTZ function. A keyboard with “view-only” access

can view the signal from the specified camera but cannot control the camera.

Extended Coaxitron protocol receivers can be operated without any programming changes.

Other receiver control protocols require programming changes. Refer to the Programming

section.

Receiver control is not available with the KBD100 keyboard.

KBD200 KEYBOARD

Pan/Tilt/Zoom

Lens Control: Focus, Iris

Press and hold the appropriate pan/tilt key until

the camera reaches the desired position. To

change the speed of movement, press a number

(1-9) key first (1=slowest, 9=fastest).

Press and hold the appropriate

lens control key until the desired

effect is seen. To change the

speed of focus, press a number

(1-4) key, and then press the

FAR key (1=slowest, 4=fastest).

Press and hold the appropriate zoom key until

the desired effect is seen. To change the speed

of zoom, press a number (1-4) key and then

press the WIDE key (1=slowest, 4=fastest).

KBD300 KEYBOARD

Pan/Tilt/Zoom

Lens Control: Focus, Iris

Move the joystick until the camera reaches the

desired position. To increase the speed of

movement, move the joystick farther from center.

Press and hold the appropriate

lens control key until the desired

effect is seen. To change the

speed of focus, press a number

(1-4) key, and then press the

FAR key (1=slowest, 4=fastest).

Twist the joystick clockwise to zoom in,

counterclockwise to zoom out. To change the

speed of zoom, press a number (1-4) key and

then twist the joystick (1=slowest, 4=fastest).

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD960/KBR960 KEYBOARDS

Pan/Tilt/Zoom

Lens Control: Focus, Iris

Move the joystick until the camera reaches the

desired position. To increase the speed of

movement, move the joystick farther from

center or press the T key to pan at turbo speed.

Use the NEAR/FAR key to focus

near or far.

Use the OPEN/CLS key to open

or close the iris.

Twist the joystick clockwise to zoom in,

counterclockwise to zoom out. Or use the IN/

OUT key to zoom in or out.

OPERATE SEQUENCES

You can run a scratchpad sequence from an individual monitor or a system sequence on

any monitor accessible from the keyboard. When running a sequence, any cameras not

accessible to the keyboard will be bypassed.

KBD100/200/300 KEYBOARDS

Run a Sequence

KBD960/KBR960 KEYBOARDS

Run a Sequence

1. Enter a sequence number (1-16). Skip

this step to run a scratchpad sequence.

1. Select

2. Enter a sequence number (1-16

for a system sequence; 0 for the

scratchpad sequence).

2. Press and hold the NEXT or PREV key

to move forward or backward through

the sequence.

SEQ

To move through the sequence one

camera at a time:

3. Select

to start the sequence.

Press the NEXT key to move forward.

Press the PREV key to move backward.

1. Select

SEQ

Pause a Sequence

2. Select

Menu.

to enter the Sequence

1. Press the HOLD key; monitor displays H.

2. Press the HOLD key to resume.

3. Enter a sequence number (1-16).

Stop a Sequence

Select

to scroll

1. Enter a camera number.

2. Press the CAM key.

through available sequences.

to start the

4. Select

sequence.

NOTE: You can define a function key

to run a sequence. Refer to the

KBD960 Keyboard Installation/

Operation Manual for instructions.

Pause a Sequence

1. Select

2. Select

to resume.

Stop a Sequence

1. Select

1. Enter a camera number.

2. Press the CAM key.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

RUN A MACRO

KBD100/200/300 KEYBOARDS

Run a Macro

KBD960/KBR960 KEYBOARDS

Run a Macro

1. Enter the macro number.

2. Press the MACRO key.

1. Select

2. Enter a macro number.

Stop a Macro

MAC

macro.

Macro

3. Select

to start the

1. Enter the number of the running

macro.

2. Press the MACRO key.

1. Select

MAC

2. Select

Menu.

to enter the

3. Enter a macro number.

Select

to scroll

through available macros.

4. Select

macro.

to start the

NOTE: You can define a function key

to run a macro. Refer to the KBD960

Keyboard Installation/Operation

Manual for instructions.

Pause a Macro

1. Select

2. Select

to resume.

Stop a Macro

1. Select

1. Enter a camera number.

2. Press the CAM key.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACKNOWLEDGE AN ALARM

When an alarm is triggered, an alarm icon appears on the monitors programmed to show

that alarm.

KBD100/200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the monitor number.

2. Press the MON key.

1. Select

2. Select

to reset the alarm on

3. Press the ACK key. The alarm is

removed from the selected monitor.

the individual monitor.

4. Repeat for each alarm.

Select

to reset the alarm on

all monitors.

You can also select

alarm.

to mute the

NOTE: You can define a function key

to acknowledge an alarm. Refer to

the KBD960 Keyboard Installation/

Operation Manual for instructions.

CALL A PRESET

Program the preset through the keyboard. Refer to the appropriate keyboard manual for

instructions. Presets are not available with the KBD100 keyboard.

KBD200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the preset number.

2. Press the PRESET key.

1. Enter the preset number.

2. Press the Prst/Lock key.

Select the PRST icon.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CREATE AND RUN A PATTERN

Patterns are not available with the KBD100 keyboard.

KBD200/300 KEYBOARDS

Create a Long Pattern

KBD960/KBR960 KEYBOARDS

Refer to the KBD960 Keyboard

Installation/Operation manual for

instructions on creating a pattern.

1. Enter a camera number.

2. Enter 1.

3. Press and hold the PATTERN key for

two seconds.

PRST

1. Select

Menu.

to display the Preset

4. The monitor will indicate the program-

ming function is active. Move the camera

position as desired for the pattern.

2. Select

to start a pattern.

5. Press the ACK key to close the

programming function.

PRST

1. Select

Menu.

to display the Preset

to run the first pattern

Create a Shart Pattern

1. Enter a camera number.

2. Enter the short pattern number (2 or 3).

2. Enter 1.

3. Select

3. Press and hold the PATTERN key for

two seconds.

4. The monitor will indicate the program-

ming function is active. Move the camera

position as desired for the pattern.

of previously defined half-patterns.

5. Press the ACK key to close the

programming function.

PRST

1. Select

Menu.

to display the Preset

Run a Long Pattern

1. Enter 1.

2. Enter 2.

3. Select

2. Press the PATTERN key.

to run the second

3. Move the joystick or call a preset to

stop the pattern.

pattern of previously defined

half-patterns.

Run a Short Pattern

1. Enter the short pattern number (2 or 3).

2. Press the PATTERN key.

3. Move the joystick or call a preset to

stop the pattern.

OPERATE AUXILIARIES/RELAYS

Local auxiliaries are the outputs on the rear panel of the CM6800. External auxiliaries are

available by connecting an REL2064 Relay Interface Unit to the CM6800 through COM port 3.

Operate a Local Auxiliary

KBD100/200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

Auxiliary 1 relay: Press F1 to activate/

deactivate.

Auxiliary 1 relay: Press F12* to

activate/deactivate.

Auxiliary 2 TTL output: Press F2 to

activate/deactivate.

Auxiliary 2 TTL output: Press F24* to

activate/deactivate.

* F12 and F24 are the default auxiliary

control function keys; user-selected

function keys can be defined through the

Key Define Menu. Refer to the KBD960

Keyboard Installation/Operation Manual

for instructions.

NOTE: If you connect REL2064 Relay

Interface Units (up to two) to the

CM6800, operation of the two relays on

the rear panel of the CM6800-32X6 will

also operate the first two relays on the

first external unit (unless you number

the external relays starting at 64).

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operate an External Auxiliary

The CM6800 can control up to two REL2064 Relay Interface Units connected to the

system. Each unit provides 64 relays. Refer to the REL2064 Relay Interface Unit

Installation/Operation Manual for detailed information. External relays cannot be operated

with the KBD100.

KBD200/300 KEYBOARD

KBD960/KBR960 KEYBOARDS

The KBD200/300 keyboards (firmware

version 4.2 and later) can operate external

relays.

1. Enter the GPI number for the

appropriate relay output.

GPI

Refer to the KBD200 Keyboard Installation/

Operation Manual or the KBD300

Keyboard Installation/Operation Manual for

instructions.

2. Press

3. Press the desired AUX number

icon to activate the relay and

associated peripheral device.

NOTE: External relays cannot be operated

with KBD200/300 keyboard firmware

versions prior to 4.2.

(Press

to access AUX 5-8.)

MTRY

4. If

is highlighted, the operation

MTRY

is momentary. If

is not

highlighted, the operation is

latching. Refer to the KBD960

Keyboard Installation/Operation

Manual for instructions.

Operate an Auxiliary in a Receiver

Auxiliary control is not available with the KBD100.

KBD200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

Press F4 to activate.

From the Camera Menu, press

Press F5 to deactivate.

and then release to control an AUX 1

momentary function on the selected

camera.

To control a momentary function:

1. Enter the auxiliary number.

2. Press and hold F4, and then release.

Press

to control an AUX 2

momentary function. Press

access

through

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER

DISPLAYS

Multiplexer control is not available with the KBD100.

KBD200/300 KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the number of the multiplexer

input.

MUX

1. Press

to access the MUX

Control Menu.

2. Press the CAM key.

3. Press the SHIFT key. When the

SHIFT LED is lit, the keyboard can be

used to operate the following Genex

multiplexer function keys:

2. Press

to scroll through

the available MUX camera numbers.

MUX

3. Press

if necessary.

must

F1: Digital zoom

F2: PIP display

be highlighted before the system

can control Genex Multiplexer

functions.

F3: Quad display

F4: 9-screen display

F5: 16-screen display

To select a camera through the

multiplexer:

4. Move the joystick or press the

appropriate MUX control icons as

necessary for multiplexer opera-

tion. Refer to the KBD960

Keyboard Installation/Operation

Manual for detailed operation

instructions.

a. Enter the desired camera number

(1-16, based on the camera

assignments set through the

multiplexer).

b. Press the CAM key.

4. Press the SHIFT key to return to

normal keyboard operation.

When the SHIFT LED is off, you can

control the currently selected PTZ

camera through the multiplexer.

To return to camera selection

controlled by the CM6800:

a. Select the desired camera number.

b. Press the CAM key.

c. Move the joystick as necessary.

OPERATE SCANNING FUNCTIONS

Operation of the scanning functions depends on the kind of receiver or pan/tilt mechanism

you have. Refer to the appropriate keyboard manual for detailed instructions on operating

scanning functions.

DETECT VIDEO LOSS

The CM6800 detects video loss from any system camera. If video is lost from a camera,

the CM6800 blue screen appears on any monitor viewing that camera. When video is

restored to that camera, the camera view appears on the monitor(s) again. If the system is

programmed for a video loss alarm, the alarm icon appears.

DEFINE ZONES

A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera

is associated. When the associated camera is panned through or remains within this

defined zone the zone label appears on the monitor.

Refer to the appropriate keyboard manual for detailed instructions on defining zones.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

CM6800 DIP SWITCHES

00621

Figure 52. CM6800 DIP Switches – Factory Default Settings

Table G. CM6800 DIP Switch Settings

CM6800 DIP Switch

Factory Default

SW1

SW2

SW3

SW4

SW5

SW6

SW7

OFF (0) = NTSC

ON (1) = PAL

CM6800-48X8: OFF

CM6800-48X8-X: ON

RESERVED – must be in the OFF position for

proper operation

OFF

RESERVED – must be in the OFF position for

proper operation

RESERVED – must be in the ON position for

proper operation

RESERVED – must be in the OFF position for

proper operation

OFF

RESERVED – must be in the OFF position for

proper operation

SOFTWARE RESET TO FACTORY DEFAULTS

CAUTION: Resetting the software restores

the system to default settings. All user

programming is lost.

SW8

RESERVED – must be in the OFF position for

proper operation

OFF

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

MACRO COMMANDS

Table H provides a description of each macro command and the additional fields required

for each command. Refer to the Macro section for instructions on programming macros.

Table H. Macro Commands

Command

GON

Description

Specify

Field(s)

Activate an auxiliary.

Turn off an auxiliary.

Auxiliary (1-128)

Command #

GOFF

Auxiliary Notes:

•

“Global” includes both internal and external auxiliaries.

Auxiliaries on the rear panel of the CM6800-32X6 Matrix Switcher are activated by global auxiliary numbers 1, 2 and 3.

CON

Activate a camera auxiliary.

Camera auxiliary (1-8)

Camera (1-48)

Command #

Camera

Monitor (1-8)

Monitor

COFF

Turn off a camera auxiliary.

Camera auxiliary (1-8)

Camera (1-48)

Command #

Camera

Monitor (1-8)

Monitor

SEQ

Start a sequence.

Sequence (1-16)

Monitor (1-8)

Command #

Monitor

SWT

COPY

Switch a camera to a monitor.

Copy a camera view to a monitor.

Camera (1-48)

Camera

Monitor (1-8)

Monitor

Monitor (1-8) to copy from

Monitor (1-8) to copy to

Step (1-72)

Command #

Monitor

GO TO

LOOP

Go to step number specified.

Loop a macro.

Command #

0 = loop continuously

1-999 = loop the specified

number of times

MACR

?AUX

Start a specific macro.

Macro (1-32)

Command #

Check a local auxiliary; if the auxiliary is active, the

next step is executed; if the auxiliary is not active,

the next step is skipped.

Local auxiliary (1-3)

END

Exit the macro; no further steps are executed.

None

MSWT

Switch a camera connected through the multiplexer. Camera to switch (1-16)^ꢀ

Command #

Camera

Multiplexer input (1-48)

Monitor (1-8)

Monitor

PIPB

PIPF

Display multiplexer picture-in-picture view with the

designated camera in the background.

Background camera (1-16)^ꢀ

Multiplexer input (1-48)

Monitor (1-8)

Command #

Camera

Monitor

Display multiplexer picture-in-picture view with the

designated camera in the foreground.

Foreground camera (1-16)^ꢀ

Multiplexer input (1-48)

Monitor (1-8)

Command #

Camera

Monitor

^ꢀFor multiplexer functions, the camera number is the number of the video input on the multiplexer.

The multiplexer input number is the number of the video input on the rear panel of the CM6800.

(Continued on next page)

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table H. Macro Commands (Continued)

Command

Description

Specify

Field(s)

PIPO

Turn off multiplexer picture-in-picture view.

Multiplexer input (1-48)

Monitor (1-8)

Camera

Monitor

QUAD

NANO

Display multiplexer four-camera mode.

Camera group (1-4)*

Multiplexer input (1-48)

Monitor (1-8)

Command #

Camera

Monitor

Display multiplexer nine-camera mode.

Camera group (1-3)*

Multiplexer input (1-48)

Monitor (1-8)

Command #

Camera

Monitor

HEX

Display multiplexer sixteen-camera mode.

Zoom multiplexer camera view.

Multiplexer input (1-48)

Monitor (1-8)

Camera

Monitor

ZOOM

1 = zoom once

2 = zoom twice

Command #

Multiplexer input (1-48)

Monitor (1-8)

Camera

Monitor

AAI

Arm internal alarm.

Internal alarm (1-8)

External alarm (1-128)

Command #

DAI

Disarm internal alarm.

AAE

DAE

AAV

Arm external alarm.

Disarm external alarm.

Arm video loss detection for a camera.

Physical camera number (1-32)

Logical camera number

Camera

DAV

Disarm video loss detection for a camera.

Start a pattern.

Physical camera number (1-32)

Command #

Logical camera number

Camera

Command #

Camera

Monitor

PATT

Pattern (#)**

Camera (1-48)

Monitor (1-8)

Preset (#)**

PRES

Start a preset.

Command #

Camera

Monitor

Camera (1-48)

Monitor (1-8)

Camera (1-48)

Monitor (1-8)

Camera (1-48)

Monitor (1-8)

Camera (1-48)

Monitor (1-8)

RSCN

FSCN

SSCN

Start a random scan.

Start a frame scan.

Stop a scan.

Camera

Monitor

Camera

Monitor

Camera

Monitor

* Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual for information on multiple

camera displays.

** The number of patterns and presets available is determined by the camera positioning system. Refer to the appropriate camera

positioning system manual.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

ASCII OPERATING COMMANDS

ASCII protocol uses the ASCII character set to transmit and receive commands between a

personal computer (PC) and the CM6800. The commands are readable but are not English.

ASCII commands control the pan and tilt mechanisms (fixed and variable speed), camera

functions, auxiliary relays, and alarms.

The ASCII protocol communicates in a standard asynchronous, byte-oriented protocol that

includes: 1 start bit, 8 data bits, 1 parity bit (odd parity), and 1 stop bit. The default

communication rate is 9600 baud.

A lowercase “a” ends each command. The ASCII translator acknowledges accepted

commands and rejected commands with the following responses:

AKa

NAa

command accepted

command rejected or the ASCII translator does not recognize the command

If the command requires a numeric value, enter the number first.

Table I provides examples of ASCII commands. Table J lists all of the commands.

Table I. Examples of ASCII Commands

Functional Procedure

Commands

Result

Select a pan and tilt

device labeled

3Ma16#a

Switch camera 16 to currently selected

monitor 3.

“CAMERA # 16” and

switch it to monitor # 3.

Manipulate the pan

and tilt device.

1Ma3#a

Switch camera 3 to monitor 1.

5Ma2#a3\a

47Ra33Da

Go to camera 2, preset 3, on monitor 5.

Pan right at speed 47, tilt down at speed 33.

Stop all image motion.

Switch a camera.

Call a preset.

Pan and tilt.

1Ma3#a

Switch camera 3 to monitor 1.

5Ma2#a3\a

47Ra33Da

Go to camera 2, preset 3, on monitor 5.

Pan right at speed 47, tilt down at speed 33.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table J. ASCII Commands

Number ranges are enclosed in brackets – do not enter the brackets. When you control a fixed speed pan and tilt, omit the speed

information.

Result

Desired Action

Command

Calls a monitor to use for camera operation.

Select monitor

[1-9999]Ma

Selects a camera to display on the current operating monitor. The

NEXT key (+) and PREV key (-) commands switch to the next

numbered camera in the system.

Select camera

Next camera

Previous camera

[1-9999]#a

-a

Starts the selected sequence going forward (incrementing camera

numbers).

Start a sequence forward

Start a sequence backward

Hold a sequence

[1-99]qa

[1-99]ba

Starts the selected sequence going backward (decrementing camera

numbers).

Places the running sequence on hold, freezing the currently selected

camera on the monitor. It lets you control the camera or switch. The

sequence is still “armed” on the monitor, but inactive.

Places the running macro on hold.

Hold a macro

[1-32]ea

Moves the currently selected pan and tilt device left or right at the speed

indicated. If you omit the speed, some devices move at their default

speed and others move at their slowest possible speed. Speed

information has no effect on fixed speed devices.

Pan left

Pan right

Stop pan left

Stop pan right

[1-64]La

[1-64]Ra

~La

~Ra

Moves the currently selected pan and tilt device up or down at the

speed indicated. If you omit the speed, some devices move at their

default speed and others move at their slowest possible speed. Speed

information has no effect on fixed speed devices.

Tilt up

[1-63]Ua

[1-63]Da

~Ua

Tilt down

Stop tilt up

Stop tilt down

~Da

Makes the currently selected camera zoom in (close up view) or zoom

out (wide view).

Zoom telephoto

Zoom wide

Stop zoom telephoto

Stop zoom wide

~Ta

~Wa

Changes the good focus range nearer or farther on the currently

selected camera.

Focus near

Focus far

Stop focus near

Stop focus far

~Na

~Fa

Opens (brighter image) or closes (darker image) the iris on the

currently selected camera.

Iris open

Iris close

Stop iris open

Stop iris close

~Oa

~Ca

Stops all image motion (stops pan, tilt, zoom, focus, and iris). Does not

stop a pattern.

Stop all PTZ motion

On receivers that do patterns, these commands let you record your

motions and operations (for a limited time) and then have the system

repeat them.

Record pattern

Execute pattern

End pattern

[1-99]/a

[1-99]pa

[1-99]na

Recalls a stored preset position.

Go to preset position

Set preset with a label

[1-99]\a

Sets a preset location with an embedded label, where the ASCII string

must be UPPERCASE characters.

la[string]!a

[1-9999]^a

The [string] is an alphanumeric label up to 20 characters long and

[1-9999] is the associated preset number.

NOTE: All transmitted characters must be ASCII.

Sets a preset location without an embedded label.

Begins a zone without a label.

Set preset without a label

Begin zone

[1-9999]-^a

[1-8](

Begins a zone with an embedded label. The ASCII string must be

uppercase characters.

Begin zone with a label

la[string]!a[1-8](

Ends the zone program

End zone

[1-8])

These commands start and stop scans.

Begin random scan

Begin frame scan

Stop scan

(Continued on next page)

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table J. ASCII Commands (Continued)

Command

Result

Desired Action

[1-128]xa

[1-128]~xa

Auxiliaries are relay outputs that can be controlled through the protocol 1-3

operate the AUX 1-2 and F3 auxiliaries on the rear panel of the CM6800

(and the first three auxiliaries on an external REL2064). 4-128 operate the

external auxiliaries on up to two REL2064 Relay Interface Units.

Auxiliary on

Auxiliary off

[1-8]Aa

[1-8]Ba

Operates auxiliaries at the camera (receiver).

Camera auxiliary on

Camera auxiliary off

[1-32]Sa

[1-32]Ha

[1-9999]Ia

Starts the selected macro.

Start macro

Stops the selected macro.

Stop macro

Acknowledges an existing alarm.

These commands arm and disarm system alarms.

Acknowledge alarm

[1-8]Ji

Arm internal alarm

[1-128]Je

[1-48]Jv

[1-8]~Ji

[1-128]~Je

[1-48]~Jv

Arm external alarm

Arm video loss alarm

Disarm internal alarm

Disarm external alarm

Disarm video loss alarm

[1-48]Ya[string]!a

Sends a camera title to the matrix switching system. You can only send

one camera title at a time.

Send camera title

Valid characters in the string are A-Z, a-z, space, and 0-9 in ASCII

representation. Strings are limited to 20 characters.

Returns the version number of the device.

Version

ZaMM/DD/YY/HH:

MM:Ssa

Sets the date and time. Since the date and time string could be

confused with other commands, the command Za comes first. This puts

the receiving device into a mode that can accept the specialized string.

Set date and time

NOTE: All transmitted characters must be ASCII.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

NOTE: There are no user-

serviceable parts inside the

CM6800. Only authorized

service personnel may open

the unit.

GAINING INITIAL CONTROL

If you are having problems gaining control of your system for the first time:

•

Confirm that all system equipment is plugged in and has power.

Confirm that each keyboard and peripheral device in your system has a unique local

address. Refer to the Switch Settings section in the appropriate keyboard manual.

•

Be sure data cables have not been mixed up.

Cycle the data cable to the keyboard:

1. Unplug the data cable from the rear of the keyboard.

2. Plug the data cable back into the rear of the keyboard.

3. WAIT AT LEAST FIVE SECONDS.

4. Select a monitor.

If you still cannot gain control of the system:

•

Confirm the wiring is correct and the user-supplied cable between wall jacks is

appropriate for the application.

•

Confirm that when the keyboard data cable is cycled, the keyboard LED flashes

momentarily (indicating power).

If you still cannot gain control of the system, call Pelco’s 24-hour technical support at

1-800-289-9100 or 1-559-292-1981.

SOFTWARE RESET

Pelco strongly recommends uploading

CAUTION:

Resetting the soft-

ware restores the

system settings to the CM6800-MGR before

the software reset – this will allow you to

restore system settings after the software

reset.

ALARM

system to default settings.

CONTROL

PTZ

1. Remove the two screws and the DIP

switch cover plate from the rear of the

switcher.

OUT

COM

2. Move DIP switch 7 to the ON position

(to “0”).

120/230~

50/60 HZ

25 WATTS

3. Cycle power.

00623

DIP SWITCH

COVER PLATE

The switcher will go through a

software clear cycle and reset to

factory defaults.

Figure 53. DIP Switch Cover Plate

4. Move DIP switch 7 to the OFF position.

Failure to move DIP switch 7 to the

OFF position could result in loss of

system settings during a power

outage.

00622

5. Re-initialize keyboards by entering

the monitor number and then

pressing the MON key.

DIP SWITCH 7:

ON = SOFTWARE RESET

OFF = NORMAL SYSTEM

OPERATION

6. Download your previous system

settings (revise settings as

Figure 54. CM6800 DIP Switch 7

necessary) from the CM6800-MGR.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SOLUTIONS TO COMMON PROBLEMS

Refer to Table K for a list of common problems and their solutions.

Table K. Solutions To Common Problems

Problem

Remedy

CM6800 does not have power.

Make sure the power cord is plugged in.

You can see some cameras and not

others from your location.

Confirm that the camera is properly connected and has power.

The keyboard and monitor may have been denied access to the cameras.

The CM6800 does not respond to

keyboard commands.

Confirm that the monitor the keyboard is addressing is the same as the monitor in

front of you.

Access to that monitor may be restricted from that keyboard. Select another

monitor.

Pressing the PGM key displays a P on

the keyboard LED, but the Password

menu does not appear on the monitor.

(KBD100/200/300 Keyboards only)

Confirm that the keyboard transformer is plugged in and all electrical connections

are in order.

Confirm that the monitor the keyboard is addressing is the same as the monitor in

front of you.

Keyboards do not function after

installation and initial power-up.

Confirm that all wiring is correct and that keyboards have power and are connected.

Confirm that each keyboard has been set for a unique address.

Previous system control has been lost.

SOLUTION 1

Initialize the keyboard:

1. Enter the monitor number.

2. Press the MON key.

SOLUTION 2

1. Unplug the data cable from the rear of the keyboard.

2. Plug the data cable back into the rear of the keyboard.

3. Wait five seconds.

4. Re-initialize the keyboard.

SOLUTION 3

1. Power down the CM6800.

2. Power up the system.

3. Wait five seconds.

4. Re-initialize keyboards.

SOLUTION 4

Perform a software reset (refer to Software Reset in this section).

CAUTION: Resetting the software restores the system to default settings. All

user programming is lost. Uploading system settings to the CM6800-MGR

before the software reset allows you to restore system settings after the software

reset.

SOLUTION 5

Call Pelco’s 24-hour technical support at 1-800-289-9100 or 1-559-292-1981.

The unit malfunctions and you cannot

restore it to satisfactory operation.

Perform a software reset (refer to Software Reset in this section).

CAUTION: Resetting the software restores the system to default settings. All

user programming is lost. Uploading system settings to the CM6800-MGR

before the software reset allows you to restore system settings after the software

reset.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD960/KBR960 ICON/BUTTON LEGEND

LOG

OFF

JOYSTICK

ADJUST

MUX

LOG

OFF

JSTK

ADV

AUX 4, RELAY 4

AUX 5, RELAY 5

AUX 6, RELAY 6

AUX 7, RELAY 7

AUX 8, RELAY 8

QUAD

LOG OFF

YES

ADVANCE

MENUS

MUX

NINE

YES

LOG OFF

SERIAL PORT

TEST

MUX

SIXTEEN

SETUP/DEFINE

KEYBOARD

DOWNLOAD

MUX

LIVE

SAVE

SELECTION

KEYBOARD

UPLOAD

MUX

CAMERA CONTROL

RESET

ALARM

TEST GRAPHIC

PAGE 0

SEQUENCE

DEL

DELETE

SEQ

RESET

ALL ALARMS

CAMERA

PRESET

TEST GRAPHIC

PAGE 1

PRST

TEST GRAPHIC

PAGE 2

MUTE

EXIT

PATTERN

ZONE

CAMERA

SELECTION

TEST TEXT

PAGE 0

ALARM

MONITOR

DEFINE

GPI

MTRY

MAC

DEF

PARITY

SELECTION

SCROLL UP

SCROLL FIELD UP

RELAY

MOMENTARY

DIP SWITCH

TEST

PROGRAM

PGM

SCROLL DOWN

SCROLL FIELD DOWN

MACRO

SELECT

DISPLAY

BRIGHTNESS

DEFINE

NUMBER

DEF

LCD

NUM

PLAY FWD

DEVICE

PAUSE

PROGRAMMING

COM1

COM2

COM3

COM PORT 1

SCROLL RIGHT

PLAY BWD

SCROLL LEFT

COM PORT 2

STOP

SCROLL OPTION

MUX

COM PORT 3

MUX

SCROLL OPTION

DOWN

MUX

AUX 1, RELAY 1

AUX 2, RELAY 2

AUX 3, RELAY 3

TAPE

KEYBOARD

SELECT

MUX

ZOOM

KEYBOARD

KEY TEST

MUX

PIC IN PIC

IN/OUT

FUNCTION

CONTROLS

FORWARD

RUN

BACKWARD

MACRO

RECALL/ALTERNATE

PRESET/LOCK

OTHER

CONTROLS

CAMERA

MONITOR

TURBO

IRIS

CONTROLS

NEAR/FAR

OPEN/CLOSE

ESCAPE

00665

Figure 55. Icon/Button Legend

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

GLOSSARY

Term

Definition

Access

The CM6800 allows you to restrict system control by (1)

limiting the monitors or cameras a keyboard can access,

or (2) limiting the cameras that can be viewed on a

monitor.

Alarm display format

Alarm group

The CM6800 Matrix Switcher provides four formats for

displaying alarmed cameras on system monitors: Block

Build, Chronological Pair, Reverse Chronological Pair,

and Salvo Group.

To display on a monitor, an alarm must be assigned to

one or more alarm groups. The CM6800-48X8 Matrix

Switcher provides eight alarm groups (A through H). The

CM6800-32X6 Matrix Switcher provides six alarm groups

(A through F). Refer to Alarm Groups and Alarm Group

Display Options.

Alarm priority

A priority alarm appears on system monitors before a non-

priority alarm. Refer to the Priority description under

Internal and External Alarms.

ASCII

The binary, 7-bit, 128-character set implemented as the

standard in communications.

Auxiliary

Output relays can be used to control external devices

based on matrix switcher activities. External devices can

include VCRs, alarm devices, and triggers for audio

circuits.

Baud rate

Bit

In video, the greater the speed, the larger amount of

information passed. In digital systems, this capacity is

given in bits per second, or baud rates.

An abbreviation for “binary digit” - the smallest unit of

information a computer can use. A bit is either a 1 or a 0

(a high or low voltage state).

Byte

An abbreviation for “binary term” – bytes are strings of

bits, operated upon as a unit. A byte is equal to eight bits

(256 possibilities) and is large enough to hold one

character (like an “A” or the number “1”.)

Camera auxiliary

Coaxitron

Some cameras contain an auxiliary output relay, which

can be used to operate a device connected to the relay.

This is Pelco’s “up the coax” control technology. Control

signals are sent back up the coaxial cable that the video

signal travels down on.

COM port

This is a communication port input on the rear panel of the

matrix switcher.

Daisy-chain

This is a way of providing multiple connections in a series,

from one source. A daisy-chain configuration connects

multiple, linked devices from one output. When connecting

PTZ cameras to a matrix switcher, for example, one set of

cables connects the matrix switcher to each receiver, and

then each receiver is connected to the next receiver.

Dwell

This is the amount of time something happens in the

system, such as the amount of time a camera view

displays on a monitor, or an auxiliary is on.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Event timer

The matrix switcher can automatically initiate macros or

sequences based on time and date.

Extended Coaxitron

Frame scan

This is Pelco’s Coaxitron control technology that uses 32

bits to send a command.

A three-second camera scan followed by a three-second

pause.

Latching operation

Logical camera number

The auxiliary device remains on until a command is given

(by a system operator or system automation) to turn it off.

A user-selectable, variable number, which is associated

with an actual physical camera input on the rear panel of

the matrix switcher.

Macro

A sequence of commands or steps. Macros can be

operated automatically or manually. Automatic operation

can be based on specific times or dates (set through the

Event Timer).

Matrix switcher

This is also known as a cross-point switcher. The cross-

points are actually electronic switches that select any

video input onto any video output at any one time,

preserving the video impedance matching. One video

signal can simultaneously be selected on more than one

output. More than one video input can be selected on one

output, in a sequential switching between inputs (unless

the input is routed through a multiplexer, which allows

more than one input to be viewed on the output monitor at

any one time).

Momentary operation

Multiplexer (MUX)

The auxiliary output operation is activated briefly and then

turns off.

A multiplexer allows an operator to view more than one

video signal (usually either four, nine or sixteen signals) at

one time on a single monitor. A multiplexer can also send

these multiple images to the video recorder, switching

rapidly between image from each camera.

NTSC

The American color TV standard, used in North America,

Japan, and a few other countries. It specifies 525 lines/

screen, and 29-30 frames/sec.

Null modem cable

A null modem cable allows you to connect your PC to

another nearby PC or serial device by “crossing over”

(reversing) their respective pin contacts. (A null modem

cable is limited to 30 feet in length.)

PAL

The color TV standard (50Hz) used by European, Asian,

and some Latin American countries. It specifies 768

pixels/line, 576 lines/screen and 25 frames/sec.

Parity type

The parity bit is used to identify whether the bits being

moved arrived successfully. Parity bit checking can be

based on odd or even bits. No parity means that a parity

bit is not transmitted or checked.

Partitioning (access)

The CM6800 allows you to restrict system control by (1)

limiting the monitors or cameras a keyboard can access,

or (2) limiting the cameras that can be viewed on a

monitor.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Pattern

A pattern is a user-defined, viewable camera path with a

definite beginning and end. The pattern can consist of any

standard pan and tilt or lens command. Once defined, the

pattern is easily activated by a system operator or through

an automated event. The pattern will run continuously until

it is deactivated. The number and time length of patterns

varies with different positioning systems.

Physical input

Preset

A number representing an actual BNC camera input on

the rear panel of the matrix switcher. This number cannot

be changed.

A preset allows operators to direct a PTZ (camera

positioning system) to move to a predetermined scene on

keyboard command or as a result of an alarm. In addition

to moving the camera, a descriptive title can appear on

the screen. The type of camera positioning system

determines the number of presets available.

Priority control

PTZ

This is the level of priority a system keyboard has to

control a PTZ camera positioning system and to access

CM6800 Matrix Switcher on-screen programming menus.

This is a camera positioning system with pan, tilt, and

zoom capabilities.

Random scan

This is a camera scan moving in a random pattern.

RJ-45 wall block

This is a wall block with eight terminals for connecting

RS-232, RS-422, and RS-485 communication lines. (This

is Pelco part number CON12J00820360Z.)

RS-232

RS-422

This is an Electronics Industry Association (EIA) interface

standard used for data communication; the normal

connection distance is 50 feet (15 m). Pelco uses this

standard for communication from a controller to a PC or

RS-232 network. The Pelco three-wire connection

provides one wire for transmit, one wire for receive, and

one wire for common.

This is an Electronics Industry Association (EIA) interface

standard. Pelco uses this standard for communication

from a controller to one or more camera receivers (on the

same line); the maximum recommended distance is 4,000

feet (1,219 m).

The four-wire connection provides two wires for transmit

and two wires for receive. Pelco receiver/driver

communication uses only the two transmit wires

(commands are sent from the controller to the receiver

only; the receiver does not “talk” back to the controller).

Pelco keyboard communication uses all four wires.

NOTE: The electrical communication scheme used by

Pelco is a direct-coupled method, not an AC-coupled

method. Therefore, if the ground potential of the wire at its

two end points is different (other than zero volts), an

additional wire is required as a ground.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-485

This is an Electronics Industry Association (EIA) interface

standard used for communication between multiple

transmitters and receivers; the maximum recommended

distance is 4,000 feet (1,219 m). The four-wire connection

provides two wires for transmit and two wires for receive.

NOTE: The electrical communication scheme used by

Pelco is a direct-coupled method, not an AC-coupled

method. Therefore, if the ground potential of the wire at its

two end points is different (other than zero volts), an

additional wire is required as a ground.

Scratchpad sequence

A scratchpad sequence can be run on an individual

system monitor, without entering the password-protected

CM6800 Matrix Switcher on-screen programming menus.

You can program scratchpad sequences from the

CM6800 Matrix Switcher on-screen programming menus

only, not from the CM6800-MGR software.

Sequence

Allows an operator to see a routine of 72 camera views on

any system monitor, over and over again. The sequence

can be operated automatically or manually. The order in

which the camera views appear and the time each view

remains can be programmed.

Standard Coaxitron

Star configuration

This is Pelco’s Coaxitron control technology that uses 15

bits to send a command.

This is a way of providing multiple direct connections from

one source. A star configuration uses a separate cable for

each direct connection, with all of the cables connected to

a central device. When connecting PTZ cameras to a

matrix switcher, for example, the central device can be a

code distribution unit, such as the CM9760-CDU-T. Each

camera has a direct connection to the CM9760-CDU-T,

which is the central device.

Synchronize

Since the CM6800 Matrix Switcher can be programmed

from either the CM6800-MGR software or the CM6800

Matrix Switcher on-screen programming menus, you could

potentially have different settings in the two programming

sources. Pelco recommends transmitting any

programming changes from the updated programming

source so that the next time you make changes from

either programming source, you will be modifying the

current system settings. Refer to Transmitting

Programming Settings.

System keyboard

This is a keyboard compatible with and connected to the

matrix switcher, allowing a system operator manual

control over the system.

System reset

This restores the system to the default settings, as

shipped from the factory.

Vertical drive/synchronization

This option sends a timing pulse from the matrix switcher

to a compatible camera. The camera aligns the vertical

synchronization with the timing pulse.

Zone

A zone is a user-defined, physical location to which (1) a

label is attached and (2) a camera is associated. When

the associated camera is panned through or remains

within this defined zone, the zone label appears on the

monitor. With some camera systems, a zone can be

blanked to prevent viewing while the camera is positioned

in the zone.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL

Memory Protection:

Lithium battery, two weeks of data protection

Keyboards:

Eighteen: Sixteen KBD100/200/300 Series keyboards and two

KBD960/KBR960 Series keyboards. (Switcher can provide

power for two KBD100/200/300 Series keyboards. Additional

keyboards will require a remote power supply.)

Receiver/Dome Control:

Alarm Inputs:

Coaxitron and RS-422

Eight individually programmable for N.O. or N.C. on rear

panel (plus an additional 128, via ALM2064, Alarm Interface

Units, providing a total of 136 possible)

Control Outputs on Rear Panel

AUX 1, 2:

Two relays (SPDT), rated at 0.5 amp @ 125V, 1 amp @

30 VDC, 60 milliohms contact resistance

F3:

One open collector (TTL); 15 VDC maximum, 25 mA maximum

Additional Outputs:

Two REL2064, Relay Interface Units, may be connected to

expand relay outputs to a maximum of 128

Communication Ports:

Eight data ports, two PTZ control ports, all programmable by

the user; two ports provide power for keyboards

ELECTRICAL

Input Power:

Power Consumption:

120V or 230V, 50/60Hz

25W

SWITCHER CHARACTERISTICS

Video Inputs, Looping: 40 BNC, terminating or looping (individually selectable per

camera), .5 to 2.0 Vp-p composite video, video loss detection

Video Inputs, Terminating: Eight, BNC, terminating, .5 to 2.0 Vp-p composite video, video

loss detection

Video Outputs:

Switching Type:

Switching Method:

Switching Time:

VIDEO

Six or eight outputs, BNC

Cross-point video matrix, NTSC and PAL compatible

Vertical interval switching

Less than 16 milliseconds (typical)

Bandwidth:

15 MHz

Frequency Response:

Signal-to-Noise Ratio:

Flat to 8 MHz, ±1dB to 13 MHz

-50 dB (peak-to-peak vs. RMS noise)

Adjacent Channel Crosstalk: -55 dB typical at 3.58 MHz

Differential Gain:

Differential Phase:

Gain:

0.03% typical

0.24° typical

Unity (±1dB)

Zero volts

DC Output:

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

CHARACTER GENERATION

Character Type:

White with black outline; adjustable brightness

Camera Identification:

Two lines, twenty-character title, plus camera number,

monitor number, date (four formats) and time (24-hour or AM/

PM formats)

Programmable:

On-screen, menu-driven

128 ASCII characters

Character Set:

ENVIRONMENTAL

Ambient Operating

Temperature:

Humidity:

20° to 120°F (-7° to 49°C)

10-90% non-condensing

MECHANICAL

Dimensions:

17.40 (W) x 5.25 (H) x 12.25 (D) inches (without rack ears)

(44.20 x 13.34 x 31.12 cm)

Mounting:

Factory-configured for EIA rack mount (3 RU); rack ears can be

removed for versatile wall mount or freestanding applications

Unit Weight:

12.7 lb (5.76 kg)

(Design and product specifications subject to change without notice.)

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

REGULATORY NOTICES

This equipment has been tested and found to comply with the limits of a Class B digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that the interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try and correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

Exceptions to this warranty are as noted below:

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual #

C1515M

Date

5/01

8/01

11/01

Comments

Original version.

Updated certifications.

C1515M-A

Revised manual to describe updated functionality in the software.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Windows is a registered trademark of Microsoft Corporation.

Endura and ExSite are trademarks of Pelco.

Pelco Manual C1515M-A (11/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Stereo Amplifier UA 35T II User Manual
Philips Digital Photo Frame SPF3410 G7 User Manual
Philips DVD Player SACD1000 User Manual
Philips Home Theater System DCK3060 User Manual
Pioneer Cassette Player CT W208R User Manual
Plinius Audio Stereo Amplifier Hautonga Intergrated Amplifier User Manual
Polaroid Portable DVD Player PDV 0813A User Manual
Polycom Video Games VVX500 User Manual
Porter Cable Saw 7724 User Manual
Precor Fitness Equipment Ab X100 User Manual