Pioneer Indoor Furnishings PWM T210 User Manual

PWM-T210  
Installation Instructions  
UNIVERSAL FLAT PANEL MOUNT  
IN-PWMT210.R0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Safety Precautions  
This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation specialists or your dealer should  
install the mount and set up the plasma display in order to avoid personal injury or property damage. Premier does not assume liability for injury or damage,  
including liability, caused by improper installation, mounting or setup of the plasma display, misuse, modification or natural disasters.  
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation.  
The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an  
easily accessible location for future reference.  
The wall being considered for mounting must be capable of supporting at least five (5) times the weight of 40Kg. If it is not, the wall must be reinforced before  
beginning installation.  
Only use specified parts for the installation of the mounting bracket. Do not use the mounting hardware from any other mount or any other source.  
Warning Statements  
The wall or ceiling structure must be capable of supporting at least five (5) times the weight of the plasma display. If not, the wall or ceiling must be reinforced.  
Proper installation procedure by qualified personnel as outlined in the installations instructions must be followed. Failure to do so could result in serious personal  
injury.  
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation.  
The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an eas-  
ily accessible location for future reference.  
Safety precautions must be taken at all times.  
Handling by other than professional contractors is prohibited.  
Warning and caution in general.  
Indicates that the power plug is to be disconnected from the power outlet.  
Contact Premier Mounts for any technical/installation questions.  
Disassembly of the plasma display is prohibited.  
Installation Location  
Make sure the plasma display mounting area is completely free of  
A secured structure wooden stud wall must always support the weight or load  
internal or external wires, pipes, gas lines, phone lines, etc. Failure to do  
of the plasma display. Always confirm the center of the wood stud before  
so may result in injury and damage to the walls, wiring or piping system.  
beginning the installation. Failure to do so could result in personal injury and  
Do not block the ventilation holes. Sufficient clearance must be left in the  
area surrounding the plasma display and wall mount to avoid blocking  
the vents and causing the plasma display to overheat which could cause  
physical damage.  
Avoid installing the plasma display in locations where temperatures and  
humidity are excessively high, or contact with any water or vapors possible.  
This could result in fire, electrical shock and damage to the plasma display.  
Water will damage the wall structure for wall mount installation.  
The permissible temperature is (0-40ºC) and humidity is (20%-80%).  
a
risk of fire. Leave 100mm or more away from all of the  
surrounding four sides for proper airflow.  
Do not install in locations where there is vibration, movement or danger  
of impact. Failure to do so could result in plasma display cracking or  
falling from the wall causing damage and injury.  
The mount is designed to be used on vertical walls only. Do not install near or  
on doors, angled ceilings, walls, or any other installations other than wall  
mounting. Failure to do so could result in damage and injury. This wall mount  
is to be used only with  
plasma display other than Pioneer is prohibited and may cause injury and dam-  
age.  
Do not install near heater, fireplace, direct sunlight or air conditioning or  
any other source of direct heat energy. Failure to do so may result in  
damage to the plasma display and could cause a risk of fire.  
It is not necessarily to open the plasma display prior to installation. Never  
open the plasma display or modify the mount. This mount is to be used  
only as outlined in the installation instruction. Failure to do so may result  
in damage and injury. If a malfunction or problem occurs with the plas-  
ma display display, contact the nearest dealer or Pioneer.  
a
Pioneer plasma display. Use with any  
Avoid Installations where there is danger of contact with over excessive dust,  
oil smoke, and tobacco smoke. Failure to do so may result in fire or damage  
to the plasma display or its internals.  
Safety Precautions  
At least two qualified people should always perform the installation work.  
Injury and damage can result from dropping or bending the plasma display.  
All bolts must be properly tightened and secured before installing the  
plasma display. Failure to do so could result in the plasma display falling  
causing damage to the plasma display and personal injury.  
All hardware must be firmly tightened and secured to the plasma display in  
the correct locations. If the hardware is not properly installed, do not hang the  
plasma display to the wall mount. Damage and injury could result from the  
plasma display falling down.  
Objects on the wall may collect dust quicker than anticipated. Check  
periodically for dust accumulation. Refer to the plasma display installa-  
tion instructions for cleaning instructions.  
Do not play around the plasma display or throw any objects near or at  
the screen. The screen is very sensitive and may scratch or break or  
cause the plasma display to fall from the wall causing personal injury  
and damage.  
All four (4) Lag bolts must be properly secured to the wall studs. The lag bolts  
must always be secured through the center of the wood studs. Failure to do so  
could result in the plasma display falling from the wall causing damage to the  
plasma display and personal injury.  
Installation Instructions  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Parts List  
NOTE:  
This mount is shipped with all installation hardware and components. Make sure that none  
of these parts are missing and/ or damaged before beginning installation. If there are parts  
missing and/or damaged, please stop and contact Premier Mounts (800) 368-9700.  
5/16" x 3" Lag Bolts  
(Qty 8)  
Wall Plates (Qty 2)  
5/16" Flat Washers  
(Qty 8)  
Mounting Brackets  
(Qty 2)  
M6 x 30 Lateral Shift  
Locking Screws  
(Qty 2)  
Griplates™  
(Qty 6)  
Template (Qty 1)  
M6 x 12 Safety Knobs  
(Qty 2)  
M6 x 12mm Phillips  
Head Screws (Qty 4)  
M8 x 20mm Phillips  
Head Screws (Qty 6)  
Installation Tools  
Phillips Head Screw Driver Soft Material/ Blanket  
1/2" Socket and Wrench  
Level (Supplied)  
1/4” Drill Bit  
Pencil  
Tape Measure  
Drill Gun  
Stud Finder (Commercially Available)  
Page 4  
Installation Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Locating the Center of the Display  
CAUTION: Proper installation procedure by qualified personnel as outlined in the installation  
instructions must be adhered to. Failure to do so could result in serious personal injury and  
possible damage to the flat panel.  
WARNING: INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SURFACE TO PREVENT  
DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO DO SO  
WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON  
THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. THE FLAT PANEL IS  
HEAVY AND FRAGILE. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY  
RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO  
COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT  
PANEL.  
Inverted  
Display  
Inverted  
Display  
Marking the  
Center of the  
Display  
Display  
Top  
Tape  
Measure  
C
L
Display  
Bottom  
C
L
Figure 2  
Figure 1  
2. Using a pencil lightly mark the  
center of your flat panel  
(Figure 2).  
1. Once the flat panel is inverted, use a  
measuring tape to find the center of  
your flat panel measuring from  
outside to outside of the chassis  
(Figure 1).  
Mounting Bracket Positioning  
Left  
Mounting  
Bracket  
Display Bottom  
Right  
Mounting  
Bracket  
Arrows Facing  
Out  
Figure 3  
3. Lay the left and right mounting brackets  
over the mounting points, with the stamped  
arrows facing out (Figure 3).  
Installation Instructions  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Display  
Bottom  
C
L
Mounting Bracket  
Align the  
Mounting  
Brackets  
Viewing  
Guide  
Center  
Center of  
Display  
Display  
Bottom  
Figure 4  
Figure 5  
4. Match the center of viewing guide  
with the center line you marked in  
step 1 (Figure 4).  
5. The mounting brackets are designed  
with a center of viewing guide on the  
side of them (Figure 5).  
Securing the Mounting Brackets  
The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires.  
NOTE: Your plasma uses M8 x 20 or M6 x 12 Phillips screws, use the M8, or M6, mounting points.  
1. Once the mounting brackets are aligned secure the Griplate™ to the flat panel (Figure 6).  
NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing  
down.  
2. Pre-install two (2) M6 x 30 (mm) Phillips pan screws to the bottom of the left and right hand side  
mounting brackets.  
Screwdriver  
DIMPLES  
FACING UP  
M4  
M5 M6  
M8  
DIMPLES  
FACING UP  
DIMPLES  
FACING DOWN  
Display Bottom  
DIMPLES  
FACING DOWN  
Figure 6  
Page 6  
Installation Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Marking the Wall  
Viewing Port  
Center  
Mark the Wall  
VIEWING PORTS  
CENTER OF  
VIEWING LINE  
Wall Structure  
MARKING THE  
LINE  
Figure 8  
Figure 7  
1. Align the center viewing port from the  
carton template to the wall. Match the  
center of viewing port to the center of  
viewing height desired (Figure 7).  
2. Mark a line on the bottom of the  
carton template (Figure 8).  
Marking the Bottom Mounting Points  
CAUTION:  
The lag bolts must be secured to the center of a stud. Use a commercially available stud finder to locate the studs  
nearest to your center viewing mark.  
Pilot Holes  
Drill Gun  
16"  
Wall Plate  
Level  
Mounting Slots  
Wall Structure  
Figure 9  
Figure 10  
1. Place the upper portion of the bottom wall  
plate to the reference line and mark the four  
(4) lag bolt mounting points through the  
wall plate slots on the wall (Figure 9).  
3. Pilot holes are recommended. Use a 1/4”  
drill bit to drill where your markings are  
located (Figure 10). These pilot holes  
will be for the lower mounting plate.  
2. Level the wall plate with the reference  
arrow pointing up to the ceiling.  
Installation Instructions  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Securing the Lower Wall Plate  
Marked Wall  
Level  
Wall Plate  
Wall  
Plate  
Template  
Figure 11  
Figure 12  
3. When the bottom wall plate is properly  
installed to the wall.  
4. Lay the carton template on top of the wall  
plate.  
5. Lay the top wall plate on top of the  
cardboard template and mark the four (4)  
mounting points (Figure 12).  
1. Level and secure the plate to the wall  
with the reference arrow facing up to the  
ceiling (Figure 11).  
2. Secure the plate using the provided lag  
bolts and washers.  
Securing the Upper Wall Plate  
Power Source  
Area  
Wall  
Marks  
Wall  
Plates  
Wall Plates  
Figure 14  
Figure 13  
2. Level and secure the plate to the wall with  
the reference arrow facing up to the ceiling.  
3. Secure the plate using the provided lag  
bolts (Figure 14).  
1. Drill four (4) ¼" pilot holes in the  
marked wall (Figure 13). These pilot holes  
will be for the upper mounting bracket.  
CAUTION: Do not over tighten the  
mounting hardware.  
NOTE: CHECK THE MOUNT FOR PROPER  
TIGHTNESS AND SECURITY.  
Page 8  
Installation Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Mounting the Display  
WARNING: AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR  
INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN  
SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL.  
Top  
Bottom  
Figure 15  
1. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top and bottom  
hooks from each bracket to the rods from the wall plates (Figure 15).  
Lateral Shift  
M6 x 30 Lateral  
Shift Screw  
M6 x 30 Lateral  
Shift Screw  
Figure 16  
2. Make any lateral shift adjustments and lock the display in place by tightening the two (2) M6 x 30 (mm)  
Phillips screws found on the bottom of the mounting brackets (Figure 16).  
CAUTION: Do not over tighten the M6 screws to the rods.  
Installation Instructions  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Securing the Display  
M6 x 12mm  
Safety Knob  
M6 x 12mm  
Safety Knob  
Figure 17  
1. Tilt the flat panel and secure the two (2) M6 x 12 mm safety knobs to each of the mounting  
brackets (Figure 17).  
NOTE: To remove the display from the wall simply extend the display to its maximum tilt range,  
remove the two (2) M6 x 12mm Safety Knobs, push the flat panel back to it's flat position and  
loosen or remove the two (2) M6 x 30 lateral shift screws and lift the unit of the wall.  
Page 10  
Installation Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-T210  
Technical Specifications  
Dimensions shown in (mm)/inches.  
Warranty  
Limited Lifetime Warranty  
All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and  
workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts,  
adapters, display equipment or personal injury.  
Contact Premier Mounts  
In the event of missing and/or damaged equipment, or technical questions, the following information can help  
in the completion of the installation.  
Customer Service - (800) 368-9700 Ext. 224  
Technical Support - [email protected]  
Premier Mounts  
3130 E. Miraloma Ave.  
Anaheim CA 92806  
Phone number: 800-368-9700 Fax: 800832-4888  
Installation Instructions  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Guitar G 90 User Manual
Philips Car Satellite TV System 40PFL4709 User Manual
Philips CD Player SAC2530W User Manual
Philips DVD Recorder DVDR3575H User Manual
Philips DVR VR 708A 07 User Manual
Philips MP3 Player A3025 User Manual
Philips VCR VR 720 User Manual
Pico Macom Stereo Receiver PFAM550 User Manual
Pioneer Car Video System DVH P4390UB User Manual
Planet Technology Security Camera CAM IVP52 User Manual