14V/18V SATELLITE
MULTI-SWITCH
TSMS-2150X-16A
Installation
And
Operation
Manual
OM2275N-1 REV. C
10/20/00
P/N: 911051
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
S A F E G U A R D S
Important Information
10. Grounding - This video product is equipped with a two prong
EXAMPLE OF ANTENNA GROUNDING ACCORDING TO
NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED
IN ARTICLE 810 - "RADIO AND TELEVISION
EQUIPMENT"
wall adapter. The shield of the power cord is ground.
11. Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your
appliance dealer or local power company.
POWER LINES
GROUND CLAMP
SERVICE ENTRANCE
CONDUCTORS
12. Power Cord Protection - Power supply cords should be routed
so they are not likely to be walked on or pinched by items placed upon
or against them. Pay particular attention to cords and plugs, conve-
nience receptacles, and the point where they exit from the appliance.
STANDOFF
INSULATORS
b
MAST
SERVICE
ENTRANCE
EQUIPMENT
ANTENNA
LEAD-IN WIRE
13. Lightning - For added protection for this product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet.
ANTENNA
DISCHARGE UNIT
c
G
ROUND CLAM
PS
TO EXTERNAL ANTENNA
TERMINALS OF PRODUCT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(e.g. interior metal water pipe)
14. Power Lines - An outside antenna system should not be located
in the vicinity of overhead power lines, other electric light or power
circuits, where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them
may be fatal.
GROUND WIRE
d
BONDING JUMPER
GROUND CLAMPS
OPTIONAL ANTENNA GROUNDING ELECTRODE
DRIVEN
8
FEET (2.44M) INTO THE EARTH
IF REQUIRED BY LOCAL CODES. SEE NEC
SECTION 810 - 21(f).
20. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to deter-
mine that the product is in proper operating conditions.
15. Overloading - Do not overload wall outlets and extension cords
as this can result in risk of fire or electric shock.
21. Outdoor Antenna Grounding - Before attempting to install this
product, be sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-up static
charges.
16. Object and Liquid Entry - Never push objects of any kind into
this product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
a. Use No.10 AWG (5.3mm ) copper, No.8 AWG (8.4mm (aluminum,
No.7 AWG (10mm ) copper-clad steel or bronze wire or larger, as
ground wire.
17. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
b. Secure antenna lead-in and ground wires to house with stand-off
insulators spaced from 4 feet (1.22m) to 6 feet (1.83m) apart.
c. Mount antenna discharge unit as close as possible to where lead-in
enters house.
18. Damage Requiring Service - Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
d. A driven rod may be used as the grounding electrode where other
typesofelectrodesystemsdonotexist. RefertotheNationalElectrical
Code, ANSI/NFPA 70-1984 for information.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
e. Use jumper wire not smaller than No.6 AWG (13.3mm ) copper or
equivalent, when a separate antenna grounding electrode is used.
d. Iftheproductdoesnotoperatenormallybyfollowingtheoperating
instruction. Adjust only those controls that are covered by the
operatinginstructions. Animproperadjustmentmayresultindamage
and will often require extensive work by a qualified technician to
restore the product to its normal operation.
NOTE TO THE CATV SYSTEM INSTALLER:
THISREMINDERISPROVIDEDTOCALL THECATV
SYSTEM INSTALLER’S ATTENTION TO ARTICLE
820 - 22 OF THE NEC THAT PROVIDES GUIDELINES
FOR PROPER GROUNDING AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE
CONNECTED TO THE GROUNDING SYSTEM OF
THEBUILDING,ASCLOSETOTHEPOINTOFCABLE
ENTRY AS PRACTICAL.
e. If the product has been dropped or the cabinet has been damaged.
f. When the product exhibits a distinct change in performance - this
indicates a need for service.
19. Replacement Parts - When replacement parts are required, be
suretheservicetechnicianhasusedreplacementpartsspecifiedbythe
manufacturer or have the same characteristics as the original parts.
Unauthorized substitutes may result in fire, electric shock or other
hazards.
2
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
and Specifications
TSMS-2150X-16A
14V/18V Satellite Multi-Switch
TSMS-2150X-16A MULTI SWITCH
Features
Provides RHCP and LHCP switching for 16
Input selected by 14V/18V from satellite
receivers
receiver employing right and left hand
circular polarization
Power adapter supplies power to
LNB's
Ideal for smaller systems
Description
The TSMS-2150X-16A is a 14V/18V sat- TSMS-2150X-16Aroutesany of theinputs
ellite multi-switch used in all applications to any of the outputs by utilizing the 14V/
that require satellite I.F. distribution from 18V switching control from the satellite
950 - 2150 MHz. It will allow the user to receivers. The TSMS-2150X-16A pro-
take two LNB outputs and provide inputs vides an excellent way to simplify any
to a maximum of sixteen receivers. The SMATV installation.
Specifications
LNB Output Frequency: 950-2150 MHz
Switching Voltage:
13/14 Vdc
Insertion Loss:
RHCP
LHCP
17/18 Vdc
950 -1750 MHz
1750 - 2050 MHz
2050 - 2150 MHz
-8 dB typical
Power - Wall Adaptor:
117 Vac, 60Hz
"F" type
-13 dB typical
-16 dB typical
Connectors:
Dimensions:
19"L x 2.87"D x 1.75"H
Isolation:
RHCP to LHCP
Output to Output
-35 dB typical
-12 dB typical
(Specifications subject to change without notice)
3
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Hook-up
DSS DISH
AND LNB
LNB RHCP
(13/148V)
24VDC
600mA
OUT
1
OUT
2
OUT
3
OUT
4
OUT
5
OUT
6
OUT
7
OUT
8
OUT
1
OUT
2
OUT
3
OUT
4
OUT
5
OUT
6
OUT
7
OUT
8
LNB LHCP
(17/18V)
SAT
SAT
SAT
SAT
SAT
SAT
SAT
SAT
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
SAT
SAT
SAT
SAT
SAT
SAT
SAT
SAT
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
RECEIVER
1. Connect the RHCP LNB output and the LHCP LNB output to the RHCP(13/14V) and LHCP(17/18V)
inputs respectively of the TSMS-2150X-16A.
2. Connect an output port from the TSMS-2150X-16At to the input of a DSS receiver.
3. Plug the wall adaptor 3.5mm plug into the jack located in the back of the unit. Plug the adaptor into a
120Vac, 60Hz wall receptacle.
4. Each of the satellite receivers can select programs in either right or left hand circular polarities.
To select a right hand circular polarity, a 13/14 DC voltage is used and to select a left
hand circular polarity, a 17/18 DC voltage is used.
4
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
W A R R A N T Y
FIVE YEAR LIMITED WARRANTY
icoMacom,Inc.war- a Return Authorization (RA) number
rants to the original which will be used to track your product.
purchaser this prod- Be prepared to provide:
uct shall be free of 1. The model number and channel
defects in material number of the product
P
and craftsmanship 2. The date of purchase
withonlythelimitationsorexclusions 3. A specific identification of the
set out below. problem
During the warranty period Pico Deliver the products to Pico Macom,
Macom, Inc. or an authorized Pico Inc. or ship the products in the original
Macom service facility will provide, packing material at the address at the
free of charge, the parts and labor bottom of the page. Include satisfactory
necessary to correct defects in mate- evidence of the date of purchase.
rial and workmanship.
Products will not be accepted by Pico
Macom, Inc. without the RA number
clearly indicated on the shipping label.
The foregoing constitutes the Pico
Warranty Duration
This warranty shall terminate five
years from the original date of pur- Macom, Inc. entire obligation with re-
chase of the product or at a time the spect to this product and the original
product is:
purchaser and any user or owner shall
have no other remedy and no claim for
incidental or consequential damages.
Some states do not allow limitations on
how long an implied warranty lasts or
do not allow the exclusions or limita-
tionofincidentalorconsequentialdam-
ages, so the above limitation and exclu-
sion may or may not apply to you.
1. Misused or damaged due to
neglect or improper installation
2. Modified
3. Repaired by someone other
than the warrantor
4. Sold by the original purchaser
Statement of Remedy
To obtain such a warranty service,
This warranty gives you specific le-
contactthesalespersonwheretheprod- galrights,andyoualsohaverightswhich
uct was obtained. You will be issued vary from state to state.
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
PICO MACOM, INC. 12500 Foothill Boulevard, Lakeview Terrace, CA 91342 • (818) 897-0028 • (800) 421-6511 • FAX (818) 834-7197
Download from Www.Somanuals.com. All Manuals Search And Download.
|