POSIFLEX Business Machines Computer Monitor LM 8115 User Manual

LM-8115 / TM-8115 / TM-8315  
LCD Touch Monitor  
User’s Manual  
Rev. B0  
I. FEATURES  
LM/TM-8115 is a stand along LCD monitor for industrial and commercial use.  
TM-8315 is a second display which suit for Posiflex POS Terminals with Gen.5  
base stand.  
Application covers POS, Factory Automation etc.  
High quality 15” TFT LCD panel with scaling function for full screen display.  
TM-8315 support power supply through LCD cable from Posiflex Terminals  
(Power supply need to setup from terminal and please refer to the terminal’s  
manual).  
Recommended LCD resolution: 1024 x 768  
Resistive type extra long life touch panel in USB interface or RS232 interface  
(option) supports touch panel function including left/right button, double click, drag  
& drop  
Touch beep can be pitch adjusted/enabled/disabled by software control (for TM-  
8115/TM-8315)  
USB HUB function with 2 ports for optional side mount devices (SD-400Z or KP-  
300)  
Connect to host through VGA port plus USB port (for all models) and/or COM port  
(for RS232 touch model only)  
Support 2 downlink USB ports  
FCC NOTICE  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the  
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class  
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against  
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause  
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.  
WARRANTY LIMITS  
Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user  
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of  
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.  
ABOUT THIS MANUAL  
This manual assists the user to utilize the LCD Monitor LM-8115 series and the Touch Monitor TM-8115/TM-8315 series. This  
product provides exquisite touch control capability over a stable and adjustable LCD monitor with minimal footprint.  
The manufacturer of the LM-8115 / TM-8115 / TM-8315 touch monitor heartily apologizes to the user for reserving the right to  
change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology.  
Copyright Posiflex Technology, Inc. 2011  
TRADE MARKS AND SERVICE MARKS  
POSIFLEX is a registered trademark of Posiflex Technology, Inc.  
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.  
P/N: 19690903030  
Part 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TM-8315  
After open the carton, please take out the monitor carefully. Please place the  
monitor’s bracket to the back of base stand and fasten the screws which circled  
on the upper picture.  
IV. PARTS IDENTIFICATION  
A. FRONT VIEW  
TM/LM-8115  
Main Unit  
Display Screen  
+ Touch Panel  
Logo + Power  
Indicator  
Adjustable Base  
Assembly  
Option  
SD-400Z  
TM-8315  
Main Unit  
Display Screen  
+ Touch Panel  
Logo + Power  
Indicator  
Adjustable Base  
Assembly  
Option SD-400Z  
Part 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. SIDE VIEWS  
TM/LM-8115  
Lock/release button to  
detach the main unit  
Control button area  
Push in this direction  
to adjust the tilt angle  
of the display panel  
Lock/release lever  
OSD button  
NXT button  
“+” button  
“-“ button  
Power switch  
TM-8315  
Control button area  
Bracket to fix on the  
base stand  
OSD button  
NXT button  
“+” button  
“-“ button  
Power switch  
Part 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
V. INPUT / OUTPUT PORTS  
USB (A)  
(to Devices)  
USB (B)  
(to Host)  
VGA  
input  
COM  
(option RS232)  
12 V DC  
input  
VI. AVAILABLE OPTION ITEMS  
1. Side mount upgrade kit SD-400Z or KP-300  
2. Wall mount kit (WB-6000V-B)  
VII.HARDWARE INSTALLATION  
A.  
Option Side Mount Upgrade Kit  
When a side-mount upgrade kit option such as SD-400Z is  
ordered with the LM-8115 / TM-8115 / TM-8315 monitor, this  
option is already installed in the delivery. No matter the kit  
itself contains MSR only, finger print sensor only or both  
options, the connection to the LM-8115 / TM-8115 / TM-8315  
monitor is through an internal cable in right side cover of the  
LCD/touch unit. Remove the 2 circled screws in the right  
picture to remove the cover for side mount upgrade kit as viewed from back of  
the panel.  
Take out the cable inside this cover as arrowed in the right  
picture here and connect it to connector inside the side  
mount upgrade kit as circled in the same picture. Gently  
arrange the excessive length of this cable back in the hole  
and screw-fit it back to the position originally occupied by  
the cover. Please reserve the cover if there is chance to  
have the side mount kit removed in the future.  
B.  
Cable Connections For TM/LM-8115  
In order to settle the touch monitor properly in a point of sale system, all the  
cable connections have to be routed through its base. Therefore, please observe  
the procedures from A to C below to separate the main unit from the base  
stand assembly after all cables in connection area disconnected.  
Part 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Step A: Prepare a soft clean flat surface, such  
as a piece of cloth on the desk to seat  
the front surface of main unit.  
A
B
C
Step B: Press the Lock/Release button for  
main unit detach and meantime ...  
Step C: Slide the base stand assembly to separate  
the main unit from base stand  
Refer to the bottom view picture of the separated  
base, pass all cable through the cable tunnel as  
hollow arrowed with cable tie from the cable  
passage to the main unit in left picture.  
Cable Passage  
Hook the main unit back onto base stand assembly by matching the matching  
pegs to round part of matching holes and slide them down to slot part till the  
rear lock/release button clicks.  
Matching Pegs  
Matching Holes  
Round Part  
Slot Part  
Connect the VGA cable, USB cable (type B connector) and power cable to the  
I/O connection area of LM-8115 / TM-8115. Connect up to 2 USB devices to  
LM-8115 / TM-8115 at the type A connectors. Please note that unlike usual  
USB HUB, these USB devices won’t be recognized by the host when LM-  
8115 / TM-8115 are powered off.  
Part 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C.  
Option Wall Mount Kit For TM/LM-8115  
Select a flat surface on wall of adequate strength and with proper ventilation  
and space condition. Please use the right material to hold this monitor  
according to the wall material (Drywall,  
concrete, solid wood, etc). Consult with  
your contractor if it is necessary. Please fix  
WB-6000V-B at the holes inside the guide  
holes circled in the picture to the wall or  
fix it to a VESA joint at bosses on back  
side.  
Front Side  
WB-6000V-B  
Back side  
WB-6000V-B  
VIII. DRIVER INSTALLATION  
A.  
INSTALLATION  
The USB interface touch controller operates as an USB mouse without need  
for any special driver in Windows. However, there is a program supported for  
its calibration and touch function manipulation. Please find it in the attached  
Posiflex  
product  
information  
CD-ROM  
under  
subdirectory  
\Drivers\TM_LM\USB or select “Peripheral Drivers & Utilities” then “USB  
Touch Manager” of “TM series” depending on the version of the CD-ROM.  
For Linux environment, please find the setup program for the suitable kernel in  
the same directory and install the required driver and calibration program as  
the setup program proceeds.  
B.  
MOUSE EMULATION  
The touch panel in TM system uses USB interface as standard and the optional  
RS232 interface touch panel model uses RS232 interface. When the touch  
driver is properly installed, this touch panel works exactly like a standard  
mouse for both interfaces. However, if the system is running under safe mode,  
most drivers are disabled in this mode and the touch panel calibration is  
therefore not guaranteed. It is recommended to use a standard USB mouse or  
keyboard in this mode.  
All the below mentioned mouse emulation functions can be manipulated  
through relevant software. The system can give a beep and a click on the left  
button of a mouse at the point when the touch panel is touched. If the point  
touched is dragged across the screen surface, it works as the mouse drag and  
drop feature. If the point is touched, released and touched within a short time  
interval, it is double-clicking left button of the mouse. To obtain the effect like  
Part 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
clicking on the right button of a mouse, touching any point on the screen  
surface after touching the right-click sticky button results as a click on the right  
button of the mouse at that point.  
C.  
a.  
POSIFLEX USB TOUCH MANAGER  
USB touch manager  
Once the USB control program is installed, the user can utilize it to calibrate  
the touch screen, define mouse button emulation parameters, enable right  
button emulation or define the click sound’s tone and duration. Please go to  
“Program Files” and select “Posiflex USB Touch Tools” and then select  
“Posiflex USB Touch Manager” within the tools to engage this utility. Most  
items in this utility should be easily understandable to average user.  
Followings are just some reminders on some items.  
Calibrate – This button engages the “Posiflex USB Touch  
Calibrator”.  
Hide Cursor – This button hides or shows the mouse cursor on  
screen display. Please never hide cursor before the touch is enabled  
and calibrated.  
Restore Defaults – This button resets all touch parameters to default  
settings.  
Edge Accel. – This function engages the “Posiflex USB Touch Edge  
Acceleration Tool” and helps to find the hidden taskbar or thin scroll  
bar through touch.  
Enable Touch – This check box must be checked to have the touch  
panel working.  
Enable Touch_to_Calibrate – This check box provides a shortcut  
for touch calibrator by holding touch for a programmed time delay.  
However, this function denies the touch mode of “Click on Release”.  
Enable Buzzer – This check box enables the internal buzzer beep as  
response to touch on touch panel.  
Enable Frequency – This selection box selects the buzzer tone by  
up/down arrows beside the box.  
Enable Duration – This selection box selects the length for the touch  
beep by up/down arrows beside the box.  
Double Click Area – This selection box selects the size of touch  
point on touch panel by up/down arrows beside the box. A too small  
touch size makes the double click operation difficult. A too large  
touch size results in unsatisfactory touch accuracy.  
Time delay to Touch_to_Calibrate – This selection box defines the  
touch time required for a shortcut to Touch Calibrator by up/down  
arrows beside the box when the “Enable Touch_to_Calibrate” check  
Part 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
box is checked.  
Touch Mode Setting – Only one of the three radio buttons can be  
selected. The mouse emulation refers to the drag and drop function.  
OK – This button accepts all parameters set and closes the utility  
window.  
Apply – This button accepts all parameters set and remains in the  
utility window.  
Cancel – This button discards all changes to the parameters and  
closes the utility window.  
Help – This button provides explanations.  
b.  
USB touch calibrator  
This program helps re-calibrating the touch position with the USB mouse  
emulation. Please touch the calibration targets at each corner and a  
confirmation box that appear sequentially.  
c. USB touch edge acceleration tool  
Helps to find the hidden taskbar or thin scroll bar through touch  
Enable ... – Each check box determines whether or not to engage  
edge acceleration against which edge of screen.  
Margin – This list button selects the range to engage edge  
acceleration toward the edge before the edge is reached.  
Compensation – This list button selects the distance to advance the  
mouse toward edge from touch point.  
d.  
USB touch right button tool  
This tool differs slightly from the “Touch as Right Button Click” check box in  
the USB touch manager. When executed, there will be a small window of  
“One Shot Right Button” appearing on desktop. Any touch on the panel right  
after touching this small window will work like clicking the right button of  
mouse at that point. However, the next touch will resume the left button of  
mouse unless the small window is touched again.  
D.  
RS232 TOUCH CONTROLLER  
If the TM-8115/TM-8315 system purchased is the RS232 interface Resistive  
type touch panel, the touch controller is of RS232 interface. The “Posiflex  
Touch Terminal Manager” above should be disregarded. In case there is any  
external COM port summoned for this purpose, that COM position of the  
system will be covered in the connection area. Removal of this cover will  
void the product warranty!!  
Once the RS232 touch controller driver is installed, the user can utilize it to  
control the mouse emulation. Please click “Start”, “Settings” “Control Panel”  
and “Elo Touchscreen” or just click the “elo” icon in tool tray to engage this  
utility. However, with this touch controller driver, certain display mode like  
Part 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
full screen display of Windows DOS box should be avoided.  
E.  
APPLICATION LIMITATION  
The USB touch is not applicable for OS other than Windows as USB mouse is  
not supported in DOS environment. The USB touch is also not applicable  
when the monitor is used to be the extended screen in multiple monitor  
application.  
In using the MSR of the side mounted upgrade option for reading a magnetic  
stripe card, be sure to insert the card to the bottom with magnetic stripe facing  
the mark aside the slot. The movement of the card can be either inserting the  
card from the top surface then sliding the card down out of the slot, or sliding  
the card upward from the lower side of the slot till it reaches the top end as  
long as the card is a standard one. A non-standard card recorded without  
complete degaussing prior to recovery may accept only one direction in card  
reading.  
If the fingerprint sensor option is installed in the side mount kit, please find the  
most comfortable angle for the fingerprint taking operation in consideration of  
the LCD panel tilt angle and try to align the core of fingerprint in the sensing  
area.  
IX. LED MODULE INDICATION  
Green: standby  
Blue: power on  
When this touch monitor is turned ON, the LED light is in blue. When the  
VGA signal vanishes, the monitor shows “No signal” for a while and goes into  
standby mode and LED is green. However, the touch panel is still operational.  
X. OSD (ON SCREEN DISPLAY) SCREEN ADJUST FUNCTION  
A.  
OSD buttons  
The 4 OSD control buttons are above the power  
switch button on left side of the LCD panel.  
“OSD” button: To enter OSD setup menu, or to  
perform function selected in OSD operation.  
“NXT” button: To go to next option function.  
” “” button: To increase setting value.  
” “” button: To decrease setting value.  
Part 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B.  
OSD functions  
Press “OSD” button with a normal display on the screen to activate the OSD  
functions (On Screen Display adjustment). The OSD window will pop up on  
the screen. On top part of this window is a Posiflex logo with the OSD  
firmware version indicated to its lower right. Below this area is a row of icons  
for main OSD menu. Below the main menu is a group of icons for submenu  
that corresponds to one icon selected in the main menu. An analysis of the  
video signal on resolution and refresh rate will be displayed at the bottom.  
Applicable icons in the main menu and its subsequent menus are explained  
below.  
MAIN MENU”: There are in total 5 icons in this  
menu: One of the 5 icons will be displayed in inverted color to indicate its  
relationship with the submenu below. Pressing “NXT” button will shift the  
selected icon one by one from left to right and then wrap around to the most  
left. Press “OSD” button to enter the selected sub menu. If there is no button  
for OSD setting is pressed within a period of time (about 5 seconds to 1 minute  
as programmed) the OSD window will disappear with all the adjusted  
parameters saved. Explanations on items in sub menu are as below.  
“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3  
icons in this submenu:  
Press “OSD” button to select item or return  
to main menu. Press “NXT” button to select among brightness, contrast and  
exit.  
“BRIGHTNESS ADJUST”: When this item is selected, there  
will be only the brightness icon with an adjustment indication bar under  
it between the main menu area and the video signal mode. Press “+”  
button to increase brightness. Press “-” to decrease. Press “OSD” button  
to save the current setting and return to “Brightness/Contrast submenu”.  
“CONTRAST ADJUST”: When this item is selected, there will  
be only the contrast icon with an adjustment indication bar under it  
between the main menu area and the video signal mode. Press “+”  
button to increase contrast. Press “-” to decrease. Press “OSD” button  
to save the current setting and return to “Brightness/Contrast submenu”.  
“EXIT”: Return to “Main menu”.  
“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:  
Press “OSD” button to select item or return to main menu.  
Press “NXT” button to select among auto color adjust, auto  
RGB reset, Color balance adjust and exit.  
“AUTO COLOR ADJUST”: Upon an “OSD” button press on  
this icon the monitor will perform an automatic color adjustment and  
Part 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
exits the OSD window leaving 2 icons below at center of the screen.  
Press “NXT” button to switch the selection. Press “OSD” button to  
make the choice.  
“ACCEPT”: Accept the adjustment setting.  
“REJECT”: Decline the adjustment setting and return to  
previous setting.  
“AUTO RGB RESET”: Upon an “OSD” button press on this  
icon the monitor will perform an automatic RGB reset and exits the  
OSD window leaving 2 icons below at center of the screen. Press  
“NXT” button to switch the selection. Press “OSD” button to make the  
choice.  
“ACCEPT”: Accept the reset result.  
“REJECT”: Decline the reset and return to previous setting.  
“COLOR BALANCE ADJUST”: When this item is selected,  
there will be 7 icons in this item:  
between main  
menu area and the video signal mode. Press “OSD” button to select an  
item or return to color adjust submenu. Press “NXT” button to select  
among separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K and  
exit.  
“SEPARATE COLOR ADJUST”: When this item is  
selected, there will be 3 adjustment indication bars between the  
main menu area and the video signal mode. Press “NXT” button to  
select among the 3 colors Red, Green and Blue respectively. Press  
“+” button to intensify that color. Press “-” to reduce. Press  
“OSD” button to save the current setting and return to “Color  
balance adjust submenu”.  
“4200K”: Pressing “OSD” button on this icon will set the  
color balance to a color temperature of 4200 degrees Kelvin.  
“5000K”: Pressing “OSD” button on this icon will set the  
color balance to a color temperature of 5000 degrees Kelvin.  
“6500K”: Pressing “OSD” button on this icon will set the  
color balance to a color temperature of 6500 degrees Kelvin.  
“7500K”: Pressing “OSD” button on this icon will set the  
color balance to a color temperature of 7500 degrees Kelvin.  
“9300K”: Pressing “OSD” button on this icon will set the  
color balance to a color temperature of 9300 degrees Kelvin.  
“EXIT”: Return to “Color adjust submenu”.  
“EXIT”: Return to “Main menu”.  
“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this  
submenu: Press “OSD” button to select item or return  
to main menu. Press “NXT” button to select among auto geometry adjust,  
Part 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
horizontal size, phase, horizontal position, vertical position and exit.  
“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press  
on this icon the monitor will perform an automatic geometry adjustment  
and exits the OSD window leaving 2 icons below at center of the screen.  
Press “NXT” button to switch the selection. Press “OSD” button to  
make the choice.  
“ACCEPT”: Accept the adjustment setting.  
“REJECT”: Decline the adjustment setting and return to  
previous setting.  
“HORIZONTAL SIZE”: When this item is selected, there will  
be only the horizontal size icon with an adjustment indication bar under  
it between the main menu area and the video signal mode. Press “+”  
button to increase horizontal size. Press “-” to decrease. Press “OSD”  
button to save the current setting and return to “Geometry adjust  
submenu”.  
“PHASE”: When this item is selected, there will be only the  
phase adjust icon with an adjustment indication bar under it between  
the main menu area and the video signal mode. Press “+” or “-” button  
to adjust the pixel synchronization phase for best picture display. Press  
“OSD” button to save the current setting and return to “Geometry  
adjust submenu”.  
“HORIZONTAL POSITION”: When this item is selected, there  
will be only the horizontal position icon with an adjustment indication  
bar under it between the main menu area and the video signal mode.  
Press “+” or “-” button to shift the screen display to right or left. Press  
“OSD” button to save the current setting and return to “Geometry  
adjust submenu”.  
“VERTICAL POSITION”: When this item is selected, there  
will be only the vertical position icon with an adjustment indication bar  
under it between the main menu area and the video signal mode. Press  
“+” button to shift up the screen display. Press “-” to shift down. Press  
“OSD” button to save the current setting and return to “Geometry  
adjust submenu”.  
“EXIT”: Return to “Main menu”.  
“TOOLS SUBMENU”: When this item is selected, there are 5 icons  
in this submenu:  
Press “OSD” button to select item or  
return to main menu. Press “NXT” button to select among OSD submenu,  
reset to default, phase, smoothness / sharpness adjust, mode select and exit.  
“OSD SUBMENU”: When this item is selected, there are 4 icons  
in this submenu:  
Press “OSD” button to select item  
or return to main menu. Press “NXT” button to select among OSD time,  
Part 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD horizontal position, OSD vertical position and exit.  
“OSD TIME”: When this item is selected, there will be  
only the OSD time icon with an adjustment indication bar under  
it between the main menu area and the video signal mode. Press  
“+” or “-” button to adjust the waiting time for OSD operation  
before OSD termination between 5 to 60 seconds. Default is 30  
seconds. Press “OSD” button to save the current setting and  
return to “OSD submenu”.  
“OSD HORIZONTAL POSITION”: When this item is  
selected, there will be only the vertical position icon with an  
adjustment indication bar under it between the main menu area  
and the video signal mode. Press “+” button to shift OSD  
window right. Press “-” to shift left. Press “OSD” button to save  
the current setting and return to “OSD submenu”.  
“OSD VERTICAL POSITION”: When this item is  
selected, there will be only the vertical position icon with an  
adjustment indication bar under it between the main menu area  
and the video signal mode. Press “+” button to move OSD  
window downward. Press “-” to go upward. Press “OSD” button  
to save the current setting and return to “OSD submenu”.  
“EXIT”: Return to “Tools submenu”.  
“RESET TO DEFAULT”: Pressing “OSD” button on this icon  
will set all parameters back to the status when the monitor left factory.  
“SMOOTHNESS / SHARPNESS ADJUST”: When this item is  
selected, there will be only the smoothness / sharpness adjust icon with  
an adjustment indication bar under it between the main menu area and  
the video signal mode. Press “+” button to increase smoothness of  
display (decrease sharpness). Press “-” to go the other way. Press  
“OSD” button to save the current setting and return to “OSD submenu”.  
“MODE SELECT”: Pressing “OSD” button on this icon will  
have no effect at all if the display mode is not one of the confusing  
modes. The confusing modes here mean 640 x 400 or 720 x 400 in  
display resolution as both mode have refresh rate of 70Hz, horizontal  
frequency of 37.9KHz and pixel frequency of 31.5MHz making it  
impossible for automatic select. These modes are not used in normal  
Windows display.  
“EXIT”: Return to “Main menu”.  
“EXIT”: Exit OSD setup with all adjustment saved.  
Part 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
XI. SUPPORTED DISPLAY MODES  
For video signals beyond the supported display modes, there will be a message  
“Out Of Range” on middle of screen. Maximum supported color depth is 24  
bits or 16.2 M colors. Supported display modes are as in the table:  
Horizontal Frequency  
Display Resolution  
Refresh Rate (Hz)  
(KHz)  
31.5  
31.5  
37.9  
37.5  
31.5  
35.1  
37.9  
48.1  
46.9  
48.4  
56.5  
60  
640*400  
70  
60  
72  
75  
70  
56  
60  
72  
75  
60  
70  
75  
640*480  
720*400  
800*600  
1024*768  
XII.TROUBLE SHOOTING  
In case of any malfunction, please check the following points in sequence to  
resolve it.  
1. If there is no power indication, please check the power connection.  
2. If there is no picture display with power LED on, please check the video  
signal connection.  
3. If there is no touch function, please check the connection of the USB  
cable for USB interface touch controller.  
T31454  
Part 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Paxar Printer Monarch 9416 User Manual
Peg Perego Riding Toy IGED1068 User Manual
Philips Digital Photo Frame SPF3410 G7 User Manual
Philips DVD Player DVD722 051 User Manual
Philips DVD Player DVD 955 User Manual
Philips Home Theater System MCD107 98 User Manual
Philips Portable Generator PW 1720 User Manual
Philips Projector cSmart Series User Manual
Philips Speaker MMS460 User Manual
Prima Washer LPR 712 User Manual