&
OPERATING INSTRUCTIONS IN BRIEF
The remote control
Front of the video recorder
RECORD/OTR n
STANDBY m
SELECT
TIMER k
CLEAR (CL)
0-9
STANDBY m
Record
Standby
r
Standby
Down/Minus, programme number
q
RECORD 5
AUTOINSTALL
hSTOP/JEJECT
H
Function selector
Up/Plus, programme number
Record
’VIDEOPlus’ or ’TIMER’ programming
Reset, clear
Installation
Digit buttons 0-9
Stop/Cassette eject
Rewind/Reverse scanning
Playback
MONITOR
OK
TV monitor function
Confirm button
PLAY G
P r
I
Down/Minus, programme number
Up/Plus, programme number
Playback
Forward wind/ Forward scanning
P q
PLAY G
H
Rewind/Reverse scanning
Forward wind/ Forward scanning
Pause/Stop, Tuner-mode
Index search
I
STOP h
INDEX E
SP/LP
(SP/LP) selection
STILL R
SYSTEM
Still picture
Special function
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS PHILIPS VR 175
Congratulations on the purchase of one of the most sophisti-
cated and simple-to-use video recorders (VCR) on the market.
With this VCR you can record and play VHS-standard
Contents
Page
1. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connecting cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important notes for operation . . . . . . . . . . . . . . . . . . . . 2
Connecting additional equipment . . . . . . . . . . . . . . . . . . 3
Emergency interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
User guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Automatic Channel Search . . . . . . . . . . . . . . . . . . . . . . . 4
Manual Channel Number Allocation . . . . . . . . . . . . . . . 4
Monitor function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
cassettes.
Please take the time to read this operating manual before
using your video recorder.
2. PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Picture scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
INSTANT VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Still picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tape position/Index search . . . . . . . . . . . . . . . . . . . . . . 5
Eliminating picture interference . . . . . . . . . . . . . . . . . . . 6
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety instructions and other notes
•
Danger: High voltage! Do not open. The video recorder does not
contain any components that can be repaired by the customer.
When the appliance is connected to the power supply there are
some components that are constantly operational. To switch off
the video recorder completely you must disconnect it from the
power supply.
3. RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Long play function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Some general notes for recording . . . . . . . . . . . . . . . . . 7
Recording from external sources . . . . . . . . . . . . . . . . . . 7
OTR - Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Erase protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Auto-assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming with ’VIDEOPlus+’ . . . . . . . . . . . . . . . . . . 8
Programming recordings manually . . . . . . . . . . . . . . . . 8
Clear a TIMER block . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Important programming notes . . . . . . . . . . . . . . . . . . . . 9
•
•
•
Note that this power pack is designed for a power supply of
220-240V/50Hz.
Ensure that air can circulate freely through the ventilation slots
on the video recorder.
Ensure that no objects or liquids enter the video recorder. If
liquid is spilt into it, disconnect the video recorder immediately
from the power supply and call the After-sales Service for
advice.
•
The video recorder should not be used immediately after
transportation from a cold to a hot area or vice versa, or in
conditions of extreme humidity.
After unpacking the video recorder, it should be allowed to
acclimatize for at least three hours before installation.
These operating instructions have been printed on nonpolluting
paper.
Deposit old batteries at the relevant collection points.
Please make use of the facilities available in your country for
disposing of the packaging of the video recorder in a way that
helps to protect the environment.
4. SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tuner mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
On Screen Display (OSD) . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Channel number or frequency display . . . . . . . . . . . . . 10
Manual channel search . . . . . . . . . . . . . . . . . . . . . . . . 11
Playback via the aerial cable . . . . . . . . . . . . . . . . . . . . 12
Adjusting the modulator frequency . . . . . . . . . . . . . . . 12
Switching off the modulator . . . . . . . . . . . . . . . . . . . . . 12
Before you call an engineer . . . . . . . . . . . . . . . . . . . . . 13
•
•
•
•
•
This electronic equipment contains many materials that can be
recycled. Please inquire about the possibilities for recycling
your old set.
VIDEOPlus+ and PlusCode are trademarks of Gemstar Develop-
ment Corporation. The VIDEOPlus+ system is manufactured
under licence from Gemstar Development Corporation.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INSTALLATION
2 Plug one end of the aerial cable provided into the
Important for the United Kingdom
3
socket on the video recorder and the other end
into the aerial input socket on your TV set.
This apparatus is fitted with an approved moulded 13 Amp
plug. To change a fuse in this type of plug proceed as
follows:
3 If your television does not have a scart (AV-Euro) socket
please do not read further here, but turn to Chapter 4,
’SPECIAL FEATURES’. In the section ’Playback via the
aerial cable’ you will find further information.
•
•
Remove fuse cover and fuse.
Fix new fuse which should be a BS1362 3A, A.S.T.A.
or BSI approved type.
•
Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of
3A. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5A.
4 Insert the plug of a scart cable into the scart socket
Note: The severed plug must be destroyed to avoid a
possible shock hazard should it be inserted into a 13A
socket elsewhere.
EXT.1
at the back of your video recorder. Connect the
other plug to the TV set.
How to connect a plug: The wires in the mains lead are
coloured in accordance with the following code:
BLUE - ’NEUTRAL’ (’N’) BROWN - ’LIVE’ (’L’)
The BLUE wire must be connected to the terminal which
is marked with the letter ’N’ or coloured BLACK. The
BROWN wire must be connected to the terminal which is
marked with the letter ’L’ or coloured RED.
Do not connect either wires to the earth terminal in the
plug which is marked with the letter ’E’ or by the safety
earth symbol \ or coloured green or green-and-yellow.
5 Insert the female plug of the mains cable into the mains
4
socket
at the back of the video recorder.
•
•
6 Plug the other end of the mains cable into the wall
socket.
Important notes for operation
•
Many televisions switch automatically to the ’EXT’
(EXTernal) or ’AV’ (Audio/Video) programme number
when a video cassette is played back.
If the television does not switch automatically, you will
have to select the ’EXT’, ’0’, or ’AV’ programme number
on the TV set manually.
Keep your video recorder connected to the mains and the
power switch in ’on’ position at all times to ensure that
programmed recordings can be made and that the
television functions normally. The power consumption
required is low.
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply over
the two wires.
Connecting cables
•
•
•
•
•
The video recorder switches on automatically as soon as
P q
you insert a cassette or press the
button.
If the video recorder is not used for a few minutes in
some functions, it switches to standby automatically.
Back-up power supply: TV channel storage - typically 1
year, Clock/Timer - 30 minutes
If you switch the video recorder to standby using the
STANDBY m
button, the current time will appear in the
display, e.g.: ’20:00’ .
If the clock has not been set, ’--:--’ will appear in the
display.
1 Remove the aerial cable plug from your TV set and insert
2
it into the
socket at the back of the video recorder.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting additional equipment
User guide
You can also connect additional equipment to the
socket, for instance, satellite receiver, decoder or
camcorder.
With OSD (On Screen Display) the corresponding functions
appear on the TV-screen. The most important button-func-
tions are displayed at the bottom of the screen.
EXT.1
DATE PROG START
01 01 20:00
END
21:30
------------------------
NEXT
gTIMER CLEAR gCL
-/+ 0-9 D/WgSELECT OK
Throughout this instruction manual, use the following buttons
for these functions: ’Select’, ’Enter’/’Adjust’, ’Confirm’.
P r
P q
Select: Use the
or the
button.
Note: You can find information about how to connect
your TV set in chapter 4, ’SPECIAL FEATURES’ in the
section ’Playback via the aerial cable’.
P r
P q
Enter/Adjust: Use the
or the
button, or the
0-9
buttons.
OK
Confirm: Use the
button.
Emergency interrupt
Both the video recorder and the remote control have an
’Emergency interrupt’ button. You can use the
STANDBY m
button to interrupt any function.
Whenever you have operating problems you can simply
interrupt the function and start again.
You can practise operating your set without any worries. No
matter which buttons you press, you cannot damage it.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Channel Search
Manual Channel Number Allocation
AUTOINSTALL
1 Switch on the TV set. Press the
button on
You can allocate any desired programme number to the TV
channels stored by the ’Automatic Channel Search’.
the video recorder. If TV channels have already been
stored, select and confirm the ’AUTOINSTALL’ line.
AUTOINSTALL
1 Switch on the TV set. Press the
button on
2 The ’Automatic Channel Search’ starts.
the video recorcer.
2 Select and confirm ’CHANNEL ALLOCATION’ .
P r
P q
3 Use the
or
button, to select the TV channel
AUTOINSTALL
00
on the TV screen, to which you wish to allocate a
programme number (starting with ’P 01’ ).
4 Confirm this allocation.
If you wish to allocate further programme numbers,
repeat step 3and step 4until you allocated a pro-
gramme number to all the required TV channels.
3 Wait until all the TV channels have been found. This may
take several minutes.
STANDBY m
5 To end press the
button.
4 Adjust ’TIME’ , ’YEAR’ , ’MONTH’ , ’DATE’ .
Note: If you want to delete an unwanted TV channel,
OK
5 Confirm each entry with the
button.
CLEAR (CL)
press the
button at step 3.
* Monitor function: You can switch to and fro between
How you can search for a TV channel manually, you read in
chapter 4 ’SPECIAL FEATURES’, ’Manual channel search’.
How you can allocate a TV channel manually, you read in the
next paragraph, ’Manual channel allocation’.
TV reception and video recorder reception with the
MONITOR
button. This only functions when you used a
scart cable to connect the video recorder to your TV set
and if your TV set responds to this switch-over.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. PLAYBACK
1 Insert the cassette into the cassette slot.
Still picture
STILL R
1 Press the
button. You see a still picture.
Interference stripes will appear on the screen.
STILL R
2 Each time you press
again, the picture will
move on one step.
Note: If the still picture vibrates vertically, hold the
P r
P q
or the
button at step 1until the vibration is
minimal. This setting will be stored automatically.
Please note, however, that interference may still occur
with poor quality cassettes.
PLAY G
2 Press the playback button
.
H
3 Picture scanning: Press the
(reverse) or
I
(forward) button once or several times.
Tape position/Index search
STOP h
4 Interrupt: Press the
button.
5 Wind and rewind: Interrupt the playback function and
Tape position: The elapsed playback time, given to the hour
and minute, appears in the display.
H
I
press the
(rewind) or
(wind) button.
If you want to set the indicator to ’0:00’ , press the
CLEAR (CL)
button.
When you insert a cassette, the indicator is automatically
set to ’0:00’ .
0:20
Index search: At the beginning of each recording, the video
recorder marks the tape with a code mark. You can search
for these code marks on the tape. Once the video recorder
finds the code mark or a blank space it will automatically
switch to playback.
If, during wind/rewind, you want to have a quick access
to picture scanning, use the ’Instant View’ function.
H
6 INSTANT VIEW: If you hold the
(Rewind) or
I
(Wind) button during wind or rewind, you will
switch to picture scanning. If you release the buttons,
the video recorder will automatically switch back to
rewind or wind again.
INDEX E
I
1 Press the
button and then press the
H
button to select the next code mark or the
for the previous code mark.
button
7 Eject a cassette: Interrupt the playback function and
Note: You cannot use the function ’Index search’ with
recordings made on another video recorder that does
not have this code mark function.
hSTOP/JEJECT
press the
button on the video recorder.
Notes: Some functions switch off automatically after a
while (e.g.: Pause, Still Picture, Scanning). This helps to
protect the cassette and prevent unnecessary power
consumption.
* The picture quality will deteriorate during Picture
Scanning. The sound is turned off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Eliminating picture interference/
Cleaning function
P q
1 During playback, hold the
button until ’TRAC’
(tracking) appears in the display.
P q
P r
2 Hold the
is at its best.
or
button until the playback quality
3 Wait a few seconds, until ’TRAC’ disappears from the
display. This setting will remain until you remove the
cassette.
4 If horizontal lines still appear on the screen, use the
Cleaning function:
Cleaning function: During playback, hold the
PLAY G
button until ’HEAD’ (video head cleaning)
appears in the display. The video heads are being
cleaned. The video recorder automatically switches back
to playback.
Note: Some hired cassettes may have a poor pic-
ture/sound quality. This is not a fault in your video
recorder.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. RECORDING
1 Insert a cassette or switch the video recorder on with the
Some general notes for recording
P q
button.
P r
P q
0-9
•
Recording from external sources: Programme number
2 Use the
or
button or the
buttons to
’E1’ is provided for recording from external sources (via
select the programme number from which you wish to
record, e.g. ’P 01’ .
EXT.1
the
scart socket).
•
OTR - recording: If you do not want to record to the end
RECORD 5
of the cassette, press the
button again.
The display shows at what time the recording will stop.
P 01
RECORD 5
With each subsequent press of the
you can add 30 minutes to this time.
button
You can return to the normal recording status by pressing
RECORD 5
3 Press the
button.
CLEAR (CL)
the
button.
•
Erase protection: So that you don’t accidentally delete an
important recording, you can remove the special tab
(erase protection) on the narrow side of the cassette with
a screwdriver or slide the special tab to the left.
Later, if you no longer want the cassette to be erase
protected, you can seal the gap again with adhesive tape
or slide the special tab to the right.
0:00
STOP h
4 To stop recording, press the
button.
•
Auto-assembling: You can use the auto-assembling func-
tion to join individual recordings without any major
picture disturbance between the recordings. During
Long play function
You can reduce the recording speed by half. This makes it
possible to record, for example, 8 hours instead of 4 hours on
an ’E240’ cassette.
playback, search for the correct position on the tape and
hSTOP/JEJECT
then press the
button. 9 will appear in
the display. Now you can start recording as usual by
RECORD 5
pressing the
button.
Before recording, with the video recorder switched on, select
the ’LP’ (=LongPlay) recording speed by pressing the
SP/LP
button. ’LP’ will appear in the display.
How to programme a recording
Note: During picture scanning, still picture and slow
motion colour playback may be poor.
* You will obtain the best picture quality when recording
at standard speed (’SP’).
The video recorder needs the following information for every
programmed recording:
* the date on which the recording is to be made
* the programme number for the TV channel
* the start and stop time of the recording
The video recorder stores all the information mentioned
above in what is known as a TIMER block. You can
programme up to 6 TIMER blocks, one month in advance.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Make sure that a cassette without erase protection has
Programming with ’VIDEOPlus+’
STANDBY m
been loaded. Switch to standby with the
button.
All the information required for a programming is contained
encoded in the VIDEOPlus+ code.
A programmed recording will only function when the
video recorder is switched to standby with the
STANDBY m
button.
1 Switch on the TV set.
Note:
TIMER k
* VIDEOPlus+ Aerial-code numbers: With this video
recorder, VIDEOPlus+ aerial-code numbers will be al-
located automatically.
2 Press the
button on the remote control.
3 Please enter the VIDEOPlus+ code (up to 9 digits) printed
in your TV guide next to the start time of a TV pro-
gramme.
CLEAR (CL)
If you make a mistake, clear with the
Programming recordings manually
button.
TIMER k
VIDEOPLUS
53124----
1 Switch on the TV set. Press the
button twice.
TIMER k
2 Select a free TIMER block. Press the
button.
ONCE
TIMER k
3 With the
button you can select between the
------------------------
D/WgSELECT
CLEAR gCL
entries ’DATE’ (date), ’PROG’ (programme number),
’START’ (start time) and ’END’ (stop time).
0-9
OK
You can enter or adjust data. Confirm each entry with the
TIMER k
button.
4 If you want to programme at daily or weekly intervals,
You can select between ’D’ (daily intervals) or ’W’
(weekly intervals) at step ’DATE’ with the
SELECT
press the
button until ’D-DAILY’ (daily intervals)
SELECT
button.
or ’W-WEEKLY’ (weekly intervals) appears on the TV
screen. The ’daily intervals’ function can only be used for
recordings to be made from Mondays to Fridays inclu-
sive.
OK
4 Finally, press the
button. Programming has now
been completed.
OK
5 Make sure that a cassette without erase protection has
5 Confirm the entries with the
button. The resultant
STANDBY m
been loaded. Switch to standby with the
data appear on the TV screen.
button.
Note: If you use VIDEOPlus+ for the first time for this TV
channel, the ’SELECT PROG’ line appears when you
confirm the VIDEOPlus+ code. Select and confirm the
programme number for the TV programme required.
Note:
* Clear a TIMER block: At step 1select the TIMER
block that you want to clear. Press the
button.
If e.g.: ’20:00’ appears in the display, the clock must be
set.
CLEAR (CL)
* If you wish to set a later end time for a recording,
P q
press the
the
button at step 5. With each press on
P q
button you add 15 minutes to the time.
* If e.g.: ’20:00’ appears in the display, please set the
clock.
OK
6 Finally, press the
button. Programming is now
complete.
The data has been stored in a TIMER block.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Important programming notes
•
When recordings have been programmed, k appears in
the display.
•
The programmed recording will always be made at the
recording speed (SP/LP) that at the time has been
selected on the video recorder.
•
You cannot operate the video recorder manually while a
programmed recording is being made. If you want to
interrupt the programmed recording, press the
STANDBY m
button.
•
•
•
•
If the video recorder is switched on a few minutes before
a programmed recording is due to take place,
’TIMER RECORD’ will flash on the TV screen.
If the end of the cassette is reached during a
programmed recording, the video recorder automatically
ejects the cassette.
If you forget to load a cassette, after programming the
recording, ’NO CASSETTE’ will appear on the TV screen
for a few seconds.
If you insert a cassette with erase protection, after
programming the recording, ’PROTECTED CASSETTE’ will
appear on the TV screen for a few seconds.
The cassette will then be ejected.
TIMER k
•
•
When, after pressing the
button ’TIMER FULL’
appears on the TV screen, all TIMER blocks have been
programmed. Then, select the TIMER block you want to
alter or clear.
If ’CODE ERROR’ appears on the TV screen, the
VIDEOPlus+ code was incorrect or the date was in-
correctly entered. Repeat the entry or end with the
STANDBY m
button.
With programming at daily intervals, the first recording
must take place within a week.
•
•
If ’DAILY ERROR’ appears on the TV screen, the date was
incorrectly entered. Programming at daily intervals can
only be used for recordings to be made from Mondays to
Fridays inclusive.
Programme number ’E1’ is provided for programmed
EXT.1
recordings from external sources (via the
socket).
scart
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. SPECIAL FEATURES
Tuner mode
Setting the clock
AUTOINSTALL
You can also use your video recorder as a TV receiver
(tuner).
1 Press the
button on the video recorder.
2 Confirm the line ’CLOCK’ .
STOP h
1 Hold the
button, until + appears in the
display.
3 Adjust ’TIME’ , ’YEAR’ , ’MONTH’ , ’DATE’ if required.
4 Confirm each entry.
2 Choose the required programme number with the
P r
P q
0-9
or
button or with the
buttons.
3 Switch the video recorder to standby by pressing the
Channel number or frequency display
STANDBY m
button when you no longer want to watch
television.
You can switch between the display for ’channel number’ or
’frequency’ for manual channel search.
On Screen Display (OSD)
AUTOINSTALL
1 Press the
button.
You can switch the On Screen Display (OSD) on or off.
2 Select and confirm ’CHANNEL/FREQUENCY’ .
AUTOINSTALL
1 Press the
button on the video recorder.
3 Select and confirm ’CHANNEL’ or ’FREQUENCY’ .
2 Select and confirm ’OSD’ .
3 Select and confirm ’ON’ or ’OFF’ .
OK
Note: With the
button you can superimpose the
actual operating mode on the TV screen.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual channel search
In certain cases the Automatic Channel Search may not be
able to find all of the TV channels (e.g. coded TV channels).
You can then use this manual method to set the channels.
AUTOINSTALL
1 Switch on the TV set. Press the
button on
the video recorder.
2 Select and confirm ’MANUAL SEARCH’ .
P q
3 Hold the
button until you have found the right TV
channel. A changing channel number or frequency will
appear on the TV screen.
OK
4 Confirm with the
button.
5 Select and confirm the programme number that you wish
to allocate to this TV channel (e.g.: ’P 01’ ).
6 If you want to allocate more TV channels, repeat
steps 3to 5until all TV channels have been stored.
STANDBY m
7 To end, press the
button.
Note: Channel number or frequency can also be entered
0-9
directly at step 3, using the
buttons.
* To enter a special/hyperband channel, first enter the
channel digit ’9’. The indication changes from ’CH’ to
’CA’. For example, for special channel ’S 30’, enter ’9 30’.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: This modulator frequency might already be oc-
cupied by another TV station in your reception area, e.g.
’Channel 5’. In this case you will find that the picture
quality on your TV set will be poor when receiving one
or more TV channels.
Playback via the aerial cable
If you do not wish to use a scart cable, the aerial cable
which is already connected will act as the connection
between your TV set and the video recorder. Ensure that the
video recorder is connected to the mains supply.
* Adjusting the modulator frequency: If the picture
quality only deteriorates when the video recorder is
switched on, adjust the modulator frequency. The fre-
P r
quency can be adjusted at step 2with the
or the
1 Switch on your TV set and select the programme number
that you have earmarked for video playback. (see operat-
ing manual for your TV set).
P q
button. Confirm the adjusted frequency with the
button.
OK
* Switching off the modulator: If you cannot eliminate
picture or sound interference using the above method
you can switch off the built-in modulator. You should
only do this if you have connected the video recorder to
the TV set using a scart cable. ’Playback via the aerial
cable’ is not possible when the modulator is switched
2 Ensure that no cassette has been loaded. With the video
SYSTEM
recorder switched to standby, hold the
but-
ton for a few seconds until a modulator frequency e.g.:
’M583’ (UHF-channel 35 ) appears in the display. The
video recorder transmits a test picture.
off.
CLEAR (CL)
At step 2, press the
button for several
3 Tune in the TV set in the UHF wave band until this picture
seconds until ’MOFF’ (modulator switched off) appears
in the display. You can switch back again in the same
way.
appears.
MODULATOR
583
------------------------
-/+
ON/OFF gCL
OK
4 Switch the video recorder to standby with the
STANDBY m
button.
If you have interrupted making standard settings as
described in Chapter 1, ’INSTALLATION’, turn to that
chapter to continue making the standard settings.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the serial number of your appliance here:
Before you call an engineer
If, contrary to expectation, you experience any difficulty in
operating this video recorder, it may be caused by one of the
reasons mentioned below. You can also call the customer
service in your country.
MODEL NO./TYPE
VR 175
PROD.NO.:/SER.NR. . . . . .
You will find the telephone numbers in the enclosed guar-
antee leaflet.
This product complies with the requirements of the Directive
73/23/EEC + 89/336/EEC + 93/68/EEC.
The set does not respond to any button being pressed:
•
•
•
No power supply.
A programmed recording is currently being made.
Technical disturbance: disconnect from the mains for 30
seconds, then re-connect. If this does not have any effect, you
Interference
can: 1. Disconnect from mains. 2. Re-connect to mains whilst
STANDBY m
holding down the
button on the video recorder.
The Department of Trade and Industry operates a Radio Investiga-
tion Service to help TV licence holders improve reception of BBC
and ITC programmes where these are being spoilt by interference.
If your dealer cannot help, ask at a Main Post Office for the booklet
’How to Improve Television and Radio Reception’.
All stored data will be reset (cleared).
Cassette jammed:
•
Don’t use force. Pull out the mains plug for a moment.
Remote control does not operate:
•
Remote control not pointed toward the video recorder.
Batteries are exhausted.
•
No playback from video recorder:
•
No recording on the cassette.
•
The VCR programme number on the TV set was incorrectly
selected or incorrectly set.
•
The connecting cable between the TV set and the video
recorder has come loose.
Poor playback from video recorder:
•
•
•
TV set not properly adjusted.
Cassette badly worn or of poor quality.
Read the section about ’How to eliminate picture disturbance’ in
chapter ’PLAYBACK’.
No recording possible:
•
TV channel not stored or wrongly selected.
•
Cassette with erase protection has been loaded.
Programmed recording does not function:
•
•
•
TIMER not set properly.
Time/date wrongly programmed.
A cassette with erase protection has been loaded.
Picture or sound interference on TV reception e.g. when
tuned to ’CH5’:
•
Turn to Chapter 4 ’SPECIAL FEATURES’ and read in the section
’Playback via the aerial cable’ the note ’Adjusting the modulator
frequency’ as well as the note ’Switching off the modulator’.
Have your aerial checked.
•
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3103 166 19501 (WwnnNNNwwnwNNnwNwwnNNwNwnNnwwN)
VR 175
7443/001
Download from Www.Somanuals.com. All Manuals Search And Download.
|