Philips Universal Remote DRC800 User Manual

2. Follow the diagram inside the  
battery case to insert the new  
batteries.  
3. Enter the four-digit code. The  
device key LED turns off briefly  
after each key press.  
The device key’s LED blinks three  
times, indicating it has unlocked the  
volume control for all devices.  
Tip: Note the code set that worked, in  
My remote is not responding  
Press this  
Key  
Press this  
Key  
case you must re-code your remote:  
To…  
To…  
Review the information in  
“Using Your Remote”to make  
sure that the key you pressed is  
active for the device you are  
controlling.  
DVD/VCR:  
TV:  
AUDIO:  
See “Checking Codes”for more  
information on noting code sets.  
Motorola DRC800 4-in-1  
Universal Remote Control  
You have ten minutes to replace the  
batteries before your remote loses  
memory.  
Note: You have 10 seconds to press  
each digit. If it takes longer than  
that, the remote “times out” and  
you must begin again.  
Mute current audio  
feed  
These functions are set  
by your cable provider  
REASSIGNING DEVICE KEYS  
These functions are set  
by your cable provider  
Each device key accesses a specific  
type of device (for example, the DVD/  
VCR key can only be programmed to  
control a DVD player, VCR, DVR, or  
HTIB system). This makes it easier to  
search for a code if your device’s code  
does not appear on the list provided.  
Jump among pre-  
selected favorite  
channels (only  
available in CABLE  
mode)  
Make sure you are controlling  
the device you think you are. See  
“Using Your Remote”for more  
information on choosing a  
device to control.  
4. If the remote recognizes the  
code, the device key’s LED blinks  
three times. You can now test the  
remote by pressing POWER. If  
your device responds (turns off),  
you have found the right code. If  
your device does not respond,  
repeat steps 2 - 3 with the next  
code in the list..  
USING YOUR REMOTE  
Enter a channel or  
device code number. To  
access channels lower  
than 100, you may  
need to enter 3 digits.  
For example, to access  
channel 2, press 0-0-2.  
For channel 22, press  
0-2-2.  
To select a device to control, simply  
press one of the device mode keys (TV,  
AUDIO, DVD/VCR, CABLE) at the top of  
your remote. After you set up the  
remote to control that device, you may  
begin using the device.  
CHECKING CODES  
Make sure your batteries are  
good. If battery power is low,  
your remote enters a “Low  
Battery Condition” to conserve  
battery power for retaining your  
settings. See “Installing  
1. Press and hold a device mode  
key (AUDIO, DVD/VCR, or TV) for  
at least six seconds. The LEDs  
for each device key light up, then  
the key for the device you  
Note: Favorite  
channels must be pre-  
selected through the  
Electronic  
Programming Guide  
before this key works.  
Your new remote allows you to change  
the type of device that may be  
assigned to a device key. That way, if  
you have two TVs, for example, you  
can control them both by changing the  
type of device the DVD/VCR or AUDIO  
key controls.  
See “Programming Device Control”  
for more information on identifying a  
specific device to a device key.  
selected remains on.  
If the remote does not recognize  
the code, the LED will turn off.  
Retry the code (by repeating  
steps 2-3 using the next code  
listed for your brand), or search  
for a device code. See “Searching  
for Codes”.  
Batteries”for more information  
on changing the batteries.  
2. Enter 9 9 0 to tell the remote you  
are verifying the device code.  
The LED blinks twice.  
Input  
Select the video source  
Display the help screen  
(only available in  
CABLE mode)  
Press this  
To…  
Reset all settings:  
Aspect  
Change the viewing  
aspect (if available)  
1. Press and hold the device mode  
key (TV, AUDIO, DVD/VCR, or  
Cable) corresponding to the type  
of device you want the  
Key  
Press and hold a device  
mode key (TV, AUDIO, DVD/  
VCR, or Cable) or at least  
six seconds. The LED for  
each device key lights up,  
then the key for the device  
you selected remains on.  
3. Press 1, then count the LED  
blinks and write down the  
number. If the LED does not  
blink, the number is 0. This is  
the first digit of the device code.  
Press 2, 3, and 4 to obtain all  
four-code digits.  
Return to last selected  
channel  
PIP ON/OFF  
PIP SWAP  
Tu r n Pi c tu re-in -  
Picture (PIP) on or off  
(if available)  
Turn the selected  
device ON or OFF  
reassigned key to control (for  
example, TV) for at least six  
seconds. The LED for each  
device key lights up, then the key  
for the device you selected  
remains on.  
VOL +/-  
CH +/-  
Increase or decrease  
volume  
SEARCHING FOR CODES  
Audio, DVD/VCR, Select a device  
Swap the PIP signal to  
the main display (if  
available)  
TV, Cable  
If none of the codes listed under  
“Device Codes”on the back of this  
guide match your device, you can  
search for a set of commands that will  
work. Your remote will sample all the  
codes in its system for that device  
mode to find one that will allow you to  
control your device.  
Select the next or  
previous channel  
Direct access to Video  
On Demand (VOD),  
where available  
Enter 9 8 1.  
PIP Move  
Move the position of  
the PIP display  
CHANGING VOLUME LOCK  
The LED blinks twice to indicate  
that your remote is returned to  
its factory settings. You will need  
to reset all device code settings.  
See “Programming Device  
Control”.  
Move up or down  
through menu screens  
or the Electronic  
Program Guide  
2. Enter 9 9 2.  
Direct access to Pay Per  
View (PPV)  
programming (where  
available)  
User Guide  
Locking the volume controls to a  
single device makes it easier to control  
volume, without having to guess  
whether the volume will change. If you  
lock the remote's volume controls to  
the TV (for example), you will always  
be able to change the volume to the  
level you want, without having to  
adjust it on multiple devices.  
PIP CH +/-  
Select the next or  
previous channel in the  
PIP display (the main  
display does not  
change)  
3. Press the device mode key you  
want to reassign (for example,  
AUDIO). That mode key’s LED  
blinks three times and turns off,  
indicating that it has been  
reassigned.  
OVERVIEW  
Exit any On-Screen  
Display (OSD) and  
return to regular  
viewing  
1. Press and hold a device mode  
key (AUDIO, DVD/VCR, or TV) for  
at least six seconds. The LED for  
each device key lights up, then  
the key for the device you  
REW  
PLAY  
FFWD  
Rewind VCR, DVD,  
VOD , DVR, or HTIB  
Your new Motorola DRC800 universal  
4-in-1 remote operates your Motorola  
or or other manufacturer's cable set-  
top box and up to three other devices.  
ADDITIONAL INFORMATION  
The reassigned key automatically uses  
the same device code as the key you  
selected in Step 1. If your second  
device uses a different code, you may  
program it for the new code. See  
“Programming Device Control”.  
Play VCR, DVD, VOD ,  
DVR, or HTIB  
PROGRAMMING DEVICE  
CONTROL  
The Motorola DRC800 does not have  
any user-serviceable parts. Opening  
the case, except for the battery cover,  
may cause permanent damage to your  
Motorola remote control.  
Display channel and  
program information  
selected remains on.  
In addition, the DRC800 provides  
advanced features such as Digital  
Video Recording (DVR) control and  
Picture-in-Picture (PIP) support.  
1. Press and hold the device mode  
key (TV, AUDIO, DVD/VCR, or  
Cable) corresponding to the  
device you want to control  
Fast Forward VCR,  
DVD, VOD , DVR, or  
HTIB  
2. Press a function key (such as  
Power or Mute). The following  
function keys are valid for  
Searching (Power is  
Each of the additional device keys  
controls a particular type of device.  
For example, the DVD/VCR key  
controls your VCR, DVR, or DVD  
player, but not your TV, unless you  
specify otherwise. See “Reassigning  
Device Keys”.  
Access the cable guide  
No part of this publication may be  
reproduced, transmitted, transcribed,  
stored in any retrieval system, or  
translated to any language, in any  
form, or by any means, electronic,  
mechanical, optical, manual, or  
otherwise, without the prior written  
permission of Motorola.  
volume for at least six seconds.  
The LED for each device key  
lights up, then the key for the  
device you selected remains on.  
You can lock volume control to any of  
these devices, to make adjusting your  
home entertainment volume easier.  
See “Changing Volume Lock”. The  
DRC800 comes from the factory  
without the volume locked to any  
specific device.  
Note: You may not reassign the Cable  
device key to another type of device.  
RECORD  
PAUSE  
STOP  
Record to VCR or DVR  
Access any OSD for the  
currently selected  
device  
recommended):  
Power  
Mute  
Play  
CH +  
Stop  
Pause VCR, DVD, VOD  
or DVR  
Assigning a Key back to Its Original  
Device Type:  
1. Press and hold the device mode  
key (TV, AUDIO, DVD/VCR, or  
Cable) you want to reset to its  
original type (for example,  
Move up through any  
OSD or cable guide  
menu  
!
"
#
$
2. Press Volume +.  
This device  
key…  
Controls this type of  
device…  
The device keys LED blinks three  
times, indicating it has locked the  
volume control to the device you  
selected. The AUDIO device key always  
controls its own volume, regardless of  
the device is locked to volume control.  
Stop VCR, DVD, VOD  
or DVR  
You can also change what type of  
device each mode key controls. See  
“Reassigning Device Keys”.  
Move down through  
any OSD or cable guide  
menu  
TV  
TV  
MOTOROLA and the stylized M logo  
are registered trademarks in the US  
Patent and Trademark Office. All other  
product and service names are the  
property of their respective owners.  
Copyright Motorola, Inc. 2003.  
Replay the previous  
few seconds of a  
program (only  
available with DVR  
models)  
DVD/VCR  
DVD, VCR, DVR,  
HTIB, TV/VCR,  
TV/VCR/DVD,  
and TV/DVD  
The device key’s LED blinks  
three times, then turns off.  
AUDIO) for at least six seconds.  
The LED for each device key  
lights up, then the key for the  
device you selected remains on.  
Move left through any  
OSD or cable guide  
menu  
Operating Range  
3. Press !. The remote will send  
the IR command for the function  
you pressed in Step 2.  
Note: If you reassign AUDIO to  
another device, such as a second TV,  
the second TV will always control its  
own volume.  
Your remote controls devices from up  
to 50 ft (15 m) away if you are directly  
in front of the device, or from up to 20  
ft (6 m) away if you are off to either  
side.  
Cable  
Audio  
Cable box only  
2. Enter 9 9 2. The mode keys LED  
Display a list of  
Move right through any  
OSD or cable guide  
menu  
4. If the device performed the  
function you pressed, press OK.  
The remote will now control the  
device you selected in Step 1.  
blinks three times and turns off.  
Amplifier, Tuner  
M1072  
11/03  
programs that you  
recorded. This will  
allow you to select one  
for viewing (only  
available with DVR  
models)  
3. Press the device mode key you  
selected in Step 1 again. The  
mode key’s LED blinks three  
times and turns off.  
To sp e ci f y a d e v ice  
Unlocking Volume Control:  
Select the currently  
highlighted OSD menu  
or cable guide choice  
1. Look up the device you want to  
control in the device code list on  
the back of this guide.  
1. Press and hold a device mode  
key (TV, AUDIO, DVD/VCR, or  
Cable) corresponding to the  
device currently locked to the  
volume controls for at least six  
seconds. The LED for each  
device key lights up, then the key  
for the device you selected  
remains on.  
INSTALLING BATTERIES  
If the device did not perform the  
function you pressed, repeat step  
3. Press " to retry the previous  
code.  
4. Program the restored mode key  
to control a device. See  
Your remote requires 2 AAA batteries.  
The first set of batteries is included,  
and should last up to 6 months under  
normal usage.  
This product uses technologies  
licensed under one or more of the  
following U.S. patents:  
6,587,067  
6,195,033  
6,496,135  
2. Press and hold a device key  
(AUDIO, DVD/VCR, or TV) for at  
least six seconds. The LEDs for  
each device key light up, then the  
LED for the device you selected  
remains on.  
View the previous or  
next day’s cable guide  
Displays live television  
programming (only  
available with DVR  
models)  
“Programming Device Control”.  
These functions are set  
by your cable provider  
TROUBLESHOOTING  
1. Remove the battery case cover  
and the old batteries (if  
necessary).  
If you have trouble with your remote,  
try the following steps in order.  
2. Press Volume -.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Camera Accessories SCB4350NB User Manual
Philips Cassette Player AQ 6688 User Manual
Philips Home Theater Screen BDL4620QL User Manual
Philips Portable DVD Player PET741 37 User Manual
Philips Projection Television 43PP8545 69 User Manual
Philips Stereo System SWV3434W User Manual
Pioneer Car Stereo System DEH 5200SD User Manual
Plantronics Wireless Office Headset CS60 USB DECT User Manual
Playskool Microphone Music Microphone User Manual
Powermatic Saw PM1500 User Manual