Se ction 530
ISDN
Digital Business System
Re fe re nce
Ma nua l
for CPC-EX Ve rs ion 2.3
Doc. No. 504X00301C
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
About This Manual
Overview............................................................................................................................ vii
Related Documents............................................................................................................ vii
Chapter 1. Introduction to the ISDN Interface
Overview................................................................................................................................. 1-3
Description of the ISDN Interface.................................................................................... 1-3
Framing Options ............................................................................................................... 1-3
Pre-Installation Requirements................................................................................................. 1-4
Ordering ISDN.................................................................................................................. 1-4
What You Must Purchase ................................................................................................. 1-8
Chapter 2. Installation
Guidelines ............................................................................................................................... 2-3
Hardware Requirements ................................................................................................... 2-3
Maximums ........................................................................................................................ 2-3
Trunk Assignments for Single-Cabinet Systems.............................................................. 2-5
Trunk Assignments for Double-Cabinet Systems ............................................................ 2-6
Installation Procedures.......................................................................................................... 2-12
Installing the CSU........................................................................................................... 2-12
Installing an ISDN in a Single Cabinet........................................................................... 2-14
Installing ISDN in a Double Cabinet with the ISDN in the Slave.................................. 2-21
Installing ISDN in a Double Cabinet with ISDNs in the Master and Slave ................... 2-23
Chapter 3. Quick-Start Programming
Before You Begin ................................................................................................................... 3-3
Programming Initial ISDN Options........................................................................................ 3-4
Minimum Programming ................................................................................................... 3-4
Multiple DID Programming.............................................................................................. 3-9
Typical Central Office Configurations ........................................................................... 3-10
Revised April 2000
DBS-EX23-530
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Programming Reference
ISDN System Settings ............................................................................................................ 4-3
System Size....................................................................................................................... 4-3
T1/ISDN............................................................................................................................ 4-3
Clock Settings................................................................................................................... 4-4
System-Wide Timers .............................................................................................................. 4-7
Digital Pad Settings .............................................................................................................. 4-12
Extension Port Settings................................................................................................... 4-14
Trunk Port Settings ......................................................................................................... 4-15
Master and Slave Settings..................................................................................................... 4-16
Trunk Configuration ....................................................................................................... 4-16
Trunk Signaling .............................................................................................................. 4-16
Alarm Settings ...................................................................................................................... 4-17
Alarm Descriptions......................................................................................................... 4-17
Alarm Transmission Options.......................................................................................... 4-20
Alarm Timers ................................................................................................................. 4-21
Error Counters for FF Alarm Keys................................................................................. 4-22
Alarm Relay Controls ..................................................................................................... 4-25
Trunk Settings....................................................................................................................... 4-28
Extension Settings................................................................................................................. 4-34
FF Key Settings .................................................................................................................... 4-35
Special ISDN Function Codes .............................................................................................. 4-36
Appendix A CPC-EX 2.3 Updates
iv
DBS-EX23-530
Revised 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Figure 2-1
Figure 2-2
Figure 2-3
Figure 2-4
Figure 2-5
Figure 2-6
Figure 2-7
Figure 2-8
Figure 2-9
CSU installation .......................................................................................... 2-13
SCC-B Switch 4 .......................................................................................... 2-15
Connector 4 (CN4) strapping, Sync Unit .................................................... 2-15
Sync Unit installation .................................................................................. 2-16
MDF card installation ................................................................................. 2-17
Sync Unit and ISDN connection, single-cabinet installation ..................... 2-18
RJ48 pinouts, CN1 connector ..................................................................... 2-19
ISDN cabinet connections, single-cabinet installation ............................... 2-20
Sync cable connections, double-cabinet with an ISDN in the slave ........... 2-22
Figure 2-10 Clock sync cable and sync cable connections, double-cabinet installation 2-24
Figure 4-1
Figure 4-2
Figure 4-3
Circuit-type numbers .................................................................................. 4-12
Default pad values ...................................................................................... 4-13
Pad Nos. ...................................................................................................... 4-13
Revised April 2000
DBS-EX23-530
v
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
Table 1-1
Table 4-1
Table 5-1
Table 5-2
Table 5-3
Table 6-1
Table 6-2
Table 6-3
Table 6-4
Table 6-5
Table 6-6
Table 6-7
Table 6-8
Table 6-9
Table 6-10
Table 6-11
Table 7-1
Table 7-2
Guidelines for ordering ISDN services ......................................................... 1-4
ISDN alarm definitions ............................................................................... 4-17
ISDN Hardware requirements for single-cabinet systems ............................ 1-8
ISDN Hardware requirements for double-cabinet systems ......................... 1-8
CSU equipment required for ISDN ............................................................. 1-9
EC/TRK slot usage for ISDN ....................................................................... 2-3
ISDN and analog trunk assignments, DBS 40 ............................................. 2-5
ISDN and analog trunk assignments, DBS 72 ............................................. 2-5
ISDN and analog trunk assignments, DBS 96 ............................................. 2-6
Maximum ISDN assignments for two-cabinet systems ............................... 2-7
ISDN and analog trunk assignments, DBS 40 + 40 .................................... 2-7
ISDN and analog trunk assignments, DBS 72 + DBS 72 ............................ 2-8
ISDN and analog trunk assignments, DBS 96 + DBS 40 ............................. 2-9
ISDN and analog trunk assignments, DBS 96 + DBS 72 .......................... 2-10
ISDN and analog trunk assignments, DBS 96 + DBS 96 .......................... 2-11
Switch settings for SW1 on the ISDN card ............................................... 2-18
ISDN alarm definitions ............................................................................... 4-17
Alarm-related programs ............................................................................. 4-18
vi
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Overview
This manual provides an overview of the DBS ISDN Interface, along with
installation and programming instructions when used with CPC-EX Version
2.2. Appendix A provides updates for CPC-EX version 2.3 as well.
The following table summarizes each chapter contained in this manual.
Chapter Title
Purpose
Introduction to the Provides an overview of the DBS ISDN Interface, plus
1
ISDN Interface
information on pre-installation requirements.
Installation
Provides step-by-step instructions on installing the DBS
ISDN hardware.
2
Summarizes the programs that are essential to ISDN
installation.
3
4
Quick-Start
Programming
Contains a complete list of ISDN programming commands.
Each command description includes a list of the available
options and the associated programming addresses.
Programming
Reference
Contains a description of enhanced features and software
corrections provided with CPC-EX 2.3.
A
CPC-EX 2.3
Updates
Related Documents
For general instructions on DBS hardware installation, see Installation
(Section 300). For an introduction to DBS programming, see Programming
Guidance (Section 400).
Revised April 2000
DBS-EX23-530
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Introduction to the ISDN
Interface
This chapter provides an overview of the ISDN Interface. It also describes
pre-installation requirements for the ISDN.
The following table summarizes the topics contained in this chapter.
Topic
Page
Revised April 2000
DBS-EX23-530
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to the ISDN Interface
Overview
Overview
Description of the ISDN Interface
The ISDN Interface is a Primary Rate Interface (PRI) digital trunk card that
provides 23 voice channels (“B” channels) and a control channel (“D”
channel) over a four-wire circuit.
ISDN lines can be leased from local exchange carriers and long-distance
carriers.
Note: The current version of the ISDN supports voice communications only.
Data can be transmitted only if it reaches the ISDN in analog form. Examples of
analog data that can be transmitted over the ISDN include fax transmissions or
PC files that have been converted into analog form using a modem.
Framing Options
The ISDN Interface takes an 8-bit sample from each of the 23 voice channels.
These samples are grouped into 23 bearer time slots, and 1 data channel time
slot.
Since each of the 24 time slots contains 8 bits, the number of sampling bits in
each frame equals 192 (24 x 8 = 192). In addition, a framing bit is added to
the end of each frame to mark where the frame ends. The addition of the
framing bit results in a 193-bit frame.
The ISDN transmits these 193-bit frames at a rate of 8000 per second. The
total number of frames (193) multiplied by the frame speed (8000 per second)
results in a total transmission rate of 1.544 Mbps.
ESF Framing Formats
The extended superframe (ESF) format transmits the sampling frames in
groups of 24 with 23B (bearer) channels at 64 Kbps and 1D (Data) channel at
64 Kbps. With the addition of 2.0 Kbps error checking CRC, 2.0 Kbps
framing, and 4.0 Kbps datalink facility, the total capacity is 1.544 Mbps.
Revised April 2000
DBS-EX23-530
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Installation Requirements
Introduction to the ISDN Interface
Pre-Installation Requirements
Use the following guidelines to prepare your site for ISDN installation.
Ordering ISDN
The ISDN PRI provides a flexible method of providing access to the PSTN
(Public Switched Telephone Network). Because of the numerous ways that
an ISDN span can be configured by the CO, it is essential that the DBS
configuration and the provisioning of the CO be compatible. The following
tables are provided to identify the critical parameters that must be set for
proper operation. The following tables provides a list of information that must
be gathered about the CO as well as the type of information which the CO
will need to know regarding the DBS system.
#
Information Needed from CO
Comments / Examples
1
Manufacture of CO and software load
5E11 (5ESS with load 11), DMS-100 with
NA008
2
3
4
Is local dialing 7 digits, 10 digits or a com-
bination.
For long distance dialing does the CO
want to see a leading “1” or not.
1-770-555-1212 or 770-555-1212
For international dialing does the CO want 011-(15-digit number) or (15-digit number)
to see the leading “011” or not.
#
Typical Information for CO
Installation Address
Comments (Examples)
1
2
3
4
5
Is this a new installation?
Extended wiring beyond telephone room?
Main telephone number of installation
Contact person for installation
Contact for order information
Billing name
6
7
8
Billing address
Long distance Carrier InterLATA (PIC)
This identifies the carrier who will provide
long distance access.
1-4
DBS-EX23-530
April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to the ISDN Interface
Pre-Installation Requirements
9
Long distance Carrier (IntraLATA)
(LPIC)
This identifies the carrier who will provide
access for connections, which are not local
but are still within the local LATA.
10 Request date of installation
11 Facility type
ISDN PRI
12 Facility quantity
1 or 2 spans
NOTE THAT THE FOLLOWING ITEMS MUST BE PROVIDED ON A PER SPAN BASIS
13 Signaling code
DS-1 (1.544 Mbps)
14 Line coding
B8ZS (Binary 8 Zero Substitution)
ESF (Extended Superframe)
15 Framing Format
16 Bearer configuration
17 Quantity of B (bearer) channels
23B + 1D - Max. setting (must have 1 D
channel)
Or XB + 1D where X is 1-23 for a frac-
tional span
18 Call type
Two Way
19 Quantity of phone numbers
Block of 20 numbers are generally
assigned. With DID, note that the total
number of telephone numbers will exceed
the total number of B channels.
20 Number of incoming digits to CPE (Cus-
tomer Premise Equipment – DBS)
Select 4 digits. This is used with DID.
21 ISDN PRI Protocol
5ESS Custom or
DMS-100 Custom (NTNAPRI) or
4ESS
22 Glare Resolution
CPE yield to CO
23 Channel selection used by CO
24 Source of Calling Party Number
High-to-Low B-channel selection
Calling Party Number must be sourced by
the CO.
25 Service Options
ANI – Automatic Numbering Indication
Hunt group -
MegaCom –only for 4ESS operation
Note: 1- If two spans are implemented, each must have a separate D channel,
i.e. D channel sharing is NOT permitted.
Revised April 2000
DBS-EX23-530
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Installation Requirements
Introduction to the ISDN Interface
Copy the following tables for each site and span that is to be installed.
Complete all information and use for future reference. Note that certain
parameters are shown with default values.
#
Information Needed from CO
Site Information
1
Manufacture of CO and software load
2
3
4
Is local dialing 7 digits, 10 digits or a
combination.
For long distance dialing does the CO
want to see a leading “1” or not.
For international dialing does the CO
want to see the leading “011” or not.
#
Typical Information for CO
Installation Address
Site Information
1
2
3
Is this a new installation?
Extended wiring beyond telephone
room?
4
5
Main telephone number of installa-
tion
Contact person for installation
Contact for order information
Billing name
6
7
8
Billing address
Long distance Carrier InterLATA
(PIC)
9
Long distance Carrier (IntraLATA)
(LPIC)
10
1 1
12
Request date of installation
Facility type
ISDN PRI
Facility quantity
1-6
DBS-EX23-530
April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to the ISDN Interface
Pre-Installation Requirements
Span Item
Master Cabinet Span
Slave Cabinet Span
DS-1
13
14
15
16
17
18
19
20
Signaling code
DS-1
Line coding
B8ZS
B8ZS
Framing Format
ESF
ESF
Bearer configuration
Quantity of B (bearer) channels
Call type
Voice or Voice/Data
Voice or Voice/Data
Two-way
4 digits
Two-way
4 digits
Quantity of phone numbers
Number of incoming digits to
CPE (Customer Premise
Equipment –DBS)
21
22
23
ISDN PRI Protocol
Glare Resolution
CPE yield to CO
CPE yield to CO
Channel selection used by CO High-to-Low B-chan-
nel selection
High-to-Low B-chan-
nel selection
24
25
Source of Calling Party Num-
ber
Calling Party Number
sourced by the CO.
Calling Party Number
sourced by the CO.
Service Options
Revised April 2000
DBS-EX23-530
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Installation Requirements
Introduction to the ISDN Interface
What You Must Purchase
The following items must be purchased to install ISDN.
DBS Equipment
If you are installing the ISDN in a single-cabinet system, order the equipment
Table 1-1. ISDN Hardware requirements for single-cabinet systems
CPC-EX
SCC-B
ISDN Trunk Card MDF Card
Sync Unit
(VB-43415)
(VB-43421)
(VB-43571)
(VB-43562)
(VB-43563)
1
1
1
1
1
(See Note 1.)
(See Note 3.)
Notes:
1. SCC-B with ROM 1.3 or later is required if the central office does not provide ISDN dial tone.
2. Fractional (per port) Assignments requires the VB-43511A version of the loop start trunk card.
3. COP 1.07 or later is required with ISDN PRI Trunk Card VB-43571 for CPC-EX 2.2.
Table 1-2. ISDN Hardware requirements for double-cabinet systems
ISDN
Location
CPC-EX
(VB-43415) (VB-43421) Card
SCC-B
ISDN Trunk MDF
Card
Sync
Unit
ISDN Cable Cable Kit
(VB-43564) (VB-43110)
(See Note 2.)
(See Note 1) (VB-43571) (VB-43562) (VB-43563)
(See Note 3.)
ISDN in the
Master
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
0
1
1
1
1
1
ISDN in the
Slave
ISDN in both
Master and
Slave
Notes:
1. SCC-B with ROM 1.3 or later is required if the central office does not provide ISDN dial tone.
2. Version 1.2 of the Cable Kit is required for ISDN.
3. Fractional (per port) Assignments requires the VB-43511A version of the loop start trunk card.
4. COP 1.07 or later is required with ISDN PRI Trunk Card VB-43571 for CPC-EX 2.2.
1-8
DBS-EX23-530
April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to the ISDN Interface
Pre-Installation Requirements
CSU Equipment
The installer must provide a Channel Service Unit (CSU) plus CSU cabling.
The CSU equipment must meet the specifications contained in Table 1-3. See
Table 1-3. CSU equipment required for ISDN
Item
Specifications
Vendors
CSU
The Channel Service Unit (CSU) must
The following CSUs have been used suc-
comply with FCC Part 15 and Part 68. The cessfully with the DBS ISDN.
CSU is installed between the DBS and the
public network. The CSU provides alarm,
diagnostic, and monitoring functions, as
well as network protection.
Kentrox
Kentrox T-SERV II
or
Kentrox T-SMART
(Kentrox can be contacted at 1-800-733-
5511.)
CSU
Each CSU requires a network cable and an equip-
ment cable. The network cable connects from the
CSU to the network interface. The equipment cable
connects from the CSU to the DBS ISDN MDF
card.
For Kentrox CSUs
Cabling
Kentrox offers prefabricated cables for their CSUs.
For the network cable, order part number 01-
93010151. For the equipment cable, order part
number 01-93010121.
For Kentrox CSUs
If you fabricate your own cables, use 24 AWG
stranded cable that includes shielding for each pair.
The network cable requires a female DB-15 con-
nector and an RJ48C connector. The equipment
cable requires a male DB-15 connector and an
RJ48C connector.
Belden (Richmond, IN) offers stranded cable that
complies with these specifications. Order part
number 8723.
To simplify installation, you can order the prefabri-
cated cables shown in the “Vendors” column.
If you fabricate your own ISDN cables, you should
use 24 AWG stranded cable that includes shielding
for each pair. For best results, use the cable listed
under “Vendors.”
For Premier CSUs
You must fabricate your own cables for the Premier
CSU. The network cable requires two RJ48C con-
nectors. The equipment cable connects to an RJ48C
connector on the ISDN MDF card and to four
screw-down terminals on the CSU.
For both cables, use 24 AWG stranded cable that
includes shielding for each pair. For best results,
use the cable listed under “Vendors.”
Revised April 2000
DBS-EX23-530
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Installation Requirements
Introduction to the ISDN Interface
1-10
DBS-EX23-530
April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Installation
This section describes guidelines and procedures for installing the ISDN
Interface. Once the ISDN Interface is installed, refer to Chapter 3 - “Quick
Start Programming” or Chapter 4 - “Programming Reference” for
programming instructions.
This chapter covers the following topics.
Topic
Page
Revised April 2000
DBS-EX23-530
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2
DBS-EX22-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Guidelines
Guidelines
Read the following guidelines before beginning ISDN installation.
Installation instructions begin on page 2-14.
Hardware Requirements
• The system configuration determines what cards and cables must be
purchased for ISDN. See “DBS Equipment” on page 1-8 for more
information.
• The installer must provide a Channel Service Unit (CSU) that complies
with FCC Part 15 and Part 68. The CSU is installed between the DBS and
the public network. The CSU provides alarm, diagnostic, and monitoring
functions, as well as network protection.
See “CSU Equipment” on page 1-9 for details on purchasing CSUs.
Maximums
• One ISDN card can be installed per cabinet; the ISDN card must be
installed in the “EC/TRK” slot.
• The number of ISDN cards that can be installed in two-cabinet systems
maximums for two-cabinet systems.
Note: The DBS 72 + DBS 40 combination does not support ISDN.
Table 2-1. EC/TRK slot usage for ISDN
System Size
EC/TRK Slot
Usage for ISDN
Master
Slave
Yes
No
DBS 40 + DBS 40 No
DBS 72 + DBS 40 No
DBS 72 + DBS 72 No
DBS 96 + DBS 40 Yes
DBS 96 + DBS 72 Yes
DBS 96 + DBS 96 Yes
Yes
Yes
Yes
Yes
Revised April 2000
DBS-EX23-530
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Guidelines
Installation
• Fractional ISDN can be used when fewer than 23 ISDN trunks are needed.
Fractional ISDN allows you to use only a portion of the 23 channels
provided on the ISDN card.
• Fractional ISDN per port assignments require the VB-43511A version of
the loop start trunk card. The older VB-43511 version may be used with
fractional ISDN but requires that the trunks be assigned in blocks of 8.
• Though each ISDN Interface provides 23 trunk channels, ISDN trunks do
not increase the overall trunk capacity of the DBS. Each ISDN channel
subtracts from the total number of analog trunks that can be installed. The
number of analog trunks that can be used are decremented in quantities of
1 for each ISDN channel user.
digital trunks assignments based on system size.
The trunk numbering shown in these tables is determined by backplane
trunk port assignments. Therefore, the numbering cannot be changed.
Note: Analog trunks are numbered beginning with “1.” ISDN trunk
channels are numbered beginning with the highest trunk channel used.
2-4
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Guidelines
Trunk Assignments for Single-Cabinet Systems
• Programming is not required to associate trunk ports with slot locations.
However, you must use programming to specify that a combination of
ISDN and analog trunks is installed, and you must also specify how many
ISDN channels are used.
• Fractional ISDN per port assignments require the VB-43511A version of
the loop start trunk card. The older VB-43511 version may be used with
fractional ISDN but requires that the trunks be assigned in blocks of 8.
Table 2-2. ISDN and analog trunk assignments, DBS 40
Trunk
Number
Fractional ISDN
using 16 Channels
Fractional ISDN
using 8 Channels
1
ISDN channel 16
↓
Analog trunk 1
↓
↓
8
9
↓
ISDN channel 9
ISDN channel 8
↓
Analog trunk 8
ISDN channel 8
↓
16
ISDN channel 1
ISDN channel 1
Note: Since the DBS 40 supports a maximum of 16 trunks, all 23
channels of the ISDN cannot be used.
Table 2-3. ISDN and analog trunk assignments, DBS 72
Trunk
Number
23-Channel ISDN
Fractional ISDN
using 16 Channels
Fractional ISDN
using 8 Channels
1
Analog trunk 1
ISDN channel 23
↓
Analog trunk 1
Analog trunk 2
↓
Analog trunk 1
Analog trunk 2
↓
2
↓
8
ISDN channel 17
ISDN channel 16
↓
Analog trunk 8
ISDN channel 16
↓
Analog trunk 8
Analog trunk 9
↓
9
↓
16
17
↓
ISDN channel 9
ISDN channel 8
↓
ISDN channel 9
ISDN channel 8
↓
Analog trunk 16
ISDN channel 8
↓
24
ISDN channel 1
ISDN channel 1
ISDN channel 1
Revised April 2000
DBS-EX23-530
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guidelines
Installation
Table 2-4. ISDN and analog trunk assignments, DBS 96
Trunk
Number
23-Channel ISDN
Fractional ISDN
using 16 Channels
Fractional ISDN
using 8 Channels
Analog trunk 1
↓
1
↓
Analog trunk 1
↓
Analog trunk 1
↓
8
Analog trunk 8
Analog trunk 9
ISDN channel 23
↓
Analog trunk 8
Analog trunk 8
9
Analog trunk 9
Analog trunk 9
10
↓
↓
↓
16
17
↓
ISDN channel 17
ISDN channel 16
↓
Analog trunk 16
ISDN channel 16
↓
Analog trunk 16
Analog trunk 17
↓
24
25
↓
ISDN channel 9
ISDN channel 8
↓
ISDN channel 9
ISDN channel 8
↓
Analog trunk 24
ISDN channel 8
↓
32
ISDN channel 1
ISDN channel 1
ISDN channel 1
Trunk Assignments for Double-Cabinet Systems
• When ISDN is used in a two-cabinet system, the number of ISDN channels
that can be assigned in each cabinet depends on the master/slave
designation.
• Fractional ISDN per port assignments require the VB-43511A version of
the loop start trunk card. The older VB-43511 version may be used with
fractional ISDN but requires that the trunks be assigned in blocks of 8.
The following table shows the maximum number of ISDN channels that
can be assigned in two-cabinet systems.
2-6
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Guidelines
Table 2-5. Maximum ISDN assignments for two-cabinet systems
System Size
Master
Slave
DBS 40 + DBS 40 8 analog trunks
DBS 72 + DBS 72 16 analog trunks
16 ISDN trunks
23 ISDN trunks
1 analog trunk
DBS 96 + DBS 40 23 ISDN trunks
9 analog trunks
16 ISDN trunks
DBS 96 + DBS 72 23 ISDN trunks
9 analog trunks
23 ISDN trunks
1 analog trunk
DBS 96 + DBS 96 23 ISDN trunks
9 analog trunks
23 ISDN trunks
9 analog trunks
• Two-cabinet systems use the same trunk numbering scheme as single-
cabinet systems: analog trunks are numbered from “1” upward; ISDN
trunk channels are numbered downward from the highest channel used.
using the maximum number of ISDN channels.
Table 2-6. ISDN and analog trunk assignments, DBS 40 + 40 (16-channel fractional ISDN in the
slave)
Trunk
Master Cabinet
Slave Cabinet
Number
1
Analog trunk 1
↓
↓
Ν/Α
8
Analog trunk 8
9
ISDN channel 16
↓
↓
N/A
16
17
↓
ISDN channel 9
ISDN channel 8
↓
Ν/Α
24
ISDN channel 1
Revised April 2000
DBS-EX23-530
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guidelines
Installation
Table 2-7. ISDN and analog trunk assignments, DBS 72 + DBS 72 (23-channel ISDN in the slave)
Trunk
Master Cabinet
Slave Cabinet
Number
1
Analog trunk 1
↓
↓
Ν/Α
8
Analog trunk 8
Analog trunk 9
↓
9
↓
N/A
16
17
18
↓
24
33
↓
40
41
↓
Analog trunk 16
Analog trunk 1
ISDN channel 23
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
Ν/Α
Ν/Α
Ν/Α
48
ISDN channel 1
2-8
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Guidelines
Table 2-8. ISDN and analog trunk assignments, DBS 96 + DBS 40 (23-channel ISDN in the master;
16-channel ISDN in the slave)
Trunk
Master Cabinet
Slave Cabinet
Number
1
Analog trunk 1
↓
↓
Ν/Α
8
Analog trunk 8
Analog trunk 9
ISDN channel 23
↓
9
10
↓
N/A
Ν/Α
Ν/Α
16
17
↓
24
25
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
32
33
↓
40
41
↓
ISDN channel 1
ISDN channel 16
Ν/Α
Ν/Α
↓
ISDN channel 9
ISDN channel 8
↓
48
ISDN channel 1
Revised April 2000
DBS-EX23-530
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guidelines
Installation
Table 2-9. ISDN and analog trunk assignments, DBS 96 + DBS 72 (23-channel ISDN in the master;
23-channel ISDN in the slave)
Trunk
Master Cabinet
Slave Cabinet
Number
1
Analog trunk 1
↓
↓
Ν/Α
8
Analog trunk 8
Analog trunk 9
ISDN channel 23
↓
9
10
↓
N/A
Ν/Α
Ν/Α
16
17
↓
24
25
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
32
33
34
↓
40
41
↓
48
49
↓
ISDN channel 1
Analog trunk 1
ISDN channel 23
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
Ν/Α
Ν/Α
Ν/Α
56
ISDN channel 1
2-10
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Guidelines
Table 2-10. ISDN and analog trunk assignments, DBS 96 + DBS 96 (23-channel ISDN in the master;
23-channel ISDN in the slave)
Trunk
Master Cabinet
Slave Cabinet
Number
1
Analog trunk 1
↓
↓
Ν/Α
8
Analog trunk 8
Analog trunk 9
ISDN channel 23
↓
9
10
↓
N/A
Ν/Α
Ν/Α
16
17
↓
24
25
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
32
33
↓
ISDN channel 1
Analog trunk 1
↓
Ν/Α
40
41
42
↓
48
49
↓
56
57
↓
Analog trunk 8
Analog trunk 9
ISDN channel 23
↓
ISDN channel 17
ISDN channel 16
↓
ISDN channel 9
ISDN channel 8
↓
Ν/Α
Ν/Α
Ν/Α
64
ISDN channel 1
Revised April 2000
DBS-EX23-530
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation
Installation Procedures
The following procedures provide step-by-step instructions for installing the
CSU and the ISDN Interface. The ISDN procedure that you should use
depends on the type of system you have and the number of ISDNs you are
installing.
If you’re installing ...
A ISDN in a single cabinet
Use this procedure...
“Installing an ISDN in a Single Cabinet” (page 2-
One ISDN in a double cabinets, with the “Installing an ISDN in a Double Cabinet with the
ISDN located in the slave
ISDN in the Slave” (page 2-21)
ISDNs in both the master and slave
“Installing an ISDN in a Double Cabinet with
ISDNs in the Master and Slave” (page 2-23)
Installing the CSU
The following instructions explain how to install the CSU. See “CSU
Equipment” on page 1-9 for specifications on CSUs and CSU cabling.
Note: The CSU can be powered locally or through the CO line. Also, a
locally powered CSU should be connected to an Uninterruptible Power
Supply (UPS) to provide battery backup in case of AC power failures.
1. Connect the equipment cable from the DBS MDF card to the equipment
side of the CSU, as shown in Figure 2-1.
2-12
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Procedures
Figure 2-1. CSU installation
2. Connect the network cable from the network side of the CSU to the
network demarcation point. (The network demarcation is typically an
RJ48C “smartjack.”)
3. Test the CSU cabling by performing the following steps.
Note: The following procedure can only be used with CSUs that provide a
local loopback. When testing the CSU, be sure it is set to “local loopback,”
rather than “line loopback.” Line loopback provides a loopback between
the CSU and the network.
The CSU can be tested only after the following parameters have been set.
For a summary of these parameters, see Chapter 3, “Quick-Start
Programming.” The page numbers included in the following table
reference detailed descriptions included in Chapter 4.
Parameter
Page No.
System Configuration
Revised April 2000
DBS-EX23-530
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation
Sync Source
Trunk Configuration
ISDN Trunk Type
b. Put the CSU in the local loopback mode.
c. Check the CFA LED on the ISDN card. If the LED is dark, the cabling
between the CSU and DBS is okay. If the LED is lit, go to the next step.
d. Check the cabling from the DBS to the CSU.
e. If you don’t find cabling errors, take the CSU out of local loopback
mode and reinstall the jumper on CN4 of the Sync Card.
f. If the CFA LED remains lit, check the cabling from the CSU to the
network demarcation point.
Installing an ISDN in a Single Cabinet
The following instructions explain how to install a ISDN in a single-cabinet
system. These instructions also apply when a ISDN is installed in only the
master cabinet of a two cabinet system.
If only one ISDN is installed in a two-cabinet system, it must be installed in
the cabinet specified in Table 2-1 on page 2-3.
Note: For systems consisting of a DBS 72 connected to a DBS 40, the ISDN
Interface cannot be used.
1. Before beginning ISDN installation, perform the “ISDN Function Reset”
command (FF1 9# 1# 1#). This command must be issued before the ISDN
can be installed properly.
2. Check SW4 on the SCC-B card. Be sure it is set to “Mode B.”
2-14
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Procedures
Figure 2-2. SCC-B Switch 4
M ode B
(C P C -B
CPC-EX)
M ode A
(CPC-A
CPC-AII)
SW 4
SCC-B Card
3. Check connector 4 (CN4) on the Sync Unit (VB-43563). Make sure that
When Pins 2 and 3 are strapped, the Sync Unit synchronizes the DBS
ISDN card with the signaling provided by the public network.
Figure 2-3. Connector 4 (CN4) strapping, Sync Unit
CN2
CN3
CN4
CN1
3
1
Free
N et
4. Attach the Sync Unit to the CPC-EX card.
Revised April 2000
DBS-EX23-530
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation
Note: Before attaching the Sync Unit, insert the three spacers provided
with the unit and remove the jumpers from CN2 of the CPC-EX card.
Figure 2-4. Sync Unit installation
2-16
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Procedures
Installation
6. Set SW1 on the ISDN card according to the following table.
These switch settings correspond to the distance between the DBS and the
CSU. To turn a switch on, flip it to the “up” position.
Table 2-11. Switch settings for SW1 on the ISDN card
SW
Distance from the DBS to the CSU
0 to 150 ft.
On
150-450 ft.
Off
450-655 ft.
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
Off
Off
On
Off
Off
Off
On
Off
On
Off
Off
Off
On
Off
On
Off
Off
Off
On
Not used
Not used
Not used
7. Install the ISDN card in the “EC/TRK” slot
8. Connect the Sync Cable from CN1 on the Sync Unit to CN5 on the ISDN
card.
Figure 2-6. Sync Unit and ISDN connection, single-cabinet installation
2-18
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Procedures
9. Connect the cable attached to CN3 on the MDF card to CN3 on the ISDN
10. Using an RJ48 cable, connect CN1 on the MDF card to the CSU (Figure
2-8). The following illustration shows CN1 pinouts.
Figure 2-7. RJ48 pinouts, CN1 connector
RJ48 Pin Designations
Pins
Designation
1 and 2
3 and 6
4 and 5
Receive from CSU
No connections
Transmit from the
DBS
7 and 8
Frame ground
Revised April 2000
DBS-EX23-530
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Procedures
Installing ISDN in a Double Cabinet with the ISDN in
the Slave
1. Before beginning ISDN installation, perform the “ISDN Function Reset”
command (FF1 9# 1# 1#). This command must be issued before the ISDN
can be installed properly.
2. Check SW4 on the SCC-B card. Be sure it is set to “Mode B.” (See Step 2
on page 2-14.)
4. Install an MDF card in the slave cabinet. (See Step 5 on page 2-17.)
5. Set Switch 1 on the ISDN card. (See Step 6 on page 2-18.)
6. Install an ISDN card in the “EC/TRK” slot of the slave cabinet.
7. Connect the Sync Cable from CN1 on the Sync Unit to CN5 on the ISDN
Note: Part Number VB-43564 is used for the Sync Cable when an ISDN
is installed only in the slave cabinet of a two-cabinet system.
8. At the slave cabinet, connect the cable attached to CN3 on the MDF card to
9. Using an RJ48 cable, connect CN1 of the MDF card to the CSU. (See
Figure 2-7 for RJ48 pinouts.)
10. At the slave cabinet, connect the ground cable on the MDF card as shown
Revised April 2000
DBS-EX23-530
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation Procedures
Installing ISDN in a Double Cabinet with ISDNs in the
Master and Slave
1. Before beginning ISDN installation, perform the “ISDN Function Reset”
command (FF1 9# 1# 1#). This command must be issued before the ISDN
can be installed properly.
2. Check SW4 on the SCC-B card. Be sure it is set to “Mode B.” (See Step 2
on page 2-14.)
4. Install an MDF card in each cabinet. (See Step 5 on page 2-17.)
6. Install an ISDN card in each “EC/TRK” slot.
7. Connect the Clock Sync Cable from CN4 on the master-cabinet ISDN to
CN5 on the slave-cabinet ISDN, as shown in Figure 2-10.
Note: Part Number VB-43564 is used for the Clock Sync Cable when
ISDNs are installed in the master and slave cabinets.
8. At the master cabinet, connect the Sync Cable from CN1 on the Sync Unit
to CN5 on the ISDN card (Figure 2-10).
9. At each cabinet, connect the cable attached to CN3 on the MDF card to
10. Using an RJ48 cable, connect CN1 of each MDF card to a CSU. (See
Figure 2-7 for RJ48 pinouts.)
11. For both cabinets, connect the ground cable from the MDF card as shown
Revised April 2000
DBS-EX23-530
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-10. Clock sync cable and sync cable connections, double-cabinet installation
MDF
Slave Cabine t
Slot Label
Connector
TRK1 TRK2 TRK3 EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC CPC AUX1 AUX2
Guide
CN3
SW1
CN4
Card
Label
MFR
2
DEC
I
MFR
1
CBL
(S)
DEC DEC DEC
DEC DEC
DEC DEC
TRK
S
D
N
N
O
T
CN5
TRK
U
S
E
D
MDF
Mas ter Cabinet
Slot Label
Connector
Interconnection
Cables
TRK1 TRK2 TRK3 EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/TRK SCC CPC AUX1 AUX2
Guide
Clock Sync.
Cable
(VB-43564)
CN3
SW1
CN4
Card
Label
I
S
CBL
(M)
DEC
DEC DEC
DEC DEC DEC
DEC DEC
SCC CPC
TRK
N
O
T
D
N
CN4
U
S
E
D
Note: The number of analog trunks that can be
installed depends on how many ISDN channels are
used.
Sync. Unit
CN1
Sync
Cable
CN5
2-24
DBS-EX22-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Quick-StartProgramming
The ISDN Interface includes many programming options, which allow you to
customize how your ISDN is used.
In most cases, however, you only need to set a few of the programs to get
your ISDN online. This chapter summarizes the programs that are essential to
ISDN installation.
The following table shows the topics that are described in this chapter. For
detailed descriptions of all the ISDN programs, see Chapter 4 -
“Programming Reference.”
Topic
Page
Revised April 2000
DBS-EX23-530
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Before You Begin
Before You Begin
Before you begin programming, you should be familiar with resetting the
DBS and performing the “ISDN Data Reset” command. The following
paragraphs explain when these two procedures are used.
The ISDN Data Reset command. If you are installing ISDN while you are
upgrading to a new DBS release, perform the “ISDN Data Reset” before you
begin ISDN programming.
Manually Resetting the DBS. Many of the ISDN programs require a manual
reset to take effect. Program all of the quick-start items first, then reset the
system by powering it off then back on.
Note:COP 1.07 or later is required on the PRI Card with CPC-EX 2.2 or later.
Revised April 2000
DBS-EX23-530
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Initial ISDN Options
Quick-Start Programming
Programming Initial ISDN Options
The following instructions explain the minimum programming required to
make the ISDN operational, plus the programming required for DID. Each
instruction includes a page number that references the relevant detailed
descriptions in Chapter 4. Default settings appear in bold.
Minimum Programming
Note:Option settings are in parenthesis ( ).
1. Set the system for ISDN operation.
Address
Options
FF1 2# 1# 44# (1)#
0= T1 Operation
1=ISDN Operation
2. If you are installing the ISDN while upgrading to a new DBS release,
perform the “ISDN Data Reset” command (page 4-28).
Note: DID settings are not maintained after the reset function.
Address
Options
FF1 9# 1# (1)#
0=No (retain settings)
1=Yes (clear settings)
3. Enter the system configuration (page 4-3).
Address
Options
FF1 9# 4# 1# 1# (0-8)#
0=DBS 40
1=DBS 72
2=DBS 96
3=DBS 40 + DBS 40 (ISDN must be in the slave cabinet.)
4=DBS 72 + DBS 40 (ISDN is not supported.)
5=DBS 72 + DBS 72 (ISDN must be in the slave cabinet.)
6=DBS 96 + DBS 40
7=DBS 96 + DBS 72
8=DBS 96 + DBS 96
3-4
DBS-EX22-530
Issued 10/23/98
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Programming Initial ISDN Options
Addresses
Options
Sync Source 1: FF1 9# 4# 1# 2# (1-3)#
Sync Source 2: FF1 9# 4# 1# 3# (0-3)#
Sync Source 3: FF1 9# 4# 1# 4# (0-3)#
Sync Source 1: 1=ISDN of the master cabinet
2=ISDN of the slave cabinet
3=Free run (internal clocking)
Sync Source 2: 0=None
1=ISDN of the master cabinet
2=ISDN of the slave cabinet
3=Free run (internal clocking)
Sync Source 3: 0=None
1=ISDN of the master cabinet
2=ISDN of the slave cabinet
3=Free run (internal clocking)
In most cases, set the sync sources as follows:
ISDN in a single cabinet or ISDN in a master cabinet:
Source 1=1 (ISDN of the master cabinet)
Source 2=3 (Free run)
Examples
Source 3=0 (None)
ISDN in a slave cabinet
Source 1=2 (ISDN of the slave cabinet)
Source 2=3 (Free run)
Source 3=0 (None)
ISDNs in the master and slave
Source 1=1 (ISDN of the master cabinet)
Source 2=2 (ISDN of the slave cabinet)
Source 3=3 (Free run)
5. Power the system OFF then ON.
Addresses
Options
Master cabinet: FF1 9# 4# 4# 1# 2# (0-23)#
Slave cabinet: FF1 9# 4# 5# 1# 2# (0-23)#
0-23 (0)
Revised April 2000
DBS-EX23-530
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Initial ISDN Options
Quick-Start Programming
7. Specify which trunk channels are used for ISDN (page 4-28).
Address
Options
FF2 (1-64)# 21# (5)#
0= Loop start
1=Ground start
2=DID
3=T1
4=CID
5=ISDN
Master Cabinet Setup
setting below options. Default setting are in BOLD.
8. Set up master span:
Address
Options
FF1 9# 4# 4# 5# 1# (0-1)# Network Type
0-Public
1-Private
Address
Options
FF1 9# 4# 4# 5# 2# (0-1)# Auto Progress
0-Disable
1-Enable
Address
Options
FF1 9# 4# 4# 5# 3# (0-2)# NSF
0-None
1-SDN
2-MegaCom
Address
Options
FF1 9# 4# 4# 5# 4# (0-3)# ISDN CO Type
0-4ESS
1-5ESS
2- Reserved
3- DMS100
3-6
DBS-EX22-530
Issued 10/23/98
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Programming Initial ISDN Options
Address
Options
FF1 9# 4# 4# 5# 5# (0-1)# ISDN International Dial Code
Deduction
0-Send as is
1-Deduct 011 from the code
Address
Options
FF1 9# 4# 4# 5# 6# (0-1)# ISDN Long Distance
Code“1”Deduction
0-Send as is
1-Deduct “1” from the code
Address
Options
FF1 9# 4# 4# 5# 7# (0-1)# ISDN Type and Plan Option
0-Determine Type and Plan
1-Always Type and Plan set to Unknown/Unknown
Slave Cabinet Set-Up
setting below options. Default setting are In BOLD
Special Installation for adding second cabinet. If you are adding a second
cabinet (slave) to an existing installation that has a Primary Rate span
configured, you must re-enter the configuration settings for the ISDN
channels in the Master cabinet. The re-dimensioning of the system to the new
double cabinet (master/slave) configuration causes the address of FF1 9# 4#
4# 1# 2# (0-23) to be reset to the default value of zero (0).
9. Set up slave span:
Address
Options
FF1 9# 4# 5# 5# 1# (0-1)# Network Type
0-Public
1-Private
Address
Options
FF1 9# 4# 5# 5# 2# (0-1)# Auto Progress
0-Disable
1-Enable
Revised April 2000
DBS-EX23-530
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Programming Initial ISDN Options
Address
Options
FF1 9# 4# 5# 5# 3# (0-2)# NSF
0-None
1-SDN
2-MegaCom
Address
Options
FF1 9# 4# 5# 5# 4# (0-3)# ISDN CO Type
0-4ESS
1-5ESS
2- Reserved
3- DMS100
Address
Options
FF1 9# 4# 5# 5# 5# (0-1)# ISDN International Dial Code
Deduction
0-Send as is
1-Deduct 011 from the code
Address
Options
FF1 9# 4# 5# 5# 6# (0-1)# ISDN Long Distance
Code“1”Deduction
0-Send as is
1-Deduct “1” from the code
Address
Options
FF1 9# 4# 5# 5# 7# (0-1)# ISDN Type and Plan Option
0-Determine Type and Plan
1-Always Type and Plan set to Unknown/Unknown
10. Program DIDs.
Address
FF1 9# 4# 6# (1-64)# 1# (0000-9999)#
11. Power the system OFF then ON.
Revised April 2000
DBS-EX23-530
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Programming Initial ISDN Options
12. Specify the extension number to call for each ISDN incoming DID
Address
FF1 9# 3# (0000-9999)# (100-699)#
13. Some ISDN lines provide Automatic Number Identification (ANI). This
service is similar to Caller ID by providing the number of the calling party.
For DID calls with ANI information provided, determine if ANI data or
DID data is displayed on the called telephone..
Address
Options
FF3 (Ext Port)# 54# (0-1)#
0=DID data on display
1=ANI data on display
14. If you need to program multiple extensions to ring with DIDs, go to the
If you do not need to program multiple DIDs, you are finished with initial
ISDN programming. Reset the DBS by turning it off then on again.
Multiple DID Programming
1. If you wish to assign the same DID number to more than one station,
Address
Options
FF1 2# 1# 32# (0-1)#
0=Off
1=On
2. Assign the ISDN DID numbers to stations (page 4-29).
Address
FF1 9# 3# (0000-9999)# (10-69 or 100-699)#
3. Reset the DBS by turning it off then on again.
Revised April 2000
DBS-EX23-530
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick-Start Programming
Programming Initial ISDN Options
Typical Central Office Configurations
Note:Unless stated all other default values are correct.
Lucent (AT&T) 4ESS
CO Type (0) 4ESS
NSF- None(0) or MegaCom(2) – Depends on service requested from CO.
ISDN international code deduct “011” - Set to (1) Deduct “011” from
being sent in Setup message to CO.
ISDN Long Distance “1”Code Deduction - Set to (1) Deduct “1” from
being sent in Setup message to CO.
Lucent (AT&T) 5ESS
CO Type (1) 5ESS
ISDN international code deduct “011” - Set to (1) Deduct “011” from
being sent in Setup message to CO.
Nortel (NT) DMS-100
CO Type (3) DMS100 This is the default setting.
Revised April 2000
DBS-EX23-530
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Programming Reference
This chapter describes programming parameters for the ISDN Interface.
The descriptions of each parameter include a list of available options and the
associated programming address. Default options appear in bold.
This chapter is intended for readers who are familiar with DBS programming.
For an introduction to DBS programming, see the Programming Guidance
Manual, Section 400.
The following table lists the topics described in this chapter.
Topic
Page
Revised April 2000
DBS-EX23-530
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
ISDN System Settings
ISDN System Settings
System Size
Parameter
System Configuration
Description
Identifies the system size.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming FF1 9# 4# 1# 1# (0-8)#
Options
0=DBS 40
1=DBS 72
2=DBS 96
3=DBS 40 + DBS 40 (ISDN must be in the slave cabinet.)
4=DBS 72 + DBS 40 (ISDN is not supported.)
5=DBS 72 + DBS 72 (ISDN must be in the slave cabinet.)
6=DBS 96 + DBS 40
7=DBS 96 + DBS 72
8=DBS 96 + DBS 96
T1/ISDN
Parameter
T1/ISDN
Description
Configures the system for either T1 or ISDN.
Programming FF1 2# 1# 44# (0-1)#
Options
0=T1
1=ISDN
Revised April 2000
DBS-EX23-530
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ISDN System Settings
Programming Reference
Clock Settings
Parameter
Sync Source 1
Description
The Sync Card (installed on the CPC-EX) provides a method of syn-
chronizing the DBS with the public network. This parameter deter-
mines the first clocking source for network synchronization. If the
first source fails, the system will switch to the second source. The
system will attempt to go back to the first source based on the value
The system considers a clock source to have failed when the slip
23 for instructions on setting the slip rate error counter.)
of typical sync source settings for single and double-cabinet sys-
tems.
Notes:
1. The “free run” setting is the only setting that can be entered for
more than one sync source.
2. For changes to this parameter to take effect, the system must be
powered down, then back up again.
Programming FF1 9# 4# 1# 2# (1-3)#
Options
1=ISDN of the master cabinet (synchronizes clocking with the pub-
lic network)
2=ISDN of the slave cabinet (synchronizes clocking with the public
network)
3=Free run (internal clocking)
4-4
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
ISDN System Settings
Parameter
Sync Source 2
Description
Determines the source of clocking for the second sync source. The
second sync source is used if the first sync source fails. The system
will attempt to switch from the second source back to the first
source based on the value entered under “Network Re-sync Timer”
If the second source fails and the first source is not working, the
system will switch to the third source.
In most cases, a system with one ISDN has the 2nd sync source set
to “3.” Systems with two Signs normally have the 2nd sync source
single and double-cabinet systems.
One of the three sync sources should be set to “3” (free run). A
free-run setting is needed, so the DBS ISDN can provide its own
clocking if the network clock fails.
(See “1st sync” for an introduction to clock synchronization.)
Notes:
1. The “free run” setting is the only setting that can be entered for
more than one sync source.
2. For changes to this parameter to take effect, the system must be
powered down, then back up again.
Programming FF1 9# 4# 1# 3# (0-3)#
Options
0=None
1=ISDN of the master cabinet (synchronizes clocking with the
public network)
2=ISDN of the slave cabinet (synchronizes clocking with the pub-
lic network)
3=Free run (internal clocking)
Revised April 2000
DBS-EX23-530
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
ISDN System Settings
Programming Reference
Parameter
Description
Sync Source 3
Determines the source of clocking for the third sync source. The
third sync source is used if both the first and second source fail.
The system will attempt to switch from the third source back to the
first source based on the value entered under “Network Re-sync
In most cases, a system with one ISDN has the 3rd sync source set
to “0.” Systems with two ISDNs normally have the 3rd sync source
single and double-cabinet systems.
One of the three sync sources should be set to “3” (free run). A
free-run setting is needed, so the DBS ISDN can provide its own
clocking if the network clock fails.
chronization.)
Notes:
1. The “free run” setting is the only setting that can be entered for
more than one sync source.
2. For changes to this parameter to take effect, the system must be
powered down, then back up again.
Programming FF1 9# 4# 1# 4# (0-3)#
Options
0=None
1=ISDN of the master cabinet (synchronizes clocking with the
public network)
2=ISDN of the slave cabinet (synchronizes clocking with the pub-
lic network)
3=Free run (internal clocking)
4-6
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
System-Wide Timers
System-Wide Timers
Parameter
Network Re-sync Timer
Description
If one clock source fails, the system will switch to another clock
source. The re-sync timer determines how often the system
attempts to return to the original clock source.
For example, if the first clock source (1st sync) fails, the system
switches to the second source. However, the system will try to
return to the first source based on the re-sync timer.
For instance, if the system changes to the second source at 12:00
p.m. and the re-sync timer is set for 24 hours, the DBS will attempt
to return to the first clock source at 12:00 p.m. every day. If the re-
sync timer is set for 1 hour, the DBS will attempt to return to the
first clock source every hour.
If the second source fails and the first source continues to be out-
of-service, the system switches to the third source. Again, the re-
sync timer determines how often the system will attempt to return
to the first source.
Note: When the system attempts to go back to the first clock
source, existing calls will be disconnected.
Programming FF1 9# 4# 2# 1# (0-25)#
Options
0-25
0=immediate (DBS returns to the first clock immediately.)
1-24=hours (Determines how often the DBS attempts to return to
the first clock.)
25=no retries (DBS does not attempt to go back to the first clock.)
Revised April 2000
DBS-EX23-530
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
System-Wide Timers
Programming Reference
Parameter
Description
Ringing Timer (T301)
Determines how long the called party will ring before the DBS will
disconnect the call.
Programming FF1 9# 4# 2# 2# (0-15)#
Options
0-10
0=180 sec.
1=20 sec.
2=40 sec.
3=60 sec.
.
.
.
11=220 sec.
12=240 sec.
13=240 sec.
14=240 sec.
15=Infinite
Parameter
Call Setup Timer (T303)
Description
Determines the time limit for a CO to respond to an outgoing call
attempt.
Programming FF1 9# 4# 2# 3# (0-10)#
Options
0-10
0=4 sec.
1=1 sec.
2=2 sec.
3=3 sec.
4=4 sec.
5=5 sec.
6=6 sec.
7=7 sec.
8=8 sec.
9=9 sec.
10=10 sec.
4-8
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
System-Wide Timers
Parameter
Disconnect Request Timer (AT&T) (T305)
Description
Determines the time allocated for the CO to disconnect a call
before the DBS disconnects the call.
Programming FF1 9# 4# 2# 4# (0-10)#
Options
0-10
0=4 sec.
1=1 sec.
2=2 sec.
3=3 sec.
4=4 sec.
5=5 sec.
6=6 sec.
7=7 sec.
8=8 sec.
9=9 sec.
10=10 sec.
Parameter
Disconnect Request Timer (NTI) (T305)
Description
Determines the time allocated for the CO to disconnect a call
before the DBS disconnects the call.
Programming FF1 9# 4# 2# 5# (0-10)#
Options
0-10
0=30 sec.
1=10 sec.
2=20 sec.
3=30 sec.
4=40 sec.
5=50 sec.
6=60 sec.
7=70 sec.
8=80 sec.
9=90 sec.
10=100 sec.
Revised April 2000
DBS-EX23-530
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
System-Wide Timers
Programming Reference
Parameter
Description
Release Request Timer (T308)
Determines the time allocated for the CO to acknowledge a discon-
nect/release.
Programming FF1 9# 4# 2# 6# (0-10)#
Options
0-10
0=4 sec.
1=1 sec.
2=2 sec.
3=3 sec.
4=4 sec.
5=5 sec.
6=6 sec.
7=7 sec.
8=8 sec.
9=9 sec.
10=10 sec.
Parameter
Outbound Call Processing Timer (T310)
Description
Determines the time allocated for the CO to deliver a call. If the
call is not delivered, the DBS will clear the call.
Programming FF1 9# 4# 2# 7# (0-15)#
Options
0-15
0=10 sec.
1=1 sec.
2=2 sec.
3=3 sec.
.
.
.
14=14 sec.
15=Infinite
4-10
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
System-Wide Timers
Parameter
Connect Request Timer (T313)
Description
Determines the time the DBS waits for the CO to acknowledge that
a call has been connected.
Programming FF1 9# 4# 2# 8# (0-15)#
Options
0-10
0=4 sec.
1=1 sec.
2=2 sec.
3=3 sec.
4=4 sec.
5=5 sec.
6=6 sec.
7=7 sec.
8=8 sec.
9=9 sec.
10=10 sec.
Revised April 2000
DBS-EX23-530
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Pad Settings
Programming Reference
Digital Pad Settings
Parameter
Digital Pad Settings
Description
Adjusts the volume of connections made via the ISDN. Default volume
levels are included for connections between different types of terminals
or circuits. For example, a K-TEL to ISDN connection may use one vol-
ume setting, while an SLT-to-ISDN connection may use another.
The volume settings are controlled by changing a pad number, which in
turn changes the loss or gain of the connection. In most cases, the default
pad settings do not need to be changed.
Programming
If the volume level of a connection is unsatisfactory, include the receiving
and sending circuit types in the command, then adjust the volume by assign-
circuit type. Pad numbers are defined in Figure 4-3 on page 4-13.
FF1 8# 4# 3# (1-12)# (1-12)# (0-30)#
Receiving
Circuit Type
(“To” Side)
Sending
Circuit Type
(“From” Side)
PAD No.
(Note: This uses the same address as T1 programming.)
Figure 4-1. Circuit-type numbers
Circuit Types
K-TEL
SLT
No.
1
2
3
DATA#
Analog CO Trk
ISDN Master
ISDN Slave
OPTION 1*
OPTION 2*
DTMF#
4
5
6
7
8
9
CONF (SCC)#
TONE1 (MFR1)#
TONE2 (MFR2)#
10
11
12
Notes:
#Circuit Types 3 and 9-12 are reserved for future use.
*Options 1 and 2 can be used to assign unique PAD levels to circuits that
require special volume levels. For example, if an OPX station needs a
higher volume level than other SLTs, the OPX station could be defined as
an “Option 1” circuit type.
4-12
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Digital Pad Settings
Options
Figure 4-2 shows the default values for the most common ISDN connec-
Figure 4-2. Default pad values
Figure 4-3. Pad Nos.
From
To
Setting
16
Value
-2 dB
-2 dB
-2 dB
-2 dB
-2 dB
-2 dB
-2 dB
-2 dB
Pad No.
Level
ISDN #1
ISDN #2
ISDN #1
ISDN #2
K-TEL
K-TEL
SLT
K-TEL
K-TEL
SLT
0
0 dB
16
1
+2 dB
16
.
.
SLT
16
.
.
ISDN #1
ISDN #2
ISDN #1
ISDN #2
16
.
.
16
14
15
16
17
.
+28 dB
+30 dB
-2 dB
-4 dB
.
16
SLT
16
Note: ISDN #1=master
ISDN #2=slave
.
.
.
.
29
30
-28 dB
-30 dB
Example
If calls to SLTs via a master ISDN have low volume levels, the PAD level for
connections from the master ISDN to all SLTs can be changed.
4-2 that the default pad value for setting 16 is -2 dB.
To raise the volume by 2 dB, you can change the pad value to 0. (As you can
The following example shows the programming required to change the value
to 0 dB:
FF1 8# 4# 3# 2# 5# 0#
Revised April 2000
DBS-EX23-530
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Pad Settings
Programming Reference
Extension Port Settings
Parameter
Station Port Class
Description
By default, DBS phones are assigned a circuit type, based on
whether they are KTELs or SLTs.
The circuit type is used with digital pad settings to determine the
loss/gain settings for connections to the ISDN. (See “Digital Pad
The Port Class parameter is provided in case a specific phone or
group of phones needs a unique pad level.
For example, an SLT is assigned by default as “circuit type 2.” How-
ever, if an SLT in a remote warehouse has inadequate volume levels,
the circuit type for the SLT could be changed to 7 (Option 1). Once
the SLT is changed to circuit type 7, the pad levels for circuit type 7
could be changed to provide the correct volume setting.
on page 4-12 for a definition of circuit types.
Programming FF3 (1-144)# 37# (1-2 or 7-8)#
Options This programming parameter will allow you to assign circuit types
1-12 to a station port. However, the only circuit types that should be
used with a station port are circuit types 1, 2, 7, or 8. (Circuit types 7
and 8 are used to assign unique PAD levels to circuits that require
special volume levels.)
4-14
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Digital Pad Settings
Trunk Port Settings
Parameter
Trunk Port Class
Description
By default, DBS trunks are assigned a circuit type, based on
whether they are analog or ISDN.
The circuit type is used with digital pad settings to determine the
loss/gain settings for connections to the ISDN. (See “Digital Pad
The Port Class parameter is provided in case a specific trunk or
group of trunks needs a unique pad level.
For example, an ISDN in a slave cabinet is assigned by default as
“circuit type 6.” However, if a specific ISDN trunk in a slave has
inadequate volume levels, the circuit type for the ISDN trunk port
could be changed to 8 (Option 2). Once the port number is changed
to circuit type 8, the pad levels for circuit type 8 could be changed
to provide the correct volume setting.
4-1 on page 4-12 for a definition of circuit types.
Programming FF2 (1-64)# 26# (5-8)#
Options
This programming parameter will allow you to assign circuit types
1-12 to a trunk port. However, the only circuit types that should be
used with a ISDN trunk port are circuit types 5 to 8. (Circuit types
7 and 8 are used to assign unique PAD levels to circuits that
require special volume levels.)
Revised April 2000
DBS-EX23-530
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Master and Slave Settings
Programming Reference
Master and Slave Settings
Trunk Configuration
Parameter
Number of ISDN Channels
Description
Determines how many ISDN channels are used.
Though each ISDN Interface provides 23 trunk channels, ISDN
trunks do not increase the overall trunk capacity of the DBS. Each
ISDN channel subtracts from the total number of analog trunks
that can be installed. The number of analog trunks that can be used
are always decremented in quantities of 1.
for possible ISDN and analog trunk channel combinations.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming Master cabinet: FF1 9# 4# 4# 1# 2# (0-23)#
Slave cabinet: FF1 9# 4# 5# 1# 2# (0-23)#
Options
0-23 (0)
Note: In most cases, ISDN channels are assigned in increments of
8.
Trunk Signaling
Parameter
Failure Mode
Description
Determines the way the system responds to alarms.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming Master cabinet: FF1 9# 4# 4# 1# 5# (0-1)#
Slave cabinet: FF1 9# 4# 5# 1# 5# (0-1)#
Options
0=Mode 1 (ISDN stays in operation even if errors are
detected.)
1=Mode 2 (ISDN shuts down if errors are detected.)
4-16
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Alarm Settings
Alarm Descriptions
ISDN alarms can be reported through LEDs on the ISDN card, an alarm relay
alarm settings for all three types of alarms.
Table 4-1. ISDN alarm definitions
Alarm
Description
Notification
Red
The DBS activates a red alarm when a loss of sig-
nal or out-of-frame condition lasts for more than
2.5 seconds.
FF key (after the counter is exceeded)
CFA LED on the ISDN card
Alarm relay on the ISDN MDF card
FF key (after the counter is exceeded)
YEL LED on the ISDN card
Alarm relay on the ISDN MDF card
Yellow
A yellow alarm is sent to the distant end of the
ISDN link to indicate that a red alarm has occurred.
If a red alarm occurs at the CO, the CO sends a yel-
low alarm to the DBS. If a red alarm occurs at the
DBS, the DBS sends a yellow alarm to the CO.
Frame
Loss
The DBS activates an OOF alarm when more than FF key (after the counter is exceeded)
one out of four consecutive framing bits is in error.
OOF LED on the ISDN card
CFA LED on the ISDN card
Alarm relay on the ISDN MDF card
Slip
The DBS activates a slip alarm when a data bit is
lost due to a frame misalignment. Frame misalign-
ment is caused by timing errors.
FF key (after the counter is exceeded)
OOF LED on the ISDN card
SLIP LED on the ISDN card (See
Note.)
Sync
Loss
The DBS activates a sync loss alarm due to timing FF key (after the counter is exceeded)
errors. Timing errors result in frame misalignment.
SLIP LED on the ISDN card
CFA LED on the ISDN card
AIS
The CO sends an AIS (Alarm Indication Signal) to AIS LED on the ISDN card
indicate an “out-of-service” condition on the net-
work side. The AIS, also referred to as the “keep
alive signal,” is comprised of all 1s and is
OOF LED on the ISDN card
CFA LED on the ISDN card
Alarm relay on the ISDN card
unframed. The DBS sends an AIS through the
Revised April 2000
DBS-EX23-530
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings
Programming Reference
Loss of
Signal
The DBS activates a loss of signal alarm when the FF key (after the counter is exceeded)
incoming ISDN signal is not received for more
than 150 ms.
CFA LED on the ISDN card
OOF LED on the ISDN card
Note: The LEDs on the ISDN card are normally steadily lit during an alarm condition. However, SLIP
alarms cause the SLIP LED to blink rather than light.
Table 4-2. Alarm-related programs
Parameter
Address
Function
Yellow Alarms
Yellow Alarm Send
Yellow Alarm Counter
Yellow Alarm Relay
FF1 9# 4# 4# 1# 7# (0-1)#
FF1 9# 4# 5# 1# 7# (0-1)#
Determines whether the DBS sends a yellow
alarm to the CO.
FF1 9# 4# 4# 3# 6# (0-9000)# Error counter for the Yellow Alarm FF key.
FF1 9# 4# 5# 3# 6# (0-9000)#
FF1 9# 4# 4# 4# 1# (0-1)#
FF1 9# 4# 5# 4# 1# (0-1)#
Determines if the alarm relay on the ISDN
MDF card closes in the event of yellow
alarms.
Red Alarms
Red Alarm Detection
FF1 9# 4# 4# 2# 1# (0-15)#
FF1 9# 4# 5# 2# 1# (0-15)#
The red alarm value is determined by network
requirements. This value should not be
changed.
When a red alarm occurs, the CFA LED on
the ISDN card lights, and the alarm relay on
the ISDN MDF card closes.
Red Alarm Recovery
FF1 9# 4# 4# 2# 2# (0-15)#
FF1 9# 4# 5# 2# 2# (0-15)#
Determines how long the DBS tries to recover
from a red alarm before it re-syncs the ISDN
trunk.
Red Alarm Counter
Red Alarm Relay
FF1 9# 4# 4# 3# 3# (0-9000)# Error counter for the Red Alarm FF key.
FF1 9# 4# 5# 3# 3# (0-9000)#
FF1 9# 4# 4# 4# 2# (0-1)#
FF1 9# 4# 5# 4# 2# (0-1)#
Determines if the alarm relay on the ISDN
MDF card closes in the event of red alarms.
Alarm Indication Signal
AIS Relay
FF1 9# 4# 4# 4# 5# (0-1)#
FF1 9# 4# 5# 4# 5# (0-1)#
Determines if the alarm relay on the ISDN
MDF card closes in the event of an alarm indi-
cation signal. An alarm indication signal is
comprised of all 1’s and is unframed.
Frame Loss Alarms
Frame Loss Counter
Frame Loss Relay
FF1 9# 4# 4# 3# 1# (0-9000)# Error counter for the Frame Loss FF key.
FF1 9# 4# 5# 3# 1# (0-9000)#
FF1 9# 4# 4# 4# 4# (0-1)#
FF1 9# 4# 5# 4# 4# (0-1)#
Determines if the alarm relay on the ISDN
MDF card closes in the event of frame loss
alarms.
4-18
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Parameter
Address
Function
Slip Alarms
Slip Counter
FF1 9# 4# 4# 3# 2# (0-9000)# Error counter for the Slip FF key.
FF1 9# 4# 5# 3# 2# (0-9000)#
Signal Loss Alarms
Loss of Signal Counter
FF1 9# 4# 4# 3# 4# (0-9000)# Error counter for the Signal Loss FF key.
FF1 9# 4# 5# 3# 4# (0-9000)#
Sync Loss Alarms
Sync Loss Counter
Sync Loss Relay
FF1 9# 4# 4# 3# 5# (0-9000)# Error counter for the Sync Loss FF key.
FF1 9# 4# 5# 3# 5# (0-9000)#
FF1 9# 4# 4# 4# 3# (0-1)#
FF1 9# 4# 5# 4# 3# (0-1)#
Determines if the alarm relay on the ISDN
MDF card closes in the event of sync loss
alarms.
Relay Control
Relay Reset
FF1 9# 4# 4# 4# 6# (0-1)#
FF1 9# 4# 5# 4# 6# (0-1)#
Determines whether the alarm relay is cleared
manually or automatically.
Revised April 2000
DBS-EX23-530
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings
Programming Reference
Alarm Transmission Options
Parameter
Yellow Alarm Send
Description
Determines whether the DBS sends a yellow alarm signal to the
CO.
Programming Master cabinet: FF1 9# 4# 4# 1# 7# (0-1)#
Slave cabinet: FF1 9# 4# 5# 1# 7# (0-1)#
Options
0=No
1=Yes
Parameter
Red Alarm Detection
Description
The default value for this parameter is determined by network
specifications. It should not be changed.
If a red alarm occurs, the “CFA” LED on the ISDN card lights.
the alarm relay on the ISDN MDF card closes.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming Master cabinet: FF1 9# 4# 4# 2#1# (0-5)#
Slave cabinet: FF1 9# 4# 5# 2# 1# (0-5)#
Options
Values
0-5
0=4
1=6
2=8
3=10
4=12
5=14
4-20
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Alarm Timers
Parameter
Red Alarm Recovery
Description
Determines how long the DBS tries to recover from a red alarm
before it re-syncs the ISDN trunk.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming Master cabinet: FF1 9# 4# 4# 2# 2# (0-15)#
Slave cabinet: FF1 9# 4# 5# 2# 2# (0-15)#
0-15
Options
Values
0=0 ms
8=80 ms
1=10 ms
2=20 ms
3=30 ms
4=40 ms
5=50 ms
6=60 ms
7=70 ms
9=90 ms
10=110 ms
11=120 ms
12=130 ms
13=140 ms
14=150 ms
15=160 ms
Revised April 2000
DBS-EX23-530
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings
Programming Reference
Error Counters for FF Alarm Keys
The following counters determine when FF alarm keys light.
FF alarm keys light when an error counter exceeds the specified number
within 24 hours. FF alarm keys can indicate the following types of alarms:
• Red alarms
• Loss of signal alarms
• Sync loss alarms
• Yellow alarms
• Slip alarms
• Frame loss alarms.
In most cases, the default values for the error counters do not need to be
changed.
The alarm keys can be assigned to any key telephone. However, the keys will
only work on a non-attendant phone that has the programming authorization
code (#98 9999) activated. With attendant phones, the keys work whether or
not the programming authorization code is activated.
For instructions on programming FF alarms keys, see page 4-35.
Note: Once the alarm condition is corrected, the FF alarm key will remain lit
until the end of the 24-hour period, unless you enter the “historical error
clearance” command. For a description of this command, see page 4-38.
Parameter
Frame Loss Counter
Description
Determines how many frame losses occur before a Frame Loss FF
key is lit.
The FF key lights when the counter exceeds the specified number
within a 24-hour period.
keys.)
Programming Master cabinet: FF1 9# 4# 4# 3# 1# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 1# (0-9000)#
Options
0-9000/24 hours (9000)
4-22
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Parameter
Slip Counter
Description
Determines how many slips occur before a Slip FF key is lit.
The FF key lights when the counter exceeds the specified number
within a 24-hour period.
This parameter also determines the number of slips that can occur
before the system switches to the next clock source. When the sys-
tem switches to the next clock source, the slip error counter for the
first clock source is reset.
Slips are losses of data bits due to framing errors.
Programming Master cabinet: FF1 9# 4# 4# 3# 2# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 2# (0-9000)#
Options
0-9000/24 hours (9000)
Parameter
Red Alarm Counter
Description
Determines how many red alarms occur before a Red Alarm FF
key is lit.
The FF key lights when the counter exceeds the specified number
within a 24-hour period.
Programming Master cabinet: FF1 9# 4# 4# 3# 3# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 3# (0-9000)#
Options
0-9000/24 hours (9000)
Revised April 2000
DBS-EX23-530
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings
Programming Reference
Parameter
Loss of Signal Counter
Description
Determines how many instances of loss of signal occur before a
Signal Loss FF key is lit.
The FF key lights when the counter exceeds the specified number
within a 24-hour period.
Programming Master cabinet: FF1 9# 4# 4# 3# 4# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 4# (0-9000)#
Options
0-9000/24 hours (9000)
Parameter
Sync Loss Counter
Description
Determines how many instances of sync loss occur before a Sync
Loss FF key is lit.
The FF key lights when the counter exceeds the specified number
within a 24-hour period.
Programming Master cabinet: FF1 9# 4# 4# 3# 5# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 5# (0-9000)#
Options
0-9000/24 hours (9000)
Parameter
Yellow Alarm Counter
Description
Determines how many yellow alarm indications occur before a
Yellow Alarm FF key is lit.
The FF key lights activated when the counter exceeds the specified
number within a 24-hour period.
Programming Master cabinet: FF1 9# 4# 4# 3# 6# (0-9000)#
Slave cabinet: FF1 9# 4# 5# 3# 6# (0-9000)#
Options
0-9000/24 hours (9000)
4-24
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Alarm Relay Controls
Parameter
Yellow Alarm Relay
Description
Determines whether the system closes the alarm relay on the ISDN
MDF card in the event of yellow alarms.
The alarm relay can be connected to an external alarm device such
as a buzzer. The external alarm device must be purchased sepa-
rately; it is not provided with the DBS ISDN.
yellow alarms occur before the relay closes.)
Programming Master cabinet: FF1 9# 4# 4# 4# 1# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 1# (0-1)#
Options
0=Off (Alarm relay does not close.)
1=On (Alarm relay closes.)
Parameter
Red Alarm Relay
Description
Determines whether the system closes the alarm relay on the ISDN
MDF card in the event of red alarms.
The alarm relay can be connected to an external alarm device such
as a buzzer. The external alarm device must be purchased sepa-
rately; it is not provided with the DBS ISDN.
A red alarm indicates a loss of frame (OOF) or loss of signal has
continued for over 2.5 seconds.
many red alarms occur before the relay closes.)
Programming Master cabinet: FF1 9# 4# 4# 4# 2# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 2# (0-1)#
Options
0=Off (Alarm relay does not close.)
1=On (Alarm relay closes.)
Revised April 2000
DBS-EX23-530
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings
Programming Reference
Parameter
Sync Loss Relay
Description
Determines whether the system closes the alarm relay on the ISDN
MDF card in the event of sync loss alarms.
The alarm relay can be connected to an external alarm device such
as a buzzer. The external alarm device must be purchased sepa-
rately; it is not provided with the DBS ISDN.
Sync-loss alarms result from clocking errors.
Programming Master cabinet: FF1 9# 4# 4# 4# 3# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 3# (0-1)#
Options
0=Off (Alarm relay does not close.)
1=On (Alarm relay closes.)
Parameter
Frame Loss Relay
Description
Determines whether the system closes the alarm relay on the ISDN
MDF card in the event of frame loss alarms.
The alarm relay can be connected to an external alarm device such
as a buzzer. The external alarm device must be purchased sepa-
rately; it is not provided with the DBS ISDN.
Programming Master cabinet: FF1 9# 4# 4# 4# 4# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 4# (0-1)#
Options
0=Off (Alarm relay does not close.)
1=On (Alarm relay closes.)
Parameter
AIS Relay
Description
Determines whether the system closes the alarm relay on the ISDN
MDF card in the event of alarm indication signals.
An alarm indication signal is comprised of all 1’s and is unframed.
The alarm relay can be connected to an external alarm device such
as a buzzer. The external alarm device must be purchased sepa-
rately; it is not provided with the DBS ISDN.
Programming Master cabinet: FF1 9# 4# 4# 4# 5# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 5# (0-1)#
Options
0=Off (Alarm relay does not close.)
1=On (Alarm relay closes.)
4-26
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Alarm Settings
Parameter
Relay Reset
Description
Determines whether the ISDN alarm relay is cleared (opened) auto-
matically or manually.
If cleared automatically, the relay is opened approximately one sec-
ond after the alarm condition ceases.
If cleared manually, the relay can be opened by entering the Alarm
Relay Clear code.
To enter the Alarm Relay Clear code, first enter the programming
authorization code (#98 9999), then enter one of the following
codes:
(Master cabinet: ON/OFF #94 8)
(Slave cabinet: ON/OFF #95 8)
Programming Master cabinet: FF1 9# 4# 4# 4# 6# (0-1)#
Slave cabinet: FF1 9# 4# 5# 4# 6# (0-1)#
Options
0=Auto
1=Manual
Revised April 2000
DBS-EX23-530
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Trunk Settings
Programming Reference
Trunk Settings
Parameter
Trunk Type
Description
Determines whether the trunk circuit is an analog loop start, analog
ground start, analog DID, T1, CID, or ISDN.
Note: For changes to this parameter to take effect, the system
must be powered down, then back up again.
Programming FF2 (1-64)# 21# (0-5)#
Options
0= Loop start
1=Ground start
2=DID
3=T1
4=CID
5=ISDN
Parameter
ISDN Data Reset
Description
Resets the ISDN settings stored in SRAM (Static Random Access
Memory). The reset restores these settings to default values.
Programming FF1 9# 1# (0-1)#
Note: If you enter a “1,” the following display appears:
CONFIRM
0: NO 1: YES
The purpose of this display is to make sure you want to reset the
data. Enter a 0 or 1, depending on whether you want to complete
or cancel the reset.
0=Do not reset
1=Reset
Options
0=No (retain settings)
1=Yes (clear settings)
4-28
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Trunk Settings
Parameter
Clear ISDN DID Assignments
Description
Removes all DID assignments for ISDN.
Programming FF1 9# 2# (0/1)#
Options
0 - Do not clear assignments
1 - Clear assignments
Parameter
Inbound ISDN DID Assignment
Description
Assigns an extension to each ISDN incoming DID number.
Programming FF1 9# 3# (0000-9999)# (100-699)#
Parameter
Default DID Assignments
Description
Assigns an extension to ring if no DID number is received on a
trunk port.
Programming FF1 9# 4# 6# (1-64)# 1# (0000-9999)#
Parameter
Calling Information
Description
Assigns a number to display for each trunk rung when no DID is
supplied.
Programming FF1 9# 4# 6# (1-64)# 2# (0000-9999)#
Note
If ANI is provided, the ANI information will display instead.
Parameter
Network Type
Description
Specifies the type of network connected to the ISDN span per mas-
ter cabinet or slave cabinet; either private network or public net-
work.
Programming FF1 9# 4# 4# 5# 1# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 1# (0-1)# (slave cabinet)
Options
0 - Public network
1 - Private network
Revised April 2000
DBS-EX23-530
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Trunk Settings
Programming Reference
Parameter
Auto Progress Setting
Description
Specifies whether progress messages are supplied by the DBS to
the ISDN span (master or slave cabinet).
Programming FF1 9# 4# 4# 5# 2# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 2# (0-1)# (slave cabinet)
Options
0 - Disable
1 - Enable
Parameter
Network Facility Setting
Description
Determines if a call is a Software Defined Network (SDN) call
(AT&T option) or general Megacom call.
Programming FF1 9# 4# 4# 5# 3# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 3# (0-1)# (slave cabinet)
Options
0 - None
1 - SDN
2 - Megacom
Parameter
ISDN CO Type
Description
Specifies the type of CO connected to the ISDN span.
Programming FF1 9# 4# 4# 5# 4# (0-3)# (master cabinet)
FF1 9# 4# 5# 5# 4# (0-3)# (slave cabinet)
Options
0 - 4ESS
1 - 5ESS
2 - Reserved
3 - DMS100
4-30
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Trunk Settings
Parameter
ISDN International Dial Code Deduction
Description
Specifies if the 011 is sent with an international call or if the 011 is
deleted.
Programming FF1 9# 4# 4# 5# 5# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 5# (0-1)# (slave cabinet)
0 - Send as is (with 011)
Options
1 - Do not send 011
Parameter
ISDN Long Distance Code “1” Deduction
Description
Specifies if the leading “1” is sent with a long distance call or if the
leading “1” is deleted.
Programming FF1 9# 4# 4# 5# 6# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 6# (0-1)# (slave cabinet)
0 - Send as is (with leading 1)
1 - Do not send leading 1
Options
Parameter
ISDN Type and Plan Option
Description
Specifies if the ISDN Type and Plan are determined or unknown.
Programming FF1 9# 4# 4# 5# 7# (0-1)# (master cabinet)
FF1 9# 4# 5# 5# 7# (0-1)# (slave cabinet)
0 - Determine Type and Plan
Options
1 - Always Type and Plan set to Unknown/Unknown
Revised April 2000
DBS-EX23-530
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Trunk Settings
Programming Reference
Parameter
ISDN DID Flexible Ringing Assignments
Description
This parameter enables or disables ringing for specific ISDN
Inbound DID numbers during Day, Night, Delayed Day and
Delayed Night modes.
Programming FF1 9# 5# (0000-9999)# (100-699)# (000000-111111)#
Options
0=Disable ringing
1=Enable ringing
Where the entry position determines the ringing as follows:
The default entry is 111000 (day and night ringing enabled,
delayed day and delayed night ringing disabled.
4-32
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Trunk Settings
Parameter
Multiple DID/DNIS
Description
This programming address controls two functions.
If only analog trunks are used, a “1” turns on multiple DID num-
bering. Multiple DID numbering allows the assignment of one
DID number to multiple extensions. If one DID number is
assigned to multiple stations, the stations ring simultaneously
when the DID number is dialed. More than one DID number can
be assigned to a single extension.
If ISDN trunks are used, a “1” also turns on multiple Inbound
ISDN DID numbering. Multiple Inbound DNIS numbering allows
the assignment of one ISDN DID number to multiple extensions.
If one ISDN DID number is assigned to multiple stations, the sta-
tions ring simultaneously when the DID number is dialed. More
than one DID number can be assigned to a single extension.
Up to 500 DID numbers can be assigned in each system; also, up to
500 Inbound ISDN DID numbers can be assigned. When Inbound
ISDN DID numbering is used, both the Inbound DID number table
and the DID table are used. See “Inbound ISDN DID Assignment”
Programming FF1 2# 1# 32# (0-1)#
Options
0=Off
1=On
Revised April 2000
DBS-EX23-530
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Extension Settings
Programming Reference
Extension Settings
Parameter
ANI Display Assignment
Description
Some ISDN lines provide Automatic Number Identification
(ANI). This service is similar to Caller ID by providing the
number of the calling party. For DID calls with ANI informa-
tion provided, this parameter determines if ANI number or
DID number is displayed on the called telephone.
Address
Options
FF3 (1-144)# 54# (0-1)#
0=DID data on display
1=ANI data on display
Notes
If the DID number called is not in the DID ring table, the call will
ring the default DID assignment (see below) and the ANI number
will display when the ANI information is provided. If no ANI infor-
mation is provided, the DID number is displayed.
4-34
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
FF Key Settings
FF Key Settings
Parameter
FF Alarm keys
Description This command dedicates FF keys for ISDN alarms. The FF key lights
when alarm occurrences exceed a specified number within a 24-hour
period.
The alarm keys can be assigned to any key telephone. However, the keys
will only work on a non-attendant phone that has the programming
authorization code (#98 9999) activated. With attendant phones, the keys
work whether or not the programming authorization code is activated.
Assignment Note: If you’re assigning an FF alarm to an FF key that is currently pro-
grammed, you must first clear the FF key before making a new assign-
ment.
Alarms from ISDN in the master cabinet:
ON/OFF PROG FFkey (101-107)# HOLD
Alarms from ISDN in the slave cabinet:
ON/OFF PROG FFkey (121-127)# HOLD
Options
Keys can be assigned for the following alarms:
• Red alarms
• Yellow alarms
• Sync loss
• Signal loss
• Frame loss
• Slips
The following table shows alarm key addresses. The addresses differ
depending on whether alarms are generated from the master or slave cab-
inet.
Alarm
Master ISDN Slave ISDN
Red
103#
107#
105#
104#
101#
102#
123#
127#
125#
124#
121#
122#
Yellow
Sync loss
Signal loss
Frame loss
Slips
Revised April 2000
DBS-EX23-530
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Special ISDN Function Codes
Programming Reference
Special ISDN Function Codes
The following function codes are used for troubleshooting and maintenance
of the ISDN Interface.
These codes can be entered remotely by dialing into the DBS and entering the
ISDN maintenance mode. To enter the ISDN maintenance mode, type an
uppercase “T” at the REMT prompt.
Parameter
Loopback 1
Description
Loopbacks provide diagnostic tests of the ISDN circuit or the
ISDN connection to the CO.
This loopback initiates a loopback with the CO. The loopback
takes place through the Line Build Out (LBO) chip on the ISDN
card.
This loopback is typically used to check the continuity between
the CO, CSU, MDF, and ISDN card.
Note: Before executing this loopback, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 0 (0 or 1)
Slave: ON/OFF #95 0 (0 or 1)
0=Off
1=On
Parameter
Loopback 2
Description
Loopbacks provide diagnostic tests of the ISDN circuit or the
ISDN connection to the CO.
This loopback also initiates a loopback with the CO. Loopback 2
is identical to Loopback 1, except that it loops back through the
Framer chip on the ISDN card, thereby testing more of the ISDN
circuitry.
Note: Before executing this loopback, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 1 (0 or 1)
Slave: ON/OFF #95 1 (0 or 1)
0=Off
1=On
4-36
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Reference
Special ISDN Function Codes
Parameter
Remote Loopback
Description
This command only applies to a DBS within a private network.
The command is entered at one DBS in order to loopback through
another DBS.
For example, to initiate a loopback from DBS “B” to DBS “A,”
this command would be entered at DBS “B.” In order for the loop-
back to work, DBS “A” must have the “Remote Loopback” option
turned on in system programming.
Notes:
1. The clock source of the DBS that issues this command must be
set to “free run.”
2. Before executing this command, you must first enter the pro-
gramming authorization code (#98 9999). This command only
applies to a DBS within a private network.
The command is entered at one DBS in order to loopback through
another DBS.
For example, to initiate a loopback from DBS “B” to DBS “A,”
this command would be entered at DBS “B.” In order for the loop-
back to work, DBS “A” must have the “Remote Loopback” option
Notes:
1. The clock source of the DBS that issues this command must be
set to “free run.”
2. Before executing this command, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 3 (0 or 1)
Slave: ON/OFF #95 3 (0 or 1)
0=Off
1=On
Parameter
AIS Signal Transmission
Description
Transmits an AIS signal (all 1s) to the CO.
Note: Before executing this code, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 4 (0 or 1)
Slave: ON/OFF #95 4 (0 or 1)
0=Off
1=On
Revised April 2000
DBS-EX23-530
4-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Special ISDN Function Codes
Programming Reference
Parameter
Forced Re-synchronization
Description
Re-synchronizes the DBS ISDN with the public network.
Notes:
1. Forced re-synchronization disconnects existing calls.
2. Before executing this code, you must first enter the program-
ming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 6
Slave: ON/OFF #95 6
None. Re-synchronization begins as soon as the code is entered.
Parameter
Historical Error Clearance
Description
Clears the error counters for the following alarms:
• yellow
• red
• framing loss
• slip rate
• loss of signal
• sync loss
Note: Before executing this code, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 7
Slave: ON/OFF #95 7
None. The counters are cleared as soon as the code is entered.
Parameter
Alarm Relay Clear
Description
Clears (opens) the alarm relay on the ISDN MDF card.
Note: Before executing this code, you must first enter the pro-
gramming authorization code (#98 9999).
Execution
Options
Master: ON/OFF #94 8
Slave: ON/OFF #95 8
None. The relay is cleared as soon as the code is entered.
4-38
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A CPC-EX 2.3 Updates
This Appendix describes the feature additions and software corrections for
the DBS phone system with CPC-EX Version 2.3. Note that not all features
described in this Appendix relate specifically to ISDN functionality, but
rather to the DBS CPC-EX overall system.
However, several of these updates do directly pertain to ISDN and should be
noted accordingly.
New Features
• Bus Monitor Time Print Change - Bus Monitor now prints the time
every one minute.
• Sixteen-Port Voice Mail/API Enhancement - In addition to the current
8-port API integration, this software change allows the DBS to support up
to sixteen-port API Integration.
• Off-Hook Voice Announce/API Enhancement - This feature provides
support of the DBS Off-Hook Voice Announce feature via the API.
• 44-Series Small LCD Key Telephone Soft Key Support (VB-44XXXX)
- This enhancement allows the Small Liquid Crystal Display (LCD) K-
TEL to use the softkeys when accessing the Voice Mail application.
• Call Record via API - This enhancement provides support for the Call
Record feature via the API.
Note: The following features, UNA Transfer, UNA Call Reversion,
Forwarding to UNA for CO Held Calls, All Ring Group, Private Password,
Additional RAI Access, and All Ring Group features have been fully tested in
our laboratory but not in live Beta trials. These features are to be considered
Beta-level features. If you have any difficulty with these new features please
call the BTSD Hotline in Secaucus, New Jersey, at (800) 822-0909.
*UNA Transfer - Adds the ability for a user, automated attendant, etc., to
transfer a call to Universal Night Answer (UNA) by dialing the access code
*78. The call may then be retrieved by dialing the UNA pickup code (78).
*UNA Call Reversion - Adds the ability for calls, that have reverted to the
attendant and are unanswered, to revert to UNA.
*Forwarding to UNA for CO Held Calls - An extension can be set so that
certain calls are forwarded to UNA. If an inside extension (such as an
automated attendant) receives a CO call, places the call on hold and dials the
forwarding extension, then the call will forward to UNA.
*All Ring Group - A call transferred to an “All Ring Group” rings all phones
in the group at the same time. This makes the call available to multiple
locations, including UNA, simultaneously.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
*Private Password - The private password feature allows a user to enter
programming and access to all programming parameters including the system
and remote passwords. The private password may always be used to enter the
system.
*Additional Remote Administration Interface (RAI) Access Method - In
addition to the existing RAI access, a new RAI access method has been
added. The RAI access allows an incoming call to be transferred to the RAI
(either manually or by Automated Attendant) and then the caller enters the
remote or private password.
ISDN Programming Flexibility - The existing ISDN programming has been
enhanced to allow programming flexibility in the following areas: Network
Type, Auto Progress, NSF, ISDN CO Type, ISDN International Dial Code
Deduction, ISDN Long Distance Code 1 Deduction, and ISDN Type and Plan
Option.
Software Corrections
SMDR Stopped Printing - In earlier versions, the SMDR output from the
DBS would stop printing and not reset. This problem has been corrected with
this version.
SMDR Header Printed More Often Than Every 60 Lines - In earlier
versions, the SMDR header printed more than every 60 lines. In this version,
the SMDR header now correctly prints out every 60 lines.
Last Digit of Voice Mail One Touch Key Was Truncated - In earlier
versions, if a Voice Mail One-Touch Access key was programmed when the
key was viewed with the Conf. Function, the last digit of the programmed
information could not be seen.
Previously Unable to restrict 800+ Numbers for TRS types 5 and 6 - In
the previous version if an 800-xxx number was entered in the special area and
special office code tables with the new North American Numbering Plan
(NANP) activated TRS types 5 and 6, it did not restrict the call. This problem
has been corrected in this version.
Override Toll Restriction with SSD Numbers Address Was Not
Available - In the previous version, the programming address FF1 2#1#4#
could not be accessed. The address is now available in this version.
DID Call to a Voice Mailbox Received Main Greeting - In the previous
version, in a Non-Integrated Digital PanaVOICE environment, if a DID/
DNIS call was directed directly to a voice mail box, the caller was sent to the
main greeting instead of the correct voice mail box. This problem has been
corrected with this version.
Page A-2
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Unusual First Ring on Incoming ISDN Calls - Previously incoming calls
on ISDN line had a long ringing pattern (6 seconds ON or more, then OFF).
This only occurred on the first ring. After the first ring, the ringing pattern
returned to normal. The ringing pattern for incoming ISDN calls now rings as
expected.
Calling Party Could be Heard Between Rings - In the previous version,
when an ISDN call was transferred, the station receiving the call could hear
the calling party between rings. This problem has been corrected in this
version.
Dial Tone Received After Placing Call - Previously, when placing an
outgoing call after dialing the number, the caller would receive another dial
tone. This problem has been corrected in this version.
ISDN Calls Disconnected - Previously if an ISDN-to-ISDN call was
attempted, and the called party was busy, instead of receiving CO Busy the
call was dropped. This problem has been corrected in this version.
16-Port Voice Mail Support via API
Description
This feature allows up to sixteen (16) voice mail ports via API integration.
Programming
The new programming for this enhancement consists of a continuation of the
existing programming of the current 8-port API set up. Previously for the 8-
port API the telephone type settings (FF3 (ext#)# 2# (telephone type)# ranged
from 41-48 for integrated VM. These values have been extended and they
now range from 41-56. See below:
From port 1-8FF3 (ExtPort)# 2# (41-48)#[Same as current]
From port 9-16
FF3 (ExtPort)# 2# (49-56)#[New]
Operation
N/A
Notes
• All additional voicemail programming must be completed on the entire 16
ports for the voice mail to function properly.
• Voice mail ports should be on consecutive AEC or DEC cards.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
Off-Hook Voice Announce (OHVA) via API
Description
This feature provides support of the DBS Off-Hook Voice Announce feature
via the API. This API feature addition allows applications that utilize API
integration with the DBS to have access to the OHVA feature.
Programming
No new programming is required.
Operation
N/A
Note
The OHVA feature via the API has the same feature limitations as listed in
the DBS manual.
Small LCD Soft Key Support via API
Description
This enhancement allows the 44-Series Small LCD Key-Telephone (VB-
44XXXX) K-TEL to use the softkeys when accessing the Voice Mail
application.
Programming
No new programming is required.
Operation
N/A
Note
The OHVA feature via the API has the same feature limitations as listed in
the DBS manual.
Page A-4
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Call Record (OHVA) via API
Description
This feature provides support of the DBS Call Record feature via the API.
This API feature addition allows applications that utilize API integration with
the DBS to have access to the Call Record feature.
Programming
No new programming is required.
Operation
N/A
Notes
• The Call Record feature via the API has the same feature limitations as
described for DBS CPC-EX ver. 2.1.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
Special Features
The following features marked with an “*”, UNA Transfer, UNA Call
Reversion, Forwarding to UNA for CO Held Calls, All Ring Group, Private
Password, Additional RAI Access, and All Ring Group features have been
fully tested in our laboratory but not in live Beta trials. These features are to
be considered as Beta-level features. If you have any difficulty with these new
features please call the BTSD Hotline in Secaucus, New Jersey, at (800) 822-
0909.
*UNA Transfer
Description
The UNA transfer feature allows a trunk call to be transferred to the UNA.
The call may be transferred manually or via a device such as an automated
attendant.
Programming
No programming is required for this feature.
Operation
To transfer a trunk call to UNA:
1. Hookflash or press HOLD to place the trunk call on hold.
2. Dial *78. After *78 is dialed, dial tone is heard indicating that the call has
successfully been transferred.
3. Hang up.
To answer a UNA call:
1. Go offhook.
2. Dial 78.
or
1. Directly pick up the UNA held trunk by pressing the dedicated trunk key.
Page A-6
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• When a call is transferred to UNA, the trunk caller hears the selected hold
sound source.
• When a call is transferred to UNA, the UNA continues to ring until the call
is answered (by dialing 78 or direct trunk access) or the caller hangs up.
• If multiple callers ring the UNA, the UNA calls are picked up on a first-in/
first-out method.
• The UNA cannot be a member of a hunt group.
• The UNA can be a member of an All Ring Group. (See “Forwarding to
UNA for CO Held Call”.)
*UNA Call Reversion
Description
The UNA call reversion feature allows calls that revert to the attendant (but
are unanswered) to revert to UNA.
Programming
Table A-1 UNA Call Revision Timer Values
Setting
Value
No reversion (default)
10 seconds
0
1
2
20 seconds
3
30 seconds
4
40 seconds
5
50 seconds
6
60 seconds
7
70 seconds
8
80 seconds
9
90 seconds
10
11
12
100 seconds
110 seconds
120 seconds
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
Operation
When the UNA Reversion Timer is set to 0, a call that reverts to the attendant
and is not answered, continues to ring at the attendant. It does not revert to
UNA. When the UNA Reversion Timer is set to a value other than 0, a call
that reverts to the attendant and is not answered within the specified time
reverts to UNA.
To answer a UNA call:
1. Go off-hook.
2. Dial 78.
or
1. Directly pick up the trunk by pressing the dedicated trunk key.
Notes
• When a call reverts to UNA, the UNA will continue to ring until the call is
answered (by dialing 78 or by direct trunk access) or the caller hangs up.
• If multiple callers ring the UNA, the UNA calls are picked up on a first-in/
first-out method.
• The Call Reversion Timer must be set to “revert calls to the attendant”
position for unanswered calls to then be reverted to UNA.
*Forwarding to UNA for CO Held Call
Description
An extension can forward certain calls to UNA. If an inside extension (such
as an automated attendant) receives a CO call, it places the CO call on hold
and dials the forwarding extension. Then, the call will forward to UNA.
Internal calls, direct calls to the forwarding extension, or T1 network calls
ring the extension. They do not forward to UNA.
This feature is particularly useful in a situation when calls come into an
automated attendant and then, on caller selection, may transfer to an
extension such as the attendant. When the extension user goes on break etc.,
the calls can be forwarded to UNA to ensure that the call is handled.
Page A-8
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
No new programming required. However, the Class of Service for the
forwarding station must allow Call Forwarding to be Set/Reset for this feature
to operate.
Operation
To set UNA forwarding:
1. At the forwarding extension, go off-hook or press ON/OFF.
2. Dial 725.
3. Hang up or press ON/OFF.
To cancel UNA forwarding:
1. At the forwarding extension, go off-hook or press ON/OFF.
2. Dial 72.
3. Hang up or press ON/OFF.
To transfer a CO call to an UNA forwarding extension:
1. Place the CO call on hold by pressing the HOLD key or by hookflashing.
2. Dial the UNA forwarding extension. The call immediately forwards, you
hear dial tone and the display reads FWD UNA.
3. Hang up or press ON/OFF.
Notes
• When a call rings UNA, the UNA will continue to ring until the call is
answered (by dialing 78 or by direct trunk access) or the caller hangs up.
• If multiple callers ring the UNA, the UNA calls are picked up on a first-in/
first-out method.
• Internal calls, direct calls to the forwarding extension, or T1 network calls
ring the extension. They do not forward to UNA.
• A DISA caller will not be forwarded to UNA, but will ring the forwarding
extension.
• The held CO will hear the call hold tone until the call is answered.
• If permanent call forwarding is also set in the forwarding extension, CO
held calls will forward to UNA. However, all other calls will follow the
permanent call forwarding.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
• An extension user can only set “Do Not Disturb” or one type of call
forwarding at a time including call forwarding to UNA. When the user sets
DND or a call forwarding type, the previously set DND or call forwarding
type is cleared.
• Call forward to UNA cannot be assigned to an FF-Key.
*All Ring Group
Description
A new type of ringing group has been added - the All Ring Group. A call
transferred to an All Ring Group rings all key telephones in the group at the
same time. This makes the call available to multiple locations simultaneously.
Once the call is answered, all other key telephones in the group stop ringing.
A common use for this feature is to have an Automated Attendant transfer a
CO call to an All Ring Group on a selected input by the caller.
Up to four (4) All Ring Groups may be assigned. Up to 16 key telephone
members may be in each group. In addition to the 16 key telephone members,
the UNA may also be assigned to an All Ring Group.
Programming
The All Ring Group feature utilizes existing Multiple DID Ringing to set up
the All Ring Group. All members of the All Ring Group are set in standard
DID programming (FF1 8# 3# (DID No.)# (Ext. No.)#. However, since calls
cannot be transferred to a DID number, an All Ring Group Pilot number is
first established and this pilot number is then linked to a DID number. In
total, four programming addresses must be set for the All Ring Group feature
to operate. These include:
Operation
To transfer a CO call to an All Ring Group:
1. Place the call on hold by pressing HOLD (key telephone) or flashing the
hookswitch (SLT).
2. Dial the All Ring Group Pilot Number. After the call is transferred to the
All Ring Group, dial tone is heard.
Page A-10
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
When a call is transferred to the All Ring Group, every phone in the All Ring
Group rings. When any phone in the group is answered, all phones stop
ringing.
Notes
• The All Ring Group may include the UNA (780).
• The original call must be a CO call. An internal call cannot be transferred
to an All Ring Group. If you attempt to transfer an internal call to an All
Ring Group, you will receive busy tone.
• A call presented to an All Ring Group will not recall or revert. The call
must be answered or the caller must hang up.
• All Ring Groups cannot be chained together. In other words, an All Ring
Group Pilot Number cannot be assigned as a member of another All Ring
Group.
• Extensions may be a member of multiple All Ring Groups.
• If the DBS is part of a networked system, the All Ring Group members
must be extensions on the local node.
• Only one call at a time may ring at a key telephone if non-appearing (lights
the EXT LED).
*Private Password
Description
A new private password has been added to allow entry into system
programming at any time. This is useful if the normal system and/or remote
password is forgotten, lost, mis-entered, or intentionally changed by an
unauthorized person.
SPECIAL NOTICE: The private password should be changed from the
default setting after system installation, recorded and kept confidential by the
system manager.
SPECIAL NOTICE: The system must be entered using the private password
to view the private password programming address.
Programming
Programming Address
FF1 6# 3# [NNNN]#
Default Password: 6789
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
Notes
• You must enter programming using the private password to view the
private password address. The private password address will not appear
and is not accessible if programming is entered using the system or remote
password.
• If the system or remote password is set to the same value as the private
password, then the private password address will not be accessible. You
must first change the system or remote password to another value and then
log in again using the private password to have access to the private
password address.
• If you are at an attendant key telephone when entering programming, you
must first enter #98 followed by the 4-digit private password before
entering programming (see below). Otherwise, the private password is not
accessible.
Operation
To access the system using the private password at any display key telephone
(including an attendant telephone):
1. Go off-hook or press ON/OFF key.
2. Dial #98 followed by the 4-digit private password.
3. Press PROG followed by ##.
4. To exit system programming, hang up or press the ON/OFF key.
Terminal Programming Through a Direct Connection
When programming from a terminal connected to the RS-232C (SMDR) port,
perform the following steps:
1. Make certain the cables are configured and connected as outlined in
Section 300.
2. Make certain the DBS is in the SMDR mode by entering the following
code from the attendant port:
ON/OFF #93
3. Enter your terminal communications program and make sure your PC's
data communications settings match those of the DBS.
4. From your terminal communications program, type the following
command:
Page A-12
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
#99xxxx (where xxxx = the site's private password)
5. After the DBS responds, type P and then press Enter.
6. Follow the directions on the screen to access the desired program. (See
“Terminal Programming Commands.”)
Terminal Programming Through DISA
Note: The DBS must be equipped with an MFR card and an RAI card to
allow terminal programming using this method.
When programming through a DISA trunk, perform the following steps:
1. Dial into the DBS through a DISA trunk.
2. Once you are connected, type #6 followed by the private password from
your terminal communications program.
3. After the DBS responds with REMT>, type P and then press Enter.
4. Follow the directions on the screen to access the desired program. (See
“Terminal Programming Commands.”)
Terminal Programming Through a CO Trunk and Operator Transfer
Note: The DBS must be equipped with an MFR card and an RAI card to
allow terminal programming using this method.
SPECIAL NOTICE: If you use the following method, the private password
must be given to the attendant. Use the new RAI access method instead. (See
“Additional RAI Access Method”)
When programming through a normal trunk, perform the following steps:
1. Dial into the DBS through a normal trunk.
2. Ask the operator to place you on hold and dial #6 followed by the private
password to transfer you into remote programming.
3. After the DBS responds with REMT>, type P and then press Enter.
4. Follow the directions on the screen to access the desired program. (See
“Terminal Programming Commands.”)
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
Terminal Programming Through Additional RAI Access Method
(See “Additional RAI Access Method”.)
Terminal Programming Commands
Use the following commands to navigate terminal programming:
Command
~01
~02
~03
~04
~05
~06
~07
~08
~09
~10
~B
Description
Access System parameters
Access Trunk parameters
Access Extension parameters
Access Ring assignments
Access FF-key assignments
Access Name assignments
Access Toll Restriction data
Access Least Cost Routing data
Access Copy mode
Access Speed Dial data
Back to previous address
Back to previous port
~b
~F
Forward to next address
Forward to next port
~f
~R
Return to provide mode
Quit
~Ctrl-Z
*Additional RAI Access Method
Description
In addition to the existing RAI access method, a new RAI access method has
been added. A new access code, #97****, has been added to the DBS. When
this code is dialed, a held call is transferred to the RAI modem. The system
then sends a <PASSWORD> prompt and the remote or private password
must be entered to connect to terminal programming. This allows more
security for passwords since the password does not have to be used by the
transferring person or device.
Page A-14
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
No additional programming is required for the DBS. However, if an
automated attendant or other device performs the transfer, the automated
attendant or other device must be set up to transfer your call by dialing
#97****.
Operation
To access the system using the new RAI Access method:
Note: The following procedure uses a preprogrammed automated attendant to
transfer a call to the RAI.
1. At the PC terminal program, dial into the DBS through a normal trunk.
2. Follow the appropriate method to transfer to the RAI modem.
Normally, an automated attendant will be configured to answer your call,
play a message prompting a response (dial 1 to access Sales, 2 to ...etc.)
where one of the responses will place you on hold and dial the #97****
access code to reach the RAI.
3. Wait a few seconds for the RAI modem to return the modem tone and for
your terminal program to connect.
4. If Password> is not displayed, press the Enter key.
5. When Password> is displayed, dial the 4-digit remote or private password.
6. After the DBS responds with REMT>, type P and then press Enter.
7. Follow the directions on the screen to access the desired program. (See
“Terminal Programming Commands”.)
Note: The following procedure has the attendant manually transfer a call to
the RAI.
1. Start your PC terminal program.
2. With a telephone connected to the modem, manually dial into the DBS
through a normal trunk.
3. When the attendant answers, ask the attendant to dial #97**** to transfer
your call to the RAI modem.
4. When you hear modem tone, enable your terminal program to connect
(usually be selecting Connect).
5. If after a few seconds Password> is not displayed, press the Enter key.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
6. When Password> is displayed, type the 4-digit remote or private
password.
7. After the DBS responds with REMT>, type P and then press Enter.
8. Follow the directions on the screen to access the desired program. (See
“Terminal Programming Commands”.)
ISDN Programming Flexibility
Description
The previous versions did not allow the programming flexibility to
accommodate certain central office ISDN configurations. This enhancement
allows the flexibility in programming to set the DBS parameters to match
certain central office provisioning.
Programming
The following programming addresses are no longer valid:
Name
Key Sequence
ISDN CO Type
(0-3)
Network Type
Auto Progress
(1-64)
(1-64)
(1-64)
(0-1)
(0-1)
(0-1)
SDN/MEGACOM
ISDN Upgrade Procedure:
1. New COP 1.07A is required on Primary Rate card(s).
2. Set system for ISDN function:
(1)
Page A-16
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Perform ISDN reset function:
(1)
Note: DID settings are not maintained after reset function.
4. Set system configuration:
1
(0-8)
5. Set the clock synchronization sources:
Sync Source 1:
(1-3)
Sync Source 2:
(1-3)
(1-3)
Sync Source 3:
6. Cycle the unit's power switch.
7. Configure number of “B” channels per cabinet:
Master:
(0-23)
Slave:
(0-23)
8. Set trunk type per channel for ISDN:
(trunk number)
(5)
Master Cabinet Set-Up:
Refer to “Typical Central Office Configurations” for setting the following
options. Default settings are bold.
Set up master span:
(0-1) Network Type
0-Public
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
1-Private
(0-1) Auto Progress
0-Disable
1-Enable
(0-2) NSF
0-None
1-SDN
2-MegaCom
(0-3) ISDN CO Type
0-4ESS
1-5ESS
2- Reserved
3- DMS100
(0-1) ISDN International
Dial Code Deduction
0-Send as is
1-Deduct 0 1 1 from the code:
(0-1) ISDN Long Distance Code
0-Send as is
1-Deduct 1 from the code
(0-1) ISDN Type and Plan Option
0-Determine Type and Plan
1-Type and Plan always set to Unknown/Unknown
Page A-18
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Slave Cabinet Set-Up
Refer to “Typical Central Office Configurations” for setting the following
options. Default settings are bold.
Note: Observe the following Special Installation Note when adding a second
cabinet:
If you are adding a second cabinet (slave) to an existing installation that has a
Primary Rate span configured, you must re-database the number of ISDN
channels in the Master cabinet. The re-dimensioning of the system to the new
double cabinet (master/slave) configuration
causes
(0-23) to be reset to the default value of zero (0).
Set up Slave Span
(0-1) Network Type
0-Public
1-Private
(0-1) Auto Progress
0-Disable
1-Enable
(0-2) NSF
0-None
1-SDN
2-MegaCom
(0-3) - ISDN CO Type
0- 4ESS
1- 5ESS
2- Reserved
3- DMS-100
(0-1) ISDN International
Dial Code Deduction
0-Send as is
1-Deduct 0 1 1 from the code
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
(0-1) ISDN Long Distance Code Deduction
0-Send as is
1-Deduct 1 from the code
(0-1) ISDN Type and Plan
Option
0-Determine Type and Plan
1-Type and Plan always set to Unknown/Unknown
Reprogram the DIDs:
(1-64)
(0000-9999)
Turn the power switch OFF, and then back ON again
Operation
N/A
Notes
UNLESS STATED ALL OTHER DEFAULT VALUES ARE CORRECT.
Typical Central Office Configurations
Lucent (AT&T) 4ESS
• CO Type (0) 4ESS
• NSF- None (0) or MegaCom (2) - Depends on service requested from CO.
• ISDN International Code Deduct 0 1 1
-
Set to (1) to deduct 0 1 1 from the CO Setup message.
• ISDN Long Distance 1 Code Deduction
• Set to (1) to deduct 1 from the CO Setup message.
Lucent (AT&T) 5ESS
• CO Type (1) 5ESS
Page A-20
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
-
-
ISDN International Code Deduct 0 1 1
Set to (1) to deduct 0 1 1 from the CO Setup message.
Nortel (NT) DMS100
CO Type (3) DMS100 (This is the default setting.)
The ISDN PRI provides a flexible method of providing access to the Public
Switched Telephone Network (PSTN). Because of the many ways that the CO
can configure an ISDN span, it is essential that the DBS configuration and
the provisioning of the CO are compatible. The following tables identify the
critical parameters that must be set for proper operation. These tables also
provide a list of information that must be gathered on the CO, as well as the
type of information that the CO needs to know about the DBS system.
#
Info Needed from CO
Comments (examples)
1
Manufacture of CO and
software load
5E11 (5ESS with load 11), DMS-100 with NA008
2
3
Is local dialing 7 digits, 10
digits or a combination?
For long distance dialing,
does the CO want to see the
leading 1 ?
-
-
-
, or
-
-
4
For international dialing,
does the CO want to see the
leading 0 1 1 ?
0 1 1 -(15-digit number) or (15-digit number)
#
1
2
3
Typical Info for CO
Installation Address
Comments (examples)
Is this a new installation?
Extended wiring beyond
phone room?
4
5
Main phone number of
installation
Contact person for installa-
tion
Contact for order informa-
tion
6
7
Billing name
Billing address
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
#
Typical Info for CO
Comments (examples)
8
Long distance Carrier
InterLATA (PIC)
Identifies the carrier who will provide long
distance access.
9
Long distance Carrier
(IntraLATA) (LPIC)
Identifies the carrier who provides access for con-
nections that are not local but are still within the
local LATA.
1
0
Request date of installation
Facility type
1
1
ISDN PRI
1
2
Facility quantity
1 or 2 spans
NOTE: The following items must be provided on a per span basis.
1
3
Signaling code
DS-1 (1.544 Mbps)
1
4
Line coding
B8ZS (Binary 8 Zero Substitution)
ESF (Extended Superframe)
Voice or Voice/Data
1
5
Framing Format
Bearer configuration
1
6
1
7
Quantity of B (bearer)
channels
23B + 1D - Max. setting (must have 1 D channel)
Or XB + 1D where X is 1-23 for a fractional span
1
8
Call type
Two Way
1
9
Quantity of phone numbers A block of 20 numbers is generally assigned.
Note: With DID, the total number of telephones
will exceed the total number of B channels.
2
0
Number of incoming digits Select 4 digits. Used with DID
to CPE (Customer Premise
Equipment - DBS)
2
1
ISDN PRI Protocol
Glare Resolution
5ESS Custom, DMS-100 Custom (NTNAPRI) or
4ESS
2
2
CPE yield to CO
2
3
Channel selection used by
CO
High-to-Low B-channel selection
Page A-22
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
#
Typical Info for CO
Comments (examples)
2
4
Source of Calling Party
Number
The CO must source the Calling Party Number.
2
5
Service Options
ANI - Automatic Numbering Indication
Hunt group -
MegaCom -only for 4ESS operation
Note: If two spans are implemented, each span has a separate D channel (D
channel sharing is NOT permitted).
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. CPC-EX 2.3 Feature Update
Section 530-ISDN Ref.
CPC-EX Version 2.3.2
This section contains the CPC-EX Version 2.32 updates for the Panasonic
DBS Digital Business System. It provides a description of each of the
changes made to the Panasonic DBS Digital Business System software and
hardware included in the system.
Affected Items
The following hardware and software is affected:
VB-43415 with CPC-EX/BPU
VB-43415/A with CPC-EX/NPU
Feature Changes
Summary
• Transfer Ringing heard During External Call Forward - No Answer on
ISDN
• Station Message Detail Recording (SMDR) not Printing Long Distance
Calls
• Caller-ID Automatic Number Identification (ANI) is not Sent to the
Applications Programming Interface (API) when the Incoming Trunk is
ISDN
• SLTA Repeating Digits
• Call Forward Outside Call was Recalled After Recall Timer expired
• System Speed Bins 257-500 Unavailable
Change Details
Transfer Ringing heard During External Call Forward - No Answer on
ISDN
In the previous versions, if an incoming ISDN call was transferred to a station
that was Call Forward Outside, the called party only heard transfer ringing
when the outgoing call from the call forwarded station was answered. The
calling party heard talking and transfer ringing. This problem is fixed in
version 2.32
Programming Considerations
None
Page A-24
DBS Manual - Revised April 2000
DBS-2.3-400
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 530-ISDN Ref.
Appendix A. CPC-EX 2.3 Feature Update
Station Message Detail Recording (SMDR) not Printing Long Distance
Calls
Previously if FF1 2# 2# 7# was set for long distance only, when a long
distance call was placed, it was not recorded by SMDR. SMDR now correctly
prints out long distance calls.
Programming Considerations
FF1 2# 2# 7#
Caller-ID Automatic Number Identification (ANI) is not Sent to the
Applications Programming Interface (API) when the Incoming Trunk is
ISDN
In previous versions, Caller-ID (ANI) information was not sent to the API
when the incoming trunk was ISDN. In this release, the Caller-ID (ANI)
information is sent to the API.
Programming Considerations
None
SLTA Repeating Digits
Repeating digits were sent when an SLTA was used on a T1 circuit to call
another T1-Network node, or to call out of another T1 node to a CO. If an
SLTA was used, to call on a T1 circuit, to another node or out of another node
to a CO trunk, once the call was established, if digits were sent from the
SLTA, the digits would be repeated.
Example: If you dial 12345 from an SLT, the called party receives
1122334455)
This problem is corrected with this release.
Programming Considerations
None
Call Forward Outside Call was Recalled After Recall Timer expired
Previously, if an incoming call was transferred from Station A to Station B
(which was set for Call Forward Outside), the following events occurred--
when Station A's Call Forward No Answer Timer expired (after the call was
established with an outside CO), the outside connection was terminated, and
the call was recalled to Station A. This problem is resolved in this version.
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 530-ISDN Ref.
Appendix A. CPC-EX 2.3 Feature Update
Programming Considerations
None
System Speed Bins 257- 500 Unavailable
Previously, if a System Speed Dial (SSD) number of 257 or greater was used,
System Speed Dial numbers 001 through 256 were reprogrammed. System
Speed Dial Bins 257 - 500 are now available.
Programming Considerations
None
DBS-2.3-400
DBS Manual - Revised April 2000
Page A-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Error counters
frame loss 4-22
A
AIS alarm
frame loss counter 4-22
loss of signal 4-24
red alarms 4-23
slips 4-23
sync loss 4-24
definition 4-17
relay 4-26
transmission from the DBS 4-37
Alarm indication signal (see AIS)
Alarm relay clear 4-38
Alarm relays
sync loss counter 4-24
yellow alarms 4-24
ESF (see extended superframe)
Extended superframe format
description 1-3
AIS 4-26
alarm relay clear 4-38
frame loss 4-26
red alarms 4-25
relay reset 4-27
sync loss 4-26
F
yellow alarms 4-25
Alarm summary 4-17
Alarm timers
yellow alarm detection 4-21
Alarm transmission
red alarm detection 4-20
yellow alarms 4-20
Auto failure mode 4-16
Failure mode 4-16
FF alarm keys 4-35
Forced re-synchronization 4-38
Fractional ISDN 2-4
Frame format
description 1-3
Frame loss alarm
counter 4-22
definition 4-17
relay 4-26
B
Frame loss counter 4-22
Blue alarm (see AIS)
G
C
Grounding 2-20
Channel 1-9
Channel numbers 4-16
Channel service unit
distance from DBS 2-18
installing 2-12
specifications 1-9
Clock settings
H
Hardware requirements 1-8, 2-3
Historical error clearance 4-38
I
definitions 4-4
ISDN Data Reset 2-14, 2-21, 2-23, 3-3, 4-28
quick-start instructions 3-5
Clock source 1 4-4
Clock source 2 4-5
Clock source 3 4-6
Clock sync cable 2-23
CSU (see channel service unit)
K
Keep alive signal (see AIS)
L
Loopbacks
loopback 1 4-36
loopback 2 4-36
remote loopback 4-37
Loss of signal alarm
counter 4-24
definition 4-18
Loss of signal counter 4-24
D
DID Programming
Multiple 3-9
E
Error clearance 4-38
Revised April 2000
DBS-EX23-530
Index-i
Download from Www.Somanuals.com. All Manuals Search And Download.
Sync source 3 4-6
Sync unit 2-15
System settings
clock settings 4-4
system size 4-3
System size 4-3
System-wide timers
M
Manual failure mode 4-16
Master and slave settings
number of ISDN channels 4-16
trunk configuration 4-16
MDF card 1-8, 2-17
Multiple DID Programming 3-9
network re-sync timer 4-7, 4-8, 4-9, 4-10, 4-11
N
T
Network re-sync timer 4-7, 4-8, 4-9, 4-10, 4-11
Trunk assignments for double-cabinet systems 2-6
Trunk assignments for single-cabinet systems 2-5
Trunk configuration 4-16
Trunk numbering
double-cabinet systems 2-6
single-cabinet systems 2-5
Trunk port class 4-15
Number of ISDN channels 4-16
O
Ordering ISDN services 1-4
P
Port class 4-14, 4-15
Trunk settings
multiple DID/DNIS 4-33
trunk type 4-28, 4-29, 4-30, 4-31, 4-32
Trunk signaling
failure mode 4-16
Trunk type 4-28, 4-29, 4-30, 4-31, 4-32
R
Red alarm
counter 4-23
definition 4-17
detection 4-20
relay 4-25
V
Red alarm counter 4-23
Red alarm relay 4-25
Relay reset 4-27
VB-43110 1-8
VB-43562 1-8
VB-43563 1-8, 2-15
VB-43564 1-8, 2-21
VB-43571 1-8
Remote loopback 4-37
Remote programming 4-36
Resetting the DBS 3-3
Re-sync timer 4-7, 4-8, 4-9, 4-10, 4-11
RJ48 pinouts 2-19
Y
Yellow alarm
counter 4-24
definition 4-17
detection 4-21
relay 4-25
S
SCC
switch 4 2-15
Slip alarm
counter 4-23
definition 4-17
Station port class 4-14
Sync cable 2-18, 2-21, 2-23
Sync loss alarm
counter 4-24
definition 4-17
relay 4-26
Sync loss counter 4-24
Sync source 1 4-4
Sync source 2 4-5
Index-ii
DBS-EX23-530
Revised April 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|