Always there to help you
Register your product and get support at
AECS7000
Question?
Contact
Philips
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Important
2
Important safety information
Notice
2
2
2 YourWeCall speaker
Introduction
4
4
4
5
What's in the box
Product overview
3 Get started
6
6
6
6
Charge the WeCall speaker
Turn on the WeCall speaker
Connect the WeCall speaker
4 Use theWeCall speaker
Use as a speaker phone
8
8
Use together with the WeCall app
(for iPhone or Android phone)
Use as a Bluetooth or PC speaker
8
10
5 Product information
6 Troubleshooting
11
12
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Do not place any sources of danger on
the device (e.g. liquid filled objects, lighted
candles).
1 Important
Warning
• Never remove the casing of this device.
• Never lubricate any part of this device.
• Never place this device on other electrical equipment.
• Keep this device away from direct sunlight, naked
flames or heat.
Important safety information
The translation of this document is for
reference only.
In the event of any inconsistency between the
English version and the translated version, the
English version takes precedence.
About replacement of parts/
accessories
•
•
•
•
•
Follow all instructions.
replacement parts/accessories.
Heed all warnings.
Do not use this device near water.
Clean only with dry cloth.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
•
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce
heat.
Notice
•
•
Only use attachments/accessories specified
by the manufacturer.
Refer all servicing to qualified service
personnel. Servicing is required when the
device has been damaged in any way, such
as liquid has been spilled or objects have
fallen into the device, the device has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
This product complies with the radio
interference requirements of the European
Community.
Hereby, Philips Consumer Lifestyle, declares that
this speaker is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
•
Battery usage CAUTION –To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit,the batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
A copy of the EC declaration of Conformity
is available in the Portable Document Format
(PDF) version of the user manual at www.
philips.com/support.
A copy of the EC declaration of Conformity
is available in the Portable Document Format
(PDF) version of the user manual at www.
philips.com/support.
•
•
2
CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
The device shall not be exposed to
dripping or splashing.
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Skype is a trademark of Skype or its related
companies.Although this product has been
tested and met our certification standards for
audio and video quality, it is not endorsed by
Skype, Skype Communications S.a.r.l. or any of
their related companies.
Always bring your product to a professional to
remove the built-in battery.
No emergency calls with Skype
Skype is not a replacement for your ordinary
telephone and can’t be used for emergency
calling.
Note
• The type plate is located on the bottom of the device.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 YourWeCall
speaker
To fully benefit from the support that Philips
com/welcome.
Introduction
This Bluetooth conference speaker (WeCall
speaker) allows you to:
•
•
•
connect to a Bluetooth enabled
smartphone and make a mobile or
VoIP call through the WeCall speaker
directly.
connect to a PC/Mac through the
supplied USB cable and make aVoIP
call through the WeCall speaker
directly.
connect to a Bluetooth enabled iPhone
and make a conference call through
the WeCall speaker with the help of
the WeCall App.
•
•
enjoy music from a Bluetooth-enabled
mobile device or a PC/Mac.
enjoy music from a PC/Mac connected
through the supplied USB cable.
What’s in the box
Check and identify the following which are
included with your WeCall speaker:
•
•
•
•
WeCall speaker
Carrying case
USB cable
Printed materials
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Product overview
a
i
h
g
b
c
f
e
d
f USB/ source switch
a
/
•
Switch between the USB or Bluetooth
audio sources.
•
Adjust volume during a call or music
play.
g
b ON/OFF power switch
•
•
Answer an incoming mobile call.
End an ongoing mobile call.
•
Power on or off the WeCall speaker.
c CLEAR
h Source indicator
•
Remove the existing pairing
information.
•
•
Turns blue in Bluetooth mode.
Turns green in USB mode.
d Charge indicator
Turns red when the battery is running
•
i
low, or when you charge the WeCall
Speaker.
•
Mute the 4 built-in microphones of the
WeCall speaker during a call so that
the other party cannot hear you.
e Micro USB socket
For connection with the supplied USB
cable.
•
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Get started
Turn on theWeCall speaker
•
Slide the power switch to the ON position.
» In Bluetooth mode, the status indicator
turns blue.
Caution
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
» In USB mode, the source indicator
turns green.
Always follow the instructions in this chapter in
sequence.
Charge theWeCall speaker
•
Connect the WeCall speaker to a PC/Mac
through the supplied USB cable.
» The charge indicator turns red.
» When the WeCall speaker is fully
charged, the charge indicator turns off.
•
To turn off the WeCall speaker, slide the
power switch to the OFF position.
Connect theWeCall speaker
Option 1: Connect to a Bluetooth-
enabled device
You can pair the WeCall speaker with a
Bluetooth-enabled mobile device (such as
your mobile phone or tablet) or PC/Mac.Then
you can enjoy music from the WeCall speaker,
or use it as a speaker phone when you make
mobile orVoIP calls.
Note
•
You can also charge the WeCall speaker
through a USB power adapter (not
supplied).
• The effective operation range between the WeCall
speaker and your Bluetooth-enabled device is
approximately 10 meters (30 feet).
Tip
1
Slide the source switch at the bottom of
the WeCall speaker to the position.
• When the battery is low, the charge indicator flashes
red.
• It takes approximately 2 hours to fully charge the
WeCall speaker.
• The fully charged WeCall speaker supports
approximately 8 hours of operation.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Option 2: Connect through USB
The USB cable charges the WeCall speaker
and can also be used to connect the WeCall
speaker to a PC/Mac to enjoy music or use it as
a speaker phone when you makeVoIP calls.
1
Slide the source switch at the bottom of
the WeCall speaker to the USB position.
2
3
Enable Bluetooth on your Bluetooth-
enabled device.
Select ‘PhilipsWeCall speaker‘ on your
Bluetooth-enabled device and if necessary
input ‘0000’ as the paring password.
» The source indicator starts to flash
blue.
» After successful pairing and connection,
the source indicator turns solid blue
and the WeCall speaker beeps.
2
Connect the WeCall speaker to a PC/Mac
through the supplied USB cable.
» The source indicator turns green.
Note
• To pair with a new Bluetooth-enabled device, you can:
• 1. Hold CLEAR at the bottom of the WeCall speaker
for more than 3 seconds to remove the existing
Bluetooth connection.
• 2. Disable the Bluetooth function on the currently
connected device.
• The WeCall speaker can memorize up to 4 paired
devices.When you pair with another Bluetooth-enabled
device, the first memorized device will be overridden.
Tip
• For PC/Mac, to ensure stable performance, the USB
connection mode is recommended.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If theWeCall speaker has been connected to a
PC/Mac through the USB cable:
4 Use theWeCall
speaker
Use as a speaker phone
If theWeCall speaker has been connected to
a Bluetooth-enabled mobile phone or other
devices such as a tablet or PC/Mac:
1
2
3
Make sure that you have selected the USB
source on the WeCall speaker.
Make aVoIP call (such as a SkypeTM call)
on your PC/Mac.
Use the WeCall speaker as a speaker
phone during the call.
Use together with theWeCall
App (for iPhone)
1
2
Make sure that you have selected the
Bluetooth source on the WeCall speaker.
1
Download PhilipsWeCall to your iPhone.
Make a mobile orVoIP call on your mobile
phone, or aVoIP call (such as a SkypeTM
call) on your tablet or PC/Mac.
3
Use the WeCall speaker as a speaker
phone during the call.
Tip
• When there is an incoming mobile call, you can press
to answer the call.
• During a mobile call, you can press
to end the call.
to mute the 4
• During a mobile call, you can press
built-in microphones of the WeCall speaker so that the
other party cannot hear you.
2
‘Option 1: Connect to a Bluetooth-enabled
• During a mobile orVoIP call, you can use
the WeCall speaker to adjust volume.
/
on
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Confirm the telephone number and code.
3
4
Set events for conference calls in the
calendar of your iPhone or Android phone.
Run PhilipsWeCall and import conference
calls from your calendar.
6
Make a conference call.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Tip
• During a call, you can use
speaker to adjust volume.
• During a call, you can press
/
on the WeCall
• During audio play, you can use
speaker to adjust volume.
• During audio play, you can press
WeCall speaker.
/
on the WeCall
to mute the
to mute the WeCall
speaker so that the other party cannot hear you.
• During a call, you can press
• After a call, you can press
redial the last number.
to end the call.
twice consecutively to
Use as a Bluetooth or PC
speaker
1
Make sure that you have selected the
correct source on the WeCall speaker.
2
In Bluetooth mode, start audio play on the
Bluetooth-enabled device and then listen
from the WeCall speaker.
•
In USB mode, start audio play on the PC/
Mac and then listen from the WeCall
speaker.
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Product
information
Amplifier
Rated Output Power
Frequency Response
2W RMS
80Hz -16k Hz,
±3dB
Signal to Noise Ratio
>75dB
Bluetooth
Bluetooth® version V2.1 + EDR
Frequency band
2.402-2.480 GHz ISM
Band
Range
10m (free space)
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
4ohm
1" speaker
>84dB/1W/1m
General Information
DC Power Input
Battery
Input: 5VDC, 1 A
Model No.: SDL-553055-
1000mAh
Rating voltage and
capacity: 3.7VDC,
1000mAh
Dimensions
- Main Unit (w x
h x d)
110 x 28 x 110 mm
Weight
- With Packing
- Main Unit
0.33 kg
0.17 kg
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Make sure that the WeCall speaker and
your Bluetooth-enabled device are within
the effective operation range, that is,
approximately 10 meters (30 feet).
Remove any obstacle between the WeCall
speaker and your Bluetooth-enabled
device.
Check the Bluetooth setting on your
device to be connected with the WeCall
speaker (see the user manual of the
specific device for details).
Hold CLEAR at the bottom of the
WeCall speaker for more than 3 seconds
to reset, and then try again.
If there is any issue with Bluetooth
connection to a PC/Mac, upgrade the
Bluetooth driver of your PC or the iOS
version of your Mac.
6 Troubleshooting
Warning
•
•
• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
•
•
No power
•
After first-time pairing with a Mac,
the WeCall speaker may be shown as
disconnected. It is a not a malfunction.You
just need to makeVoIP calls or play music
through the WeCall speaker directly to
activate the Bluetooth connection.
•
•
Recharge the WeCall speaker (see ‘Charge
No sound
•
Press
/
on the WeCall speaker to
adjust volume.
•
Adjust volume on the connected device,
such as your mobile phone, tablet, or PC/
Mac.
•
•
•
•
Check whether you have selected the
correct source.
Check whether the WeCall speaker is
switched on.
Check the Bluetooth or USB connection
to the WeCall speaker.
Check whether you have started audio
play or any call on the connected device.
Failed to set up Bluetooth connection
•
•
Check whether you have selected the
Bluetooth source.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications are subject to change without notice
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
AECS7000_00_UM_V1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|