DSR 300/00
DSR 310/00
U
B
M
P
K
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick installation guide
Connecting to aTV and aVCR/DVD player using SCART Support
Satellite
Dish Antenna
to AC outlet
Satellite Receiver
Cable or Off-air Antenna
TV set
VCR/DVD
IN FROM ANT
OUT TO ANT
EXT 1
EXT 2
SCART
Note: for best DVD/VCR viewing, connect the DVD/VCR SCART EXT 1 directly to a SCART
of the TV set.
Connecting to a Digital Amplifier/HomeTheatre/HiFi set
to AC outlet
Satellite Receiver
A
B
Audio equipment
AUDIO
Analogue
input
Digital
input
L
R
QUICK INSTALLATION GUIDE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Safety instructions
For best results
2
2
2
2
3
5
First installation
15
5.1
Menu language and port
selection
Mains connection
Meaning of symbols
Quick installation guide
15
16
16
17
17
5.2
5.3
Channel scanning
Scanning failure
Connecting to a TV and aVCR/DVD
player using SCART Support
5.3.1 Antenna Setting
5.3.2 Signal test
3
3
Connecting to a Digital Amplifier/Home
Theatre/HiFi set
6
GeneralViewing Function 18
6.1
6.2
6.3
Receiver wake up
Channel Information
Channel selection
18
18
18
1
Introduction
6
2
Product description
Unpacking the product
Front panel
7
7
8
9
6.3.1 Using <P+/P-> or
numeric keys
2.1
2.2
2.3
18
19
19
19
19
19
20
20
20
20
6.3.2 Using the channel list
Rear panel
6.4
Channel list
6.5
6.6
TV or Radio Mode selection
Volume & Audio Control
3
Remote control
10
6.6.1 Volume control and Mute
6.6.2 Audio Control
4
Connecting your receiver
12
12
4.1
Connecting to a Satellite
Antenna and a TV
6.6.3 Audio language
6.6.4 Subtitles language
4.2
4.3
Connecting to a TV and a
VCR/DVD player using
the SCART Support
6.7
Recording timers
13
14
6.7.1 To set a timer from the guide 20
Connecting to a Digital
Amplifier/Home Theatre/HiFi
system
6.7.2 To set or modify a timer
from the Timer menu
21
4 TABLE OF CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
6.7.3 To delete a running timer
while watching digital TV or
listening to digital radio
7.5
Timer Manager
26
27
28
28
28
28
29
29
31
31
32
32
33
33
33
7.5.1 Recording timer
7.5.2 Reminder
21
21
6.7.4 To delete a running timer set
while the receiver was in
standby
7.5.3 Sleep timer
7.6
Setup menu
7.6.1 Time Setting
7
Menu
22
22
7.6.2 System Setting
7.6.3 Remote Control setting
7.1
General information
7.1.1 Basics about menu navigation 22
7.7
Installation
7.1.2 Cancel/Store changes
22
7.7.1 Antenna Setting
7.7.2 Add Service
7.7.3 Signal Test
7.2
Guide (Electronic
Programme Guide)
22
23
24
7.3
Channel Manager
7.7.4 Product Identifier
7.7.5 Factory Default
7.7.6 Software update
7.3.1 Channel Pool
7.3.1.1 To delete channels from
the Channel Pool
24
7.3.1.2 To move channels in the
Channel Pool
24
24
8
MenuTree
34
36
38
7.3.1.3 To lock channels
7.3.1.4 To sort channels in the
pool
9
Troubleshooting
Technical specifications
25
25
26
26
26
7.3.2 Favourites
10
7.4
Parental Control
7.4.1 To enable Menu Lock
7.4.2 To set the Parental Rate
7.4.3 To change your receiver's
Pin Code
26
TABLE OF CONTENTS 5
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
Thank you for buying this product from Philips and congratulations!
The Philips Digital Satellite Receiver allows you to view a wide variety of free-to-air satellite channels
with the best digital picture and sound quality.
With this product you can enjoy advanced functions and features including:
- Digital picture and sound quality
- Wide screen format
- TV SCART andVCR/DVD SCART connector
- Up to 4,000 presets for TV and Radio channels
- Easy installation and use through the well-tested Euphoria User Interface
- Fast zapp
- Personal channel list and favourite lists
- Electronic Programme Guide with information about current and next programmes
This User Manual covers the installation of your receiver and the necessary steps to use the various
functions, so you can obtain the best from standard as well as unique features.
Lucas Covers
Paris, February 2004
6 INTRODUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Product description
2.1 Unpacking the product
Unpack the receiver and check to make sure that all of the following items are included in the
package:
- 1 x Remote Control Unit
- 1 x User Manual
- 2 x AA batteries
- 1 x SCART Cable
- 1 x Power Cord.
- 1 x Warranty booklet
Plastic bags can be dangerous. Keep the bag away from babies and children to prevent
suffocation.
The symbol
on the packaging and User Manual means that the materials are recyclable.
PRODUCT DESCRIPTION 7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Front panel
Q
W E
R
1
2
3
4
STANDBY button: . . . . . . . . . . . . . . . . . . . . . . . . Switch the receiver OFF.
Red LED indicator: . . . . . . . . . . . . . . . . . . . . . . . . Display receiver status (see status indicator table).
Green LED indicator: . . . . . . . . . . . . . . . . . . . . . Display receiver status (see status indicator table).
Remote control receiver window.
Status indicator table
LED
Left-hand LED
(Red)
Right-hand LED
(Green/Orange)
Mode
Receiver connected to the mains or in
Standby mode
ON
OFF
OFF
ON
Watching TV or listening to the Radio
Pressing a remote control key
Fast blinking
Depending on
current mode
Timer active
ON
ON
OFF
Timer active in Standby
Software download
Slow blinking
Depending on
current mode
Fast blinking
8 PRODUCT DESCRIPTION
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Rear panel
Q
W
E
R
U
I
T
Y
1
2
3
4
5
6
LNB IN (*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connect the coaxial cable from the satellite dish antenna.
Refer to chapter 5 for recommended connection diagrams.
RF OUT (*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . RF output used to connect your receiver to aVCR/TV set to
watch analogue channels only, or to connect another receiver.
VCR (*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCART (1) socket to connect your video recorder or DVD
player/recorder
SERIAL (*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS232 socket for serial data transfer to a PC or another
receiver
TV (*): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCART (1) socket to connect to your TV set or a video
projector
L/R AUDIO OUT (*): . . . . . . . . . . . . . . . . . Left/Right outputs to connect your HIFI/Audio receiver
system
7
8
DIGITAL OPTICAL OUT (*): . . . . . . . Digital output to connect your HIFI/Audio receiver system
230V~50Hz 20W max (**): . . . . . . . . . . Socket to connect the power cord
Note: the label showing the type and serial number is underneath the receiver.
(1) SCART is also called Euroconnector or Peritel.
* Safety Extra Low Voltage
** Hazardous Voltage
PRODUCT DESCRIPTION 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Remote control
Mute
Standby
- Audio mute
- Standby
V
(blue) resp.V (white)
Scrolls one Page Up or one
Page Down in guide or
favourite lists
RED, GREEN,YELLOW,
BLUE
TEXT is not active
GUIDE
- Open Now & Next Guide
INFO
- Open info banner
- Show extended programme
information
- Close banner
TIMER
- Set a recording timer when
watching Digital TV or from
the GUIDE feature.
FAV
- Toggle between favourite lists
SUBTITLE
- Temporarily starts/stops or
change Audio Subtitling
I-II
- Temporary update of audio
language and selection of
audio mode
The “TIMER, 0” sequence
keystroke deletes the current
running timer
MENU
- Open/Close menu (in digital
TV mode)
CURSOR keys
BACK
- Select the previously watched
digital TV channel
- In menu mode:
- The t and y cursor keys
are used to move within the
menus and lists
- The u and i cursor keys
are used to select a value in a
menu item
Either exit the menu or bring
selection back one level and
cancel the changes you made.
P+ / P-
- Select next / previous
channel
OK
- Select / call up channel
lists / zap
VOLUME
+/ -
TV / RADIO
-Volume up / down.
- Toggle between
TV / Radio mode
0-9
TV / STB
- Channel selection in digital
TV mode
-Toggle between Digital and
Analogue TV/VCR/DVD.
10 REMOTE CONTROL
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not dispose of the batteries with
your household waste.
The Philips batteries supplied with your receiver’s remote do not contain heavy metals such as
Mercury or Lead Cadmium. Nevertheless, in many countries, exhausted batteries cannot be disposed
of with your household waste.
Please enquire about the local regulations concerning the disposal of used batteries.
REMOTE CONTROL 11
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Connecting your receiver
There are several ways you can connect and incorporate your digital receiver into your existing
audio/video equipment set-up.
Warning!
Before starting to connect:
- Unplug all equipment (TV set as well as theVCR and/or DVD if required) from the mains.
- Do not connect your digital receiver to mains supply now.
- Check your current wiring: you may not need to modify your existing Audio/Video set-up
connections if they already match the connection diagrams below.
- Depending on your existing set up, choose the most suitable connection method for incorporating
your digital receiver into your existing Audio/Video set-up. Please read chapters 4.1 and 4.2
Note: for the installation of outdoor equipment such as the dish antenna, refer to the manuals supplied with
the equipment.When adding new equipment, be sure to refer to the related installation instructions of the
manual.
4.1 Connecting to a Satellite Antenna and aTV
12 CONNECTING YOUR RECEIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Connecting to aTV and aVCR/DVD player using
the SCART Support
Satellite
Dish Antenna
to AC outlet
Satellite Receiver
Cable or Off-air Antenna
TV set
VCR/DVD
IN FROM ANT
OUT TO ANT
EXT 1
EXT 2
SCART
Note: for best DVD/VCR viewing, connect the DVD/VCR SCART EXT 1 directly to the TV SCART.
CONNECTING YOUR RECEIVER 13
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Connecting to a Digital Amplifier/HomeTheatre/HiFi system
to AC outlet
Satellite Receiver
A
B
Audio equipment
AUDIO
Analogue
input
Digital
input
L
R
Analogue connection (A)
Connect the L/R audio output sockets to the relevant L/R audio input sockets of your audio
equipment using a double CINCH cable (not supplied). Consult the user manual of your audio
equipment to choose the proper analogue audio inputs.
Digital connection (B)
Connect the audio “DIGITAL” output socket to the relevant digital audio input socket of your audio
equipment using a single CINCH cable (not supplied). Consult the user manual of your audio
equipment to choose the proper digital audio input.
Note: with this connection set up you can only control the audio volume up/down and mute from your audio
equipment.
14 CONNECTING YOUR RECEIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
5 First installation
Requirements for fast and successful start-up are as follows:
- you already have a satellite antenna installed;
- your antenna is correctly pointed at the applicable satellite
transponders (Astra, Hotbird, Eutelsat, …);
- your receiver is connected to the antenna,TV set and
other equipment according to the diagrams in chapter 4.
Switch ON the receiver and TV set.The welcome screen
appears.
5.1 Menu language and port selection
- When the welcome screen is displayed, press <OK> to
access the Easy installation screen.This screen prompts
you to select your favourite menu language as well as the
appropriate port configuration. Depending on your
DiSEqC set-up, you can select satellites for one or more
ports. If you do not have any DiSEqC switch, select port A
only.
- Go to the Antenna Setting screen by pressing the <Red>
key of the remote control to adjust the settings for this
port to suit your requirements. Press the <Green> key to
obtain some help on how to point the antenna in the right
direction for the best signal reception.
- Make the appropriate selections, and then press <OK> to
start scanning for channels.
FIRST INSTALLATION 15
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Channel scanning
During the scanning process, the following information is
reported on screen:
- the number of TV and Radio channels detected,
- the scanning progress, indicated as a percentage,
- the strength of the signal and the quality of reception.
Note: if you press <OK> during the scanning process, you
interrupt the scanning and return to the Easy installation screen.
Please note that it may take a few seconds before the receiver
reacts to the <OK> key press. In this case, none of the channels
found are stored.
When scanning is successfully completed, a completion
message is displayed as well as the number of channels
detected.
Press <OK> to tune the receiver to the first channel in the
list.
5.3 Scanning failure
In case of channel scanning failure, a failure message is
displayed.
Before starting a new scanning
The following checks are recommended:
- antenna cable,
- antenna connection to your receiver (see chapter 5.1 and
further),
- number of channels available in the region corresponding
to your area.
16 FIRST INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.1 Antenna Setting
- To continue, press <OK>.The Antenna Setting screen
appears to help you with the installation process and to
adjust your settings if needed.
- Choose a satellite for the applicable port and enter the
LNB type (universal by default) and LNB frequencies.You
can test the signal by pressing the <Green> key of the
remote control.
- Press <OK> to start scanning again. If the same failure
message appears after a while, refer to the
Troubleshooting chapter.
5.3.2 Signal test
You will not receive the signal from the satellite if your
antenna is not positioned correctly, even though you have
entered the correct values in the Antenna Set up menu.Your
receiver therefore provides precise Antenna Direction
information to help you direct your antenna toward a
satellite.
- Press the <Green> key of the remote control to access
the Signal Test screen. It indicates the strength of the
incoming satellite signal as well as the quality of reception.
- If both the signal strength and reception quality are
inadequate, you may need to change the direction in which
the antenna is pointing until the level becomes satisfactory.
- Press <OK> to start scanning again.
Note: if the same failure message appears after a while, refer to
the Troubleshooting chapter.
FIRST INSTALLATION 17
Download from Www.Somanuals.com. All Manuals Search And Download.
6 GeneralViewing Function
This section describes the basic functions available while
watching satelliteTV or listening to satellite Radio. For general
menu navigation information, see Basics about menu navigation.
6.1 Receiver wake up
Your receiver is in standby.To wake it up, press any of the
following on the remote control:
- numerical keys,
- <P->/<P+>.
Note: the Standby button can only be used to switch the
receiver off.
6.2 Channel Information
Every time you change channels, programme information
appears on screen, displaying:
- The channel name and number in the current channel list.
- The current programme name.
- Icons indicating the channel properties, e.g. channel lock status.
- A bargraph indicating the start time of the current
programme, the start time of the next programme, and
the current progress.
icon description
alternate audio
language/format
While watching a channel, you can display the current
channel information at anytime by pressing <INFO> on the
remote control. Press <INFO> again to get more
information about the current programme.
current favourite list
maturity rating locked
scrambled channel
locked channel
Note: channel information is displayed for 3 seconds as per
default.This can be adjusted from the System Setting screen.
subtitles presence
teletext presence
6.3 Channel selection
6.3.1 Using <P+/P-> or numeric keys
To switch channels, use <P+>/<P-> or the numeric keys of
the remote control.
18 GENERAL VIEWING FUNCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3.2 Using the channel list
- For a complete overview of the available channels while
watching satellite TV or listening to satellite radio, press
<OK> on the remote control.A channel list is displayed
on the left-hand side of the screen.
Note: if you press <BACK>, the channel list disappears.
- To select a channel, scroll up or down this channel list, and
then press <OK> to watch it.
6.4 Channel lists
While watching digital TV or listening to digital radio, you
can enable all available channel lists by pressing <FAV> on
the remote control. Successively press <FAV> to toggle
between the favourite lists you created and the full channel
list.The current channel list is indicated on the left-hand side
of the banner.
When one of the favourite lists is activated, you zap only
through the channels this list contains.
To create and edit your favourite lists, see paragraph 8.3.
6.5 TV or Radio Mode selection
While watching satellite TV or listening to satellite radio,
press TV/RADIO on the remote control to toggle between
TV and Radio modes.
6.6 Volume & Audio Control
6.6.1 Volume control and Mute
- To increase or decrease the volume, use <
remote control.
> on the
Note: the volume level can also be controlled from your TV.
- To mute the sound, press < > on the remote control
- To resume normal sound, press this key once again.
Note: change of volume is signalled on-screen using a bargraph,
while audio mute is signalled with an icon in the top right corner
of the screen.
GENERAL VIEWING FUNCTION 19
Download from Www.Somanuals.com. All Manuals Search And Download.
6.6.2 Audio Control
- To access audio settings, select the Setup menu from the
main menu, then select System Setting.The System Setting
screen appears.
- Select Audio Output. Default Audio Output setting is Stereo.
- Select the desired value (Left, Right, Mono, or Stereo) and
press <OK> to save your changes and exit the screen.
6.6.3 Audio language
To select your preferred audio language:
- Select System Setting from the main menu.The System
Setting screen appears.
- Scroll to Audio Language, and then select the desired
language.
- Press <OK> to save your changes and exit the screen.
Note: if you want to change the audio language for a particular
programme, press <I-II> on the remote control to directly access
the audio language options available for this programme.
Available languages depend on the audio content transmitted.
6.6.4 Subtitles language
To select your preferred Subtitles language:
- Select System Setting from the main menu.The System
Setting screen appears.
- Scroll to Subtitle Language, and then select the desired
language.
- Press <OK> to save your changes and exit the screen.
Note: if you want to change the Subtitle language for a particular
programme, press <
> on the remote control to directly access
the Subtitles language options available for this programme.
Available languages depend on the content transmitted.
6.7 Recording timers
Recording timers are used forVCR or DVD recordings.
6.7.1 To set a timer from the guide
- Select Guide from the main menu to access the Electronic
Programme Guide.
- Move to the desired programme using the arrow keys.
20 GENERAL VIEWING FUNCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
- Press the <Red> colour key to set a recording timer on
the selected programme.Alternatively, press the <Green>
colour key to set a reminder on the programme.
- Enter your PIN code if necessary, and then set the timer
type as appropriate. By default, other settings correspond
to the selected programme.
- Press <OK> to confirm and exit the screen.
6.7.2 To set or modify a timer from theTimer
menu
- Select the Record Timer item from the Timer sub-menu
or press the <TIMER> key of the remote control to
access the Recorder screen.
- Select an available Timer Number or select the timer you
want to modify.
- Set the values of the recording parameters using the
arrow or numerical keys as appropriate (for more details,
refer to paragraph 8.5.1).
- Press <OK> to confirm.
Note: an existing recording timer can be disabled from the
Recorder screen by selecting Disable as Timer Type.
6.7.3 To delete a running timer while watching
digitalTV or listening to digital radio
A timer is running and you are watching the programme you
are recording. Recording is signalled by two front LEDs, the
right-hand one lit in red and the left-hand one lit in green.
To delete the running timer:
- Press the key sequence “TIMER, 0”.The red light then
switches off and you can change channels.
6.7.4 To delete a running timer set while the
receiver was in standby
A timer is running that was set while your receiver was in
standby. Recording is signalled by the right-hand red LED,
which is blinking slowly.
- Press the key sequence “TIMER, 0” to delete the running
timer.The red light then switches off and you can change
channels.
Note: when a recording timer is active, you cannot change digital
channels, but you can switch to analogue TV using the <TV/STB>
key and zap through analogue channels.
GENERAL VIEWING FUNCTION 21
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Menu
7.1 General information
The Menu gives access to all the functions of your receiver:
o Guide
o Channel Manager
o Parental Control
o Timer Manager
o Set-up Menu
o Installation.
7.1.1 Basics about menu navigation
While watching TV or listening to the radio:
- Press <MENU> to display the Menu screen.
- Press t or y to scroll up or down and select the desired
menu item.
- Press <OK> to display the corresponding sub-items.
- Press t or y to move to the desired sub-item.
- Press the u or i button to select a value in a menu item.
Note: press <BACK> to go back one step.
7.1.2 Cancel/Store changes
- Either press the <BACK> button to exit the screen
without storing changes.
- Or press the <OK> button to validate changes and exit
the screen.
Note: to open a locked menu item (indicated by a lock icon ),
you need to enter your Pin Code.
7.2 Guide
(Electronic Programme Guide)
The TV/Radio Electronic Programme Guide (EPG) provides
an overview of available TV and Radio channels, and
programmes the broadcasters have scheduled, starting with
the current programme.
22 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
To view EPG data:
- Press <GUIDE> on your remote control when watching a
channel, or select the Guide item from the Menu and
press <OK>.
- Highlight the name of the programme for which you want
more detailed information.
- Press the <INFO> key of the remote control once to get
extended information (programme description) and once
again to close it.
- Press <OK> to view the corresponding channel.
Note: a “No information yet” message is displayed if the selected
channel does not provide EPG data. It may take a few seconds
before data can be displayed.
To set a recording timer from the Guide:
- Press the <Red> colour key once to set a recording timer
for the programme currently highlighted.
To set a reminder from the Guide:
- Press the <Green> colour key to set a reminder for the
programme currently highlighted.
If you want to check the previous or next information of the
channel, please press u or i on the remote control.
7.3 Channel Manager
The Channel Manager function is used to organize your
channel list (channel POOL) and create and edit your
favourite lists.
Note: switch from TV channel lists to Radio channel lists by
pressing <TV/RADIO>. Radio Channel Manager has the same
operation as TV channel Manager.
Select Channel Manager from the Menu and press <OK> to
access the Channel sub-menu, containing the Channel POOL
and Favourites options.
MENU 23
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3.1 Channel Pool
Select Channel POOL and press <OK> to access the
Channel Pool screen.
In this screen, you can:
o delete channels from the channel list,
o move channels to a different position in the list,
o lock channels,
o sort channels.
7.3.1.1 To delete channels from the Channel Pool
The Delete feature is used to permanently delete a channel.
- Press the <Red> colour key of the remote control to
enable the feature. Select the channel you want to delete
by highlighting it and pressing <OK>.A marker appears in
place of the channel number.
- Press <OK> again to cancel the selection. Deletion only
takes place when you exit the screen.You are then
prompted to confirm the changes that should be taken
into account.
Note: the deleted channel cannot be recovered unless you do a
channel scan again.
7.3.1.2 To move channels in the Channel Pool
The Move feature is used to change the position of a
channel in the list.
- Press the <Green> colour key of the remote control to
enable the feature.
- Select the channel you want to move by pressing <OK>.
Press <OK> again to cancel selection.
- Then highlight the line to which you want to move the
selected channel and press <OK>.The selected channel
moves to the desired location and the channel number
changes accordingly.You are prompted to confirm the
changes when you exit the screen.
7.3.1.3 To lock channels
The Lock feature is used to lock channels.
- Press the <Yellow> colour key of the remote control to
enable the feature.
- Enter your 4-digit Pin Code.
24 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
- Select the channel you want to lock by pressing <OK>.
The selected channel is marked with this . Press <OK>
again to cancel selection.You are prompted to confirm the
changes when you exit the screen.
Note: you can only use this function once you have set up your Pin
Code in the Parental Control part of the Setup Menu.
7.3.1.4 To sort channels in the pool
The Sort feature is used to sort channels.
- Press the <Blue> colour key of the remote control to
enable sorting options.
- Then press the <Red> key to sort the channels in
alphabetical order (channel name) or the <Green> colour
key (provider) to sort the channels according to the
service provider, or the <yellow> colour key to restore
the original order.
7.3.2 Favourites
Select Favourites from the Channel sub-menu to access the
screen used to create and edit up to three TV and three
Radio channel lists according to your personal preferences.
To create a favourite list:
- Individually select the desired channels from the list by
scrolling to the corresponding channel and pressing
<OK>. Press <OK> again to cancel selection.
- Alternatively, use the red colour key to select all channels
or green colour key to deselect all channels.
Note: selected channels are marked with a tick.
To create additional favourite lists:
- Press <FAV> to select the next favourite list (up to
Favourite 3).
- Then proceed as indicated above.
- Press <BACK> to exit the screen.
- When prompted, confirm your changes by pressing <OK>.
When you activate one of the favourite lists by pressing
<FAV> while watching digital TV or listening to digital radio,
the receiver only zaps through your favourite channels.
- Press <FAV> to again toggle between your favourite lists
and the full channel list.
MENU 25
Download from Www.Somanuals.com. All Manuals Search And Download.
7.4 Parental Control
Parental Control is used to:
- Block access to your receiver and its Menu;
- Specify a parental rate to protect access to programmes
using a PIN code in case the parental rate transmitted
with such programmes is higher than the rate you set;
- Enable channel lock using a Pin Code in order to prevent
children from watching these channels.
You must enter your 4-digit Pin Code to access the
various settings.
7.4.1 To enable Menu Lock
To lock access to every sub-menu of your receiver, set Menu
Lock to ON.
7.4.2 To set the Parental Rate
Select the desired Parental Rate:
from 3 to 18, or None.
7.4.3 To change your receiver's Pin Code
The receiver's Pin Code default value is 1111.
To change your Pin Code:
- Scroll down to New Pin Code and enter your new Pin Code.
- Scroll down to Confirm Pin Code and enter your new
Pin Code again.
Note: once you have changed your Pin Code, keep it secret to
prevent others from using it. If you forget or lose your Pin Code,
please refer to the Troubleshooting chapter.
- Press <OK> to confirm your changes and exit the screen.
7.5 Timer Manager
The Timer Manager is used to set:
- Recording timers for the programmes you want to
recordusing yourVCR or DVD recorder,
- Reminders for programmes you want to see in the near future,
- Sleep timers.
26 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
To be able to record a digital channel using aVCR or
DVD recorder, you must set both your recorder and
receiver:
- You must set a timer on your receiver.
- You must also enable recording on theVCR or DVD
recorder (refer to theVCR or DVD recorder user manual).
7.5.1 Recording timer
Select the Record Timer item from the Timer
sub-menu or press the <TIMER> key of the to access the
remote control to access Recorder screen.
To activate a recording timer:
- Select values for the following:
• Timer number: used to identify the timer. Select the
number corresponding to the timer you want to use.
• Channel Name: select the channel on which the
programme you want to record is broadcast using the
uor ikey.
Note: alternatively, press <OK> when the highlight is on Channel
Name to display the list of available channels.Then scroll to the
desired channel and press <OK> to select it.
• Timer Type: select Daily to record once every day,
Weekly to record once every week, Monthly to record
once every month, or One time for a single recording
at the selected time. Select Disable to cancel the timer.
- Depending on the timer type, proceed with the following:
• Month: select 1 for January, 2 for February, etc. using
the uor ikey for a single recording.
• Date: select a date using the uor ikey for single and
monthly recordings.
• Start time: select a start time using the uor ikey to
modify the default time in steps of 10 minutes or
numerical keys.
• End Time: select a end time using the uor ikey to
modify the default time in steps of 10 minutes or
numerical keys.
- Press <OK> to confirm.
Note: when a recording timer is active, you cannot change digital
channels, but you can switch to analogue TV using the <TV/STB>
key and zap through analogue channels.
MENU 27
Download from Www.Somanuals.com. All Manuals Search And Download.
7.5.2 Reminder
When you set a reminder for a particular programme, the
receiver sends a warning at the start of that programme and
switches automatically to the right channel if you accept the
reminder message.
Select the Reminder item from the Timer sub-menu to
access the Reminder screen.
To activate a reminder:
- Set the values of the reminder parameters using the arrow
keys or numerical keys as appropriate.
- Press <OK> to confirm.
Note: an existing reminder can be disabled by selecting Disable as
TimerType in the Reminder screen.When a timer is already active
(recording in progress), press <TIMER> then <0> to cancel this timer.
7.5.3 Sleep timer
You can set a sleep timer to automatically switch your
receiver to Standby mode after a given time lapse.
Select the Sleep item from the Timer sub-menu to access
the Sleep screen.
To activate a sleep timer:
- Enter the time lapse after which the receiver should go to
Standby using the numerical keys of the remote control.
- Press <OK> to confirm.
To disable a sleep timer:
- Select Disable instead of a time lapse.
- Press <OK> to confirm.
7.6 Setup menu
The Setup menu is used to modify the basic settings of your
receiver, including the clock time and general settings, such
asVideo and Audio output.
7.6.1 Time Setting
This feature is used to set the local time offset with respect
to actual local time normally obtained from the network.
- Select the Time Setting item from the System sub-menu to
access the Time Setting screen.
- Select the appropriate offset value (from -12 to +12).To
help you set the offset value, the names of capital cities for
28 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
which the selected value is valid are displayed at the
bottom of the screen.
- Press <OK> to store the selected value and go back to
the previous screen or <BACK> to cancel and the screen.
In case the information supplied by the satellite is not
correct, the Time Setting screen is used to set the actual
date and time using the arrow or numerical keys of the
remote control as appropriate.
7.6.2 System Setting
Note: your TV settings will be overwritten by the receiver settings.
This feature is used to set the system settings.
- Select the System Setting item from the Setup menu to
access the System Setting screen.
- Select appropriate values for the following:
• Menu Language: Dutch, English, French, German
(default value), Italian, Polish and Turkish
• Audio Language: Dutch, English, French, German
(default value), Italian, Polish and Turkish
• Screen Format: 4:3 or 16:9 (wide screen)
• TVVideo Output: RGB (default value) or CVBS
•VCRVideo Output: S-VHS or CVBS
• Start On Channel, which is tuned when you activate
your receiver from Standby
Note: if not enabled (none), the default value is the last
channel you watched before you put your receiver on
Standby.
• Subtitle Language: Dutch, English, French, German
(default value), Italian, Polish and Turkish
• Audio Output: Stereo (default value), Left, Right, Mono.
Note: access to this menu can be protected by Pin Code.
7.6.3 Remote Control setting
If you have a Philips TV set equipped with a universal remote
control which in 'STB' mode is able to perform certain
actions like channel up/down, your receiver offers you the
possibility to do so.
However, if you have other items of equipment in your home
and the Philips remote control of your receiver interferes
with them, it is recommended to change the setting of both
your receiver and remote control.
MENU 29
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the setting of your receiver:
- Press <MENU> to display the menu screen.
- Press y to scroll down to System Setting, and then press
<OK> to display the System Setting menu screen.
- Press y to scroll down to Remote Control Setting and
press <OK>.The Remote Control Setting screen appears,
indicating the current remote control setting value.
- Change the remote control setting value using
the uor ikey:
• Either select 39 to control your receiver using the TV
remote control,
• Or select 40 or 38 to keep the remote control of your
receiver from interfering with other items of
equipment.
- Press <OK> to validate the remote control setting change
on the receiver.A pop-up message appears, prompting you
to refer to the user manual instructions to change the
setting of your remote control.You must change the
setting of your remote control to be able to proceed.
To change the setting of your remote control:
- Press number keys <1> and <3> simultaneously and hold
them for at least 5 seconds.
- Release these two keys.
- Enter the new setting according to the remote control
setting value displayed on screen within the next
60 seconds:
• Either press 1 to control your receiver using the TV
remote control (setting value 39),
• Or press 3 or 5 to keep the remote control of your
receiver from interfering with other items of
equipment (setting value 40 or 38 respectively).
- Press <OK> to confirm the remote control setting change
and return to normal operation.
Note: in case you find you cannot press <OK>, repeat steps 1 to
3 above.
- Press <MENU> or <BACK> to go back to the main menu.
Alternatively you may reset your remote control to its
default setting (40) by removing the batteries and reinserting
them after more than 3 minutes.
30 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
7.7 Installation
The Installation sub-menu includes the following items:
o Antenna Setting
o Add Service
o Signal Test
o Product Identifier
o Factory Default
o Software Update.
7.7.1 Antenna Setting
This feature is used to set the antenna settings.
- Select Antenna Setting from the Installation menu to
access the Antenna Setting screen.
Note: access to this menu can be protected by Pin Code.
- Select appropriate values for the following:
• Port: up to 4 ports
Note: this item is used to configure the DiSEqC option for
multiple LNBs.
• Satellite: select the appropriate satellite using arrow
keys.
• LNB Type: select your LNB type. If you use an universal
LNB, select Universal (default value).
• LNB Freq. 1: set automatically according to the satellite
and LNB Type selected. If you have a dual LNB, enter
the proper value in the value box.
• LNB Freq. 2: set automatically according to the satellite
and LNB Type selected.
• 22KHz Tone: select the switches with which you want
to configure the antenna.
- To exit the Antenna Setting screen, press the <BACK> key
of the remote control to finish antenna setup.The message
“Are you sure you want to change the configuration of
Antenna setup?” is displayed.
- Select the <OK> button on screen and then wait for the
data to be saved.
MENU 31
Download from Www.Somanuals.com. All Manuals Search And Download.
7.7.2 Add Service
This feature is used to search for new channels.
- Select Add Service from the Installation menu to access
the Add Service screen.
- Select values for the following:
• Port: up to 4 ports
Note: this item is used to configure the DiSEqC option
for multiple LNBs.
• Satellite: select the appropriate satellite using arrow
keys.
• Transponder: select a transponder to perform a search
for this particular transponder.
• Frequency: frequency value corresponding to the
selected transponder or entered manually using
numerical keys.
• Symbol Rate: symbol rate value corresponding to the
selected transponder or entered manually using
numerical keys.
• Polarization: Hor (horizontal) orVer (vertical)
• Search options: select FTA to search for Free-To-Air
channels, or FTA+Scram… for Free-To-Air and
scrambled channels.
• Search type: select TP to perform the search for a
particular transponder, Network for a group of
transponders or 1 Sat for all the transponders of a
satellite.
Note: information about the selected satellite is displayed on the
right side of the screen.
7.7.3 SignalTest
This feature is used to test the signal strength and quality.
- Select Signal Test from the Installation menu to access the
Signal Test screen.
- Select values for the following:
• Antenna: select your antenna number
• Satellite: select the appropriate satellite using arrows
keys
• LNB Type: select your LNB type. If you use an universal
LNB, select Universal
• LNB Freq. 1: set automatically according to the satellite
and LNB Type selected. If you have a dual LNB, enter
the proper value in the value box.
32 MENU
Download from Www.Somanuals.com. All Manuals Search And Download.
• LNB Freq. 2: set automatically according to the satellite
and LNB Type selected.
• Frequency: frequency value corresponding to the
selected transponder or entered manually using
numerical keys.
• Symbol Rate: symbol rate value corresponding to the
selected transponder or entered manually using
numerical keys.
• Polarization: Hor (horizontal) orVer (vertical)
As you enter values, you can view the signal strength and
quality on the right-hand side of the screen.
7.7.4 Product Identifier
This feature is used to provide hardware and software
information.
7.7.5 Factory Default
To reset your receiver back to the factory default condition,
select Factory Default from the Installation sub-menu.
The Factory Default screen appears, displaying a warning
message. Press <OK> to confirm (selection is highlighted in
yellow).
Note: if you reset your receiver to factory default settings, you lose
all your personal settings stored previously.
7.7.6 Software update
This feature is used to set the software download mode and
type.
To manage software downloads:
- Select Software update from the Installation sub-menu.
- Select the appropriate values for the followings:
• Select mode:Auto Mode or User Mode. It is
recommended to set the update mode to Auto Mode.
• Download Type: Software, Software+Data or Data
• For instance, data is a preset list.
- Press <OK> to launch a new software search.The
software search screen appears, displaying the search
progress and the new software version.
MENU 33
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Menu tree
Guide
Channel POOL
Channel Manager
Favourites
Parental control ON/OFF
Menu lock ON/OFF
Parental Rate
Parental control
(Pin Code required)
New Pin Code
Confirm Pin Code
Timer Number
Channel Name
Timer Type
Month
Date
Start Time
End Time
Record Timer
Reminder
Timer Manager
Timer Number
Channel Name
Timer Type
Month
DiSEqC
Satellite
Date
Start Time
LNB Type
LNB Freq. 1
LNB Freq. 2
LNB Power
22KHz Tone
Sleep
Time
Set Local Time
Summer Time
Year
Month
Date
DiSEqC
Satellite
Time Setting
Transponder
Frequency
Symbol Rate
Polarization
22KHz
Search Options
Search Type
Time
Menu Language
Audio Language
Subtitle language
Screen Format
TV Output
Audio Output
VCR Output
Setup menu
System Setting
DiSEqC
Satellite
LNB Type
LNB Freq. 1
LNB Freq. 2
Frequency
Symbol Rate
Polarization
Remote Control
Setting
Banner Timeout
Transparency
Antenna Setting
Add Service
DiSEqC
Satellite
Signal Test
Installation
Frequency
Symbol Rate
Polarization
Set PID
Select mode
Download Type
Product identifier
Factory default
Software update
34 MENU TREE
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Troubleshooting
Please be aware that new software may change the functionality of your receiver.
Should you experience any difficulties with the operation of the receiver, please consult the relevant section of
this manual, including this Troubleshooting section. If the problem cannot be solved, call your dealer or a
customer service adviser.
Symptom
Cause
Remedy
The display on the front panel does Faulty power supply
not light up.
Check that the power cord is
correctly connected. Disconnect
this cord and reconnect it to
ensure it is in place.
Check that the power is available
at the wall socket.
No sound or picture but the front
panel red light is on.
Receiver in Standby
Press the Standby button.
No sound or picture but the front
panel green light is on.
Dish pointed incorrectly
Adjust the dish pointing. Check the
signal level from the Antenna Setup
menu.
Poor signal
Check the connections at the LNB
and between the LNB and the
receiver, or adjust the dish.
Receiver in TV mode
Press <TV/STB> on the remote
control once or twice.
Poor SCART connections
Incorrect dish pointing
Check the SCART connections
Adjust the dish pointing.
Poor picture
The remote control does not
operate your receiver.
Make sure the receiver is on.
Make sure you are pointing the
remote control at the receiver
front panel.
Check the batteries in your
remote control.
On-screen display working but
Poor reception/signal
No power fed to LNB
Check the installation and the
antenna positioning.
there is no reception
.
Check the cable between the LNB
and the receiver.
36 TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Remedy
Intermittent reception.
Faulty connections
Check all connections and cable.
Incorrect dish pointing
Adjust the dish pointing. Fasten the
antenna securely.
The picture is not sharp and on-
screen text is difficult to read.
TV SCART output format not set
to RGB
Change the setting of the TV
SCART item to RGB from the
System Setting menu.
TV SCART not connected to the
RGB-capable SCART socket of
your TV set.
Refer to your TV User Manual.
Inappropriate TV SCART
Use the SCART cable supplied
with your receiver.
You cannot find all the channels
you think should be available.
The signal to your aerial may be
weak.
Try retuning your receiver,
following the relevant steps in the
Quick installation chapter. If you
are still missing channels, your
aerial may need adjusting.
Your aerial may need adjusting or
your local transmitter may not be
working.
Call your local dealer.
The picture on some channels
seems to have been stretched or
squashed.
The broadcast is probably in wide
screen and the receiver settings
may not be correct.
Check the receiver “TV format”
option setting, following the
information in chapter 7.6.2. If you
have a wide screen TV, you may
also need to check the settings on
your TV.
Even if you use the number
buttons, you cannot access a
particular channel.
The parental lock has been
activated on this channel and a
message asks for your parental
code.
Enter your parental code to access
the channel or remove it as a
locked channel.
You set a timer but did not record
what you wanted.
The video was set incorrectly
Make sure that your video is set
for the same time as your digital
receiver.
The order of the channels has
changed.
They have been re-arranged as
described in chapter 7.
Refer to this chapter to change the
order again.
Note: if you have tried all of the actions suggested above, and cannot solve the problem; please contact your
dealer or service provider.
TROUBLESHOOTING 37
Download from Www.Somanuals.com. All Manuals Search And Download.
© Koninklijke Philips Electronics N.V. 2004
All rights reserved
3111 176 51785
Download from Www.Somanuals.com. All Manuals Search And Download.
|